iCanTek iCanView 222, iCanView 222W User Manual

iCanView222 User’s Guide

Rev1.0(Mar. 2008)

iCanView222 User’s Guide

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into and outlet on a circuit different from that to which

the receiver is connected

z Consult the dealer or an experienced radio/TV technician for help.

If you would like to use the iCanView222 for security, monitoring, please check the legal regulations within the country.

Use only the power adapter provided with the iCanView22 2.

Do not disassemble iCanView222. You will be excluded from After Service when disassembled.

Be careful not to cause any physical damage by dropping or throwing the iCanView222. Especially keep the device out of reach from children.

Directions

iCanView222 is designed for indoor use only. When using iCanView222 outdoors or in an environment that exceeds the limited range, you must separately use a water-resistant case.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Any changes or modifications in construction of this device which are not explicitly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Caution

This appliance and its antenna must not be co-located or operating in conju nction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements.

Revision History

Date Rev No Description

2008-03-7 1.0 Creation of the document

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

1. Introduction ................................................................................................................. 6

Table of Contents

1.1. Overview .......................................................................................................................... 6

1.2. Features of iCanView222 ............................................................................................... 6

1.3. Applications of iCanView222 ......................................................................................... 7

1.4. Selectable options and ordering information .............................................................. 7

2. Product Description .................................................................................................... 9

2.1. Contents .......................................................................................................................... 9

2.2. Preview ............................................................................................................................ 9

2.3. Physical description ...................................................................................................... 10

2.4. PC Requirements .......................................................................................................... 12

2.5 Quick Installation Guide ................................................................................................ 13

3. Connecting iCanView222 to Network ..................................................................... 17

3.1. Connecting to LAN ........................................................................................................ 17

3.2. Connecting to xDSL/Cable Modem ............................................................................. 18

4. IP-Installer ................................................................................................................. 20

4.1. Main window of IP-Installer ........................................................................................ 20

5. Configuring iCanView222 in Administrative Mode ................................................ 22

5.1. Log On ............................................................................................................................ 22

5.2. Basic Setup .................................................................................................................... 24

5.3. Network Configuration ................................................................................................. 26

5.4. Wireless Configuration ................................................................................................. 31

5.5. CCD Adjustment ........................................................................................................... 33

5.6. User Admin & Time Setup ........................................................................................... 36

5.7. Sensor & Capture Setup .............................................................................................. 39

5.8. Alarm Device Setup ...................................................................................................... 41

5.9. Motion Region Setup .................................................................................................... 43

5.10. Encryption Set up ....................................................................................................... 45

5.11. Upgrade & Reset ......................................................................................................... 47

5.13. Status Report .............................................................................................................. 49

6. Tips for using iCanView222 ..................................................................................... 50

6.1. ALARM-IN and ALARM-OUT ......................................................................................... 50

6.2. Trouble Shooting ........................................................................................................... 53

6.3. Web Viewer .................................................................................................................... 54

6.4. How to Upgrade the iCanView222 ............................................................................. 57

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Appendix. On Site Installation ..................................................................................... 58

A.1. Ceiling or Wall Mounting ................................... 오류! 책갈피가 정의되어 있지 않습니다.

A.2. Recessed Ceiling Mounting (mD112 recessed ceiling mount kit required)오류! 책갈

피가 정의되어 있지 않습니다.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

1. Introduction

1.1. Overview

The iCanView222 is a state-of-the-art network camera which transmits synchronized video and audio data in real time with D1 resolution at full frame rate. This is possible through MPEG4 CODEC technology, which provides high quality video with highly compressed data streams. The iCanView222 can be connected, controlled and monitored from a remote location through an IP connection over internet or intranet. Unlike CCTV or DVR, the iCanView222 is easy to install and owner will experience cost and space savings in the installation owing to the state of the art technologies embedded in the system. Based on Embedded Software Solution (Embedded Web Server, Embedded Streaming Server, Network Protocol), the iCanView222 ensures unprecedented performance and stability to be an ideal network camera solution for system integration solutions. To facilitate single cable installation, iCanView222 are offered with standard PoE option (IEEE

802.3af). Low height design together with optional recessed mounting accessories will ensure the iCanView222 to be the best choice among the competing mini dome IP cameras.

1.2. Features of iCanView222

y 1 channel synchronized real time Video/Audio streaming

MPEG-4 video, ADPCM audio.

y Bi-directional audio communication

Real time audio communication between iCanView222 and Client PC

y The viewer assisted recording and playback function s. y 1 Alarm sensor input/1 relay output y Motion detection – Up to 3 motion detection zones

Arbitrary shape motion detection zone

Motion detection can initiate video recording, which is sent to the user through F TP and/or E-mail.

y Resolution

- NTSC : 720x480, 352x240, 176x144.

- PAL/SECAM : 720x576, 352x288, 176x144 y Remote administration control Entire operational parameter set up, Software upgrade

y Embedded WiFi interface (iCanVeiw222W only) – IEEE 802.11b/g y Standard PoE (IEEE 802.3af) for single cable wiring of the network and power application. y Interior friendly design

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Low height, Recessed ceiling mount option Flush mounting.

