Page 1
INSTRUCTIONS
VHF TRANSCEIVERS
|F3260 series
UHF TRANSCEIVERS
|F4260 series
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
SAVE THIS INSTRUCTIONS — This instruction sheet
contains important operating instructions for the
IC-F3261DT/DS, IC-F3262DT/DS, IC-F3263DT/DS
VHF TRANSCEIVERS, and the IC-F4261DT/DS,
IC-F4262DT/DS, IC-F4263DT/DS UHF TRANSCEIVERS.
IMPORTANT
This instruction sheet includes some functions that are
usable only when they are preset by your dealer. The
transceiver may have other functions and operations that
are not described in this instruction sheet. Ask your dealer
for preset function details.
The GPS receiver may not work if the transceiver
transmits near 510 MHz. This is due to the internal
circuitry and does not indicate a transceiver malfunction.
EXPLICIT DEFINITIONS
WORD DEFINITION
R DANGER!
R WARNING!
CAUTION Equipment damage may occur.
NOTE
Icom is not responsible for the destruction, damage to,
or performance of any Icom or non-Icom equipment, if
the malfunction is because of:
• Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
• The use of Icom transceivers with any equipment that
is not manufactured or approved by Icom.
Icom, Icom Inc. and Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia,
Australia, New Zealand, and/or other countries.
AMBE+2 is a trademark and property of Digital Voice
Systems Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
1-1-32 Kamiminami, Hirano-ku,
Osaka 547-0003, Japan
Apr. 2020
Personal death, serious injury or an
explosion may occur.
Personal injury, re hazard or electric
shock may occur.
If disregarded, inconvenience only. No risk
of personal injury, re or electric shock.
A7016D-1EX-9
Printed in Japan
© 2012–2020 Icom Inc.
FCC INFORMATION
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION: Changes or modications to this transceiver,
not expressly approved by Icom Inc., could void your
authority to operate this transceiver under FCC regulations.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this device does
not cause harmful interference.
PRECAUTIONS
R DANGER! NEVER short the terminals of the battery
pack. Shorting may occur if the terminals touch metal
objects such as a key, so be careful when placing the
battery packs (or the transceiver) in bags, and so on.
Carry them so that shorting cannot occur with metal
objects. Shorting may damage not only the battery pack,
but also the transceiver.
R DANGER! NEVER operate the transceiver near
unshielded electrical blasting caps. This could cause an
explosion and death.
R DANGER! NEVER use and charge Icom battery packs
with non-Icom transceivers or non-Icom chargers. Only
Icom battery packs are tested and approved for use with
Icom transceivers or charged with Icom chargers. Using
third-party or counterfeit battery packs or chargers may
cause smoke, re, or cause the battery to burst.
R WARNING! NEVER operate with earphone,
headphones or other audio accessories at high volume
levels. If you experience a ringing in your ears, reduce the
volume level or discontinue use.
R WARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention—
anything less could result in an accident.
CAUTION: DO NOT use harsh solvents such as Benzine
or alcohol when cleaning. This could damage the
equipment surfaces. If the surface becomes dusty or dirty,
wipe it clean with a soft, dry cloth.
CAUTION: DO NOT carry the transceiver by holding the
antenna.
CAUTION: DO NOT operate the transceiver unless the
exible antenna, battery pack, and jack cover are securely
attached to the transceiver, and that the antenna and
battery pack are dry before attachment. Exposing the
inside of the transceiver to dust or water will result in
serious damage to the transceiver.
CAUTION: DO NOT place or leave the transceiver in areas
with temperatures below –25°C (–13°F) or above +55°C
(+131°F): European version, below –30°C (–22°F) or above
+60°C (+140°F): other versions. The basic operations of the
transceiver are guaranteed within the specied operating
temperature range. However, the Liquid Crystal Display
may not operate correctly, or show an indication in the
case of long hours of operation, or after being placed in
extremely cold areas.
CAUTION: DO NOT modify the transceiver. The
specications may change and then the transceiver may
not comply with the requirements of required regulations.
The transceiver warranty does not cover any problems
caused by unauthorized modication.
BE CAREFUL! The transceiver will become hot when
operating it continuously for long periods of time.
