ICP TSTAT0406, TSTAT0407 Installation Instructions & User Manual

Download

Page 1

TSTAT0406 & TSTAT0407

997-060180-5

Installation Instructions / User’s Manual

TSTAT0406 and TSTAT0407 4 HEAT – 2 COOL – DUAL FUEL

TSTAT0406 & TSTAT0407 - 4 WIRE CAPABLE THERMOSTAT (NAXA00101DB Daughter Board sold separately)

LEFT OR PREVIOUS

SCREEN BUTTON

SELECT BUTTON

DOWN BUTTON

Apply logo label here

THERMOSTAT BUTTON OPERATION

UP BUTTON

RIGHT BUTTON

Menu Driven Display

NOTE: You must go through the Model Configuration menus first. If you do not configure your thermostat and go straight to the different modes you will get a “Configuration Error” code flashing at the top of the screen. To void error, run through the Configuration Mode Menus. To Enter Configuration Menu set mode to OFF, then push the up and down buttons simultaneously for 5 seconds.

International Comfort Products, LLC Page 1 48201530101 Sep 2008

Page 2

TSTAT0406 & TSTAT0407

TSTAT0406 AND TSTAT0407 MENU MAP

INSTALLER

SETTINGS

MAIN SCREEN

MODEL

CONFIGURATION HEAT/COOL SINGLE STAGE ELECTRIC

MULTI STAGE ELECTRIC

HEAT PUMP SINGLE STAGE ELECTRIC

MULTI STAGE ELECTRIC

ACCESSORIES AIR FILTER CUMULATIVE RUN TIME HOURS

HUMIDIFER CUMULATIVE RUN TIME HOURS

UV LAMP CUMULATIVE RUN TIME HOURS

ELEC. AIR CLEANER CUMULATIVE RUN TIME HOURS

INPUT DEALER INFO BRAND NAME

FAN WITH HEAT

OPTION

HUMIDITY OPTION

(HUMIDITY SETTINGS) HUMIDIFY ONLY

RESTORE DEFAULTS

OFFSETS TEMPERATURE OFFSETS TEMPERATURE OFFSET

CYCLES PER HOUR

PROGRAM SETTINGS SMART RECOVER

SERVICE

INFORMATION FAULT STATUS

DOWN STAGING

TEST MODE

COOL TO DEHUMIDIFY

RH (RELATIVE

HUMIDITY)

TEMP

MODE (OPERATING

MODE)

FAN

MENU (MAIN MENU) SET DATE AND TIME AUTO DAYLIGHT SAVING

FURNACE MODEL

NUMBER

HP MODEL NUMBER

CONTRACTOR NAME

CONTRACTOR PHONE

SMART HEAT STAGING

ELECTRIC/FUNRACE

FAULT CODE DEFINITION FLASH CODE 1-9

CLEAR FAULT HISTOR

DISPLAY DEALER INFO

SETTINGS (SETTING

SECURITY LOCKOUT TEMP ADJUST ONL

SAVE YOUR DEALER IS

DEHUMIDIFY ONL

AUTO

NONE

HUMIDITY OFFSET

ANTICIPATOR

EVENTS PER DAY

COOLING LOCKOUT

LOCKOUT

BALANCE POINT

HOLD (HOLD MENU) VACATION HOLD

PROGRAM MENU

MODE (OPERATING

FAN

MODE)

DISPLAY HUMIDIT

MENU) SCREEN SETTINGS FAHRENHEIT OR CELSIUS

CALENDER TIME MONTHS

REMOTE INDOOR

OFFSET

OUTDOOR OFFSET

SET DATE AND TIME

PERMANENT HOLD

PROGRAMMING

SCREEN

AUTO CHANGEOVER AUTO CHANGEOVER TIME

INTERMITTENT FAN INTERMITTEN FAN OFF TIME

TOTAL KEYPAD

LOCKOUT

MONTH/DAY/YEAR/HOUR/MINUTE

AUTO OR MANUAL CHANGE

DUAL FUEL

DAY/TIME

12 OF 24 HOUR CLOCK

LANGUAGE CONTRAST

BACKLIGHT ON TIME

GAS

International Comfort Products, LLC Page 2 48201530101 Sep 2008

Page 3

TSTAT0406 & TSTAT0407

Heat Cool / Heat Pump / Dual Fuel Communicating Thermostat

Installation and Start-up Instructions

INSTALLER SETTINGS

MODEL CONFIGURATION

MODEL CONFIGURATION ACCESSORIES INPUT DEALER INFO FAN WITH HEAT OPTION HUMIDITY OPTION RESTORE DEFAULTS OFFSETS CYCLES PER HOUR PROGRAM SETTINGS SERVICE INFORMATION DOWNSTAGING TEST MODE COOL TO DEHUMIDIFY

SELECT OPTION ∇? ? PREVIOUS

HUMIDITY OPTION – In thermostats with an internal humidity sensor (TSTAT0407) this determines if humidification or dehumidification will be energized. (Not shown on systems without humidity sensor) RESTORE DEFAULTS – This will restore all factory defaults. OFFSETS – Allows setting of permanent offsets to the temperatures and humidity to compensate for room differences or measurement differences. CYCLES PER HOUR – limits the cycling of the system to a set maximum per hour to reduce short cycling and extend system life. PROGRAM SETTINGS – Sets custom operation of the programming feature.

DOWN STAGING – You can turn down staging on or off. Default is on.

TEST MODE – Allows forced operation of all the different heating and cooling modes of the thermostat based on

The model configuration selected. Also shortens or eliminates the short cycle timer.

MODEL CONFIGURATION

HEAT / COOL

HEAT PUMP

SELECT OPTION ∇∆ ⊲ PREVIOUS

MODEL CONFIGURATION

SINGLE STAGE

MULTI STAGE

MULTISTAGE

SELECT OPTION ∇∆ ⊲ PREVIOUS

International Comfort Products, LLC Page 3 48201530101 Sep 2008

To enter the INSTALLER SETTINGS screen, the thermostat MUST be in the OFF mode and at the MAIN SCREEN press and hold the UP and DOWN buttons at the same time for 5 seconds. This will bring up the INSTALLER SETTINGS screen. The installer settings are options that are specific to a particular installation and should only be adjusted by qualified service personnel.

The INSTALLER SETTINGS options are:

MODEL CONFIGURATION – Defines what type of system the thermostat is controlling. ACCESSORIES – What else is attached to the system and sets service alerts. INPUT DEALER INFO – Allows service personnel to enter their name, phone number, and model information for display in service situations. FAN WITH HEAT OPTION – In a gas furnace application, this option turns the G output on when the heat is on

or off. G is default to ON when electric heat is selected.

SERVICE INFORMATION – This menu can bring up current faults along with last three faults of the Comfort Alert diagnostic module. It also has a list of fault code definitions and a method of clearing the faults out of the thermostat memory.

(Refer to down staging section for details)

Staging Properties: Thermostat models TSTAT0406 & TSTAT0407 use advanced logic to control a two-stage

heating or cooling system for better home comfort and higher efficiency. The thermostat continuously monitors set point, room temperature, anticipator setting, and temperature rate-of-change. Considering all the conditions, the thermostat decides which stage (high or low) the system should be running for better home comfort and higher efficiency. It is possible that the thermostat will keep the system running for longer periods of time in low stage. This is normal, as the thermostat works to achieve higher efficiency and better home comfort. The advanced logic operates in all modes and controls the system for ramp up (off→low stage→high stage) and ramp down (high stage→low stage→off). There are NO differentials (dead bands) to set. Simply enter your desired room temperature and the thermostat will hold the room temperature to within ¼ ºF from setpoint.

COOL TO DEHUMIDIFY – Uses the HVAC equipment in cooling to dehumidify the conditioned space. This

feature is used when the system does not have variable speed capabilities.

Highlighting MODEL CONFIGURATION, in the INSTALLER SETTINGS screen, and pressing SELECT button will bring up the first MODEL CONFIGURATION screen.

The first option asks if the system is a HEAT PUMP or a HEAT/COOL system. Highlighting the proper configuration and pressing SELECT sets up the system and brings up the next configuration screen.

Highlighting the proper setting for single stage systems or multi stage systems and pressing the SELECT button sets the system for the proper operation.

If the system is configured for HEAT/ COOL operation and single or multi stage the next menu, ELECTRIC or GAS, is where you will choose your source of heat. By pressing the SELECT button you will return the display to the INSTALLER SETTINGS screen.

NOTE: If you have selected furnace and you wish to have G energized along with W you must turn the Fan

with Heat option to on.

If the system is configured for HEAT PUMP operation and single or multi stage the next menu, ELECTRIC or DUAL FUEL, is where you will choose your source of heat. For HEAT PUMP systems, the ELECTRIC OR DUAL FUEL configuration screen allows setting for gas or electric furnaces. If the auxiliary heat system is

Page 4

TSTAT0406 & TSTAT0407

MODEL CONFIGURATION

ELECTRIC

DUAL FUEL

MULTI FUEL

SELECT OPTION ∇∆ ⊲ PREVIOUS

gas or oil, highlight the DUAL FUEL option. For electric add-on heat, highlight ELECTRIC. Pressing the SELECT button finishes the system configuration and returns the display to the INSTALLER SETTINGS screen.

NOTE: The configuration steps must be done at the initial installation of the thermostat or

CONFIGURATION ERROR will appear on the top line of the MAIN SCREEN.

NOTE: YOU MUST HAVE AN OUTDOOR SENSOR FOR A DUAL FUEL SYSTEM TO OPERATE

CORRECTLY.