1.3. Applications of iCanView222

y Security surveillance (buildings, stores, manufacturing facilities, parking lot s, banks, government

facilities, military, etc.)

y Real time Internet broadcasting y Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.) y Teleconference (Bi-directional audio conference) y Remote Learning y Weather and environmental observation

1.4. Selectable options and ordering information

For maximizing the application area, iCanView222 can be offered with varieties of options. These

options include various camera modules, lenses or network interface options. Refer to the following conventions for the selection of the options and model names.

z Naming convention

iCanView222

- WPMT

Basic model Options

Basic model

Basic Model Description Misc

iCanView222 270K Sony CCD, Fixed Lens

iCanView222+ 410K CCD, 480 TV lines, Varifocal

iCanView222++ 410K CCD, 520 TV lines, Varifical

iCanView222SB 410K Sony WDR, Varifocal iCanView222PB 410K Pixim WDR, Varifocal

Selectable options

Capital letters following the hyphen, “-“ indicate selectable options. Please refer to the following table for the options. Each capital letter indicates insertion of corresponding option. Note that there can be multiple capital letters to indicate presence of multiple options.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Option indicator Description Misc

W Wireless LAN (802.11b/g)

P Standard PoE (IEEE 802.3af) M Inclusion of embedded flash memory (NAND) N True Day/Night – IR cut filter

z Recessed Ceiling Mount Kit

iCanView222 is designed to be installed on a ceiling or the wall. Please refer to Appendix A.1 for default mounting of the iCanView222. For recessed ceiling mounting, an optional mounting accessory, mD112 is offered . Please refer to Appendix A.2 for more details of the installation.

Figure 1-1. Recessed ceiling mount kit (mD112)

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

2. Product Description

2.1. Contents

Open the package and check if you have the followings:

Components Description Remarks

iCanView222 iCanView222 Network Camera

Power adapter

Input : 100~250V 50-60Hz Output : +12V, 1.0A

Standard Power supplied

when standard PoE is

not selected

AC power cable AC 250V, 10A~16A

Standard Power cable supplied when standard PoE is not selected

Mounting bracket Standard ceiling mount bracket

CD-ROM Software & User’s Guide

Quick Reference Guide Quick installation guide Will be provided

2.2. Preview

iCanView222 IP-Installer i-NVR

1CH MPEG-4 Network

Camera

PC software to allocate an IP

address to the iCanView222

PC software to view and record

the A/V streaming data

transmitted from iCanView222

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Rev.1.0 (Mar. 2008)

2.3. Physical description

2.3.1. External View

Figure 2-1. Side view of iCanView222

2.3.2. Rear panel

Figure 2-2. Rear panel of iCanView222

Mic/Line In

Line Out

DC In

LAN

Sensor In

Relay Out

Serial (pin 1

at leftmost)

iCanView222 User’s Guide

y MIC /LINE IN : Connect external audio source or microphone. If external audio is connected,

embedded microphone will be disabled. Use Standard stereo earphone jack for the connection

Audio In

Ground

Not used

Audio In

Ground

Not used

Audio out

Ground

Not used

Audio out

Ground

Not used

Figure 2-3. Pin assignment of the plug for MIC/LINE In (left) and

LINE OUT (right)

y LINE OUT : Connect speakers with built in amplifier. Audio from remote site is output through

Line out in bi-directional audio mode.

Use Standard stereo earphone jack for the connection.

y 100BaseT 802.3af : 100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af).

- LINK LED : Continuous yellow light means that network cable is plugged in. It will flicker when there is traffic.

- Status LED: Green color indicates that the camera is in normal operation mode, while RED color indicates that the camera is in abnormal condition.

y RS-232C 3 Pins on the right of the connector are assigned for RS-222 port. Please note that leftmost

pin is numbered as 1.

Pin Description Misc.

1 Not used 2 Not used 3 RxD of RS-222C For debugging & factory use only. 4 TxD of RS-222C For debugging & factory use only. 5 Ground of RS-222C For debugging & factory use only.

y DC7-23V: Power input of iCanView222.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Do not apply power through this power input when Stan dard PoE connection is used.

y ALARM IN/OUT and Composite Video Output: Used for connecting P/T device, sensor, and alarm devices to iCanView222. Note that the bottom most pin is numbered as 1. Pin assignments are as follows

Pin Description Misc.

1 SNS IN (+) Sensor In (+). NC/NO selectable in

admin mode.

2 SNS In (-) Sensor In (-). NC/NO selectable in

admin mode. 3 CVBS OUT(+) Composite video output 4 CVBS OUT(-) Ground for composite video output 5 RLY OUT Relay output : closed circuit in alarm

to indicate alarm status

6 RLY OUT

 SNS IN : Connect external alarm sensors such as the infrared sensors, heat sensor,

magnetic sensors, etc. NC/NO selectable in the admin page.

 RLY OUT : It is used for connecting external alarm generators such as sirens,

flashing light, etc. When activated, relay output configures a closed circuit.

Please refer to Section 6.1 for more detailed description on the Alarm In/Out connections.

y Reset : Factory Default Switch

There is a switch provided for returning the network camera to factory default state. Open the

dome cover to access the switch. Press the switch through a tiny hole using tools with sharp tip for a few seconds while power is applied.

