IBM PD78P083-A, PD78083, uPD78081, uPD78082-A, uPD78P083-A User Manual

...

Download

PD78083

SUBSERIES

8-BIT SINGLE-CHIP MICROCONTROLLER

PD78081

PD78081(A)

PD78082

PD78P083µPD78P083(A)

Document No. U12176EJ2V0UM00 (2nd edition) (O. D. No. IEU-886) Date Published May 1997 N

1994

1992

Printed in Japan

PD78082(A)

PD78P081(A2)

NOTES FOR CMOS DEVICES

1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS

Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it.

2 HANDLING OF UNUSED INPUT PINS FOR CMOS

Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to V possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices.

DD or GND with a resistor, if it is considered to have a

3 STATUS BEFORE INITIALIZATION OF MOS DEVICES

Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function.

FIP, IEBus, and QTOP are trademarks of NEC Corporation. MS-DOS and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. IBM DOS, PC/AT and PC DOS are trademarks of International Business Machines Corporation. HP9000 Series 300, HP9000 Series 700, and HP-UX are trademarks of Hewlett-Packard Company. SPARCstation is a trademark of SPARC International, Inc. Sun OS is a trademark of Sun Microsystems, Inc. Ethernet is a trademark of XEROX Corporation. NEWS and NEWS-OS are trademarks of SONY Corporation. OSF/Motif is a trademark of Open Software Foundation, Inc. TRON is an abbreviation of The Realtime Operating system Nucleus. ITRON is an abbreviation of Industrial TRON.

The export of these products from Japan is regulated by the Japanese government. The export of some or all of these products may be prohibited without governmental license. To export or re-export some or all of these products from a country other than Japan may also be prohibited without a license from that country. Please call an NEC sales representative.

License not needed:µPD78P083DU The customer must judge the need for license:

PD78081CU-×××, 78081GB-×××-3B4, 78081GB-×××-3BS-MTX

PD78081GB(A)-×××-3B4, 78081GB(A2)-×××-3B4

PD78082CU-×××, 78082GB-×××-3B4, 78082GB-×××-3BS-MTX

PD78082GB(A)-×××-3B4

PD78P083CU, 78P083GB-3B4, 78P083GB-3BS-MTX

PD78P083CU(A), 78P083GB(A)-3B4, 78P083GB(A)-3BS-MTX

The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.

The information in this document is subject to change without notice.

No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated “quality assurance program“ for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application.

Standard: Computers, office equipment, communications equipment, test and measurement equipment,

audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots

Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster

systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support)

Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life

support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product.

M7 96.5

Regional Information

Some information contained in this document may vary from country to country. Before using any NEC product in your application, please contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify:

• Device availability

• Ordering information

• Product release schedule

• Availability of related technical literature

• Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth)

• Network requirements

In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country.

NEC Electronics Inc. (U.S.)

Santa Clara, California Tel: 800-366-9782 Fax: 800-729-9288

NEC Electronics (Germany) GmbH

Duesseldorf, Germany Tel: 0211-65 03 02 Fax: 0211-65 03 490

NEC Electronics (UK) Ltd.

Milton Keynes, UK Tel: 01908-691-133 Fax: 01908-670-290

NEC Electronics Italiana s.r.1.

Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99

NEC Electronics (Germany) GmbH

Benelux Office Eindhoven, The Netherlands Tel:040-2445845 Fax: 040-2444580

NEC Electronics (France) S.A.

Velizy-Villacoublay, France Tel:01-30-67 58 00 Fax: 01-30-67 58 99

NEC Electronics (France) S.A.

Spain Office Madrid, Spain Tel: 01-504-2787 Fax: 01-504-2860

NEC Electronics (Germany) GmbH

Scandinavia Office Taeby, Sweden Tel: 08-63 80 820 Fax: 08-63 80 388

NEC Electronics Hong Kong Ltd.

Hong Kong Tel:2886-9318 Fax: 2886-9022/9044

NEC Electronics Hong Kong Ltd.

Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411

NEC Electronics Singapore Pte. Ltd.

United Square, Singapore 1130 Tel:253-8311 Fax: 250-3583

NEC Electronics Taiwan Ltd.

Taipei, Taiwan Tel: 02-719-2377 Fax: 02-719-5951

NEC do Brasil S.A.

Sao Paulo-SP, Brasil Tel: 011-889-1680 Fax: 011-889-1689

J96. 8

Major Revision in This Edition

Page Description

Throughout The following products have been already developed

PD78081CU-×××, 78081GB-×××-3B4, 78082CU-×××, 78082GB-×××-3B4, 78P083CU, 78P083DU,

78P083GB-3B4 The following products have been added

PD78081GB-×××-3BS-MTX, 78082GB-×××-3BS-MTX, 78P083GB-3BS-MTX, 78081GB(A)-×××-3B4,

78082GB(A)-×××-3B4, 78P083CU(A), 78P083GB(A)-3B4, 78P083GB(A)-3BS-MTX, 78081GB(A2)-×××-3B4

Changes supply voltage to VDD = 1.8 to 5.5V. p. 9 1.6 78K/0 Series Development has been changed. p. 13 1.9 Differences between the µPD78081, 78082, and 78P083, the µPD78081(A), 78082(A), and

