ICOP VSX-6126 User Manual

VSX-6126

DM&P Vortex86SX 300MHz

3.5” CPU Module

with 4S/3USB/VGA/LCD/LV DS/AUDIO/3LAN/GPIO/CF

128MB DDR2 Onboard

User’s Manual

(Revision 1.0A )

Copyright

The information in this man ual is subject to change without notice for continuous improvement in
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracies that may be contained in this document. And makes no commitment to update or to
keep current the information contained in this manual.

No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part ,
in any form or by any means without the prior written permission of the ICOP Technology Inc..

Copyright 2007 ICOP Technology Inc.
Manual No. IUM6126000-01 Ver.1.0A

Trademarks Acknowledgment

Vortex86SX is the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties

and registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.

November, 2008

T a b l e o f C o n t e n t s

T a b l e o f C o n t e n t s.....................................iii

C h a p t e r 1 Introduction……………………………………………1

1.1 Packing List............................................................1

1.2 Product Description................................................2

1.3 Specifications.........................................................3

1.4 Board Dimension....................................................5

C h a p t e r 2 Installation……………………………………………..6

2.1 Board Outline.........................................................6

2.2 Connectors & Jumpers Location............................7

2.3 Connectors & Jumpers Summary...........................9

2.4 Pin Assignments & Jumper Settings......................11

2.5 System Mapping...................................................21

2.6 Watchdog Timer.....................................................24

2.7 GPIO......................................................................25

2.8 SPI Flash...............................................................26

C h a p t e r 3 Driver Installation……………………………………27
Appendix ………………………………………………………………..28

A. TFT Flat Panel Data Output ......................................28

B. TFT Flat Panel Support List.......................................29

C. LVDS Flat Panel Support List....................................30

D. Flat Panel Hardware Setting.....................................31

E. Flat Panel Wiring and Lighting..................................32

F. TCP/IP library for DOS real mode..............................33

G. BIOS Default Setting.................................................34

Warranty............................................................................................35

C h a p t e r 1

Introduction

1.1 Packing List

Product Name Package

VSX-6126

Embedded Vortex86SX CPU All-in-One Board
Manual & Drivers CD x 1

RS232 cable x 4
PRINTER cable x1
IDE cable x 1
USB cable x 1 (USB port x 2)
LAN cable x 2
GPIO cable x 1
AUDIO Line x2
YKB for Keyboard & PS/2 Mouse x 1

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

1

1.2 Product Description

The VSX-6126 family of low-power x86 embedded controller is designed to meet 3.5”
specification, and integrated with the following features.

 300 MHz Vortex86SX System-On-Chip
 VGA, TFT/LVDS LCD support up to

1280x1024 resolution

 128MB DDR2 system memory
 Enhanced IDE (UltraDMA-100/66/33)
 10/100Mbps Ethernet x3
 3 USB 2.0 (host)
 Up to 4 serial ports
 Parallel port
 16-bit GPIO x1
 PC/104 expansion bus

 Onboard 2MB SPI Flash
 Meet PC/104 stacking spec.
 2 watchdog timer
 3 PWM channels
 JTAG interface
 AMI BIOS
 Mini-PCI (TypeⅢ)
 Single voltage +5V DC
 Support extended operating

temperature range of -20°C to +70°C

The VSX-6126 3.5” family of embedded controller is designed with backward compatibility in
mind, to provide migration path for projects facing end-of-life challenges with their existing x86
based 3.5” controller. The VSX-6126 family of controller is designed as a plug in replacement,
with backward compatibility to support legacy software to help extend existing product life cycle
without heavy re-engineering.

VSX-6126 is suitable for broad range of data-acquisition, Industrial automation, Process control,
Automotive controller, AVL, Intelligent Vehicle management devic,Medical device, Human
machine interface, Robotics, machinery control And more…application that required small
footprint, low-power and low-cost hardware with open industry standard such as 3.5 ”.

