Page 1
Full 16-bit ISA Bus
VDX-6324RD
DM&P Vortex86DX 800MHz
Half-Size CPU Module
with 4S/4USB/VGA/LCD/LAN/GPIO/PWMx16
256MB DDR2 Onboard
User’s Manual
(Revision 1.2A)
Page 2
Copyright
The information in this manual is subject to change without notice for continuous improvement of
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracy that may be contained in this document and makes no commitment to update or to
keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part,
in any form or by any means without the prior written permission of the ICOP Technology Inc.
Copyright 2008 ICOP Technology Inc.
Manual No. IUM6324000-01 Ver.1.0A February, 2009
Manual No. IUM6324000-01 Ver.1.1A July, 2010
Manual No. IUM6324000-01 Ver.1.2A September, 2013
Trademarks Acknowledgment
Vortex86DX is the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties
and registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.
Page 3
T a b l e o f C o n t e n t s
T a b l e o f C o n t e n t s ............................................................. iii
C h a p t e r 1 Introduction……………………………………………1
1.1 Packing List ............................................................ 1
1.2 Product Description ................................................ 2
1.3 Specifications ......................................................... 3
1.4 Board Dimension .................................................... 5
C h a p t e r 2 Installation……………………………………………..6
2.1 Board Outline ......................................................... 6
2.2 Connectors & Jumpers Location .................... ........7
2.3 Connectors & Jumpers Summary ........................... 9
2.4 Pin Assignments & Jumper Settings ......................11
2.5 System Mapping ................................................... 22
2.6 Watchdog Timer ................................................... 25
2.7 GPIO .................................................................... 26
2.8 SPI flash ............................................................... 27
2.9 PWM .................................................................... 28
3.0 IDE to SD ............................................................. 29
C h a p t e r 3 Driver Installation……………………………………30
Appendix ………………………………………………………………..31
A. TFT Flat Panel Data Output ...................................... 31
B. TFT Flat Panel Support List ....................................... 32
C. LVDS Flat Panel Support List .................................... 34
D. Flat Panel Hardware Setting ..................................... 35
E. Flat Panel Wiring and Lighting .................................. 36
F. TCP/IP library for DOS real mode .............................. 37
G. BIOS Default Setting ................................................. 38
Warranty ............................................................................................ 39
Page 4
This page is blank
Page 5
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
1
C h a p t e r 1
Introduction
1.1 Packing List
Product Name Package
VDX-6324RD
Embedded Vortex86DX CPU All-in-One Board
RS232 cable x 3
PRINT cable x1
IDE cable x 1
USB cable x 2
(U SB port x 2
)
GPIO cable x 1
YKB for PS/2 Keyboard & Mouse x 1
Page 6
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
2
1.2 Product Description
The VDX-6324 family of low-power x86 embedded controller is designed to meet Half-Size
specification with full 16-bit ISA Bus, and integrated with the following features.
800MHz Vortex86DX System-On-Chip
VGA, TFT/LVDS LCD support up to
1280x1024 resolution
256 / 512MB DDR2 system memory
Enhanced IDE (UltraDMA-100/66/33)
10/100Mbps Ethernet
4 USB 2.0 (host)
Up to 4 serial ports
Parallel port
16-bit GPIOs
Onboard 4MB SPI Flash
PC/104-Plus expansion bus
Meet PC/104 stacking spec.
2 watchdog timer
16~24 PWM channels
JTAG interface
AMI BIOS
Single voltage +5V DC
Support extended operating
temperature range of -20°C to +70°C
The VDX-6324 Half-Size family of embedded controller is designed with backward compatibility
in mind, to provide migration path for projects facing end-of-life challenges with their existing x86
based Half-Size controller. The VDX-6324 family of controller is designed as a plug in
replacement, with backward compatibility to support legacy software to help extend existing
product life cycle without heavy re-engineering.
VDX-6324RD is suitable for broad range of data-acquisition, Industrial automation, Process
control, Automotive controller, AVL, Intelligent Vehicle management device, Medical device,
Human machine interface, Robotics, machinery control and more…application that required
small footprint, low-power and low-cost hardware with open industry standard such as Half-Size.
