Ice-O-Matic IOD150, IOD200 User Manual

e

SERVICE/INSTALLATION MANUAL

ICE ONLY DISPENSERS

MODELS-IOD150, IOD200 AND IOD250

Mile High Equipment
11100 East 45th Av
Denver, Colorado 80239

Part Number 9081305-01 Print Date 06/02

Introduction IOD150,IOD200,IOD250

To the owner or user: This product manual is a source of information about the installation, start up,
cleaning, maintenance and repair of the product.

The IOD150, IOD200 and IOD250 are ice only counter top dispensers designed to use 22 inch wide
and 30 inch wide respectfully Ice-O-Matic cubed ice machines as the source of ice.

The IOD ice dispenser is a machine that stores ice in an insulated, sanitary container: upon demand it
dispenses that ice into a cup or glass.

Table of Contents

Introduction Page 1

Specifications and Limitations Page 2

For The Installer Page 3

Installation Page 4

Water Glass Filler Kit Page 5-6

Initial Start Up Page 7

Gate Restrictor Plate Page 8

Cleaning And Sanitizing Page 9-10

Warranty Information Page 2

Keep this manual for future reference.

Ice-O-Matic
11100East 45
Denver Colorado 80239

Technical Assistance
1-800-423-3367

The IOD150, IOD200 and IOD250 Parts Manual is available separately, Part Number 9081306-01

th

Ave.

Page 1

Specifications and Limitations IOD150, IOD200, IOD250

Limitations:
Must meet the same limitations as the cuber installed on top of it:

50° F. air minimum
100° F. air maximum
Must be installed indoors.

Must allow at least 6-inch clearance at the rear and both sides when using an air-cooled
machine.
Must allow space for the utility connection at the back.
Must have a drain.

Options (Field Installed) (*Required)
*Thermostatic Bin Control Kit (22 Inch Ice Series) Part Number 1051134-01
*Thermostatic Bin Control Kit (30 Inch Ice Series) Part Number 1051020-02

Manual Water Glass Filler Kit Part Number KWGFID
*Ice Machine Adapters
*22 inch cuber Part Number KBT15022
*22 inch machine on a 30 inch dispenser Part Number KBT25022
*30 inch cuber Part Number KBT25030

Dispenser Specifications

Storage Basic Min. Circuit

Model Number
IOD150 150 115/60/1 Lever 3.0 15
IOD200 220 115/60/1 Lever 3.5 15
IOD250 250 115/60/1 Lever 3.5 15

Dimensions (Inches)

Model Number
IOD150 22 inches 30 inches 35 5/8 inches
IOD200 30 inches 30 inches 35 5/8 inches
IOD250 30 inches 30 inches 39 5/8 inches

Note: Counter top 4 inch legs are included with the dispenser

Ice-O-Matic ice machines are not designed for outdoor
installations.

Machine requires voltage indicated on rating nameplate. Failures
caused by improper voltage are not considered factory defects.
Extended periods of operation at temperatures exceeding limitations
constitutes misuse under the terms of the Ice-O-Matic Manufacture’s
Limited Warranty, resulting in a loss of warranty coverage.
Specifications and design are subject to change without notice.

The IOD150, IOD200 and IOD250 carry a 2-year Parts warranty
and a 1 year Labor Warranty.

These dispensers are designed to dispense cubed ice only.
Flaked ice will not work.

The dispenser will agitate for 4 seconds every (1) hour.

Capacity (lbs) Electrical Actuation Ampacity Max. Fuse Size

Width Depth Height (Excludes 4” Legs)

.

ice

Page 2

For The Installer IOD150, IOD200, IOD250

Equipment Description

The IOD150, IOD200 and IOD250 are counter top mounted ice only dispensers. These units are
designed to dispense cube ice only and have ice storage capacities of 150 lb.,220 lb. and 250 lb.
respectively.

Site Preparation

The site chosen for the dispenser must be capable of supporting the dispenser with a full bin of ice
plus all other loads being placed on the surface supporting the dispenser. If an ice machine is being
placed on the dispenser, the weight of the ice machine must be included in the calculations to
determine the support structure needed for the dispenser.

Allow sufficient clearance above the unit for removal of the cover and for pouring ice into the bin.

A 115 volt, 15 amp electric outlet needs to be located within 6 feet of the unit. The outlet must be

properly grounded and fused. No other electrical appliance should be on the circuit. ALL
ELECTRICAL WIRING MUST CONFORM TO NATIONAL AND LOCAL CODES

Do not place the dispenser next to heat sources such as ovens, heat ducts or in the warm air
discharge from adjacent equipment.

The unit must be located near a building drain. Drain lines must be properly vented and pitched to
ensure free flowing of wastewater to the drain.

These dispensers are designed to dispense cubed ice only. Do not use flaked, crushed or
compressed ice forms.

If an Ice-O-Matic ice machine is to be placed on top of the dispenser, an adapter will be required.
Ice Machine Adapter 22 inch cuber Part Number KBT15022
Ice Machine Adapter 22 inch cuber on 30 wide dispenser Part Number KBT25022
Ice Machine Adapter 30 inch cuber Part Number KBT25030

This ice dispenser has been specifically designed to provide protection against personal injury and
eliminates contamination of ice. To ensure continued protection and sanitation, observe the following:

·ALWAYS: disconnect power to the dispenser before servicing or cleaning.

·NEVER: place hands inside of hopper or grate area without disconnecting power to the dispenser.

·Agitator rotation occurs automatically when dispenser is energized.

·ALWAYS: be sure the removable lid is properly installed to prevent unauthorized access to the

hopper interior and possible contamination of the ice.

·ALWAYS: be sure the upper and lower front panels are securely fastened.

·ALWAYS: keep area around the dispenser clean of ice cubes.

·CAUTION: Dispenser cannot be used with crushed or flaked ice.

Use of bagged ice, which has frozen into chunks, can void warranty.

The dispenser agitator is not designed to be an ice crusher. Use of large chunks of ice which “jam
up” inside the hopper will cause failure of the agitator motor and damage to the hopper. If bagged ice
is used, it must be carefully and completely broken into small, cubed size pieces before filling into the
dispense hopper.

Page 3