ICOP PDX-089T-D5A-512, PDX-089T-D5A, PDX-089T-D8A, PDX-089T-D8A-512, PDX-089T-5A-512 User Manual

PDX-089T-D5A-512 / PDX-089T-D8A-512

PDX-089T-D5A / PDX-089T-D8A

DM&P Vortex86DX Panel PC

with 8.9” TFT LCD

User’s Manual

(Revision 1.1A)

ii

Copyright

The information in this manual is subject to change without notice for continuous improvement in
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracies that may be contained in this document. And makes no commitment to update or to
keep current the information contained in this manual.

No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part,
in any form or by any means without the prior written permission of the ICOP Technology Inc.

Copyright 2009 ICOP Technology Inc.
Manual No. IUMPDX089-01 Ver.1.2A

Feb, 2012

Trademarks Acknowledgment

Vortex86DX is the registered trademark of ICOP Technology Inc. Other brand names or
product names appearing in this document are the properties and registered trademarks of their
respective owners. All names mentioned herewith are served for identification purpose only.

iii

Safety Information

 Read these Safety instructions carefully.
 Make sure the voltage of the power source is correct before connecting the equipment to

the power outlet.

 Do not expose your Panel PC to rain or moisture, in order to prevent shock and fire

hazard.

 Keep PDX-089T away from humidity.
 Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for

qualified personnel servicing.

 Never touch un-insulated terminals or wire unless your power adaptor is disconnected.
 Locate your Panel PC as close as possible to the socket outline for easy access and to

avoid force caused by entangling of your arms with surrounding cables from the Panel
PC.

 USB connectors are not supplied with Limited Power Sources.
 If the equipment is not used for a long time, disconnect it from the power source to avoid

damage by transient overvoltage.

DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS

(ENCASING) OF THIS PRODUCT. PLEASE CONTACT YOUR DEALER FOR

SERVICING FROM QUALIFIED TECHNICIAN.

T a b l e o f C o n t e n t s

T a b l e o f C o n t e n t s ............................................................. iv

C h a p t e r 1 General Information..…………………………………1

1.1 Product Description ................................................ 1

1.2 Product Specifications ............................................ 2

1.3 Inspection standard for TFT-LCD panel .................. 4

1.4 Product Dimension ................................................. 7

1.5 Ordering Information .............................................. 8

1.6 Packing List ............................................................ 8

C h a p t e r 2 System Installation ................................................. 9

2.1 CPU Board Outline ................................................. 9

2.2 Connector Summary .............................................11

2.3 Connector Pin Assignments ................................. 12

2.4 External I/O Overview .......................................... 15

2.5 External I/O Pin Assignment ................................. 16

2.6 System Mapping ................................................... 18

2.7 Watchdog Timver ................................................. 18

C h a p t e r 3 Driver Installation…..………………………………..22

3.1 PDX-089T Development Note .............................. 23

3.2 BIOS Defaul Setting ............................................. 26

Warranty ............................................................................................ 27

v

This page is blank

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

1

C h a p t e r 1

General Information

1.1 Product Description

PDX-089T is an ultra compact platform for the present demanding embedded and productive

applications. It has new Vortex86DX SoC CPU which consumes only minimum power

requirement when running at 1GHz, and DDR2 memory provides faster data transfer rate. By

using 8.9” TFT LCD, PDX-089T becomes the perfect choice for a limited budget. In additional,

the integrated 10/100M Ethernet port supplies the communication capability which makes

PDX-089T can be more widely used when running with Linux, Windows CE, and Windows XP

environment to become the perfect solution for system integration.