BE CAREFUL! The transceiver meets IP67* requirements
for dust-tight and waterproof protection. However, once the
transceiver has been dropped, dust tight and waterproof
protection cannot be guaranteed because of possible
damage to the transceiver’s case or the waterproof seal.
* Only when the supplied battery pack, exible antenna
and connector cover are attached.
Even when the transceiver power is OFF, a slight current
still ows in the circuits. Remove the battery pack from the
transceiver when not using it for a long time. Otherwise,
the installed battery pack will become exhausted, and will
need to be recharged or replaced.
ALWAYS turn OFF the transceiver before connecting any
external devices.
D Battery caution
Misuse of Li-ion batteries may result in the following
hazards: smoke, re, or the battery may rupture. Misuse
can also cause damage to the battery or degradation of
battery performance.
R DANGER! NEVER leave battery pack in places with
temperatures above +60°C (+140°F). High temperature
buildup in the battery cells, such as could occur near res or
stoves, inside a sun-heated vehicle, or in direct sunlight for
long periods of time may cause the battery cells to rupture
or catch re. Excessive temperatures may also degrade
pack’s performance or shorten the battery cell’s life.
R DANGER! NEVER solder the battery cell’s terminals,
or NEVER modify the battery pack. This may cause heat
generation, and the battery cells may burst, emit smoke or
catch re.
R DANGER! NEVER strike or otherwise impact the
battery pack. Do not use the pack if it has been severely
impacted or dropped, or if it has been subjected to heavy
pressure. Battery damage may not be visible on the
outside of the case. Even if the surface of the pack does
not show cracks or any other damage, the cells inside the
pack may rupture or catch re.
R DANGER! NEVER expose the battery pack to rain,
snow, seawater, or any other liquids. Do not charge or
use a wet pack. If the pack gets wet, be sure to wipe it dry
before using. The battery pack itself is not waterproof.
R DANGER! NEVER place battery packs near a re. Fire
or heat may cause them to rupture or explode. Dispose of
used packs in accordance with local regulations.
R DANGER! NEVER use the battery pack with a
transceiver for which it is not specied. Never use a pack
with any other equipment, or for any purpose that is not
specied in the instruction manual.
R DANGER! NEVER let uid from inside the battery cells
get in your eyes. If it does, blindness can result. Rinse
your eyes with clean water, without rubbing them, and
immediately go to a doctor.
R WARNING! NEVER put the battery pack in a microwave
oven, high-pressure container, or in an induction heating
cooker. This could cause a re, overheating, or cause the
battery cells to rupture.
R WARNING! NEVER use the battery pack if it emits an
abnormal odor, heats up, or is discolored or deformed. If any of
these conditions occur, contact your Icom dealer or distributor.
R WARNING! NEVER use deteriorated battery packs.
They could cause a re.
R WARNING! NEVER let uid from inside the battery cells
come in contact with your body. If it does, immediately
wash with clean water.
CAUTION: DO NOT use the battery pack out of the
specied temperature range, for the transceiver (–25°C ~
+55°C, –13°F ~ +131°F for European version, or –30°C ~
+60°C, –22°F ~ +140°F for other versions), and the battery
pack itself (–20°C ~ +60°C,–4°F ~ +140°F). Using the
pack out of the specied temperature range will reduce it’s
performance and the battery cell’s life.
CAUTION: Shorter battery pack life could occur if the
pack is left fully charged, completely discharged, or in an
excessive temperature environment (above +50˚C, +122˚F)
for an extended period of time. If the battery pack must be
left unused for a long time, it must be detached from the
transceiver after discharging. You may use the pack until
the remaining capacity is about half, then keep it safely in a
cool dry place in the following temperature range:
–20˚C (–4˚F) ~ +50˚C (+122˚F) (for a month)
–20˚C (–4˚F) ~ +35˚C (+95˚F) (for three months)
–20˚C (–4˚F) ~ +20˚C (+68˚F) (for a year)
BE SURE to replace the battery pack with a new one
approximately ve years after manufacturing, even if it still
holds a charge. The material inside the battery cells will
become weak after a period of time, even with little use.
The estimated number of times you can charge the pack
is between 300 and 500. Even when the pack appears to
be fully charged, the operating time of the transceiver may
become short when:
• Approximately ve years have passed since the pack
was manufactured.
