INSTRUCTION MANUAL
VHF MOBILE TRANSCEIVER
iF5061
iF5063
UHF MOBILE TRANSCEIVER
iF6061
iF6063
IMPORTANT
PRECAUTIONS
READ ALL INSTRUCTIONS carefully and com-
pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This
instruction manual contains important operating instructions
for the IC-F5061, IC-F5063, IC-F6061 and IC-F6063
VHF/UHF MOBILE TRANSCEIVERS.
RWARNING! NEVER connect the transceiver to an
AC outlet. This may pose a fire hazard or result in an electric
shock.
NEVER connect the transceiver to a power source of more
than 16 V DC such as a 24 V battery. This connection will ruin
the transceiver.
NEVER cut the DC power cable between the DC plug and
EXPLICIT DEFINITIONS
WORD DEFINITION
RWARNING
CAUTION
NOTE
See the operating guide for details of BIIS, MDC and LTR
system operations. Ask your dealer for details.
Icom, Icom Inc. and the logo are registered trademarks of Icom
Incorporated (Japan) in the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
LTR is a registered trademark of the E.F.Johnson Company.
All other products or brands are registered trademarks or trademarks of their
respective holders.
i
Personal injury, fire hazard or electric shock
may occur.
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
fuse holder. If an incorrect connection is made after cutting,
the transceiver might be damaged.
NEVER place the transceiver where normal operation of
the vehicle may be hindered or where it could cause bodily
injury.
NEVER allow children to touch the transceiver.
NEVER expose the transceiver to rain, snow or any liquids.
USE the specified microphone only. Other microphones
have different pin assignments and may damage the trans-
®
ceiver.
DO NOT use or place the transceiver in areas with tem-
peratures below –30°C (–22°F) or above +60°C (+140°F), or
in areas subject to direct sunlight, such as the dashboard.
TABLE OF CONTENTS
AVOID operating the transceiver without running the vehi-
cle’s engine. The vehicle’s battery will quickly run out if the
transceiver transmits while the vehicle’s engine OFF.
AVOID placing the transceiver in excessively dusty envi-
ronments.
AVOID placing the transceiver against walls. Otherwise
heat dissipation will be obstructed.
AVOID the use of chemical agents such as benzine or
alcohol when cleaning, as they damage the transceiver surfaces.
BE CAREFUL! The transceiver will become hot when
operating continuously for long periods.
For U.S.A. only
CAUTION: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate
this transceiver under FCC regulations.
IMPORTANT .................................................................................... i
EXPLICIT DEFINITIONS ................................................................. i
PRECAUTIONS ............................................................................... i
TABLE OF CONTENTS .................................................................. ii
1 PANEL DESCRIPTION ........................................................... 1–7
■ Front panel ............................................................................... 1
■ Function display ....................................................................... 2
■ Programmable function keys ................................................... 3
2 BASIC OPERATION ............................................................. 8–14
■ Turning power ON .................................................................... 8
■ Channel selection .................................................................... 8
■ Call procedure .......................................................................... 9
■ Receiving and transmitting ....................................................... 9
D Transmitting notes ............................................................... 10
D TX code channel selection .................................................. 10
D TX code number edit............................................................ 11
D Talkgroup ID code selection ................................................ 12
D TX Status message selection .............................................. 12
D DTMF transmission ............................................................. 13
■ Scrambler function ................................................................. 13
■ User set mode ........................................................................ 14
3 CONNECTION AND MAINTENANCE ................................ 15–17
■ Rear panel connection ........................................................... 15
■ Supplied Accessories ............................................................. 16
■ Mounting the transceiver......................................................... 16
■ Antenna ................................................................................... 17
■ Fuse replacement .................................................................. 17
■ Cleaning ................................................................................. 17
■ Options ................................................................................... 17
4 SAFETY TRAINING INFORMATION ........................................ 18
ii
1
Icom Inc.
qe
y
SpeakerFunction display (p. 2)
w r
t
PANEL DESCRIPTION
■ Front panel
q AF VOLUME CONTROL KNOB [VOL]
Rotate the knob to adjust the audio output level.
