ICOP VDX-6329, VDX-6329-512 User Manual

VDX-6329/ VDX-6329-512

DM&P Vortex86DX 800MHz

3.5” CPU Module

with 6S/2USB/VGA/LCD/AUD IO/2LAN/CF/FDD

256MB DDR2 Onboard

User’s Manual

(Revision 1.1A)

Copyright

The information in this manua l is subject to cha nge without notice for continuous improvement in
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracies that may be contained in this document. And makes no commitment to update or to
keep current the information contained in this manual.

No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part ,
in any form or by any means without the prior written permission of the ICOP Technology Inc..

Copyright 2008 ICOP Technology Inc.
Manual No. IUM6329000-01 Ver.1.0A

April, 2010

Manual No. IUM6329000-01 Ver.1.1A

August, 2010

Trademarks Acknowledgment

Vortex86DX is the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties

and registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.

T a b l e o f C o n t e n t s

T a b l e o f C o n t e n t s.............................................................iii

C h a p t e r 1 Introduction……………………………………………1

1.1 Packing List............................................................1

1.2 Product Description................................................2

1.3 Specifications.........................................................3

1.4 Board Dimension....................................................5

C h a p t e r 2 Installation……………………………………………..6

2.1 Board Outline.........................................................6

2.2 Connectors & Jumpers Location............................7

2.3 Connectors & Jumpers Summary...........................9

2.4 Pin Assignments & Jumper Settings......................11

2.5 System Mapping...................................................24

2.6 Watchdog Timer...................................................27

2.7 GPIO....................................................................28

2.8 SPI flash...............................................................29

2.9 IDE to SD.............................................................30

C h a p t e r 3 Driver Installation……………………………………31
Appendix ………………………………………………………………..32

A. TFT Flat Panel Data Output ......................................32

B. TFT Flat Panel Support List.......................................33

C. LVDS Flat Panel Support List....................................35

D. Flat Panel Hardware Setting.....................................36

E. Flat Panel Wiring and Lighting..................................37

F. TCP/IP library for DOS real mode..............................38

G. BIOS Default Setting.................................................39

Warranty............................................................................................40

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

1

C h a p t e r 1

Introduction

1.1 Packing List

Product Name Package

VDX-6329

&

VDX-6329-512

Embedded Vortex86DX CPU All-in-One Board
Manual & Drivers CD x 1

RS232 cable x 6
PRINT cable x1
IDE cable x 1
VGA cable x 1
Audio cable x 2
FDD cable x 1
USB cable x 1 (US B port x 2)
LAN cable x 2
PS/2 Mouse cable x 1
PS/2 Keyboard cable x1

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

2

1.2 Product Description

The VDX-6329 family of low-power x86 embedded controller is designed to meet 3.5”
specification, and integrated with the following features.

 800MHz Vortex86DX Syst em-On-Chip
 VGA, TFT/LVDS LCD support up to

1280x1024 resolution

 256/ 512MB DDR2 system memory
 Enhanced IDE (UltraDMA-100/66/33)
 10/100Mbps Ethernet x2
 2 USB 2.0 (Host)
 Up to 6 serial ports
 Parallel port

 Onboard 4MB SPI Flash
 x-PCI expansion bus
 Meet PC/104 stacking spec.
 2 watchdog timer
 JTAG interface
 AMI BIOS
 Single voltage +5V DC
 Support extended operating

temperature range of -20°C to +70°C

The VDX-6329 3.5” family of embedded controller is designed with backward compatibility in
mind, to provide migration path for projects facing end-of-life challenges with their existing x86
based 3.5” controller. The VDX-6329 family of controller is designed as a plug in replacement,
with backward compatibility to support legacy software to help extend existing product life cycle
without heavy re-engineering.

VDX-6329 is suitable for broad range of data-acquisition, Industrial automation, Process
control, Automotive controller , AVL, Intelligent Vehicle management devic,Medical device,
Human machine interface, Robotics, machinery control And more…application that required
small footprint, low-power and low-cost hardware with open industry standard such as 3.5 ”.

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

3

1.3 Specifications

Features VDX-6329

CPU

DM&P SoC CPU Vortex86DX- 800MHz
Real Time Clock with Lithium Battery Backup

Cache

L1:16K I-Cache, 16K D-Cache, L2 Cache 128 KB

BIOS

AMI BIOS

Bus Interface

PC/104 Standard Compliant
32-bit x-PCI interfa ce, compatible with PCI Rev.2.1

System Memory

256/ 512MB DDR2 Onboard

Watchdog Timer

Software programmable fr om 30.5 us to 512 seconds x2
sets(Watchdog 1 fully compatible with M6117D)

VGA

XGI Volari Z9s Chipset
VGA and TFT Flat Panel Interface Support
LVDS Flat Panel Interface Support
Onboard 32MB VGA Memory
Support resolution up to 1280 x 1024,16MB color s

LAN

Realtek 8100B 10/100Mbps Ethernet Controller
Half/Full duplex capability

Audio

CM119 USB Audio controller

I /O Interface

Enhanced IDE port (UltraDMA -100/66/33) x1
FDD port x1
RS-232 port x5
RS-232/422/485 port x1 (RS-485: Auto Direction)
Parallel port x1
USB port x2 (USB 2.0 version)
10/100Mbps Ethernet port x2

Connectors

2.54mm  5-pin box header for Keyboard x1

2.54mm  5-pin header for Mouse x 1

2.54mm  3-pin header for RS-485 x1

2.54mm  2-pin header for Reset x1

2.54mm  4-pin header for DC-in x1

2.00mm  44-pin box header for IDE x1

2.00mm  44-pin box header for LCD x 1

2.00mm  34-pin box header for FDD x1

2.00mm  26-pin box header for Printer x1

2.00mm  10-pin box header for RS-232 x6

2.00mm  10-pin box header for USB x1

2.00mm  10-pin box header for VGA

2.00mm  8-pin header for LAN x 2

2.00mm  4-pin wafer for Line-out/MIC-in x 2

1.25mm  6-pin wafer for JTAG x1
Type I/II Compact Flash slot x1

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

4

Flash Disk Support

Onboard 4MB SPI Flash Disk (Dr iver: A)
44-pin IDE Flash Disk( EmbedDisk 16MB or above)
Type I/II CF Card
44-pin IDE to Micro SD (Optional)

SRAM support

512KB (Optional)

Power Requirement

Single Voltage +5V @ 800mA

Dimension

102 X 144mm (4.01 x 5.67 inches)

Weight

150g

Operating
Temperature

-20oC ~ +70oC

-40°C ~ +85°C (Optional)

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

5

1.4 Board Dimension

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

6

C h a p t e r 2

Installation

2.1 Board Outline

(Note1: COM2 RS232/422/485 is selected by BIOS setting)
(Note2: J39 Default setting of JTAG Has to be Disable: Pin 1 & Pin 2 short)
(Note3: VDX-6329-512 is optional)

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

7

2.2 Connectors & Jumpers Location

Connectors

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

8

Jumpers & LEDs

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

9

2.3 Connectors & Jumpers Summary

Summary Table

Nbr Description Type of Connections Pin nbrs.

J1 IDE Box Header, 2.0 ,22x2 44-pin
J2 CF Card Master/Slave Select Pin Header, 2.54, 2x1 2-pin
J4 USB Box Header,2.0 , 5x 2 10-pin
J7 JTAG Wafer, 1.25 , 6x1 6-pin
J8 Reset Pin Header, 2,54,1x2 2-pin
J9 PS2 Keyboard Box Header,2,54, 1x5 5-pin

J12

COM2(RS-232/422/485)

Box Header, 2.54 5x2 10-pin

J15 RS-485 Molex Header,2.54, 3x1 3-pin
J16 Power Connector Terminal Block 5.0,2x1 2-pin
J17 COM3 Box Header, 2.0 5x2 10-pin
J18 PRINT Box Header, 2.0 , 13x2 26-pin
J19 COM4 Box Header, 2.0 5x2 10-pin
J20 FDD Box H eader, 2.0 ,17x2 24-pin
J21 COM5 Box Header, 2.0 5x2 10-pin
J23 COM6 Box Header, 2.0 5x2 10-pin
J25 PC104 Connector – 64 pin Box Header, 2.54 32x2 64-pin
J26 PC104 Connector – 40 pin Box Header, 2.54 20x2 40-pin

J27

4P Power Source (Interconnect
to PC/104 – J25)

Pin Header, 2.54 , 4x1 4-pin

J30

VGA

Box Header, 2.0 5x2 10-pin

J32

J38

Display type Setup Pin Header, 2.54 , 3x1 3-pin

J33 LCD Box Header,2.0 ,22x2 44-pin
J39 JTAG Disable (Default setting)

Pin Header, 2,54,1x2 2-pin

J40 LINE-OUT Wafer , 2.0 , 4x1 4-pin
J41 MIC-IN Wafer , 2.0 , 4x1 4-pin
J42 LAN 1 Pin Header, 2.0 , 5x2 8-pin
J43 LAN 2 Pin Header, 2.0 , 5x2 8-pin
J44 LAN1 Enable/Disable Pin Header, 2.54, 2x1 2-pin
J45 LAN2 Enable/Disable Pin Header, 2.54, 2x1 2-pin
J46 Mouse Pin Header,2,54, 1x5 5-pin

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

10

J47 x-PCI

Box Header, 2.0 , 32x2 64-pin

J48 COM1 Box Header, 2.0 5x2 10-pin

CF1 Compact Flash Type I/II CF Connector 50-pin

PWR_L

ED

POWER Active LED (Red)

IDE_LED IDE Active LED (Green )

MTBF-

LED

MTBF-Out (Orange) LED-SMD

SP1 BUZZER

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

11

2.4 Pin Assignments & Jumper Settings

J1: IDE (44 Pins)

J2: CF Card Master / Slave Select

Pin # Signal Name

CLOSE Master

OPEN Slave

Pin # Signal Name Pin # Signal Name

1 IDERST 2 GND
3 IDED7 4 IDED8
5 IDED6 6 IDED9
7 IDED5 8 IDED10

9 IDED4 10 IDED11
11 IDED3 12 IDED12
13 IDED2 14 IDED13
15 IDED1 16 IDED14
17 IDED0 18 IDED15
19 GND 20 NC
21 IDEREQ 22 GND
23 IDEIOW 24 GND
25 IDEIOR 26 GND
27 ICHRDY 28 GND
29 IDEACK 30 GND
31 IDEINT 32 NC
33 IDESA1 34 IDECBLID
35 IDESA0 36 IDESA2
37 IDECS-0 38 IDECS1
39 IDELED 40 GND
41 VCC 42 VCC
43 GND 44 NC

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

12

J4: USB

Pin # Signal Name Pin # Signal Name

1 VCC 2 VCC

3 LUSBD0- 4 LUSBD1-

5 LUSBD0+ 6 LUSBD1+

7 GND 8 GND

9 GGND 10 GGND

J7: JTAG

Pin # Signal Name Pin # Signal Name

1 VCC 2 GND

3 TCK 4 TDO

5 TDI 6 TMS

J8: RESET

Pin # Signal Name Pin # Signal Name

1 Reset 2 GND

J9: PS/2 Keyboard

Pin # Signal Name Pin # Signal Name

1 KBCLK 2 KBDAT

3 NC 4 GND

5 VCC

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

13

J12: COM2 RS232 / RS422 / RS485 (Optional: TTL)

Pin # Signal Name Pin #

Signal Name

1 DCD2/ 422TX- / RS485- 2 RXD2 / 422TX+ / RS485+
3 TXD2 / 422RX+ 4 DTR2 / 422RX-

5 GND 6 DSR2
7 RTS2 8 CTS2
9 RI2 10 NC

J15: RS485 (Auto direction)

J16: Power Connector (Terminal Block 5.0mm)

Pin # Signal Name

1 +5V

2 GND

J17: COM3 (Optional: TTL)

Pin # Signal Name Pin # Signal Name

1 DCD3 2 RXD3

3 TXD3 4 DTR3

5 GND 6 DSR3

7 RTS3 8 CTS3

9 RI3 10 NC

Pin # Signal Name

1 RS485＋

2 RS485－

3 GND

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

14

J18: PRINT

Pin # Signal Name Pin # Signal Name

1 STB- 14 AFD-

2 PD0 15 ERR-

3 PD1 16 INIT-

4 PD2 17 SLIN-

5 PD3 18 GND

6 PD4 19 GND

7 PD5 20 GND

8 PD6 21 GND

9 PD7 22 GND
10 ACK- 23 GND
11 BUSY 24 GND
12 PE 25 GND
13 SLCT 26 NC

J19: COM4 (Optional: TTL)

Pin # Signal Name Pin # Signal Name

1 DCD4 2 RXD4

3 TXD4 4 DTR4

5 GND 6 DSR4

7 RTS4 8 CTS4

9 RI4 10 NC

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

15

J20: FDD

Pin # Signal Name Pin # Signal Name

1 GND 2 DENSEL
3 GND 4 NC
5 GND 6 NC
7 GND 8 INDEX\
9 GND 10 MTRO\

11 GND

12

DS1\

13 GND

14

DS0\

15 GND

16

MTR1\

17 GND

18

DIR\

19 GND

20

STEP\

21 GND

22

WD\

23 GND

24

WG\

25 GND

26

TR0\

27 GND

28

WP\

29 GND

30

RD\

31 GND

32

HDSEL\

33 GND

34

DSKCHG\

J21: COM5 (Optional: TTL)

Pin # Signal Name Pin # Signal Name

1 DCD5 2 RXD5

3 TXD5 4 DTR5

5 GND 6 DSR5

7 RTS5 8 CTS5

9 RI5 10 NC

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

16

J23: COM6 (Optional: TTL)

Pin # Signal Name Pin # Signal Name

1 DCD6 2 RXD6

3 TXD6 4 DTR6

5 GND 6 DSR6

7 RTS6 8 CTS6

9 RI6 10 NC

J25: PC104 Connector – 64pin

Pin # Signal Name

Pin

#

Signal Name

1 IOCHCHK * 2 GND
3 SD7 4 RESETDRV
5 SD6 6 VCC
7 SD5 8 IRQ9
9 SD4 10 -5V

11 SD3 12

DRQ2
13 SD2 14 -12V
15 SD1 16 OWS
17 SD0 18 +12V
19 IOCHRDY 20 GND
21 AEN 22 SMEMW *
23 SA19 24 SMEMR *
25 SA18 26 IOW *
27 SA17 28 IOR *
29 SA16 30 DACK3 *
31 SA15 32 DRQ3
33 SA14 34 DACK1 *
35 SA13 36 DRQ1
37 SA12 38 REFRESH *
39 SA11 40 SYSCLK
41 SA10 42 IRQ7
43 SA9 44 IRQ6
45 SA8 46 IRQ5
47 SA7 48 IRQ4
49 SA6 50 IRQ3
51 SA5 52 DACK2 *
53 SA4 54 TC
55 SA3 56 BALE

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

17

57 SA2 58 VCC
59 SA1 60 OSC
61 SA0 62 GND
63 GND 64 GND

J26: PC104 Connector – 40pin

J27: 4P Power Source (Interconnect to PC/ 104 – J25)

Pin # Signal Name

1 -5V
2 -12V
3 +12V
4 GND

Pin # Signal Name Pin # Signal Name

1 GND 2 GND
3 MEMCS16 * 4 SBHE *
5 IOCS16 *

6 SA23
7 IRQ10 8 SA22
9 IRQ11 10 SA21

11 IRQ12 12 SA20
13 IRQ15 14 SA19
15 IRQ14 16 SA18
17 DACK0 * 18 SA17
19 DRQ0 20 MEMR *
21 DACK5 * 22 MEMW *
23 DRQ5 24 SD8
25 DACK6 * 26 SD9
27 DRQ6 28 SD10
29 DACK7 * 30 SD11
31 DRQ7 32 SD12
33 VCC 34 SD13
35 MASTER * 36 SD14
37 GND 38 SD15
39 GND 40 NC

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

18

J30: VGA

Pin #

Signal

Name

Pin #

Signal

Name

1 R OUT 2 GND
3 G OUT 4 GND
5 B OUT 6 GND
7 HSYNC 8 GND
9 VSYNCD 10 GND

J32~J38: Display type setup (CRT /LCD)

Connector Pin # Signal Name

1 VCC
2 GPIOA

J32

3 GND
1 VCC
2 GPIOB

J34

3 GND
1 VCC
2 GPIOC

J35

3 GND
1 VCC
2 GPIOD

J36

3 GND
1 VCC
2 GPIOE

J37

3 GND

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

19

1 VCC
2 GPIOA

J38

3 GND

(Please refer to Appendix D, for Display type setu p)

J33: LCD (DVO) Connector

Pin # Signal Name Pin # Signal Name

1 +3.3V 2 +3.3V
3 LG2 4 LG3
5 LG4 6 LG5
7 NC 8 NC
9 LR0 10 LR1

11 LR2 12 LR3
13 LR4 14 LR5
15 GND 16 NC
17 NC 18 NC
19 NC 20 GND
21 NC 22 NC
23 LB0 24 LB1
25 LB2 26 LB3
27 LB4 28 LB5
29 NC 30 NC
31 LG0 32 LG1
33 GND 34 GND
35 NC 36 LCLK
37 NC 38 LDE
39 NC 40 LHSYNC
41 NC 42 LVSYNC
43 LBACKL 44 LVDDEN

(Please refer to Appendix A, for TFT Flat Panel Data Output)

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

20

J39: JTAG Disable (Default setting: Pin 1 & Pin 2 short)

Pin # Signal Name Pin # Signal Name

1 GND 2 JTAG Disable

J40: LINE OUT

Pin # Signal Name

1 LOUTR
2 GND
3 GND
4 LOUTL

J41: MIC-IN

Pin # Signal Name

1 MICVREF
2 GND
3 GND
4 MIC-IN

J42: LAN1

Pin # Signal Name Pin # Signal Name

1 TX+1 2 TX-1
3 RX+1 4 LED01
5 LED01+ 6 RX-1
7 LED11+ 8 LED11

J43: LAN2

Pin # Signal Name Pin # Signal Name

1 TX+2 2 TX-2
3 RX+2 4 LED02
5 LED02+ 6 RX-2
7 LED12+ 8 LED12

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

21

J44: LAN1 Enable/Disable

Pin # Signal Name

CLOSE LAN Off

OPEN LAN ON

J45: LAN2 Enable/Disable

Pin # Signal Name

CLOSE LAN Off

OPEN LAN ON

J46: PS/2 Mouse

Pin # Signal Name Pin # Signal Name

1 MSCLK 2 MSDATA
3 NC 4 GND
5 VCC

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

22

J47: x-PCI

Pin # Signal Name Pin # Signal Name

1 GND 2 GND

3 AD0 4 AD1

5 AD2 6 AD3

7 AD4 8 AD5

9 AD6 10 AD7

11 AD8 12 AD9
13 AD10 14 AD11
15 AD12 16 AD13
17 AD14 18 AD15
19 VCC 20 VCC
21 AD16 22 AD17
23 AD18 24 AD19
25 AD20 26 AD21
27 AD22 28 AD23
29 AD24 30 AD25
31 AD26 32 AD27
33 AD28 34 AD29
35 AD30 36 AD31
37 VCC3 38 VCC3
39 CBE-0 40 CBE-1
41 CBE-2 42 CBE-3
43 PGNT-0 44 PREQ-0
45 PGNT-1 46 PREQ-1
47 PGNT-2 48 PREQ-2
49 INT-A 50 INT-B
51 INT-C 52 INT-D
53 GND 54 GND
55 FRAME- 56 IRDY­57 TRDY- 58 STOP­59 SERR- 60 PAR
61 DEVSEL- 62 PLOCK­63 PCIRST- 64 PCICLK3

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

23

J48: COM1 (Optional: TTL/ GPIO-P4 / PWMx8)

Pin #

Signal

Name

Pin #

Signal

Name

1 DCD1 2 RXD1
3 TXD1 4 DTR1
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1 10 GND

11 GND

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

24

2.5 System Mapping

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

25

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

26

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

27

2.6 Watchdog Timer

There are two watchdog timers in Vortex86SX/DX CPU. One is compatible with M6117D
watchdog timer and the other is new. The M6117D compatible watchdog timer is called WDT0
and new one is called WDT1.

We also provide DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech

or download the PDF file:

http://www.dmp.com.tw/tech/vortex86dx/

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

28

2.7 GPIO (General Purpose Input / Output)

40 GPIO pins are provided by the Vortex86SX/DX for general usage in the system. All GPIO pins
are independent and can be configured as inputs or outputs, with or without pull-up/pull-down
resistors.

We also offer DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech

or download the PDF file:

http://www.dmp.com.tw/tech/vortex86dx/

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

29

2.8 SPI flash (Serial Peripheral Interface)

As SPI Flash (Serial Peripheral Interface) offers many benefits including: reduced controller pin
count, smaller and simpler PCBs, reduced switching noise, less power consumption, and lower
system cost

Many of users may consider using a formatted SPI flash to boot for the system or emulate SPI
flash as Floppy (A: Driver or B: Driver). Then you must know how to set for this condition in
CMOS Setup and boot up under DOS 6.22, X-DOS, DR-DOS and Free DOS.

For more technical support, please visit: http://www.dmp.com.tw/tech

or download the PDF file:

http://www.dmp.com.tw/tech/vortex86dx/

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

30

2.9 IDE to SD (Micro-SD)

Vortex86DX SoC also built-in simulation circuit to adapt SD to IDE in order to allow your system
to recognize Micro-SD card as C: or D: Driver

SD-1917: 44 pins IDE to SD Adapter is an ideal solution for industrial PC or embedded system
and 44 pins IDE to SD Adapter can be easily installed on all Vortex86DX-63xx CPU boards. You
or your customers just do the BIOS setting and use SD-1917 to connect IDE connector of
Vortex86DX-63xx directly.
For further inquiries of SD-1917, please contact ICOP sales team or mail to: [e-mail]
for your request.

<BIOS setting>

 Get into the BIOS setup Utility
 Choose Primary IDE Pin Select: SD card
 Press “F10” to Save configuration changes and exit setup

SD-1917: http://www.icop.com.tw/pddetail.aspx?id=125&pid=4

SD-1917

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

31

C h a p t e r 3

Driver Installation

VGA

The Vortex86DX processor also use external Display chip ““Volari™ Z9s” which is an ultra low
powered graphics chipset with total power consumption at around 1-1.5 W. It is capable in
providing VGA display output upto 1600x1200. With DVO interface, developers could easily
connect flat Panel to support TFT and LVDS output.

LAN

The Vortex86DX processor also integrated 10/100Mbps Ethernet controller that supports both
10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area
Network for full interaction with local servers, wide area networks such as the Internet.

The controller supports: Half / Full-Duplex Ethernet function to double channel bandwidth, auto
media detection.

AUDIO

CM119 is a highly integrated single chip USB audio controller specifically for VoIP (Voice over
internet protocol) application. All essential analog modules are embedded in CM119, including
dual DAC and earphone driver, ADC, microphone booster, PLL, regulator, and USB transceiver.
8 GPIO pins can constitute a 24 key matrix directly support keypad control function without MCU.

Operating system support

The Vortex86DX-6329 3.5” CPU board supports Embedded software: Free DOS, DOS 6.22,
PCDOS 7.1, DR-DOS,x-DOS,OS/2,Windows CE 6.0, Windows 98, Windows XP Professional,
Windows Embedded standard (XPE) and Windows 2000 (SP4).

Please get the drivers from the Driver CD which attached with the standard packing of
Vortex86DX-6329 board or please get it from DMP official website:

http://www.dmp.com.tw/tech/vortex86dx/

Vortex86DX-6329 also supports most of the popular Linux distributions, for more detail
information, please visit DMP official website: http://www.dmp.com.tw/tech/vortex86dx/
.

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

32

Appendix

A. TFT Flat Panel Data Output

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

33

B. TFT Flat Panel Support List

Size Brand Resolution Model No.

5.7” Data image 320x240 FG050701DSSWBG01

5.7” Optrex 320x240 55264GD057J-FW-ABN

5.7” TOSHIBA 320x240 LTA057A343F

5.7” Sharp 320x240 (QVGA / VGA) LQ057Q3DC02

5.7” Kyocera 320x240 (QVGA / VGA) TCG057QV1AC-G10

5.7” PVI 320x240 (QVGA / VGA) PD057VU4 /U5

5.7” Data image 640x480 FG050710DSSWJG01/DG01

5.7” Ampire 640x480 AM-640480GTMQW-T00H

5.7” URT 640x480 UMSH-8004MD-T

5.7” Sharp 640x480 LQ057V3DG01

5.7” CPT 640x480 CLAA057VA01

6.4” PVI 640x480 V16C6448AC

6.4” LG-PHILIPS 640x480 LB064V02

6.4” PVI 640x480 PD064VT2 /VT4 /VT5

6.4” Sharp 640x480 LQ064V3DG01
7” AUO 800x480 C070VW02V0
7” Data image 800x480 FG0700A0DSSWBG01
7” LG-PHILIPS 800x480 (TFT 24 bits) LB070WV1
7” HITACHI 800x480 TX18D57VM2BAA
7” Samsung 800x480 LMS700KF05
7” PVI 800x480 PM070WL4
7” URT 800x480 UMSH-8173MD-1T
7” CHI HSIN 800x480 LW700AT9309
8” Sharp 640x480 LQ080V3DG01

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

34

Size Brand Resolution Model No.

8” AUO 800x600 (TFT 24bits) A080SN01 V0

8.4” Sharp 800x600 LQ084S3DG01

10.4” PVI 640x480 PD104VT1/VT2

10.4” NEC 640x480 NL6448AC33-18

10.4” NEC 640x480 NL6448AC33-29

10.4” NEC 640x480 NL6448BC33-59

10.4” Sharp 640x480 LQ104V1DG51/DG61

10.4” Sharp 640x480 LQ10d368
11” Sharp 800x480 LQ110Y3DG01

12.1” NEC 800x600 NL8060BC31-01

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

35

C. Flat Panel Hardware Setting:

The Vortex86DX-6329 offers the Hardware setting for the various TFT LCD Flat Panels support
and please make sure the jumper setting (J32~J38) before you connect the LCD.

Display type setup

Connector

LCD

1-2 2-3

J32 C
J34 C
J35 X X
J36 X X
J37 C
J38 C

Note: "C" means close; "X" means open

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

36

D. LVDS Flat Panel Support List

If you would like to use LVDS Flat Panel with Vortex86SX / Vortex86DX series, please contact
our regional sales to get ICOP-0096 information or visit ICOP website:

http://www.icop.com.tw/pddetail.aspx?id=65&pid=4

ICOP–0096

: 18-bit TFT to LVDS converter and Cable-LVDS-30: LVDS Cable 30cm

Approved LVDS Flat Panel List

Size Brand Resolution Model No.

3.5” PVI 640x480 PD035VL1
5” PVI 640x480 PD050VL1

6.5” AUO 640x480 G065VN01

8.4” AUO 800x600 G084SN03

8.9” AUO 1024x600 A089SW01

8.9” CPT 1024x600 CLAA089NA0ACW

10.4” AUO 800x600 G104SN02

12.1” AUO 800x600 G121SN01
15” AUO 1024x768 G150XG01

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

37

E. Flat Panel Wiring and Lighting

 Hardware

Before you connect the TFT LCD Flat Panel with Vortex86DX-6329, please make sure
that the input Voltage of LCD is +3.3V or Not

 BIOS

Please contact or e-mail our regional sales to get the special BIOS for the any TFT LCD
Flat Panels.

 Wiring LCD Cable

Please refer to Page 19 (J33: LCD connector) and Page 32~37. Or for more LCD lighting
and integration service, please contact our regional sales or mail to [e-mail]

,if

you have any questions.

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

38

F. TCP/IP library for DO S real mode

DSock is a TCP/IP library for DOS real mode, which is used by RSIP. It provides simple C
functions for programmer to write Internet applications. ICOP also provide Internet examples
using DSock: BOOTP/DHCP, FTP server, SMTP client/server, HTTP server, TELNET server,
Talk client/server, etc.

DSock provides a lot of example source code. Programmer can add Internet functions to their
project easily and save development time. With a utility "MakeROM”, programmer also can make
a ROM image to fit their application, those examples can be seen in the following Application
systems: Mity-Mite Serial Server,

Web Camera Tiny Server and RSIP Serial Server.

DSock is free for All ICOP products using M6117D/Vortex86/Vortex86SX/Vortex86DX CPU and
ICOP also provide the business version of DSock for those customers who are using other x86
CPUs.
If you would like to use DSock or business version of DSock, Please mail to [e-mail]

or

contact your regional sales.
Please download the trial DSock software and Utilities from our website:

http://www.dmp.com.tw/tech/dmp-lib/dsock/

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

39

G. BIOS Default setting

If the system cannot be booted after BIOS changes are made, Please follow below procedures in
order to restore the CMOS as default setting.

 Press “End” Key, when the power on

 Press <Del> to enter the AMI BIOS setup
 Press “F9” to Load Optimized Defaults
 Press “F10” to Save configuration changes and exit setup

Vortex86DX-6329 Vortex86DX 3.5” CPU Module

40

Warranty

This product is warranted to be in good working order for a period of one year from the date of
purchase. Should this product fail to be in good working order at any time during this period, we
will, at our option, replace or repair it at no additional charge except as set forth in the following
terms. This warranty does not apply to products damaged by misuse, modifications, accident or
disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other
incidental or consequential damage resulting from the use, misuse of, originality to use this
product. Vendor will not be liable for any claim made by any other related party. Return
authorization must be obtained from the vendor before returned merchandise will be accepted.
Authorization can be obtained by calling or faxing the vendor and requesting a Return
Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a
clear problem description.