78P083(A), and the µPD78081(A2) has been added. p. 19 Cautions regarding the use of functions in common with 2.2.5 (2) (d) ASCK has been added. p. 72 Cautions concerning the Write to OSMS Command has been added to 5.3 (2) Oscillation mode select

p. 73 Cautions concerning external clock input in 5.4.1 Main system clock oscillator has been changed. p. 108 Figure 7-3. Watchdog Timer Mode Register Format, notes and cautions have been added. p. 110 Description of 7.4.2 Interval timer operation has been changed. p. 113 Cautions with regard to rewriting TCL0 to other than same data has been added to 8.3 (1) Timer clock

select register 0 (TCL0). p. 120 The HSC bit has been added to the A/D Converter Mode

Register in Figure10-1. A/D Converter Block Diagram. p. 122, 193 10.3 (1) A/D converter mode register (ADM), 13.1.1 Standby function, and Cautions have been added. p. 137 Figure 11-1. Serial Interface Channel 2 Block Diagram has been corrected. p. 146, 155 11.3 (4) (a), 11.4.2 (1) (d) (i) Generation of baud rate transmit/receive clock by means of main system

clock have been added.

76800 bps has been added to baud rate generated from the main system clock. p. 161 Figure 11-10. Receive Error Timing has been corrected. p. 165 11.4.3 (1) (c) Baud rate generator control register (BRGC) has been added. p. 168 11.4.3 (3) MSB/LSB switching as start bit has been added. p. 206 15.1 Memory Size Switching Register has been changed from W to R/W. p. 205 Items and cautions have been added to Table 15-1. Differences between the µPD78P083 and Mask ROM

Versions. p. 214 A description of the QTOP microcontroller has been added to 15.5 Screening of One-Time PROM

Versions.

p. 232 Figure A-1. Development Tool Configuration has been changed. p. 231 APPENDIX A DEVELOPMENT TOOLS

The following Development Tools have been added:

IE-78000-R-A, IE-70000-98-IF-B, IE-70000-98N-IF, IE-70000-PC-IF-B, IE-78000-R-SV3, SM78K0, ID78K0 p. 239 A.4 OS for IBM PC has been added. p. 240 Table A-2. System-Up Method from Other In-Circuit Emulator to IE-78000-R-A has been added. p. 244 B.1 Real-time OS has been added. p. 249 APPENDIX D REVISION HISTORY has been added.

The mark shows major revised points.

PREFACE

Readers This manual has been prepared for user engineers who want to understand the

functions of the systems and programs.

Caution In the

reliability required for use in customers’ mass-produced equipment. Please use this device only for experimentation or for evaluation of functions.

Purpose This manual is intended for users to understand the functions described in the

Organization below.

Organization The

instruction edition (common to the 78K/0 Series).

PD78083 Subseries, the µPD78P083DU is not designed to maintain the

PD78083 subseries manual is separated into two parts: this manual and the

PD78083 Subseries 78K/0 Series

User’s Manual User’s Manual

(This Manual) Instruction Pin functions CPU functions Internal block functions Instruction set Interrupt Explanation of each instruction Other on-chip peripheral functions

PD78083 subseries and design and develop its application

How to Read This Manual Before reading this manual, you should have general knowledge of electric and logic

circuits and microcontrollers.

For those who will be using this as a manual for the µPD78081(A), 78082(A), 78P083(A) and 78081(A2):

→ The

When you want to understand the functions in general: → Read this manual in the order of the contents. To know the µPD78083 Subseries instruction function in detail: → Refer to the 78K/0 Series User's Manual: Instructions (IEU-1372) How to interpret the register format: →

To learn the function of a register whose register name is known: → Refer to Appendix C Register Index. To know the electrical specifications of the µPD78083 Subseries: → Refer to separately available Data Sheet.

PD78081, 78082, 78P083 are explained as being representative de-

vices.

In case this is used as a manual for the or 78081(A2), please reread the product names as follows.

PD78081 → µPD78081(A) or µPD78081(A2)

PD78082 → µPD78082(A)

PD78P083 → µPD78P083(A)

For the circled bit number, the bit name is defined as a reserved word in RA78K/

0, and in CC78K/0, already defined in the header file named sfrbit.h.

PD78081(A), 78082(A), 78P083(A),

To know application examples of the functions provided in the µPD78083 Subseries: → Refer to Application Note separately provided.

Legend Data representation weight : High digits on the left and low digits on the right

Active low representations : ××× (line over the pin and signal names) Note : Description of note in the text. Caution : Information requiring particular attention Remarks : Additional explanatory material Numeral representations : Binary ... ×××× or ××××B

Decimal ... ×××× Hexadecimal ... ××××H

Examples of use in this manual are prepared for “Standard” quality level devices for general electronic equipment. In the case of examples of use in this manual for devices which meet “Special” quality level requirements, please use each device only after studying each part that is actuall to be used, the circuitry and the quality level of each component before use.

Related Documents The related documents indicated in this publication may include preliminary

versions. However, preliminary versions are not marked as such.

Related documents for µPD78054 subseries

Document name

PD78083 Subseries User’s Manual U12176J This Manual

PD78081, 78082 Data Sheet U11415J U11415E

PD78P083 Data Sheet U11006J U11006E

PD78081(A), 78082(A), 78081(A2) Data Sheet In preparation

PD78P083(A) Data Sheet U12175J U12175E

PD78083 Subseries Special Function Register Table IEM-5599 — 78K/0 Series User’s Manual—Instruction IEU-849 IEU-1372 78K/0 Series Instruction Table U10903J — 78K/0 Series Instruction Set U10904J — 78K/0 Series Application Note Basics (III) IEA-767 U10182E

Document No.