• Minimum audio level is pre-programmed.
w LED INDICATOR
➥ Lights red while transmitting a signal.
➥ Lights green while receiving a signal.
e UP/DOWN KEYS [CH Up]/[CH Down]
Push to select an operating channel, etc.
*The desired function can be assigned by your dealer. (p. 3)
r POWER SWITCH [ ]
Push to turn the power ON and OFF.
• Automatic scan start, Password prompt and Set mode access
are available at power ON.
t DEALER-PROGRAMMABLE KEYS
Desired functions can be programmed independently by
your dealer. (p. 3)
1
y MICROPHONE CONNECTOR
Connect the supplied or optional microphone.
NEVER connect non-specified microphones. The pin
assignments may be different and the transceiver may
be damaged.
DD
MICROPHONE
The supplied microphone has a PTT switch and a hanger hook.
• The following functions are available when the microphone is on or
off hook (depending on the setting):
- Automatic scan start when on hook.
- Scan is cancelled when off hook.
- Scan is paused when off hook.
- Automatic priority channel selection is available when off hook.
- Sets to ‘Inaudible’ condition (mute condition) when on hook.
- Sets to ‘Audible’ condition (unmute condition) when off hook.
PANEL DESCRIPTION
Weak ⇐ Receive Signal level ⇒ Strong
Icom Inc.
qw ertyuio
!0
!1
1
■ Function display
q SIGNAL STRENGTH INDICATOR
Indicates relative signal strength level as below.
w LOW POWER INDICATOR
Appears when low output power is selected.
e AUDIBLE INDICATOR
➥ Appears when the channel is in the ‘audible’ (unmute)
condition.
➥ Appears when the specified 2/5-tone/BIIS*
code is received.
r COMPANDER INDICATOR
Appears when the compander function is activated.
t SCRAMBLER INDICATOR
Appears when the voice scrambler function is activated.
1
/MDC*
y BELL INDICATOR
Appears/blinks when the specific 2/5-tone/BIIS*
code is received, according to the pre-programming.
u CALL CODE MEMORY INDICATOR
➥ Appears when the call code memory is selected.
➥ Appears when a phone call is received.*
i SCROLL INDICATOR
Appears when the received SDM includes more than 12
characters.*
o SDM INDICATOR
Appears when an SDM is received, or a transmit SDM is
selected.*
!0 ALPHANUMERIC DISPLAY
➥ Displays an operating channel number, channel name,
Set mode contents, DTMF code, etc.
➥ The indication mode can be selected from 1 line or 2
lines. Ask your dealer for details.
• In this instruction manual, the LCD illustration is described
using the 2 lines indication mode.
!1 ACTIVATED KEY INDICATOR
2
Appears above the key assigned as [Scan A Start/Stop],
[Scan B Start/Stop], [Scan Add/Del(Tag)], [Lock], [Talk
Around], [Surveillance], [Talkgroup]*
during that key is activated.
*1BIIS operation only *2MDC operation only
*3LTR®operation only *4Digital operation only
See the operating guide for details of BIIS, MDC and LTR
system operations. Ask your dealer for details.
1
1
1
/MDC*
3
4
and [Digital]*1keys
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
®
2
PANEL DESCRIPTION
1
■ Programmable function keys
The following functions can be assigned to [UP], [DOWN],
[P0], [P1], [P2], [P3] and [P4] programmable function keys.
Consult your Icom dealer or system operator for details concerning your transceivers programming.
If the programmable function names are bracketed in the following explanations, the specific key is used to activate the
function depends on the programming.
CH UP AND DOWN KEYS
➥ Push to select an operating channel.
➥ Push to select a transmit code channel after pushing [TX
Code CH Select].
➥ Push to select a DTMF channel after pushing [DTMF
Autodial].
➥ Push to select a scan group after pushing and holding
[Scan A Start/Stop]/[Scan B Start/Stop] for 1 sec.
ZONE KEY
Push this key, then select the desired zone using [CH Up]/
[CH Down].
