ICOP PDX2-057T-5A, PDX2-057T-8A, PDX2-057T-5A-2G, PDX2-057T-8A-2G User Manual

i

DM&P Vortex86DX2 P anel PC

with 5.7” TFT LCD

 Model:

PDX2-057T-5A / PDX2-057T-8A
PDX2-057T-5A-2G / PDX2-057T-8A-2G

User’s Manual

(Revision 1.1A)

i

Revision

Date Version Description

2016/11/18 Version 1.0 Initial Release

2017/01/10 Version 1.1 Specification correction

ii

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

Copyright

The information in this manual is subject to change without notice for
continuous improvement in the product. All rights are reserved. The manufacturer
assumes no responsibility for any inaccuracies that may be contained in this
document. And makes no commitment to update or to keep current the
information contained in this manual.

No part of this manual may be reproduced, copied, translated or transmitted,
in whole or in part, in any form or by any means without the prior written
permission of the ICOP Technology Inc.

Copyright 2017 ICOP Technology Inc.

Manual No. IUMPDX2057-01 Ver.1.1A Jan, 2017

Trademarks Acknowledgment

Vortex86DX2 is the registered trademark of DMP Electronics Inc. Other
brand names or product names appearing in this document are the properties and
registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.

Safety Information

 Read these Safety instructions carefully.
 Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

 Do not expose your Panel PC to rain or moisture, in order to prevent shock

and fire hazard.

 Keep PDX2-057T away from humidity.
 Do not open the cabinet to avoid electrical shock. Refer to your nearest

dealer for qualified personnel servicing.

 Never touch un-insulated terminals or wire unless your power adaptor is

disconnected.

 Locate your Panel PC as close as possible to the socket outline for easy access

and to avoid force caused by entangling of your arms with surrounding cables
from the Panel PC.

 USB connectors are not supplied with Limited Power Sources.
 If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient overvoltage.

DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS (ENCASING) OF THIS

PRODUCT. PLEASE CONTACT YOUR DEALER FOR SERVICING FROM QUALIFIED TECHNICIAN.

iii

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

Table of Contents

Table of Contents ............................................................................................. iii

1 .General Information ............................................................................. 1

1.1 Product Description ............................................................ 1

1.2 Product Specification ......................................................... 2

1.3 Inspection standard for TFT-LCD Panel .............................. 4

1.4 Product Dimension ............................................................. 7

1.5 Ordering Information ......................................................... 8

1.6 Packing List ......................................................................... 9

2 .System Installation ............................................................................. 10

2.1 CPU Board Outline ............................................................ 10

2.2 Connector Summary......................................................... 11

2.3 Connector Pin Assignments .............................................. 12

2.4 External I/O Overview ...................................................... 14

2.5 External I/O Pin Assignment ............................................. 15

2.6 System Mapping ............................................................... 17

2.7 Watchdog Timer ............................................................... 20

3 .Driver Installation ............................................................................... 21

3.1 PDX2-057T Development Note ........................................ 22

3.2 BIOS Default setting ......................................................... 24

Warranty ......................................................................................................... 25

1

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

1 .G eneral Informat ion

1.1 Product Description

PDX2-057T is an ultra-compact platform for the present demanding

embedded and productive applications. It has new Vortex86DX2 SoC CPU which

consumes only minimum power requirement when running at 933MHz, and DDR2

memory provides faster data transfer rate. By using 5.7” TFT LCD, PDX2-057T

becomes the perfect choice for a limited budget. In additional, the integrated

10/100M Ethernet port supplies the communication capability which makes

PDX2-057T can be more widely used when running with Linux, Windows CE,

Windows XP, Windows 7, Windows Embedded environments to become the

perfect solution for system integration.

2

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

1.2 Product Specification

Table 1-1 Product Specification

CPU Board Specifications

CPU DM&P Vortex86DX2 - 933MHz

Cache

L1:16KB I-Cache, 16KB D-Cache

L2: 256KB Cache

BIOS AMI BIOS

Memory 1GB/2GB DDR2 onboard

Watchdog Timer

Software programmable from

30.5u to 512 seconds x 2 sets

LAN Integrated 10/100M Ethernet

Audio HD Audio-Realtek ALC262 CODEC

Internal Drives

Compact Flash Type I / II slot

Micro SD slot (Optional)

1GB or 2GB Flash Memory onboard (Optional)

I/O

RS-232/422/485 x 1

USB ports (Ver2.0) x 2

RJ-45 Port x 1

Mechanical & Environment

Power Requirement

Single Voltage +5VDC (PDX2-057T-5A)

Multi Voltage +8~+35VDC (PDX2-057T-8A )

Power Consumption 20W (Max.)

Operating

Temperature

0 ~ +50℃ ( 32 ~ +122℉)

/ -20~+60℃ ( -4 ~ +140℉) Optional & CPU down

to 800MHz (-I)

Storage Te mp .

-30 ~ +70℃ ( 14 ~ +158℉)

3

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

Operating Humidity 0% ~ 90% relative humidity, non-condensing

Dimensions 152 x 112 x 33mm (5.98 x 4.41 x 1.3 inches)

Weight 500g

Certification CE / FCC / VCCI / Vibration / Shock

LCD Specifications

Display Type 5.7” TFT LCD

Backlight Unit LED

Display Resolution 640(W) x 480(H)

Brightness (cd/m2) 500 nits

Contrast Ratio 300 : 1

Display Color 262, 144

Dot Pitch (mm) 0.06 (W) x 0.18 (H)

Viewing Angle

Vertical 100o,

Horizontal 140

o

Backlight Lifetime 50,000 hrs

Touchscreen

Type Analog Resistive

Resolution Continuous

Transmittance 80%

Controller PS / 2 interface

Software Driver

Linux, Win CE, Win XP, Win 7, Windows Embedded

Standard

Durability 1 million

4

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

1.3 Inspection standard for TFT-LCD Pane l

Table 1-2 Inspection Standard

DEFECT TYPE LIMIT Note

VISUAL
DEFECT

INTER

NAL

SPOT

φ＜0.15mm

Ignore

Note1

0.15mm≦φ≦0.5mm N≦4

0.5mm＜φ

N=0

FIBER

0.03mm<W≦0.1mm, L≦

5mm

N≦3

Note1

1.0mm＜W, 1.5mm＜L

N=0

POLARIZER

BUBBLE

φ＜0.15mm

Ignore

Note1

0.15mm≦φ≦0.5mm N≦2

0.5mm＜φ

N=0

Mura It’ OK if mura is slight visible through 6%ND filter

ELECTRICAL

DEFECT

BRIGHT DOT

A Grade B Grade

C

Area O Area

Total

C

Area O Area

Total

Note3

N≦0 N≦2 N≦2 N≦2 N≦3 N≦5

Note2

DARK DOT

N≦2 N≦3 N≦3 N≦3 N≦5 N≦8

TOTAL DOT

N≦4 N≦5 N≦6 N≦8

Note2

TWO ADJACENT DOT

N≦0

N≦1

pair

N≦1

pair

N≦1

pair

N≦1

pair

N≦1

pair

Note4

THREE OR MORE

ADJACENT DOT

NOT ALLOWED

LINE DEFECT NOT ALLOWED

(1) One pixel consists of 3 sub-pixels, including R, G, and B dot.

(Sub-pixel = Dot)

(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter

(3) If require G0 grand (Total dot N≦0), please contact region sales.

5

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

[Note 1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter.

1. White / Black Spot

2. Polarizer Bubble

Fig 1-1

Fig 1-2

[Note 2] Bright dot is defined through 6% transmission ND Filter as following.

Fig 1-3

6

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

[Note 3]

C Area: Center of display area

O Area: Outer of display area

[Note 4]

Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D

status) adjacent defect dots, including bright and dart adjacent dot. And they will

be counted 2 defect dots in total quantity.

R

RGG

R G

RRGG

R G

RRGG

R G

RRGG

R G

RRG

G

R G

RRG

G

R G

R

R

Defect Dot

Adjacent Dot

A

B

C

D

(1) The defects that are not defined above and considered to be problem shall

be reviewed and discussed by both parties.

Defects on the Black Matrix, out of Display area, are not considered as a defect or

counted.

7

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

1.4 Product Dimension

Fig 1-4 Product Dimension

8

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

1.5 Ordering Information

Table 1-3 Ordering Information

PART NUMBER DESCRIPTION

PDX2-057T-5A 5.7” Panel PC w/1GB DDR2

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

Power Adapter

PDX2-057T-8A 5.7” Panel PC w/1GB DDR2

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

8-35 DC Support

PDX2-057T-5A-2G 5.7” Panel PC w/2GB DDR2

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

Power Adapter

PDX2-057T-8A-2G 5.7” Panel PC w/2GB DDR2

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

8-35 DC Support

PDX2-057T-5A-I 5.7” Panel PC w/1GB DDR2 / Wide Temp.

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

Power Adapter

PDX2-057T-8A-I 5.7” Panel PC w/1GB DDR2 / Wide Temp.

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

8-35 DC Support

PDX2-057T-5A-2G-I 5.7” Panel PC w/2GB DDR2 / Wide Temp.

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

Power Adapter

PDX2-057T-8A-2G-I 5.7” Panel PC w/2GB DDR2 / Wide Temp.

/ 2USB / Line-Out / LAN / COM / CF / MicroSD /

8-35 DC Support

9

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

1.6 Packing List

Table 1-4 Packing List

PART NUMBER PACKAGE

PDX2-057T-5A PDX2-057T-5A Power-20W-3PIN

PDX2-057T-8A PDX2-057T-8A

PDX2-057T-5A-2G PDX2-057T-5A-2G Power-20W-3PIN

PDX2-057T-8A-2G PDX2-057T-8A-2G

PDX2-057T-5A-I PDX2-057T-5A-I Power-20W-3PIN

PDX2-057T-8A-I PDX2-057T-8A-I

PDX2-057T-5A-2G-I PDX2-057T-5A-2G-I Power-20W-3PIN

PDX2-057T-8A-2G-I PDX2-057T-8A-2G-I

WLAN KIT (Optional)

USB-WLAN-IPEX-KIT

WIRELESS-ANTENNA-157

WIRELESS-CABLE-150MM

10

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

2 .System Installation

2.1 CPU Board Outline

Fig 2-1 PDX2 CPU Board

11

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

2.2 Con nector Summary

Table 2-1 Summary Table

Nbr Description Type of Connections Pin nbrs.

J1 CF Master/Slave Switch Slide Switch ON/OFF

J3 USB External USB Connector 6-pin

J4 USB External USB Connector 6-pin

J5 USB (Optional) 2.0mm 5-pin wafer 5-pin

J8 PS/2 Keyboard 2.54mm 5-pin box header 5-pin

J9 PS/2Keyboard External Mini DIN Socket 6-pin

J10 COM1(RS232/422/485) External D-Sub Male Connector 9-pin

J14 VGA 2.0mm 10-pin box header 10-pin

J18 Micro SD Card Socket

(Optional)

Micro SD socket

J23 Audio Line-Out 1.25mm Phone Jack

J24 Audio Mic-In 2.0mm 4-pin wafer 4-pin

J25 COM3 (TX, RX) 1.25mm 3-pin wafer 3-pin

J26 COM4 (TX, RX) 1.25mm 3-pin wafer 3-pin

J30 SOM CPU Board Socket SOM CPU Board Socket 200-pin

J31 4-Wires Touch connector 1.25mm 4-pin wafer 4-pin

J32 USB (WLAN Optional) Internal USB Connector 6-pin

RJ45 Ethernet External RJ45 Connector 8-pin

PWR Power Connector (5A) External Mini DIN Socket 3-pin

PWR Power Connector (8A) External Power Plug 2-pin

CF1 CF Card Socket CF Type I/II Socket

12

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

2.3 Connector Pin Assignments

J1: CF Master/Slave Switch

J3: USB

Pin # Signal Name Pin # Signal Name

1 VCC 2 USBD2-

3 USBD2+ 4 GND

5 GND 6 GND

J4: USB

Pin # Signal Name Pin # Signal Name

1 VCC 2 USBD3-

3 USBD3+ 4 GND

5 GND 6 GND

J5: USB (Optional)

Pin # Signal Name

1 VCC

2 USBD1-

3 USBD1+

4 GND

5 GND

J8: PS/2 Keyboard

Pin # Signal Name Pin # Signal Name

1 KBCLK 2 KBD AT

3 NC 4 GND

5 VCC

J9: PS/2 Keyboard

Pin # Signal Name Pin # Signal Name

1 KBCLK 2 MSCLK

3 GND 4 KBD ATA

5 MS DATA 6 VCC

7 GND 8 GND

9 GND

J10: COM1 RS232/422/485

(Change setting by BIOS)

Pin # Signal Name Pin # Signal Name

1

DCD1/

422TX- /

RS485-

2

RXD1 /

422TX+ /

RS485+

3

TXD1 /

422RX+

4

DTR1 /

422RX-

5 GND 6 DSR1

7 RTS1 8 CTS1

9 RI1

Pin # Signal Name

On Master

OFF Slave

13

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

J14: VGA

Pin # Signal Name Pin # Signal Name

1 R OUT 2 GND

3 G OUT 4

GND

5 B OUT 6 GND

7 HSYNC 8 GND

9 VSYNCD 10 GND

J24: MIC-IN

Pin # Signal Name

1

MICVREF

2

GND

3 GND

4 MIC-IN

J25: COM3 (TX, RX)

Pin # Signal Name

1

GND

2

TXD3

3 RXD3

J26: COM4 (TX, RX)

Pin # Signal Name

1

GND

2

TXD4

3 RXD4

J31: 4-Wires Touch connector

Pin # Signal Name

1

Y-

2

X-

3 Y+

4 X+

J32: USB (WLAN Optional)

Pin # Signal Name Pin # Signal Name

1 VCC 2 USBD2-

3 USBD2+ 4 GND

5 GND 6 GND

PWR: Power Connector (5A)

Pin # Signal Name

1 +5V

2 GND

3 NC

4 GND

PWR: Power Connector (8A)

Pin # Signal Name

1 + 8 ~ 35V

2 GND

14

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

2.4 External I/O Overview

{ PDX2-057T-8A / PDX2-057T-8A-2G }

Fig 2-2 PDX2-057T-8A I/O overview

{ PDX2-057T-5A / PDX2-057T-5A-2G }

Fig 2-3 PDX2-057T-5A I/O overview

{Note}

1. WLAN is optional

2. COM1 RS232/422/485 is selected by BIOS setting

3. Micro SD Socket is optional (Either one of CF or Micro SD)

15

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

2.5 External I/O Pin Assignment

Power Switch

Pin # Status

| ON

O OFF

Power Connector (5A)

Pin # Signal Name

1 +5V

2 GND

3 NC

Power Connector (8A)

Pin # Signal Name

1 +8 ~ 35V

2 GND

Audio Line-Out

Pin # Signal Name

1 GND

2 LOUTL

3 Open Touch

4 Open Touch

5 VREFOUT

USB Port

Pin # Signal Name

1 VCC

2 USB0-

3 USB0+

4 GND

5 GGND

6 GGND

PS/2 Keyboard

Pin # Signal Name

1 KBCLK

2 PMCLK

3 GND

4 KBDAT

5 PMDAT

6 SB5V

16

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

J10: COM1 RS232/422/485 (Change setting by BIOS)

Pin # Signal Name Pin # Signal Name

1 DCD1/422TX-/RS485- 2 RXD1/422TX+/RS485+

3 TXD1 / 422RX+ 4 DTR1 / 422RX-

5 GND 6 DSR1

7 RTS1 8 CTS1

9 RI1

RJ45

Pin # Signal Name Pin # Signal Name

1 FTXD+ 2 FTXD-

3 FRXIN+ 4 NC

5 NC 6 FRXIN-

7 NC 8 NC

17

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

2.6 System Mapping

Table 2-2 Technical Data Sheet

System Mapping

Memory Mapping

Address Description Usage

00000000-0009FFFF System RAM *
000A0000-000AFFFF EGA/VGA Video Memory *

000B0000-000B7FFF MDA RAM, Hercules Graphics Display RAM *
000B8000-000BFFFF CGA Display RAM *

000C0000-000C7FFF EGA/VGA BIOS ROM *
000C8000-000CFFFF Boot ROM Enable
000CC000-000CFFFF Console Redirection Enable
000D0000-000DFFFF Expansion ROM Space
000E0000-000EFFFF USB Legacy SCSI ROM Space
000F0000-000FFFFF Motherboard BIOS *

FEBDE000-FEBDEFFF Standard OpenHCD USB Host Controller *
FEBDFC00-FEBDFCFF On board Ethernet Adapter *

I/O Mapping

I/O Address

Owner

Usage

0000h - 000Fh DMA 8237-1 *
0020h - 0021h PIC 8259-1 *

0022h - 0023h

Indirect Access Registers
( 6117D configuration port )

*

0040h - 0043h Timer counter 8254 *
0048h - 004Bh PWM counter 8254 *
0060h Keyboard / Mouse Data Port *

18

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

0061h Port B + NMI Control Port *
0062h - 0063h 8051 download 4K Address Counter *
0064h Keyboard / Mouse Status / Command Port *
0065h WatchDog0 Reload Counter *
0070h - 0071h CMOS RAM Port *
0072h - 0075h MTBF Control Register *
0078h - 007Ch GPIO Port 0,1,2,3,4 Default Setup *
0080h - 008Fh DMA Page Register *
0092h System Control Register *
0098h - 009Ch GPIO Direction Control *
00A0h - 00A1h PIC 8259-2 *
00A8h - 00ADh WatchDog1 Control Register *
00AEh WatchDog1 Reload Counter *
00C0h - 00DFh DMA 8237-2 *
00E0h - 00EFh DOS 4G Page Access *
0170h - 0177h IDE1 (IRQ 15) *
02E8h - 02EFh COM4 (IRQ 11)
02F8h - 02FFh COM2 (IRQ 3)
03E8h - 03EFh COM3 (IRQ 10)
03F6h IDE0 ATAPI Device Control Write only Register *
03F8h - 03FFh COM1 (IRQ 4) *
0480h - 048Fh DMA High Page Register *
0490h - 0499h Instruction Counter Register *
04D0h - 04D1h 8259 Edge,/ Level Control Register *
0CF8h - 0CFFh PCI configuration port *
D800h - D8FFh On Board LAN *

FC00h - FC05h

SPI Flash BIOS Control Register (internal SPI Flash
Base address)

*

19

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

IRQ Mapping

IRQ#

Description

Usage

IRQ0 System Timer *
IRQ1 Keyboard Controller *
IRQ2 Cascade for IRQ8 - 15
IRQ3 USB *
IRQ4 Serial Port 1 *
IRQ5 USB *
IRQ6 Unassigned
IRQ7 USB *
IRQ8 Real Time Clock *
IRQ9 Audio *
IRQ10 USB *
IRQ11 Ethernet 10/100M LAN *
IRQ12 Mouse *
IRQ13 Math Coprocessor *
IRQ14 Hard Disk Controller#1 *
IRQ15 Hard Disk Controller#2 *

DMA Mapping

DMA#

Description

Usage

DMA0
DMA1
DMA2 Floppy Disk Controller (Reserved)
DMA3
DMA5
DMA6
DMA7

20

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

2.7 Watchdog Timer

There are two watchdog timers in PDX2-057T, we also provide DOS, Linux and

WinCE example for your reference. For more technical support, please visit:

http://tech.icop.com.tw or download the PDF file:

dmp.com.tw/tech

21

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

3 .Driver Installation

VGA

The Vortex86DX2 processor is integrated RDC Display chip which is an ultra

low powered graphics chipset with total power consumption at around 1-1.5 W.

LAN

The Vortex86DX2 processor is integrated 10/100Mbps Ethernet controller

that supports both 10/100BASE-T and allows direct connection to your

10/100Mbps Ethernet based Local Area Network for full interaction with local

servers, wide area networks such as the Internet.

I/O and IRQ settings can be done by software with the supplied utility

software, or it can be set for Plug and Play compatibility. The controller supports:

Half / Full-Duplex Ethernet function to double channel bandwidth, auto media

detection.

AUDIO

The ALC262 series are 4-Channel High Definition Audio Codecs with UAA

(Universal Audio Architecture) featuring two 24-bit stereo DACs and three 20-bit

stereo ADCs, they are designed for high performance multimedia desktop and

laptop systems. The ALC262 series incorporates proprietary converter technology

to achieve over 100dB Signal-to-Noise ratio playback quality; easily meeting

PC2001 requirements and also bringing PC sound quality closer to consumer

electronic devices.

22

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

Operating system support

The PDX2-057T provides the VGA and LAN drivers for Linux, Windows CE,

Windows XP Professional, Windows 7, and Windows Embedded standard

(WES2009 / WES7).

Please get the drivers from ICOP official website: tech.icop.com.tw

PDX2-057T also supports most of the popular Linux distributions, for more

detail information, please visit DMP official website:

3.1 PDX2-057T Development Note

dmp.com.tw/tech/

<Primary IDE: Master or Slave>

1. Primary IDE Device can be either one of CF or Micro SD and the standard

version is for CF slot only.

2. CF Slot: Primary IDE: Master or Slave (User can use slide switch (in side of

CF slot) to adjust Master or Slave

3. Micro SD (Optional): Primary Master only

<Window CE6.0 and Compact 7 development guide>

Windows Embedded CE 6.0 and Compact 7 BSPs, trial CE image and

development notes, please visit technical website to get more

information:

tech.icop.com.tw

23

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

<Linux installation note>

Please forced the IDE setting in BIOS to PIO mode before install Linux

on PDX2-057T as follows:

Go to the advanced BIOS setting and make the “Onboard IDE Operate Mode”

is “Legacy Mode”

< Windows XP and Windows 7 installation note >

Please visit technical website to get more information:

tech.icop.com.tw

24

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

3.2 BIOS Default setting

If the system cannot be booted after BIOS changes are made, Please follow

below procedures in order to restore the CMOS as default setting.

Press < End > Key, when the power on

Press < Del > to enter the AMI BIOS setup

Press < F9 > to Load Optimized defaults

Press < F10 > to Save configuration changes and

exit setup

25

PDX2-057T DM&P Vortex86DX2 Panel PC with 5.7” VGA TFT LCD

Warranty

This product is warranted to be in good working order for a period of one

year from the date of purchase. Should this product fail to be in good working

order at any time during this period, we will, at our option, replace or repair it at

no additional charge except as set forth in the following terms. This warranty does

not apply to products damaged by misuse, modifications, accident or disaster.

Vendor assumes no liability for any damages, lost profits, lost savings or any other

incidental or consequential damage resulting from the use, misuse of, originality

to use this product. Vendor will not be liable for any claim made by any other

related party. Return authorization must be obtained from the vendor before

returned merchandise will be accepted. Authorization can be obtained by calling

or faxing the vendor and requesting a Return Merchandise Authorization (RMA)

number. Returned goods should always be accompanied by a clear problem

description.

All Trademarks appearing in this manuscript are registered trademark of their respective owners.

All Specifications are subject to change without notice.

©ICOP Technology Inc. 2017