Japanese English

To be prepared

Caution: The above documents are subject to change without prior notice. Be sure to use the latest version

document when starting design.

Development Tool Documents (User’s Manuals)

Document name

RA78K Series Assembler Package Operation EEU-809 EEU-1399

Language EEU-815 EEU-1404 RA78K Series Structured Assembler Preprocessor EEU-817 EEU-1402 RA78K0 Assembler Package Structured assembly language U11789J U11789E

Assembly language U11801J U11801E

Operation U11802J U11802E CC78K Series C Compiler Operation EEU-656 EEU-1280

Language EEU-655 EEU-1284 CC78K/0 C Compiler Operation U11517J U11517E

Language U11518J U11518E CC78K/0 C Compiler Application Note Programming know-how EEA-618 EEA-1208 CC78K Series Library Source File EEU-777 — PG-1500 PROM Programmer U11940J EEU-1335 PG-1500 Controller PC-9800 Series (MS-DOS™) Base EEU-704 EEU-1291 PG-1500 Controller IBM PC Series (PC DOS™) Base EEU-5008 U10540E IE-78000-R EEU-810 U11376E IE-78000-R-A U10057J U10057E IE-78000-R-BK EEU-867 EEU-1427 IE-78078-R-EM U10775J U10775E EP-78083 EEU-5003 EEU-1529 SM78K0 System Simulator Windows™ Base Reference U10181J U10181E SM78K Series System Simulator External component user U10092J U10092E

open interface specifications ID78K0 Integrated Debugger EWS Base Reference U11151J — ID78K0 Integrated Debugger PC Base Reference U11539J — ID78K0 Integrated Debugger Windows™ Base Guide U11649J U11649E SD78K/0 Screen Debugger Introduction EEU-852 U10539E PC-9800 Series (MS-DOS) Base Reference U10952J — SD78K/0 Screen Debugger Introduction EEU-5024 EEU-1414 IBM PC/AT™ (PC DOS) Base Reference U11279J U11279E

Document No.

Japanese English

Caution: The above documents are subject to change without prior notice. Be sure to use the latest version

document when starting design.

Documents for Embedded Software (User’s Manual)

Document name

78K/0 Series Real-Time OS Basics U11537J —

Installation U11536J —

Technicals U11538J — OS for 78K/0 Series MX78K0 Basics EEU-5010 — Fuzzy Knowledge Data Creation Tool EEU-829 EEU-1438 78K/0, 78K/II, 87AD Series Fuzzy Inference Development Support System—Translator EEU-862 EEU-1444 78K/0 Series Fuzzy Inference Development Support System—Fuzzy Inference Module EEU-858 EEU-1441 78K/0 Series Fuzzy Inference Development Support System—Fuzzy Inference Debugger EEU-921 EEU-1458

Document No.

Japanese English

Other Documents

Document name

IC PACKAGE MANUAL C10943X Semiconductor Device Mounting Technology Manual C10535J C10535E Quality Grade on NEC Semiconductor Devices C11531J C11531E Reliability Quality Control on NEC Semiconductor Devices C10983J C10983E Electric Static Discharge (ESD) Test MEM-539 — Semiconductor Devices Quality Assurance Guide C11893J C11893E Microcontroller Related Product Guide—Third Party Manufacturers U11416J —

Document No.

Japanese English

Caution: The above documents are subject to change without prior notice. Be sure to use the latest version

document when starting design.

CONTENTS

CHAPTER 1 OUTLINE..................................................................................................................... 1

1.1 Features ............................................................................................................................. 1

1.2 Applications ...................................................................................................................... 2

1.3 Ordering Information ........................................................................................................ 2

1.4 Quality Grade .................................................................................................................... 3

1.5 Pin Configuration (Top View)........................................................................................... 4

1.6 78K/0 Series Development ............................................................................................... 9

1.7 Block Diagram................................................................................................................... 11

1.8 Outline of Function ........................................................................................................... 12

1.9 Differences between the µPD78081, 78082 and 78P083, the µPD78081(A), 78082(A)

and 78P083(A), and the µPD78081(A2) ........................................................................... 13

CHAPTER 2 PIN FUNCTION ...........................................................................................................15

2.1 Pin Function List ............................................................................................................... 15

2.1.1 Normal operating mode pins ............................................................................................... 15

2.1.2 PROM programming mode pins (

PD78P083 only)............................................................ 16

2.2 Description of Pin Functions ........................................................................................... 17

2.2.1 P00 to P03 (Port 0) .............................................................................................................. 17

2.2.2 P10 to P17 (Port 1) .............................................................................................................. 17

2.2.3 P30 to P37 (Port 3) .............................................................................................................. 18

2.2.4 P50 to P57 (Port 5) .............................................................................................................. 18

2.2.5 P70 to P72 (Port 7) .............................................................................................................. 19

2.2.6 P100 to P101 (Port 10) ........................................................................................................ 19

2.2.7 AV

2.2.8 AV

2.2.9 AV

2.2.10 RESET................................................................................................................................. 20

2.2.11 X1 and X2 ............................................................................................................................ 20

2.2.12 V

2.2.13 V

2.2.14 V

2.2.15 IC (Mask ROM version only)................................................................................................21

2.2.16 NC (44-pin plastic QFP versions only)................................................................................. 21

REF .................................................................................................................................. 20

DD .................................................................................................................................... 20

SS .................................................................................................................................... 20

