- 1 -
Language English
Version V1.3
Update Feb.2009
………………………………………………
What’s on your package?
¾ One ISO-C64 series card
¾ One companion ISA CD (V2.1 or later)
¾ One Quick Start Guide(This document)
………………………………………………
Installing Windows Driver
Follow those steps:
1. Setup the Windows driver. You can get the driver from:
CD:\NAPDOS\ISA\ISO\DLL\
http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/iso/dll/
2. Click “Next >” button to start installation.
3. Click “Next >” button to install driver into the default folder.
4. Click “Install” button to continue installation.
5. Select “NO, I will restart my computer later” and click “Finish”.
1
2
I
SO
-
C
6
4
Windows driver only support windows 98/NT/2000 and
XP/2003/vista 32-bit versions.
- 2 -
………………………………………………
I/O Base Address
¾ The base address is set from SW1 DIP switch on
board:
………………………………………………
Installing Hardware on PC
Follow those steps:
1.
Shut down and power off your computer
2. Remove all covers from the computer
3. Select an empty ISA slot
4. Carefully insert your I/O card into the ISA slot
5. Replace the PC covers
6. Power on the computer
After powering-on the computer, continue next process.
3
4
ON
1 2 3 4 5 6
SW1: Base Address
* Default Base Address: 0x200
Address 1 2 3 4 5 6
*0X200 ON ON ON ON ON ON
0X208 ON ON ON ON ON OFF
0x210 ON ON ON ON OFF ON
0x218 ON ON ON ON OFF OFF
0x220 ON ON ON OFF ON ON
: : : : : : :
0x300 OFF ON ON ON ON ON
0x308 OFF ON ON ON ON OFF
0x310 OFF ON ON ON OFF ON
: : : : : : :
- 3 -
………………………………………………
Adding Hardware
7. Add Hardware
7-1 Open the “Control Panel” by click the item “Start / Settings / Control
Panel”.
7-2 Double-click the item “Add/Remove Hardware”
and click “Next >” button.
7-3 Select the item “Add/Troubleshoot a device”
and click“Next >” button.
7-4 Select the item “Add a new device”
and click “Next >” button.
7-5 Select the item “No, I want to select the hardware from a list”
and click
“Next >”
button.
7-6 Select the item “Other device”
and click “Next >” button.
7-7 Click the “Have Disk…”
button.
7-8 Click the “Browse…”
button to select the Inf file default path is
C:\DAQPRO\ISO_Win2K\Inf and clicks the “OK”
button.
7-9 Select the correct device from the “Models:”
listbox and Click “Next >”
button.
7-10 The windows show to dialog box and Click the “OK”
button to enter the
device’s properties settings.
8. Modify the device properties
8-1 Enter the “ICPDAS ISO-P64/ISO-C64 Digital I/O Card Properties”.
8-2 Click the “ I/O Range ”
and click the “Change setting” button to enter the
“Edit Input/Output Range”.
8-3 Set the I/O Range value for SW1 value. (Default 200 Hex)
8-4 Check the Conflict information for “ No devices are conflicting”
and click
“OK”
.
9. Reboot the PC
The detail “add hardware” information. Please refer to :
CD:\NAPDOS\ISA\Manual\PCI_ISA_PnP_Driver_Installation_in_Win9x_2K_XP.pdf
5
Adding hardware is used on Windows 2000/XP/2003/Vista
32 only. Windows 9X/Me/NT users can skip it.
Loading...