What is “zone”?—The desired channels are assigned
into a zone according to the intended use for grouping.
For example, ‘Staff A’ and ‘Staff B’ are assigned into a
“Business” zone, and ‘John’ and ‘Cindy’ are assigned into a
“Private” zone.
3
SCAN A START/STOP KEY
➥ This key’s operation depends on the Power ON Scan setting.
When the power ON scan function is turned OFF;
Push to start and cancel scanning operation.
When the power ON scan function is turned ON;
Push to pause scanning, then resumes scanning after a
specified time period has passed.
➥ Push and hold this key for 1 sec. to indicate the scan group,
then select the desired group using [CH Up]/[CH Down].
SCAN B START/STOP KEY
➥ Push to start and cancel scanning operation. Scan
resumes after a specified time period has passed when
scan is cancelled except for this key.
➥ Push and hold this key for 1 sec. to indicate the scan group,
then select the desired group using [CH Up]/[CH Down].
SCAN ADD/DEL (TAG) KEY
➥ Push to add or delete the selected channel to/from the
scan group.
1. Push to indicate the scan group, then push [CH Up] or [CH
Down] to select the desired group.
2. Push to add or delete the channel to/from the selected scan
group.
3. Push and hold for 1 sec. to exit the scan group selection mode.
➥ Push this key while scan is paused (a signal is detected)
on a channel (except for priority channel,) the channel is
cleared from the scan group.
Depending on the setting, the cleared channel is added
to the scan group again after the scan is cancelled.
PANEL DESCRIPTION
1
PRIO A/B KEYS
➥ Push to select Priority A or Priority B channel.
➥ Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] to set
the operating channel as the Priority A or Priority B channel.
MR-CH 1/2/3/4 KEYS
Push to select the memory channel 1 to 4 directly.
MONI (AUDI) KEY
➥ Mute and release the CTCSS (DTCS) or 2-tone squelch
mute. Open any squelch/deactivate any mute while pushing and holding this key. (LMR operation only)
➥ Activates one of (or two of) the following functions on each
channel independently: (PMR or BIIS PMR operation only)
• Push and hold to un-mute the channel (audio is emitted;
‘Audible’ condition).
• Push to mute the channel (sets to ‘Inaudible’ only).
• Push to un-mute the channel (sets to ‘Audible’ only).
• Push after the communication is finished to send a ‘reset code’.
(BIIS PMR operation only)
NOTE: The un-mute condition (‘Audible’ condition) may
automatically return to the mute condition (‘Inaudible’ condition) after a specified period depending on programming.
PUBLIC ADDRESS KEY
Push to activate the Public Address (PA) function for voice
amplification. When the PA function is activated, the audio
output can be controlled from the transceiver separately with
the [VOL] control knob.
• This function is available when the external unit, such as a audio
amplifier, speaker, etc. is additionally connected.
•Push this key, then speak into the microphone while pushing and
holding [PTT].
•[CH Up]/[CH Down] also allow you to set the audio output level.
RX SPEAKER KEY
The received audio can be heard via the external speaker
when this key is pushed.
• This function is available when the external speaker is additionally
connected.
•This function is useful when you are out of the vehicle.
•The audio output level is linked to the transceiver’s volume control.
LIGHT KEY
Push to turn the transceiver’s backlight ON for about 5 sec.
when the backlight function is turned OFF in user set mode.
LOCK KEY
Push and hold to electronically lock all programmable keys
except the following:
[Moni(Audi)], [Light], [Lock], [Call] (incl. Call A and Call B),
[Emergency Single]/[Emergency Repeat] (incl. Silent), [Surveillance]
and [OPT 1/2/3].
1
4
PANEL DESCRIPTION
1
HIGH/LOW KEY
Push to select the transmit output power temporarily or per-
SCRAMBLER FUNCTION
Push to toggle the voice scrambler function ON and OFF.
manently, depending on the pre-setting.
•Ask your dealer for the output power level for each selection.
CALL KEYS
Push to transmit a 2/5-tone/BIIS ID code.
C.TONE CH ENT KEY
Push to select the continuous tone channel using [CH Up]/[CH
Down] to change the tone frequency/code setting after pushing this key. The selected channel remains set as the continuous tone channel until another channel is designated as such.
TALK AROUND KEY
Push to turn the talk around function ON and OFF.
•The talk around function equalizes the transmit frequency to the
receive frequency for transceiver-to-transceiver communication.
•Call transmission is necessary before calling another station
depending on your signalling system.
•[Call A] and/or [Call B] may be available when your system employs
selective ‘Individual/Group’ calls. Ask your dealer which call is
assigned to each key.
EMERGENCY KEYS
➥ Push and hold to transmit an emergency call.
➥ When [Emergency Single (Silent)] or [Emergency Repeat
(Silent)] is pushed, an emergency call is transmitted with
no beep emission and LCD indication change.
WIDE/NARROW KEY
Push to toggle the IF bandwidth between wide and narrow.
• The wide passband width can be selected from 25.0 or 20.0 kHz
using the CS-F5060
tion only) Ask your dealer for details.
CLONING SOFTWARE
. (PMR or BIIS PMR opera-
• If you want to cancel the emergency call, push (or push and
hold) the key again before transmitting the call.
• The emergency call is transmitted one time only or repeatedly
until receiving a control code depending on the pre-setting.
SURVEILLANCE KEY
DTMF AUTODIAL KEY
Push to enter the DTMF channel selection mode. Then select
the desired DTMF channel using [CH Up]/[CH Down].
After selecting the DTMF channel, push again to transmit the
Push to turn the surveillance function ON or OFF.
When this function is turned ON, the beep is not emitted and
the LCD backlight and the LED indicator do not light when a
signal is received or a key is pushed.
selected DTMF code.
COMPANDER KEY
RE-DIAL KEY
Push to transmit the last-transmitted DTMF code.
• TX memories are cleared after turning the transceiver OFF.
Push to toggle the compander function ON and OFF.
The compander function reduces noise components from the
transmitted audio to provide clear communication.
5
PANEL DESCRIPTION
1
TX CODE ENTER KEY (PMR or BIIS PMR operation only)
Push to enter the ID code edit mode directly, for both 5-tone
and MSK. Then set the desired digit using [CH Up]/
[CH Down]. (p. 11)
TX CODE CHANNEL SELECT KEY
➥ Push to enter the ID code channel selection mode directly.
Then set the desired channel using [CH Up]/[CH Down].
(p. 10)
➥ During ID code channel selection mode, push for 1 sec. to
enter the ID code edit mode for 5-tone and MSK. Then set
the desired digit using [CH Up]/[CH Down]. (p. 11)
TX CODE CHANNEL UP/DOWN KEYS
➥ Push to select a TX code channel directly.
➥ Push to set the desired digit during the ID code edit mode.
ID-MR SELECT KEY (PMR or BIIS PMR operation only)
➥ Recalls detected ID codes.
• Push this key, then select the ID code using [CH Up]/[CH Down].
• Up to 5 ID’s are memorized.
➥ Push and hold for 1 sec. to erase the selected ID’s.
HOOK SCAN KEY
When the on hook scan function is activated, push this key
to disables on hook scan function (stop scanning) temporarily. Push this key again to re-start scanning.
USER SET MODE KEY
➥ Push and hold to enter user set mode.
• During user set mode, push this key to select an item, and
change the value or condition using push [CH Up]/[CH Down].
➥ Push and hold this key again to exit user set mode.
User set mode is also available via the ‘Power ON function.’
Refer to p. 14 also.
MR-CH ENT KEYS
Push to enter the memory channel selection mode, then enter
the desired channel number using the 10-keypad of the connected microphone.
OPT 1/2/3 KEYS
Push to control the output signal level from the optional unit
connector.
1
6
PANEL DESCRIPTION
1
D For Digital mode operation only
TALKGROUP KEY
Push to enter the talkgroup ID code selection mode. Then
select the desired talkgroup ID code using [CH Up]/[CH
Down]. (p. 12)
TX STATUS KEY
Push to enter the Status message selection mode. Then
select the desired Status message using [CH Up]/[CH Down].