DD ...................................................................................................................................... 20

SS ...................................................................................................................................... 20

PP (

PD78P083 only)......................................................................................................... 20

2.3 Pin Input/Output Circuits and Recommended Connection of Unused Pins ............... 22

CHAPTER 3 CPU ARCHITECTURE................................................................................................ 25

3.1 Memory Spaces................................................................................................................. 25

3.1.1 Internal program memory space.......................................................................................... 28

3.1.2 Internal data memory space ................................................................................................ 29

3.1.3 Special Function Register (SFR) area ................................................................................. 29

3.1.4 Data memory addressing .................................................................................................... 29

3.2 Processor Registers ......................................................................................................... 33

3.2.1 Control registers .................................................................................................................. 33

3.2.2 General registers ................................................................................................................. 36

– i –

3.2.3 Special Function Register (SFR) ......................................................................................... 37

3.3 Instruction Address Addressing ..................................................................................... 40

3.3.1 Relative Addressing ............................................................................................................. 40

3.3.2 Immediate addressing ......................................................................................................... 41

3.3.3 Table indirect addressing..................................................................................................... 42

3.3.4 Register addressing............................................................................................................. 43

3.4 Operand Address Addressing ......................................................................................... 44

3.4.1 Implied addressing .............................................................................................................. 44

3.4.2 Register addressing............................................................................................................. 45

3.4.3 Direct addressing................................................................................................................. 46

3.4.4 Short direct addressing........................................................................................................ 47

3.4.5 Special-Function Register (SFR) addressing ...................................................................... 49

3.4.6 Register indirect addressing ................................................................................................ 50

3.4.7 Based addressing ................................................................................................................ 51

3.4.8 Based indexed addressing .................................................................................................. 52

3.4.9 Stack addressing ................................................................................................................. 52

CHAPTER 4 PORT FUNCTIONS .................................................................................................... 53

4.1 Port Functions................................................................................................................... 53

4.2 Port Configuration ............................................................................................................ 55

4.2.1 Port 0 ................................................................................................................................... 55

4.2.2 Port 1 ................................................................................................................................... 57

4.2.3 Port 3 ................................................................................................................................... 58

4.2.4 Port 5 ................................................................................................................................... 59

4.2.5 Port 7 ................................................................................................................................... 60

4.2.6 Port 10 ................................................................................................................................. 62

4.3 Port Function Control Registers ..................................................................................... 63

4.4 Port Function Operations................................................................................................. 67

4.4.1 Writing to input/output port................................................................................................... 67

4.4.2 Reading from input/output port ............................................................................................ 67

4.4.3 Operations on input/output port ........................................................................................... 67

CHAPTER 5 CLOCK GENERATOR................................................................................................ 69

5.1 Clock Generator Functions .............................................................................................. 69

5.2 Clock Generator Configuration ....................................................................................... 69

5.3 Clock Generator Control Register ................................................................................... 71

5.4 System Clock Oscillator................................................................................................... 73

5.4.1 Main system clock oscillator ................................................................................................ 73

5.4.2 Scaler................................................................................................................................... 75

5.5 Clock Generator Operations ............................................................................................ 76

5.6 Changing CPU Clock Settings ......................................................................................... 77

5.6.1 Time required for CPU clock switchover.............................................................................. 77

5.6.2 CPU clock switching procedure ........................................................................................... 78

CHAPTER 6 8-BIT TIMER/EVENT COUNTERS 5 AND 6 .............................................................. 79

6.1 8-Bit Timer/Event Counters 5 and 6 Functions .............................................................. 80

6.2 8-Bit Timer/Event Counters 5 and 6 Configurations...................................................... 82

6.3 8-Bit Timer/Event Counters 5 and 6 Control Registers ................................................. 84

– ii –

6.4 8-Bit Timer/Event Counters 5 and 6 Operations ............................................................ 90

6.4.1 Interval timer operations ...................................................................................................... 90

6.4.2 External event counter operation......................................................................................... 93

6.4.3 Square-wave output ............................................................................................................ 94

6.4.4 PWM output operations ....................................................................................................... 96

6.5 Cautions on 8-Bit Timer/Event Counters 5 and 6 .......................................................... 100

CHAPTER 7 WATCHDOG TIMER................................................................................................... 103

7.1 Watchdog Timer Functions.............................................................................................. 103

7.2 Watchdog Timer Configuration ....................................................................................... 105

7.3 Watchdog Timer Control Registers................................................................................. 106

7.4 Watchdog Timer Operations ............................................................................................ 109

7.4.1 Watchdog timer operation.................................................................................................... 109

7.4.2 Interval timer operation ........................................................................................................ 110

CHAPTER 8 CLOCK OUTPUT CONTROL CIRCUIT ..................................................................... 1 11

8.1 Clock Output Control Circuit Functions ......................................................................... 111

8.2 Clock Output Control Circuit Configuration................................................................... 112

8.3 Clock Output Function Control Registers ...................................................................... 113

CHAPTER 9 BUZZER OUTPUT CONTROL CIRCUIT .................................................................... 115

9.1 Buzzer Output Control Circuit Functions ....................................................................... 115

9.2 Buzzer Output Control Circuit Configuration................................................................. 115

9.3 Buzzer Output Function Control Registers .................................................................... 116

CHAPTER 10 A/D CONVERTER....................................................................................................... 119

10.1 A/D Converter Functions.................................................................................................. 119

10.2 A/D Converter Configuration ........................................................................................... 119