Page 7
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
3
1.3 Specifications
Features VDX-6324
CPU
DM&P SoC CPU Vortex86DX- 800MHz
Real Time Clock with Lithium Battery Backup
Cache
L1:16K I-Cache, 16K D-Cache, L2 Cache 128KB
BIOS
AMI BIOS
Bus Interface
PC/104 Standard Compliant (Optional: PCI-104)
System Memory
256 /512MB DDR2 onboard
Watchdog Timer
Software programmable from 30.5 us to 512 seconds x2
sets(Watchdog 1 fully compatible with M6117D)
VGA
XGI Volari Z9s Chipset
VGA and TFT Flat Panel Interface Support
LVDS Flat Panel Interface Support (Optional)
Onboard 32MB VGA Memory
Support resolution up to 1280 x 1024
LAN
Integrated 10/100M Ethernet
Audio
CM119 USB Audio Controller (Optional)
I /O Interface
Enhanced IDE port (UltraDMA-100/66/33) x1
RS-232 port x3
RS-232/422/485 port x1 (RS485 Auto Direction)
Parallel port x1
USB port (2.0) x4
16-bit GPIO port x1
10/100Mbps Ethernet port x1
Page 8
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
4
Connectors
2.54mm ∅ 26-pin box header for Print x1
2.54mm ∅ 10-pin box header for RS-232 x3
2.54mm ∅ 10-pin box header for USB x2
2.54mm ∅ 20-pin box header for 16-bit GPIO x1
2.54mm ∅ 3-pin header for RS-485 x1
2.54mm ∅ 2-pin header for Reset x1
2.54mm 4-pin header for DC-in x1
2.54mm 7-pin header for Redundancy Signal x1(O)
2.54mm 2-pin header for SYS-SW-IN x1 (Opt)
2.0mm ∅ 44-pin box header for IDE x1
2.0mm ∅ 44-pin box header for LCD x1
1.25mm ∅ 6-pin Wafer for JTAG x1
1.25mm ∅ 4-pin Wafer for Line-out/MIC-in x2 (O)
External RJ-45 connector for Ethernet x1
External Mini DIN connector for KBD/Mouse x1
External D-Sub 15 pin female connector for VGA x1
External D-Sub 9 pin male connector for RS232 x1
Type I/II Compact Flash Slot x1
4-pin Male Power Connector x1
Flash Disk Support
On board 4MB SPI Flash Disk (Driver: A)
44-pin IDE Flash Disk( EmbedDisk 16MB or above)
Compact Flash Type I/II
44-pin IDE to Micro SD (Optional)
PWM
16~24 Channels
SRAM support
512KB (Optional)
Power Requi rement
Single Voltage +5V
@
760mA
Dimension
184mm X 122mm (7.24 x4.80 inches)
Weight
180g
Operating
Temperature
-20oC ~ +70oC
-40°C ~ +85°C (Optional)
Page 9
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
5
1.4 Board Dimension
Page 10
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
6
C h a p t e r 2
C h a p t e r 2C h a p t e r 2
C h a p t e r 2
Installation
2.1 Board Outline
COM4 COM3
COM2
RS-232/422/485
GPIO
LCD
Connector
Display Type
Selection
RS-485
Power
Connector
USB x 2
COM1
USB x 2
LAN
VGA
PS/2
KB/Mouse
Flexible DC
Power Connector
PC/104Power Connector
Parallel Port
JTAG
EIDE
Interface
Reset
(Note1: COM2 RS232/422/485 is selected by BIOS setting)
(Note2: J39 Default setting of JTAG Has to be Disable: Pin 1 & Pin 2 short)
(Note3: PCI-104 connector is optional: VI/O setting: +5V only)
(Note4: Redundancy Signal and System-Fail-SW are optional)
Page 11
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
7
2.2 Connectors & Jumpers Location
Connectors
Page 12
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
8
Jumpers & LEDs
Page 13
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
9
2.3 Connectors & Jumpers Summary
Summary Table
Nbr
Description Type of Connections Pin nbrs.