• The pack has been repeatedly charged.
D Charging caution
R DANGER! NEVER charge the battery pack in areas
with extremely high temperatures, such as near res or
stoves, inside a sun-heated vehicle, or in direct sunlight. In
such environments, the safety/protection circuit in the pack
will activate and stop the charging.
R WARNING! NEVER charge the transceiver during a
lightning storm. It may result in an electric shock, cause
a re or damage the transceiver. Always disconnect the
power adapter before a storm.
R WARNING! NEVER charge or leave the battery pack in
the battery charger beyond the specied time for charging. If
the pack is not completely charged by the specied time, stop
charging and remove it from the battery charger. Continuing
to charge the pack beyond the specied time limit may cause
a re, overheating, or the battery cells may rupture.
R WARNING! Occasionally observe the battery pack
condition while charging. If any abnormal condition occurs,
discontinue using the battery pack.
R WARNING! NEVER insert the transceiver (with the
battery pack attached) into the charger if it is wet or
soiled. This could corrode the battery charger terminals or
damage the charger. The charger is not waterproof.
CAUTION: DO NOT charge the battery outside of the
specied temperature range:
BC-160/BC-171 10˚C ~ 45˚C (50˚F ~ 113˚F)
BC-119N/BC-121N/BC-197 10˚C ~ 40˚C (50˚F ~ 104˚F)
Icom recommends charging the battery at 20˚C, (68˚F).
Otherwise, the charging time will be longer, but the battery
will not reach a full charge. While charging, at a point
after the temperature goes out of the specied range, the
charging will automatically stop.
SAFETY TRAINING INFORMATION
Your Icom radio generates RF
electromagnetic energy while
transmitting. This radio is designed for
and classied as for “Occupational Use
Only.” This means it must be used only
during the course of employment by
individuals aware of the hazards, and the
radio is NOT intended for use by the “General Population”
in an uncontrolled environment. This radio has been tested
and complies with the FCC and IC RF exposure limits for
“Occupational Use Only”. In addition, your Icom radio
complies with the following Standards and Guidelines with
regard to RF energy and electromagnetic energy levels
and evaluation of such levels for exposure to humans:
• FCC KDB Publication 447498 D03, Evaluating
Compliance with FCC Guidelines for Human Exposure
to Radio Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992),
IEEE Standard for Safety Levels with Respect to
Human Exposure to Radio Frequency Electromagnetic
Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3-1992),
IEEE Recommended Practice for the Measurement of
Potentially Hazardous Electromagnetic Fields– RF and
Microwave.
• The antennas, batteries, belt clips, speaker-microphone,
and other accessories that are listed in “OPTIONS”
on this sheet, are authorized for use with this product.
Use of accessories other than those specied may
result in RF exposure levels exceeding the FCC and IC
requirements for wireless RF exposure.
• Health Canada Safety Code 6 - Limits of Human
Exposure to Electromagnetic Energy in the Frequency
Range from 3 kHz to 300 GHz.
• DO NOT operate the radio without a proper antenna
attached, as this may damage the radio and may also
cause you to exceed FCC and IC RF exposure limits.
A proper antenna is the antenna supplied with this
radio by the manufacturer or an antenna specically
authorized by the manufacturer for use with this radio.
• DO NOT transmit for more than 50% of the total radio
use time (“50% duty cycle”). Transmitting more than
50% of the time can cause FCC and IC RF exposure
compliance requirements to be exceeded. The radio is
transmitting when the status indicator lights red. You
can cause the radio to transmit by pushing the “PTT”
switch or VOX function.
• ALWAYS keep the antenna at least 2.5 cm (1 inch)
away from the body when transmitting, and only use
the Icom belt-clips listed in “OPTIONS” on this sheet
when attaching the radio to your belt, or other place,
to ensure FCC and IC RF exposure compliance
requirements are not exceeded.
The information listed above provides t he user with
the information needed to make him or her aware of
RF exposure, and what to do to assure that this radio
operates within the FCC and IC RF exposure limits of
this radio.
ways to minimize such hazards. This
To ensure that your expose to RF
electromagnetic energy is within the FCC
and IC allowable limits for occupational
use, always adhere to the following
guidelines:
• Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF
energy that can possibly cause interference with other
devices or systems. To avoid such interference, turn o
the radio in areas where signs are posted to do so. DO
NOT operate the transmitter in areas that are sensitive
to electromagnetic radiation such as hospitals, aircraft,
and blasting sites.