(p. 12)
TONE/RAN CH SELECT KEY
➥ While in the analog mode operation, push to select the
continuous tone channel using [CH Up] or [CH Down] to
change the tone frequency/code setting.
➥ While in the digital mode operation, push to select the RAN
channel using [CH Up] or [CH Down] to change the RAN
code setting.
➥ While in the mixed (digital and analog) mode operation,
push to select the continuous tone channel using [CH Up]
or [CH Down] to change the tone frequency/code setting.
Then push this key to enter the setting. After that, the RAN
channel selection screen appears. Select the RAN channel
using [CH Up] or [CH Down] to change the RAN code setting. Then push this key to enter the setting.
7
BASIC OPERATION
KEY
NUMBER
0
5
4
9
3
8
2
7
1
6
2
■ Turning power ON
q Push []to turn the power ON.
w If the transceiver is programmed for a start up password,
input the digit codes as directed by your dealer.
• The keys as below can be used for password input:
The transceiver detects numbers in the same block as identical.
Therefore “01234” and “56789” are the same.
e When the “PASSWORD” indication does not clear after
inputting 6 digits, the input code number may be incorrect.
Turn the power off and start over in this case.
■ Channel selection
Several types of channel selections are available. Methods
may differ according to your system set up.
NON-ZONE TYPE:
Push [CH Up] or [CH Down] to select the desired operating
channel, in sequence; or, push one of [MR-CH 1] to [MR-CH
4] keys to select a channel directly.
ZONE TYPE:
Push [Zone] then push [CH Up] or [CH Down] to select the
desired zone.
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning
power ON, the transceiver automatically starts scanning.
Scanning stops when receiving a call.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
8
BASIC OPERATION
Selective calling
Non-selective calling
2
■ Call procedure
When your system employs tone signaling (excluding CTCSS
and DTCS), the call procedure may be necessary prior to voice
transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s)
only and prevent unwanted stations from contacting you.
q Select the desired TX code channel, 2/5-tone code or
w Push the call key (assigned to one of the dealer program-
e After transmitting, the remainder of your communication
9
Talkgroup ID code* according to your System Operator’s
instructions.
• This may not be necessary depending on programming.
• Refer to pgs. 10–12 for selection.
*Digital mode operation only.
mable keys; except for the Digital mode operation) or [PTT].
can be carried out in the normal fashion.
■ Receiving and transmitting
Receiving:
q Push [ ] to turn the power ON.
w Push [CH Up] or [CH Down] to select a channel, in
sequence.
e When receiving a call, adjust the audio output level to a
comfortable listening level.
Transmitting:
Wait for the channel to become clear to avoid interference.
q Take the microphone off hook.
• 2/5-tone mute may be released. (The ‘audible’ condition is
selected and BUSY indicator lights green.)
• A priority channel may be selected automatically.
w Wait for the channel to become clear.
• The channel is busy when BUSY indicator lights green.
e Push [CALL] when initiating a call from your side.
• Coded audio may be heard from the transceiver, then “ ”
appears.
• This operation may not be necessary depending on your signaling system. Ask your dealer for details.
r While pushing and holding [PTT], speak into the micro-
phone at your normal voice level.
t Release [PTT] to receive.
IMPORTANT: To maximize the readability of your signal;
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 inches) from
your mouth, then speak into the microphone at a normal
voice level.
BASIC OPERATION
2
D Transmitting notes
• Transmit inhibit function
The transceiver has several inhibit functions which restrict
transmission under the following conditions:
- The channel is in mute condition (‘Inaudible’ condition;
“ ” does not appear.)
- The channel is busy.
- Un-matched (or matched) CTCSS is received.
(Depending on the pre-setting)
- Un-matched (or matched) RAN is received.*
(Depending on the pre-setting)
- The selected channel is a ‘receive only’ channel.
*Digital mode operation only.
• Time-out timer
After continuous transmission for the pre-programmed time
period, the time-out timer is activated, causing the transceiver to stop transmitting.
• Penalty timer
Once the time-out timer is activated, transmission is further
inhibited for a period determined by the penalty timer.
D TX code channel selection
If the transceiver has [TX Code CH Select] assigned to it, the
indication can be toggled between the operating channel
number (or name) and TX code channel number (or name).
When the TX code channel number (or name) is displayed,
[CH Up]/[CH Down] selects the TX code channel.
USING [TX CODE CH SELECT] KEY:
q Push [TX Code CH Select]— a TX code channel number
(or name) appears.
w Push [CH Up] or [CH Down] to select the desired TX code
channel.
e Push [Call] to transmit the selected TX code.
USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY:
If the transceiver has a [TX Code CH Up] or [TX Code CH
Down] key assignment, the programmed TX code channel
can be selected directly when pushed.
NOTE for PMR or BIIS PMR operation:
• The LCD indication does not change when the operating
channel number (or name) is displayed.
• To check the selected TX code, push [TX Code CH
Select].
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
10
BASIC OPERATION
2
D TX code number edit
(PMR or BIIS PMR operation only)
If the transceiver has [TX Code CH Select] or [TX Code
Enter] assigned to it, TX code contents can be edited within
the allowable digits.
USING [TX CODE CH SELECT] KEY:
q Push [TX Code CH Select] to enter the TX code channel
selection mode.
• Select the desired channel before entering the TX code channel
selection mode if necessary.
w Push [TX Code CH Select] for 1 sec. to enter the TX code
edit mode.
e Push [TX Code CH Select] to select the desired digit to be
edited.
• The digit to be edited blinks.
r Push [CH Up] or [CH Down] to set the desired digit.
t Push [TX Code CH Select] to set the digit. The digit to the
right will blink automatically.
y Repeat r and t to input all allowable digits.
u Push [Call] to transmit the edited TX code.
USING [TX CODE ENTER] KEY:
q After pushing [TX Code CH Select], push [CH Up] or [CH
Down], or push [TX Code CH Up] or [TX Code CH Down]
to select the desired TX code channel.
w Push [TX Code Enter] to enter the TX code edit mode.
• The digit to be edited blinks.
e Push [TX Code Enter] to select the desired digit to be edit-
ed.
r Push [CH Up] or [CH Down] to set the desired digit.
t Push [TX Code Enter] to set the digit. The digit to the right
will blink automatically.
y Repeat r and t to input all allowable digits.
u Push [Call] to transmit the edited TX code.
11
BASIC OPERATION
STATUS 01
TX Status 01
When the 2 lines indication mode is selected.
Status messageStatus channel
TGID01
When the 2 lines indication mode is selected
and [Talkgroup] is assigned to [P0].
Talkgroup ID name
Appears above the
key that [Talkgroup]
is assinged after
pushed.
2
D Talkgroup ID code selection
(Digital mode operation only)
If the transceiver has [Talkgroup] assigned to it, the indication
can be toggled between the operating channel name (and the
channel number)* and the Talkgroup ID name (or ID code if
the ID name is not programmed.) When the Talkgroup ID
name (or ID code) is displayed, [CH Up] or [CH Down] selects
the desired Talkgroup ID name (or ID code).
q Push [Talkgroup]— Talkgroup ID name (or ID code)
appears.
w Push [CH Up] or [CH Down] to select the desired
Talkgroup ID name (or ID code).
e Push [PTT] to transmit the selected Talkgroup ID.
D TX Status message selection
(Digital mode operation only)
If the transceiver has [TX Status] assigned to it, the indication
can be toggled between the operating channel name (and the
channel number)* and the Status message (and the Status
channel.)* When the Status message (and the Status channel)* is displayed, [CH Up] or [CH Down] selects the desired
Status message.
q Push [TX Status]— Status message (and Status channel)*
appears.
w Push [CH Up] or [CH Down] to select the desired Status
message.
e Push [PTT] to transmit the selected Status message.
* Only when the 2 lines indication mode is selected.
2
12
BASIC OPERATION
2
D DTMF transmission
If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. Up to 8 DTMF
channels are available.
q Push [DTMF Autodial]— a DTMF channel appears.
w Push [CH Up] or [CH Down] to select the desired DTMF
channel.
e Push [DTMF Autodial] to transmit the DTMF code in the
selected DTMF channel.
■ Scrambler function
The voice scrambler function provides private communication
between stations. The frequency inversion type is equipped
to all versions, moreover, the optional Rolling or Non-rolling
type can be available.
q Push [Scrambler] to turn the scrambler function ON.
• “ ” appears.
w Push [Scrambler] again to turn the scrambler function
OFF.
• “ ” disappears.
13
■ User set mode
[ ]
[P0] [Up]/[Down]
[P1][P0] [P2] [ ]
User set mode is accessed with [User Set Mode] and allows
you to set seldom-changed settings. In this case you can
“customize” the transceiver operation to suit your preferences
and operating style.
Entering the user set mode:
q While pushing and holding [P1] and [P2], push [ ] to turn
the power ON. Then, push and hold [P0] for 1 sec. to enter
user set mode.
• You should hold [P1] and [P2] until “SET MODE” appears.
w Push [P0] several times to select the appropriate item.
Then, push [Up] or [Down] to set the desired level/condition.
• Available set mode functions are Backlight, LCD Contrast,
Beep, Beep Level, Ringer Level, SQL Level, AF Min Level,
Mic Gain, Horn and Signal Moni.
BASIC OPERATION
e Push and hold [ ] for 1 sec. to turn power OFF, then ON
again to exit set mode.
User set mode is also available via a programmable key.
Please refer to p. 6 [User Set Mode] section.
2
2
14
3
CONNECTION AND MAINTENANCE
■ Rear panel connection
Antenna
q ANTENNA CONNECTOR
Connects to an antenna.
Contact your dealer about
antenna selection and
placement.
w D-Sub 25-pin
Connect an external unit.
e EXTERNAL
SPEAKER JACK
Connect a 4–8 Ω
external speaker.
Optional speaker
Microphone
15
q
y DC POWER RECEPTACLE
Connects to a 12 V DC battery. Pay attention to polarities. NEVER connect to a 24 V
battery. This could damage the transceiver.
Red
12V
Battery
R CAUTION! NEVER remove
the fuse-holder from the DC
power cable.
t
Black
e
y
w
NOTE: Use the terminals as shown
below for the cable connections.
Crimp
Solder
r
r MICROPHONE HANGER
Connect the supplied microphone hanger to the
vehicle’s ground for microphone on/off hook
functions. (See p. 1)
t IGNITION LEAD
Connects to a ignition line.
R
Do not put a pressure to
this lead.
Binding to the DC power
cable is recommended.
CONNECTION AND MAINTENANCE
Flat washer
Felt*
Spring washer
When using
self-tapping screws
Felt*
*Felts reduce the vibration effects.
Microphone
Microphone hanger
and screw set
Microphone
hanger cable
DC power cable Sponges*
2
Mounting bracket
and felts
Flat washers
Spring washers
Bracket bolts
Mounting screws
(M5×12)
Self-tapping screws
(M5×16)
Nuts
Function name
stickers*
1
Felts are already
attached.
*
2
Used for labelling the programmable
function keys according to their assinged functions.
Used for the optional unit installation.
Ask your dealer for details.
*
1
3
■ Supplied Accessories ■ Mounting the transceiver
1
The universal mounting bracket supplied with your transceiver allows overhead mounting.
•Mount the transceiver securely with the 4 supplied screws
to a thick surface which can support more than 1.5 kg.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16
CONNECTION AND MAINTENANCE
3
17
■ Antenna
A key element in the performance of any communication system is an antenna. Contact your dealer about antennas and
the best places to mount them.
■ Fuse replacement
A fuse is installed in the supplied DC power cable. If a fuse
blows or the transceiver stops functioning, track down the
source of the problem if possible, and replace the damaged
fuse with a new rated one.
❑ Fuse rating: 20 A
USE the 20 A fuse only.
■ Cleaning
If the transceiver becomes dusty or dirty, wipe it clean with a
soft, dry cloth.
AVOID the use of solvents such as benzene or
alcohol, as they may damage the transceiver surfaces.
■ Options
• RMK-3
OPC-607/OPC-608/OPC-609
Allows you to install the transceiver main unit separately
from the front panel for operating convenience.
• SP-5/SP-10/SP-22
Input impedance : 4 Ω
Max. input power : 5 W
SP-5 : Large speaker for good audio quality.
SP-10 : For all-round mobile operation.
SP-22 : Compact and easy-to-install.
• HM-152/HM-152T/HM-148
HM-152 : Hand microphone
HM-152T : DTMF microphone
HM-148 : Heavy duty microphone
• SM-25
• UT-109R/UT-110R
Non-rolling type (UT-109R)/Rolling type (UT-110R) voice
scrambler unit provides higher communication security.
• UT-96R
• UT-119H
Provides 6.25/12.5 kHz narrow bandwidth digital mode
operation.
SEPARATION KIT
DESKTOP MICROPHONE
5
TONE UNIT
DIGITAL MODULATOR
+
EXTERNAL SPEAKER
SCRAMBLER UNITS
SEPARATION CABLE
HAND MICROPHONE
/
DEMODULATOR UNIT
SAFETY TRAINING INFORMATION
WARNING
CAUTION
4
• For compliance with FCC and Industry Canada RF Exposure
Your Icom radio generates RF electromagnetic
energy during transmit mode. This radio is
designed for and classified as “Occupational Use
Only”, meaning it must be used only during the
course of employment by individuals aware of the
hazards, and the ways to minimize such hazards.
This radio is NOT intended for use by the “General
Population” in an uncontrolled environment.
Requirements, the transmitter antenna installation shall comply with
the following two conditions:
1. The transmitter antenna gain shall not exceed 0 dBi.
2. IC-F5061:
The antenna is required to be located outside of a vehicle and
kept at a distance of 48 centimeters or more between the transmitting antenna of this device and any persons during operation.
For small vehicle as worst case, the antenna shall be located on
the roof top at any place on the centre line along the vehicle in
order to achieve 48 centimeters separation distance. In order to
ensure this distance is met, the installation of the antenna must
be mounted at least 48 centimeters away from the nearest edge
of the vehicle in order to protect against exposure to bystanders.
2. IC-F6061:
The antenna is required to be located outside of a vehicle and
kept at a distance of 38 centimeters or more between the transmitting antenna of this device and any persons during operation.
For small vehicle as worst case, the antenna shall be located on
the roof top at any place on the centre line along the vehicle in
order to achieve 38 centimeters separation distance. In order to
ensure this distance is met, the installation of the antenna must
be mounted at least 38 centimeters away from the nearest edge
of the vehicle in order to protect against exposure to bystanders.
To ensure that your exposure to RF electromagnetic energy is within the FCC allowable limits
for occupational use, always adhere to the following guidelines:
•DO NOT operate the radio without a proper antenna attached, as
this may damage the radio and may also cause you to exceed FCC
RF exposure limits. A proper antenna is the antenna supplied with
this radio by the manufacturer or an antenna specifically authorized
by the manufacturer for use with this radio.
•DO NOT transmit for more than 50% of total radio use time (“50%
duty cycle”). Transmitting more than 50% of the time can cause FCC
RF exposure compliance requirements to be exceeded. The radio
is transmitting when the “TX indicator” lights red. You can cause the
radio to transmit by pressing the “PTT” switch.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that can
possibly cause interference with other devices or systems. To avoid
such interference, turn off the radio in areas where signs are posted
to do so. DO NOT operate the transmitter in areas that are sensitive
to electromagnetic radiation such as hospitals, aircraft, and blasting
sites.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
MEMO
MEMO
A-6565D-1EX-q
Printed in Japan
© 2006–2007 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Loading...