ICP PGF330080K, PGF324040K, PGF324060K, PGF330060K, PGF336060K Owner's Manual

Packaged Gas/Electric Units

Owner's Guide to Operating and

Maintaining Your Gas/Electric Unit

ELECTRICAL SHOCK HAZARD.

Failure to follow this warning can result in

property damage, personal injury, and/or death.

Disconnect power at fuse box or service panel

before performing recommended maintenance.

FIRE OR EXPLOSION HAZARD

Failure to follow this warning can result in
property damage, personal injury, and/or death.

Information in this manual MUST be followed

exactly.

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do touch any electrical switch; do not use any

phone in the building.

• Immediately evacuate the building and call your

gas supplier from a phone outside the building.

Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the

fire department.

• Installation and service must be performed by a

qualified installer, service agency or the gas
supplier.

This manual should be left with the owner.

Printed in U.S.A.

Code: PGF3 12/1/05 462 02 1001 00

11, Set the temperature selector on room thermostat to

desired setting.

TO LIGHT UNIT
Your combination heating!cooling unit is equipped with an

automatic direct spark ignition and power combustion

blower,

FIRE AND/OR EXPLOSION HAZARD

Failure to follow this warning could result in
property damage, personal injury, and/or death.

Do not attempt to light by hand, personal injury
may result

FIRE AND/OR EXPLOSION HAZARD

Failure to follow this warning could result in
property damage, personal injury, and/or death.

1. If the main burners fail to light, or the blower
fails to start, shut down gas heating section and
call your dealer for service.

2. Never attempt to manually light the main

burners on unit with a match, lighter, or any other
flame. If the electric sparking device fails to light
the main burners, refer to the following shutdown

procedures, then call your dealer as soon as

possible.

TO SHUT UNIT OFF

FIRE AND/OR EXPLOSION HAZARD

Failure to follow this warning could result in
property damage, personal injury, and/or death.

Do not turn off the electrical power to unit without

first turning off the gas supply.

Before attempting to start the gas heating section,

familiarize yourself with all the procedures that

must be followed.

Refer to Figure 2 for gas valve location.

1, Set the temperature selector on room thermostat to the

lowest temperature setting and set system switch to
HEAT.

2, Close the external manual shutoff valve.

3. Turn off the electrical supply to the unit.

4. Remove the front access panel with a 5/16 -in. nut
driver.

5. Move the selector switch on the internal gas valve to the
OFF position and wait 5 minutes.

6. Move the selector switch on the internal gas valve to the
ON position.

7. Replace the front access panel.

8. Turn on the electrical supply to unit.

9. Open the external manual shutoff valve.

10. Set the temperature selector on room thermostat
slightly above room temperature to start unit. The

induced-draft combustion-air fan will start. Main gas

valve will open and burners should ignite the gas

within 25 seconds. If burners do not light within 25
seconds, the ignition control will go into a Retry Mode

that will take another 25 seconds. Ifthe burners fail to

ignite the gas in 4 consecutive attempts, the unit will
lockout for 3 hours.

FIRE AND/OR EXPLOSION HAZARD

Failure to follow this warning could result in
property damage, personal injury, and/or death.

Do not turn off the electrical power to unit without

first turning off the gas supply.

NOTE: tf unit is being shut down because the heating

season has ended, make sure to turn on power to cooling
system.

Ifunit is being shut down because of a malfunction, call your

dealer as soon as possible.

Should overheating occur or the gas supply fail to shut off,

shut offthe manual gas valve to the unit before shutting off
the electrical supply.

Do not use this unit if any part has been under water.
Immediately call a qualified service technician to inspect the
unit and to replace any part of the control system and any

gas control which has been under water.

Refer to Fig. 2 while proceeding with the following steps.

1. Set the temperature selector on room thermostat to
lowest temperature setting and set system switch to

OFR

2. Close the external manual shutoff valve.

3. Turn off the electrical power supply to the unit.

4. Remove the front access panel.

5. Move the selector switch on the internal gas valve to the
OFF position.

6. Replace the burner access panel.

7. Restore electrical power to the unit and set system
switch to COOL to ensure operation of the cooling
system during the cooling season.