• Occupational/Controlled Use
The radio transmitter is used in situations in which
persons are exposed as a consequence of their
employment, provided those persons are fully aware of
the potential for exposure and can exercise control over
their exposure.
ABOUT CE AND DOC
Hereby, Icom Inc. declares that the
versions of IC-F3262DT, IC-F3262DS,
IC-F4262DT, and IC-F4262DS which
have the “CE” symbol on the product,
of the Radio Equipment Directive, 2014/53/EU, and the
restriction of the use of certain hazardous substances in
electrical and electronic equipment Directive, 2011/65/EU.
The full text of the EU declaration of conformity is available
at the following internet address:
https://www.icomjapan.com/support/
DISPOSAL
municipal waste. Dispose of them according to the laws in
your area.
comply with the essential requirements
The crossed-out wheeled-bin symbol on
your product, literature, or packaging
reminds you that in the European Union, all
electrical and electronic products, batteries,
and accumulators (rechargeable batteries)
must be taken to designated collection
locations at the end of their working life. Do
not dispose of these products as unsorted
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed
solely for use within this Communications Equipment.
The user of this Technology is explicitly prohibited from
attempting to extract, remove, decompile, reverse
engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form.
U.S. Patent Nos. #8,595,002, #8,359,197, #8,315,860,
#8,200,497, #7,970,606, #6,912,495 B2.
RECOMMENDATION
CLEAN THE TRANSCEIVER THOROUGHLY IN A BOWL
OF FRESH WATER after exposure to saltwater, and dry
it before operating. Otherwise, the transceiver’s keys,
switches, and controllers may become unusable, due to
salt crystallization, and/or the charging terminals of the
battery pack may corrode.
NOTE: If the transceiver’s waterproof protection appears
defective, carefully clean it with a soft, damp (fresh water)
cloth, then dry it before operating.
The transceiver may lose its waterproof protection if the case,
jack cap, or connector cover is cracked or broken, or the
transceiver has been dropped, or the battery pack is detached.
Contact your Icom distributor or your dealer for advice.
SUPPLIED ACCESSORIES
Flexible Antenna
( This illustration is
of the UHF type.)
NOTE: Some accessories are not supplied, or the shape
is dierent, depending on the transceiver version.
D Battery pack
CAUTION: DO NOT attach or detach the battery pack
when the transceiver is wet or soiled. This may result in
water or dust getting into the transceiver/battery pack and
may damage the transceiver.
To attach:
Slide the battery pack in the direction of the arrow (1) until
the battery release button makes a ‘click’ sound.
NOTE: Push on the bottom of the pack to conrm the
release button is rmly locked.
To detach:
1. Push the battery release button in the direction of the
arrow (2).
2. Detach the battery pack.
NOTE: Keep the battery pack terminals clean. It’s a good
idea to occasionally clean them.
Battery pack
Battery pack Belt clip
1
Battery release
2
button
Connector cover
(With screw)
D Flexible antenna
Connect the supplied exible antenna to the antenna
connector.
CAUTION:
• DO NOT carry the transceiver by holding only the
antenna.
• DO NOT connect any antenna other than those listed
in the “OPTIONS” section.
• Transmitting without an antenna may damage the
transceiver.
D Belt clip
To attach:
1. Remove the battery pack if it is attached.
2. Slide the belt clip in the direction of the arrow until the
belt clip locks and makes a ‘click’ sound.
To detach:
1. Remove the battery pack if it is attached.
2. Gently lift up the clip (1), and slowly slide the belt clip
in the direction of the arrow (2).
w
q
BE CAREFUL! Do not break your ngernail.
Page 2
PANEL DESCRIPTION
There are 2 types of transceivers in the IC-F3260 and
IC-F4260 series.
IC-F3260DS / IC-F4260DS: Simple key type
IC-F3260DT / IC-F4260DT: Ten-key type
The illustration below shows the Ten-key type transceiver.
[Rotary Selector]
Antenna
connector
2
[Emer]*
2
[Side1]*
[PTT]
2
[Side2]*
2
[Side3]*
1
*
Built in, depending on the transceiver version.
2
*
Dealer assignable
D About the Status indicator
• Lights red while transmitting.
• Lights green while receiving a signal, or when the
squelch is open.
• Blinks red when the battery is exhausted.
D About the Multi-connector
Connects to an optional speaker microphone or headset.
CAUTION: BE SURE to attach the connector cover
when an optional accessory is not used. The transceiver
meets IP67 requirements for dust-tight and waterproof
protection only when the connector cover or the optional
HM-184/HM-184H is attached.
[VOL]
GPS receiver *
Status indicator
Speaker
Multi-connector
Microphone
Function
display
2
, [P1]*2,
[P0]*
2
[P2]*
, [P3]*
Ten-key pad
BATTERY CHARGING
D FUNCTION DISPLAY
1 2 3 4 567 8
NOTE: Before detaching or attaching a battery pack,
BE SURE to turn OFF the transceiver by rotating [VOL]
fully counter clockwise, until it makes a “click” sound.
Otherwise, a transceiver malfunction could occur.
IMPORTANT: Battery charging caution
Be sure the guide tabs on the battery pack are correctly
aligned with the guide rails inside the charger.
9
1
CALA TXCU
SIGNAL STRENGTH ICON
1
Displays the relative receive signal strength.
2LOW POWER ICON
Displayed when low output power is selected.
L When the battery charge decreases to a specied level,
low power is automatically selected.
2
3AUDIBLE ICON
• Displayed when the channel is in the audible
(unmuted) mode.
• Displayed when a matching signal is received.
4COMPANDER ICON
Displayed when the Compander function is ON.
5SCRAMBLER ICON
Displayed when the Voice Scrambler function is ON.
6BELL ICON
Displayed when a matching signal is received,
depending on the presetting.
7CALL CODE MEMORY ICON
Displayed when the call code memory is selected.
8BATTERY ICON
Displays the battery level.
Indication
Battery
Status
L
blinks when the battery is exhausted.
9ALPHANUMERIC DISPLAY
• Displays the operating channel number, channel
name, Set mode contents, DTMF code, and so on.
• Depending on the presetting, characters are
displayed in 1 line or 2 lines on the display.
L In this instruction sheet illustration, characters are
displayed in 2 lines.
KEY ICONS
Displays the assigned function of the [P0], [P1], [P2]
and [P3] front panel keys.
TXC
Full Mid
SET
Charging
required
Battery
exhausted
Tabs
Guide rail
D Charging with the BC-160/BC-171
You can rapidly charge the Li-ion battery pack with the
BC-160, or regularly charge the pack with the BC-171.
Charging time for the BP-232WP
BC-160: Approximately 3.5 hours
BC-171: Approximately 11.5 hours
Additionally needed item (purchase separately):
• A power adapter (may be supplied with the charger,
depending on the charger version) or the DC power
cable (OPC-515L).
Transceiver
Power adapter
Optional OPC-515L (for a 13.8 V power source) or CP-23L
(for a cigarette lighter socket) can be used instead of a
power adapter.
Battery
pack
L This illustration is for the BC-160.
+ battery pack
Turn OFF
D Rapid charging with the BC-119N+AD-106
You can rapidly charge the Li-ion battery pack with the
BC-119N.
Charging time for the BP-232WP:
Approximately 3.5 hours
Additionally needed item (purchase separately):
• An AD-106 charger adapter
• A power adapter (may be supplied, depending on the
charger version) or the DC power cable (OPC-515L/CP-23L)
Transceiver
+ battery pack
Battery
pack
Power adapter
Optional OPC-515L* (for a 13.8 V power source) or
CP-23L (for a 12 V cigarette lighter socket) can be used
instead of the power adapter.
* Polarity of the OPC-515L: White line: + Black line: _
CAUTION: DO NOT reverse the polarity when
connecting the OPC-515L or OPC-656 to a power
source. This will ruin the battery charger.
Turn OFF
AD-106 charger
adapter installed
in the BC-119N.
D AD-106 installation
The AD-106 CHARGER ADAPTER must be installed
into the BC-119N DESKTOP CHARGER or the BC-121N
MULTI-CHARGER before charging the batteries.
1. Connect the BC-119N/BC-121N ribbon cables to the
AD-106.
2. Install the AD-106 into the holder space of the BC-
119N/ BC-121N with the supplied screws.
AD-106
Plugs
Screws
supplied with
the charger
adapter
Sockets
D Rapid charging with the BC-121N+AD-106
You can rapidly and simultaneously charge up to 6 battery
packs with the BC-121N.
Charging time for the BP-232WP:
Approximately 3.5 hours
Additionally needed item (purchase separately):
• Six AD-106 charger adapters
• A BC-157S power adapter or the OPC-656 DC power cable
To an AC outlet
Power
adapter
OPC-656* DC power cable
Connect to a 13.8 V, 7 A (minimum) power supply
* Polarity of the OPC-656: Red line:+ Black line:_
Battery
pack
Transceiver
+ battery pack
Turn OFF
AD-106 charger
adapters installed
in each slot.
D Charging with the BC-197+AD-122
You can rapidly and simultaneously charge up to 6 battery
packs with the BC-197.
Charging time for the BP-232WP:
Approximately 3.5 hours
L A power adapter may be supplied, depending on the
charger version.
L For details on the BC-197 multi-charger, see the
instruction manual supplied with the charger.
BASIC OPERATION
D Turning ON the transceiver
NOTE: Before using the transceiver for the rst time, the
battery pack must be fully charged for optimum life and
operation. See “BATTERY CHARGING” on this sheet.
Rotate [VOL] to turn ON the transceiver.
NOTE:
• If the transceiver is programmed for a start up password,
enter the digit codes as directed by your dealer.
• The battery type must be selected, according to the
attached battery type, when turning on the transceiver.
L Ask your dealer about entering the password or
selecting the battery type.
D Receiving and Transmitting
Receiving:
1. Select an operating channel.
zRotate [Rotary selector].
zPush [CH Up] or [CH Down].
zPush one of the direct channel select keys,
[MR-CH 1] to [MR-CH 4].
2. When receiving a call, rotate [VOL] to adjust the audio
output level.
Transmitting:
CAUTION: DO NOT transmit without an antenna. It may
damage the transceiver.
1. Wait until the channel is clear to avoid interference.
2. Hold down [PTT] to transmit.
3. Release [PTT] to receive.
IMPORTANT:
• To maximize the readability of your signal, push [PTT],
then pause briey before you start speaking.
• Hold the microphone 5 to 10 cm from your mouth, then
speak at your normal voice level.
FREQUENCY RANGE AND OUTPUT POWER
Model Version
VHF Transceviers
IC-F3260 series
USA-03
USA-04
USA-06
USA-23
USA-24
USA-26
EXP-07
EXP-27
UHF Transceivers
IC-F4260 series
• Channel spacing: 6.25 kHz*1/12.5 kHz/20 kHz*2/25 kHz*
*1 Only Digital mode
2
*
Only EUR and DPM versions
3
*
Except USA versions
AUS-01
AUS-21
EXP-04
EXP-05
EXP-06
EXP-24
EXP-25
EXP-26
DPM-25
Other 400–470 MHz
Frequency
Range
– 136–174 MHz 5 W
450–512 MHz
450–520 MHz
350–400 MHz
Output
Power
5 W
OPTIONS
D BATTERY PACKS
• BP-232WP LI-ION BATTERY PACK
Voltage: 7.4 V
Capacity: 2200 mAh (minimum) 2350 mAh (typical)
Battery life: Approximately 12 hours
When the power save function is ON, the GPS function
is OFF, and the operating periods are calculated under
the following conditions:
TX:RX:standby = 5 : 5 : 90
• BP-240/BP-261 BATTERY CASE
Battery case for AAA (LR03) × 6 alkaline
Battery case for AA (LR6) × 6 alkaline
The BP-240 and BP-261 have IPX4 waterproof
protection. When in use, the transceiver’s waterproof
rating meets IPX4.
D CHARGERS
• BC-119N DESKTOP CHARGER
+ AD-106 CHARGER ADAPTER
+ BC-145S POWER ADAPTER
To rapid charge battery packs.
A power adapter may be supplied, depending on the
charger version.
Charging time: Approximately 3.5 hours for the BP-232WP
• BC-121N MULTI CHARGER
+ AD-106 CHARGER ADAPTER (6 pieces)
+ BC-157S AC ADAPTER
To simultaneously rapid charge up to 6 battery packs.
A power adapter may be supplied, depending on the
charger version.
Charging time: Approximately 3.5 hours for the BP-232WP
• BC-160 DESKTOP CHARGER
+ BC-145S AC ADAPTER
To rapid charge battery packs.
A power adapter may be supplied, depending on the
charger version.
Charging time: Approximately 3.5 hours for the BP-232WP
• BC-171 DESKTOP CHARGER
+ BC-147S AC ADAPTER
To regular charge battery packs.
A power adapter may be supplied, depending on the
charger version.
Charging time: Approximately 11 hours for the BP-232WP
• BC-197 MULTI-CHARGER
+ AD-122 CHARGER ADAPTER (6 pieces)
+ BC-157S AC ADAPTER
To simultaneously rapid charge up to 6 battery packs.
A power adapter may be supplied, depending on the
charger version.
Charging time: Approximately 3.5 hours for the BP-232WP
D DC CABLES
• CP-23L CIGARETTE LIGHTER CABLES
Used when charging battery packs using a 12 V
cigarette lighter socket.
3
For use with the BC-119N/BC-160/BC-171.
• OPC-515L/OPC-656 DC POWER CABLES
Used when charging battery packs using a 13.8 V DC
power source instead of the power adapter.
OPC-515L: For the BC-119N/BC-160/BC-171
OPC-656: For the BC-121N/BC-197
L This illustration is for the BC-119N.
D BELT CLIPS
• MB-93 SWIVEL BELT CLIP
• MB-94R BELT CLIP
Alligator-type belt clip.
• MB-96N/MB-96F LEATHER BELT HANGER
D ANTENNAS
• FA-SC56VS/FA-SC57VS/FA-SC73US STUBBY ANTENNAS
Shorter VHF or UHF antennas.
FA-SC56VS: 150 ~ 162 MHz
FA-SC57VS: 160 ~ 174 MHz
FA-SC73US: 450 ~ 490 MHz
• FA-SC25V/FA-SC55V/FA-SC01U/FA-SC02U/FA-SC03U
FA-SC25U/FA-SC57U/FA-SC72U FLEXIBLE ANTENNAS
VHF or UHF antennas.
FA-SC25V: 136 ~ 150 MHz
FA-SC55V: 150 ~ 174 MHz
FA-SC01U: 350 ~ 400 MHz
FA-SC02U: 330 ~ 380 MHz
FA-SC03U: 380 ~ 430 MHz
FA-SC25U: 400 ~ 430 MHz
FA-SC57U: 430 ~ 470 MHz
FA-SC72U: 470 ~ 520 MHz
• FA-SC61VC/FA-SC61UC CUT ANTENNAS
FA-SC61VC: 136 ~ 174 MHz
FA-SC61UC: 380 ~ 520 MHz
• FA-SC62V/FA-SC63V HIGH GAIN ANTENNAS
FA-SC62V: 150 ~ 160 MHz
FA-SC63V: 155 ~ 165 MHz
D OTHERS
• AD-118 ACC ADAPTER
Connects to an accessory which uses a HIROSE plug.
See the instruction sheet of the AD-118 for details of the
recommended accessories.
CAUTION: The AD-118 is not waterproof. When it
is connected, NEVER expose the adapter and the
transceiver to rain, snow or any liquids.
• HM-184/HM-184H SPEAKER MICROPHONE
Rugged type speaker microphones.
The HM-184 and HM-184H meet IP67 requirements for
dust-tight and waterproof protection.
• MB-130 VEHICLE CHARGER BRACKET
Vehicle mounting bracket for the BC-160 battery charger
• VS-4MC PTT SWITCH CABLE
+ HS-94/HS-95/HS-97 HEADSET
VS-4MC: Used to connect a headset to a transceiver.
HS-94: Ear-hook type
HS-95: Neck-arm type
HS-97: Throat microphone
L The VS-4MC meets IP54 requirements for dust-protection
and splash resistance.
Some options may not be available in some countries.
Ask your dealer for details.
Loading...