J1 IDE Box Header, 2.0∅ , 22x2 44-pin
J2 USB1 Box Header, 2.54∅ , 5x2 10-pin
J3 USB2 Box Header, 2.54∅ , 5x2 10-pin
J4 JTAG Wafer, 1.25∅ , 6x1 6-pin
J5 Reset Pin Header, 2,54∅,1x2 2-pin
J6 Redundancy (Optional) Pin Header, 2.54∅, 7x1 7-pin
J7 System –Fail-Switch (Optional)
Pin Header, 2.54∅ , 2x1 2-pin
J8 PS/2 Keyboard & Mouse Mini-Din Connector 6-pin
J9 COM1(TTL/GPIO-P4 / PWMx8)
D-Sub Connector 9-pin
J10
COM2(RS232/422/485) Box Header, 2.54∅ 5x2 10-pin
J11
GPIO ( Port 0 / 1 /PWMx16) Box Header, 2.54∅ ,10x2 20-pin
J12
RS-485 Molex Header,2.54∅ , 3x1 3-pin
J17
Power Connector Box Header, 5.0∅ Molex 4-pin
J18
Power Connector Terminal Block 5.0∅,2x1 2-pin
J19
COM3 Box Header, 2.54∅, 5x2 10-pin
J20
PRINT Box Header, 2.54∅ ,13x2 26-pin
J21
COM4 Box Header, 2.54∅, 5x2 10-pin
J22
PC104 Connector – 64 pin Box Header, 2.54∅ 32x2 64-pin
J24
PC104 Connector – 40 pin Box Header, 2.54∅ ,20x2 40-pin
J26 4P Power Source (Interconnect
to PC/104 – J22)
Pin Header, 2.54∅ , 4x1 4-pin
J27
PC/104 + (Optional) Box Header, 2.0∅ , 30x4 120-pin
J28 VGA D-Sub female connector 15-pin
J29
LCD Box Header,2.0∅ ,22x2 44-pin
J30
J35
Display type Setup Pin Header, 2.54∅ , 3x1 3-pin
J36 10/100Base-T Ethernet LAN RJ45 Connector 8-pin
J37
LINE-OUT (Optional) Wafer, 1.25∅ , 4x1 4-pin
J38
MIC-IN (Optional) Wafer, 1.25∅ , 4x1 4-pin
J39 JTAG Disable (Default setting)
Pin Header, 2,54∅,1x2 2-pin
J40 Master/Slave for IDE & CF Slide Switch 3-pin
Page 14
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
10
J41 Console Redirection (Optional)
Pin Header, 2,54∅,1x2 2-pin
PWR-L
ED
Power Active LED (Red) LED-SMD
IDELED
IDE Active LED (Green ) LED-SMD
MTBF-
LED
MTBF-Out (Orange) LED-SMD
CF1 Compact Flash Type I/II CF Connector 50-pin
SP1 BUZZER
Page 15
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
11
2.4 Pin Assignments & Jumper Settings
J1: IDE (44 Pins)
J2: USB 1
Pin # Signal Name Pin # Signal Name
1 VCC
2
VCC
3 LUSBD
0- 4
LUSBD
1-
5 LUSBD
0+ 6 LUSBD
1+
7 GND
8
GND
9 G
GND
10 GGND
Pin # Signal Name Pin # Signal Name
1 IDERST
2
GND
3 IDED7
4
IDED8
5 IDED6
6
IDED9
7 IDED5
8
IDED10
9 IDED4
10
IDED11
11 IDED3
12
IDED12
13 IDED2
14
IDED13
15 IDED1
16
IDED14
17 IDED0
18
IDED15
19 GND
20 NC
21 IDEREQ
22
GND
23 IDEIOW
24
GND
25 IDEIOR
26
GND
27 ICHRDY
28
GND
29 IDEACK
30
GND
31 IDEINT
32 NC
33 IDESA1
34
IDECBLID
35 IDESA0
36
IDESA2
37 IDECS
-0 38
IDECS1
39 IDELED
40
GND
41 VCC
42
VCC
43 GND
44 NC
Page 16
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
12
J3: USB 2
Pin # Signal Name Pin # Signal Name
1 VCC
2
VCC
3 LUSBD
2- 4
LUSBD
3-
5 LUSBD
2+ 6 LUSBD
3+
7 GND
8
GND
9 G
GND
10 GGND
J4: JTAG
Pin # Signal Name Pin # Signal Name
1 VCC 2 GND
3 TCK 4 TDO
5 TDI 6 TMS
J5: RESET
Pin # Signal Name Pin # Signal Name
1 Reset 2 GND
J6: Redundancy (Optional)
Pin # Signal Name Pin # Signal Name
1 GND 2 SYS-FAIL-OUT
3 SYS-FAIL-IN 4 GPCS0
5 SYS-GPCS-IN
6 TXD9\
7 RXD9\
J7: System-Fail-Switch (Optional)
Pin # Signal Name
1 SYS
-SW-IN
2 GND
Page 17
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
13
J8: PS/2 KBD / Mouse
Pin # Signal Name Pin # Signal Name
1 KBCLK
2 MSCLK
3 GND
4
KBDAT
5 MSDAT
6
VCC
7 GND
8
GND
9 GND
J9: COM 1 (Optional: TTL/ GPIO-P4 / PWMx8)
Pin #
Signal
Name
Pin #
Signal
Name
1 DCD1
2 RXD1
3 TXD1
4 DTR1
5 GND 6 DSR1
7 RTS1
8 CTS1
9 RI1 10 GND
11 GND
J10: COM2 RS232 / RS422 / RS485 (Optional: TTL)
Pin #
Signal Name Pin #
Signal Name
1 DCD2/ 422TX- / RS485-
2 RXD2 / 422TX+ / RS485+
3 TXD2 / 422RX+ 4 DTR2 / 422RX-
5 GND 6 DSR2
7 RTS2 8 CTS2
9 RI2 10 NC
Page 18
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
14
J11: GPIO (Port 0 / Port 1/PWMx16)
J12: RS485 (Auto direction)
J17: Power Connector – 4-pin Header (P4 Molex 5mm)
Pin #
Signal
Name
1 +5V
2 GND
3 GND
4 +12V
Pin # Signal Name Pin # Signal Name
1 GND 2 VCC
3 GP00 4 GP10
5 GP01 6 GP11
7 GP02 8 GP12
9 GP03 10
GP13
11 GP04 12
GP14
13 GP05 14
GP15
15 GP06 16
GP16
17 GP07 18
GP17
19 VCC 20
GND
Pin # Signal Name
1 RS485＋
2 RS485－
3 GND
Page 19
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
15
J18: Power Connector (Terminal Block 5.0mm)
Pin # Signal Name
1 +5V
2 GND
J19: COM3 (Optional: TTL)
Pin # Signal Name Pin # Signal Name
1 DCD3 2 RXD3
3 TXD3 4 DTR3
5 GND 6 DSR3
7 RTS3 8 CTS3
9 RI3 10
NC
J20: PRINT
Pin # Signal Name Pin # Signal Name
1 STB- 14
AFD-
2 PD0 15
ERR-
3 PD1 16
INIT-
4 PD2 17
SLIN-
5 PD3 18
GND
6 PD4 19
GND
7 PD5 20
GND
8 PD6 21
GND
9 PD7 22
GND
10 ACK- 23
GND
11 BUSY 24
GND
12 PE 25
GND
13 SLCT 26
NC
J21: COM4 (Optional: TTL)
Pin # Signal Name Pin # Signal Name
1 DCD4 2 RXD4
3 TXD4 4 DTR4
5 GND 6 DSR4
7 RTS4 8 CTS4
9 RI4 10
NC
Page 20
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
16
J22: PC104 Connector – 64pin
Pin # Signal Name Pin # Signal Name
1 IOCHCHK *
2
GND
3 SD7
4
RESETDRV
5 SD6
6
VCC
7 SD5
8
IRQ9
9 SD4
10 -5V
11 SD3
12 DRQ2
13 SD2
14 -12V
15 SD1
16
OWS
17 SD0
18
+12V
19 IOCHRDY
20
GND
21 AEN
22
SMEMW *
23 SA19
24
SMEMR *
25 SA18
26
IOW *
27 SA17
28
IOR *
29 SA16
30
DACK3 *
31 SA15
32
DRQ3
33 SA14
34
DACK1 *
35 SA13
36
DRQ1
37 SA12
38
REFRESH *
39 SA11
40
SYSCLK
41 SA10
42
IRQ7
43 SA9
44
IRQ6
45 SA8
46
IRQ5
47 SA7
48
IRQ4
49 SA6
50
IRQ3
51 SA5
52
DACK2 *
53 SA4
54 TC
55 SA3
56 BALE
57 SA2
58
VCC
59 SA1 60
OSC
61 SA0
62
GND
63 GND
64
GND
Page 21
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
17
J24: PC104 Connector – 40pin
J26: 4P Power Source (Interconnect to PC/104 – J22)
Pin # Signal Name
1 -5V
2 -12V
3 +12V
4 GND
