where the electric voltage for its power supply is not available.
●
This product is designed for indoor installation.
Please be sure to install it indoors.
●
The external appearance, design, color, and components
of this machine may be changed without prior notice.
Contents
1. Safety Cautions3
Power supply related items
Installation related items
2. Part names
3. Installation specifications
Gravity Drain Pipe Model
Drain Pump Model
4. What to check prior to installation
5. Installation of the Product
6. Specific Features
7. Guide to Operating the Ice Maker
8. Washing the Ice Maker
9. Maintenance of the Ice Maker
4
5
6
7~8
9
10
11
12~13
14
15~16
17~20
21
10. Specifications
11. Troubleshooting guide
2
2
22
23
1. Safety Cautions
To prevent any safety-related accident and to ensure convenient usage of this product
with better understanding, cautions and warnings are accompanied by symbols and figures.
Make sure you understand the symbols and figures below before proceeding.
Danger
Warning
Caution
Using the product without taking careful note of this symbol may cause
death or serious injury to the user or fire.
Using the product without taking careful note of this symbol may cause
death or serious injury to the user or fire.
Using the product without taking careful note of this symbol may cause
injury to the user or property damage.
※ Injury includes wound or burn that requires long-term outpatient treatment.
※ Property damage means damage or loss of one's house or furniture.
※ Label: If the caution label is corrupted, or its text is not legible enough,
contact the customer service center or the store
where the product was purchased.
Each figure has the following meaning:
Must be followed
General prohibition
Must be grounded
Disassembly not allowed
Contact not allowed
The power cord must be disconnected from the outlet.
Danger of electric shock
3
■ Power supply related items ■
Oh! NO
Avoid putting any object on
the power cord and make
sure that the cord does not
get tangled or tied.
It may cause fire or electric
shock.
Do not touch any electrical
component or the power
cord with wet hands.
It may cause electric shock.
Do not pull the power cord.
Failure to do so may cause
electric shock or fire.
Do not touch the power
cord with wet hands.
Failure to do so may cause
electric shock or fire.
Oh! NO
Stop using the product
if the power cord
is damaged.
It may cause fire or
electric shock.
Do not alter the power
cord or arbitrarily modify
it to connect to an
unauthorized power source.
Failure to do so may cause
electric shock or fire.
Do not plug too many
appliances into one
outlet; only one
appliance per outlet is
recommended.
Otherwise, there is danger
of fire.
To replace or repair
the power cord, contact
a professional technician
or our customer service
center.
Close the water supply valve
and unplug the product
if it is not to be used for
an extended period of time.
It may cause electric shock
or fire.
Clear the pin of the power
plug of any substance
including water or dust.
4
Failure to do so may cause
fire or electric shock.
A/S
If water got inside the power
components, immediately
unplug the cord and
completely dry the product
before using it.
Failure to do so may cause
electric shock or fire.
If the power plug or cord
is damaged, do not try to
replace it arbitrarily; contact
the customer service center.
Failure to do so may cause
fire or electric shock.
■ Installation related items ■
THINNER
GAS
Keep away any heating
appliance from the power cord.
It may melt the coating of the
cord, causing fire or electric
shock.
Combustible gas or flammable
material (benzene, gasoline,
thinner, LP gas, etc.) must be
kept away from the product
GA
SOL
LIN
and should never be put on
the product.
It may explode or cause fire or
injury.
Do not apply excessive force or
shock to the product.
It may damage the product.
Make sure no water comes
into contact with any electric
part or inside the product.
If the product has been
immersed in water due to
causes such as flood, be sure
to contact the customer service
center. Otherwise, the product
may short circuit and cause fire
or electric shock.
Room temperature of
10~20℃
Temperature of supplied
water: lower than 10℃
Do not install the product
at a place where moisture
or dust gathers easily or
where rain or water spatters.
It may cause electric shock
or fire.
Do not install the product on
a tilted surface.
It may cause injury to the
user or damage to the
product.
The ice maker provides
optimal functionality at
room temperature of
10~20℃ and supplied
water temperature of lower
than 10℃.
It may damage the product.
Do not store or use
combustible gas or
flammable material near
the product.
It may cause electric shock
or fire.
Do not disassemble or
modify the product.
It may cause electric shock,
fire, or injury.
Contact a professional
service supplier to repair
the product.
Incomplete repair may
cause electric shock, fire,
or injury.
5
2. Part names
【 FRONT 】
Door handle
Top cover
Water tank
Door
Operation switch
Front panel
Bottom grill
【 BACK 】
Back cover
Water supply socket (Inlet)
Water drain socket(Outlet)
Power cord
6
3. Installation specifications
Space requirements for installation
When moving the ice maker, check whether the prepared
opening dimensions,electric power, and piping position are
correct.
Refer to the installation specifications and drawings shown
on pages 9 and 10.
Figures 4, 5, 6 and 7 show the entire dimensions of the product.
This product is a gravity drain pipe model that requires a
drain pipe to run from the exhaust hole at the back
of the product to appropriate drain pipe.
The optional drain pump to be installed an raised water
to a drainage point such as a neighboring sink.
Fig. 1 Front View
Refer to the specifications shown on pages 9 and 10.
Important Information :
a corner, the lever may be attached to a wall or the front side
of a cabinet, thereby limiting the opening of the door.
The bottom of the ice maker should be leveled.
When moving the product using a hand truck or dolly,
place the dolly at the side of the product and shut or fix
the door tightly to avoid possible opening during movement.
If the ice maker is installed at
Caution
Fig. 2 Side View
Fig. 3 Top View
The finished bottom should be protected with a suitable material
to avoid possible damage when moving the product
Requirements for power supply
230VAC, 50Hz, 15-amp circuit breaker and electric
power are required. A separate circuit is required
for grounding.
The power cord of the product should be inserted into
a suitable 3-prong groundingtype consent.
Important Information :
(GFCI) is not recommended because the operation
of the product may be stopped.
A Ground Fault Circuit Interrupter
Important Information : The provisions of the National
Electric Code as well as any local laws and instructions
should be observed when installing the product
.
Warning
Do not use extension codes or 2-prong adapters.
The product should necessarily be grounded.
Do not use the grounding terminal of the 3-prong grounding
plug with cutting.
7
Requirements for plumbing
Plan the arrangement of the water supply pipes.
Connect a 1/4" diameter copper cable with the tap water pipe.
Install a shutoff valve between the tap water pipe and the product so that the user
can operate the valve. Do not install the shutoff valve at the back of the product.
“Do not use a self-piercing valve. If the tap water has a high level of minerals,
a pipeline filter will be required.
The pressure of the tap water should be maintained at a level between 20psi (1.4bar)
and 80psi (5.5bar). The tap water and drain pipeline should be planned and prepared
at the place of installation. If an electric outlet is available just at the back of the ice
maker, installation may be easier. The electric power, tap water pipeline and drain pipeline
should satisfy all the provisions under the local laws and regulations. For the position
of the tap water, refer to the installation specifications and drawings on pages 7 and 8.
Important Information :
may be required to draw the product near for service. Therefore, do not install any material
at the front, upper or lower end of the product which may act as an obstacle
when drawing the product.
When preparing the bottom after installing the ice maker, place shims equivalent
to the thickness of the bottom under the product to keep the ice maker and bottom
horizontal. The lateral side should have at least 1/6" (4) of space for projection
of the screw head.
Installation of a slab :
a built-in drain pump. The drain pump model may raise the water up to about 8ft (2.4m)
in height. The more bent parts the pipeline has, the lower the raising height is.
The product is designed for use in a fixed condition but it
Draw up the water to the drain position using the model with
Installation in a narrow or underground place : A gravity drain model or drain
pump model may be used. If there is no space for drainage/sewage at the back
of the ice maker, the drain tube should be placed under the bottom.
Important Information :
laid out under the local laws and regulations.
Piping should be carried out in accordance with all the provisions
8
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.