ICC ICCMSWMP12, ICCMSWMP26 Installation
Detail B
DOOR HINGES
ADJUSTABLE DEPTH
FRONT DOOR HINGE
CAUTION!
Do not overload the cabinet. Cabinet can support up to 150 lbs. of equipment when properly installed using all mounting holes.
Make sure wall has a structural load capacity that will support the weight of the cabinet fully loaded equipment.
Do not attempt to lift the cabinet alone.
Before installation, locate where the cabinet is to be installed; concrete walls, plywood and wooden studs are recommended.
Step 1: Use a level to mark locations for mounting screws as
shown above. Templates and screws are not provided.
ICCMSWMC12/ICCMSWMP12: Requires four (4) ¼-10 X 2 Lag Screws
ICCMSWMC26/ICCMSWMP26: Requires eight (8) ¼-10 X 2 Lag screws
Step 2: Drill screws into marked locations without fully tightening
them. Leave at least a .5” gap between screws and wall.
Note: Make sure the screws you are using fit the screws slot shown
in Detail A.
Step 3: Place the Wall Mount Cabinet onto the pre-drilled screws,
then tighten all screws. Screws and screw slots should look like
Detail B when fully tighten.
NOTE: To adjust the depth of the rail, lightly untighten the screw,
adjust to the desired depth and then tighten the screw.
Wall Mount Cabinet, 12 & 26 RMS
I N S T A L L A T I O N I N S T R U C T I O N S
©Copyright 2014, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved MSR-0534-RevB
888-ASK-4ICC csr@icc.com icc.com
PART NUMBER
DESCRIPTION
ICCMSWMC12
22”W x 24”H x 26”D, 12 RMS
ICCMSWMP12
22”W x 24”H x 26”D, 12 RMS, Plexiglass Door
ICCMSWMC26
22”W x 48”H x 26”D, 26 RMS
ICCMSWMP26
22”W x 48”H x 26”D, 26 RMS, Plexiglass Door
Single Horizontal Finger Ducts
ICCMSCMA41 1.75”H x 3.19”D, 1 RMS
ICCMSCMA42 3.50”H x 3.23”D, 2 RMS
• For front cable management
• Durable steel base with plastic fingers
• Includes slide-on cover
Metal Ring Panels
ICCMSCMPK1 Panel with cover, 1
RMS
ICCMSCMPK2 Panel with cover, 2
RMS
• For horizontal cable routing
CAT 6 Patch Panels
ICMPP02460 24-Port, 8P8C, 1 RMS
ICMPP04860 48-Port, 8P8C, 2 RMS
• Exceeds ANSI/TIA-568 standards
• Rear 110-Type IDC termination
Cable Management Rings
ICCMSCMPR5 1.25” Vertical Ring
ICCMSCMPR7 3” Universal Ring
ICCMSCMPT1 1.7” Single Ring
ICCMSCMPT2 3” Single Ring
• Provides flexibility for front or back
cable management with a neat and clean
appearance
Wall Mount Cabinet, 12 & 26 RMS
I N S T A L L A T I O N I N S T R U C T I O N S
F E A T U R E S A N D B E N E F I T S
Vented panels help circulate air
Wall mountable for left or right orientation
Cable knockouts on top and bottom: (4) 3.0” and (4) 0.88”
Mounting rails for equipment are adjustable
Rails accommodate equipment with 19” widths
Complies with EIA/ECA-310-E standard
Front door is hinged, removable, reversible and lockable
Rear panel is hinged and lockable
O P T I O N A L A C C E S S O R I E S
©Copyright 2014, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved MSR-0534-RevB
888-ASK-4ICC csr@icc.com icc.com
Loading...