Pin # Signal Name Pin # Signal Name
1 GND
2
GND
3 MEMCS16 *
4
SBHE *
5 IOCS16 *
6 SA23
7 IRQ10
8 SA22
9 IRQ11
10 SA21
11 IRQ12
12 SA20
13 IRQ15
14 SA19
15 IRQ14
16 SA18
17 DACK0
* 18 SA17
19 DRQ0
20
MEMR *
21 DACK5 *
22
MEMW *
23 DRQ5
24
SD8
25 DACK6 *
26
SD9
27 DRQ6
28
SD10
29 DACK7 *
30
SD11
31 DRQ7
32
SD12
33 VCC
34
SD13
35 MASTER *
36
SD14
37 GND
38
SD15
39 GND
40 NC
Page 22
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
18
J27: PC/104 + (Optional)
VI/O setting: +5V only
If you need to use VI/O as +3.3V, please use VDX-6324-FD-Plus
Pin # A B C D
1 GND
NC
+5V
AD00
2 VI/O(+5V
) AD02
AD01
+5V
3 AD05
GND
AD04
AD03
4 C
/BE0#
AD07
GND
AD06
5 GND
AD09
AD08
GND
6 AD11
VI/O(+5V)
AD10
GND
7 AD14
AD13
GND
AD12
8 +3.3V
C/BE1#
AD15
+3.3V
9 SERR#
GND
NC
PAR
10 GND
PERR#
+3.3V
NC
11 STOP#
+3.3V
LOCK#
GND
12 +3.3V
TRDY#
GND
DEVSEL#
13 FRAME#
GND
IRDY#
+3.3V
14 GND
AD16
+3.3V C/BE2#
15 AD18
+3.3V
AD17
GND
16 AD21
AD20
GND
AD19
17 +3.3V
AD23
AD22
+3.3V
18 IDSEL0
GND
IDSEL1
IDSEL2
19 AD24
C/BE3#
VI/O(+5V)
IDSEL3
20 GND
AD26
AD25
GND
21 AD29
+5V
AD28
AD27
22 +5V
AD30
GND
AD31
23 REQ0#
GND
REQ1#
VI/O(+5V)
24 GND
REQ2#
+5V
GNT0#
25 GNT1#
VI/O(+5V)
GNT2#
GND
26 +5V
CLK0
GND
CLK1
27 CLK2
+5V
CLK3
GND
28 GND
INTD#
+5V
RST#
29 +12V
INTA#
INTB#
INTC#
30 -
12V
NC NC
GND
Page 23
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
19
J28: VGA (D-Sub connector)
Pin # Signal Name Pin # Signal Name
1 R OUT 2 G OUT
3 B OUT 4 NC
5 GND 6 GND
7 GND 8 GND
9 VCC 10
GND
11 NC 12
DDCDAT
13 HSYNC 14
VSYNC
15 DDCCLK
J29: LCD Connector
Pin # Signal Name Pin # Signal Name
1 +3.3V 2 +3.3V
3 LG2 4 LG3
5 LG4 6 LG5
7 NC 8 NC
9 LR0 10
LR1
11 LR2 12
LR3
13 LR4 14
LR5
15 GND 16
NC
17 NC 18
NC
19 NC 20
GND
21 NC 22
NC
23 LB0 24
LB1
25 LB2 26
LB3
27 LB4 28
LB5
29 NC 30
NC
31 LG0 32
LG1
33 GND 34
GND
35 NC 36
LCLK
37 NC 38
LDE
39 NC 40
LHSYNC
41 NC 42
LVSYNC
43
LBACKL 44
LVDDEN
(Please refer to Appendix A, for TFT Flat Panel Data Output)
Page 24
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
20
J30~J35: Display type setup (CRT /LCD)
Connector
Pin # Signal Name
J30
1 VCC
2 GPIOA
3 GND
J31
1 VCC
2 GPIOB
3 GND
J32
1 VCC
2 GPIOC
3 GND
J33
1 VCC
2 GPIOD
3 GND
J34
1 VCC
2 GPIOE
3 GND
J35
1 VCC
2 GPIOF
3 GND
(Please refer to Appendix D, for Display type setup)
J36: LAN
Pin # Signal Name Pin # Signal Name
1 TD+ 2 TD3 RO+ 4 NC
5 NC 6 RO7 NC 8 NC
Page 25
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
21
J37: LINE OUT (Optional)
Pin # Signal Name
1 LOUTR
2 GND
3 GND
4 LOUTL
J38: MIC-IN (Optional)
Pin # Signal Name
1 MICVREF
2 GND
3 GND
4 MIC-IN
J39: JTAG Disable (Default setting Pin 1 & Pin 2 short)
Pin # Signal Name Pin # Signal Name
1 GND 2 JTAG Disable
J41: Console Redirection (Optional: Pin 1 & Pin 2 short)
Pin # Signal Name Pin # Signal Name
1 Console_Red 2 GND
Page 26
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
22
2.5 System Mapping
Page 27
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
23
Page 28
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
24
Page 29
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
25
2.6 Watchdog Timer
There are two watchdog timers in Vortex86SX/DX CPU. One is compatible with M6117D
watchdog timer and the other is new. The M6117D compatible watchdog timer is called WDT0
and the new one is called WDT1.
We also provide DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech or download the PDF file:
http://www.dmp.com.tw/tech/vortex86dx/
Page 30
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
26
2.7 GPIO (General Purpose Input / Output)
40 GPIO pins are provided by the Vortex86SX/DX for general usage in the system. All GPIO pins
are independent and can be configured as inputs or outputs, with or without pull-up/pull-down
resistors.
We also offer DOS, Linux and WinCE example for your reference. For more technical support,
please visit: http://www.dmp.com.tw/tech or download the PDF file:
http://www.dmp.com.tw/tech/vortex86dx/
Page 31
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
27
2.8 SPI flash (Serial Peripheral Interface)
As SPI Flash (Serial Peripheral Interface) offers many benefits including: reduced controller pin
count, smaller and simpler PCBs, reduced switching noise, less power consumption, and lower
system cost
Many of users may consider using a formatted SPI flash to boot for the system or emulate SPI
flash as Floppy (A: Driver or B: Driver). Then you must know how to set for this condition in
CMOS Setup and boot up under DOS 6.22, X-DOS, DR-DOS and Free DOS.
For more technical support, please visit: http://www.dmp.com.tw/tech or download the PDF file:
http://www.dmp.com.tw/tech/vortex86dx/
Page 32
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
28
2.9 PWM (Pulse-width modulation)
Pulse-width modulation (PWM) of a signal or power source involves the modulation of its duty
cycle, to either convey information over a communications channel or control the amount of
power sent to a load.
The popular applications of pulse width modulation are in speed control of electric motors,
volume control of Class D audio amplifiers or brightness control of light sources and many other
power electronics applications.
The Vortex86DX SoC integrated 32 channels of PWM interface enabling the Automation, robotic
industry to a New Age x86 SoC platform and we also offer the sample code of PWM which will
guide the engineer to control the PWM functionality smoothly.
For more inquire of this sample code that please contact our sales team or mail to:
info@icop.com.tw
Page 33
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
29
3.0 IDE to SD (Micro-SD)
Vortex86DX SoC also built-in simulation circuit to adapt SD to IDE in order to allow your system
to recognize Micro-SD card as C: or D: Driver
SD-1917: 44 pins IDE to SD Adapter is an ideal solution for industrial PC or embedded system
and 44 pins IDE to SD Adapter can be easily installed on all VDX-63xx CPU boards. You or your
customers just do the BIOS setting and use SD-1917 to connect IDE connector of VDX-63xx
directly.
For further inquiries of SD-1917, please contact ICOP sales team or mail to: info@icop.com.tw
for your request.
<BIOS setting>
Get into the BIOS setup Utility
Choose Primary IDE Pin Select: SD card
Press “F10” to Save configuration changes and exit setup
SD-1917:
http://www.icop.com.tw/pddetail.aspx?id=125&pid=4
SD-1917
Page 34
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
30
C h a p t e r 3
C h a p t e r 3C h a p t e r 3
C h a p t e r 3
Driver Installation
VGA
The Vortex86DX processor also use external Display chip ““Volari™ Z9s” which is an ultra low
powered graphics chipset with total power consumption at around 1-1.5 W. It is capable in
providing VGA display output upto 1600x1200. With DVO interface, developers could easily
connect flat Panel to support TFT and LVDS output.
LAN
The Vortex86DX processor also integrated 10/100Mbps Ethernet controller that supports both
10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area
Network for full interaction with local servers, wide area networks such as the Internet.
The controller supports: Half / Full-Duplex Ethernet function to double channel bandwidth, auto
media detection.
Operating system support
The VDX-6324RD ISA CPU board supports Embedded software: Free DOS, DOS 6.22, PCDOS
7.1, DR-DOS,x-DOS,OS/2,Windows CE 6.0, Windows 98, Windows XP Professional, Windows
Embedded standard (XPE) and Windows 2000 (SP4).
Please download the drivers for VDX-6324RD board on ICOP official website:
http://www.icop.com.tw/en/product/Half-Size-SBC-VDX-6324D-800M
Hz/VDX-6324D.html
VDX-6324RD also supports most of the popular Linux distributions, for more detail information,
please visit DMP official website: http://www.dmp.com.tw/tech/vortex86dx/
.
Page 35
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
31
Appendix
A. TFT Flat Panel Data Output
Page 36
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
32
B. TFT Flat Panel Support List
Size Brand Resolution Model No.
5.7” Data image 320x240 FG050701DSSWBG01
5.7” Optrex 320x240 55264GD057J-FW-ABN
5.7” TOSHIBA 320x240 LTA057A343F
5.7” Sharp 320x240 (QVGA / VGA) LQ057Q3DC02
5.7” Kyocera 320x240 (QVGA / VGA) TCG057QV1AC-G10
5.7” PVI 320x240 (QVGA / VGA) PD057VU4 /U5
5.7” Data image 640x480 FG050710DSSWJG01/DG01
5.7” Ampire 640x480 AM-640480GTMQW-T00H
5.7” URT 640x480 UMSH-8004MD-T
5.7” Sharp 640x480 LQ057V3DG01
5.7” CPT 640x480 CLAA057VA01
6.4” PVI 640x480 V16C6448AC
6.4” LG-PHILIPS 640x480 LB064V02
6.4” PVI 640x480 PD064VT2 /VT4 /VT5
6.4” Sharp 640x480 LQ064V3DG01
7” AUO 800x480 C070VW02V0
7” Data image 800x480 FG0700A0DSSWBG01
7” LG-PHILIPS 800x480 (TFT 24 bits) LB070WV1
7” HITACHI 800x480 TX18D57VM2BAA
7” Samsung 800x480 LMS700KF05
7” PVI 800x480 PM070WL4
7” URT 800x480 UMSH-8173MD-1T
8” Sharp 640x480 LQ080V3DG01
8” AUO 800x600 (TFT 24bits) A080SN01 V0
Page 37
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
33
Page 38
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
34
Size Brand Resolution Model No.
8” AUO 800x600 (TFT 24bits) A080SN01 V0
8.4” Sharp 800x600 LQ084S3DG01
10.4” PVI 640x480 PD104VT1/VT2
10.4” NEC 640x480 NL6448AC33-18
10.4” NEC 640x480 NL6448AC33-29
10.4” NEC 640x480 NL6448BC33-59
10.4” Sharp 640x480 LQ104V1DG51/DG61
10.4” Sharp 640x480 LQ10d368
11” Sharp 800x480 LQ110Y3DG01
12.1” NEC 800x600 NL8060BC31-01
Page 39
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
35
C. LVDS Flat Panel Support List
If you would like to use LVDS Flat Panel with Vortex86SX / Vortex86DX series, please contact
our regional sales to get ICOP-0096 information or visit ICOP website:
http://www.icop.com.tw/pddetail.aspx?id=65&pid=4
ICOP–0096
: 18-bit TFT to LVDS converter and Cable-LVDS-30: LVDS Cable 30cm
Approved LVDS Flat Panel List
Size Brand Resolution Model No.
3.5” PVI 640x480 PD035VL1
5” PVI 640x480 PD050VL1
6.5” AUO 640x480 G065VN01
8.4” AUO 800x600 G084SN03
8.9” AUO 1024x600 A089SW01
8.9” CPT 1024x600 CLAA089NA0ACW
10.4” AUO 800x600 G104SN02
12.1” AUO 800x600 G121SN01
15” AUO 1024x768 G150XG01
Page 40
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
36
D. Flat Panel Hardware Setting:
The VDX-6324RD offers the Hardware setting for the various TFT LCD Flat Panels support and
please make sure the jumper setting (J30~J35) before you connect the LCD.
Display type setup
Connector
LCD
1-2 2-3
J30
C
J31
C
J32
X X
J33
X X
J34
C
J35
C
Note: "C" means close;
"X" means open
Page 41
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
37
E. Flat Panel Wiring and Lighting
Hardware
Before you connect the TFT LCD Flat Panel with VDX-6324RD, please make sure
that the input Voltage of LCD is +3.3V.
BIOS
Please contact or e-mail our regional sales to get the special BIOS for any TFT LCD
Flat Panels.
Wiring LCD Cable
Please refer to Page 19 (J29: LCD connector) and Page 31~36. Or for more LCD lighting
and integration service, please contact our regional sales or mail to info@icop.com.tw ,if
you have any questions.
Page 42
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
38
F. TCP/IP library for DOS real mode
DSock is a TCP/IP library for DOS real mode, which is used by RSIP. It provides simple C
functions for programmer to write Internet applications. ICOP also provide Internet examples
using DSock: BOOTP/DHCP, FTP server, SMTP client/server, HTTP server, TELNET server,
Talk client/server, etc.
DSock provides a lot of example source code. Programmer can add Internet functions to their
project easily and save development time. With a utility "MakeROM”, programmer also can make
a ROM image to fit their application, those examples can be seen in the following Application
systems: Mity-Mite Serial Server, Web Camera Tiny Server and RSIP Serial Server.
DSock is free for All ICOP products using M6117D/Vortex86/Vortex86SX/Vortex86DX CPU and
ICOP also provide the business version of DSock for those customers who are using other x86
CPUs.
If you would like to use DSock or business version of DSock, Please mail to info@icop.com.tw or
contact your regional sales.
Please download the trial DSock software and Utilities from our website:
http://www.dmp.com.tw/tech/dmp-lib/dsock/
Page 43
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
39
G. BIOS Default setting
If the system cannot be booted after BIOS changes are made, Please follow below procedures in
order to restore the CMOS as default setting.
Press “End” Key, when the power on
Press <Del> to enter the AMI BIOS setup
Press “F9” to Load Optimized Defaults
Press “F10” to Save configuration changes and exit setup
Page 44
Vortex86DX-6324RD Vortex86DX Half-Size CPU Module
40
Warranty
This product is warranted to be in good working order for a period of one year from the date of purchase.
Should this product fail to be in good working order at any time during this period, we will, at our option,
replace or repair it at no additional charge except as set forth in the following terms. This warranty does not
apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for
any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the
use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other
related party. Return authorization must be obtained from the vendor before returned merchandise will be
accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return
Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear
problem description.
Loading...