 8.9” WSVGA TFT LCD
 4-Wire Resistive Touch Panel
 DM&P Vortex86DX SoC 1GHz
 256/512MB DDR2 system memory
 AMI BIOS
 2 watchdog timer
 Compact Flash Type I/II / Micro SD
 10/100Mbps Ethernet
 2 USB 2.0 (host)

 1 RS-232/485/422 ports
 Mini-PCI Socket (Wi-Fi Optional)
 Audio Out
 Single voltage +5V DC(5A Version)
 Multi voltage +8~+35V DC(8A Version)
 Fanless Design
 Operating temperature range of -20°C

to +60°

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

2

1.2 Product Specification

CPU Board Specifications

CPU

DM&P Vortex86DX 1GHz

Cache

L1:16KB I-Cache, 16KB D-Cache

L2: 128KB Cache

BIOS

AMI BIOS

Memory

256/512MB DDR2 onboard

Watchdog Timer

Software programmable from 30.5u to 512 seconds x 2 sets

LAN

Integrated 10/100M Ethernet

Audio

CM119 Line-Out

Internal Drives

Compact Flash Type I/II slot

Micro SD slot

I/O

RS-232/422/485 x 1

USB ports (Ver2.0) x 2

RJ-45 Port x 1

Expansion Slot

Mini-PCI socket x 1 (Internal)

Mechanical & Environment

Power Requirement

Single Voltage +5VDC ( 5A )

Multi Voltage +8~+35VDC ( 8A )

Power Consumption

1.3A@5VDC

Operating Temperature

-20 ~ +60 ℃ (-4 ~ +140 ℉)

Storage Temperature

-20 ~ +70 ℃ (-22 ~ +158 ℉)

Dimensions

236.6 x 146 x 35mm (9.31 x 5.75 x 1.38 inches)

Weight

468g

Front Panel Protection

IP 65

Certification

CE, FCC, VCCI, Vibration

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

3

LCD Specifications

Display Type

8.9” TFT LCD

Backlight Unit

LED

Display Resolution

1024(W) x 600(H)

Brightness (cd/m2)

220 nits

Contrast Ratio

500:1

Display Color

262,144

Pixel Pitch (mm)

190.5 (H) x 189 (V)

Viewing Angle

Vertical 110

o

,

Horizontal 140

o

Backlight Lifetime

25,000 hrs

Touchscreen

Type

Analog Resistive

Resolution

Continuous

Transmittance

80%

Controller

USB interface (RS-232 interface)

Software Driver

Linux/WinCE/WinXP

DOS(RS-232 interface only)

Durability

1 million

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

4

1.3 Inspection standard for TFT-LCD Panel

DEFECT TYPE LIMIT Note

VISUAL

DEFECT

INTERNAL

SPOT

φ＜0.15mm

Ignore

Note1

0.15mm≦φ≦0.5mm N≦4

0.5mm＜φ

N=0

FIBER

0.03mm<W

≦0.1mm, L≦5mm N≦3

Note1

1.0mm＜W, 1.5mm＜L

N=0

POLARIZER BUBBLE

φ＜0.15mm

Ignore

Note1

0.15mm≦φ≦0.5mm N≦2

0.5mm＜φ

N=0

Mura It’ OK if mura is slight visible through 6%ND filter

ELECTRICAL

DEFECT

BRIGHT DOT

A Grade B Grade

C Area O Area Total C Area O Area Total

Note3

N≦0 N≦2 N≦2 N≦2 N≦3 N≦5

Note2

DARK DOT

N≦2

N≦3 N≦3 N≦3 N≦5 N≦8

TOTAL DOT

N≦4 N≦5 N≦6 N≦8

Note2

TWO ADJACENT DOT

N≦0

N≦1

pair

N≦1

pair

N≦1

pair

N≦1

pair

N≦1

pair

Note4

THREE OR MORE

ADJACENT DOT

NOT ALLOWED

LINE DEFECT NOT ALLOWED

(1) One pixel consists of 3 sub-pixels, including R,G, and B dot.(Sub-pixel = Dot)

(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter

(3) If require G0 grand (Total dot N

≦0), please contact region sales.

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

5

[Note1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter

[Note2] Bright dot is defined through 6% transmission ND Filter as following.

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

6

[Note3]

C Area: Center of display area
C Area: Outer of display area

[Note4]

Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent

defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total

quantity.

(1) The defects that are not defined above and considered to be problem shall be reviewed and

discussed by both parties.

(2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted.