2.4. PC Requirements

AV streaming data received from iCanView222 can be decoded or stored in a PC running i-NVR program which is a viewing & recording program for a PC. Minimum requirement of the PC is described below:

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Minimum Recommended

CPU Pentium III 700 Pentium IV 1.2G above

Main Memory 128 MB 256MB above

Operating system* Windows 2,000 or later Windows 2,000 or later

Web browser Internet Explorer 5.0 Internet Explorer 5.0 above

Resolution 1,024 X 768 Higher than 1,024 X 768

Network 10 Base-T Ethernet 100 Base-T Ethernet

* Operating Systems supported : Windows 2000 Professional

Windows XP Professional / Windows XP Home Edition

2.5 Quick Installation Guide

Brief information for rapid installation is provided in this section. For more detailed information you are recommended to refer to pertinent documentations provided with the product or refer to iCanTek’s home page (http://www.icantek.com)

1. Connect iCanView222 to LAN by using one of the following method

1) If your iCanView222 has standard PoE option, connect the network camera and PC as illustrated in Figure 2.4. Both power and network connections are made with a single LAN cable. Make sure that you are using hub supporting standard PoE (802.3af).

2) If your iCanView222 does not support standard PoE or you don’t have hub supporting standard PoE, connect iCanView222 as in Figure 2.5. The DC power is applied through AC adaptor.

2) If you have standard power connect the network camera and PC as illustrated in Figure

2.6.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Figure 2-4. Connecting Network camera using Standard PoE (802.3af).

AC A

daptor

Hub

AC In

100BaseT

DC In

Standard PoE Hub

Figure 2-5. Conventional way of connecting network camera without standard PoE.

<Caution> When power is applied through standard PoE, never apply power through AC adaptor. iCantek assumes no responsibility for the damages caused by collision of the power through the standard PoE and AC adaptor.

2. Install “IP installer” and “i-NVR” on your PC.

Detailed information for installing these programs can be found in [IP-Installer User’s

Guide] and [i-NVR User’s Guide], respectively.

3. Assign IP address to iCanView222 using IP installer.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Identify the type of the network environment and set up IP address. Detailed process of setting up IP address can be found in [IP-Installer User’s Guide]. If network type is xDSL or Cable modem you need supplementary information provided by your ISP.

4. Connect to iCanView222 in Administrator Mode for initial parameter set-up.

All parameters are set to factory default state when iCanView222 is delivered. You are asked to configure the system for your environment in administration mode. Detailed information of using administration mode can be found in [5. Configuring iCanView222

in Administrative Mode]. Among the parameters, the parameters in the following table

should be set-up with proper values. Detailed information for the parameters in Administrator Mode is found in [5. Configuring iCanView222 in Administrative Mode]

[Note]: Set-up values are preserved even the power is turned off.

Page Parameter Setup value Factory default value

Basic Setup

Video Size

Set the resolution of the video transmitted from iCanView222.

Make sure that you press Check button to find out the number of maximum possible simultaneous

sers then set the number of

users smaller than or equal to the

mber.

Max Upload Rate

Set this value smaller than the upload speed of your network.

Frame Rate

The number of frames to be transmitted per second.

Video Rate

Bandwidth assigned for video transmitted from iCanView222.

User Admin

& Time

Setup

Administrator

name &

password

For safety, you are recommended to change these values from factory default. For new connection, you need to input changed values for corresponding fields. Do not disclose these values to others and memorize these values.

Default value

Username : root

Password : dw2001

User Admin

& Time

Setup

Current Time

Input correct time in this field.

Default value :

2001/1/1

5. Connect the input and output signals to iCanView222.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Connectors Function Signal description Number

LINE-

In/MIC

Audio in

Connect microphone or output from audio devices.

Line Out

Audio out for

speaker

Audio from remote site is available from this connector in bi-directional audio mode. Connect speaker with amplifier.

SENS IN

Connecting

Alarm Sensor

IR sensor, Motion Sensor, Smoke Detector…

RLY OUT

Connecting

Alarm

annunciating

device

Siren, Flashing Light, …

100Base-T

802.3af

Network

connection

Connect iCanView222 to the network, LAN, ADSL or Cable modem.

CVBS OUT

Analog Video

output

Composite video output from the camera module.

6. Remote video connection to iCanView222

Run i-NVR on your PC. Before connecting to iCanView222 it is needed to configure the connection information on the i-NVR. More detailed information of using “i-NVR” can be found in [i-NVR User’s Guide].

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

3. Connecting iCanView222 to Network

iCanView222 supports LAN, xDSL, and Cable modem. It also supports shared IP environment where single IP address is shared by at least 2 IP devices. Refer to [IP-Installer User’s Guide] for details of setting the IP address for iCanView222.

3.1. Connecting to LAN

In case of connecting the iCanView222 to LAN, it is generally connected as in Figure 3-1.

Figure 3-1. Connecting the iCanView222 to LAN

1. Follow through steps 1 to 3 in Section 2.5 to assign IP address to iCanView222.

2. Install iCanView222 and connect it to desired LAN.

3. Check if you can receive video data when connecting to iCanView222 using the viewer program.

4. When one or more IP video products are connected through a IP sharing device (i.e. router) to a larger network (i.e. the internet), in order to access each unit from outside the local area network, each device must have a unique RTSP (Real Time Stream Protocol) and HTTP port number. You must also configure your IP sharing device for “port forwarding”. This is to enable the IP sharing device to forward packet data with unique port number (RTSP and HTTP) to unique internal IP

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

address (local IP address). If you only plan to access multiple units from within a local area network, you do not need to change the RTSP and HTTP port numbers, unless other IP sharing devices sit in-between the client and the IP video products. For more detailed information regarding the use of IP sharing device refer to the document [Use of Private IP network using

IP-sharing-device].

