1. Read this manual thoroughly before using this unit.
2. Keep this manual for future reference.
3. Take notice of and comply with all warnings included in the user's manual or indicated on the
appliance.
4. Follow all instructions included in this manual.
5. Do not expose this unit to rain or moisture. Avoid having water or other liquids spilled on this
unit.
6. When cleaning the cabinet or other parts of this appliance, use only a dry or slightly damp soft
cloth.
7. Do not block any ventilation openings or interfere with the proper ventilation of this unit. Install
in accordance with the manufacturer's instructions.
8. Do not use or store near any heat sources such as radiators, heat registers, stoves, or other heat producing appliances.
9. Do not interfere with the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding-type plug has two blades and a third
grounding prong. These are designated for your safety. If the provided plug does not fit into your
outlet, consult an electrician.
10. Protect the power cord from being walked on or otherwise damaged by items placed on or against them. Particular attention should be given to the plugs, receptacles, and the point where
the cord exits the appliance.
11. To avoid the risk of electrical shock, do not touch any exposed wiring while the unit is in
operation.
12. Only use attachments/accessories specified by the manufacturer.
13. Unplug this unit and all connected electrical equipment during lightning storms or when left
unused a long period of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the appliance has
been damaged in any way or fails to operate normally.
WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture
Thank you for purchasing the ICON ProAudio CubePro digital audio Interface. We
sincerely trust this product will provide years of satisfactory service, but if anything is
not to your complete satisfaction, we will endeavor to make things right.
In these pages, you'll nd a detailed description of the features of the CubePro digital
audio interface, as well as a guided tour through its front and rear panels, step-by-
step instructions for their setup and use, and full specications.
Please register the product on our website at the below link www. iconproaudio.com/registration:
Please follow the step by step procedures. Start by inputing the device’s serial
number as well as your personal information, etc. By registering your product online,
you will be entitled to service and after-sales support at our Help Center by visiting
our website at www.iconproaudio.com. Also, all the registered products under your
account will be listed on your personal product page where you will nd updated
information such as rmware/driver upgrades, software bundles, user manual
downloads, etc. for your device.
As with most electronic devices, we strongly recommend you retain the original
packaging. In the unlikely event the product must be returned for servicing, the
original packaging (or reasonable equivalent) is required.
With proper care and adequate air circulation, your CubePro digital audio interface
will operate without any trouble for many years. We recommend that you record your
serial number in the space provided below for future reference.
What’s in the package?
● CubePro USB Recording Interface
● Quick Start Guide x 1
● USB 2.0 cable x 1
4
Page 5
Register your ICON ProAudio product to your
personal account
1. Check serial number of your device
Please go to http:// iconproaudio.com/registration or scan the QR code
below.
Input your device’s serial number and the other information on the screen. Click
“Submit”.
A message will pop up showing your device information such as model name
and its serial number - Click “Register this device to my account” or if you see
any other message, please contact our after-sales service team
2. Log in to your personal account page for existing user or
sign up for new user
Existing user: Please log into your personal user page by inputing your
user name and password.
New user: Please click “Sign Up” and ll in all the information.
3. Download all useful materials
All your registered devices under your account will show on the page. Each
product will be listed along with all its available les such as drivers, rmware,
user manual in different languages and bundled software etc. for download.
Please make sure you have download the necessary les such as driver before
you begin device installation.
5
Page 6
Features
The ICON CubePro USB recording interface provides an audio input and output
module with USB connectivity. Main features include:
● 24-Bit 192KHz 4-In/4-Out USB Recording Interface
● High dynamic range:
DAC: Dynamic Range: 114dB
ADC: Dynamic Range: 114dB
● 4x4 analog I/O full duplex recording and playback
● 4 analog inputs and 4 analog outputs on 1/4” TRS jacks
● Master volume control on the front panel
● 1 headphone output with assignable source and individual volume control
● Flexible channel routing via the software control panel
● ICON innovative ProDriveⅢ™ plug-ins hosting rack is provided
● Different plug-ins are provided
● USB2.0 High Speed equipped and USB bus-powered
● Supports DirectSound, WDM and ASIO2.0
● Compatible with Mac OS (Intel-Mac), iOS 9 or above and Windows 7, 8 & 10
(32-bit/64-bit)
● Full duplex, simultaneous record/playback
● +5VDC power supply connector is equipped for external power supply when using
with iOS
● Rugged aluminum construction
6
Page 7
Front Panel
1234
1. Line Inputs 1-4
These are unbalanced analog inputs on standard 1/4" TS connectors at-10dB line level.
2. Master level control
This potentiometer controls the master output level of the analog outputs.
3. Headphone level control
This potentiometer controls the output level of the headphone output.
4. Headphone output
This output jack accepts a standard 1/4″ stereo TRS headphone connector.
7
Page 8
Rear Panel
231
1. USB 2.0 Connector
Connect it with the provided USB cable to your Mac/PC/iOS device camera kit’s
USB connector. Your Mac/PC must have a USB2.0 connector in order to run the
full speed of CubePro .
2. Line outputs 1-4
These are unbalanced analog outputs on standard 1/4″ TS connectors at +6dBU
line level.
3. Power supply connector
CubePro is USB bus powered. If your computer does not supply sufcient
power, connect an ICON +5VDC power supply adapter to this jack or use a
standard phone charger/power adapter with the correct USB cable.
(Note: You can get the power adapter from ICON Distributors/dealers near you.)
8
Page 9
Mac driver installation
Ⅲ
CubePro is a class compliance device. Thus there is no driver installation
needed for Mac. Also, it is fully supporting iOS devices by connecting to a
camera kit.
Please follow the step-by-step procedures below to install your CubePro USB
recording interface.
1. Turn on your Mac
(Note: Do not connect the CubePro digital audio interface to your Mac yet.)
2. Class compliance device
CubePro is class compliance on Mac OSX, no driver installation is needed.
3. Copy the software control panel shortcut logo to your
desktop
Open the previous “Mac” folder. Copy the “ProDriveⅢ” software panel shortcut
logo and paste it to your desktop.
Mac
Ⅲ
Ⅲ
Ⅲ
Diagram 1
4. Launch the software control
panel
Click the CubePro ’s software control
panel shortcut logo you have just
copied to your desktop to launch the
software control panel.
Ⅲ
Ⅲ
Diagram 2
9
Page 10
5. Connect your CubePro
digital audio interface
Now connect the CubePro digital
audio interface to your Mac's USB
port.
Note: CubePro audio interface only
support USB2.0. Your Mac must have
a USB2.0 port.
Diagram 3
USB
intel
CapsLook
Shift
Ctrl
F1
Esc
~
!
`
1
Tab
Q
A
Z
F5
F3
F2
F6
F4
%
··
#
¥
2
3
6
4
5
T
W
E
R
G
S
F
D
X
C
V
B
AltAltGr
pause
Prtsc
F10
F7
F8
F11
F12
F9
Lns
Del
Break
sysrq
#
#
*
)
Home
—
+
)
*
Backspace
-
=
7
78
9
0
{
}
|
P
O
Y
U
I
Pgup
[
]
|
PgDN
:
L
H
K
J
Enter
;
?
M
<
>
N
End
Shift
Ctrl
$
6. Audio MIDI setup
Open the “Audio MIDI setup”
window and check if the CubePro
device has setup properly as
shown below in diagram 4.
CubePro (Bit Accurate)
CubePro (Core Audio)
Diagram 4
CubePro (Core Audio)
CubePro: Output
10
Page 11
Mixer control panel
Ⅲ
The mixers work like a matrix mixer. Activate and adjust the corresponding input or output
channel level. They are very useful and make your inputs and outputs very exible. You may
route any of your input(s) to any output(s).
1
9
3
2
7
Diagram 5
1. HW Input 1/2 level metering
Showing the hardware 1/2 input level. (HW In 1/2).
2. HW Output 1/2 level metering
Showing the hardware 1/2 output level.(HW Out 1/2).
3. HW Input 3/4 level metering
Showing the hardware 3/4 input level. (HW In 3/4).
4. HW Output 3/4 level metering
Showing the hardware 3/4 output level.(HW Out 3/4).
5. Link switch
Switch to adjust both channels level simultaneously.
6. Mute switch
Switch to mute the corresponding channel.
7. “0dB” switch
Switch to instantly adjust the corresponding channel to “0dB” level.
8
4
5
6
8. Gain control fader
Slide to adjust the gain level for the corresponding channel.
9. Inputs & Outputs Matrix switches
Switch to turn On/Off the corresponding input channel route to the corresponding
output channel. The matrix is very useful and makes your inputs and outputs very
exible. You may route any of your input(s) to any output(s)
.
11
Page 12
Windows driver installation
Please follow the step-by-step procedures below to install your CubePro USB
recording interface and its driver.