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

2

1.3 Specifications

Features VSX-6126

CPU

Cache
BIOS
Bus Interface

System Memory

Watchdog Timer

VGA

LAN
AUDIO

I /O Interface

DM&P SoC CPU Vortex86SX- 300MHz
Real Time Clock with Lithium Battery Backup

L1:16K I-Cache, 16K D-Cache
AMI BIOS
PC/104 Standard Compliant

128MB DDR2 onboard

Software programmabl e from 30.5 us to 512 seconds x2

sets(Watchdog 1 fully compatible with M6117D)

XGI Volari Z9s Chipset

VGA and TFT Flat Panel Interface Support

LVDS Flat Panel Interface Support

Onboard 32MB VGA Memory

Support resolution up to 1280 x 1024,16MB color s
Integrated 10/100M Ethernet

CM119 USB Audio controller

Enhanced IDE port (UltraDM A-100/66/33) x1
RS-232 port x3
RS-232/485 port x1 (RS485: Aut o Direction)
Parallel port x1
USB port x3 (USB 2.0 version)
16-bit GPIO port x1
10/100Mbps Ethernet port x3

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

3

Connectors

Flash Disk Support

Power Requirement
Dimension
Weight
Operating

Temperature

2.00 mm  44-pin box header for IDE x1

2.00 mm  44-pin box header for LCD x 1

2.00 mm  26-pin box header for Printer x1

2.00 mm  20-pin box header for 16-bit GPIO x1

2.00 mm  16-pin box header for LVDS x 1

2.00 mm  10-pin box header for RS-232 x3

2.00 mm  10-pin box header for USB x1

2.00 mm  8-pin header for LAN x 2

2.54 mm  4-pin header for DC-in x1

2.54 mm  3-pin header for RS-485 x1

2.54 mm  2-pin header for Reset x1

1.25 mm  6-pin Wafer for JTAG x1

1.25 mm  4-pin Wafer for or Line-out/MIC-in x2

0.8mm  124-pin MiNi PCI connector x1
External 15-pin D-Sub female connector for VGA x1
External 9-pin D-Sub male connector for RS-232 x1

External RJ-45 con nector for Ethernet x1

External USB connector for x1
External Mini DIN so cket for Keyboard/M ouse x1
Type I/II Compact Flash slot x1

Onboard 2MB SPI Flash Disk (Driver: A)
44-pin IDE Flash Disk( EmbedDisk 16MB or above)
Type I/II CF Card

Single Voltage +5V @640mA
102 X 144mm (4.01 x 5.67 inches)
150g

-20oC ~ +70oC

-40°C ~ +85°C (Optional)

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

4

1.4 Board Dimension

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

5

C h a p t e r 2

Installation

2.1 Board Outline

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

6

2.2 Connectors & Jumpers Location

Connectors

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

7

Jumpers & LEDs

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

8

2.3 Connectors & Jumpers Summary

Summary Table

Nbr Description Type of Connections Pin nbrs.

J1 IDE Box Header, 2.0 ,22x2 44-pin
J3 USB 2 USB connector 4-pin
J4 USB 0 & USB 1 Box Header,2.0 , 5x2 10-pin
J6 LAN 1 RJ45 Connector 8-pin
J7 JTAG Wafer, 1.25 , 6x1 6-pin
J8 Reset Pin Header, 2,54,1x2 2-pin

J9 PS/2 Keyboard / Mouse Mini-DIN Female 6-pin
J10 COM1 D-Sub Male 9-pin
J11 GPIO Port 0 / 1 Box Header, 2.0 ,10x2 20-pin

J12

COM2(RS232/RS485)

J14 RS232 / RS485 Select

Box Header , 2.0 5x2 10-pin
Pin Header, 2.54, 3x1 3-pin

(COM 2)

J15 RS-485 Molex Header,2.54, 3x1 3-pin
J16 Power Connector Terminal Block 5.0,2x1 2-pin
J17 COM3 Box Header, 2.0 5x2 10-pin
J18 PRINT Box Header , 2.0 , 13x2 26-pin
J19 COM4 Box Header, 2.0 5x2 10-pin
J25 PC104 Connector – 64 pin Box Header, 2.54 32x2 64-pin
J26 PC104 Connector – 40 pin Box Header, 2.54 20x2 40-pin

J27

4P Power Source

Pin Header, 2.54 , 4x1 4-pin

(Interconnect to PC/104 –

J25)

J28 MINI_PCI _Type- Ⅲ Type- Ⅲ connector 124-pin
J30

VGA

D-Sub Female 15-pin

J31 LVDS Pin Header, 2.0 8x2 16-pin
J32

Display type Setup

Pin Header, 2.54 , 3x1

3-pin

J38
J33 LCD Box Header,2.0 ,22x2 44-pin
J39 LAN 2 Pin Header, 2.0 , 4x2 8-pin

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

9

J40 LAN 3
J41 CF Card Master/Slave Select

Pin Header, 2.0 , 4x2 8-pin
Slide SW 3-pin

J42 LINE-OUT Molex Header, 2.0, 4x1 4-pin
J43 MIC-IN Molex Header, 2.0, 4x1 4-pin