②

3.2. Connecting to xDSL/Cable Modem

1. Follow through steps 1 to 3 in Section 2.5 to assign IP address and other network parameters to iCanView222.

2. Install iCanView222 and connect it to xDSL or Cable modem as in Figure 3-2.

Figure 3-2. Connecting the iCanView222 to ADSL Modem

When fixed IP address is assigned to the xDSL or Cable modem, follow the same way as

assigning IP address for the case of LAN using IP-installer. To enable the notification of the changed IP address to the user over e-mail when the IP address is changed in floating IP environment, you have to assign the e-mail address when user name and password are

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

input using IP-installer. (Management server provides a convenient way of

connecting to your network camera under dynamic IP environment. Please refer to the Application note regarding “Management Server” in the CD.)

When connecting iCanView222 to x DSL or Cable modem, usually regular LAN cable is

required. But since some modems have crossover connections, please contact your service provider for detailed information.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

4. IP-Installer

iCanView222 needs IP network parameters for connection to the network(Internet/Intranet). IPInstaller is a PC program for the initial network configuration to IP video products such as Network Camera or A/V Server. IP-Installer is provided in a CD supplied with iCanView222 or it can be downloaded from “www.icantek.com

”.

Detailed information of Installing and running IP-installer can be found in [IP-installer user’s guide]

4.1. Main window of IP-Installer

Figure 4-1. IP Installer

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

All the basic network parameters needed for the initial connection to IP video products can be assigned by IP-Installer. Once the basic parameters are assigned and the initial connection is successfully made, you can connect to the administration page for more sophisticated control of the network parameters and other operational parameters. Refer to Chapter 5 for more details of the administration page.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5. Configuring iCanView222 in Administrative Mode

5.1. Log On

There are 2 ways of connecting to iCanView222 administrative mode. One is through Internet Explorer and the other is through “i-NVR” program.

1. Using Internet Explorer

Type in the connection address of the network camera in the address window of the Internet Explorer as followings:

http://[iCanView222 IP address]/admin.htm

Example: http://172.16.64.133/admin.htm

If you changed the HTTP port from default value you can login by typing in:

http://[iCanView222 IP address]:[HTTP port]/admin.htm

Example: http://172.16.64.133:8080/admin.htm

2. Log on from “i-NVR”

Select video channel in the viewing window of “i-NVR”. Selected video channel will be

highlighted. Click

button on the right side of the display screen.

Figure 5-1. Select display channel and click “Camera Admin” button for Log on to

administrative mode from “i-NVR”

3. Input User Name and Password in the display screen shown in Figure 5-2.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Figure 5-2. Log On Screen

Factory default User Name and Password are set as ‘root’ and ‘dw2001’, respectively. Click on “OK” button to enter into the Basic Setup page of Administrative M ode. If you have changed th e username and password of the Administrator, you must log on with the changed username and password.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.2. Basic Setup

Setup the basic parameters of the iCanView222.

Figure 5-3. Basic Setup

Field/Button

Sub Field

/Button

Description

Language

Select a language of your choice

System Name

Logical name of the iCanView222. It is same as the one set-up by IP-installer. You can reassign the system name.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Audio Input

Selection

Select the type of input audio.

z Select Line In for using Line-out from audio devices. z Select Mic for using microphone.

Video Quality

& Bandwidth

Control

Input Video This filed is set by the factory

Video Size

Select a video size for transmission-

z NTSC(30 frames/sec Max.) : 176x144 / 352x240 /

720x480.

z PAL/SECAM (25 frames/sec Max.) : 176x144 /

352x288 / 720x576

Max upload

rate

Assign maximum bandwidth of the uplink for the network connected to iCanView222.

Frame rate

Assign number of video frames to be transmitted for each second. You can improve picture quality by lowering frame rate for the same bandwidth.

Video rate Assign bandwidth for transmitting video data.

Audio rate

Assign bandwidth for transmitting audio data. Audio data is not transmitted if you select “NA”

Check

After you finish set up of video and audio for all the channels, click on this box to obtain the possible maximum number of

users (Possible Max Users) and remaining network bandwidth (Remained) remaining when possible maximum

users are connected.

Possible Max

Users

It shows the number of maximum simultaneous connections for the network connection set-up.

Remained

It shows the network bandwidth remaining when Possible Max

Users are connected.

Limited users

Useful network bandwidth varies according to the condition of the network. This parameter is used to limit the number of the simultaneous connections below the number shown in Possible

Max Users.

Save

Save the set-up parameters when the set-up parameters are done.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.3. Network Configuration

Setup the network parameters appropriately in accordance with your network environment. Many of the parameters in this page are same as those set up by “IP-Installer”.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Figure 5-4. Network Configuration

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Field/Button

Sub Field

/Button

Description

IP Assign Type

The network types supported by the iCanView222 are LAN(fixed IP), PPPoE, and DHCP(automatic IP allocation)

Static IP Set

When the network environment is fixed IP, select ‘LAN’ in the network type, and put the IP address, Subnet Mask, Gateway, DNS1 and DNS2. Ask your network administrator or ISP for the information. DNS2 is used when DNS1 does not work.

PPPoE Setup

When the network environment is PPPoE and IP address is assigned automatically, select ‘PPPoE’ in the network type. Next, fill in the ‘User Name’ and ‘Password’ fields with the values assigned by the ISP.

