iBuid SH1 User Manual

Notice Before Using

SH1

Speciﬁcation

SH1

Package Contents List

SH1

SH1 Bluetooth® Headset Overview

SH1

Battery information

SH1

Charging the battery

SH1

Charging the battery

SH1

Pair to your Bluetooth® phone

SH1

Pair to your Bluetooth® phone

SH1

Turning headset on /off

SH1

01. Notice Before Using

Thank you for purchasing the Bluetooth Please read this User's Manual completely before you use the Headset. SH1 designed for listening the high quality music wirelessly that based on the latest Bluetooth SH1 can be easily connected to a mobile phone for call conversation and music listening. It is also capable to connect to the other Bluetooth Notebook, iPod etc. SH1 is compliant with Bluetooth V3.0 speciﬁcation, supports HSP, HFP, A2DP and AVRCP proﬁles. Please make sure your phone or other device supports these proﬁles.

9. Using for music play

Play/Pause

Press Power/Play button to get the music play or pause.

Next/Previous song

Press and hold Next button to skip to next song or chapter, press and hold Previous button to go back previous song or chapter.

Increase/Decrease volume

Press Volume Up button to increase volume, press Volume Down button to decrease volume.

Headset SH1.

wireless technology.

-enabled devices like

Using for music play

SH1

02. Speciﬁcation

Bluetooth® speciﬁcation: V3.0 Supported proﬁle: HSP, HFP, A2DP, AVRCP Operation range: Up to 10 meters Talk time: 6 hours Play time: 5 hours Standby time: 200hours Charge time: 1 Hours

Using for phone call

SH1

10. Using for phone call

Last number re-dialing

At standby status, double press the Answer, the last number you dialed will be re-dialed.

Note: The last number re-dialing is available only for the ﬁrst device if two Mobile phones are

connected. The connection sequence can be determined by reconnect manually.

Answering a call

Press Answer shortly to answer the incoming call.

Reject an incoming call

Press and hold Answer for 2 seconds to reject the incoming call.

Transferring a call

Press and hold Volume Up for 2 seconds to transfer the call between the phone and headset.

Ending a call

Press the Answer shortly to end a call.

03. Package Contents List

Please inspect this package and refer to the package contents list below to verify all items were included in this package:

1. SH1 Bluetooth

2. USB Charging Cable(1)

3. User's Manual(1)

4. Ear Cap (2)

Call-waiting

- If there is an incoming call while a call is in progress, press Answer shortly to accept the waiting call and end current calling.

- If there is an incoming call while a call is in progress, press and hold Answer for 3 seconds to accept the incoming call and place the current call on hold.

Note:The same operation could be performed in case of Multi-connection.

Volume adjusting

Press the Volume Up and Volume Down button to adjust the volume.

Mute

While a call is in progress, press and hold Volume Down button for 2s to mute the headset, a remindful tone would be heard every 10 seconds. Repeat the operation to un-mute.

headset(1)

Using for phone call

SH1

04. SH1 Bluetooth® Headset Overview

Ear Cap

Indicator

Volume Up/Previous

Volume Down/Next

Pairing/Answer,Power/Play

Safety and general information

SH1

11. Safety and general information

1. Please read this User's Manual carefully and follow all instructions.

2. To avoid any damage or malfunction of the device do not drop the device from high places.

3. Keep device away from humidity, water and any other liquid. If the device is exposed to water, moisture and other liquids do not operate it to avoid any electrical shock, explosion and damage to the device or yourself.

4. Do not place or keep this device near any heat sources, such as, direct sunlight, radiators, stoves or other apparatus that produce heat. This may cause an explosion, degrade the performance and/or reduce battery life.

05. Battery information

The device is equipped with an integrated lithium-polymer battery.

The battery cannot be replaced. Do not attempt to remove the

battery from the device since it would damage the device. The full

performance of a new battery is not achieved until after two or three

complete charging-discharging cycles. The battery can be charged

and discharged several hundred times, but it looses its capacity over

time.

Disconnect the SH1 from the power supply as soon as the battery is

fully charged, overcharging would reduce the service life of the

battery. A charged battery will lose its capacity if it is not used on a

regular basis.

Important: Ensure that the battery is fully charged if you do not use

the device for a long period of time. To avoid a complete discharge

of the battery, the SH1 should be charged at least every 3 months.

Safety and general information

5. Do not modify, repair or disassemble device (Especially the battery). Doing this will void the warranty.

6. Do not place heavy objects on the device.

7. Use only the supplied and approved chargers.

8. Unplug this device when unused for long periods of time or during lightening storms.

9. The battery used in this device may present a risk of ﬁre or chemical burn if mistreated.

SH1

06. Charging the battery

The SH1 is operated with a rechargeable battery. Charge the battery

completely before its ﬁrst use. Read the section "Battery

information" before starting the charging process.

1. Connect USB cable to a general USB power supplier.

2. Connect the charger to the correct outlet.

3. When the charger is connected to the headset, the red indicator

light will turn on. Charging the battery fully may take up to 1hours.

FCC & IC Statement

SH1

12. FCC & IC Statement

4) When the battery is fully charged, the red indicator light will turn

blue. Disconnect the charger from the headset and the outlet. The

headset is ready to use.

NOTE:

For ﬁrst time use, please charge the headset fully.

- The fully charged battery has power for up to 5 hours of talk-time and 4.5 hours music playing time, and up to 300 hours of standby time. However, the talk and standby times may vary when used with different mobile phones or other compatible Bluetooth® devices, usage settings, usage styles, and environments. When the battery power is low, the headset will remind you by voice prompt "Battery low" every 20 seconds, and the red indicator light starts to ﬂash.

- For using the SH1 with iPhone, an additional battery meter ( ) will be activated and the remaining battery capacity will display on your phone.

EC Declaration of Conformity

SH1

13. EC Declaration of Conformity

Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modiﬁcations to this equipment. Such modiﬁcations could void the user's authority to operate the equipment. This product is CE certiﬁed according to the provision of the R&TTE Directive (99/5/EC). This declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Please note that this

07. Pair to your Bluetooth® phone

Before you use your headset the ﬁrst time, you must pair the unit with a Bluetooth a one-time process and required only for the ﬁrst connection with the Mobile phone. The SH1 can be connected with two mobile phones simultaneously.

1. Keep the SH1 within 1 meter range of a Bluetooth

Mobile phone.

2. Press and hold the Power/Play button for about 5s, the

indicator light will ﬂashes red and blue intermittently, the device is now in pairing mode.

3. Find the Bluetooth

start the search for Bluetooth please read the operating instructions of your Mobile phone).

enabled mobile phone. Pairing is

setting of your Mobile phone and

devices. (For further details,

Warranty

-ready

SH1

product uses radio frequency bands not harmonized within EU. Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, and United Kingdom and within EFTA in Iceland, Norway and Switzerland.

14. Warranty

The condition of this warranty and supplier's responsibilities under this warranty are as follows: Warranty is non-transferable and is limited to the original purchaser only.

- You must be able to prove the date of original purchase of the unit with a dated receipt.

- The warranty is not applicable if the product has been subject to physical abuse, improper installation,

4. From the list of devices found, select the "SH1".

5. If required, enter the PIN code "0000" and conﬁrm the

entry. Once the pairing process was successful, the SH1 will connect to Mobile phone automatically then switch to standby mode, the indicator will ﬂash blue every 5 seconds.

NOTE:

- If pairing is not completed within 2 minutes, the headset will turn off. If this happens, please repeat the pairing steps.

- The SH1 supports Multi-connection that allows for the simultaneous use of the SH1 with two mobile phones. After paring successfully with 2 mobile phones, switch off the headset and switch on again, the headset will connect to both 2 mobile phones automatically. Otherwise, you can connect the headset on the cellphone manually.

SH1

Warranty

modiﬁcation or repair by an unauthorized third party.

- Supplier's responsibility shall be limited to the repair or replacement of the product at its sole discretion.

- Speciﬁcally exempt from any warranty are limited-life consumable components subject to normal wear and tear such as batteries, decorates and other accessories.

- Supplier is not responsible, for failure resulting from accident, abuse, misuse, or any unauthorized repair, or modiﬁcation.

- Modiﬁcation and repair of the unit should be done by an authorized and qualiﬁed service center or returned to the manufacturer.

- This warranty gives you speciﬁc legal rights, and you may also have other rights, which vary under local laws.

Visit www.ibuildhk.com or scan the QR code if you need more help.

08. Turning headset on /off

Turn on your headset

Long press the Power/Play for 3s to turn on your headset. If your headset has completed the pairing process successfully, when the headset is turned on, it will connect to the phone you last connected automatically. Please ensure your phone's Bluetooth

Turn off the headset

Long press the power button for 3s to turn off the headset. the Red indicator will ﬂash red.

NOTE:

- To conserve power, if the headset is not connected to a device for approximately 10 minutes, the headset will turn off automatically.

Bluetooth Earbuds

Quick start manual

function is active.

Model:SH1

Federal Communications Commission (FCC) Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.  Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

RF exposure warning

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.

iBuid SH1 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual