ICIRCUIT ICP01 USB PIC PROGRAMMER

ICP01 – USB PIC PROGRAMMER

USB PIC

PROGRAMMER

ICP01 – USB PIC PROGRAMMER

1. Introduction and overview

iCP01 offers unprecedented level of performance, reliability and scalability for PIC programmer solution with low cost. By the same time, it allows users to program their hex code into the wellknown Flash PIC MCU by using commonplace USB connection method. The features of iCP01 are listed as followings.

 Low cost, small size , high performance and user friendly device  Every part is assembled perfectly and programmer is tested before submitting to users.  Used for programming the popular Flash PIC MCU, includes PIC10F, PIC12F, PIC16F and

PIC18F family

 No external power supply is required  Compatible with Microchip’s PICkit 2 and MPLAB IDE  USB plug and play function  Excellent flexibility that allows using in both PC desktop and laptop.  High speed programming  Allows to use in both commercial and free interface software

Dimension:

 Dimension: 6.8cm X 2.5cm X 0.9cm, easy to carry and store  ICSP wire length: ~ 30cm  Standard 2.54mm Pin Socket for ICSP connection

1.1 Programmer layout

ICP01 – USB PIC PROGRAMMER

5. ICSPCLK/PGC

4. ICSPDAT/PGD

3. GND

2. 5V

1. MCLR

2. 5V

3. GND

4. ICSPDAT/PGD

5. ICSPCLK/PGC

iCP01 – Programmer ICSP Connector

2. Programmer Connection

2.1 Programming Connector PIN

2.2 On-Board ICSP Connection

ICP01 – USB PIC PROGRAMMER

3. Hardware Installation

This section shows how to connect iCP01 to PIC MCU. Please download the driver from the link below for the first time usage.

http://www.piccircuit.com/ins/PICkit2v2.61.zip

3.1 Direct connection between iCP01 and Development/Application Board

1. Connect the USB connection on iCP01 to

laptop or desktop.

2. Connect the output port on iCP01 to

target/application board

 Target/application board is required an

external power supply on it due to the

USB port from PC/laptop can’t supply

large power usage.

3.2 Connection between iCP01 and iCP03

To augment the efficient of iCP01, Icircuit Technologies also provides users a extension circuit named iCP03 (Multi PIC Adapter) which allows users to program the MCU chips with iCP01 directly. This section shows user how to insert the PIC MCU chip onto the iCP03.

ICP01 – USB PIC PROGRAMMER

4. Software installation

For programming a microprocessor, programmer software is needed to transmit the machine code from PC to it. Here, our iCP01 can be used with the PICkit2 which is freeware provided by MICROCHIP and this software always been updated for better usage. So the following section will explain about how to install the PICkit 2 software into user computer.

4.1 Open the setup file

Select “Setup.exe” to install the PICkit software (Please download it from this link)

http://www.piccircuit.com/ins/PICkit2v2.61.zip

4.2 After the installation, update with the latest PIC devices list

Apply the patch PK2DeviceFile.dat at: (Replace it) C:\Program Files\Microchip\PICkit 2 v2\PK2DeviceFile.dat (or) C:\Program Files (x86)\Microchip\PICkit 2 v2\PK2DeviceFile.dat

ICP01 – USB PIC PROGRAMMER

4.3 Execute the PICkit setup process

Follow the guideline below to install the PICkit software.

i. Select [Next]

ii. Change the installation destination

if necessary and click [Next]

iv. Click [I Agree] and select [Next] to start

installation procedure

v. Wait for installation process to finish.

iii. Click [Next] to confirm installation

procedure

vi. Select [Close] to end up after the

installation is complete.

ICP01 – USB PIC PROGRAMMER

5. Programming MCU with PICkit 2

After previous hardware and software installation, user now is able to use iCP01 to program their PIC microcontroller. The following section illustrates the guidance steps for programming the MCU with PICkit programmer software.

5.1 First at all, ensure iCP01 is connected to PC desktop/laptop  Ensure power supply of target/application board is on if user is using the

target/application board.

5.2 Open PICkit 2 program by choosing the PICkit icon as below on desktop.

5.3 Here, the description of each part for PICkit program are shown as below.

5.4 If the program status box shows “PICkit 2 not found, …”, then user is required to

replug the iCP01 and to click [Tools] -> [Check Communication] for connecting the iCP01 with PICkit software.

ICP01 – USB PIC PROGRAMMER

5.5 Now user can started either to download the machine code (hex file) into the MCU or

to upload the hex code from MCU into PC after previous steps.

Download the hex code

i. Select [File] -> [Import Hex] and

choose the needed hex file to download.

Upload the hex code

i. First, user clicks the [Read] button to

upload the source code in MCU into PICkit program.

ii. After selected hex file, user can

see the imported message at program status.

iii. Then, user can click [Write] to

download the source code into MCU and

iv. Finally complete message is

shown at the end.

ii. Then user can see the done message at

program status.

iii. Now user can save the hex code into PC

by selecting [File] -> [Export Hex].

ICP01 – USB PIC PROGRAMMER

For further information or technical assistance please contact: Web:

http://www.piccircuit.com

Email:

support@piccircuit.com

Disclaimer

iCircuit Technologies has an on going policy to improve the performance and reliability of their products; we therefore reserve the right to make changes without notice. The information contained in this data sheet is believed to be accurate however we do not assume any responsibility for errors or any liability arising from the application or use of any product or circuit described herein. This data sheet neither states nor implies warranty of any kind, including fitness for any particular application.

Any liability from defect or malfunction is limited to the replacement of product ONLY, and does not include labour or other incurred corrective expenses.

Using or continuing to use these devices hereby binds the user to these terms.

CONTACT INFORMATION

ICIRCUIT ICP01 USB PIC PROGRAMMER

Specifications and Main Features

Frequently Asked Questions

User Manual