Page 1
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
FSM-510G Series
Ethernet Management Switch
Quick Start Guide
Overview
The Management Ethernet Switch solutions are designed for supporting standard
industrial applications. Managed switches are easily to prioritize partition and
organize user’s network and provide reliable and good quality services.
The switch can be managed through RS-232 serial port via direct connection, or
through Ethernet port using Telnet or Web-Based management unit, associated with
SNMP agent. With the SNMP agent, the network administrator can log on the switch
to monitor, configure and control each port activity in a friendly way. The overall
network management is enhanced and the network efficiency is also improved to
accommodate high bandwidth applications. The switch features comprehensive and
useful functions such as QoS (Quality of Service), Spanning Tree, VLAN, Port
Trunking, Bandwidth Control, Port Security, SNMP/RMON.
Models
L2+ Managed Switch
FSM-510G-2F
FSM-510G-4F
Total GE Ports
10 10
10/100/1000
8
6
BaseT(X)
100/1000 Base SFP 2 4
Safety Instructions
When a connector is removed during installation, testing, or servicing, or when an
energized fiber is broken, a risk of ocular exposure to optical energy that may be potentially
hazardous occurs, depending on the laser output power.
The primary hazards of exposure to laser radiation from an optical-fiber
communication system are:
Damage to the eye by accidental exposure to a beam emitted by a laser source.
Damage to the eye from viewing a connector attached to a broken fiber or an
energized fiber.
Page 2
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
Specifications
Model
FSM-510G Series
Ethernet
Copper RJ45 Ports
10/100/1000 Mbps speed auto-negotiation
MDI/MDIX Auto-crossover
SFP (pluggable)
100/1000Base SFP slot
Ports
Fiber port connector
LC typically for fiber (depends on module)
Power
Power input
Redundant Input Terminals; Reverse power protection
Input voltage range
+12-48 VDC
Maximum Power
10.5W
consumption
Environmental and Compliances
Operating
-40 to +75°C
temperature
Storage temperature
-40 to +85°C
Humidity
5 to 95% RH (non-condensing)
Mechanical
Ingress protection
IP30
Dimension
154mm(H) x 109mm(L) x 60mm(W)
(without DIN rail clip)
Installation option
DIN-Rail mounting
Wall mounting
Page 3
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
Faceplate
10-Port series
DIN-Rail Mounting
Mounting step:
1. Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
2. Hook the unit over the DIN rail.
3. Push the bottom of the unit towards the DIN Rail until it snaps into place.
Page 4
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
1
2
Wall Mounting
Mounting step:
1. Screw on the wall-mount plate on with the plate and screws in the accessory kit.
The graph is for all series
Page 5
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
Ethernet Interface Connecting (RJ45 Ethernet)
The switches provide two types of electrical (RJ45) and optical (mini-GBIC) interfaces.
Connecting the Ethernet interface via RJ45:
To connect to a PC, use a straight-through or a cross-over Ethernet cable,
To connect the FSM-510G switch to an Ethernet device, use UTP (Unshielded TwistedPair)
or STP (Shielded Twisted Pair) Ethernet cables.
The pin assignment of RJ-45 connector is shown in the following figure and table.
Pin
Assignment
1,2
T/Rx+,T/Rx-
3,6
T/Rx+,T/Rx-
4,5
T/Rx+,T/Rx-
7,8
T/Rx+,T/Rx-
Ethernet Interface Connecting (Fiber, SFP)
For a 100 Mbps fiber port available, please prepare the LC connectors or SC
connectors (with the use of an optional SC-to-LC adapter).
For a 1000 Mbps fiber port available, please use the mini-GBIC SFP. These accept plug
in fiber transceivers that typically have an LC style connector.
They are available with multimode, single mode, long-haul or special-application
transceivers.
DANGER: Never attempt to view optical connectors that might be emitting laser energy.
Do not power up the laser product without connecting the laser to the optical
fiber and putting the cover in position, as laser outputs will emit infrared
laser light at this point.
Page 6
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
Power Connecting
The switch can be powered from two power supply (input range 12V – 58V). Inser t the
positive and negative wires into V+ and V- contact on the terminal block and tighten
the wire-clamp screws to prevent the wires from being loosened.
Note: 1. The DC power should be connected to a well-fused power supply.
First Power Supply
Second Power Supply
Alarm Relay and Ground Connecting
The alarm relay output contacts are in the middle of the DC terminal block connector
as shown in the figure below.
By inserting the wires and set the DIP switch of the respective Port Alarm to “ON”, the
relay output alarm will detect any port failures, and form a short circuit.
The alarm relay out is “Normal Open”.
Ground Connector
Page 7
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
7
Console Connection
The Console port is for local management by using a terminal emulator or a computer
with terminal emulation software.
DB9 connector connect to computer COM
port Baud rate: 115200bps
8 data bits, 1 stop
bit None Priority
None flow control
To connect the host PC to the console port, a RJ45 (male) connector-to-RS232 DB9
(female) connector cable is required. The RJ45 connector of the cable is connected to the
CID port of IVS-500; the DB9 connector of the cable is connected to the PC COM port. The
pin assignment of the console cable is shown below:
Page 8
FSM-510G Ethernet Management Switch - QuickStart (Aug/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1 -310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
8
Connect & Login to FSM-510G
1. Connecting to FSM-510G Ethernet port (RJ45 Ethernet port).
2. Factory default IP: 192.0.2.1
3. Login with default account and password.
Username: admin
Password: (none)
CLI Initialization & Configuration (Optional)
1. Connecting to FSM-510G Ethernet port(RJ45 Ethernet port)
2. Key-in the command under Telnet: telnet 192.0.2.1
3. Login with default account and password.
Username: admin
Password: (none)
4. Change the IP with commands listed
below: CLI Command:
enable
configure terminal
interface vlan 1
ip address xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
exit
LED STATUS INDICATIONS
LED Name
Indicator /color
Condition
P1/P2
On Green
P1/P2 power line has power
Off P1/P2 power line disconnect or does not have supply power
Alarm
On Red
Ethernet link fail alarm or power failure alarm occurs
Off No Ethernet link fail and no power failure alarm
Copper port
On Green
Ethernet link up but no traffic is detected
Flashing Green
Ethernet link up and there is traffic detected
Link/Act
Off Ethernet link down
Copper port
On Yellow
A 1000Mbps connection is detected
Speed
Off No link, a 10Mbps or 100 Mbps connection is detected
SFP port
On Green
Ethernet link up
Link/Act
Off Ethernet link down
SFP port
On Yellow
SFP port speed 1000Mbps connection is detected.
Speed
Off No link or a SFP port speed 100Mbps connection is detected
Loading...