ACCESSORIES

AIR FILTER

HUMIDIFIER UV LAMP AIR CLEANER

Highlighting the ACCESSORIES option in the INSTALLER SETTINGS screen and pressing SELECT will bring up the ACCESSORIES screen. This allows identification of add on accessories and sets a service schedule for them.

Highlighting an accessory and pressing SELECT will bring up the NOTIFICATION METHOD screen.

SELECT OPTION ∇∆ ⊲ PREVIOUS

AIR FILTER CHANGE

CUMULATIVE RUN TIME

CALENDAR TIME

This screen allows selection of notification by elapsed time (Calendar) or by hours actually run (CUMULATIVE RUN TIME)

Highlighting CUMULATIVE RUN TIME and pressing the SELECT button will bring up the RUN HOURS SCREEN.

SELECT OPTION ∇∆ ⊲ PREVIOUS

AIR FILTER CHA NGE

CUMULATIVE RUN TIME

1000

HOURS

CHANGE SETTING ∇∆ ⊲ PREVIOUS

AIR FILTER CHANGE

CALENDAR TIME

12 MONTHS

CHANGE SETTING ∇∆ ⊲ PREVIOUS

Thi t ti i id d i t d fid ti lt UTEl t i C t l I d

Thi t ti i id d i t d fi d ti lt UT El t i C t l I d

The thermostat will keep track of the hours the system is actually running and compare that number to the numbers of hours set in the CUMULATIVE RUN HOURS screen. When the hours are met, the thermostat will display a message on the top line of the MAIN screen. In the case of the AIR FILTER, the message will say CHANGE AIR FILTER. (See MAIN SCREEN _ TOP LINE for other messages)

Use the UP and DOWN buttons to set the hours from OFF to the maximum time allowed. (See defaults table for values)

Press the SELECT button to activate and save the settings. The thermostat will automatically return the display to the ACCESSORIES screen.

Highlighting the CALENDER TIME option and pressing the SELECT brings up the CALENDER TIME screen.

Use the UP and DOWN buttons to change the Calendar time before an alert is set. The time can be set from OFF to the maximum time for the particular accessory. When the desired time is displayed, press the SELECT button to activate and save the setting. The thermostat will automatically return the display to the ACCESSORY screen.

INPUT DEALER INFO

BRAND NAME

BRAND NAME FURNACE MODEL NUMBER HP MODEL NUMBER CONTRACTOR NAME CONTRACTOR PHONE SERIAL NUMBER SAVE

SELECT OPTION ∇∆ ⊲ PREVIOUS

International Comfort Products, LLC Page 4 48201530101 Sep 2008

DEALER INFO IS:

BRAND NAME:

XXXXXXXXXXXXXXXXXXXXX

FURNACE MODEL NUMBER:

XXXXXXXXXXXXXXXXXXXXX

HP MODEL NUMBER:

XXXXXXXXXXXXXXXXXXXXX

CONTRACTOR NAME:

XXXXXXXXXXXXXXXXXXXXX 260-555-5555

SERIAL NUMBER:

XXXXXXXXXXXXXXXXXXXXX

⊲ PREVIOUS

Highlighting INPUT DEALER INFO and pressing SELECT brings up the DEALER INFORMATION screen. The options are: BRAND NAME FURNACE MODEL NUMBER HEAT PUMP MODEL NUMBER CONTRACTOR NAME CONTRACTOR PHONE SERIAL NUMBER

SAVE

Page 5

TSTAT0406 & TSTAT0407

DEALER INFO

MODEL NUMBER

USE ∇∆ TO SCROLL THRU CHARACTERS

_____________________________

CHANGE LETTER ∇∆ ⊲ PREVIOUS

Highlighting the type of information to enter and pressing SELECT button brings up the DATA ENTRY

screen for that option. Use the UP and DOWN buttons to scroll through the letters and numbers and use the RIGHT button to move to the next space. When all desired information is entered, press the SELECT button to save and return to the DEALER INFORMATION screen. When all desired dealer information has been entered, highlight the SAVE option and press the SELECT button.

The screen will display all of the entered information. If changes are needed, pressing the LEFT button will return the display to the DEALER INFORMATION SCREEN and corrections can be made. Use the RIGHT button to move across the line without changing the previous information. If changes are not necessary, press the SELECT button when the information is displayed and the display will return to the INSTALLER SETTINGS screen.

FAN WITH HEAT OPTION

FAN ON WITH HEAT OPTION

OFF

SELECT OPTION ∇∆ ⊲ PREVIOUS

HUMIDITY OPTION (HUMIDITY SETTINGS) – TSTAT0407 Model Only

SCREEN SETTINGS

HUMIDIFY ONLY

HUMIDIFY ONLY DEHUMIDIFY ONLY AUTO NONE

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the FAN WITH HEAT OPTION in the INSTALLER SETTINGS screen and pressing the SELECT button will bring up the FAN WITH HEAT screen. Highlighting the ON option and pressing the SELECT button will activate this option. When FAN WITH HEAT is active, the thermostat will turn on the fan output (G) whenever there is a call for heat. Without this option active, there is no call for FAN (G) when heat is on and the thermostat is configured for Gas heat. There is always a FAN (G) output when there is a Y output in Heat Pump applications and when the system is configured for electric heat.

Highlighting the HUMIDITY OPTION in the INSTALLER SETTINGS screen and pressing the SELECT button will bring up the HUMIDITY SETTINGS screen. The humidity options are: HUMIDIFY ONLY – Used when only a humidifier is attached to the system DEHUMIDIFY ONLY – Used when only a dehumidifier is attached to the system or the system has self dehumidification capability. AUTO – Allows for H output to be active for humidification in heating and dehumidification in cooling. The humidify set point will only be displayed in heating mode and the dehumidify set point will only be displayed in cooling mode. NONE – Used when no humidifier or dehumidifier is attached.

The settings for operation of the attached equipment are accessed from the MAIN screen by highlighting the RH option and pressing the SELECT button. To have the humidity displayed on the main screen select MENU/DISPLAY HUMIDITY from the main screen.

RESTORE DEFAULTS

YES

SELECT OPTION ∇∆

⊲ PREVIOUS

Highlighting The RESTORE DEFAULTS option in the INSTALLER SETTINGS screen and pressing the SELECT button will bring up the RESTORE DEFAULTS screen. By using the UP and DOWN buttons to highlight the YES option and pressing the SELECT button, all settings are returned to factory default condition.

NOTE: The configuration settings – HEAT COOL/HEAT PUMP, SINGLE/MULTI, GAS/ELECTRIC are NOT

reset by this command. The thermostat keeps the last valid settings. If these need to be changed, it must be done through the CONFIGURATION screen.

OFFSETS

Highlighting the OFFSETS option in the INSTALLER SETTINGS screen and pressing the SELECT button will bring up the OFFSETS SCREEN. Offsets are used when the temperature on the thermostat is not

TEMPERATURE OFFSETS

TEMPERATURE OFFSET HUMIDITY OFFSET ANTICIPATOR

representative of the room temperature the system is controlling. This may be due to many factors including position of the thermostat, room air flow, sunlight on the thermostat and others. The OFFSET options are: TEMPERATURE OFFSETS – This can apply an offset of +- 5 degrees to change the temperature reading from the internal temperature sensor, the external temperature sensor, and the outdoor temperature sensor.

SELECT OPTION ∇∆ ⊲ PREVIOUS

HUMIDITY OFFSET – This can apply an offset of +- 5% to the relative humidity read from the internal sensor ANTICIPATOR – This can be set from 0 to 4 and adjusts the sensed temperature with running time to help prevent overshoot in temperature regulation.

International Comfort Products, LLC Page 5 48201530101 Sep 2008

Page 6

TSTAT0406 & TSTAT0407

TEMPERATURE OFFSETS

TEMPERATURE OFFSET

TEMPERATURE OFFSET REMOTE INDOOR OFFSET OUTDOOR OFFSET

TEMPERATURE OFFSET

0°

Highlighting the TEMPERATURE OFFSETS and pressing SELECT will bring up the TEMPERATURE OFFSET screen. Selecting which offset to adjust and pressing SELECT will bring up the appropriate screen for the adjustment. Pressing the UP and DOWN buttons will change the offset. Pressing the SELECT button applies the offset to the temperature selected.

SELECT OPTION ∇∆ ⊲ PREVIOUS

CHANGE SETTING ∇∆ ⊲ PREVIOUS

HUMIDITY OFFSETS – Model TSTAT0407 Only

HUMIDITY OFFSET

CHANGE SETTING ∇∆ ⊲ PREVIOUS

ANTICIPATOR

SET ANTICIPATOR

CHANGE SETTING ∇∆ ⊲ PREVIOUS

CYCLES PER HOUR

MAXIMUM ALLOWED

CHANGE SETTING ∇∆ ⊲ PREVIOUS

PROGRAM SETTINGS

SMART RECOVERY EVENTS PER DAY

EVENTS PER DAY

SMART HEAT STAGING COOLING LOCKOUT ELECTRIC HEAT LOCKOUT BALANCE POINT

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the HUMIDITY OFFSET option and pressing SELECT will bring up the HUMIDITY OFFSET

screen. Pressing the UP and DOWN buttons will change the humidity value displayed and used in

thermostats equipped with an internal humidity sensor. Pressing the SELECT button will apply the offset to

the humidity.

Highlighting the ANTICIPATOR and pressing the SELECT button in the OFFSETS screen will bring up the

SET ANTICIPATOR screen. The anticipator can be adjusted from 1 to 9. The 9 setting adjusts the most.