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

7

1.3 Product Dimension

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

8

1.4 Ordering Information

Part Number Description

PDX-089T-D5A-512 8.9” Panel PC w/512MB

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/Power Adapter

PDX-089T-D8A-512 8.9” Panel PC w/512MB

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/8-35 DC support

PDX-089T-D5A (BTO) 8.9” Panel PC w/256MB

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/Power Adapter

PDX-089T-D8A (BTO) 8.9” Panel PC w/256MB

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/8-35VDC support

1.5 Packing List

Part Number Package

PDX-089T-D5A-512

 PDX-089T-5A-512
 Power-20W-3PIN

PDX-089T-D8A-512

 PDX-089T-8A-512

PDX-089T-5DA (BTO)

 PDX-089T-5A
 Power-20W-3PIN

PDX-089T-D8A (BTO)

 PDX-089T-8A

WLAN KIT (Optional)

 MINI-PCI-WLAN-CARD
 WIRELESS-ANTENNA-157
 WIRELESS-CABLE-90MM

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

9

C h a p t e r 2

System Installation

2.1 CPU Board Outline

Bottom View

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

10

2.2 Connector Summary

Summary Table

Nbr Description Type of Connections Pin nbrs.

J1 CF Master/Slave Switch

Slide Switch On/OFF

J3 USB External USB Connector 6-pin
J4 USB External USB Connector 6-pin
J5 USB (Touchscreen) 2.0mm 5-pin wafer 5-pin
J6 J-TAG 1.25mm 6-pin wafer 6-pin
J8 PS/2 Keyboard 2.54mm 5-pin box header 5-pin
J9 PS/2 Keyboard/Mouse External Mini DIN Socket 6-pin

J10 COM1(RS232/422/485)

External D-Sub Male Connector 9-pin

J14 VGA 2.0mm 10-pin box header 10-pin
J27 LVDS connector 1.25mm WAFER20P 20-pin
J18 Micro SD Card Socket Micro SD socket 9-pin
J24 Audio Mic-In 2.0mm 4-pin wafer 4-pin

J29 Power/IDE LED 2.0mm 4-pin wafer 4-pin
RJ45 Ethernet External RJ45 Connector 8-pin
PWR Power Connector (5A) External Mini DIN Socket 3-pin
PWR Power Connector (8A) External Power Plug 2-pin

J23 Audio Line-Out 1.25mm Phone Jack

CF1 CF Card Socket CF Type I/II Socket

J13 Mini-PCI Socket Expansion Mini-PCI Socket

J18 Micro SD Card Socket Micro SD socket

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

11

2.3 Connector Pin Assignments

J1: CF Master/Slave Switch

J3: USB

Pin # Signal Name Pin # Signal Name

1 VCC 2 USBD2­3 USBD2+ 4 GND
5 GND 6 GND

J4: USB

Pin # Signal Name Pin # Signal Name

1 VCC 2 USBD3­3 USBD3+ 4 GND
5 GND 6 GND

J5: USB (Touchscreen)

Pin # Signal Name

1 VCC
2 USBD1­3 USBD1+
4 GND
5 GND

J6: J-TAG

Pin # Signal Name

1 VCC
2 GND
3 TCK
4 TDO
5 TDI
6 TMS

Pin # Signal Name

On Master

OFF Slave

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

12

J8: PS/2 Keyboard

Pin # Signal Name Pin # Signal Name

1 KBCLK 2 KBDAT
3 NC 4 GND
5 VCC

J9: PS/2 Keyboard/Mouse

Pin # Signal Name Pin # Signal Name

1 KBCLK 2 MSCLK
3 GND 4 KBDATA
5 MSDATA 6 VCC
7 GND 8 GND
9 GND

J10: COM1 RS232/422/48 5 (Change setting by BIOS)

Pin # Signal Name Pin #

Signal Name

1 DCD1/ 422TX- / RS485- 2 RXD1 / 422TX+ / RS485+

3 TXD1 / 422RX+ 4 DTR1 / 422RX-

5 GND 6 DSR1

7 RTS1 8 CTS1

9 RI1

J14: VGA

Pin #

Signal

Name

Pin #

Signal

Name

1 R OUT 2 GND
3 G OUT 4 GND
5 B OUT 6 GND
7 HSYNC 8 GND
9 VSYNCD 10 GND

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

13

J27: LVDS Connector

Pin # Signal Name

1 GND
2 3.3V
3 3.3V
4 BRIGHTNESS
5 TXOUT0­6 TXOUT0+
7 TXOUT1­8 TXOUT1+

9 GND
10 GND
11 TXOUT2­12 TXOUT2+
13 TXCLKOUT­14 TXCLKOUT+
15 GND
16 GND
17 5V
18 5V
19 NC
20 NC

J24: MIC-IN

Pin # Signal Name

1 MICVREF

2 GND

3 GND

4 MIC-IN

PWR: Power Connector (5A)

Pin # Signal Name

1 +5V

2 GND

3 NC

4 GND

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

14

PWR: Power Connector (8A)

Pin # Signal Name

1 + 8 ~ 35V

2 GND

J29: Power/IDE LED

Pin # Signal Name

1 PWRLEDP

2 PWRLEDN

3 IDELEDP

4 IDELEDN

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

15

2.4 External I/O Overview

(Note1: Wireless is opti onal)
(Note2: COM1 RS232/422/485 is selected by BIOS setting)

PDX-089T-D8A / PDX-089T-D8A-512 PDX-089T-D5A / PDX-089T-D5A-512

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

16

2.5 External I/O Pin Assignment

Power Switch

Pin # Status

| ON

O OFF

Power Connector (5A)

Pin #

Signal Name

1 +5V
2 GND
3 NC

Power Connector (8A)

Pin #

Signal Name

1 +8 ~ 35V
2 GND

J10: COM1 RS232/422/48 5 (Change setting by BIOS)

Pin # Signal Name Pin # Signal Name

1

DCD1/422TX-/RS485-

2 RXD1/422TX+/RS485+

3

TXD1 / 422RX+ 4 DTR1 / 422RX-

5

GND 6 DSR1

7

RTS1 8 CTS1

9

RI1

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

17

Audio Line-Out

Pin #

Signal

Name

1 GND
2 LOUTL
3 Open Touch
4 Open Touch
5 VREFOUT

USB

Pin # Signal Name

1 VCC
2 USB0­3 USB0+
4 GND
5 GGND
6 GGND

RJ45

Pin # Signal Name Pin # Signal Name

1 FTXD+ 2 FTXD­3 FRXIN+ 4 NC
5 NC 6 FRXIN­7 NC 8 NC

PS/2 Keyboard/Mouse

Pin # Signal Na me

1 KBCLK
2 PMCLK
3 GND
4 KBDAT
5 PMDAT
6 SB5V

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

18

2.6 System Mapping

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

19

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

20

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

21

2.7 Watchdog Timer

There are two watchdog timers in PDX-089T, we also provide DOS, Linux and WinCE example

for your reference. For more technical support, please visit: http://www.dmp.com.tw/tech

or

download the PDF file: http://www.dmp.com.tw/tech/vortex86dx/

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

22

C h a p t e r 3

Driver Installation

VGA

The Vortex86DX processor also use external Display chip ““Volari™ Z9s” which is an ultra low

powered graphics chipset with total power consumption at around 1-1.5 W.

LAN

The Vortex86DX processor also integrated 10/100Mbps Ethernet controller that supports both
10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area
Network for full interaction with local servers, wide area networks such as the Internet.
I/O and IRQ settings can be done by software with the supplied utility software, or it can be set
for Plug and Play compatibility. The controller supports: Half / Full-Duplex Ethernet function to
double channel bandwidth, auto media detection.

AUDIO

CM119 is a highly integrated single chip USB audio controller specifically for VoIP (Voice over
internet protocol) application. All essential analog modules are embedded in CM119, including
dual DAC and earphone driver, ADC, microphone booster, PLL, regulator, and USB transceiver.
8 GPIO pins can constitute a 24 key matrix directly support keypad control function without MCU.

Many features are programmable with jumper pins or external EEPROM. Vender can customize
unique USB VID/PID to EEPROM for VoIP software authentication. Moreover, individual unique
phone number for each device is possible via serial number stored in external EEPROM.

Operating system support

The PDX-089T provides the VGA and LAN drivers for Linux, Windows CE 5.0, CE 6.0, Windows

XP Professional, and Windows Embedded standard (XPE). (Linux can use with Compact

Flash card only.)

Please get the drivers from DMP official website: http://www.dmp.com.tw/tech/vortex86dx/

.

PDX-089T also supports most of the popular Linux distributions, for more detail information,
please visit DMP official website: http://www.dmp.com.tw/tech/vortex86dx/

.

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

23

3.1. PDX-089T Development Note

<Primary /Secondary IDE: Master or Slave>

Micro SD: Primary Master

CF Slot: Secondary IDE: Master or Slave (User can use slide switch (in side of CF
slot) to adjust Master or Slave

<Window CE6.0 development guide>

Windows Embedded CE 6.0 BSP, trial CE image and development notes, please visit
technical website to get more information: http://tech.icop.com.tw/

<Linux installation note>

Please forced the IDE setting in BIOS to PIO mode before install Linux
on PDX-089T as follows:
1-Go to the advanced BIOS setting and make the “Onboard IDE Operate Mode” is

“Legacy Mode”
2-Go to the PCI/PnP and make the “PCI IDE BusMaster” is “Disable"

< XP professional /Home /Embedded and Windows 2000 installation note >

1-Please visit technical website to get more information: http://tech.icop.com.tw/

<Enhance CF to run the UD MA2/4>

1-Please select ICOP “ICF Card” to supporting UDMA 2/4 Mode.

<How to b oot up from the Micro SD card>

1-Get into the BIOS setup Utility

2-Go to the Advanced

3-Choose Primary IDE Pin Select: SD card

4-Press “F10” to save configuration changes and exit setup

<Backlight On/Off through GPIO control>
Sample Code:

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

24

#include "stdafx.h"

unsigned char inportb(short addr)

{

unsigned char cValue;

_asm

{

mov dx, addr

in ax, dx

mov cValue, al

}

return cValue;

}

void outpourtb(int addr, unsigned char val)

{

__asm

{

push edx

mov edx, DWORD PTR addr

mov al, BYTE PTR val

out dx, al

pop edx

}

}

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

25

void BackLightON()

{

// Set register 4AH bit1 to 0 to enable GPIOB

outportb(0x3d4, 0x4a);

unsigned c = inport(0x3d5) & 0xfd;

outportb(0x3d4, 0x4a);

outportb(0x3d5, c);

// Set register 48H bit1

outportb(0x3d4, 0x48);

c = inport(0x3d5) | 0x02;

outportb(0x3d4, 0x48);

outportb(0x3d5, c);

}

void BackLightOFF()

{

// Set register 4AH bit1 to 0 to enable GPIOB

outportb(0x3d4, 0x4a);

unsigned c = inport(0x3d5) & 0xfd;

outportb(0x3d4, 0x4a);

outportb(0x3d5, c);

// Clear register 48H bit1

outportb(0x3d4, 0x48);

c = inport(0x3d5) & 0xfd;

outportb(0x3d4, 0x48);

outportb(0x3d5, c);

}

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

26

Note:
1-Wi-Fi module is optional: http://www.icop.com.tw/pddetail.aspx?id=67&pid=4

2 -PDX-089T COM1: support RS232/422/485 and select by BIOS SETUP.
3 -PDX-089T series (CPU Speed: 1GHZ): Support Linux, Windows CE 5.0, CE 6.0,

Windows XP Professional, and Windows Embedded standard (XPE). (Linux ca n

use with Compact Flash card only.)

3.2. BIOS Default setting

If the system cannot be booted after BIOS changes are made, Please follow below procedures in

order to restore the CMOS as default setting.

 Press “End” Key, when the power on

 Press <Del> to enter the AMI BIOS setup
 Press “F9” to Load Optimized Defaults
 Press “F10” to Save configuration changes and exit setup

PDX-089T DM&P Vortex86DX Panel PC with 8.9” WSVGA TFT LCD

27

Warranty

This product is warranted to be in good working order for a period of one year from the date of purchase.
Should this product fail to be in good working order at any time during this period, we will, at our option,
replace or repair it at no additional charge except as set forth in the following terms. This warranty does not
apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for
any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the
use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other
related party. Return authorization must be obtained from the vendor before returned merchandise will be
accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return
Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear

problem description.