DHCP Setup

When the network environment is “automatic IP allocation by DHCP”, select ‘DHCP’ in the network type. For cable modem connection, select this mode. Refer to [IP-installer user’s guide] for “Host name and domain for Cable Modem

Clone MAC Refer to [IP-installer user’s guide] for “Clone MAC”

Port Change

Each port should have a number below 65535.

RTSP

The RTSP port is used for transmitting real time audio/video data from the network camera. Default is 554.

HTTP

HTTP port is used for the connection to the admin page. Default is 80.

IP Filtering

You can restrict the access to the administrator page from IP addresses beyond certain IP address range.

Restrict

Administrator

Access

Check at this box to restrict administrative log on.

Base IP

Address

Input IP address of the PC which is intended to be used for log on to administrative mode.

Mask

This is same as subnet mask. It is used to allow administrative log on only to the PCs located in the same subnet as the base IP address. If you want to allow only one PC to access in administrative mode, set this value to 255.255.255.255.

E-Mail Setup

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Notify for IP

Change

If you check this, the IP address will be sent via E-mail whenever the IP address changes. It is sent to the E-mail address set by “Recv E-Mail Address”.

Recv E-Mail

Address

Enter E-mail address to receive information sent from your network camera. This is same as E-mail field in IP-installer.

Return E-Mail

Address

Fill in this field with correct e-mail address to identify the mail sent from the network camera

Using Built-in

SMTP Server

If you are using web mail services having no SMTP server, check the radio button at the left of “Using Built-in SMTP Server” and enter valid e-mail address to avoid spam filtering on the receiving e-mail server.

Using

External

SMTP Server

If you are using external mail server, fill in the fields with proper parameters.

FTP Server

Setup

Setup IP address, Username, Password and Directory of FTP server to send data in case of alarm. Default FTP port number is 21.

Management

Server

You can register the network camera to the Management Server (DDNS Server) for name service to your network camera.

Log on to

server

Check this box to enable log on to the management server. By log on to the management server your network camera can use domain name instead of numeric IP address. This feature is particularly useful when your network camera is using dynamic IP address. Input valid management server (DDNS Server) name for the service. You must have an account on the management server (DDNS Server) and register your IP video devices under your account to use this feature.

Domain name of your network camera can be assigned when you register your network camera to the management server under your account. One of the servers available is mgmt.net-video.net. For opening an account, visit www.net-video.net

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.4. Wireless Configuration

For the case of a network camera having built in wireless LAN it is needed to set up wireless LAN configuration parameters. Click “Wireless Configuration”.

Figure 5-5 Wireless Configuration

Field/Button

Sub Field

/Button

Description

Wireless LAN

Setup

WLAN Mode

Select “ESS” to use wireless interface. If “Disable” is selected, Ethernet interface is used instead of wireless LAN interface.

WLAN Radio Select the mode of Wireless Radio.

SSID

Enter the ID of the wireless LAN access point to be connected when wireless LAN interface is selected.

Authentication Select the type of authentication.

Encryption Select the mode of encryption. If encryption is not needed,

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

select “OFF”

Key Set the value of encryption key or pre-shared key.

Power level Set the maximum transmission power level or wireless LAN.

WLAN

Information

MAC Address Indicates MAC address of the wireless LAN.

BSSID

Indicates the ID of the connected access point. In general the MAC address of the access point is shown.

Current

Channel

Indicates the channel number of present connection.

Signal

Strength

Indicates the strength of the received signal.

Link Quality Indicates the quality of Link level.

Tx Rate Indicates the speed of the latest transmission

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.5. CCD Adjustment

You can optimize the quality of input video by adjusting the parameter of CCD. To enter into this mode, click “CCD Adjustment” in administrative page. You will find a screen shown in Figure 5-6.

Figure 5-6. CCD Adjustment

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Field/Button

Sub Field

/Button

Description

Lens Selection

Standard iCanView222 is delivered without lens. Any lens having C or CS mount type can be installed on iCanView222. A C-CS adaptor is packaged with iCanView222 for accommodating CS type lens. Confirm whether your lens is Non DC IRIS or DC IRIS lens before your selection and then click “SAVE” to save your selection.

DC IRIS Lens

DC IRIS lens is a kind of auto IRIS lens. Opening of IRIS can be adjusted by applying DC voltage. The opening of IRIS is optimally adjusted by detecting the signal level from CCD. This type should be selected when DC IRIS lens is mounted on your iCanView222.

ELC Manual Lens without IRIS control

CCD Control

Backlight

Compensation

When the camera is acquiring video from object with bright backlight, it is hard to identify the details of target object since the object appears very dark. Apply backlight compensation mode for this case. Default mode is backlight compensation Off.

Auto Gain

Control

If you set the value to ON, the gain is automatically adjusted in accordance with the illumination condition.

Flickerless

In case of using NTSC type iCanView222 in 50Hz AC regions or using PAL type iCanView222 in 60Hz AC region, video output tends to flicker when iCanView222 is used under fluorescent lamps. This mode reduces the flickering phenomena. If this mode is selected, electronic shutter speed is set to 1/100 sec for NTSC camera while it is set to 1/120 for PAL camera to synchronize the shutter speed to AC current.

<Note> : Make sure that you apply this mode only when using NTSC camera in PAL region or PAL camera in NTSC region.

AWB

AWC : Apply this mode for normal usage. This mode provides even color reproduction for wide range of color temperature. ATW : This mode provides coverage for narrower color temperature.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Sharpness Adjust the sharpness of the video D C level Adjust the brightness level by adjust this value. Color Blue Adjust the amount of blue in the video. Color Red Adjust the amount of red in the video

Restore

Original Values

Apply original setting of the values.

