ICON Q QBE710 Users manual

Bluetooth Earphone

User Manual

QBE710

Brand name:ICON Q

FCC ID:2ABXDQBE710

Bluetooth headset should be used with the compatible devices
which support Bluetooth wireless technology. This allows you to
make two calls and enjoy the music streaming at any time freely.
Please read this user manual carefully before using the headset,
and also read your device’s user manual regarding the Bluetooth
function, and pay attention to those important safety and
maintenance information.
Please read this user manual carefully before using the headset,
and also read your device’s user manual regarding the Bluetooth
function, and pay attention to those important safety and
maintenance information.
Please keep the headset away from children.

Specifications

Bluetooth Specification

Bluetooth Profiles Supported

Support for Audio Decoding Formats

Transmission Power

Operation Range

Frequency Range

Battery

Charging Voltage

Charging Time

Playing Music Time*

Talk Time *

Standby Time *

Dimensions(mm)

Weight

*The time mentioned as above may vary due to user's operation mode and
device settings.

V4.0

HSP , HFP , A2DP , AVRCP

SBC,MP3,APTX

Class 2

Up to 10 Meters

2.402-2.480GHz

Built-in Rechargeable

3.7V/80mAH(2x40mAH) Lithium Battery

DC4.75-5.25V

About 2 hours

Up to 4.5 hours

Up to 5 hours

Up to 350 hours

L45×W10×H7.5

About 17 g

Structure Sketch

2

6
1

+/

4

8

7

5

(1)Volume Key+(V+)

(2)Speaker

(3)Volume Key- (V-)

(4)Multifunction Button (MFB)

3

/

/

(5)Indicator light

(6)Microphone

(7)Micro USB Charging Socket

(8)NFC Sensor Area

The Headset Status

Status No. Headset Status

Pairing Mode

1

Not Connected

2

Standby Mode

3

Call State

4

5

Charging State

6

Low Voltage State

Note: The two Phones mentioned follows will be called Phone A and B.

Headset’s indicator light status

The headset can be searched, the

indicator light flashes red and blue alternately.

The headset is not connected with the device;

blue light will flash once each 2 seconds.

The headset is connected with the device,

and not any other operations,

blue light will flash once each 5 seconds.

When in a call, the indicator light flashed blue

once each 10 seconds.

The indicator light turns red while being

charged, and will turn blue automatically

after being fully charged.

When the battery’s voltage below 3.3V, the

indicator light flashed red, the speaker
prompt one time every once in a while.

Charging Your Headset

Prior to using the headset for the first time, please fully charge

1.
the battery.
Approximately 2 hours are required to fully charge the headset.

2.
The indicator light turns red while being charged, and will turn

3.
blue automatically after being fully charged.

4.

When the headset is running out of battery, the indicator light
will flash red (the headset will switch off automatically when the
battery is drained). Please charge the headset as above steps
in time to prolong the battery's useful life (Charging indication
will be delayed for a few minutes if the headset has not been
used for a long time or the battery is drained).

Note 1:

Check the charging device is suit to the headset.

Note 2:

Use only the supplied charger to charge the headset, or obey
the validation for this product or the maintenance article and
could be dangerous.

Note 3:

Do not attempt to force open the built-in battery as this could
damage the headset.

Note 4:

If left unused, a fully charged headset will loose its power
automatically. It is recommended to charge the headset each
three months.
Do not leave the headset in a too hot or too cold condition (best

Note 5:

between -10℃ and 50℃) which may affect the headset's
operations although it is fully charged.

Note 6:

Do not dispose of the headset into a fire or water.

Turning On The Headset

In OFF MODE, press and hold MFB for 3 seconds, until you hear
“Power on”, the indicator light turns blue for 1 second, then the
headset will enter into ON MODE.

Turning Off The Headset

In ON MODE (except call state), press and hold MFB for 3
seconds, until you hear “Power off”, the indicator light turns red for
1 second, then the headset will enter into OFF MODE.

Note:

Headset isn’t connected with any devices within 20 minutes,
it will automatically turn off.

Pairing Your Headset With A Bluetooth
Phone

1.

Ensure the headset is off, and the distance between your
headset and phone is within 1 meter to activate the Bluetooth
function on the phone.

2.

Press and hold MFB until the indicator light flashes blue and red
alternately and could hear “pairing” as PAIRING MODE.
Search Bluetooth devices (see the user guide of your phone for

3.
instructions).

4.

Select headset “ QBE710 ” from the found devices list of the
phone.

5.

After waiting for a few seconds, could hear “paired”, then could
hear “your phone is connected”.(If the pairing cannot be
completed within 5 minutes after the PAIRING MODE has been
activated, the headset will enter into the STANDBY MODE.
Please repeat above steps to do the pairing again).

6.

Ensure the distance between your headset and phone is within
effective distance, you can use the headset freely.

7.

When the headset is off, it will connect the paired phone
automatically if you turn on the headset again within operation
range.

Note: When the mobile phone Bluetooth version below 2.1, it
need to enter pairing code “0000”;
When the mobile phone Bluetooth version 2.1 or exceed 2.1, it
don’t need to enter the pairing code.

Q

Answering A Call

When a call is coming, you can answer it with the ways as follows:
Method 1: Press MFB once.

Method 2: Answer the call with your phone.

Ending A Call

You can end the call you are answering with the ways as follows:
Method 1: Press MFB once.

Method 2: End the call with your phone.

Rejecting A Call

Press and hold MFB for 2 seconds to reject the call.

Voice Dialing

In PAIRED MODE, press and hold volume V- for 2 seconds, and
say the voice tag as soon as you hear the short beep. (Ensure your
phone supports voice dialing function, and you have recorded the
voice tag into your phone. See the user guide of your phone for
instructions.)

Two-call Handling

When you are answering one call, there is another call coming:

Shortly press headset MFB once to hold on the current call and

1.
answer another call.

2.

Shortly press the headset once to transfer the call from one to
another.
Press and hold the headset MFB for 2 seconds, the speaker

3.
sound “du” ; you can end the current talking call and answer the
retained call.

Note:

All the above operations have to respect the precondition
that Phone supports Bluetooth hands free profile V1.5
and Phones are running under call holding function from
telecom.

Adjusting The Volume

In call or playing music state, shortly press V+ or V- once to adjust
the volume. When the volume up to maximum or minimum, you
could hear “da” voice prompt.

Mute

During a call, press and hold “V+” for 3 seconds, you could hear
“dudu” voice prompt, the headset will enter in to MUTE MODE. In
MUTE MODE, the speaker will sound “dudu” twice each 10
seconds, press and hold “V+” for 3 seconds again, you could hear
“dudu” voice prompt, then could cancel the MUTE MODE.

Transferring The Call

During a call, press and hold “V-” for 2 seconds, you could hear “du”
voice prompt, the call transfer to the mobile phone. Press and hold
“V-” for 2 seconds again, you could hear “du” voice prompt, the call
transfer to the headset.

Last Number Redialing

In Single link mode, press MFB twice, the headset will

·

automatically redial phone last dial out the number.
In Two link mode, press MFB twice, the headset will redial the

·

phone’s last dial out the number, this phone is connected firstly.
Press and hold “V+” for 2 seconds, you could hear “du” voice
prompt, then the headset will redial the phone last dial out the
number, this phone is connected secondly. (Connecting the
phone's sequence shall prevail)

Forward/Backward

Press and hold “V-” or “V+” for 2 seconds to forward the next song
or to backward the last song.

Playing/Pause

In playing music state, shortly press MFB once, you could hear “du”
voice prompt, it could realize playing and pause.

Delete Pairing Record On The Headset

In standby mode, press and hold “V+” and “V-”, until the red and
blue light flashed twice at the same time, you could hear “dudu”
voice prompt, and then press and hold MFB for 3 seconds, until the
headset turn off, the pairing record on the headset will be deleted,
when all the pairing record is deleted, after the headset turn on, it
couldn’t connected automatically, could enter into pairing mode
directly.

Headset Resetting

In any state, as long as the headset is charging, it will be reset.

Two-link Function

Note: The two Phones mentioned follows will be called Phone A and
B.

Two-link Function

This function means “ QBE710 ” Bluetooth headset is connected
with 2 Phones of Bluetooth function at the same time.
When the Phone A & Phone B are neither paired, the two link
operation is as below:
a)Pairing Phone A: In off mode, press and hold MFB until indicator
light flashes red and blue alternately, use phone A search the
bluetooth device “ ”, select “ ” to pair the
headset with phone A, and the headset will enter into standby
mode.
b) Turn off the Bluetooth function in Phone A, the headset will into
no connected status.
c)Pairing Phone B: In off mode, press and hold MFB until indicator
light flashes red and blue alternately, use phone B search the
bluetooth device “ ”,select “ ” to pair the headset
with phone B, and the headset will enter into standby mode.
d). Connecting the Phone A&B at the same time:
Method 1: Activate the Bluetooth function of Phone A, search the
Bluetooth device “ ” with Phone A, and connect the
“BS052RU” with this phone, here 2 Phones are connected with the
headset.
Method 2: Activate the Bluetooth function of Phone A&B, and
re-turn on the on mode headset. The headset will automatically
connect with the last connecting phone (phone A or B), if you want
to connect with the other phone, you need to connect it by hand.

Note 1:

For the differences of Phones, it doesn’t guarantee
compatibility of all functions on every Bluetooth enabled
device.

Note 2:

Redial the last phone number after connecting two
Phones, the device will choose number of the Phone
which is connected first(not the one pairing first) to call.
The other phone does not respond for calling.

Note 3:

For voice dialing after connecting two Phones, the
device will choose number of the Phone which is
connected first(not the one pairing first) to call. The other
phone does not respond for calling.

Note 4:

When the mobile phone Bluetooth version below 2.1, it
need to enter pairing code “0000”; when the mobile
phone Bluetooth version 2.1 or exceed 2.1, it don’t need
to enter the pairing code.

Q

Q

QBE710

Q

QBE710

QBE710

Q

Q

Q

QBE710

QBE710

Switching Between Two Calls

The headset is connected with two phones, and gets through

·

a call from phone A, there is a call from phone B, you could
press the MFB once to answer the call from Phone B, the call
from phone A is under the status of waiting. Re-press the MFB
once, you could switch the two calls each other.
Press and hold MFB for 2 seconds, you could hear “du” voice

·

prompt, to end the call you are answering, and then can
transfer to another phone to answer the call.

Disconnecting

To disconnect the paired headset from your phone, please turn off
the headset or disconnect the headset from the Bluetooth menu of
your phone. When disconnecting, could hear “Your phone is
disconnected”.

Automatic Reconnect

When the headset and the mobile phone have been paired, don’t
need to do connecting, the headset will automatically connect with
the mobile phone (firstly ensure the mobile phone’s Bluetooth
function have open, and the distance between your headset and
phone is within effective distance).
Situation 1: The headset in OFF MODE, after open the headset by
hand, the headset will connect with the mobile phone according to
the pairing list one by one.
Situation 2: The headset in STANDBY MODE, the distance
between your headset and phone exceed effective distance, the
headset will disconnect with the mobile phone automatically, the
speaker sound voice prompt, when the headset return to effective
distance within 2 minutes, you could shortly press MFB once, the
headset will automatically connect with the mobile phone (Ensure
the headset in ON MODE).

NFC Function Operation

Before using this function, please make sure your mobile NFC is
open and has activated the phone's screen, and confirm the
mobile phone's NFC sensor area.

1. Using NFC turn on and pairing
The headset in OFF MODE, take your mobile phone and
headset's NFC sensor area close each other, in this time the
mobile phone could identify the headset, mobile phone pop-up
dialog, continue to near until the indicator light flashes red and
blue alternately, and then according to the need to select "yes" or
"no". If need a password, please enter "0000", after the successful
pairing, the headset will automatically connect with the phone.
(Mobile phone models different, then the operating and prompt will
be different.)

2. Using NFC to turn off
The headset in STANDBY MODE, take your mobile phone and
headset's NFC sensor area close each other, continue to near for
3 seconds, the headset's speaker will sound voice prompt,
indicator light turn red for 1 second and then put out, then the
headset enter into OFF MODE.

Maintenance

1.

Do not use abrasive cleaning solvents to clean the headset.
Do not allow the headset to touch with any sharp objects as this

2.
will cause scratching and damage.

3.

Please keep headset away from high-temperature, humidity and
dust.

Additional Statements

·

The headset is compliant with the specified bluetooth
version. It does not guarantee compatibility of all functions
on every bluetooth enabled device. Please check your
device’s user manual for compatibility and functionality.

·

The headset will beep when operates successfully but
this may be too low to hear.

·

The above operations may vary due to different devices.
Manufacturer reserves the right of final explanation of all

·

the above statements.

This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user’s authority to
operate the equipment.