This adjustment is applied is systems where the room temperature overshoots the set temperature at turn

off of the system. The UP and DOWN buttons will adjust the ANTICIPATOR and the SELECT button will

apply the setting.

Highlighting the CYCLES PER HOUR option and pressing the SELECT button will bring up the CYCLES

PER HOUR screen.

Pressing the UP and DOWN buttons can adjust the CYCLES PER HOUR to either 4 or 6. If set to 4 the

thermostat will not allow a cycle to start until 15 minutes have passed from the start of the last cycle.

Setting to 6 will make the system wait 10 minutes before starting the next cycle. The time is measured

from start of a cycle to the start of the next cycle, and not the off time between cycles.

Highlighting the PROGRAM SETTINGS option in the SETTINGS screen and pressing SELECT will bring

up the PROGRAM SETTINGS screen.

The PROGRAM SETTINGS options are:

SMART RECOVERY – The thermostat looks ahead to the next programmed time and temperature and

adjusts its operation to reach the desired temperature at the programmed time. The normal operation is to

change the set point at the set time and let the system adjust the temperature starting at the set event time.

EVENTS PER DAY – Sets the number of programmed events per day to either 2 or 4.

NOTE: OUTDOOR SENSOR REQUIRED FOR NEXT THREE SETTINGS

COOLING LOCKOUT – Does not allow cooling when the outside temperature is below a specified

temperature

ELECTRIC HEAT LOCKOUT/FURNACE LOCKOUT when configured for MULTI FUEL – Does not allow electric heat on a heat pump system or furnace to come on when the outdoor temperature is above a

specified temperature.

International Comfort Products, LLC Page 6 48201530101 Sep 2008

Page 7

TSTAT0406 & TSTAT0407

HEAT PUMP LOCKOUT – Does not allow the heat pump to operate when the outdoor temperature is below a specified temperature.

SMART RECOVERY

OFF

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the SMART RECOVERY option and pressing SELECT will bring up the SMART RECOVERY screen. Highlighting ON or OFF and pressing the SELECT button will turn smart recovery on or off and return the display to the PROGRAM SETTINGS screen. When SMART RECOVERY is ON, the thermostat tries to adjust the set temperature in advance of a programmed event to get the temperature adjusted to the set point at the time of the event. For example, if the set temperature is set for 65 degrees at 3PM and the next programmed event sets the temperature to 70 degrees at 5PM, the thermostat will start the system before 5PM to achieve 70 degrees at 5PM. The thermostat assumes a change rate of 6 degrees per hour so it would start at about 4:10 PM and slowly raise the set temperature to 70 at 5PM.

EVENTS PER DAY

4 - RESIDENTIAL

2 – RESIDENTIAL

2 - BUSINESS

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the EVENTS PER DAY option and pressing SELECT will bring up the EVENTS PER DAY screen. Pressing the UP or DOWN buttons will set the events per day to 2 or 4 and business or residential. This selection determines how many programmed events are available each day.

The Residential events are WAKE, LEAVE, RETURN, SLEEP for 4 events or WAKE and SLEEP for 2 events. The Business events are named ACTIVE and IDLE.

COOLING LOCK OUT

COOLING LOCKOUT

NO COOLING BELOW

55°

CHANGE SETTING ∇∆ ⊲ PREVIOUS

(OUTDOOR SENSOR REQUIRED)

Highlighting the COOLING LOCKOUT option in the PROGRAM SETTINGS screen and pressing the SELECT button will bring up the COOLING LOCKOUT SCREEN. This setting can be set from NONE to 55 degrees. When there is an outdoor thermistor attached and the outdoor temperature is below the set Cooling Lockout point, the cooling will not operate. Pressing the UP and DOWN buttons will change the setting and pressing the SELECT button will apply the setting.

ELECTRIC HEAT /FURNACE LOCKOUT (OUTDOOR SENSOR REQUIRED)

ELECTRIC HEAT LOCKOUT

NO EHEAT ABOVE

55°

CHANGE SETTING ∇∆ ⊲ PREVIOUS

BALANCE POINT (OUTDOOR SENSOR REQUIRED) – USED IN DUAL FUEL MODE

BALANCE POINT

NO HEAT PUMP BELOW

35°

Highlighting the ELECTRIC HEAT LOCKOUT (FURNACE LOCKOUT if configured as GAS or DUAL FUEL) option and pressing the SELECT button will bring up the ELECTRIC HEAT/FURNACE LOCKOUT screen. In a heat pump system with an outdoor thermistor, this setting allows the thermostat to lockout the electric heat when the outdoor temperature is above the Lockout set temperature. If your system is configured as a furnace, it will lockout the furnace when the outdoor temperature is above the lockout set temperature. Pressing the UP and DOWN buttons can change the setting temperature from NONE to 60 degrees. Pressing the SELECT button will apply the setting and return the display to the PROGRAM SETTINGS screen.

Highlighting the BALANCE POINT option and pressing the SELECT button will bring up the BALANCE

POINT screen. In a heat pump system with an outdoor thermistor, this setting allows the thermostat to

lockout the heat pump when the outdoor temperature is below the Lock Out set temperature.

Pressing the UP and DOWN buttons can change the setting temperature from NONE to 55 degrees.

Pressing the SELECT button will apply the setting and return the display to the PROGRAM SETTINGS

screen.

CHANGE SETTING ∇∆ ⊲ PREVIOUS

International Comfort Products, LLC Page 7 48201530101 Sep 2008

Page 8

TSTAT0406 & TSTAT0407

SERVICE INFORMATION

FAULT STATUS

FAULT STATUS FAULT CODE DEFINITION CLEAR FAULT HISTORY

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the SERVICE INFORMATION option and pressing the SELECT button brings up the SERVICE INFORMATION screen. Pressing the UP or DOWN button will alternate between FAULT STATUS, FAULT CODE DEFINITION and CLEAR FAULT HISTORY. Selecting FAULT STATUS allows the FAULT STATUS screen to be selected. Selecting CLEAR FAULT HISTORY allows the CLEAR FAULT HISTORY screen to be selected. Pressing the SELECT button when the desired option is highlighted enables that option.

FAULT STATUS

ACTIVE FAULT:

1 FLASH-LONG RUN TIME

LAST 3 FAULTS:

3 FLASH-SHORT CYCLING 5 FLASH-OPEN HI V CKT 9 FLASH-LOW VOLTAGE

Highlighting the FAULT STATUS option and pressing the SELECT button brings up the FAULT STATUS

screen. The ACTIVE FAULT indicates the active fault (if any) that is currently being transmitted from the “L”

output from the Comfort Alert Module. The LAST 3 FAULTS indicates the last 3 faults that were stored in

memory and transmitted from the Comfort Alert module from the most recent to the latest.

? PREVIOUS

FAULT CODE DESCRIPTION

FAULT CODE DEFINITION

FLASH CODE 1

FLASH CODE 1 FLASH CODE 2 FLASH CODE 3 FLASH CODE 4 FLASH CODE 5 FLASH CODE 6 FLASH CODE 7 FLASH CODE 8 FLASH CODE 9

SELECT OPTION ∇∆

⊲ PREVIOUS

Highlighting the FAULT CODE DEFINITION option and pressing the SELECT button brings up the FAULT CODE DEFINITION screen. Pressing the UP or DOWN button will alternate between FLASH CODE 1 THRU 9. Pressing the SELECT button when the desired selection is highlighted activates that option. Selecting one of the FLASH CODE options and pushing ENTER button will display the definition for the selected FLASH CODE.

CLEAR FAULT HISTORY

YES

SELECT OPTION ∇∆

⊲ PREVIOUS

Highlighting the CLEAR FAULT HISTORY option and pressing the SELECT button brings up the CLEAR

FAULT HISTORY screen.

Pressing the UP or DOWN button will alternate between NO & YES. Selecting NO will not change any of

the current adjustable settings and will return to the previous menu. Selecting YES will erase the Fault

Code History from the thermostat’s memory. Pressing the SELECT button when the desired option is

highlighted activates that option.

SERVICE NEEDED SCREEN

SERVICE NEEDED

CALL:

XXXXXXXXXXXXXXX 260-555-5555

BRAND:

XXXXXXXXXXXXXXX

MODEL NUMBER:

123ABC456DEF

SERIAL NUMBER:

123ABC456D

FAULT:

5 FLASH – OPEN HI V CKT

⊲ PREVIOUS

International Comfort Products, LLC Page 8 48201530101 Sep 2008

Anytime there is an active fault on the Comfort Alert module and the “L” input is wired to the TSTAT0406, TSTAT0407 thermostats or NAXA00101DB Daughter Board, the thermostat display will display the SERVICE NEEDED screen with the corresponding Comfort Alert Fault. The CONTRACTOR NAME, CONTRACTOR PHONE NUMBER, MODEL NUMBER and SERIAL NUMBER of the outdoor unit will be displayed also if the information has been programmed into the thermostat at the INPUT DEALER INFO screen in the INSTALLER SETUP menu. To exit the SERVICE NEEDED screen while there is an active fault, push the ◄ PREVIOUS button. Pushing the ◄ PREVIOUS button resets the active fault counter within the thermostat. If the fault is still active and the fault is validated after the proper recognition timing, the fault will again be displayed in the SERVICE NEEDED screen.

