ICC ICCMSR1984 User Manual
19” 2-Post Distribution Rack
ICC’s 2-post racks are designed to be lightweight, sturdy, and easy to install. These high quality, black powder coated aluminum racks will
support most EIA 19” rack mountable network devices and hardware such as servers, switches, PBX systems, and other equipments.
PremiumProducts • ProvenPerformance • CompetitivePrices
INSTALLATION INSTRUCTIONS
CUSTOMER CARE / TECHNICAL SUPPORT • CSR@ICC.COM / 888-275-4422 (ASK-4-ICC) • WWW.ICC.COM
© Copyright 2009, ICC. ICC and ICC logo are registered trade name and trademark. All r ights reserved. MSR-0265-RevD
1. Lay the vertical mounting
rails on a flat surface with
the open channels facing
inward.
2. Place one top angle across the
top end of the vertical mounting
rails. Install two 3/8-16 bolts, lock
washers, and nuts as illustrated.
Hand tighten only!
3. Place one base angle across the
bottom end of the vertical mounting
rails. Install four 3/8-16 bolts, lock
washers, and nuts as illustrated
Hand tighten only!
4. Turn the assembly over and repeat steps
2 & 3 for the other side.
5. Stand the assembly up to check for
squareness. Make sure the base is level
and will rest on a flat surface.
6. Tighten the bolts and torque to
approximately 23-30 lb-ft.
7. Anchor the distribution rack assembly to
rigid flooring utilizing the four holes on the
base angles.
Note: Tapped holes are 12-24 threads.
Products to be mounted to these
rack assemblies should have their
own 12-24 mounting screw. ICC
provides additional screws in bags
of 30 pieces as item number
ICACSS01BK.
Item No. Height RMU* RMU Markings
ICCMSR1948 4 feet 24 RMS Yes
ICCMSR1972 6 feet 38 RMS Yes
ICCMSR1984 7 feet 45 RMS Yes
*Rack Mount Units
Hardware Included
• (2) Top angles - Aluminum
• (2) Base angles - Aluminum
• (2) Vertical mounting rails - Aluminum
• (12) 3/8-16 bolts, black oxide
• (12) lock washers, black oxide
• (12) 3/8-16 nuts, black oxide
Certification
EIA 310-D Compliant
Racks & Cable Management
New Feature!
ICC’s Rack Mount Unit
(RMU) numbered markings
provide consistent vertical
alignment and spacing of equipment
attachment points for panels, shelves, cable
management and associated equipment.
RMU numbered markings begin from the
bottom to the top of rails for consistent
positioning regardless of rack height.
Horizontal Metal Cable Management Panel
ICCMSCMP31 Horizontal & 2 Side Vertical Rings, 1 Rack Mount Space
ICCMSCMP32 Horizontal & 4 Side Vertical Rings, 2 Rack Mount Spaces
ICCMSCMP51 Horizontal Rings, 1 Rack Mount Space
ICCMSCMP52 Horizontal Rings, 2 Rack Mount Spaces
Horizontal Finger Duct Panel
ICCMSCMA41 Single-Sided Front Ducts, 1 Rack Mount Space
ICCMSCMA42 Single-Sided Front Ducts, 2 Rack Mount Spaces
ICCMSCMA61 Double-Sided Dual Ducts, 1 Rack Mount Space
ICCMSCMA62 Double-Sided Dual Ducts, 2 Rack Mount Spaces
RELATED PRODUCTS
Horizontal Cable Management Panel
ICCMSCMA31 Horizontal & 2 Vertical Rings, 1 Rack Mount Space
ICCMSCMA32 Horizontal & 2 Vertical Rings, 1 Rack Mount Space
ICCMSCMA51 Horizontal Rings, 1 Rack Mount Space
ICCMSCMA52 3.5” H x 19” W, 2 Rack Mount Spaces 5 horizontal rings
ICCMSCMC01 Panel cover, 1 Rack Mount Space
ICCMSCMC02 Panel cover, 2 Rack Mount Spaces
Rack Floor Wall Mount Kit, Concrete
ICCMSRFLKT Hardware, Rack, Installation For Concrete Floors and Walls.
Vertical Finger Duct Panels & Vertical Cable Management Channel
ICCMSCMA81 78” ht., 4”x5” slotted front ducts, Side mount design
ICCMSCMA82 78” ht., 4”x5” slotted front and rear ducts, Center mount design
ICCMSCMA83 78” ht., 4”x5” slotted front and rear ducts, Side mount design
ICCMSCC6BK 6.5’ ht., Cable channel, vertical, black
ICCMSCMA81
ICCMSCMA82
ICCMSCC6BK
ICCMSCMA83
10” Deep Single Rack Shelf
ICCMSRSF10
2 rack mount spaces
Note: For use with 19” distribution and cable management racks
15” Deep Single Rack Shelf
ICCMSRSF15
3 rack mount spaces
Note: For use with 19” distribution and cable management racks
20” Deep Double Rack Shelf
ICCMSRDS20
2 rack mount spaces
Note: For use with 19” distribution racks only
30” Deep Double Rack Shelf
ICCMSRDS30
3 rack mount spaces
Note: For use with 19” distribution racks only
10” Deep Vented Rack Shelf
ICCMSRSV10
2 rack mount spaces
Note: For use with 19” distribution and cable management racks
15” Deep Vented Rack Shelf
ICCMSRSV15
3 rack mount spaces
Note: For use with 19” distribution and cable management racks
20” Deep Vented Rack Shelf
ICCMSRDV20
2 rack mount spaces
Note: For use with 19” distribution racks only
30” Deep Vented Rack Shelf
ICCMSRDV30
3 rack mount spaces
Note: For use with 19” distribution racks only
Loading...