SAVE Click “SAVE” to save your selection.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.6. User Admin & Time Setup

You can change the ID and password of users and also assign different attributes for each user.

Figure 5-7. User Admin. & Time Setup

Field/Button Sub Field Description

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

/Button

User

Administration

Administrator

Username

Admin ID. Default ID is “root”

Administrator

password :

Admin password. The default password is “dw2001”.

Administrator

Confirm

Password

Enter the password once more to confirm the password.

Add User

Username

Enter the user ID you want to add. Up to 100 users are supported by iCanView222.

Add User

Password

Enter the user password.

Add User

Attribute

You can set different system resource access capabilities for each of the users.

z Attributes are Audio, Bi-directional Audio and Pan/Tilt

control.

z For example, if you want a specified user to hear the

audio from the iCanView222, check Audio in the check box.

User List

You can list “user ids” and “ their attributes” here.

z format : user id[A, BA, P] :

 A – audio,  B – bi-directional audio,  P – pt(Pan/Tilt), attribute.

You can delete specific user by clicking the DELETE button.

Authentication

for Viewing

YES

SAVE

If you want to restrict viewing access to the iCanView222, check at the box left to Yes and click on Save. Users need to input ID and password to connect to iCanView222 in viewing mode in a pop up window as shown below..

Figure 5-8. User Authentication in iCanView222

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

If No, default

attribute

If you uncheck for the Authentication for Viewing, all users can access the iCanView222 with the same attribute set here. Checked attributes are enabled. Click “Save” to save the attribute.

Time Setup

Current Time It shows you the current time of iCanView222.

Synchronize

with an

Internet

Time Server

Synchronize the time with the internet time server at the right. When the time server is out of the reach from iCanView222, you can assign time server by filling in Specific Time Server field.

Synchronize

With this

Computer

Time

Synchronize the time with the time of the PC.

Set Manually Set the time manually. Fill in the fields with desired formats.

SAVE Save the set up parameters

If you lost Administrator’s ID and password, the only means of recovery is to reset the settings to factory default, but then you lose your previous settings.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.7. Sensor & Capture Setup

This is the setup page for sensors and video capture conditions. Captured video can be sent to user by FTP or E-mail upon configuration.

Figure 5-9. Sensor & Capture Setup

Field/Button

Sub Field

/Button

Description

Sensor Setup

Sensor 1

Select sensor type. There are two types of sensors which are

Normal Open and Normal Close.

Name

Input logical name for the sensor.

Video Capture

Condition

It sets the condition of video transmission via FTP or E-mail. The iCanView222 supports 2 types of conditions which are mutually independent.

1. Sensor initiated: when at least one of the sensor detects alarm condition.

2. Motion-Detection initiated : when motion is

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

detected from video channel

Sensor

Select

Check to enable Sensor initiated capture.

Motion

Detection

Select

Check to enable motion detection initiated capture.

Captured

Video

Transmission

Select a way of sending captured video. You can send captured video through FTP or E-mail, or both.

By E-Mail

Check to send captured video by e-mail.

E-mail is sent to the Recv E-mail address. Refe r to [Section

5.3.]

Captured video data for E-mail consists of intra frames only in consideration of the limited storage space for E-mail account. FTP data contains entire video frames.

By FTP

Check to send captured video by FTP.

FTP is sent to the FTP Server. Refer to [Section 5.3.]

If the FTP server is not properly assigned in “Network Configuration” mode, iCanView222 ignores the video transmission by FTP

SAVE Save the setup parameters.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.8. Alarm Device Setup

Test the alarm output and describe the condition of alarm annunciation.

Figure 5-10. Alarm Output Setup

Field/Button

Sub Field

/Button

Description

Alarm Device

Test

Test alarm devices. Click on On/Off for testing Small box with white background indicates the status of the relay by On/Off.

ON On the alarm output (close the relay contact)

OFF Off the alarm output (Open the relay contact)

Sound Test -

Alarm Device

Active

Condition

Setup the condition of activating alarm device. Select sensor or motion detection as the condition.

Name

Logical name of the alarm device can be input into the box at the left.

Sensor Check at the box at the left of to allow alarm generation upon

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

sensor input.

Motion

Check at the box at the left to allow alarm generation upon Motion detection

Duration

Set the duration of Alarm annunciation. 10 sec, 30 sec, 1 min, 2 min, 5 min, 10 min, 30 min, 1 hour.

SAVE Save the setup parameters.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.9. Motion Region Setup

Set the motion detection regions. Up to 3 regions can be defined.

Figure 5-11. Motion Region Setup

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Field/Button

Sub Field

/Button

Description

Channel

Selection

Not applicable.

Channel

Sensitivity

Set the sensitivity in motion detection for each channel. 1 is the most sensitive, and 10 is the least sensitive.

Motion Region

Setup

Set up to 3 the motion detection zone

Region 1, 2,

or 3

Enable each zone by checking the box at the left of each Region.

. To set the region,

1. Click on START and click on a box overlaid on the video

2. Click on END and click on a box overlaid on the video.

3. The defined motion detection zone will be indicated with corresponding colors.

Legend of the color :

red(region 1), green(region 2),

blue(region3). START Enable selection of rectangular zone start. END Enable selection of rectangular zone end. SELECT Click on this button and click on desired rectangle to add or delete

the rectangular region to the motion detection zone.

Percentage This value controls the sensitivity of each region.

1 is the most sensitive and 100 is the least sensitive

RESET Clears the start & end point to (0,0) & (0,0)

SAVE Save the setup parameters.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.10. Encryption Set up

Figure 5-12. Encryption Setup

For additional security to the video and audio data transmitted from the network camera, you can set key codes and use them for encrypting the data from the network camera. You can selectively activate encryption for the video and audio data. For enabling the encryption, check at the box at the left of the “Enable data encryption” then check at the proper check boxes at the left of “Video” and “Audio”. After the selection, click on SAVE button beneath the “Video” and “Audio” check boxes.

Field/Button Sub Field Description

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

/Button

Enable Data

Encryption

Check at this box to apply data encryption. If it is unchecked encryption is applied on neither video nor

audio data regardless of the selection below. Video Check to enable encryption on the video data. Audio Check to enable encryption on the audio data. SAVE After the selection, click on SAVE button.

Key Value

You can use up to 20 different key codes for the encryption of

the data

GENERATE

To generate the key value click on “GENERATE” button. The

boxes for the Key values will be filled with new values.

SAVE

Save Key value on the network camera: Click on SAVE

button beneath GENERATE button to save the key value

generated by the network camera.

DOWNLOAD

Download Key value to your PC : The key values can be

downloaded and stored as a file to your PC for reference when

you make connection. When encryption is enabled, the PC

client program will ask for particular key value out of the 20

available key values.

INSTALL

Upload key value to the ne twork camera : The key value

stored on your PC can be uploaded to your network camera.

This feature is useful when you manage multiple network

cameras having same key value sets. Select a file having key

values then click on “INSTALL” button to upload the key values.

Find file saving the Key value before uploading to the network

camera.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.11. Upgrade & Reset

You can upgrade the iCanView222 via the IP network.

Figure 5-13. Upgrade & Reset

For each of the upgrade of the system component, upgrade code should be downloaded from iCanTek’s home page before the system upgrade is performed. (Refer to [6.4. How to Upgrade Your iC anView222 System]

Field/Button

Sub Field

/Button

Description

Automatic

Upgrade

Automatic upgrade is a feature that enables network camera to

upgrade to newly released system software by automatically

connecting to upgrade server. Click on check button to find the

availability of upgrade firmware.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Note that automatic upgrade is not supported for

standard product.

Manual

Upgrade

Upgrade the system manually.

System S/W

Upgrade

Upgrade the system software installed in the network camera

via the network. System software needed for the upgrade can

be downloaded from iCanTek’s home page.

Refer to [6.4. How To Upgrade Your iCanView222

System].

Bootloader

Upgrade

Upgrade the bootloader installed in the network camera via the

network. Bootloader needed for the upgrade can be

downloaded from iCanTek’s home page.

Refer to [6.4. How To Upgrade Your iCanView222

System].

Add PTZ File

Add a new PT driver software via the network. PT driver can be

downloaded from iCanTek’s home page.

Refer to [6.4. How To Upgrade Your iCanView222

System].

Factory Default Setting

Re-initialize the network camera to factory default state.

By checking on a Radio button “Except Network Configuration”,

you can preserve the parameters for the network. Checking on

“All”, will return all the parameters to factory default state.

Once iCanView222 is re-initialized as factory default

state, it should be set-up again using IP-Installer.

System Reset

Perform remote reset by clicking the “CONFIRM” button.

All previous connections will be disconnected upon

reset. iCanView222 does not resume the connections

and the users must re-connect to the server manually.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

5.13. Status Report

It shows you system records since the system started.

Figure 5-15. Status Report

You can check the problems as well as the versions and event status of the whole system and each module.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

6. Tips for using iCanView222

6.1. ALARM-IN and ALARM-OUT

ALARM connectors are used to connect various sensing and alerting devices. Examples of sensing devices are infrared sensors, motion sensors, heat/smoke sensors, magnetic sensor, etc. ALARMOUT is used for connecting alerting device such as loud speaker, flashing light, etc.

CVBS GND

CVBS Out

Sens In - Sens In +

Relay Out

Figure 6-1. Terminal block for I/O connection

1. ALARM-IN

Connect the two wires of the sensors to “SNS IN”. The sensor type can be set in Administrative mode(Ref. 5.7). Output lines providing on-off switching are connected

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

between “+“ and “-” pins. Figure 6-2 shows the input circuit of “SNS IN”.

SNS IN (+)

SNS

IN (-)

Figure 6-2. SENSOR input of iCanView222

2. ALARM-OUT

A Relay output is provided for connecting alarm devices or for remote on/off devices such as light control. Relay circuits are normal open and circuits are closed upon alarm output or remote on. The relay is capable of switching AC/DC 30V,1A electrical signal.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

RLY OUT

Figure 6-3. RELAY Output of iCanView222

3. Connection of Sensor, Alarm Device

3.1 Connection of Sensor

Sensor Device

Sensor

Power

Supply

NO/NCType

Sensor1-

Sensor1+

+12V

GND

Sensor

Device

Sensor

Power

Supply

Open CollectorType

Photo Coupler

3.2 Connection of Relay

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Rev.1.0 (Mar. 2008)

Alarm

Out

Device

Relay1

Power

Supply

(1~30

VDC/AC,1A )

1~30

VDC/AC,1A )

Relay1

Relay Switch Power Supply

1V~30VDC /AC,1A

Optional

Relay Switch

Alarm

Out

Device

Power

Supply(30V

Relay

6.2. Trouble Shooting

1. After iCanView222 is successfully installed.

• iCanView222 in viewing mode, neither channel name nor video is display and eventually timeout message is shown up.

Check the power and network connection of iCanView222.

To check if the network is properly operating, open the browser and try to connect to any server.

Example) http://www.yahoo.com

Or open the MS-DOS Prompt and type the following.

ping www.yahoo.com

Then press Enter. If you see the “ Reply from …” message it means that the network is working properly. To check if the iCanView222 is connected, open the MS-DOS Prompt and type the following.

ping [the IP of the server]

Example) ping 192.168.1.112

If you see the “Reply from …” message, it means that the server is properly connected.

You can use the supported relay output to directly drive a maximum load of 30V AC/DC at 1A. By connecting additionally relay circuitry (such as optional relay switch), it can also drive heavier loads.

iCanView222 User’s Guide

If you do not see a Reply message, check if the network cable and power cable are properly connected.

2. After Successfully Connecting to the iCanView222

• Video movement is slow.

In Basic Setup of Admin Mode, lower the “Quality”. High quality means more data. You can also set the “Max. upload rate” to higher value. But this value must be lower than the maximum upload speed of your network. For example, if the maximum uploading bandwidth of the network is 400Kbps, set the total “Max. upload rate” as 384Kbps. If you set it higher, the video image can be corrupted with artifacts. Ask your network manager or ISP for maximum uploadin g bandwidth of the network.

• The image is dull and I see green, pink dots.

This could be caused by performance limitation of the PC. Do not run too many programs while running viewer program. The other reason could be missing data while transmission from iCanView222.

• Mosaic phenomenon.

Mosaic phenomenon occurs when not enough network bandwidth is available considering the resolution and frame rate of the video. Example is 704x480 video with low Max. upload rate. Users are recommended to adjust resolution and frame rates to lower values for lower bandwidth network.

6.3. Web Viewer

iCanView222 is designed to be connected through internet explorer, too. For connection to iCanView222 using internet explorer type in IP address or host address in the address input field of the internet explorer.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Figure 6-4. Web Viewer of iCanView222

z Control Panel of Web Viewer

Enable bidirectional audio. When bidirectional audio is enabled, voice from your PC is delivered to iCanView222. Capture and store the still image on your desk top screen.

Connect to iCanView222 in administrative mode of iCanView222.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Rotate the screen by 180 degree.

Connect to iCanView222.

Stop the connection.

Contrast, Brightness, and Volume adjustment..

Check the box to mute the audio.

Adjust the size of the screen. Normal (x1), Twice (x2), Half (1/2), Full Screen (full) On/off the relay by pressing the button Shows the status of the sensor. Blue color means that the sensor is in normal state, while red color indicates alarm situation. Number on the button indicates the number of sensor.

Move the center of the camera in up/down/left/right directions.

Z+

Z-

Zoom in (Z+) Zoom out (Z-)

Not applicable for iCanView222.

F-

Move the focus to further position.

Not applicable for iCanView222.

A/F

Auto focus.

Not applicable for iCanView222.

F+

Move the focus to nearer position.

Not applicable for iCanView222.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

6.4. How to Upgrade the iCanView222

Unless otherwise instructed, the owners of the iCanView222 are recommended to upgrade the

system when upgraded firmware is released using manual upgrade procedure.

Followings are the procedure to apply for the manual upgrade

1) Save the upgrade system software to your PC. Upgrade software can be downloaded from iCanTek’s home page or provided in CD.

2) Log on to administrative modeand select “Update & Reset” menu.

3) Click "Browse..." to find the files you want to use for upgrade. This will open a "Ch oose file"

dialogue window. The file extension is “ief”.

4) When you've found the file, click "Open." This will select the file an d close the "Choose file"

dialogue window.

5) Click the "INSTALL" button. An alert message box will pop up. Click “OK” button then it will

start uploading the file. This may take some time.

6) Upgrade completion message will appear after the system upgrade has been completed.

7) Reboot iCanView222 by performing “System Reset”.

8) After rebooting, log on to the server in administrative mode again and click the “Status

Repor t”.

9) Check the version number and release date of the iCanView222.

You can download iCanView222 system software from iCanTek’s homepage. http://www.icantek.com

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Appendix. On Site Installation

A.1. Ceiling or Wall Mounting

Please follow through the steps indicated by the number on sequence for the installation on the wall or ceiling.

1. Fix the mounting bracket.

2. Seat the IP camera onto the mounting

bracket. Make sure to align the angular positions of the “mounting knobs” and mating “mounting bracket holes” properly. Once seated, rotate the camera to the right until it is locked.

3. Open the cover and apply a screw through

the hole indicated by the arrow to prevent the camera from rotation.

4. Place the cover.

Mounting

Bracket

Mounting Knobs

Mounting Knob

Holes

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

A.2. Recessed Ceiling Mounting (mD112 recessed ceiling mount kit required)

For the recessed ceiling mounting, please use optional recessed ceiling mounting kit, mD112. Follow through the steps indicated by the number in sequence for recessed mounting.

Rev.1.0 (Mar. 2008)

iCanView222 User’s Guide

Note 1 : Aligning “Mounting Knobs” and “Mounting knob Holes”

Rev.1.0 (Mar. 2008)

iCanTek iCanView 222, iCanView 222W User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual