Ice-O-Matic ICEU300HA, ICEU226FW, ICEU220HW, ICE1506HR, ICE1506FR Installation Manual

Installation, Start-Up and Maintenance Manual

ICE SERIES CUBERS

ICE0250 through ICE2100 Series*

ICEU150, ICEU220 and ICEU300 Undercounter Series*

ICE0320 and ICE0520 22 Inch Series*

*INCLUDES 230/50/1 VOLT UNITS

Ice-O-Matic
11100 East 45th Ave
Denver, Colorado 80239
Part Number 9081264-01 Date 11/08

*

ICE Series Introduction

How To Use This Manual Ice-O-Matic provides this manual as an aid to the service technician in installation and maintenance of the ICE

Series (electro-mechanical) cube ice machines. Do not attempt to perform installation, start-up or maintenance

unless you have read and fully understand this manual.
If at any time you encounter conditions that are not addressed in this manual, call, E-mail or write the Ice-O-Matic

Service Department:
Ice-O-Matic

11100 E. 45
Denver, Co. 80239
Attn: Technical Service Department
E-Mail: [e-mail]

Telephone Numbers Any Service communication must include:
800-423-3367 All Departments • Model Number
888-349-4423 Technical Assistance Only (After Hours Only) • Serial number

• A detailed explanation of the problem

Keep this manual for future reference.

The ICE Series Service Parts Manuals are available separately.

Ice-O-Matic icemakers and dispensers are not approved for outdoor installation.
WARNING

repairs are performed on the ice machine and related equipment.
CAUTION:

machine and related equipment.

The following Ice-O-Matic models are ENERGY STAR qualified.

Self-Contained Cube Ice Makers:

ICEU150HA ICEU150FA
ICEU220HA ICEU220FA
ICEU300HA ICEU300FA

Modular Cube Ice Makers:

ICE0400FA ICE0400HA
ICE0400FT ICE0400HT
ICE0520FA ICE0520HA
ICE606HR ICE606FR
ICE0806HR ICE0806FR
ICE1007HR ICE1007FR
ICE1406HA ICE1406FA
ICE1407HA ICE1407FA
ICE1506HR ICE1506FR

Rebates or incentives may be available through local utility companies on ENERGY STAR qualified equipment.

th

Ave.

: Always disconnect electrical power and shut off water supply whenever maintenance or

Always wear protective eyewear whenever maintenance or repairs are performed on the ice

Page i

ICE Series Table of Contents

Introduction Page i
Table of Contents Page ii
Freight Claim Procedure Page iii
Warranty Page iv
Model Number and Serial Number Format Page 1
Installation Guidelines Page 2
Remote Condenser Guidelines Page 4
Electrical and Plumbing Requirements Page 6
How the Machine Works Page 13
Start-Up Procedure Page 14
General Maintenance Page 16
Cleaning Procedure Page 17
Cabinet Care Page 18
Winterizing Procedure Page 19
Maintenance Record Page 20

Page ii

ICE Series Freight Claim Procedure

Freight Claims Important!
Inspect Promptly

This merchandise has been carefully inspected and packed in accordance with the carrier’s packing specifications.
Responsibility for safe delivery has been assumed by the carrier. If loss or damage occurs, you as the consignee must
file a claim with the carrier and hold the container for carrier’s inspection.

Visible Loss or Damage

Any external evidence of loss or damage must be fully described and noted on your freight bill or express receipt and
signed by the carrier’s agent. The claim should be filed on a form available from the carrier.

Concealed Loss or Damage

If loss or damage does not appear until merchandise has been unpacked, make a written requ est for inspection by the
carrier within 15 days of the delivery date. Then file a claim on a form from the carrier.

File Claim Without Delay
Do Not Return Damaged Merchandise to Ice-O-Matic

Page iii

ICE Series Warranty

Ice-O-Matic

Domestic & International Limited Warranty

Mile High Equipment LLC (the “Company”) warrants Ice-O-Matic brand ice machines, ice dispensers, remote condensers, water filters, and ice
storage bins to the end customer against defects in material and factory workmanship for the following:

• Cube ice machines,”GEM” model compressed ice
machines ,” MFI” model flake ice machines and remote
condensers. - Thirty-six (36) months parts and labor

• “EF” and “EMF” model flake ice machines - Twenty-four
(24) months parts and labor

• CD model dispensers - Thirty-six (36) months parts and
labor

An additional twenty-four (24) month warranty on parts (excluding labor) will be extended to all cube ice machine evaporator plates and
compressors, “GEM” model compressed ice machine compressors, and “MFI” model flake ice machine compressors from the date of original
installation. An additional thirty-six (36) month warranty on parts (excluding labor) will be extended to all “EF” and “EMF” model flake ice machine
compressors from the date of original installation. The company will replace EXW (Incoterms 2000) the Company plant or, EXW (Incoterms 2000)
the Company-authorized distributor, without cost to the Customer, that part of any such machine that becomes defective. In the event that the
Warranty Registration Card indicating the installation date has not been returned to Ice-O-Matic, the warranty period will begin on the date of
shipment from the Company. Irrespective of the actual installation date, the product will be warranted for a maximum of seventy-two (72) months
from date of shipment from the Company.

ICE-model cube ice machines which are registered in the Water Filter Extended Warranty Program will receive a total of eighty-four (84) months
parts and labor coverage on the evaporator plate from the date of original installation. Water filters must be installed at the time of installation and
registered with the Company at that time. Water filter cartridges must be changed every six (6) months and that change reported to the Company to
maintain the extended evaporator warranty.

No replacement will be made for any part or assembly which (I) has been subject to an alteration or accident; (II) was used in any way which, in the
Company’s opinion, adversely affects the machine’s performance; (III) is from a machine on which the serial number has been altered or removed;
or, (IV) uses any replacement part not authorized by the Company. This warranty does not apply to destruction or d amage caused by unauthori zed
service, using other than Ice-O-Matic authorized replacements, risks of transportation, damage resulting from adverse environmental or water
conditions, accidents, misuse, abuse, improper drainage, interruption in the electrical or water supply, charges related to the replacement of non­defective parts or components, damage by fire, flood, or acts of God.

This warranty is valid only when installation, service, and preventive maintenance are performed by a Company-authorized distributor, a Company­authorized service agency, or a Company Regional Manager. The Company reserves the right to refuse claims made for ice machines or bins used
in more than one location. This Limited Warranty does not cover ice bills, normal maintenance, after-install adjustments, and cleaning.

Limitation of Warranty

This warranty is valid only for products produced and sh ipped from the Company after January, 2007. A product produced or installed
before that date shall be covered by the Limited Warranty in effect at the date of its shipment . The liability of the Company for breach of
this warranty shall, in any case, be limited to the cost of a new part to replace any part, which proves to be defective. The Company
makes no representations or warranties of any character as to accessories or auxiliary equipment n ot manufactured by the Company.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER. MILE HIGH
EQUIPMENT SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATI ON TO THE LENGTH OF THIS
WARRANTY.

Filing a Claim
All claims for reimbursement must be received at the factory within 90 days from date of ser vice
this time period will be void. The model, the serial number and, if necessary, proof of installation, must be included in the claim. Claims for labor
to replace defective parts must be included with the part claim to receive consideration. Payment on claims for labor will be limited to the published
labor time allowance hours in effect at the time of repair. The Company may elec t to require the return of components to validate a claim. Any
defective part returned must be shipped to the Company or the Company-authorized distributor, transportation charges pre-paid, and properly
sealed and tagged. The Company does not assume any responsibility for any expenses incurred in the field incidental to the repair of equipment
covered by this warranty. The decision of the Company with respect to repair or replacement of a part shall be final. No person is authorized to give
any other warranties or to assume any other liability on the Company’s behalf unless done in writing by an officer of the Company.

GOVERNING LAW

This Limited Warranty shall be governed by the laws of the state of Delaware, U.S.A., excluding their conflicts of law principles. The United Nations
Convention on Contracts for the International Sale of Goods is hereby excluded in its entirety from application to this Limited Warranty.

Mile High Equipment LLC, 11100 East 45

Parts and Labor

• Ice storage bins -Twenty-four (24) month parts and labor

• IOD model dispensers - Twenty-four (24) months parts, Twelve (12) months

labor

• Water filter systems - Twelve (12) months parts and labor (not including filter
cartridges)

to be eligible for credit. All claims outside

th

Avenue, Denver, Colorado 80239 [phone]

January 2007

Page iv

ICE Series Model and Serial Number Format Model and Serial Number Format

Note: Sample of Serial Number Data Plate

The serial number format and machine specifics are detailed on the
data plate.

ICE 040 0 H A 2

Design Level

Condenser Type: A=Air, W=Water, R=Remote

Cube Size: H=Half, F=Full

Voltage: 0=115V, 6=230V/60Hz. 5=240V/50Hz.

Approximate Production in 24 hours @70°FAir/50°FWater
Series: Environmental Cuber (Uses HFC Refrigerant)
This format is 14 characters long and begins with a date code

followed by the Ice-O-Matic identifier, and then a sequential
number. This is an entirely numerical serial number.

The serial number will look like the example.

1280 010077

0407

010077 is the serial identifier.

1280 is the identifier. (Ice-O-Matic)
0407 is the date code, in YYMM format. (2004 July)
Large data plate will be placed on the back of the unit.

Small data plate will be placed by the service valves

The date code will change monthly and yearly to reflect the date of
manufacture.

.

Page 1

ICE Series Installation Guidelines Installation Guidelines

For proper operation of the Ice-O-Matic ice machine, the following installation guidelines mu st be followed. Failure to
do so may result in loss of production capacity, premature part failures, and may void all warranties.

Reference the installation parameters prior to installing the machine:

Ambient Operating Temperatures

Minimum Operating Temperature: 50°F (10°C)
Maximum Operating Temperature 100°F (38°C), 110°F (43°C) on 50 Hz. Models.

Note: Ice-O-Matic icemakers and dispensers are not approved for outdoor installation.
Incoming Water Supply (See Electrical and Plumbing Diagrams for line sizing)

Minimum incoming water temperature: 40°F (4.5°C)
Maximum incoming water temperature: 100°F (38°C)
Minimum incoming water pressure: 20 psi (1.4 bar)
Maximum incoming water pressure: 60 psi (4.1 bar)

Note: If water pressure exceeds 60 psi (4.1 bar), a water pressure regulator must be installed.
Drains

All drain lines must be installed per local codes. Flexible tubing is not recommended. Route bin drain, purge drain and
water condenser drain individually to a floor drain. The use of condensate pumps for draining water is not
recommended by Ice-O-Matic. Ice-O-Matic assumes no responsibility for improperly installed equipment.

Note: The purge drain fitting is plastic; DO NOT apply heat to the purge drain area; DO NOT overtighten.
Water Filtration

A water filter system should be installed with the ice machine.

Clearance Requirements

Self-contained air cooled ice machines must have a minimum of 6 inches (15cm) of clearance at the rear, top, and
sides of the ice machine for proper air circulation.

Stacking

If the ice machines are to be stacked, refer to the instructions in the stacking kit. Ice-O-Matic does not endorse
stacking air-cooled ice machines.

Dispenser Application

A thermostatic bin control kit should be installed if the ICE Series ice machine is placed on a dispenser. A bin top may
or may not be required. (Exception is the CD400 Series Dispenser)

Electrical Specifications

Refer to the serial plate at the rear of the ice machine to make sure proper voltage and circuit breaker size have bee n
supplied. Make sure the machine is on a dedicated circuit. European installations require that the electrical supply
fixed wiring must be provided with a disconnect means having a separation of at least 3mm in all poles. The ice
machines are provided without
connected.

The 115 volt Undercounter series ice makers are supplied with an electrical cord, all other ice makers will
need to be installed and wired per local electrical codes.

Caution: Electrical connection must be made or a cord installed by a qualified electrician
electrical fire.

Adjustments

Level the machine within 1/8 inch in all directions.
Check the bin control for proper adjustment.
Check the water in the water trough for proper level.
Check the ice bridge for proper thickness.
Check the water regulating valve adjustment if water cooled.

an electrical cord set and are designed and agency approved to be permanently

or there is danger of an

Page 2