ICOP VSX-6150E-V2, VSX-6150E-V2-PLUS User Manual

VSX-6150E-V2 / VSX-6150E-V2-PLUS

DM&P Vortex86SX 300MHz

PC/104 CPU Module

with 4S/2USB/LAN/GPIO

128MB DDR2 Onboard

User’s Manual

(Revision 1.1A)

Copyright

The information in this manua l is subject to cha nge without notice for continuous improvement in
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracies that may be contained in this document. And makes no commitment to update or to
keep current the information contained in this manual.

No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part ,
in any form or by any means without the prior written permission of the ICOP Technology Inc..

Copyright 2007 ICOP Technology Inc.
Manual No. IUM6150E-V2000-01 Ver.1.0A

October, 2009

Manual No. IUM6150E-V2000-01 Ver.1.1A

June, 2010

Trademarks Acknowledgment

Vortex86SX is the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties

and registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.

T a b l e o f C o n t e n t s

T a b l e o f C o n t e n t s.............................................................iii

C h a p t e r 1 Introduction……………………………………………1

1.1 Packing List............................................................1

1.2 Product Description................................................2

1.3 Specifications.........................................................3

1.4 Board Dimension....................................................4

C h a p t e r 2 Installation……………………………………………..5

2.1 Board Outline.........................................................5

2.2 Connectors & Jumpers Location............................6

2.3 Connectors & Jumpers Summary...........................8

2.4 Pin Assignments & Jumper Settings.......................9

2.5 System Mapping...................................................18

2.6 Watchdog Timer...................................................21

2.7 GPIO....................................................................22

2.8 SPI flash...............................................................23

C h a p t e r 3 Driver Installation……………………………………24
Appendix ………………………………………………………………..25

A. TCP/IP library for DOS real mode.............................25

B. BIOS Default Setting.................................................26

Warranty............................................................................................27

Vortex86SX-6150E-V2 Vortex86SX PC/104 CPU Module

1

C h a p t e r 1

Introduction

1.1 Packing List

Product Name Package

VSX-6150E-V2

&

VSX-6150E-V2-Plus

Embedded Vortex86SX CPU All-in-One Board
Manual & Drivers CD x 1

RS232 cable x 4
PRINT cable x1
IDE cable x 1
USB cable x 1 (USB port x 2)
LAN cable x 1
GPIO cable x 1
PS/2 Mouse cable x 1
PS/2 Keyboard cable x 1
Screw Kit x 1

Vortex86SX-6150E-V2 Vortex86SX PC/104 CPU Module

2

1.2 Product Description

The VSX-6150E-V2 family of low-power x86 embedded controller is designed to meet PC/104
specification, and integrated with the following features.

 300 MHz Vortex86SX System-On-Chip
 128 / 256MB DDR2 system memory
 Enhanced IDE
 10/100Mbps Ethernet
 2 USB 2.0 (host)
 Up to 4 serial ports
 Parallel port
 16-bit GPIOs

 Onboard

2MB SPI Flash

 PC/104-Plus expansion bus
 Meet PC/104 stacking spec.
 2 watchdog timer
 JTAG interface
 AMI BIOS
 Single voltage +5V DC
 Support extended operating

temperature range of -20°C to +70°C

The VSX-6150E-V2 PC/104 family of embedded controller is designed with backward
compatibility in mind, to provide migration path for projects facing end-of-life challenges with their
existing x86 based PC/104 controller. The VSX-6150E-V2 family of controller is designed as a
plug in replacement, with backward compatibility to support legacy software to help extend
existing product life cycle without heavy re-engineering.

VSX-6150E-V2 is suitable for broad range of data-acquisition, Industrial automation, Process
control, Automotive controller , AVL, Intelligent Vehicle management devic,Medical device,
Human machine interface, Robotics, machinery control And more…application that required
small footprint, low-power and low-cost hardware with open industry standard such as PC/104.

Vortex86SX-6150E-V2 Vortex86SX PC/104 CPU Module

3

1.3 Specifications

Features VSX-6150E-V2

CPU

DM&P SoC CPU Vortex86SX- 30 0MHz
Real Time Clock with Lithium Battery Backup

Cache

L1:16K I-Cache, 16K D-Cache

BIOS

AMI BIOS

Bus Interface

PC/104 Standard Compliant (Optional: PCI-104)

System Memory

128 / 256MB DDR2 Onboard

Watchdog Timer

Software programmable from 30.5 us to 512 seconds x2
sets(Watchdog 1 fully compatible with M6117D)

LAN

Integrated 10/100M Ethernet

I /O Interface

Enhanced IDE port x1
RS-232 port x3
RS-232/485 port x1 (RS485: Auto Direction )
Parallel port x1
USB port x2 (USB 2.0 version)
16-bit GPIO port x1
10/100Mbps Ethernet port x1

Connectors

2.00 mm  44-pin box header for IDE x1

2.00 mm  10-pin box header for USB x1

2.00 mm  26-pin box header for Print x1

2.00 mm  20-pin b ox header for 16-bit GPIO x1

2.00 mm  10-pin box header for RS-232 x4

2.00 mm  8-pin header for Ethernet x 1

2.54 mm  5-pin box header for Keyboard x1

2.54 mm  5-pin header for Mouse x1

2.54 mm  4-pin header for DC-in x1

2.54 mm  3-pin header for RS-485 x1

2.54 mm  2-pin header for Reset x1

2.54 mm  7-pin header for Redundancy x1(Opt)

2.54 mm  2-pin header for SYS-Fail-SW- x1(Opt)

1.25 mm  6-pin Wafer for JTAG x1

Flash Disk Support

Onboard 2MB SPI Flash Disk (Driver: A)
44-pin IDE Flash Disk( EmbedDisk 16MB or above)

Power Requirement

Single Voltage +5V @ 400mA

Dimension

90 X 96mm (3.54 x 3.77 inches)

Weight

77g

Operating
Temperature

-20oC ~ +70oC

-40°C ~ +85°C (Optional)

Vortex86SX-6150E-V2 Vortex86SX PC/104 CPU Module

4

1.4 Board Dimension

Vortex86SX-6150E-V2 Vortex86SX PC/104 CPU Module

5

C h a p t e r 2

Installation

2.1 Board Outline

(Note1: COM2 RS232/485 is selected by BIOS setting)
(Note2: PCI-104 connector is optional)
(Note3: VI/O Default setting of PCI-104 connector is +5V)
(Note4: VSX-6150E-V2-256 is optional)
(Note5: Redundancy Signal and System-Fail-SW are optional)

Vortex86SX-6150E-V2 Vortex86SX PC/104 CPU Module

6

2.2 Connectors & Jumpers Location

Connectors

(Note1: J7 /J8 /J23 are Optional)