Page 9

TSTAT0406 & TSTAT0407

DOWN STAGING

OFF

Highlighting the DOWN STAGING option and pressing the SELECT button brings up the DOWN STAGING screen. Pressing the UP or DOWN button will alternate between ON & OFF. Selecting ON will allow the thermostat to down stage to a lower heating or cooling stage as the ambient temperature gets closer to the temperature setpoint. Selecting OFF forces the thermostat to satisfy the call for heat or cool on the highest active stage without down staging. Pressing the SELECT button when the desired option is highlighted

activates that option.

SELECT OPTION ∇∆

⊲ PREVIOUS

TEST MODE

TEST MODE SCREEN

HEAT PUMP MULTI

OFF

1ST STAGE COOL 2ND STAGE COOL

1ST STAGE HEAT 2ND STAGE HEAT 3RD STAGE HEAT 4TH STAGE HEAT EMERGENCY HEAT

SELECT OPTION ∇∆ ⊲ PREVIOUS

TEST MODE SCREEN

1ST STAGE COOL

W1 OFF W2 OFF

Y1 ON Y2 OFF GON O/B ON

MIN OFF TIMER = 0 TESTING TIMER = 28 MIN

CANCEL

■

Highlighting the TEST MODE option and pressing the SELECT button brings up the TEST MODE screen. Pressing the UP or DOWN button will alternate between OFF and a list of all the heating and cooling stages available in the model configuration you have programmed into the thermostat. Pressing the SELECT button when the desired option is highlighted activates that option. Selecting the OFF option will not change any settings and will return to the previous screen. Selecting one of the heating or cooling stages options will go to the associated screen and show the list of thermostat inputs and display their OFF or ON status as well as the cooling or heating stage selected at the top of the screen. The minimum off timer is set to zero and the testing timer is set to 30 minutes. The screen will flash red then blue throughout the testing process until the testing timer is satisfied or the center CANCEL button is pushed.

COOL TO DEHUMIDIFY

YES

CHANGE MODE

⊲ PREVIOUS

Highlighting the COOL TO HUMIDIFY option and pressing the SELECT button brings up the COOL TO DEHUMIDIFY screen. Pressing the UP or DOWN button will alternate between YES & NO. Selecting YES will allow the HVAC equipment in cooling to dehumidify the conditioned space. This feature is used when the system does not have variable speed capabilities. This feature energizes the cooling outputs (Y1, G & O) and the H output whenever the need for dehumidification is needed. This feature is only active when there is no active call for heating or cooling. Selecting NO does not allow this feature to be active at any

time. Pressing the SELECT button when the desired option is highlighted activates that option.

COMFORT ALERT™ MODULE FAULT CODES

Status LED Status LED Description Status LED Troubleshooting Information

Green “POWER” Module has power Supply voltage is present at module terminals Red “TRIP” Thermostat demand signal

Yellow “ALERT” Flash Code 1

Yellow “ALERT” Flash Code 2

Y is present, but the compressor is not running.

Long Run Time Compressor is running extremely long run cycles

System Pressure Trip

Discharge or suction pressure out of limits or compressor overloaded

1. Compressor protector is open

• Check for high head pressure

• Check compressor supply voltage

2. Outdoor unit power disconnect is open

3. Compressor circuit breaker or fuse(s) is open.

4. Broken wire or connector is not making contact

5. Low Pressure switch open if present in system

6. Compressor contactor has failed open.

1. Low refrigerant charge

2. Evaporator blower is not running

• Check blower relay coil and contacts

• Check blower motor capacitor

• Check blower motor for failure or block age

• Check evaporator blower wiring and connec tors

• Check indoor blower control board

• Check thermostat wiring for open circuit

3. Evaporator coil is frozen

• Check for low suction pressure

• Check for excessively low thermostat s etting

• Check evaporator airflow (coil block ages or return air filter)

• Check ductwork or registers for block age

4. Faulty metering device

• Check TXV bulb installation (size, locatio n and contact)

• Check if TXV/fixed orifice is stuck closed or defective

5. Condenser coil is dirty

6. Liquid line restriction (filter drier block ed if present in system)

7. Thermostat is malfunctioning

• Check thermostat sub-base or wiring for short cir cuit

• Check thermostat installation (location, level)

8. Comfort Alert Module failure

1. High head pressure

• Check high pressure switch if present in s ystem

• Check if system is overcharged with ref rigerant

• Check for non-condensable in system

2. Condenser coil poor air circulation (dirty, block ed, damaged)

3. Condenser fan is not running

• Check fan capacitor

• Check fan wiring and connectors

• Check fan motor for failure or blockage

4. Return air duct has substantial leakage

5. If low pressure switch present in system, check Flash Code

6. 1 information

Status LED Status LED

Yellow “ALERT” Flash Code 3

Yellow “ALERT” Flash Code 4

Yellow “ALERT” Flash Code 5

Yellow “ALERT” Flash Code 6

Yellow “ALERT” Flash Code 7

Yellow “ALERT” Flash Code 8

Yellow “ALERT” Flash Code 9

Flash Code number corresponds to a number of LED flashes, followed by a pause and then repeated. TRIP and ALERT LED’s flashing at the same time means control circuit voltage is too low for operation.

Description Short Cycling

Compressor is running only briefly

Locked Rotor

Open Circuit

Open Start Circuit

Open Run Circuit

Current only in start circuit

Welded Contactor

Low Voltage

Control circuit < 17 VAC

Status LED Troubleshooting Information

1. Thermostat demand signal intermittent

2. Time delay relay or control board defective

3. If high pressure switch present, go to Flash Code 2 inf ormation

4. If low pressure switch present, go to Flash Code 1 inf ormation

1. Run Capacitor has failed

2. Lo w line voltage (contact utility if voltage disconnect is lo w)

3. Excessive liquid refrigerant in compressor

4. Compressor bearings are seized

• Measure compressor oil level

1. Outdoor unit power disconnected

2. Compressor circuit breaker or fuse(s) open

3. Compressor contactor has failed open.

• Check compressor contactor wiring and connectors

• Check for compressor contactor failure (bur ned, pitted or open)

• Check wiring and connection between suppl y and compressor

• Check for low pilot voltage at compr essor contactor coil

4. High pressure switch is open and requires m anual reset

5. Open circuit in compressor supply wiring or connection s

6. Unusually long compressor protector reset tim e due to extreme ambient temperature

7. Compressor windings are damaged

• Check compressor motor winding resistance

1. Run capacitor has failed

2. Open circuit in compressor start winding or connect ions

• Check wiring and connections= between suppl y and the compressor “S” terminal

3. Compressor start winding is damaged

• Check compressor motor winding resistance

1. Open circuit in compressor run wiring or connections

• Check wiring and connectors between suppl y and the compressor “R” terminal

2. Compressor run winding is damaged

• Check compressor motor winding resistance

1. Compressor contactor has failed closed

2. Thermostat demand signal not connected to module

1. Control circuit transformer is overloaded

2. Lo w line voltage (contact utility if voltage at disconnect is low)

• Check wiring connections

International Comfort Products, LLC Page 9 48201530101 Sep 2008

Page 10

TSTAT0406 & TSTAT0407

MAIN SCREEN

The Thermostat operation runs from the main screen. With the exception of the SERVICE NEEDED

8/08/05 8:45 AM

OUTDOOR FAN AUTO

93° HEATING

73° HEAT

SETPOINT HEAT 62 COOL 85

TEMP

RH MODE FAN MENU

TOP LINE

TIME and DATE – Normal operation CONFIGURATION ERROR – The thermostat was not correctly set up when installed. HOLD UNTIL (DATE and TIME) – Thermostat is in a temporary or Vacation Hold PERMANENT HOLD – Thermostat is in a permanent hold condition. CHANGE AIR FILTER – Maintenance time for air filter CHANGE UV LAMP – Maintenance time for UV Lamp SERVICE TIME – Maintenance time for system SERVICE HUMIDIFIER – Maintenance time for humidifier . NOTE: these service times are set in the INSTALLER SCREENS SMART RECOVERY – The system is starting early to achieve temperature at the programmed time. INTERMITTENT FAN – The fan is running its cycle set by the intermittent fan option. COMMUNICATION ERROR – Only used in systems with the NAXA00101DB daughter board. LOCKED – The thermostat is LOCKED. You will need to enter the unlock code. DEFROST ERROR –If unit is in defrost 15 minutes after initiation, the thermostat will flash the SERVICE NEEDED screen and display the EXCESS DEFROST TIME as the fault. The thermostat will only use Auxiliary heat outputs during this lockout.

BOTTOM LINE contains a group of selectable menus.

RH (RELATIVE HUMIDITY) – Model TSTAT0407 Only

NOTE: All errors and reminders shown in the top line are alternately flashed at 1 second intervals with the date and time.

RH (where used) displays the relative humidity and allows selection of humidity operation points. TEMP sets a temporary hold. This will change the set point until the next programmed temperature change point. This can change to CANCEL HOLD when a hold is active, RESET ALARM when an alarm or fault is active, and CANCEL ERROR when a DEFROST ERROR is present. MODE allows you to select which operating mode to use. HEAT, COOL, EHEAT, AUTO, or OFF. FAN allows selection of fan operation. AUTO, ON, or PROGRAMMED. MENU takes you to the MAIN MENU of options.

HUMIDITY

48%

HUMIDITY

HUMIDIFY SETTING 30

SELECT OPTION ∇∆

⊲ PREVIOUS

SCREEN, the display will revert to the Main Screen in 3 minutes if no buttons are pressed. The Main Screen displays the actual Temperature, the current MODE (HEAT, EHEAT, COOL, AUTO, OFF), and the temperature set points (Unless the MODE is set to OFF). If there is an Outdoor thermistor connected, the outdoor temperature is displayed. If the thermostat has Humidity sensing capability, the humidity may be displayed. HEATING will be displayed as a flashing icon under the FAN mode display on the main screen whenever there is an active heating thermostat call. COOLING will be displayed as a flashing icon under the FAN mode display on the main screen whenever there is an active cooling thermostat call. The top line of the MAIN SCREEN will normally display the time and date, but if exceptional conditions exist, the top line is used to display the condition. For example, if there is a HOLD

set, the indication HOLD UNTIL (TIME DATE) or PERMANENT HOLD will be flashed on the top line. If there are alerts from the alarm settings for filter or other maintenance, those are displayed on the top line. The bottom line is a menu group. These are selectable by using the Right and Left buttons to move the cursor and pressing the center SELECT button.

SET HUMIDITY

40%

CHANGE SETTING ∇∆ ⊲ PREVIOUS

Selecting RH and pressing the SELECT button will bring up the HUMIDITY screen on thermostats equipped with a humidity sensor. If the thermostat does not have a humidity sensor, this position will allow display of dealer information. The HUMIDIFY or DEHUMIDIFY settings can be changed by using the SELECT Button to choose the HUMIDIFY SETTING or DEHUMIDIFY SETTING box. NOTE: In order to be able to select a Humidify or Dehumidify setting, the HUMIDITY OPTION must be set for HUMIDIFY ONLY, DEHUMIDIFY ONLY or AUTO in the HUMIDITY SETTINGS screen in the INSTALLER SETTINGS menu. Use the UP and DOWN buttons to change the HUMIDIFY or DEHUMIDIFY setpoints within the preset ranges. When the desired setting is reached, press the SELECT button. The H output on the thermostat will activate in the humidification mode when the sensed ambient humidity is below the setpoint selected and there is an active call for heating. The H output on the thermostat will activate in the dehumidification mode when the sensed ambient humidity is above the setpoint selected and there is an active call for cooling. HUMIDIFY ONLY option displays only HUMIDIFY SETTING DEHUMIDIFY ONLY option displays only DEHUMIDIFY SETTING AUTO option displays both HUMIDIFY and DEHUMIDY SETTINGS

Note: Please note wiring diagrams for the humidifier and dehumidifier

options to ensure proper system operation.

International Comfort Products, LLC Page 10 48201530101 Sep 2008

Page 11

TSTAT0406 & TSTAT0407

TEMP

HOLD THIS

TEMPERATURE

UNTIL 10:30 P.M.

HEAT

COOL

62° 85°

CHANGE SET TEMP ∇∆ ⊲ PREVIOUS

MODE (OPERATING MODE)

OPERATING MODE MENU

OFF

AUTO

COOL HEAT EMERGENCY HEAT

CHANGE MODE ∇∆ ⊲ PREVIOUS

Selecting TEMP and pressing the SELECT button will bring up the HOLD THIS TEMPERATURE screen. If the mode is set for OFF, the temperature will be the last mode set. Shown is the AUTO mode.

NOTE: Pressing the UP or DOWN button from the MAIN screen when in any mode but OFF will bring up this screen.

Use the UP and DOWN buttons to change the set temperature for HEAT and COOL. When the desired temperature is reached, press the SELECT button. The COOL option will be highlighted if in HEAT and the mode is set to AUTO or the selection will be saved and the thermostat will enter a HOLD condition. The new settings will be used until the next programmed time is reached or the CANCEL HOLD is selected on the main screen. The next programmed time is shown on the screen. The next programmed time is also

displayed in a flashing message on the TOP LINE of the main screen.

Highlighting the MODE option and pressing the SELECT button will bring up the Operating Mode screen. Use the UP and DOWN button to highlight the desired operation mode and press the SELECT button to activate the desired operating mode. NOTE: the EMERGENCY HEAT mode is only available when the thermostat is configured for HEAT PUMP. The CONFIGURATION screen is in the INSTALLER SETTINGS screen. The AUTO setting allows the setting of a HEAT and COOL temperature and the thermostat will set the appropriate mode for maintaining the desired temperature.

FAN

FAN MENU

AUTO

PROGRAMMED FAN

SELECT OPTION ∇∆ ⊲ PREVIOUS

MENU (MAIN MENU)

MAIN MENU

SET DATE AND TIME

HOLD PROGRAM FAN MODE DISPLAY HUMIDITY DISPLAY DEALER INFO SETTINGS SECURITY LOCKOUT

⊲ PREVIOUS

SET DATE AND TIME

AUTO DAYLIGHT SAVING

SET DATE AND TIME

SELECT OPTION ∇∆ ⊲ PREVIOUS

International Comfort Products, LLC Page 11 48201530101 Sep 2008

Highlighting the FAN and pressing the SELECT button will bring up the FAN MODE screen. The options are:

AUTO – The thermostat will decide when the fan should be on based on the operation of the heat and cool outputs. ON – The fan is on continuously PROGRAMMED FAN – the fan will either be ON or AUTO based on the setting in the Program Screen.

Highlighting the MENU and pressing the SELECT button will bring up the MAIN MENU screen. Highlighting one of the options by using the UP and DOWN buttons will bring up the appropriate screen for that option. Pressing the LEFT button will take you back to the Main screen.

NOTE: Products without Humidity sensors will not show DISPLAY HUMIDITY.

yg g

AUTO DAYLIGHT SAVING

OFF

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the SET DATE AND TIME and pressing the SELECT button will bring up the SET DATE AND TIME SCREENS. The first screen gives an option of setting the AUTO DAYLIGHT SAVING time selection or the SET DATE AND TIME option.

Highlighting the AUTO DAYLIGHT SAVING selection and pressing the SELECT button will bring up the screen for selecting the AUTO DAYLIGHT SAVINGS TIME option.

Highlighting the OFF and pressing the SELECT button will turn OFF the

automatic adjustment for daylight savings time. Highlighting ON and pressing the SELECT button will turn on the automatic adjustment for daylight savings time.

Page 12

TSTAT0406 & TSTAT0407

SET DATE AND TIME

SET DAY

CHANGE SETTING ∇∆ ⊲ PREVIOUS

SET DATE AND TIME

SET MONTH

CHANGE SETTING ∇∆ ⊲ PREVIOUS

SET DATE AND TIME

SET YEAR

CHANGE SETTING ∇∆ ⊲ PREVIOUS

SET DATE AND TIME

SET HOUR

CHANGE SETTING ∇∆ ⊲ PREVIOUS

SET DATE AND TIME

SET MINUTES

CHANGE SETTING ∇∆ ⊲ PREVIOUS

Highlighting the SET DATE AND TIME and pressing the SELECT button will bring up the set date screens then progress through the set time screens. Using the UP and DOWN arrows will change the Month, Day, Year, Hour, and Minutes. Pressing the SELECT button when the desired setting is displayed will step on to the next setting. Pressing the LEFT button will go back to the last screen viewed.

Once the minutes are set and the SELECT button is pressed, the new time and date is accepted and the display returns to the MAIN

MENU.

HOLD MENU

VACATION

PERMANENT

Highlighting the HOLD and pressing the SELECT button will bring up the HOLD screens. The initial hold screen asks if the hold will be a permanent hold or a Vacation hold. A permanent hold will keep the hold setting until the hold is canceled by highlighting the CANCEL HOLD on the MAIN screen and pressing the SELECT button.

SELECT OPTION ∇∆

⊲ PREVIOUS

VACATION HOLD

SET HOLD TEMPERATURE

HEAT

COOL

62°

CHANGE SETTING ∇∆

⊲ PREVIOUS

A vacation hold will ask for a time and date to release the hold automatically. Use Hold the UP and DOWN buttons to change the temperature setting in HEAT or COOL as

85°

VACATION HOLD

HOLD UNTIL

5:00 P.M.

8/08/05

CHANGE SETTING ∇∆ ⊲ PREVIOUS

VACATION HOLD

HOLD UNTIL

8/08/05

5:00 PM

CHANGE SETTING ∇∆

⊲ PREVIOUS

appropriate and press the SELECT button to set the desired set temperature. Pressing the SELECT button will move the screen automatically to the next setting. Pressing the LEFT button will return to the last screen.

When the Temperature setting is complete, the next screen will be the TIME and DATE screen. Use the UP and DOWN buttons to select the desired date the press the SELECT button. The time set will be next. Use the UP and DOWN buttons to then select the desired time for the normal program to resume and press the SELECT button. The display will return to the MAIN MENU screen

PERMANENT HOLD

PROGRAM MENU

PERMANENT HOLD

SET HOLD TEMPERATURE

HEAT

62°

CHANGE SETTING ∇∆ ⊲ PREVIOUS

PROGRAM MENU

COPY

TUESDAY

THURSDAY

SATURDAY

EVERY DAY

WEEKENDS

SELECT OPTION ∇∆ ⊲ PREVIOUS

COOL

85°

MONDAY

WEDNESDAY

FRIDAY

SUNDAY

WEEKDAYS

Highlighting the PERMANENT HOLD and pressing the SELECT button will bring up the PERMENANT HOLD screen. Use the UP and DOWN buttons to set the desired temperature and press the SELECT button. The display will return to the MAIN MENU screen. A Permanent hold can be reset by changing the operating mode or by highlighting the CANCEL HOLD on the MAIN screen and pressing the SELECT button.

Highlighting the PROGRAM selection in the MAIN MENU and pressing the select button will bring up the PROGRAM MENU.

This menu allows the thermostat to change the set temperature depending on the day and time. The days of the week can be set independently, the weekdays can all be set together, the weekends can be set together or all the days can be set the same.

International Comfort Products, LLC Page 12 48201530101 Sep 2008

Page 13

TSTAT0406 & TSTAT0407

PROGRAMMING SCREEN

EVERY DAY

WAKE HEAT COOL FAN

LEAVE

RETURN

SLEEP

SAVE

⊲ PREVIOUS

70 78 AUTO

6:00A

8:00A 62 85 AUTO

5:00P 70 78 AUTO

10:00P 62 82 AUTO

To program a day, highlight the day to program and press SELECT. The display will go to the PROGRAMMING SCREEN. The programming screen will either have 4 events or 2 events to program depending on the EVENTS PER DAY setting in the SETTINGS menu. Use the UP and DOWN buttons to select an event to program and then use the RIGHT and LEFT buttons to navigate the time and temperature. To change the event time, highlight the time and use the UP and DOWN buttons to change the value. Go to the next value to change by pressing the SELECT or the RIGHT button. Go back to the last item by pressing the LEFT button. When the desired values are set, highlight the SAVE and press the SELECT button. If you wish to copy this program to another day or to all days, highlight the COPY and press SELECT button. You will be prompted to select the day to copy from and copy to. Press the SELECT button to copy or the LEFT button to go back.

DISPLAY HUMIDITY – TSTAT0407 Model Only

HUMIDITY

48%

HUMIDITY

HUMIDIFY SETTING 30

Highlighting the DISPLAY HUMIDITY option and highlighting YES and pressing the SELECT button will allow the humidity to be displayed on the MAIN SCREEN.

SELECT OPTION ∇∆

⊲ PREVIOUS

DISPLAY DEALER INFO

BRAND NAME:

XXXXXXXXXXXXXXXXXXXXX

FURNACE MODEL NUMBER:

XXXXXXXXXXXXXXXXXXXXX

HP MODEL NUMBER:

XXXXXXXXXXXXXXXXXXXXX

CONTRACTOR NAME:

XXXXXXXXXXXXXXXXXXXXX 260-555-5555

SERIAL NUMBER:

XXXXXXXXXXXXXXXXXXXXX

⊲ PREVIOUS SAVE

Highlighting the DISPLAY DEALER INFO option and pressing the SELECT button will bring up the YOUR DEALER IS screen. This is an information only screen and no options are available at this screen.

Note: Information needs to be manually input into the INPUT DEALER INPUT screen in the INSTALLER SETTINGS screen before the data can be displayed on this screen.

■

SETTINGS (SETTINGS MENU)

SETTINGS MENU

SCREEN SETTINGS

AUTO CHANGEOVER

INTERMITTENT FAN

SELECT OPTION ∇∆ ⊲ PREVIOUS

SCREEN SETTINGS

FAHRENHEIT OR CELSIUS

12 or 24 HOUR CLOCK

12 or 24 HOUR CLOCK LANGUAGE CONTRAST BACKLIGHT ON TIME

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the SETTINGS option on the MAIN MENU and pressing the SELECT button will bring up the SETTINGS MENU. The options available on the SETTINGS MENU are: SCREEN SETTINGS – these allow customizing the look of your screen. AUTO CHANGE OVER – Allows the use of the AUTO mode selection or disables this function. INTERMITTANT FAN – Runs the fan independently when the system has not run for a period of time to help equalize temperatures and mix the air.

Highlighting the SCREEN SETTINGS and pressing the SELECT button will bring up the SCREEN SETTINGS screen. The SCREEN SETTINGS options are: FAHRENHEIT OR CELSIUS – displays the temperature in F or C. 12 OR 24 HOUR CLOCK – displays the time in AM/PM or 24 hour style LANGUAGE – Only English is available at this time. CONTRAST – adjusts the darkness of the screen and characters BACKLIGHT ON TIME – sets the time the backlight stays on after the last button push.

International Comfort Products, LLC Page 13 48201530101 Sep 2008

Page 14

TSTAT0406 & TSTAT0407

FAHRENHEIT OR CELSIUS

TEMPERATURE SCALE

FAHRENHEIT

CELSIUS

Highlighting the FAHRENHEIT OR CELSIUS option and pressing the SELECT button will bring up the FAHRENHEIT OR CELSIUS screen. Use the UP and DOWN buttons to select the option desired and press the SELECT button. The display will convert to the selected temperature scale and return to the SETTINGS MENU.

SELECT OPTION ∇∆

⊲ PREVIOUS

12 OR 24 HOUR CLOCK

12 HOUR

24 HOUR

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the 12 OR 24 HOUR CLOCK option and pressing SELECT will bring up the 12 OR 24 HOUR CLOCK screen.

This option will display the time in 12 hour format (5:22 PM) or in 24 hour format (17:22)

Use the UP and DOWN buttons to select the desired display method and press the SELECT button to enable. The display will return to the SETTINGS menu.

LANGUAGE

At this time ENGLISH is the only option available.

CONTRAST

ADJUST FROM 1 TO 15 1 IS LOW – 15 IS HIGH

CHANGE SETTING ∇∆ ⊲ PREVIOUS

Highlighting the CONTRAST option and pressing the SELECT button will bring up the CONTRAST screen. The contrast can be changed in real time by pressing the UP and DOWN buttons. When the desired contrast is achieved, press the SELECT button and the display will return to the SETTINGS menu.

BACKLIGHT ON TIME

WITH NO BUTTON PUSH

SECONDS

CHANGE SETTING ∇∆ ⊲ PREVIOUS

Highlighting the BACKLIGHT ON TIME option and pressing the SELECT button will bring up the BACKLIGHT ON TIME screen. Use the UP and DOWN buttons to select the desired time for the backlight to stay on after the last button was pressed. It is usually not desirable to leave the backlight on continuously because the light may generate heat that could interfere with the room temperature measurement. When the desired on time is set, Press the SELECT button and return to the SETTINGS screen. (30 – 120 seconds)

To exit this or any other screen, press the LEFT button to return to the previous screen

International Comfort Products, LLC Page 14 48201530101 Sep 2008

Page 15

TSTAT0406 & TSTAT0407

AUTO CHANGEOVER

AUTO CHANGEOVER TIME

AUTO CHANGOVER TIME

AUTO OR MANUAL CHANGE

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the AUTO CHANGEOVER option and pressing the SELECT button will bring up the AUTO CHANGEOVER screen. Auto changeover allows the thermostat to determine if Heat or Cool should be active. The AUTO OR MANUAL option determines if the AUTO mode is available. The AUTO CHANGEOVER TIME option sets the minimum off time necessary before switching modes.

WARNING: The COOLING LOCKOUT feature in conjunction with an outdoor sensor should be used, or a low ambient kit to protect the compressor when operating in coo l ing in cold weather.

AUTO CHANGEOVER TIME

MINUTES

Highlighting the AUTO CHANGEOVER TIME and pressing the SELECT button brings up the AUTO CHANGEOVER TIME screen. This screen sets the minimum time the system must be idle before the automatic change of mode is allowed. For example, if the auto changeover time is set to 30 minutes and the system was cooling and the room temperature drops below the heat set point, the cooling must be idle for 30 minutes before the heating mode takes over. The settings can be from 5 to 120 minutes in 15 minute increments.

CHANGE SETTING ∇∆ ⊲ PREVIOUS

AUTO OR MANUAL CHANGE

AUTO

MANUAL

SELECT OPTION ∇∆ ⊲ PREVIOUS

Highlighting the AUTO OR MANUAL option and pressing the SELECT button brings up the AUTO OR MANUAL CHANGE screen. Pressing the UP or DOWN button will alternate between AUTO and MANUAL. Selecting AUTO allows the AUTO mode to be selected. Selecting MANUAL removes the AUTO mode from the MODE screen and requires manual selection of HEAT or COOL modes. Pressing the SELECT button when the desired option is highlighted enables that option.

INTERMITTENT FAN NO HEAT OR COOL CALL FAN ON TIME

INTERMITTENT FAN

NO HEAT OR COOL CALL

FAN ON TIME

MINUTES

CHANGE SETTING ∇∆

⊲ PREVIOUS

INTERMITTENT FAN NO HEAT OR COOL CALL FAN OFF TIME

INTERMITTENT FAN

NO HEAT OR COOL CALL

FAN OFF TIME

MINUTES

CHANGE SETTING ∇∆

⊲ PREVIOUS

Highlighting the INTERMITTENT FAN option and pressing the SELECT button will bring up the INTERMITTENT FAN screen. Setting the intermittent fan option will run the fan for up to 20 minutes on and up to 40 minutes off if there has been no heat or cool call for 60 minutes. The fan run time is set first. Using the UP and DOWN buttons can select a fan run time from OFF (No intermittent fan operation) to 20 minutes.

Pressing the SELECT button will bring up the next setting, the off time. This is the time the fan must be off before the intermittent fan ON time can begin. If there is no heat or cool call and the fan is not turned on manually or by the programmed setting, the fan will turn on and run for the minutes set in the FAN ON TIME screen. Pressing the UP and DOWN button can set an OFF TIME from 5 to 40 minutes. Pressing the SELECT button will enable the intermittent fan option and return the display to the PROGRAM SETTINGS screen.

International Comfort Products, LLC Page 15 48201530101 Sep 2008

Page 16

TSTAT0406 & TSTAT0407

SECURITY LOCK OUT

To lockout the thermostat totally, highlight TOTAL KEYPAD LOCKOUT and press the SELECT button. To allow temporary override of the programmed temperatures or a change of set temperature in

The ENTER PIN NUMBER screen will appear.

SECURITY LOCKOUT

TEMP ADJUST ONLY

TOTAL KEYPAD LOCKOUT

SELECT OPTION ∇∆

⊲ PREVIOUS

SECURITY LOCKOUT

ENTER PIN NUMBER

0 0 0 0

▲

CHANGE NUMBER ∇∆ ⊲ PREVIOUS

OPTION

Set Temperature

Displa y F or

Auto Daylight Savings Ti me

12 or 24 Hour Cl oc

Allow AUTO MODE

Temporary HOLD

Vacation Hol d

Permanent HOLD

Operating Mode

EVENTS PER DAY

TEMPERATURE OFFSET

REMOTE TEMPERATURE OFFSET

OUTDOOR TEMPERATURE OFFSET

HUMIDITY OFFSET

NO COOLIN G BELOW OUTDOOR TEMPER ATURE

NO ELECTRIC HEAT ABOVE OUTDOOR

ANTICI PATOR

TEMPERATURE

SMART RECOVERY

FAN OPERATI NG MODE

BACKLIGHT ON TI ME

CYCLES PER HOU

AUTO CHANGEOVER TIM

HUMIDITY SET POINT

DEHUMIDI FY SET POI NT

HUMIDITY OPTIONS

SMART HEAT STAGE TIME

SMART STAGING

INTERMITT ENT FAN ON TIME

INTERMITTENT FAN OFF TIM

LOCK SCREEN

AIR FILTER ALARM

AIR FI LTER ALARM MONTHS

AIR FILTER ALARM HOUR

HUMIDIFIER ALARM

HUMIDIFI ER ALARM MONTHS

HUMIDIFI ER ALARM HOURS

UV LAMP ALAR

UV LAMP ALARM MONTH

UV LAMP ALARM HOURS

SERVICE AIR CLEANER ALARM

SERVICE AIR CLEANER ALARM MONTHS

SERVICE AIR CLEANER ALARM HOURS

HEAT PUMP

BALANCE POINT

DEALER NAM

DEALER PHON

MODEL NUMBE

BRAND NAM

DOWN STAGI NG ON ON or OFF

COOL TO DEHUMI DIF

CONTRAST

Y YES YES o r NO

Highlighting the SECURITY LOCKOUT option from the MAIN MENU and pressing the SELECT button will bring up the SECURITY LOCKOUT screen. Activating the security lock out and setting a 4 digit PIN will prevent unauthorized changes to the thermostat. The lockout can be total, no functions are allowed without entering the PIN or partial that allows setting of a temporary hold to override the set temperature.

nonprogrammable systems, highlight the TEMP ADJUST ONLY and press the SELECT button.

Use the UP and DOWN buttons to change the highlighted PIN digit until the desired number is displayed. Press the SELECT button and the display will highlight the next digit. Be sure to choose a PIN that you will remember. When the last digit is selected, the screen will return to the MAIN SCREEN and attempts to change settings will flash the message LOCKED and bring up the UNLOCK SCREEN. Enter the PIN into the unlock screen to unlock and allow changes to the thermostat. Once the thermostat is unlocked, it is necessary to reset the PIN number to relock the thermostat.

NOTE: A PIN number of 9999 will always unlock the thermostat.

FACTORY DEFAULTS

DEFA U LT SE TTIN

30 SEC 15 TO ON

15 min. 5 TO 120

30 min OFF to 120 min.

MONTHS MONTHS OR HOURS

G RANGE

70 55 - 95

FF or C

ON ON or OFF

12 12 or 24

ON ON or OFF OFF ON or OFF OFF ON or OFF OFF ON or OFF OFF OFF, HEAT, COOL, EHEAT, AUTO

42 OR 4 0-5 TO +5 0-5 TO +5 0-5 TO +5 0-10 TO +10% 31 TO 9

NONE OFF- 45 - 55

NONE NONE - 5 - 60

OFF ON - OFF

AUTO AUTO - ON - PROGRAMMED

44 OR 6

40 10 - 50% 60 40 - 90%

NONE HUMIDIFY, DEHUMIDIFY, AUTO, NONE

ON ON - OFF OFF OFF TO 20

40 5 TO 40

OFF

6 OFF TO 48 months

1000 OFF to 3600

OFF OFF TO 48 MONTHS

0FF OFF TO 3600 hours

OFF OFF TO 48 months OFF OFF TO 3600

OFF OFF TO 48 months OFF OFF TO 3600 hours

OFF OFF - 5 TO 55

4 1 to 10 Blank Up to 20 charact ers Blank 10 numbers Blank Up to 20 charact ers Blank Up to 20 charact ers

OFF, ALL, AL LOW TEMPERATURE CHANGE

Default Set Back Program

ALL DAYS WAKE HEAT COOL FAN

6:00AM 70 78 AUTO

LEAVE

8:00 AM 62 85 AUTO

RETURN

5:00 PM 70 78 AUTO

SLEEP

10:00 PM 62 82 AUTO

International Comfort Products, LLC Page 16 48201530101 Sep 2008

Page 17

TSTAT0406 & TSTAT0407

OUTDOOR / INDOOR SENSOR INFORMATION

Refer to the Outdoor Sensor literature for details. The literature is included within the sensor packet with the thermostat.

NOTE: The outdoor can be used as an indoor sensor and connected to the ID and GND terminals on the back of the thermostat. When an indoor sensor is used, it overrides the thermostat’s onboard sensor.

TEMP

(Fº)

40 344711 11.21 306069 383353 3.74 3.00 31 247768 10.83 220935 274601 3.61 3.00 22 180147 10.44 161340 198955 3.48 3.00 13 132410 10.06 119063 145757 3.36 3.00

4 98324 6.50 91933 104716 3.25 2.00

5 73724 6.30 69079 78368 3.15 2.00 14 55787 6.10 52384 59190 3.05 2.00 23 42583 5.92 40062 45104 2.96 2.00 32 32773 2.85 31839 33707 2.85 1.00 41 25456 2.76 24753 26158 2.76 1.00 50 19932 2.68 19397 20466 2.68 1.00 59 15725 2.59 15318 16133 2.59 1.00 68 12497 2.51 12183 12811 2.51 1.00 77 10000 2.44 9756 10244 2.44 1.00 86 8055 2.37 8764 8246 2.37 1.00 95 6528 2.30 6378 6679 2.30 1.00

104 5323 4.48 5085 5562 2.24 2.00 113 4365 4.34 4176 4554 2.17 2.00 122 3599 4.22 3447 3751 2.11 2.00 131 2983 6.16 2800 3167 2.05 3.00 140 2486 5.99 2337 2635 2.00 3.00 149 2082 5.83 1961 2204 1.94 3.00 158 1753 5.67 1653 1852 1.89 3.00 167 1482 7.36 1373 1591 1.84 4.00 176 1258 7.17 1168 1349 1.79 4.00 185 1073 8.73 979.4 1167 1.75 5.00 194 918.9 8.51 840.7 997.1 1.70 5.00 203 789.9 9.96 711.3 868.6 1.66 6.00 212 681.6 9.68 615.6 747.6 1.61 6.00

Rnominal

(Ω)

RES. TOL

±%

Rmin. (Ω) Rmax. (Ω) TEMP. COEF.

(%/*F)

TEMP. ACCY.

(±*F)

International Comfort Products, LLC Page 17 48201530101 Sep 2008

Page 18

TSTAT0406 & TSTAT0407

NAXA00101DB DAUGHTER BOARD

The NAXA00101DB daughter board control allows for using 4 existing thermostat wires in an existing, finished home to communicate with the TSTAT0406 & TSTAT0407 thermostats. The daughter board translates the communicated heating and cooling needs and sends the normal discrete thermostat outputs to the indoor and outdoor equipment as needed. The NAXA00101DB Daughter Board must be used in conjunction with the TSTAT406 or TSTAT0407 Communicating Thermostat for proper operation. The daughter board provides a two-wire RS485 ModBus communication link and 24VAC to the communicating thermostat via a 4 wire connection scheme, “L” input from the Comfort Alert Module, a sensor input for the remote outdoor sensor, seven thermostat 24VAC outputs (W,G,Y,O,W2,Y2,H) and status & communication LED’s.

NAXA00101 Daughter Board Kit includes the following:

• NAXA00101DB Daughter Board

• 4 - # 6 Mounting Screws

• “L” Input Pigtail Wire Harness & wire nut

• Remote Outdoor Sensor Pigtail Wire Harness & wire nuts

• Installation Instructions

LOD

NAXA00101DB 1164-402 0735

Y2 W2 H - Y G W O

Daughter Board Terminals & Connections

See wiring diagrams for proper wiring and installation.

