4-inch Analog Speed Dome
User’s Manual
Version 1.0.0
Table of Contents
1 FEATURES AND FUNCTIONS ..........................................................................................1
1.1 General Introduction...................................................................................................................................................1
1.2 Features.......................................................................................................................................................................1
1.2.1 On-Screen Menu....................................................................................................................................................1
1.2.2 Proportional Pan and Tilt ......................................................................................................................................1
1.2.3 On-screen Tips.......................................................................................................................................................1
1.2.4 Preset Setup and Call ...........................................................................................................................................1
1.2.5 Auto Scan................................................................................................................................................................1
1.2.6 Auto Tour ................................................................................................................................................................1
1.2.7 Auto Pattern............................................................................................................................................................1
1.2.8 Privacy Masking .....................................................................................................................................................1
1.2.9 Auto Flip ..................................................................................................................................................................1
1.2.10 Self-diagnosis ....................................................................................................................................................2
1.2.11 Day/Night Mode (B/W & Color Mode) ............................................................................................................2
1.2.12 Auto Focus .........................................................................................................................................................2
1.2.13 Backlight Compensation ..................................................................................................................................2
1.2.14 Pan Tilt and Zoom.............................................................................................................................................2
1.2.15 3D Intelligent Location......................................................................................................................................2
1.2.16 Idle Status ..........................................................................................................................................................2
1.2.17 Image Stabilizer/Flip .........................................................................................................................................2
2 MENU .................................................................................................................................3
2.1 Screen Menu Index ..................................................................................................................................................3
2.2 Self-diagnosis System Information ..........................................................................................................................4
2.3 Main Menu ...................................................................................................................................................................4
2.4 Menu Operation ........................................................................................................................................................4
2.4.1 System Information................................................................................................................................................5
2.4.2 Display Setting .......................................................................................................................................................6
2.4.3 Camera Setting ......................................................................................................................................................6
2.4.4 Function Setting ...................................................................................................................................................10
2.4.5 Alarm Setup ..........................................................................................................................................................16
i
2.5 Dome Abnormal Phenomenon Operation........................................................................................................16
2.5.1 Restore to Factory Default Setup ......................................................................................................................16
2.5.2 PTZ Movement is not smooth ............................................................................................................................16
3 CABLE CONNECTION .....................................................................................................17
3.1 System Layout ........................................................................................................................................................17
3.1.1 System Connection .............................................................................................................................................17
3.1.2 Alarm Connection ................................................................................................................................................18
4 FAQ...................................................................................................................................19
4.1 Daily Maintenance..................................................................................................................................................19
4.2 Problems and Solutions.......................................................................................................................................19
5 APPENDIX Ⅰ THUNDER PROOF AND SURGE PROTECTION .......................................20
6 APPENDIX 2 TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS ...........................21
ii
Welcome
Thank you for purchasing our product!
This user’s manual is designed to be a reference tool for the operation of your system.
Here you can find information about this speed dome features and functions, as well as a detailed menu tree.
Please keep it well for future reference!
Before installation and operation, please read the following safeguards and warnings carefully!
iii
Important Safeguards and Warnings
1．Electrical safety
z All installation and operation here should conform to your local electrical safety codes.
z The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
z We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
z We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation Security
z No heavy stress, violent vibration or water splash are allowed during transportation, storage and
installation.
z Please use the original packing material (or the material of the same quality) when you ship it back to
the manufacturer.
3．Installation
z Do not apply power to the product before completing installation.
z Please install the proper power cut-off device during the installation connection.
z Do not put object on the product.
4．Environment
z This series product should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
z Please keep it away from the electromagnetic radiation object and environment.
z Please keep the sound ventilation.
z Do not allow the water and other liquid falling into the device.
z Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
z Thunder-proof device is recommended to be adopted to better prevent thunder.
z The grounding holes of the product are recommended to be grounded to further enhance the reliability
of the camera.
5. Daily Maintenance
z Current series product has no power button. Please unplug all corresponding power cables before your
begin installation or daily maintenance work.
z Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a
long time.
z Do not touch CCD (CMOS) component. You can use the blower to clean the dust on the surface of the
device. You can use the dry cloth with some alcohol or mild detergent to clear if necessary.
z Do not use the volatility solvent such as the benzene or thinner, or detergent with strong abradibility. It
may result in lens damage or it may adversely affect the device performance.
iv
z If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device.
z 6. About Accessories
Always use all the accessories recommended by manufacturer.
Before installation, please open the package and check that all the components are included in the package:
Contact you local retailer ASAP if something is missing in your package.
v
1 Features and Functions
1.1 General Introduction
The 4-inch analog intelligent speed dome is a product of general high level of integration and intelligence.
Its structure adopts the new design and is easy to install. It has no effect on the monitor environment. It
is featuring clear video, intelligent and etc.
Besides the features of the general series product, it adds some new functions. .The PTZ rotation speed
can automatically adjusts according to lens zoom speed. It supports various languages, real-time clock
function and protocol auto recognition. It supports 360° continuously pan, 92°tilt and 180° auto flip. It can
realize no blind spot monitor.
1.2 Features
This series speed dome has the following features:
1.2.1 On-Screen Menu
This series product menu supports multiple languages.
It is easy for you to view dome information and configure dome, camera parameters.
1.2.2 Proportional Pan and Tilt
This function keeps the image from moving too fast when there is a large amount of zoom.
This series speed dome continually decreases or increases pan and tilt speeds in proportion to depth of
zoom. When zooms speed is increasing, the camera moving speed becomes slow. When zooms speed
is decreasing, the camera moving speed becomes fast.
1.2.3 On-screen Tips
Via menu, here you can view:
z Call preset and preset ID, speed dome title when calling touring.
z Dome system temperature. (Optional. You can disable this function)
z Dome address. (Optional. You can disable this function)
1.2.4 Preset Setup and Call
Preset function is to save the address information (such as PTZ pan/tilt, focus and etc) to the memory so
that you can quickly adjust the dome and PTZ to the correct position.
1.2.5 Auto Scan
Camera scans back and forth regularly in a horizontal field. Here you need to set left and right limit and
scan speed.
1.2.6 Auto Tour
Add presets into a routine in a desired order and then set time and stop duration for each address. The
dome will begin an auto touring between these presets.
1.2.7 Auto Pattern
Memorize dome operation such as pan, tilt, and zoom to repeat. You can call it to repeat the previous
operation.
1.2.8 Privacy Masking
Privacy masking is a user-defined, four-sided area that can not be viewed by you. The masking area will
move with pan and tilt functions and automatically adjust in size as the lens zooms.
1.2.9 Auto Flip
1
As long as you continue to hold the keyboard joystick in the down position, the dome rotates 180
degrees and repositions itself for uninterrupted viewing of any subjects that passes directly beneath the
dome.
1.2.10 Self-diagnosis
There is a self diagnosis procedure when dome boots up.
z Tilt and vertical engine check
z Camera diagnosis
1.2.11 Day/Night Mode (B/W & Color Mode)
Auto/color/B&W switches in low illumination. There are several modes such as auto/manual/schedule.
This function needs the speed dome driver (camera) supported.
1.2.12 Auto Focus
Support auto focus function.
1.2.13 Backlight Compensation
Balance the brightest and darkest sections of a scene to produce a more vivid picture.
1.2.14 Pan Tilt and Zoom
Supports zoom in and zoom out during tilt and pan movement.
In this period auto focus and auto iris can still get vivid image.
1.2.15 3D Intelligent Location
Support 3D intelligent positioning function, speed dome can auto track to the specified zone. .
1.2.16 Idle Status
When there is no available order for specified period, the speed dome can implement previously set idle
operation.
1.2.17 Image Stabilizer/Flip
You can enable image stabilizer function and flip in the menu.
When there is vibration, this IS function can guarantee video stability and when flip, you can view video
more clearly.
This function needs speed dome driver (camera) supported.
2
2 Menu
SYSTEM
INFORMATION
PRESET TITLE
ON
(ON/OFF)
DISPLAY SET
TING
SYSTEM
CAMERA SE
TTING
FUNCTION SET
TING
EXIT
WB SETTING
PRESET
ALARM SET
TING
A
LARM NO
2.1 Screen Menu Index
Note:
ERR means current setup is invalid.
… means there is submenu.
INFORMATION
ADDR INFORMATION…
SET NORTH
LANGUAGE ：ENGLISH
FACTORY DEFAULT
RESTART
BACK
EXIT
AZIMUTH DISP : ON (ON/OFF)
POSITION : OFF (ON/OFF)
ZOOM DISP : OFF (ON/OFF)
INSIDE TEMP : ℃ (℃/F/OFF)
TITILE DISPLAY :OFF
BACK
EXIT
EXPOSURE SETTING
DAY/NIGHT SETTING
FOCUS SETUP
ZOOM SPEED
APERTURE
APERTURE CNT LEVEL
NEXT PAGE
BACK
EXIT
AUTO PAN
AUTO SCAN
TOUR
PATTERN
IDLE MOTION
NEXT PAGE
BACK
EXIT
ACTION
SN
CONTACT
RELAY OUT
RESET DELAY
SAVE
BACK
EXIT
…
:
3
The above diagram illustrates the overall structure of the speed dome setup menu.
Note:
z ERR means current setup is invalid. Please restore factory default setup.
z Please make sure all the cable connections are right.
2.2 Self-diagnosis System Information
ADDR ：001-H
BAUD RATE ：9600
PARITY ：None
SOFTWARE ：V1.02.0.R
After installation, please connect speed dome to power. The system goes on a self-diagnosis, and then
it pops up the above interface to show the system information.
The above interface disappears after speed dome received the first command (or the display time lasts
for 4 minutes.)
z ADDR: Here you can view dome address information. For example, 001-H, H is the hardware
address number, –S is software address mode.
z Baud rate: Dome communication baud rate.
z Parity: Communication parity bit format.
z Software: Dome software version.
When you are using the control keyboard or the matrix host to control the device, please make
sure the control parameter of the keyboard or the matrix host is the same with the speed dome
OSD (including address, baud rate, parity). Please make sure the cable connection is OK.
2.3 Main Menu
You can open speed dome menu via control keyboard, matrix, or speed dome control terminal.
z SYSTEM INFORMATION： Dome system information, address information, set north direction,
language, factory default setup, reboot and so on.
z DISPLAY INFORMATION: Display dome preset title, azimuth display, direction, zoom, and dome
internal temperature and etc information.
z CAMERA PARAMETERS：Display dome white balance setup, camera function setup, day/night
setup and etc.
z FUNCTION SETTING: Set preset, pan, auto scan, auto tour, auto pattern, idle motion and etc
function.
z ALARM SETTING：Set dome alarm number, action, contact, replay out, reset time, and etc.
z EXIT: Log out the system menu.
SYSTEM INFORMATION
DISPLAY SETTING
CAMERA SETTING
FUNCTION SETTING
IR LIGHT SETTING
EXIT
2.4 Menu Operation
4
In the speed dome main menu, you can use the left/right button on the keyboard or in the speed dome
terminal menu to configure the system menu. Before setup, please move the cursor to the current item
you want to configure.
z In main menu, please click confirm button to go to the sub menu or use left/right key to configure
setup.
z Use up/down button to select back option and then click confirm button to go back to the previous
menu.
z Use up/down button to select exit option and then click confirm button to log out system menu.
z All setup here will not lose when encounter power failure.
2.4.1 System Information
SYSTEM INFORMATION
ADDR INFORMATION
SET NORTH
LANGUAGE : ENGLISH
FACTORY DEFAULT
RESTART
BACK
EXIT
z INITIAL INFORMATION: Move the cursor to INITIAL INFORMATION and then click confirm button
to go to the third submenu.
z ADDR INFORMATION: Move the cursor to SITE INFORMATION and then click confirm button to go
to the third submenu.
z SET NORTH DIRECTION: Set dome benchmark direction so that you can know the angel between
the benchmark and then current location. Please move the cursor to the option and then click
confirm button until you see O.K. Now you have set north direction.
z LANGUAGE: The dome menu language. There are several languages for you to select. Please use
the left/right button on the keyboard or in the speed dome terminal menu to set.
z FACTORY DEFAULT: Restore dome factory default setup. Please move the cursor to the option
and then click confirm button until you see O.K. Now you can see the IP dome begin rebooting to
restore factory default setup.
z RESTART: Reboot the speed dome.
z BACK: Go back to the previous menu.
z EXIT: Log out system menu.
2.4.1.1 Initialization information
ADDR ： 001-H
BAUD RATE ：9600
PARITY ：NONE
SOFTWARE ：V1.03.0.R
Move the cursor to INITIAL INFORMATION and then click confirm button, you can see the above
interface.
Here you can view dome basic information.
2.4.1.2 Address Information
ADDR TYPE : SOFT
ADDR-SOFT : 1
ADDR-HARD :0
BACK EXIT
Move the cursor to SITE INFORMATION and then click confirm button.
5
z ADDR TYPE: There are two options: soft and hard. Please use the left/right button on the keyboard
or in the speed dome terminal menu to set.
z ADDR-HARD: It is an address you set in the dial switch. You can not modify it through software.
z ADDR-SOFT: You can set address via software. It is to say, you can use menu to modify dome
address. The value ranges from 0 to 255.
z BACK: Go back to the previous menu.
z EXIT: Log out system menu.
2.4.2 Display Setting
PRESET TITLE ：ON
AZIMUTH DISP ：ON
POSITION ：OFF
ZOOM DISP ：OFF
INSIDE TEMP ：OFF
TITLE DISP ：OFF
BACK EXIT
Move the cursor to DISPLAY SETUP and then click confirm button, you can go to the third submenu.
Please use the left/right button on the keyboard or in the speed dome terminal menu to set. After
completed setup, please click save button to save current setup.
z PRESET TITLE: Display dome preset title or not. Please use the left/right button on the keyboard or
in the speed dome terminal menu to set. You can go to Function Setup->Preset section to set
corresponding preset value and preset title.
z AZIMUTH DISP: Display dome current coordinates or not. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set
z POSITION: Display the angel between the benchmark and then current location. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
z ZOOM DISP: Display speed dome zoom speed value or not. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set.
z INSIDE TEMPERATURE: Display dome internal temperature or not. There are three options: ℃
/F/Off. Please use the left/right button on the keyboard or in the speed dome terminal menu to set.
z TITLE DISPLAY: Here you can set to display speed dome position information and etc. You can use
the speed dome control terminal to set the detailed title information. Please use the left/right button
to set.
z BACK: Go back to the previous menu.
z EXIT: Log out system menu.
2.4.3 Camera Setting
WB SETTING
EXPOSURE SETTING
DAY/NIGHT SETTING
FOCUS SETUP
ZOOM SPEED : 8
APERTURE : 9
APERTURE RESTRAIN : 10
NEXT PAGE
BACK EXIT
Move the cursor to CAMERA SETTING and then click confirm button, you can go to the submenu.
6
z WHITE BALANCE SETUP: Move the cursor to current option and then click confirm button, you can
go to the third menu.
z EXPOSURE SETTING: Move the cursor to current option and then click confirm button, you can go
to the third menu.
z DAY/NIGHT: Set day/night mode. Move the cursor to current option and then click confirm button,
you can go to the third menu. There are three options: auto/manual/off. Please use the left/right
button on the keyboard or in the speed dome terminal menu to set. Please make sure your product
supports this function.
z FOCUS SETUP: It is to set camera focus mode, focus limit and etc. Please use the left/right button
on the keyboard or in the speed dome terminal menu to set.
z FOCUS LIMIT: It is to set the distance between the camera and the object. It can prevent the focus
distance is too small which may result in focusing on the enclosure. At the same time, you can
change the distance to change the focus speed.
z ZOOM SPEED: The bigger the value, the faster the speed. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set.
z APERTURE: It is to adjust the lens to achieve clear video. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set.
z APERTURE CONTROL LEVEL: System can auto reduce the aperture to lower the video noise
when it is in low illumination environment. Please use the left/right button on the keyboard or in the
speed dome terminal menu to set.
z NEXT PAGE: It includes the following options: DIGITAL ZOOM, PICTURE FLIP, FREEZE
FUNCTION, CAMERA FACTORY DEFAULT SETUP, CAMERA RESTART. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.4.3.1 White Balance Setup
WB MODE ： AUTO
R GAIN ： 82
B GAIN ： 58
BACK EXIT
Move the cursor to WHITE BALANCE MODE and then click confirm button, you can go to the submenu.
z WHITE BALANCE MODE: Set white balance adjustment mode. There are several modes such as
auto, auto trace white balance, indoor, outdoor, and manual and etc. Please use the left/right button
on the keyboard or in the speed dome terminal menu to set.
z R GAIN: Before you set R GAIN option, please note the mode shall not be auto. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
z B GAIN: Before you set B GAIN option, please note the mode shall not be auto. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.4.3.2 Exposure Setting
7
AE MODE : AUTO
GAIN SETTING : 2
SHUTTER : 1/50
IRIS SETTING : 4
EXPOSURE COMP : 8
SLOW AE : 1
SLOW SHUTTER : ON
NEXT PAGE
BACK EXIT
AGC GAIN LIMIT : 2
SLOW SHUTTER LIMIT : 1/25
NOISE REDUCTION : 3
3D NOISE REDUCTION : 1
BLC : OFF
WDR ENABLE
AE RESUME TIME : 15MIN
BACK EXIT
z AE MODE: Here you can set the camera exposure mode. It includes: auto/manual/AV (iris
priority)/TV (shutter priority). Please use the left/right button on the keyboard or in the speed dome
terminal menu to set.
o Auto: It is for you to set the exposure compensation, backlight compensation (BLC),
slow shutter, wide dynamic region (WDR).
o Manual: It is for you to set the gain setting, shutter, iris setting, wide dynamic region
(WDR).
o AV: It is for you to set the exposure setting, iris setting, wide dynamic region (WDR).
o TV: It is for you to set the shutter setting, exposure compensation, wide dynamic region
(WDR).
z GAIN SETTING: Please use the left/right button on the keyboard or in the speed dome terminal
menu to set.
z SHUTTER: Please use the left/right button on the keyboard or in the speed dome terminal menu to
set.
z IRIS SETTING: Please use the left/right button on the keyboard or in the speed dome terminal
menu to set.
z EXPOSURE COM: Please use the left/right button on the keyboard or in the speed dome terminal
menu to set.
z SLOW AE: In the strong light environment, you can lower the camera exposure speed to capture
the image and enhance the definition. Please use the left/right button on the keyboard or in the
speed dome terminal menu to set.
z SLOW SHUTTER: In lower illumination environment, you can lower the cameras auto exposure
time to capture the image and enhance the definition. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set.
z NEXT PAGE: It includes: AUTO GAIN LIMIT, AUTO SLOW SHUTTER LOW LIMIT, NOISE
CONTROL, 3D NOISE REDUCTION, BLC, WDR, BACK, and EXIT. Move the cursor to the item
and then click the left/right button to set.
o AUTO GAIN LIMIT: Please click the left/right button to set.
o SLOW SHUTTER LOW LIMIT: Please click the left/right button to set.
o NOISE REDUCTION: There may noise when the camera is monitoring the low
illumination environments. You can use the digital filter to process the noise to
guarantee the clear video.
o 3D NOISE REDUCTION: It is to set the speed dome 3D noise reduction setup. Please
use the left/right button on the keyboard or in the speed dome terminal menu to set.
o BLC: It is an abbreviation for back light compensation. System can compensate the
object in the dark light to achieve a clear video. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set.
o WDR ENBALE: It is an abbreviation for wide dynamic region. Please make sure your
camera supports current function. This function can adjust the video brightness when
8
the contrast between the strong light and the dark light is too high. Move the cursor to
current item and then click the OK button to go to the fourth level menu. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
o AE resume time: Manually click the “+” and “-“button on the PTZ interface, system cam
resume previous exposure value after specified time (The exposure value does not
resume if this function is off.).
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.4.3.3 WDR
Move the cursor to WDR and then click confirm button, you can go to the submenu.
z WDR: Click Left/right button to enable/disable camera WDR function.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
WDR ：OFF
BACK EXIT
2.4.3.4 Day/Night Setting
Move the cursor to DAY/NIGHT SETTING and then click confirm button, you can go to the submenu.
z DAY/NIGHT: Please use the left/right button on the keyboard or in the speed dome terminal menu
to set. It includes: black and white/color/auto and etc.
z THRESHOLD: The speed dome can switch the day/night mode when it reached the threshold you
set here.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
DAY/NIGHT : AUTO
THRESHOD : 05
BACK EXIT
2.4.3.5 Focus Setup
z FOCUS MODE: It is to set the camera focus mode. It includes several modes such as auto, manual,
semiautomatic.
z FOCUS LIMIT: It is to set the camera focus limit. Please use the left/right button on the keyboard or
in the speed dome terminal menu to set.
z FOCUS SENSITIVITY: It is to set the camera focus sensitivity. Please use the left/right button on
the keyboard or in the speed dome terminal menu to set.
z IR LIGHT FOCUS CORRECTION: It is to set the camera IR light focus correction. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
FOCUS MODE ： AUTO
FOCUS LIMIT ： 10CM
FOCUS SENSITIVITY ： HGIH
IR LIGHT FOCUS CORRECTION ：OFF
BACK EXIT
9
2.4.3.6 Next Page
Move the cursor to NEXT PAGE and then click confirm button, you can go to the submenu.
DIGITAL ZOOM : OFF
PICTURE FLIP : OFF
FREEZE FUNC : OFF
CAMERA FACTORY DEFAULT
CAMERA RESTATRT
BACK EXIT
z DIGITAL ZOOM: You can use the left/right button to enable/disable the digital zoom function.
z PICTURE FLIP: There are two options: on/off. Please use the left/right button on the keyboard or in
the speed dome terminal menu to set.
z FREEZE FUNCTION: This function allows the system from one preset to another preset, without
showing the video during the PTZ movement. There are two options: on/off. Please use the left/right
button on the keyboard or in the speed dome terminal menu to set.
z CAMERA FACTORY DEFAULT SETTING: Move the cursor to current item and then click confirm
button to restore factory default setup.
z CAMERE RESTART: Move the cursor to current item and then click confirm button to reboot the
camera.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.4.4 Function Setting
PRESET
PAN
AUTO SCAN
AUTO TOUR
AUTO PATTERN
IDLE MOTION
NEXT PAGE
BACK EXIT
Please go back to main menu and move the cursor to FUNCTION SETTING, click confirm button. You
can see the above interface.
z PRESET: Move the cursor to PRESET and then click confirm button to go to the third submenu.
z PAN: Move the cursor to PAN and then click confirm button to go to the third submenu.
z AUTO SCAN: Move the cursor to SCAN and then click confirm button to go to the third submenu.
z AUTO TOUR: Move the cursor to AUTO TOUR and then click confirm button to go to the third
submenu.
z AUTO PATTERN: Move the cursor to PATTERN and then click confirm button to go to the third
submenu.
z IDLE MOTION: Move the cursor to IDLE MOTION and then click confirm button to go to the third
submenu.
z NEXT PAGE: It includes: PRIVACY MASKING, PTZ SPEED, SET ZERO, POWER UP, MENU
PASSWORD, MENU IDEL, PTZ AUTO STOP, and HEATER. Move the cursor to the item and then
click the confirm button to set. .
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
10
2.4.4.1 Preset Setup
Move the cursor to PRESET button and then click confirm button to go to set interface.
z PRESET NO: Please use left/right key to modify preset number. The different protocols support
different preset values.
z TITLE：Title text is the label used for you to identify the camera. System will automatically name a
title for the camera.
z SETTING: Please input preset number first and then select the monitor zone. Please move the
cursor to setting and click confirm button. The system will pop up a message: PRESET: ***. Here ***
means preset number. And the SETTING column pops up an OK. Now you successfully added a
preset. Please note, you need to enable display preset title function first (Main menu->display
setting->preset title).Repeat the above procedures to set more presets. Once you want to modify a
preset, you can input the preset number you want to modify and then follow the above steps to set
the preset. You can successfully modify a preset content.
z CALL: Here is to recall preset. Move the cursor to PRESET NO and then input corresponding preset
value. Then move the cursor to CALL and then click confirm button to go to a preset.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
For PELCO protocol user, please refer to the following special functions:
z Call preset: Call preset 28 or preset 95 to go to dome menu. Call preset 29 or preset 99 to go to
scan. Call preset 24 or preset 81 to go to pattern. Call preset 25 or preset 82 to go to tour. Call
preset 30 or preset 96 to stop scan or pattern. Call preset 31 or preset 83 to begin rotation. Call
preset 33 to enable PTZ 180 degrees rotation. Call preset 34 to set dome position as 0.
z Set preset: Set preset 26 or 92 to set scan left limit. Set preset 27 or 93 to set scan right limit. Set
preset 22 or 79 to begin record. Set preset 23 or 80 to stop record.
PRESET NO ：001
TITLE ：PRESET001
SETTING
CALL
BACK EXIT
2.4.4.2 Pan
Move the cursor to PAN button and then click confirm button to go to setup interface.
z PAN SPEED: Set dome rotation speed. Please use the left/right button on the keyboard or in the
speed dome terminal menu to set.
z RUN: Move the cursor to call item and then click confirm button. The dome begins 360 degrees
continuous rotation.
z STOP: Highlight stop item and then click confirm button. The dome stops rotation.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
PAN SPEED ：5
RUN
STOP
BACK EXIT
2.4.4.3 Scan
11
SCAN NO ： 001
SET LEFT LIMIT
SET RIGHT LIMIT
SCAN SPEED ：5
RUN
STOP
BACK EXIT
Move the cursor to SCAN button and then click confirm button.
z SCAN NO：Here is to set auto scan number. Please use the left/right button on the keyboard or in
the speed dome terminal menu to set.
z SET LEFT LIMIT：Here is to set camera left address. Click confirm button to save current setup.
z SET RIGHT LIMIT：Here is to set camera right address. Click confirm button to save current setup.
z SCAN SPEED: Please use the left/right button on the keyboard or in the speed dome terminal menu
to set.
z RUN: Please input auto scan number first, and then please move the cursor to RUN and click
confirm button to activate auto scan function.
z STOP: Here is to terminate auto scan function.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.4.4.4 Tour
TOUR NO： : 1
TOUR SETTING
DELETE TOUR
RUN
STOP
BACK EXIT
Move the cursor to highlight TOUR item and then click confirm button to go to set interface.
z TOUR NO ：Here is to ser tour number. Please use the left/right button on the keyboard or in the
speed dome terminal menu to set.
z TOUR SETTING: Move the cursor to TOUR setting item and then click confirm button. You can see
the following interface. Here you can add or remove the preset, and set the corresponding dwell
time and call speed.
NO PRESET DWELL SPEED
01 000 005 013
02 000 005 013
03 000 005 013
… … … …
32 000 005 013
BACK EXIT
DWELL: Here is t set dwell time. Please use the left/right button on the keyboard or in the
speed dome terminal menu to set.
SPEED: Here you can set the speed value.
When you move the cursor to one tour number, you can use left/right button to turn the page.
When you move the cursor to one tour number, please click confirm button to set the tour. Please use
up/down button to set preset number, dwell time and speed. Use the left/right button to go to the next
12
tour. Click confirm button you can exit the setup. After you completed the setup, move the cursor to back
button to go to the previous interface.
z DELETE TOUR：Here is to delete a tour. Input tour number in TOUR NO and then move the cursor
to DELETE TOUR, click confirm button to delete.
z CALL: Here is to activate tour. Input tour number in tour NO and highlight CALL, click confirm button
to activate tour.
z STOP: Here is to terminate touring.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.4.4.5 Pattern
PATTERN NO :1
PROGRAM START
PROGRAM STOP
RUN
STOP
BACK EXIT
Pattern function can memory PTZ operation and camera focus zoom in and zoom out.
From the start position, dome begins auto movement repeatedly.
This series IP dome supports maximum 5 patterns and one pattern can max support 400 commands.
Move the cursor to PATTERN and click confirm button.
z PATTERN NO： Here is to set pattern number. The value ranges from 1 to 5. Please click left/right
key to configure.
z PROGRAM START: Here is to memorize pattern starting point. An icon OK pops up in screen to
prompt you system begins memory pattern.
z PROGRAM STOP：Here is to set pattern stop point. After all the movement, move the cursor to
PROGRAM STOP and then click confirm button. Now you have set one pattern. System pops up an
icon OK to prompt you system has memories one pattern.
z RUN：Here is to activate pattern. Input pattern number, move the cursor to RUN and click confirm
button, system begins running pattern.
z STOP: Here is to stop current pattern. Input pattern number, move the cursor to STOP and click
confirm button. System stops current pattern.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
Note:
z The dwell time between two orders should be less than one minute, otherwise system will set to
default value as one minute.
z After click PROGRAM STOP, do not click CALL button before icon “●” disappears completely.
z Any manual operation during the pattern procedure will terminate current dome pattern operation.
2.4.4.6 Idle Motion
13
IDLE FUNC ：OFF
IDLE TIME ：10MIN
IDLE ACTION ：NONE
PARAMETER ：NONE
BACK EXIT
When there is no available command for specified time, dome automatically goes on the previous set
functions.
z IDLE FUNCTION ：There are two modes ON/OFF. Please use left/right key to set.
z IDLE TIME: System idle period. Please use the left/right button on the keyboard or in the speed
dome terminal menu to set.
z IDLE ACTION：There are several functions you can select:
NONE/PRESET/SCAN/TOURING/PATTERN. Please use the left/right button on the keyboard or in
the speed dome terminal menu to set.
z PARAMETER: It is to set idle motion SN. System can implement the corresponding action when it is
idle for the specified period. Click the left/right button to set.
z SAVE：Move the cursor to SAVE and click confirm button to save current setup.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.4.4.7 Next Page
Move the cursor to the NEXT PAGE and then click the confirm button, you can go to the third menu
to set the PTZ SPEED, POWER UP and etc.
z PRIVACY MASK: Here you can set the privacy mask number and etc. It includes the third menu.
Please move the cursor to the current item and then click the confirm button to go to the next
interface.
z PTZ SPEED: It is to set PTZ speed. Please use the left/right button to set.
z HORIZONTAL COORDINATES: Please move the PTZ to the horizontal coordinates, click OK
button to confirm.
z POWER UP: It is to set the PTZ action when the speed dome boots up. Click the confirm button to
go to the next interface to set.
z MENU IDLE: If current setup is ON, once you open the menu and leave it idle for specified period,
the menu may automatically disappear. If current setup is OFF, the menu is always there and will
not disappear. Please use the left/right button to set.
z PTZ AUTO STOP: The speed dome will stop all the PTZ operations when there is no command for
the specified time. It includes various setups. Please use the left/right button to set.
z TEMPERATURE: It includes: on/off/auto (default).
PRIVACY MASK
PTZ SPEED :2
HORIZONTAL COORDINATES
POWER UP
MENU IDLE : 1M
PTZ AUTO STOP : 15S
BACK EXIT
14
z BACK: Go back to the previous menu.
z EXIT: Log out the system menu.
Privacy Mask
Move the cursor to PRIVACY MASK and click confirm button, system goes to privacy mask setup
interface.
PRIVACY NO : 1
ACTIVATE : OFF
SETTING
BACK EXIT
RESIZE : 1
SAVE
BACK EXIT
Note:
z For security reasons, please set privacy zone a little bit larger than the privacy object size.
z Each time, after modifications you need to move the cursor to SAVE button and then click confirm
button to get all setup activated. Otherwise, privacy zone may not move correspondingly with the
object.
Please enter privacy mask menu, now all the privacy zones are closed.
Move the cursor to PRIVACY NO, please use left/right key to set different privacy zones.
For example, shift to 001 section and then move the cursor to ACTIVATE.
Secondly, click OK button to go to the setup interface. Now there is a privacy zone in the screen centre.
Thirdly, use PTZ to move camera so that privacy object fit well with screen centre.
Fourthly, move the cursor to RESIZE and then click left and right key to adjust privacy zone direction
and size.
Fifthly, move the cursor to SAVE and then click confirm button to exit.
z PRIVACY NO：Here is to set privacy mask zones. Please use the left/right button on the keyboard
or in the speed dome terminal menu to set.
z ACTIVATE: There are two settings: on and off. When activate function is on, the privacy mask
function will be activated and displays in the screen. When activate function is off, the privacy mask
function will be closed and the blank will not displayed in the screen.
z RESIZE：It is to adjust the privacy zone size. Move the cursor to current item and use the left/right
button on the keyboard or in the speed dome terminal menu to set .Please continue pressing
direction button to widen or narrow zone size. ← is to narrow the horizontal width and → is to widen
the horizontal width. ↑ is to widen vertical height and ↓ is to narrow the vertical height.
z SAVE：Here is to save user setup.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
Power Up
Move the cursor to the POWER UP item and then click the confirm button, you can go to the fourth
menu.
z POWER UP: It is to set the PTZ operation
POWER UP ：AUTO
PARAMTER ：OFF
BACK EXIT
when the speed dome boots up. The
15
option includes: NONE/AUTO/SCAN/PRESET/PATTERN/TOUR and etc. Please use the left/right
button to set.
z PARAMTER: Here you can set the serial number of the corresponding operation such as the scan,
preset, pattern, tour. Please use the left/right button to set.
z BACK: Go back to the previous menu.
z EXIT: Log out the system menu.
2.4.5 Alarm Setup
ALARM NO ：1
ACTION ：NONE
SN ： NONE
CONTACT ：N/O
RELAY OUT ：OFF
RESET DELAY ：3S
SAVE
BACK EXIT
Move the cursor to highlight ALARM SETTING button and then click confirm button.
z ALARM NO: Here is to set alarm input. Alarm input value ranges from 1 to 7. Please use the
left/right button on the keyboard or in the speed dome terminal menu to set.
z ACTION: Action on alarm function. It includes NONE/PRESET/AUTO SCAN/TOURING functions.
Please use the left/right button on the keyboard or in the speed dome terminal menu to set.
z SN: it is to set corresponding alarm operation such as scan/preset/tour. Please use the left/right
button to set.
z CONTACT：You can set system activation operation once alarm occurred. There are two alarm
signal mode: normal open (N/O) and normal closed (N/C). Please use the left/right button on the
keyboard or in the speed dome terminal menu to set.
z RELAY OUT: Here is to set relay alarm mode and reset time. There are several options: off/1→5S.
z RESET DELAY: Here is for you to set alarm reset time. Please use the left/right button on the
keyboard or in the speed dome terminal menu to set: 3 seconds/10 seconds/30 seconds/60
seconds /120seconds. The dome will go back to previous setup after alarm acknowledgement.
z SAVE：Move the cursor to SAVE and then click confirm button to save current setup.
z BACK: Go back to previous menu.
z EXIT: Log out system menu.
2.5 Dome Abnormal Phenomenon Operation
2.5.1 Restore to Factory Default Setup
From main menu-> SYSTEM INFORMATION, move cursor to FACTORY DEFAULT and click confirm
button. Dome will reboot and all the setups restore to factory default setup.
2.5.2 PTZ Movement is not smooth
From menu to SYSTEM INFORMATION, move cursor to RESTART and click confirm button. This
reboot will not modify all activated setup (such as preset, tour and pattern)
16
3 Cable Connection
The speed dome combination cable includes video cable connection port, RS485 connection port, alarm
input and output port, and power cable connection port. Please refer to the label for detailed information.
z Slight difference may be found in the port amount since some functions are optional.
Name Function
POWER
GND
485A
485B
ALARM
IN
Power port. Connect to the power cable.
GND: ground end.
RS485 remote control.
GND Video ground port. VIDEO
OUT Video output port.
z Two alarm input channels. It is to receive relay signal from the
external alarm source. You can go to dome menu to activate
specified preset or patter.
z When the activation mode is NO (normal open), speed dome
generates an alarm when alarm input port connects to the alarm
input GND port.
z When the activation mode is NC (normal close), speed dome
generates an alarm when alarm input port disconnects to the
alarm input GND port.
Note:
z Dome alarm input message is ground mode.
z Dome alarm input signal are two modes: normal open and
normal close.
GND Alarm input ground end.
ALARM
OUT
1
z One alarm output channels. When there is an alarm from current
channel, system activates relay or not.
z Alarm output relay default setup is NO.
3.1 System Layout
3.1.1 System Connection
Please refer to Figure 3-1 for system connection information.
17
Figure 3-1
Note:
Please use shielded twisted pair. The shielded layer shall connect to GND firmly; otherwise it may affect
communication or video work.
3.1.2 Alarm Connection
Please refer to Figure 3-2 for alarm connection information.
Figure 3-2
18
4 FAQ
4.1 Daily Maintenance
Please clean dome cover regularly to get vivid image.
Handle the cover with care. Use water to wash. Don’t use cloth to clean.
Use mild detergent to clean if there is too much dust.
Note:
The sweat from your hand may erode plating surface, your nail may scrape dome cover result in blur
image.
4.2 Problems and Solutions
SYMPTOM CAUSE SOLUTION
1) No self-diagnosis,
no video signal
when I connect
dome to power.
There is a noise
3) Video signal loss
occurs in high speed
rotation.
successive
6) During camera
switch, there is a tilt
movement in the
monitor.
Red LED is not on.
z Your power supplying does
not apply to the power. Or
connection is too loose.
z Power off or transformer
problem.
Red LED light on the power
board is on
z Power supplying is low
z Something wrong with power
board.
Power supplying is inadequate. Replace power supplying. 2) No self diagnosis.
Mechanical malfunction. Need electrical engineer help.
Power supplying is not sufficient Replace power supplying.
Circuit connection is too loose. Connect tightly. 4)Video signal is not
Video switch or power problem Need electrical engineer help.
Focus is in manual mode. Control manually. 5) Video is not clear.
Dome cover is dirty. Wash dome cover
Camera power is not in the same
Phase.
z Check power is connected or
properly earthed.
z Check power supply condition
or check transformer.
z Use multimeter to check
dome load.
z Please contact retailer to
replace power board.
When several domes are
connected to one transformer,
please connect the transformer
output cable to the domes’ same
side.
19
5 Appendix Ⅰ Thunder Proof and Surge Protection
This series speed dome adopts TVS lighting protection technology. It can effectively prevent damages
from various pulse signals below 1500W, such as sudden lighting and surge. While maintaining your
local electrical safety code, you still need to take necessary precaution measures when installing the
speed dome in the outdoor environment.
z The distance between the signal transmission cable and high-voltage device (or high-voltage cable)
shall be at least 50 meters.
z Outdoor cable layout shall go under the penthouse if possible.
z For vast land, please use sealing steel tube under the land to implement cable layout and connects
one point to the earth. Open floor cable layout is forbidden.
z In area of strong thunderstorm hit or near high sensitive voltage (such as near high-voltage
transformer substation), you need to install additional high-power thunder protection device or
lightning rod.
z The thunder protection and earth of the outdoor device and cable shall be considered in the building
whole thunder protection and conform to your local national or industry standard.
z System shall adopt equal-potential wiring. The earth device shall meet anti-jamming and at the
same time conforms to your local electrical safety code. The earth device shall not short circuit to N
(neutral) line of high voltage power grid or mixed with other wires. When connect the system to the
earth alone, the earth resistance shall not be more than 4Ω and earth cable cross-sectional area
shall below 25 mm2. See
Figure 5-1.
Figure 5-1
20
6 Appendix 2 Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name
Pb Hg Cd Cr VI PBB PBDE
Sheet Metal ○ ○ ○ ○ ○ ○
Plastic Parts ○ ○ ○ ○ ○ ○
PCB ○ ○ ○ ○ ○ ○
Housing
Camera Driver
○
○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
Bearing ○ ○ ○ ○ ○
Connection
Cable
Motor
(If possible)
Power
(If possible)
Bracket
(If possible)
Accessories ○ ○ ○ ○ ○ ○
Note
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes.
○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○
○
21
Note
• This manual is for reference only. Slight difference may be found in the user interface.
• All the designs and software here are subject to change without prior written notice.
• All trademarks and registered trademarks mentioned are the properties of their respective
owners.
• If there is any uncertainty or controversy, please refer to the final explanation of us.
• Please visit our website or contact your local service engineer for more information.
22
Loading...