10.3 A/D Converter Control Registers..................................................................................... 122

10.4 A/D Converter Operations................................................................................................ 126

10.4.1 Basic operations of A/D converter ....................................................................................... 126

10.4.2 Input voltage and conversion results ................................................................................... 128

10.4.3 A/D converter operating mode............................................................................................. 129

10.5 A/D Converter Cautions ................................................................................................... 131

CHAPTER 11 SERIAL INTERFACE CHANNEL 2 ............................................................................ 135

11.1 Serial Interface Channel 2 Functions.............................................................................. 135

11.2 Serial Interface Channel 2 Configuration ....................................................................... 136

11.3 Serial Interface Channel 2 Control Registers................................................................. 140

11.4 Serial Interface Channel 2 Operation .............................................................................. 148

11.4.1 Operation stop mode ........................................................................................................... 148

11.4.2 Asynchronous serial interface (UART) mode ...................................................................... 150

11.4.3 3-wire serial I/O mode ......................................................................................................... 163

CHAPTER 12 INTERRUPT FUNCTION ............................................................................................ 171

12.1 Interrupt Function Types.................................................................................................. 171

12.2 Interrupt Sources and Configuration .............................................................................. 172

12.3 Interrupt Function Control Registers.............................................................................. 175

– iii –

12.4 Interrupt Servicing Operations ........................................................................................ 181

12.4.1 Non-maskable interrupt request acknowledge operation .................................................... 181

12.4.2 Maskable interrupt request acknowledge operation ............................................................ 184

12.4.3 Software interrupt request acknowledge operation ............................................................. 187

12.4.4 Multiple interrupt servicing ................................................................................................... 187

12.4.5 Interrupt request reserve ..................................................................................................... 191

CHAPTER 13 STANDBY FUNCTION................................................................................................ 193

13.1 Standby Function and Configuration.............................................................................. 193

13.1.1 Standby function .................................................................................................................. 193

13.1.2 Standby function control register ......................................................................................... 194

13.2 Standby Function Operations.......................................................................................... 195

13.2.1 HALT mode.......................................................................................................................... 195

13.2.2 STOP mode ......................................................................................................................... 198

CHAPTER 14 RESET FUNCTION..................................................................................................... 201

14.1 Reset Function .................................................................................................................. 201

CHAPTER 15µPD78P083 ................................................................................................................. 205

15.1 Memory Size Switching Register..................................................................................... 206

15.2 PROM Programming......................................................................................................... 207

15.2.1 Operating modes ................................................................................................................. 207

15.2.2 PROM write procedure ........................................................................................................ 209

15.2.3 PROM reading procedure.................................................................................................... 213

15.3 Erasure Procedure (µPD78P083DU Only)....................................................................... 214

15.4 Opaque Film Masking the Window (µPD78P083DU Only)............................................. 214

15.5 Screening of One-Time PROM Versions......................................................................... 214

CHAPTER 16 INSTRUCTION SET .................................................................................................... 215

16.1 Legends Used in Operation List...................................................................................... 216

16.1.1 Operand identifiers and description methods ...................................................................... 216

16.1.2 Description of “operation” column........................................................................................ 217

16.1.3 Description of “flag operation” column ................................................................................. 217

16.2 Operation List.................................................................................................................... 218

16.3 Instructions Listed by Addressing Type......................................................................... 226

APPENDIX A DEVELOPMENT TOOLS............................................................................................ 231

A.1 Language Processing Software ...................................................................................... 233

A.2 PROM Programming Tools .............................................................................................. 234

A.2.1 Hardware ............................................................................................................................. 234

A.2.2 Software............................................................................................................................... 234

A.3 Debugging Tools............................................................................................................... 235

A.3.1 Hardware ............................................................................................................................. 235

A.3.2 Software (1/3) ...................................................................................................................... 236

A.3.2 Software (2/3) ...................................................................................................................... 237

A.3.2 Software (3/3) ...................................................................................................................... 238

A.4 OS for IBM PC ................................................................................................................... 239

– iv –

A.5 System-Upgrade Method from Other In-Circuit Emulators to 78K/0 Series

In-Circuit Emulator............................................................................................................ 240

APPENDIX B EMBEDDED SOFTWARE .......................................................................................... 243

B.1 Real-time OS...................................................................................................................... 244

B.2 Fuzzy Inference Development Support System............................................................. 245

APPENDIX C REGISTER INDEX ...................................................................................................... 247

C.1 Register Index ..................................................................................................................... 247

APPENDIX D REVISION HISTORY .................................................................................................. 249

– v –

FIGURE (1/4)

Fig. No. Title Page

2-1 Pin Input/Output Circuit of List............................................................................................ 23

3-1 Memory Map ( 3-2 Memory Map ( 3-3 Memory Map ( 3-4 Data Memory Addressing ( 3-5 Data Memory Addressing ( 3-6 Data Memory Addressing (

3-7 Program Counter Configuration ......................................................................................... 33

3-8 Program Status Word Configuration................................................................................... 33

3-9 Stack Pointer Configuration................................................................................................ 35

3-10 Data to be Saved to Stack Memory.................................................................................... 35

3-11 Data to be Reset from Stack Memory ................................................................................ 35

3-12 General Register Configuration .......................................................................................... 36

4-1 Port Types .......................................................................................................................... 53

4-2 P00 Block Diagram............................................................................................................. 56

4-3 P01 to P03 Block Diagram ................................................................................................. 56