1. Turn on your computer
Note: Do not connect the CubePro digital audio interface to your computer yet.
2. Download the Windows driver from your “Personal User
Page at www.iconproaudio.com”
After you downloaded the driver le, please click it to start the installation
process
Cube Pro
HQ0H3
3. Installation Wizard appears
Choose "Next" when you see the Welcome
Screen shown in Diagram 7.
4. License Agreement
Click “I Agree” to proceed.
Diagram 6
Diagram 7
12
Diagram 8
Page 13
Ⅲ
Ⅲ
5. Select components for installation
Check mark the components that you would
like to install. We strongly recommend you to
select all components.
Ⅲ
Cube Pro Device Drivers
Diagram 9
6. Preparing installation les
The installation process started, the process
may take some time depending on your
computer performance, please be patient
and wait for the process to nish.
7. Click “Install” to proceed.
Note: Same message will appear three
times as there are three different drivers
installation.
Diagram 10
Diagram 11
Diagram 12
Ⅲ
Icon_
Cube Pro
_2.9.86.50.exe
Diagram 13
13
Page 14
8. Setup completed
A window as shown in Diagram 14
should appear. Choose "Finish”.
Diagram 14
9. Launch the software
control panel
You may click the ICON ProAudio
logo on the system tray to launch
the software control panel (Page
16).
10. Connect your CubePro
digital audio interface
Now connect the CubePro
digital audio interface to your
computer's USB port.
Cube Pro
Diagram 15
Diagram 16
Ⅲ
F5
F3
pause
Prtsc
F10
F7
F8
F11
F12
F9
F1
Esc
F2
F6
F4
Lns
Del
Break
USB
~
!
`
1
Tab
Q
A
CapsLook
Z
Shift
Ctrl
intel
%
··
#
¥
2
3
4
5
T
W
E
R
G
S
F
D
X
C
V
B
AltAltGr
sysrq
#
#
*
)
Home
—
+
)
*
Backspace
-
=
6
7
78
9
0
{
}
|
P
O
Y
U
I
Pgup
[
]
|
PgDN
:
L
H
K
J
Enter
;
?
M
<
>
N
End
Shift
Ctrl
$
14
Page 15
ProDrive
Diagram 17
Ⅲ
Diagram 18
To make the CubePro very versatile and powerful, we have developed a new
technology ProDriveⅢ - it is our innovative rack, plug-in host, and virtual signal
router. Run it in standalone mode or with your favorite DAW. Pull up your guitar
modeling and play, or plug in your midi controller and control your favorite virtual
instruments without running through your digital audio workstation.
15
Page 16
Mixer control panel
On the mixer control panel, there are four different main types of ASIO channels that
you can manipulate.
1. CubePro Hardware channels (HW In 1/2, 3/4 & HW Out 1/2, 3/4)
These are the hardware input and output channels on CubePro .
2. CubePro Virtual channels (VC In 1/2, 3/4 and 5/6), (VC Out 1/2,
3/4 and 5/6)
These are the input and output virtual channels that related to the WDM. For example: WDM Out 1/2 linked to VC In1/2VC Out1/2 linked to WDM In1/2
3. CubePro Loopback channels (LB 1/2, 3/4 and 5/6)
These are the ASIO loop-back channels.
1
3
5
6
7
11
18
12
13
2
16
13
121110984
Diagram 19
By activating different cross points, you may route the corresponding signal to your
desired channels.
1. HW Input 1/2 level metering
Showing the hardware 1/2 input level (HW In 1/2).
2. HW Output 1/2 level metering
Showing the hardware 1/2 output level (HW Out 1/2).
16
17
14
15
Page 17
3. HW Input 3/4 level metering
Showing the hardware 3/4 input level (HW In 3/4).
4. HW Output 3/4 level metering
Showing the hardware 3/4 output level (HW Out 3/4).
5. VC In 1/2 (Virtual) input level metering
Showing the WDM 1/2 output level (VC In 1/2).
6. VC In 3/4 (Virtual) input level metering
Showing the WDM 3/4 output level (VC In 3/4).
7. VC In 5/6 (Virtual) input level metering
Showing the WDM 5/6 output level (VC In 5/6).
8. VC Out 1/2 (Virtual) output level metering
Showing the ASIO 1/2 VC output level (VC Out 1/2).
9. VC Out 3/4 (Virtual) output level metering
Showing the ASIO 3/4 VC output level (VC Out 3/4).
10. VC Out 5/6 (Virtual) output level metering
Showing the ASIO 5/6 VC output level (VC Out 5/6).
11. Loopback 1/2
Showing the ASIO loop-back 1/2 channel’s level metering.
12. Loopback 3/4
Showing the ASIO loop-back 3/4 channel’s level metering.
13. Loopback 5/6
Showing the ASIO loop-back 5/6 channel’s level metering.
14. Link switch
Switch to adjust both channels level simultaneously.
15. Mute switch
Switch to mute the corresponding channel.
16. “0dB” switch
Switch to instantly adjust the corresponding channel to “0dB” level.
17. Gain control fader
Slide to adjust the gain level for the corresponding channel.
18. Inputs & Outputs Matrix switches
Switch to turn On/Off the corresponding input channel route to the corresponding
output channel. The matrix is very useful and makes your inputs and outputs
very exible. You may route any of your input(s) to any output(s).
17
Page 18
Settings (Sample rate and latency settings)
Click the “Setting” button to launch the settings window.
Diagram 20
Sample rate setting
Select your desired sampling rate from 44.1KHz to 192KHz on the pull down
window shown in Diagram 21.
18
Diagram 21
Page 19
Latency settings
There are six standard latency settings to select. If you would like to customize
your own latency value, select custom.
● Safe (maximum latency)
● Extra Large
● Normal
● Small
● Very Small
● Minimum (minimum latency)
● Custom
Diagram 22
19
Page 20
There are three different settings you can adjust to customize your own latency
settings: These values include:
1. ASIO buffer Size
You may adjust the value ranging from 32/64/128/256/512/1024/2048 and 4096.
Diagram 23
2. Streaming buffer Size
Adjustable settings: Minimum/Low/Normal/High and Maximum.
20
Diagram 24
Page 21
3. Streaming buffer volume
Adjustable values: 2/3 and 4.
Diagram 25
Diagram 26
(Note: If a warning message appears on the “Latency Status” windows, please
adjust a larger latency setting.)
(Note: If a clicking sound occurs, you should change to a larger buffer size
for the settings. If the largest buffer size has been selected and there is still a
clicking sound. It means your computer performance is not able to handle the
task. (It is not caused by CubePro digital audio interface.)
21
Page 22
ProDrive
With the ProDriveⅢ Rack, you can use any of your plug-ins with your DAW. Or you
may use your device as a standalone plug-ins effector without the need to run a
DAW.
hosting rack
Ⅲ
22
Page 23
Hardware Connections
Mac
Connect the CubePro digital audio interface outputs to your amplier, powered
monitors or surround system. Two-channel stereo operation, the default outputs are
channels 1 and 2.
If you are monitoring through headphones, connect your headphones to the device’s
headphone output.
Connect your line level analog sources to the device's analog inputs.
Power Pack
Mixer
or
Line Level Signal
Mac / PC
1
2
23
Page 24
Specications
Line Inputs 1-4(Unbanced):
Frequency Response: .................................... 22Hz to 22kHz (+/-0.1dB)
Load Impedance: ............................................ 32 to 600 Ohms
24
Page 25
Services
If your CubePro needs servicing, follow these instructions.
Check our online Help Center at http://support.iconproaudio.com/hc/en-us, for
information, knowledge, and downloads such as:
1. FAQ
2. Download
3. Learn More
4. Forum
Very often you will nd solutions on these pages. If you don’t nd a solution, create
a support ticket at our online Help Center at the link below, and our technical support
team will assist you as soon as we can.
Navigate to http://support.iconproaudio.com/hc/en-us and then sign in to submit
a ticket.
As soon as you have submitted an inquiry ticket, our support team will assist you to
resolve the problem with your ICON ProAudio device as soon as possible.
To send defective products for service:
1. Ensure the problem is not related to operation error or external system devices.
2. Keep this owner's manual. We don't need it to repair the unit.
3. Pack the unit in its original packaging including end card and box. This is very
important. If you have lost the packaging, please make sure you have packed
the unit properly. ICON is not responsible for any damage that occurs due to
non-factory packing.
4. Ship to the ICON tech support center or the local return authorization. See our
service centers and distributor service points at the link below:
If you are located in US Send the product to:
North AmericaMixware, LLC – U.S. Distributor11070 Fleetwood Street – Unit F.Sun Valley, CA 91352; USATel.: (818) 578 4030