CF1 Compact Flash Type I/II CF Connector 50-pin

LAN Link/Active LED (Green)

LED-SMD

LAN Duplex LED ( Yellow ) LED-SMD
LAN Link/Active LED (Green)

LED-SMD

LAN Duplex LED ( Yellow ) LED-SMD
PWR_LED POWER Active LED (Red) LED-SMD
IDE_LED IDE Active LED (Green ) LED-SMD

MTBF-

MTBF-Out (Orange) LED-SMD

LED
SP1 BUZZER

S1 RESET SWITCH

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

10

2.4 Pin Assign ments & Jumper Settings

J1: IDE (44 Pins)

Pin # Signal Name Pin # Signal Name

1 IDERST 2 GND
3 IDED7 4 IDED8
5 IDED6 6 IDED9
7 IDED5 8 IDED10

9 IDED4 10 IDED11
11 IDED3 12 IDED12
13 IDED2 14 IDED13
15 IDED1 16 IDED14
17 IDED0 18 IDED15
19 GND 20 NC
21 IDEREQ 22 GND
23 IDEIOW 24 GND
25 IDEIOR 26 GND
27 ICHRDY 28 GND
29 IDEACK 30 GND
31 IDEINT 32 NC
33 IDESA1 34 IDECBLID
35 IDESA0 36 IDESA2
37 IDECS-0 38 IDECS1
39 IDELED 40 GND
41 VCC 42 VCC
43 GND 44 NC

J4: USB 0 & USB1

Pin # Signal Name Pin # Signal Name

1 VCC 2 VCC

3 LUSBD0- 4 LUSBD1-

5 LUSBD0+ 6 LUSBD1+

7 GND 8 GND

9 GGND 10 GGND

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

11

J7: JTAG

Pin # Signal Name Pin # Signal Name

1 VCC 2 GND

3 TCK 4 TDO

5 TDI 6 TMS

J8: RESET

Pin # Signal Name Pin # Signal Name

1 Reset 2 GND

J9: PS/2 Keyboard / Mouse

Pin # Signal Name Pin # Signal Name

1 KBDATA 2 NC

3 GND 4 VCC

5 KBCLK 6 NC

7 MSDATA 8 NC

9 GND 10 VCC
11 MSCLK 12 NC
13 GGND 14 GGND
15 GGND 16 GGND
17 GGND

J10: COM 1

Pin #

Signal

Pin #

Name

Signal

Name

1 DCD1 2 RXD1

3 TXD1 4 DTR1

5 GND 6 DSR1

7 RTS1 8 CTS1

9 RI1 10 GND
11 GND

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

12

J11: GPIO (Port 0 / 1)

Pin # Signal Name Pin # Signal Name

1 GND 2 VCC

3 GP00 4 GP10

5 GP01 6 GP11

7 GP02 8 GP12

9 GP03 10 GP13
11 GP04 12 GP14
13 GP05 14 GP15
15 GP06 16 GP16
17 GP07 18 GP17
19 VCC 20 GND

J12: COM2 (RS232 / RS485)

Pin # Signal Name Pin # Signal Name

1 DCD2 2 RXD2

3 TXD2 4 DTR2

5 GND 6 DSR2

7 RTS2 8 CTS2

9 RI2 10 TXDEN2

J14: RS232 COM2 Operation Mode Selector

Pin combinat ion Description

1-2 RS232
3-4 RS485

J15: RS485 (Auto direction)

Pin # Signal Name

1 RS485＋

2 RS485－

3 GND

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

13

J16: Power Connector (Terminal Block 5.0mm)

Pin # Signal Name

1 +5V

2 GND

J17: COM3

Pin # Signal Name Pin # Signal Name

1 DCD3 2 RXD3

3 TXD3 4 DTR3

5 GND 6 DSR3

7 RTS3 8 CTS3

9 RI3 10 NC

J18: PRINT

Pin # Signal Name Pin # Signal Name

1 STB- 2 PD0

3 PD1 4 PD2

5 PD3 6 PD4

7 PD5 8 PD6

9 PD7 10 ACK­11 BUSY 12 PE
13 SLCT 14 AFD­15 ERR- 16 INIT­17 SLIN- 18 GND
19 GND 20 GND
21 GND 22 GND
23 GND 24 GND
25 GND

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

14

J19: COM4

Pin # Signal Name Pin # Signal Name

1 DCD4 2 RXD4

3 TXD4 4 DTR4

5 GND 6 DSR4

7 RTS4 8 CTS4

9 RI4 10 NC

J25: PC104 Connector – 64pin

Pin # Signal Name Pin # Signal Name

1 IOCHCHK * 2 GND

3 SD7 4 RESETDRV

5 SD6 6 VCC

7 SD5 8 IRQ9

9 SD4 10 -5V
11 SD3 12 DRQ2
13 SD2 14 -12V
15 SD1 16 OWS
17 SD0 18 +12V
19 IOCHRDY 20 GND
21 AEN 22 SMEMW *
23 SA19 24 SMEMR *
25 SA18 26 IOW *
27 SA17 28 IOR *
29 SA16 30 DACK3 *
31 SA15 32 DRQ3
33 SA14 34 DACK1 *
35 SA13 36 DRQ1
37 SA12 38 REFRESH *
39 SA11 40 SYSCLK
41 SA10 42 IRQ7
43 SA9 44 IRQ6
45 SA8 46 IRQ5
47 SA7 48 IRQ4
49 SA6 50 IRQ3
51 SA5 52 DACK2 *
53 SA4 54 TC
55 SA3 56 BALE
57 SA2 58 VCC

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

15

59 SA1 60 OSC
61 SA0 62 GND
63 GND 64 GND

J26: PC104 Connector – 40pin

Pin # Signal Name Pin # Signal Name

1 GND 2 GND

3 MEMCS16 * 4 SBHE *

5 IOCS16 * 6 SA23

7 IRQ10 8 SA22

9 IRQ11 10 SA21
11 IRQ12 12 SA20
13 IRQ15 14 SA19
15 IRQ14 16 SA18
17 DACK0 * 18 SA17
19 DRQ0 20 MEMR *
21 DACK5 * 22 MEMW *
23 DRQ5 24 SD8
25 DACK6 * 26 SD9
27 DRQ6 28 SD10
29 DACK7 * 30 SD11
31 DRQ7 32 SD12
33 VCC 34 SD13
35 MASTER * 36 SD14
37 GND 38 SD15
39 GND 40 NC

J27: 4P Power Source (Interconnect to PC/104 – J25)

Pin # Signal Name

1 -5V

2 -12V

3 +12V

4 GND

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

16

J30: VGA

Pin # Signal Name Pin # Signal Name

1 R OUT 2 G OUT

3 B OUT 4 NC

5 GND 6 GND

7 GND 8 GND

9 VCC 10 GND
11 NC 12 DDCDAT
13 HSYNC 14 VSYNC
15 DDCCLK

J31: LVDS

Pin # Signal Name Pin # Signal Name

1 VCC3 (3.3V) 2 VCC3 (3.3V)

3 GND 4 GND

5 RxIN0+ 6 RxIN0-

7 RxIN1- 8 GND

9 GND 10 RxIN1+
11 RxIN2+ 12 RxIN2-
13 CKIN- 14 GND
15 GND 16 CKIN+

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

17

J32~J38: Display type setup (CRT /LCD)

Connector Pin # Signal Name

1 VCC

J32

J34

J35

J36

2 GPIOA
3 GND
1 VCC
2 GPIOB
3 GND
1 VCC
2 GPIOC
3 GND
1 VCC
2 GPIOD
3 GND
1 VCC

J37

J38

2 GPIOE
3 GND
1 VCC
2 GPIOF
3 GND

(Please refer to Appendix D, for Display t ype setup)

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

18

J33: LCD (DVO) Connector

Pin # Signal Name Pin # Signal Name

1 VCC3 2 VCC3

3 LG2 4 LG3

5 LG4 6 LG5

7 NC 8 NC

9 LR0 10 LR1
11 LR2 12 LR3
13 LR4 14 LR5
15 GND 16 NC
17 NC 18 NC
19 NC 20 GND
21 NC 22 NC
23 LB0 24 LB1
25 LB2 26 LB3
27 LB4 28 LB5
29 NC 30 NC
31 LG0 32 LG1
33 GND 34 GND
35 NC 36 LCLK
37 NC 38 LDE
39 NC 40 LHSYNC
41 NC 42 LVSYNC
43 LBACKL 44 LVDDEN

(Please refer to Appendix A, for TFT Flat Panel Data Output)

J39: LAN 2

Pin # Signal Name Pin # Signal Name

1 TX+1 2 TX-1

3 RX+1 4 LED01

5 LED01+ 6 RX-1

7 LED11+ 8 LED11

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

19

J40: LAN 3

Pin # Signal Name Pin # Signal Name

1 TX+2 2 TX-2

3 RX+2 4 LED02

5 LED02+ 6 RX-2

7 LED12+ 8 LED12

J42: LINE OUT

Pin # Signal Name

1 LOUTR

2 GND

3 GND

4 LOUTL

J43: MIC-IN

Pin # Signal Name

1 MICVREF

2 GND

3 GND

4 MIC-IN

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

20

2.5 System Mapping

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

21

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

22

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

23

2.6 Watchdog Timer

There are two watchdog timers in Vortex86SX CPU. One is compatible with M6117D watchdog
timer and the other is new. The M6117D compatible watchdog timer is called WDT0 and new
one is called WDT1.

We also provide DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech

http://www.dmp.com.tw/tech/vortex86sx/

or download the PDF file:

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

24

2.7 GPIO (General Purpose Input / Output)

40 GPIO pins are provided by the Vortex86SX for general usage in the system. All GPIO pins are
independent and can be configured as inputs or outputs, with or without pull-up/pull-down
resistors.

We also offer DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech

http://www.dmp.com.tw/tech/vortex86sx/

or download the PDF file:

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

25

2.8 SPI flash (Serial Peripheral Interface)

As SPI Flash (Serial Peripheral Interface) offers many benefits including: reduced controller pin
count, smaller and simpler PCBs, reduced switching noise, less power consumption, and lower
system cost

Many of users may consider using a formatted SPI flash to boot for the system or emulate SPI
flash as Floppy (A: Driver or B: Driver). Then you must know how to set for this condition in
CMOS Setup and boot up under DOS 6.22, X-DOS, DR-DOS and Free DOS.

For more technical support, please visit: http://www.dmp.com.tw/tech

http://www.dmp.com.tw/tech/vortex86sx/

or download the PDF file:

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

26

C h a p t e r 3

Driver Installation

VGA

The Vortex86SX processor also use external Display chip ““Volari™ Z9s” which is an ultra low
powered graphics chipset with total power consumption at around 1-1.5 W. It is capable in
providing VGA display output upto 1600x1200. With DVO interface, developers could easily
connect flat Panel to support TFT and LVDS output.

LAN

The Vortex86SX processor also integrated 10/100Mbps Ethernet controller that supports both
10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area
Network for full interaction with local servers, wide area networks such as the Internet.
I/O and IRQ settings can be done by software with the supplied utility software, or it can be set
for Plug and Play compatibility. The controller supports: Half / Full-Duplex Ethernet function to
double channel bandwidth, auto media detection.

AUDIO

CM119 is a highly integrated single chip USB audio controller specifically for VoIP (Voice over
internet protocol) application. All essential analog modules are embedded in CM119, including
dual DAC and earphone driver, ADC, microphone booster, PLL, regulator, and USB transceiver.
8 GPIO pins can constitute a 24 key matrix directly support keypad control function without MCU.

Many features are programmable with jumper pins or external EEPROM. Vender can customized
unique USB VID/PID to EEPROM for VoIP software authentication. Moreover, individual unique
phone number for each device is possible via serial number stored in external EEPROM.

The Vortex86SX-6126 3.5” CPU board provides the VGA and LAN drivers for DOS 6.22
Windows CE 5.0 and Windows Embedded CE 6.0. Please get the drivers from the Driver CD
which attached with the standard packing of Vortex86SX-6126 board or please get it from DMP
official website: http://www.dmp.com.tw/tech/vortex86sx/

Vortex86SX-6126 also supports most of the popular Linux distributions, for more detail
information, please visit DMP official website: http://www.dmp.com.tw/tech/vortex86sx/

.

.

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

27

Appendix

A. TFT Flat Panel Data Output

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

28

B.TFT Flat Panel Support List

Size Brand Resolution Model No.

5.7” Data image 320x240 FG050701DSSWBG01

5.7” Optrex 320x240 55264GD057J-FW-ABN

5.7” TOSHIBA 320x240 LTA057A343F

5.7” Sharp 320x240 (QVGA / VGA) LQ057Q3DC02

5.7” Kyocera 320x240 (QVGA / VGA) TCG057QV1AC-G10

5.7” PVI 320x240 (QVGA / VGA) PD057VU4 /U5

5.7” Data image 640x480 FG050710DSSWJG01/DG01

5.7” Ampire 640x480 AM-640480GTMQW-T00H

5.7” Sharp 640x480 LQ057V3DG01

5.7” CPT 640x480 CLAA057VA01

6.4” LG-PHILIPS 640x480 LB064V02

6.4” PVI 640x480 PD064VT2 /VT4 /VT5
7” Data image 800x480 FG0700A0DSSWBG01
7” LG-PHILIPS 800x480 LB070WV1
7” HITACHI 800x480 TX18D57VM2BAA
7” Samsung 800x480 LMS700KF05
7” NEC 800x480 NL3224BC35-20
7” PVI 800x480 PM070WL4
8” Sharp 640x480 LQ080V3DG01

8.4” Sharp 800x600 LQ084S3DG01

10.4” PVI 640x480 PD104VT1/VT2

10.4” NEC 640x480 NL6448AC33-18

10.4” Sharp 640x480 LQ104V1DG51/DG61

12.1” NEC 800x600 NL8060BC31-01

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

29

C. LVDS Flat Panel Support

Size Brand Resolution Model No.

3.5” PVI 640x480 PD035VL1

6.5” AUO 640x480 G065VN01

8.4” AUO 800x600 G084SN03

10.4” MITSUBISHI 800x600 AA104SG01

10.4” AUO 800x600 G104SN02

10.4” Sharp 800x600 LQ104S1LG61

12.1” MITSUBISHI 800x600 AA121SL03

12.1” AUO 800x600 G121SN01

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

30

D. Flat Panel Hardware Setting:

The Vortex86SX-6126 offers the Hardware setting for the various TFT LCD Flat Panels support
and please make sure the jumper setting (J32~J38) before you connect the LCD.

Display type setup

Connector

1-2 2-3

J32 C
J34 C
J35 O O

LCD

J36 O O
J37 C
J38 C

Note: "C" means close; "O" means open

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

31

E. Flat Panel Wiring and Lighting

 Hardware

Before you connect the TFT LCD Flat Panel with Vortex86SX-6126, please make sure
that the input Voltage of LCD is 3.3V or Not

 BIOS

Please contact or e-mail our regional sales to get the special BIOS for the any TFT LCD
Flat Panels.

 Wiring LCD Cable

Please refer to Page 19 (J33: LCD connector) and Page 28~32. Or for more LCD lighting
and integration service, please contact our regional sales or mail to [e-mail]
you have any questions.

,if

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

32

F. TCP/IP library for DOS real mode

DSock is a TCP/IP library for DOS real mode, which is used by RSIP. It provides simple C
functions for programmer to write Internet applications. ICOP also provide Internet examples
using DSock: BOOTP/DHCP, FTP server, SMTP client/server, HTTP server, TELNET server,
Talk client/server, etc.

DSock provides a lot of example source code. Programmer can add Internet functions to their
project easily and save development time. With a utility "MakeROM”, programmer also can make
a ROM image to fit their application, those examples can be seen in the following Application
systems: Mity-Mite Serial Server,

DSock is free for All ICOP products using M6117D/Vortex86/Vortex86SX CPU and ICOP also
provide the business version of DSock for those customers who are using other x86 CPUs.
If you would like to use DSock or business version of DSock, Please ma il to [e-mail]
contact your regional sales.

Please download the trial DSock software and Utilities from our website:

http://www.dmp.com.tw/tech/dmp-lib/dsock/

Web Camera Tiny Server and RSIP Serial Server.

or

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

33

G. BIOS Default setting

If the system cannot be booted after BIOS changes are made, Please follow below procedures in
order to restore the CMOS as default setting.

 Press “End” Key, when the power on

 Press <Del> to enter the AMI BIOS setup
 Press “F9” to Load Optimized Defaults
 Press “F10” to Save configuration changes and exit setup

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

34

Warranty

This product is warranted to be in good working order for a period of one year from the date of purchase.
Should this product fail to be in good working order at any time during this period, we will, at our option,
replace or repair it at no additional charge except as set forth in the following terms. This warranty does not
apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for
any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the
use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other
related party. Return authorization must be obtained from the vendor befo re returned merchandise will be
accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return
Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear
problem description.

Vortex86SX-6126 Vortex86SX 3.5” CPU Module

35