4-4 P10 to P17 Block Diagram ................................................................................................. 57

4-5 P30 to P37 Block Diagram ................................................................................................. 58

4-6 P50 to P57 Block Diagram ................................................................................................. 59

4-7 P70 Block Diagram............................................................................................................. 60

4-8 P71 and P72 Block Diagram .............................................................................................. 61

4-9 P100 to P101 Block Diagram ............................................................................................. 62

4-10 Port Mode Register Format ................................................................................................ 65

4-11 Pull-Up Resistor Option Register Format ........................................................................... 66

PD78081) .................................................................................................. 25

PD78082) .................................................................................................. 26

PD78P083)................................................................................................ 27

PD78081)............................................................................... 30

PD78082)............................................................................... 31

PD78P083) ............................................................................ 32

5-1 Block Diagram of Clock Generator..................................................................................... 70

5-2 Processor Clock Control Register Format.......................................................................... 71

5-3 Oscillation Mode Selection Register Format ...................................................................... 72

5-4 Main System Clock Waveform due to Writing to OSMS.....................................................

5-5 External Circuit of Main System Clock Oscillator ............................................................... 73

5-6 Examples of Oscillator with Bad Connection (1/2) ............................................................. 74

5-7 CPU Clock Switching ......................................................................................................... 78

6-1 8-Bit Timer/Event Counters 5 and 6 Block Diagram ........................................................... 82

6-2 Block Diagram of 8-Bit Timer/Event Counters 5 and 6 Output Control Circuit ................... 83

6-3 Timer Clock Select Register 5 Format................................................................................ 85

6-4 Timer Clock Select Register 6 Format................................................................................ 86

6-5 8-Bit Timer Mode Control Register 5 Format...................................................................... 87

6-6 8-Bit Timer Mode Control Register 6 Format...................................................................... 88

6-7 Port Mode Register 10 Format ........................................................................................... 89

6-8 8-Bit Timer Mode Control Register Settings for Interval Timer Operation .......................... 90

6-9 Interval Timer Operation Timings ....................................................................................... 91

– vi –

FIGURE (2/4)

Fig. No. Title Page

6-10 8-Bit Timer Mode Control Register Setting for External Event Counter Operation............. 93

6-11 External Event Counter Operation Timings (with Rising Edge Specification) .................... 93

6-12 8-Bit Timer Mode Control Register Settings for Square-Wave Output Operation .............. 94

6-13 8-Bit Timer Mode Control Register Settings for PWM Output Operation ........................... 96

6-14 PWM Output Operation Timing (Active high setting).......................................................... 97

6-15 PWM Output Operation Timings (CRn0 = 00H, active high setting)................................... 97

6-16 PWM Output Operation Timings (CRn0 = FFH, active high setting) .................................. 98

6-17 PWM Output Operation Timings (CRn0 changing, active high setting).............................. 99

6-18 8-Bit Timer Registers 5 and 6 Start Timing......................................................................... 100

6-19 External Event Counter Operation Timing.......................................................................... 100

6-20 Timing after Compare Register Change during Timer Count Operation ............................ 101

7-1 Watchdog Timer Block Diagram ......................................................................................... 105

7-2 Timer Clock Select Register 2 Format................................................................................ 107

7-3 Watchdog Timer Mode Register Format............................................................................. 108

8-1 Remote Controlled Output Application Example ................................................................ 111

8-2 Clock Output Control Circuit Block Diagram....................................................................... 112

8-3 Timer Clock Select Register 0 Format................................................................................ 113

8-4 Port Mode Register 3 Format ............................................................................................. 114

9-1 Buzzer Output Control Circuit Block Diagram .................................................................... 115

9-2 Timer Clock Select Register 2 Format................................................................................ 117

9-3 Port Mode Register 3 Format ............................................................................................. 118

10-1 A/D Converter Block Diagram ............................................................................................ 120

10-2 A/D Converter Mode Register Format ................................................................................ 123

10-3 A/D Converter Input Select Register Format ...................................................................... 124

10-4 External Interrupt Mode Register 1 Format ........................................................................ 125

10-5 A/D Converter Basic Operation .......................................................................................... 127

10-6 Relations between Analog Input Voltage and A/D Conversion Result................................ 128

10-7 A/D Conversion by Hardware Start .................................................................................... 129

10-8 A/D Conversion by Software Start...................................................................................... 130

10-9 Example of Method of Reducing Current Dissipation in Standby Mode............................. 131

10-10 Analog Input Pin Disposition .............................................................................................. 132

10-11 A/D Conversion End Interrupt Request Generation ...........................................................

10-12 Handling of AVDD Pin......................................................................................................... 133

11-1 Serial Interface Channel 2 Block Diagram ......................................................................... 137

11-2 Baud Rate Generator Block Diagram ................................................................................. 138

11-3 Serial Operating Mode Register 2 Format.......................................................................... 140

11-4 Asynchronous Serial Interface Mode Register Format....................................................... 141

11-5 Asynchronous Serial Interface Status Register Format ..................................................... 143

11-6 Baud Rate Generator Control Register Format (1/2) ......................................................... 144

– vii –

FIGURE (3/4)

Fig. No. Title Page

11-6 Baud Rate Generator Control Register Format (2/2) ......................................................... 145

11-7 Asynchronous Serial Interface Transmit/Receive Data Format.......................................... 157

11-8 Asynchronous Serial Interface Transmission Completion Interrupt Request Timing.......... 159

11-9 Asynchronous Serial Interface Reception Completion Interrupt Request Timing............... 160

11-10 Receive Error Timing.......................................................................................................... 161

11-11 State of the Receive Buffer Register (RXB) when Reception is Interrupted, and

Generation/Non Generation of an Interrupt Request (INTSR) ........................................... 162

11-12 3-Wire serial I/O Mode Timing............................................................................................ 168

11-13 Circuit of Switching in Transfer Bit Order ........................................................................... 169

12-1 Basic Configuration of Interrupt Function (1/2)................................................................... 173

12-1 Basic Configuration of Interrupt Function (2/2)................................................................... 174

12-2 Interrupt Request Flag Register Format ............................................................................. 176

12-3 Interrupt Mask Flag Register Format.................................................................................. 177

12-4 Priority Specify Flag Register Format................................................................................. 178

12-5 External Interrupt Mode Register 0 Format ........................................................................ 179

12-6 External Interrupt Mode Register 1 Format ........................................................................ 179

12-7 Program Status Word Configuration................................................................................... 180

12-8 Flowchart from Non-Maskable Interrupt Request Generation to Acknowledgment............ 182

12-9 Non-Maskable Interrupt Request Acknowledge Timing ...................................................... 182

12-10 Non-Maskable Interrupt Request Acknowledge Operation ................................................ 183

12-11 Interrupt Request Acknowledge Processing Algorithm ....................................................... 185

12-12 Interrupt Request Acknowledge Timing (Minimum Time) ................................................... 186

12-13 Interrupt Request Acknowledge Timing (Maximum Time) .................................................. 186

12-14 Example of Multiple Interrupt (1/2) ..................................................................................... 189

12-14 Example of Multiple Interrupt (2/2) ..................................................................................... 190

12-15 Interrupt Request Hold ....................................................................................................... 192

13-1 Oscillation Stabilization Time Select Register Format........................................................ 194

13-2 HALT Mode Clear upon Interrupt Generation ..................................................................... 196

13-3 HALT Mode Release by RESET Input ................................................................................ 197

13-4 STOP Mode Release by Interrupt Generation.................................................................... 199

13-5 Release by STOP Mode RESET Input............................................................................... 200

14-1 Block Diagram of Reset Function ....................................................................................... 201

14-2 Timing of Reset Input by RESET Input............................................................................... 202

14-3 Timing of Reset due to Watchdog Timer Overflow ............................................................. 202

14-4 Timing of Reset Input in STOP Mode by RESET Input ...................................................... 202

15-1 Memory Size Switching Register Format ........................................................................... 206

15-2 Page Program Mode Flowchart.......................................................................................... 209

15-3 Page Program Mode Timing............................................................................................... 210

15-4 Byte Program Mode Flowchart ........................................................................................... 211

15-5 Byte Program Mode Timing................................................................................................ 212

– viii –

FIGURE (4/4)

Fig. No. Title Page

15-6 PROM Read Timing ........................................................................................................... 213

A-1 Development Tool Configuration ........................................................................................ 232

A-2 EV-9200G-44 Drawing (For Reference Only)..................................................................... 241

A-3 EV-9200G-44 Footprint (For Reference Only).................................................................... 242

– ix –

TABLE (1/2)

Table. No. Title Page

1-1 Differences between the µPD78081, 78082 and 78P083, the µPD78081(A), 78082(A)

and 78P083(A), and the

2-1 Type of Input/Output Circuit of Each Pin ............................................................................ 22

3-1 Vector Table ........................................................................................................................ 28

3-2 Special-Function Register List (1/2) .................................................................................. 38

3-2 Special-Function Register List (2/2) ................................................................................... 39

4-1 Port Functions .................................................................................................................... 54

4-2 Port Configuration .............................................................................................................. 55

4-3 Port Mode Register and Output Latch Settings when Using Dual-Fucntions..................... 64

5-1 Clock Generator Configuration........................................................................................... 69

5-2 Maximum Time Required for CPU Clock Switchover ......................................................... 77

6-1 Timer/Event Counter Types and Functions ........................................................................ 79

6-2 8-Bit Timer/Event Counters 5 and 6 Interval Times............................................................ 80

6-3 8-Bit Timer/Event Counters 5 and 6 Square-Wave Output Ranges ................................... 81

6-4 8-Bit Timer/Event Counters 5 and 6 Configurations ........................................................... 82

6-5 8-Bit Timer/Event Counters 5 and 6 Interval Times............................................................ 92

6-6 8-Bit Timer/Event Counters 5 and 6 Square-Wave Output Ranges ................................... 95

PD78081(A2) ............................................................................ 13

7-1 Watchdog Timer Overrun Detection Times ......................................................................... 103

7-2 Interval Times ..................................................................................................................... 104

7-3 Watchdog Timer Configuration ........................................................................................... 105

7-4 Watchdog Timer Overrun Detection Time .......................................................................... 109

7-5 Interval Timer Interval Time ................................................................................................ 110

8-1 Clock Output Control Circuit Configuration ........................................................................ 112

9-1 Buzzer Output Control Circuit Configuration ...................................................................... 115

10-1 A/D Converter Configuration .............................................................................................. 119

11-1 Serial Interface Channel 2 Configuration ........................................................................... 136

11-2 Serial Interface Channel 2 Operating Mode Settings ......................................................... 142

11-3 Relation between Main System Clock and Baud Rate ....................................................... 146

11-4 Relation between ASCK Pin Input Frequency and Baud Rate (When BRGC is set to 00H) 147