The following connections are provided in the P2 terminal block: (Power and Communication Connections to Communicating Thermostat)

P2 - Pin 1 "R" 24VAC hot power connection for communicating thermostat P2 - Pin 2 "GND" Ground connection for communicating thermostat P2 - Pin 3 “DX+” DX+ connection to the A+ Terminal on the communicating thermostat P2 – Pin 4 “DX-” DX- connection to the B- Terminal on the communicating thermostat

The following connections are provided in the P3 terminal block: (Outputs to the HVAC Equipment)

P3 – Pin 1 “O” 24 VAC thermostat output P3 – Pin 2 “W” 24 VAC thermostat output P3 – Pin 3 “G” 24 VAC thermostat output P3 – Pin 4 “Y” 24 VAC thermostat output P3 – Pin 5 “Not Used” 24 VAC thermostat output

The following connections are provided in the P4 terminal block: (Outputs to the HVAC Equipment)

P4 – Pin 1 “H” 24 VAC thermostat output P4 – Pin 2 “W2” 24 VAC thermostat output P4 – Pin 3 “Y2” 24 VAC thermostat output P4 – Pin 4 “R” 24 VAC system power input P4 – Pin 5 “C” 24 VAC system common input

The following connections are provided in the P5 Connector: (Optional Location for the Outdoor Sensor Hook-up)

P5 – Pin 1 “OD” Ground for Remote Outdoor Temperature Sensor P5 – Pin 2 “OD” Remote Outdoor Temperature Sensor input P5 – Pin 3 “Not used” P5 – Pin 4 “Not used”

The following connections are provided in the P8 Connector: (Optional Connection for the Comfort Alert ALARM Output)

P8 – Pin 1 “Not Used” ----- No Connect---P8 – Pin 2 “Not Used” - - - No connect - - P8 – Pin 3 “L” “L” fault input from Comfort Alert Module

International Comfort Products, LLC Page 18 48201530101 Sep 2008

Page 19

TSTAT0406 & TSTAT0407

Status LED Operation

The LED labeled LED5 is a status LED that will provide a “heart beat” blink of this LED to indicate that the NAXA00101DB communicating daughter board control is powered and working properly.

Communication LED Operation

The LED labeled LED3 will be illuminated for 100mS each time a successful communications packet is received from the TSTAT0406 or TSTAT0407 communicating thermostat.

Thermostat Call Output LED’s Operation There is an LED Output for each thermostat output from the daughter board. The corresponding LED will illuminate any time

the associated thermostat output is active.

“L” Input from Comfort Alert Module to Daughter Board

The Comfort Alert Module will transmit the active fault code. The Comfort Alert or thermostat does not have any effect on operation of the equipment during a Comfort Alert fault. The Comfort Alert fault output can be wired directly to the daughter board or communicating thermostat. When the Comfort Alert Module is wired to the “L” input of the daughter board, it will recognize the fault output after it has been active for 10 seconds. After the daughter board has recognized the active fault from the Comfort Alert Module, the daughter board will forward the fault information to the communicating thermostats via the communication wires. The communicating thermostat will then display the fault code as defined.

GENERIC AC TO FANCOIL WIRING (REFER TO UNITS I/O MANUAL FOR SPECIFICS)

REQUIRE

1 STAGE AC WITH 1 STAGE FANCOIL

THERMOSTAT FANCOIL AC THERMOSTAT FANCOIL AC THERMOSTAT FANCOIL AC

CCCCCCCC

W2 W2 W2 W2 W2

---

RR RR RR

W1 W W1W1 W1W1

HHHH

OPTIONAL

1 STAGE AC WITH VARIABLE SPEED

FANCOIL + 2 STAGE ELECTRIC HEAT

2 STAGE AC WITH VARIABLE SPEED

FANCOIL + 2 STAGE ELECTRIC HEAT

▬▬▬ R

O/B O/B O O/B O

Y2 Y2 Y1 Y2 Y/Y2 Y2 Y1 Y Y Y1 Y/Y2 Y Y1 Y1 Y1

GG GG GG

LLLLLL

---

A+ A+ A+

B- B- B-

GND GND GND

OD OD OD

ID ID ID

GND GND GND

OUTDOOR

SENSOR

OUTDOOR

SENSOR

OUTDOOR

GENERIC HP TO FANCOIL WIRING (REFER TO UNITS I/O MANUAL FOR SPECIFICS)

NOTES:

1 STAGE HP WITH 1 STAGE FANCOIL + 1

THERMOSTAT FANCOIL HP THERMOSTAT FANCOIL HP THERMOSTAT FANCOIL HP

REQUIRE

H ON THERMOSTAT - CAN BE PROGRAMMED FOR HUM OR DEHUM FUNCTION. DEHUM MUST BE SELECTED WHEN CONNECTED TO DEHUM ON VARIABLE SPEED FANCOIL.

STAGE ELECTRIC HEAT

CCCCCCCC

W2 W2 W2 W2 W2

---

RRRRRRRR

W1 WW2W1 W1W2W1 W1

HHHH

O/B O O/B O O O/B O O

Y2 Y2 Y1 Y2 Y/Y2 Y2 Y1 Y Y Y1 Y/Y2 Y Y1 Y1 Y

GG GG GG

LLLLLL

---

A+ A+ A+

B- B- B-

GND GND GND

OD OD OD

ID ID ID

GND GND GND

OUTDOOR

NOTE: “L” wire can be terminated at either the thermostat OR the daughter board.

SENSOR

OPTIONAL

1 STAGE HP WITH VARIABLE SPEED FANCOIL +2 STAGE ELECTRIC HEAT

OUTDOOR

SENSOR

2 STAGE HP WITH VARIABLE SPEED

FANCOIL + 2 STAGE ELECTRIC HEAT

OUTDOOR

International Comfort Products, LLC Page 19 48201530101 Sep 2008

SENSOR

▬▬▬ R

SENSOR

Page 20

TSTAT0406 & TSTAT0407

NOTES: 24 VAC HUM - GOES TO HUMIDIFIER, ENERGIZES ON A CALL FOR W

REQUIRED

1 STAGE AC WITH 1 STAGE FURNACE

GENERIC AC TO FURNACE WIRING (REFER TO UNITS I/O MANUAL FOR SPECIFICS

OPTIONAL

1 STAGE AC WITH VARIABLE SPEED FURNACE

2 STAGE AC WITH 2 STAGE VARIABLE SPEED

FURNACE

THERMOSTAT FURNACE AC THERMOSTAT FURNACE

CCCCCCCC

W2 W2 W2 W2 W2

---

RR RR RR

W1 W W1W1 W1W1

H H DEHUM H DEHUM

O/B O/B O O/B O

Y2 Y2 Y1 Y2 Y/Y2 Y2 Y1 Y Y Y1 Y/Y2 Y Y1 Y1 Y1

GG GG GG

LLLLLL

---

A+ A+ A+

B- B- B-

GND GND GND

OD OD OD

ID ID ID

GND GND GND

24VAC HUM 24 VAC HUM 24 VAC HUM

OUTDOOR

SENSOR

*8MPV* "C" SERIES OR NEW ER *8MPV* "C" SERIES OR NEW ER *9MPV* "D" SERIES OR NEW ER *9MPV* "D" SERIES OR NEW ER

OUTDOOR

SENSOR

AC THERMOSTAT FURNACE AC

▬▬▬ R

OUTDOOR

SENSOR

GENERIC HP TO FURNACE WIRING (REFER TO UNITS I/O MANUAL FOR SPECIFICS

REQUIRED

NOTES:

1 STAGE HP WITH 1 STAGE FURNACE 1 STAGE HP WITH VARIABLE SPEED FURNACE

THERMOSTAT FURNACE HP THERMOSTAT FURNACE HP THERMOSTAT FURNACE HP

CCCCCCCC

W2 W2 W2 W2 W2

---

RRRRRRRR

W1 WW2W1W1W2W1W1

H H DEHUM H DEHUM

O/B O O/B O O O/B O O

Y2 Y2 Y1 Y2 Y/Y2 Y2 Y1 Y Y Y1 Y/Y2 Y Y1 Y1 Y

GG GG GG

LLLLLL

---

A+ A+ A+

B- B- B-

GND GND GND

OD OD OD

ID ID ID

GND GND GND

24 VAC HUM - GOES TO HUMIDIFIER, ENERGIES ON A CALL FOR W H - CAN BE PROGRAMMED FOR HUM OR DEHUM FUNCTION. DEHUM MUST BE SELECTED W HEN CONNECTED TO DEHUM ON VARIABLE SPEED FURNACE.

24VAC HUM 24 VAC HUM 24 VAC HUM

OUTDOOR

SENSOR

OPTIONAL

2 STAGE HP WITH 2 STAGE VARIABLE SPEED

OUTDOOR

SENSOR

*8MPV* "C" SERIES OR NEW ER *8MPV* "C" SERIES OR NEW ER *9MPV* "D" SERIES OR NEW ER *9MPV* "D" SERIES OR NEW ER

FURNACE

▬▬▬ R

OUTDOOR

SENSOR

= VARIABLE SPEED (DEHUM) = REQUIRED

AC WITH FANCOIL / PSC FURNACE + HUMIDIFIER HP WITH FANCOIL + HUMIDIFIER

VARIABLE SPEED

FANCOIL/SPP

THERMOSTAT

ONLY

THERMOSTAT

VARIABLE SPEED

FANCOIL ONLY

AC WITH VARIABLE SPEED FURNACE + HUMIDIFIER HP WITH VARIABLE SPEED FURNACE + HUMIDIFIER

THERMOSTAT

FURNACE

THERMOSTAT

H HC CC

C C 24 VAC HUM O

W1 O H DEHUM H DEHUM

H H

N.O. RELAY

HUMIDIFIE

115v

N.C. RELAY

HUMIDIFIER

115v

SPDT RELAY

HUMIDIFIE

115v

SPDT RELAY

HUMIDIFIE

115v

NOTE: A separate 115v supply should be used. NOTE: A separate 115v supply should be used. NOTE: A separate 115v supply should be used. NOTE: A separate 115v supply should be used.

NOTE: When using a humidifier on a HP co nnect to hot wat er. NOTE: When using a humidifier on a HP co nn ect to hot water.

International Comfort Products, LLC Page 20 48201530101 Sep 2008

FURNACE

ICP TSTAT0406, TSTAT0407 Installation Instructions & User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual