Page 1
VDX-6326RD / VDX-6326RD-512
DM&P Vortex86DX 800MHz
3.5” CPU Module
with 4S/3USB/VGA/LCD/LVDS/AUDIO/3LAN/GPIO/
CF/FDD/PWMx16
256MB DDR2 Onboard
User’s Manual
(Revision 1.2A)
Page 2
Copyright
The information in this manual is subject to change without notice for continuous improvement in
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracies that may be contained in this document and makes no commitment to update or to
keep current information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part,
in any form or by any means without the prior written permission of the ICOP Technology Inc.
Copyright 2008 ICOP Technology Inc.
Manual No. IUM6326000-01 Ver.1.0A August, 2009
Manual No. IUM6326000-01 Ver.1.1A April, 2010
Manual No. IUM6326000-01 Ver.1.2A December, 2014
Trademarks Acknowledgment
Vortex86DX is the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties
and registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.
Page 3
T a b l e o f C o n t e n t s
T a b l e o f C o n t e n t s ............................................................. iii
C h a p t e r 1 Introduction……………………………………………1
1.1 Packing List ............................................................ 1
1.2 Product Description ................................................ 1
1.3 Specifications ......................................................... 3
1.4 Board Dimension .................................................... 5
C h a p t e r 2 Installation……………………………………………..6
2.1 Board Outline ......................................................... 6
2.2 Connectors & Jumpers Location .................... ........7
2.3 Connectors & Jumpers Summary ........................... 9
2.4 Pin Assignments & Jumper Settings ......................11
2.5 System Mapping ................................................... 25
2.6 Watchdog Timer ................................................... 28
2.7 GPIO .................................................................... 29
2.8 SPI flash ............................................................... 30
2.9 PWM .................................................................... 31
3.0 IDE to SD ............................................................. 32
C h a p t e r 3 Driver Installation……………………………………33
Appendix ………………………………………………………………..34
A. TFT Flat Panel Data Output ...................................... 34
B. TFT Flat Panel Support List ....................................... 35
C. LVDS Flat Panel Support List .................................... 37
D. Flat Panel Hardware Setting ..................................... 38
E. Flat Panel Wiring and Lighting .................................. 39
F. TCP/IP library for DOS real mode .............................. 40
G. BIOS Default Setting ................................................. 41
Warranty ............................................................................................ 42
Page 4
This page is blank
Page 5
VDX-6326RD Vortex86DX 3.5” CPU Module
1
C h a p t e r 1
Introduction
1.1 Packing List
Product Name Package
VDX-6326RD
&
VDX-6326RD-512
Embedded Vortex86DX CPU All-in-One Board
Manual & Drivers CD x 1
RS232 cable x 3
PRINT cable x1
IDE cable x 1
FDD cable x 1
USB cable x 1
(U SB port x 2
)
LAN cable x 2
GPIO cable x 1
AUDIO Line x2
YKB for Keyboard & PS/2 Mouse x 1
Page 6
VDX-6326RD Vortex86DX 3.5” CPU Module
2
1.2 Product Description
The VDX-6326RD family of low-power x86 embedded controller is designed to meet 3.5”
specification, and integrated with the following features.
800MHz Vortex86DX System-On-Chip
VGA, TFT/LVDS LCD support up to
1280x1024 resolution
256/ 512MB DDR2 system memory
Enhanced IDE (UltraDMA-100/66/33)
3x 10/100Mbps Ethernet
3 USB 2.0 (Host)
Up to 4 serial ports
Parallel port
16-bit GPIO x1
Onboard 4MB SPI Flash
PC/104-Plus expansion bus (Opt.)
Meet PC/104 stacking spec.
2 watchdog timer
PWM 16~24 channels
JTAG interface
AMI BIOS
Mini-PCI (TypeⅢ)
Single voltage +5V DC
Support extended operating
temperature range of -20°C to +70°C
The VDX-6326RD 3.5” family of embedded controller is designed with backward compatibility
in mind, to provide migration path for projects facing end-of-life challenges with their existing
x86 based 3.5” controller. The VDX-6326RD family of controller is designed as a plug in
replacement, with backward compatibility to support legacy software to help extend existing
product life cycle without heavy re-engineering.
VDX-6326RD is suitable for broad range of data-acquisition, Industrial automation, Process
control, Automotive controller, AVL, Intelligent Vehicle management devic,Medical device,
Human machine interface, Robotics, machinery control And more…application that required
small footprint, low
-
power and low
-
cost hardware with open industry sta
ndard such as
3.5 ”.
Page 7
VDX-6326RD Vortex86DX 3.5” CPU Module
3
1.3 Specifications
Features VDX-6326RD
CPU
DM&P SoC CPU Vortex86DX- 800MHz
Real Time Clock with Lithium Battery Backup
Cache
L1:16K I-Cache, 16K D-Cache L2:128KB Cache
BIOS
AMI BIOS
Bus Interface
PC/104 Standard Compliant
PCI-104 (Optional)
System Memory
256/ 512MB DDR2 Onboard
Watchdog Timer
Software programmable from 30.5 us to 512 seconds x2
sets(Watchdog 1 fully compatible with M6117D)
VGA
XGI Volari Z9s Chipset
VGA and TFT Flat Panel Interface Support
LVDS Flat Panel Interface Support
Onboard 32MB VGA Memory
Support resolution up to 1280 x 1024,16MB colors
LAN
Integrated 10/100M Ethernet
Realtek 8100B 10/100Mbps Ethernet Controller
Half/Full duplex capability
Audio
CM119 USB Audio Controller
I /O Interface
Enhanced IDE port (UltraDMA-100/66/33) x1
FDD port x1
RS-232 port x3
RS-232/422/485 port x1 (RS-485:Auto Direction)
Parallel port x1
USB port x3 (USB 2.0 version)
16-bit GPIO port x1
10/100Mbps Ethernet port x3
Page 8
VDX-6326RD Vortex86DX 3.5” CPU Module
4
Connectors
2.00 mm ∅ 44-pin box header for IDE x1
2.00 mm ∅ 44-pin box header for LCD x 1
2.00 mm ∅ 34-pin box header for FDD x1
2.00 mm ∅ 26-pin box header for Printer x1
2.00 mm ∅ 20-pin box header for 16-bit GPIO x1
2.00 mm ∅ 16-pin header for LVDS x 1
2.00 mm ∅ 10-pin box header for RS-232 x3
2.00 mm ∅ 10-pin box header for USB x1
2.00 mm ∅ 8-pin header for Ethernet x 2
2.54 mm ∅ 4-pin header for DC-in x1
2.54 mm ∅ 3-pin header for RS-485 x1
2.54 mm ∅ 2-pin header for Reset x1
1.25 mm ∅ 6-pin wafer for JTAG x1
0.8mm ∅ 124-pin MiNi PCI connector x1
External 15-pin D-Sub female connector for VGA x1
External 9-pin D-Sub male connector for RS-232 x1
External RJ-45 connector for Ethernet x1
External USB connector for x1
External Mini DIN socket for Keyboard/Mouse x1
Type I/II Compact Flash slot x1
Flash Disk Support
Onboard 4MB SPI Flash Disk (Driver: A)
44-pin IDE Flash Disk( EmbedDisk 16MB or above)
Type I/II CF Card
44-pin IDE to Micro SD (Optional)
PWM
16~24 Channels
SRAM support
512KB (Optional)
Power Requirement
Single Voltage +5V @ 880mA
Dimension
102 X 144mm (4.01 x 5.67 inches)
Weight
150g
Operating
Temperature
-20oC ~ +70oC
-40°C ~ +85°C (Optional)
Page 9
VDX-6326RD Vortex86DX 3.5” CPU Module
5
1.4 Board Dimension
Page 10
VDX-6326RD Vortex86DX 3.5” CPU Module
6
C h a p t e r 2
Installation
2.1 Board Outline
(Note1: COM2 RS232/422/485 is selected by BIOS setting)
(Note2: J39 Default setting of JTAG Has to be Disable: Pin 1 & Pin 2 short)
(Note3: PCI-104 connector is optional)
(Note4: VI/O Default setting of PCI-104 connector is +5V)
(Note5: VDX-6326RD-512 is optional)
Page 11
VDX-6326RD Vortex86DX 3.5” CPU Module
7
2.2 Connectors & Jumpers Location
Connectors
Page 12
VDX-6326RD Vortex86DX 3.5” CPU Module
8
Jumpers & LEDs
Page 13
VDX-6326RD Vortex86DX 3.5” CPU Module
9
2.3 Connectors & Jumpers Summary
Summary Table
Nbr Description Type of Connections Pin nbrs.
J1 IDE Box Header, 2.0∅ ,22x2
44-pin
J2 CF Card Master/Slave Select Pin Header, 2.54∅, 2x1 2-pin
J3 USB 2 USB connector 4-pin
J4 USB 1 Box Header,2.0∅ , 5x2 10-pin
J6 10/100Base-T Ethernet LAN RJ45 Connector 8-pin
J7 JTAG Wafer, 1.25∅ , 6x1 6-pin
J8 Reset Pin Header, 2,54∅,1x2 2-pin
J9 PS/2 Keyboard / Mouse Mini-DIN Female 6-pin
J10 COM1 D-Sub Male 9-pin
J11 GPIO ( Port 0 / 1 /PWMx16) Box Header, 2.0∅ ,10x2
20-pin
J12
COM2(RS232/RS485/RS422) Box Header, 2.54∅ 5x2 10-pin
J15 RS-485 Molex Header,2.54∅, 3x1
3-pin
J16 Power Connector Terminal Block 5.0∅,2x1
2-pin
J17 COM3 Box Header, 2.0∅ 5x2 10-pin
J18 PRINT Box Header, 2.0∅ , 13x2
26-pin
J19 COM4 Box Header, 2.0∅ 5x2 10-pin
J20 FDD Pin Header, 2.0∅ ,17x2 24-pin
J25 PC104 Connector – 64 pin Box Header, 2.54∅ 32x2
64-pin
J26 PC104 Connector – 40 pin Box Header, 2.54∅ 20x2
40-pin
J27
4P Power Source (Interconnect
to PC/104 – J25)
Pin Header, 2.54∅ , 4x1
4-pin
J28 MINI_PCI _Type- Ⅲ Type- Ⅲ connector 124-pin
J29 PC/104 + (Optional) Box Header, 2.0∅ , 30x4
120-pin
J30
VGA D-Sub Female 15-pin
J31 LVDS Pin Header, 2.0∅ 8x2 16-pin
J32
J38
Display type Setup Pin Header, 2.54∅ , 3x1
3-pin
J33 LCD Box Header,2.0∅ ,22x2 44-pin
J39 JTAG Disable (Default setting)
Pin Header, 2,54∅,1x2 2-pin
J40 LINE-OUT Wafer, 1.25∅ , 4x1 4-pin
J41 MIC-IN Wafer, 1.25∅ , 4x1 4-pin
Page 14
VDX-6326RD Vortex86DX 3.5” CPU Module
10
J44 LAN2 Enable/Disable Pin Header, 2.54∅, 2x1 2-pin
J45 LAN3 Enable/Disable Pin Header, 2.54∅, 2x1 2-pin
CF1 Compact Flash Type I/II CF Connector 50-pin
PWR_L
ED
POWER Active LED (Red)
IDE_LED IDE Active LED (Green )
MTBF-
LED
MTBF-Out (Orange) LED-SMD
SP1 BUZZER
S1 RESET SWITCH
Page 15
VDX-6326RD Vortex86DX 3.5” CPU Module
11
2.4 Pin Assignments & Jumper Settings
J1: IDE (44 Pins)
J2: CF Card Master / Slave Select
Pin # Signal Name
CLOSE
Master
OPEN
Slave
Pin # Signal Name Pin # Signal Name
1 IDERST
2
GND
3 IDED7
4
IDED8
5 IDED6
6
IDED9
7 IDED5
8
IDED10
9 IDED4
10
IDED11
11 IDED3
12
IDED12
13 IDED2
14
IDED13
15 IDED1
16
IDED14
17 IDED0
18
IDED15
19 GND
20 NC
21 IDEREQ
22
GND
23 IDEIOW
24
GND
25 IDEIOR
26
GND
27 ICHRDY
28
GND
29 IDEACK
30
GND
31 IDEINT
32 NC
33 IDESA1
34
IDECBLID
35 IDESA0
36
IDESA2
37 IDECS
-0 38
IDECS1
39 IDELED
40
GND
41 VCC
42
VCC
43 GND
44 NC
Page 16
VDX-6326RD Vortex86DX 3.5” CPU Module
12
J4: USB 1
Pin # Signal Name Pin # Signal Name
1 VCC
2
VCC
3 LUSBD
0- 4
LUSBD
1-
5 LUSBD
0+ 6
LUSBD
1+
7 GND
8
GND
9 G
GND
10 GGND
J6: LAN1
Pin # Signal Name Pin # Signal Name
1 TD+ 2 TD3 RO+ 4 NC
5 NC 6 RO7 NC 8 NC
J7: JTAG
Pin # Signal Name Pin # Signal Name
1 VCC 2 GND
3 TCK 4 TDO
5 TDI 6 TMS
J8: RESET
Pin # Signal Name Pin # Signal Name
1 Reset 2 GND
J9: PS/2 KBD / Mouse
Pin # Signal Name Pin # Signal Name
1 KBCLK
2 MSCLK
3 GND
4
KBDAT
5 MSDAT
6
VCC
7 G
GND
8 GGND
9 G
GND
Page 17
VDX-6326RD Vortex86DX 3.5” CPU Module
13
J10: COM1 (Optional: TTL / GPIO-P4 / PWMx8)
Pin # Signal Name Pin # Signal Name
1 DCD1 2 RXD1
3 TXD1 4 DTR1
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1 10 GND
11 GND
J11: GPIO (Port 0 / Port 1 / PWMx16)
J12: COM2 RS232 / RS422 / RS485 (Optional: TTL)
Pin # Signal Name Pin # Signal Name
1 DCD2/422TX-/RS485-
2 RXD2/422TX+/RS485+
3 TXD2 / 422RX+ 4 DTR2 / 422RX-
5 GND 6 DSR2
7 RTS2 8 CTS2
9 RI2 10 NC
Pin # Signal Name Pin # Signal Name
1 GND 2 VCC
3 GP00 4 GP10
5 GP01 6 GP11
7 GP02 8 GP12
9 GP03 10 GP13
11 GP04 12 GP14
13 GP05 14 GP15
15 GP06 16 GP16
17 GP07 18 GP17
19 VCC 20 GND
Page 18
VDX-6326RD Vortex86DX 3.5” CPU Module
14
J15: RS485 (Auto direction)
J16: Power Connector (Terminal Block 5.0mm)
Pin # Signal Name
1 +5V
2 GND
J17: COM3 (Optional: TTL)
Pin # Signal Name Pin # Signal Name
1 DCD3 2 RXD3
3 TXD3 4 DTR3
5 GND 6 DSR3
7 RTS3 8 CTS3
9 RI3 10 NC
J18: PRINT
Pin # Signal Name Pin # Signal Name
1 STB- 14 AFD2 PD0 15 ERR3 PD1 16 INIT4 PD2 17 SLIN5 PD3 18 GND
6 PD4 19 GND
7 PD5 20 GND
8 PD6 21 GND
9 PD7 22 GND
10 ACK- 23 GND
11 BUSY 24 GND
12 PE 25 GND
13 SLCT 26 NC
Pin # Signal Name
1 RS485+
2 RS4853 GND
Page 19
VDX-6326RD Vortex86DX 3.5” CPU Module
15
J19: COM4 (Optional: TTL)
Pin # Signal Name Pin # Signal Name
1 DCD4 2 RXD4
3 TXD4 4 DTR4
5 GND 6 DSR4
7 RTS4 8 CTS4
9 RI4 10 NC
J20: FDD
Pin # Signal Name Pin # Signal Name
1 GND 2 D
ENSEL
3 GND 4 NC
5 GND 6 NC
7 GND 8
INDEX
\
9 GND 10
MTRO
\
11 GND 12 DS1
\
13 GND 14
DS0
\
15 GND 16
MTR1
\
17 GND 18
DIR\
19 GND 20
STEP
\
21 GND 22 WD\
23 GND 24 WG\
25 GND
26
TR0
\
27 GND
28 WP\
29 GND
30 RD\
31 GND
32
HDSEL
\
33 GND
34
DSKCHG
\
Page 20
VDX-6326RD Vortex86DX 3.5” CPU Module
16
J25: PC104 Connector – 64pin
Pin # Signal Name Pin # Signal Name
1 IOCHCHK
* 2 GND
3 SD7
4
RESETDRV
5 SD6
6
VCC
7 SD5 8
IRQ9
9 SD4
10 -5V
11 SD3
12
DRQ2
13 SD2
14 -12V
15 SD1
16
OWS
17 SD0
18
+12V
19 IOCHRDY
20
GND
21 AEN
22
SMEMW *
23 SA19
24
SMEMR *
25 SA18
26
IOW *
27 SA17
28
IOR *
29 SA16
30
DACK3 *
31 SA15
32
DRQ3
33 SA14
34
DACK1 *
35 SA13
36
DRQ1
37 SA12
38
REFRESH
*
39 SA11
40
SYSCLK
41 SA10
42
IRQ7
43 SA9
44
IRQ6
45 SA8
46
IRQ5
47 SA7
48
IRQ4
49 SA6
50
IRQ3
51 SA5
52
DACK2 *
53 SA4
54 TC
55 SA3
56 BALE
57 SA2
58
VCC
59 SA1
60
OSC
61 SA0
62
GND
63 GND
64
GND
Page 21
VDX-6326RD Vortex86DX 3.5” CPU Module
17
J26: PC104 Connector – 40pin
J27: 4P Power Source (Interconnect to PC/104 – J25)
Pin # Signal Name
1 -5V
2 -12V
3 +12V
4 GND
Pin # Signal Name Pin # Signal Name
1 GND
2
GND
3 MEMCS16
* 4 SBHE *
5 IOCS16 *
6 SA23
7 IRQ10
8 SA22
9 IRQ11
10 SA21
11 IRQ12
12 SA20
13 IRQ15
14 SA19
15 IRQ14
16 SA18
17 DACK0 *
18 SA17
19 DRQ0
20
MEMR *
21 DACK5 *
22
MEMW *
23 DRQ5
24
SD8
25 DACK6 *
26
SD9
27 DRQ6
28
SD10
29 DACK7 *
30
SD11
31 DRQ7
32
SD12
33 VCC
34
SD13
35 MASTER *
36
SD14
37 GND
38
SD15
39 GND
40 NC
Page 22
VDX-6326RD Vortex86DX 3.5” CPU Module
18
J29: PC/104 + (Optional)
VI/O Default setting: +5V
If you need to use VI/O as +3.3V, please see the page 19.
Pin # A B C D
1 GND
NC
+5V
AD00
2 VI/O(+5V
) AD02
AD01
+5V
3 AD05
GND
AD04
AD03
4 C/BE0#
AD07
GND
AD06
5 GND
AD09
AD08
GND
6 AD11
VI/O(+5V)
AD10
GND
7 AD14
AD13
GND
AD12
8 +3.3V
C/BE1#
AD15
+3.3V
9 SERR#
GND
NC
PAR
10 GND
PERR#
+3.3V
NC
11 STOP#
+3.3V
LOCK#
GND
12 +3.3V
TRDY#
GND
DEVSEL#
13 FRAME#
GND
IRDY#
+3.3V
14 GND
AD16
+3.3V
C/BE2#
15 AD18
+3.3V
AD17
GND
16 AD21
AD20
GND
AD19
17 +3
.3V AD23
AD22
+3.3V
18 IDSEL0
GND
IDSEL1
IDSEL2
19 AD24
C/BE3#
VI/O(+5V)
IDSEL3
20 GND
AD26
AD25
GND
21 AD29
+5V
AD28
AD27
22 +5V
AD30
GND
AD31
23 REQ0#
GND
REQ1#
VI/O(+5V)
24 GND
REQ2#
+5V
GNT0#
25 GNT1#
VI/O(+5V)
GNT2#
GND
26 +5V
CLK0
GND
CLK1
27 CLK2
+5V
CLK3
GND
28 GND
INTD#
+5V
RST#
29 +12V
INTA#
INTB#
INTC#
30 -
12V
NC NC
GND
Page 23
VDX-6326RD Vortex86DX 3.5” CPU Module
19
Please remove the 0 ohm (1206 type) of R260 and add 0 ohm (1206 type) on
R261
Page 24
VDX-6326RD Vortex86DX 3.5” CPU Module
20
J30: VGA
Pin # Signal Name Pin # Signal Name
1 R OUT 2 G OUT
3 B OUT 4 NC
5 GND 6 GND
7 GND 8 GND
9 VCC 10 GND
11 NC 12 DDCDAT
13 HSYNC 14 VSYNC
15 DDCCLK
J31: LVDS
Pin # Signal Name Pin # Signal Name
1 VCC3 (3.3V)
2 VCC3 (3.3V)
3 GND 4 GND
5 RxIN0+ 6 RxIN0-
7 RxIN1- 8 GND
9 GND 10 RxIN1+
11 RxIN2+ 12 RxIN2-
13 CKIN- 14 GND
15 GND 16 CKIN+
Page 25
VDX-6326RD Vortex86DX 3.5” CPU Module
21
J32~J38: Display type setup (CRT /LCD)
Connector
Pin # Signal Name
J32
1 VCC
2 GPIOA
3 GND
J34
1 VCC
2 GPIOB
3 GND
J35
1 VCC
2 GPIOC
3 GND
J36
1 VCC
2 GPIOD
3 GND
J37
1 VCC
2 GPIOE
3 GND
J38
1 VCC
2 GPIOF
3 GND
(Please refer to Appendix D, for Display type setup)
Page 26
VDX-6326RD Vortex86DX 3.5” CPU Module
22
J33: LCD (DVO) Connector
Pin # Signal Name Pin # Signal Name
1 +3.3V 2 +3.3V
3 LG2 4 LG3
5 LG4 6 LG5
7 NC 8 NC
9 LR0 10 LR1
11 LR2 12 LR3
13 LR4 14 LR5
15 GND 16 NC
17 NC 18 NC
19 NC 20 GND
21 NC 22 NC
23 LB0 24 LB1
25 LB2 26 LB3
27 LB4 28 LB5
29 NC 30 NC
31 LG0 32 LG1
33 GND 34 GND
35 NC 36 LCLK
37 NC 38 LDE
39 NC 40 LHSYNC
41 NC 42 LVSYNC
43 LBACKL 44 LVDDEN
(Please refer to Appendix A, for TFT Flat Panel Data Output)
J39: JTAG Disable (Default setting: Pin 1 & Pin 2 short)
Pin # Signal Name Pin # Signal Name
1 GND 2 JTAG Disable
Page 27
VDX-6326RD Vortex86DX 3.5” CPU Module
23
J40: LINE OUT
Pin # Signal Name
1 LOUTR
2 GND
3 GND
4 LOUTL
J41: MIC-IN
Pin # Signal Name
1 MICVREF
2 GND
3 GND
4 MIC-IN
J42: LAN2
Pin # Signal Name Pin # Signal Name
1 TX+
1 2 TX-1
3 RX+
1 4 LED0
1
5 LED0
1+ 6 RX-1
7 LED1
1+ 8
LED1
1
J43: LAN3
Pin # Signal Name Pin # Signal Name
1 TX+
2 2 TX-2
3 RX+
2 4 LED0
2
5 LED0
2+ 6 RX-2
7 LED1
2+ 8
LED1
2
J44: LAN2 Enable/Disable
Pin # Signal Name
CLOSE
LAN Off
OPEN
LAN ON
Page 28
VDX-6326RD Vortex86DX 3.5” CPU Module
24
J45: LAN3 Enable/Disable
Pin # Signal Name
CLOSE
LAN Off
OPEN
LAN ON
Page 29
VDX-6326RD Vortex86DX 3.5” CPU Module
25
2.5
System Mapping
Page 30
VDX-6326RD Vortex86DX 3.5” CPU Module
26
Page 31
VDX-6326RD Vortex86DX 3.5” CPU Module
27
Page 32
VDX-6326RD Vortex86DX 3.5” CPU Module
28
2.6 Watchdog Timer
There are two watchdog timers in Vortex86SX/DX CPU. One is compatible with M6117D
watchdog timer and the other is new. The M6117D compatible watchdog timer is called WDT0
and new one is called WDT1.
We also provide DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech or download the PDF file:
http://www.dmp.com.tw/tech/vortex86dx/
Page 33
VDX-6326RD Vortex86DX 3.5” CPU Module
29
2.7 GPIO (General Purpose Input / Output)
40 GPIO pins are provided by the Vortex86SX/DX for general usage in the system. All GPIO pins
are independent and can be configured as inputs or outputs, with or without pull-up/pull-down
resistors.
We also offer DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech or download the PDF file:
http://www.dmp.com.tw/tech/vortex86dx/
Page 34
VDX-6326RD Vortex86DX 3.5” CPU Module
30
2.8 SPI flash (Serial Peripheral Interface)
As SPI Flash (Serial Peripheral Interface) offers many benefits including: reduced controller pin
count, smaller and simpler PCBs, reduced switching noise, less power consumption, and lower
system cost
Many of users may consider using a formatted SPI flash to boot for the system or emulate SPI
flash as Floppy (A: Driver or B: Driver). Then you must know how to set for this condition in
CMOS Setup and boot up under DOS 6.22, X-DOS, DR-DOS and Free DOS.
For more technical support, please visit: http://www.dmp.com.tw/tech or download the PDF file:
http://www.dmp.com.tw/tech/vortex86dx/
Page 35
VDX-6326RD Vortex86DX 3.5” CPU Module
31
2.9 PWM (Pulse-width modulation)
Pulse-width modulation (PWM) of a signal or power source involves the modulation of its duty
cycle, to either convey information over a communications channel or control the amount of
power sent to a load.
The popular applications of pulse width modulation are in speed control of electric motors,
volume control of Class D audio amplifiers or brightness control of light sources and many other
power electronics applications.
The Vortex86DX SoC integrated 32 channels of PWM interface enabling the Automation, robotic
industry to a New Age x86 SoC platform and we also offer the sample code of PWM which will
guide the engineer to control the PWM functionality smoothly.
For more inquire of this sample code that please contact our sales team or mail to:
info@icop.com.tw
Page 36
VDX-6326RD Vortex86DX 3.5” CPU Module
32
3.0 IDE to SD (Micro-SD)
Vortex86DX SoC also built-in simulation circuit to adapt SD to IDE in order to allow your system
to recognize Micro-SD card as C: or D: Driver
SD-1917: 44 pins IDE to SD Adapter is an ideal solution for industrial PC or embedded system
and 44 pins IDE to SD Adapter can be easily installed on all Vortex86DX-63xx CPU boards. You
or your customers just do the BIOS setting and use SD-1917 to connect IDE connector of
Vortex86DX-63xx directly.
For further inquiries of SD-1917, please contact ICOP sales team or mail to: info@icop.com.tw
for your request.
<BIOS setting>
Get into the BIOS setup Utility
Choose Primary IDE Pin Select: SD card
Press “F10” to Save configuration changes and exit setup
SD-1917:
http://www.icop.com.tw/pddetail.aspx?id=125&pid=4
SD-1917
Page 37
VDX-6326RD Vortex86DX 3.5” CPU Module
33
C h a p t e r 3
Driver Installation
VGA
The Vortex86DX processor also use external Display chip ““Volari™ Z9s” which is an ultra low
powered graphics chipset with total power consumption at around 1-1.5 W. It is capable in
providing VGA display output upto 1600x1200. With DVO interface, developers could easily
connect flat Panel to support TFT and LVDS output.
LAN
The Vortex86DX processor also integrated 10/100Mbps Ethernet controller that supports both
10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area
Network for full interaction with local servers, wide area networks such as the Internet.
The controller supports: Half / Full-Duplex Ethernet function to double channel bandwidth, auto
media detection.
AUDIO
CM119 is a highly integrated single chip USB audio controller specifically for VoIP (Voice over
internet protocol) application. All essential analog modules are embedded in CM119, including
dual DAC and earphone driver, ADC, microphone booster, PLL, regulator, and USB transceiver.
8 GPIO pins can constitute a 24 key matrix directly support keypad control function without MCU.
Many features are programmable with jumper pins or external EEPROM. Vender can customize
unique USB VID/PID to EEPROM for VoIP software authentication. Moreover, individual unique
phone number for each device is possible via serial number stored in external EEPROM.
Operating system support
The Vortex86DX-6326RD 3.5” CPU board supports Embedded software: Free DOS, DOS 6.22,
PCDOS 7.1, DR-DOS,x-DOS,OS/2,Windows CE 6.0, Windows 98, Windows XP Professional,
Windows Embedded standard (XPE) and Windows 2000 (SP4)
Please get the drivers from the Driver CD which attached with the standard packing of
Vortex86DX-6326RD board or please get it from DMP official website:
http://www.dmp.com.tw/tech/vortex86dx/
Vortex86DX-6326RD also supports most of the popular Linux distributions, for more detail
information, please visit DMP official website: http://www.dmp.com.tw/tech/vortex86dx/
.
Page 38
VDX-6326RD Vortex86DX 3.5” CPU Module
34
Appendix
A. TFT Flat Panel Data Output
Page 39
VDX-6326RD Vortex86DX 3.5” CPU Module
35
B.TFT Flat Panel Support List
Size Brand Resolution Model No.
5.7” Data image 320x240 FG050701DSSWBG01
5.7” Optrex 320x240 55264GD057J-FW-ABN
5.7” TOSHIBA 320x240 LTA057A343F
5.7” Sharp 320x240 (QVGA / VGA) LQ057Q3DC02
5.7” Kyocera 320x240 (QVGA / VGA) TCG057QV1AC-G10
5.7” PVI 320x240 (QVGA / VGA) PD057VU4 /U5
5.7” Data image 640x480 FG050710DSSWJG01/DG01
5.7” Ampire 640x480 AM-640480GTMQW-T00H
5.7” URT 640x480 UMSH-8004MD-T
5.7” Sharp 640x480 LQ057V3DG01
5.7” CPT 640x480 CLAA057VA01
6.4” PVI 640x480 V16C6448AC
6.4” LG-PHILIPS 640x480 LB064V02
6.4” PVI 640x480 PD064VT2 /VT4 /VT5
6.4” Sharp 640x480 LQ064V3DG01
7” AUO 800x480 C070VW02V0
7” Data image 800x480 FG0700A0DSSWBG01
7” LG-PHILIPS 800x480 (TFT 24 bits) LB070WV1
7” HITACHI 800x480 TX18D57VM2BAA
7” Samsung 800x480 LMS700KF05
7” PVI 800x480 PM070WL4
7” URT 800x480 UMSH-8173MD-1T
7” CHI HSIN 800x480 LW700AT9309
8” Sharp 640x480 LQ080V3DG01
Page 40
VDX-6326RD Vortex86DX 3.5” CPU Module
36
Size Brand Resolution Model No.
8” AUO 800x600 (TFT 24bits) A080SN01 V0
8.4” Sharp 800x600 LQ084S3DG01
10.4” PVI 640x480 PD104VT1/VT2
10.4” NEC 640x480 NL6448AC33-18
10.4” NEC 640x480 NL6448AC33-29
10.4” NEC 640x480 NL6448BC33-59
10.4” Sharp 640x480 LQ104V1DG51/DG61
10.4” Sharp 640x480 LQ10d368
11” Sharp 800x480 LQ110Y3DG01
12.1” NEC 800x600 NL8060BC31-01
Page 41
VDX-6326RD Vortex86DX 3.5” CPU Module
37
C. LVDS Flat Panel Support
Size Brand Resolution Model No.
3.5” PVI 640x480 PD035VL1
5” PVI 640x480 PD050VL1
6.5” AUO 640x480 G065VN01
8.4” AUO 800x600 G084SN03
8.9” AUO 1024x600 A089SW01
8.9” CPT 1024x600 CLAA089NA0ACW
8.9” HannStar 1024x600 HSD089IFW1
10.4” MITSUBISHI 800x600 AA104SG01
10.4” AUO 800x600 G104SN02
10.4” Sharp 800x600 LQ104S1LG61
12.1” MITSUBISHI 800x600 AA121SL03
12.1” AUO 800x600 G121SN01
15” AUO 1024x768 G150XG01
Page 42
VDX-6326RD Vortex86DX 3.5” CPU Module
38
D. Flat Panel Hardware Setting:
The Vortex86DX-6326RD offers the Hardware setting for the various TFT LCD Flat Panels
support and please make sure the jumper setting (J32~J38) before you connect the LCD.
Display type setup
Connector
LCD
1-2 2-3
J32
C
J34
C
J35
X X
J36
X X
J37
C
J38
C
Note: "C" means close; "X" means open
Page 43
VDX-6326RD Vortex86DX 3.5” CPU Module
39
E. Flat Panel Wiring and Lighting
Hardware
Before you connect the TFT LCD Flat Panel with Vortex86DX-6326RD, please make sure
that the input Voltage of LCD is 3.3V or Not
BIOS
Please contact or e-mail our regional sales to get the special BIOS for the any TFT LCD
Flat Panels.
Wiring LCD Cable
Please refer to Page 22 (J33: LCD connector) and Page 34~39. Or for more LCD lighting
and integration service, please contact our regional sales or mail to info@icop.com.tw ,if
you have any questions.
Page 44
VDX-6326RD Vortex86DX 3.5” CPU Module
40
F. TCP/IP library for DOS real mode
DSock is a TCP/IP library for DOS real mode, which is used by RSIP. It provides simple C
functions for programmer to write Internet applications. ICOP also provide Internet examples
using DSock: BOOTP/DHCP, FTP server, SMTP client/server, HTTP server, TELNET server,
Talk client/server, etc.
DSock provides a lot of example source code. Programmer can add Internet functions to their
project easily and save development time. With a utility "MakeROM”, programmer also can make
a ROM image to fit their application, those examples can be seen in the following Application
systems: Mity-Mite Serial Server, Web Camera Tiny Server and RSIP Serial Server.
DSock is free for All ICOP products using M6117D/Vortex86/Vortex86SX/Vortex86DX CPU and
ICOP also provide the business version of DSock for those customers who are using other x86
CPUs.
If you would like to use DSock or business version of DSock, Please mail to info@icop.com.tw or
contact your regional sales.
Please download the trial DSock software and Utilities from our website:
http://www.dmp.com.tw/tech/dmp-lib/dsock/
Page 45
VDX-6326RD Vortex86DX 3.5” CPU Module
41
G. BIOS Default setting
If the system cannot be booted after BIOS changes are made, Please follow below procedures in
order to restore the CMOS as default setting.
Press “End” Key, when the power on
Press <Del> to enter the AMI BIOS setup
Press “F9” to Load Optimized Defaults
Press “F10” to Save configuration changes and exit setup
Page 46
VDX-6326RD Vortex86DX 3.5” CPU Module
42
Warranty
This product is warranted to be in good working order for a period of one year from the date of
purchase. Should this product fail to be in good working order at any time during this period, we
will, at our option, replace or repair it at no additional charge except as set forth in the following
terms. This warranty does not apply to products damaged by misuse, modifications, accident or
disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other
incidental or consequential damage resulting from the use, misuse of, originality to use this
product. Vendor will not be liable for any claim made by any other related party. Return
authorization must be obtained from the vendor before returned merchandise will be accepted.
Authorization can be obtained by calling or faxing the vendor and requesting a Return
Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a
clear problem description.
Loading...