Interactive Touch Screen Monitor
User Manual
Contents
01 Security Warning
02 Introduction
02 Characteristic
03 Main View of Monitor
03 Accessories
04 Wall Mounts
05 Installation Notice
05 Bearing
05 Heat Dissipation
06 Installation Instruction
08 Control Panel
09 Interface Panel
09 Back Ports I
10 Back Ports II
11 Remote Controller specifications
11 Remote Controller Using Method
12 Remote Controller Introduction
13 Basic Connection Diagram
13 Operation instructions
13 Power on
13 Power off
14 OSD Menu
14 How to choose source channel
17 Introduction of “Menu”
17 Source Menu
17 Picture Menu
18 Sound Menu
18 Channel Menu
19 Set Menu
19 Supported Format under USB
Mode
20 PC mode(VGA
Input)specifications
21 FAQ Guide
25 Interactive touch monitor
Specifications
Product components of input voltage which is higher than safety voltage should be installed or placed out
of children’s reach.
Please use this product ’s standard power cable instead of other types to avoid burning the monitor and
In case of electric shock, the back cover should not be opened by non-professional maintenance staff.
Before operation, please make sure the compatibility between the local voltage value and the monitor’s
Please use three-phase power supply socket and make sure the earth wire is well connected.
Do not install or put the machine on places with heat source such as hot stoves, heat-transfer tubes,
When abnormal sound and smell appear, cut off the power supply and unplug the device immediately.
If the monitor will not be used for a long time, please unplug the power cable for safety.
Avoid liquid and metal’s getting into the machine.If any liquid or metal fall into the machine, please shut
It’s not allowed to use chemical reagent to wipe the machine , solvent may cause the cover ’s deterioration
Do not switch off/on machine frequently in a short time in case that it will affect the lifetime of the
In order to extend the service life of LCD screen, please do not set display brightness and contrast to the
Don't place the interactive touch monitor on unstable stand, bracket or table, otherwise interactive touch
You should be careful when move interactive touch monitor to avoid being hit, squeezed etc. Particularly
You should follow the manufacturer's instructions and use the manufacturer’s recommended installation
The wall mounting installation is available in normal cement wall, solid wall and wood wall which can
Avoid interactive touch monitor’s being exposed to direct sunlight, as direct sunlight will accelerate the
Do not use hard object to write on the touch screen monitor in case of scratching the glass and affect the
cause security risk.
rated voltage value. In the condition that the monitor will not be used in a long time,user should pull out
the plug from power socket.
power amplifiers, sources of direct strong light, dust, high humidity and places with mechanical vibration,
strike. In order to achieve better performance, please keep the monitor away from high voltage
distribution networks, large metal objects, radar station etc.
Stop using it and ask professional staff to resolve the problems until the problems are fixed.
the monitor down and cut off the power supply immediately and contact professional maintenance
personnel to repair.
or damage to the paint surface. We can disconnect the power supply and wipe it with warm wrung cloth if
there is dust or dirt. We can use clean soft cloth to wipe the screen part gently.
interactive touch monitor. After the normal shutdown, please wait about three minutes or longer then we
can turn on machine .
maximum value for a long time.
monitor may fall down and cause damage.
you should pay attention to the protection of the screen part to avoid glass breaking and causing damage.
accessories when you install the machine.
withstand three times weight or more of interactive touch display and please ensure good ventilation
condition; For the mounting on special wall (such as: steel structure wall, hollow structure, glass, marble,
etc.), it is recommended that you must evaluate force bearing of the wall first in case of emergency.
interactive touch monitor aging, and may cause the abnormalities of the touch device .
display effect.
Our interactive touch monitor is shelf-R&D interactive product. As a multi-functional teaching equipment,
Customized for teaching and conference system.
Equipped with High brightness, high contrast screen display. Screen is still clearly visible under the strong
When need low brightness display, you can choose to enter the automatic energy saving mode, reduce the
The touch monitor use advanced infrared touch sensor, HID without drive, plug and play.
Simulated mouse operation.
it contains function of interactive teaching, digital presentation, multimedia presentation, touch control
type operation, handwritten input, etc. From design to manufacturing, it is fully taken into consideration
of the characteristics for education industry, it is with easy and intuitive operation, has digital and
intelligent control, it has write , modify, delete, arbitrarily functions by using a finger or any
nontransparent objects, which is an ideal tool for the modernization of education.
Characteristic
light, indoor and outdoor environment.
backlight brightness, to achieve energy saving and environmental protection purpose.
User Manual Power Cable Touch USB Cable Audio Cable
VGA Cable HDMI Cable Touch USB Cable Eraser
Software CD Remote Controller Extend screw M8 screw
Pens Eraser Software CD Remote Controller
Bearing
Cooling ventilation
requirements
Distance to mounting surface(cm)
Mounting bracket should use the rack or mount that designated by manufacturer. If mounting bracket
is not from manufacturer, the bearing capacity should be ensured not less than the 4 times of its
actual bearing weight. The bearing capacity of the supporting disk for bearing the rack should not be
less than the 4 times of its actual bearing weight, and make sure the interactive monitor put stability.
The mounting surface which bearing the interactive monitor should be firm with enough bearing
capacity, which should not be less than the 4 times of its actual bearing weight. When the mounting
surface is the wall or rooftop of buildings, it must be solid brick, concrete or other strength equivalent
mounting surface. If the mounting surface is made of loose materials (old building brick wall,
woodiness, solid brick wall…), metal or non-metal structures, or the decoration layer of the mounting
surface is too thick, the strength of surface obviously deficient and corresponding reinforcement and
support measures should be taken to avoid safety hazard.
Heat Dissipation
Notes: when the monitor inlay wall or box, the vent area of bottom/flank/top sides should be
no less than 50% of packing surface and air circulation need to be keep well.
Diagram:
* Refer to CAS 132-2006 Standard
Step1, install the holder on the back of IFPD
Step2,install the wall holder parts to the wall
Step3, Hang the IFPD to the wall mount
Step4, finish