ICPDAS PCI-P16C16U Quick Start Manual

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.

1

Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]

The shipping package includes the following items:

Note: For more details regarding the Card ID and Jumper settings, refer to the PCI-P16C16

Series User Manual.

For PCI-P16C16U

Check the Supplied Items

English/Oct. 2015/Version 1.0

Software Utility CD

(V6.2 or later)

Quick Start Guide
(This Document)

PCI-P16C16U

CA-4002 D-Sub

Connector x 2

CA-4037W

Cable x 1

Board Layout











1. CN1 Connector

(See Section 5 Pin Assignments)

2. CN2 Connector

(See Section 5 Pin Assignments)

3. SW1: Card ID Switch

(The default setting is 0x0.)

4. JP1 ~ JP8, JP9 ~ JP16: Input

Signal Type Jumper

5. J1, J2: Set the Ground Isolation

Protection

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.

2

Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]

The UniDAQ driver supports Windows 2000 and 32/64-bit versions of Windows

XP/2003/2008/7/8. The driver installation package for PCI-FC16U board can be found on

the companion CD-ROM, or can be obtained from the ICP DAS FTP web site. The driver

is located at:

CD: \NAPDOS\PCI\UniDAQ\DLL\Driver

http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/

To install the UniDAQ driver, follow the procedure described below.

Step 1: Double-click the UniDAQ_Win_Setupxxx.exe icon to begin the installation

process.

Step 2: When the “Welcome to the ICP DAS UniDAQ Driver Setup Wizard” screen

is displayed, click the “Next>” button to start the installation.

Step 3: On the “Information” screen, verify that the DAQ card is included in the list of

supported devices, then click the “Next>” button.

Step 4: On the “Select Destination Location” screen, click the “Next>” button to install

the software in the default folder, C:\ICPDAS\UniDAQ.

Step 5: On the “Select Components” screen, verify that the DAQ Card is in the list of

device, and then click the “Next>” button to continue.

Step 6: On the “Select Additional Tasks” screen, click the “Next>” button.

Step 7: On the “Download Information” screen, click the “Next>” button

Step 8: Once the installation has completed, click “No, I will restart my computer later”,

and then click the “Finish” button.

Note: For detailed information about the driver installation, refer to Chapter 2 “Install

UniDAQ Driver DLL” of the UniDAQ SDK User Manual.

Installing the Windows Driver

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.

3

Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]

Step 1: Shut down and power off the computer.

Step 2: Remove all the covers from the computer.

Step 3: Select an unused PCI slot.

Step 4: Carefully insert the PCI-P16C16U board into the

PCI slot and secure the board in place.

Step 5: Replace the covers on the computer.

Step 6: Reconnect the power supply and power on the

computer.

Step 7: Once the computer reboots, follow any messages that may be displayed to

complete the Plug and Play installation procedure.

Step 8: Open the “Device Manager” in the Control Panel and verify that the

PCI-P16C16U board is listed correctly, as illustrated below.

Installing the Hardware

Installation successful

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.

4

Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]

Pin Assignments

Extension Cable (CA-4037W):
Conversion from DB-40-pin to DB-37-pin

Notes:

Ext. Power:

External Power Input

GND:

External Power Ground

OUT:

Open Collector Output

DIA:

Digital Input (Point A)

DIB:

Digital Input (Point B)

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.

5

Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]

 Wiring for the Digital Input/Output Test:

Step 1: Connect the DN-37 to the CN1 connector on the board using the CA-3710 cable.

Step 2: Connect the CN1.OUT0 pin (Pin 1) to the CN1.DIA0 pin (Pin12).

Step 3: Connect the External Power Supply GND to the CN1.GND1 pin (Pin22) and

CN1.GND2 pin (Pin26).

Step 4: Connect the External Power Supply +24V to the CN1.Ext.Power1 pin (Pin20)

and CN1.DIB0 pin (Pin30).

Self-Test

PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.

6

Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]

 Execute the UniDAQ Utility Program:

Step 1: In Windows 7, click the “Start” button,

point to “All Programs”, and then click the

“ICPDAS” folder. Point to “UniDAQ

Development Kits”and then click the “UniDAQ

Utility” to execute the UniDAQ Utility Program.

Step 2: Confirm that the PCI-P16C16U board has

been successfully installed in the Host system.

Note that the device numbers start from 0.

Step 3: Click the “TEST” button to start the test.

Step 4: Check the results of the Digital Input/Output functions test.

1. Click the “Digital Output” tab.

2. Select “Port0” from the “Port Number” drop-down menu.

3. Check the checkboxes for channels 0.







PCI-P16C16U Quick Start Guide ICP DAS CO., LTD.

7

Website: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]

4. Click the “Digital Input” tab.

5. Select “Port0” from the “Port Number” drop-down menu.

6. The DI indicators will turn red when the corresponding DO channel 0 is ON.

 PCI-P16C16U Series Board Product Page:

http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-p16c16.html

 DN-37, DB-665 and CA-3710 Product Pages (optional):

http://www.icpdas.com/root/product/solutions/pc_based_io_board/daughter_boards/dn

-37.html

http://www.icpdas.com/root/product/solutions/accessories/power_supply/dp-665.html

http://www.icpdas.com/products/Accessories/cable/cable_selection.htm

 UniDAQ Documentation and Software:

CD:\NAPDOS\PCI\UniDAQ\

http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/

Related Information