11-5 Relation between Main System Clock and Baud Rate ....................................................... 155

11-6 Relation between ASCK Pin Input Frequency and Baud Rate (When BRGC is set to 00H) 156

11-7 Receive Error Causes ........................................................................................................ 161

– x –

TABLE (2/2)

Table. No. Title Page

12-1 Interrupt Source List ........................................................................................................... 172

12-2 Various Flags Corresponding to Interrupt Request Sources .............................................. 175

12-3 Times from Maskable Interrupt Request Generation to Interrupt Service .......................... 184

12-4 Interrupt Request Enabled for Multiple Interrupt during Interrupt Servicing ....................... 188

13-1 HALT Mode Operating Status ............................................................................................. 195

13-2 Operation after HALT Mode Release ................................................................................. 197

13-3 STOP Mode Operating Status............................................................................................ 198

13-4 Operation after STOP Mode Release................................................................................. 200

14-1 Hardware Status after Reset (1/2)...................................................................................... 203

14-1 Hardware Status after Reset (2/2)...................................................................................... 204

15-1 Differences between the

15-2 Examples of Memory Size Switching Register Settings ..................................................... 206

15-3 PROM Programming Operating Modes ............................................................................. 207

PD78P083 and Mask ROM Versions ....................................... 205

16-1 Operand Identifiers and Description Methods .................................................................... 216

A-1 System-Up Method from Other In-Circuit Emulator to IE-78000-R .................................... 240

A-2 System-Up Method from Other In-Circuit Emulator to IE-78000-R-A................................. 240

– xi –

[MEMO]

– xii –

1.1 Features

On-chip ROM and RAM

CHAPTER 1 OUTLINE

Part Number

PD78081

PD78082

PD78P083

Type

Program Memory

(ROM)

8 Kbytes 16 Kbytes

(

24 Kbytes

Note

)

Data Memory

(Internal High-Speed RAM)

256 bytes 384 bytes

512 bytes

(

Note

)

Note The capacities of internal PROM and internal high-speed RAM can be changed by means of the memory

size switching register (IMS).

Instruction execution time changeable from high speed (0.4 µs: In main system clock 5.0 MHz operation) to low

speed (12.8

s: In main system clock 5.0 MHz operation)

Instruction set suited to system control

• Bit manipulation possible in all address spaces

• Multiply and divide instructions 33 I/O ports 8-bit resolution A/D converter: 8 channels Serial interface: 1 channel

• 3-wire serial I/O/UART mode: 1 channel Timer: 3 channels

• 8-bit timer/event counter : 2 channels

• Watchdog timer : 1 channel Vectored Interrupt Source : 13 Supply voltage: VDD = 1.8 to 5.5 V

CHAPTER 1 OUTLINE

1.2 Applications

PD78081, 78082, 78P083:

Airbags, CRT displays, keyboards, air conditioners, hot water dispensers, boilers, fan heaters, dashboards, etc.

PD78081(A), 78082(A), 78P083(A), 78081(A2):

Automobile electrical control devices, gas detector cutoff devices, various safety devices, etc.

1.3 Ordering Information

Part number Package Internal ROM

PD78081CU-××× 42-pin plastic shrink DIP (600 mil) Mask ROM

PD78081GB-×××-3B4 44-pin plastic QFP (10 × 10 mm) Mask ROM

PD78081GB-×××-3BS-MTX 44-pin plastic QFP (10 × 10 mm) Mask ROM

PD78082CU-××× 42-pin plastic shrink DIP (600 mil) Mask ROM

PD78082GB-×××-3B4 44-pin plastic QFP (10 × 10 mm) Mask ROM

PD78082GB-×××-3BS-MTX 44-pin plastic QFP (10 × 10 mm) Mask ROM

PD78P083CU 42-pin plastic shrink DIP (600 mil) One-Time PROM

PD78P083DU 42-pin ceramic shrink DIP (with window) (600 mil) EPROM

PD78P083GB-3B4 44-pin plastic QFP (10 × 10 mm) One-Time PROM

PD78P083GB-3BS-MTX 44-pin plastic QFP (10 × 10 mm) One-Time PROM

PD78081GB(A)-×××-3B4 44-pin plastic QFP (10 × 10 mm) Mask ROM

PD78082GB(A)-×××-3B4 44-pin plastic QFP (10 × 10 mm) Mask ROM

PD78P083CU(A) 42-pin plastic shrink DIP (600 mil) One-Time PROM

PD78P083GB(A)-3B4 44-pin plastic QFP (10 × 10 mm) One-Time PROM

PD78P083GB(A)-3BS-MTX

PD78081GB(A2)-×××-3B4 44-pin plastic QFP (10 × 10 mm) Mask ROM

Note

44-pin plastic QFP (10 × 10 mm) One-Time PROM

Note Under development

Remark ××× indicates ROM code suffix.

CHAPTER 1 OUTLINE

1.4 Quality Grade

Part number Package Quality grade

PD78081CU-××× 42-pin plastic shrink DIP (600 mil) Standard

PD78081GB-×××-3B4 44-pin plastic QFP (10 × 10 mm) Standard

PD78081GB-×××-3BS-MTX 44-pin plastic QFP (10 × 10 mm) Standard

PD78082CU-××× 42-pin plastic shrink DIP (600 mil) Standard

PD78082GB-×××-3B4 44-pin plastic QFP (10 × 10 mm) Standard

PD78082GB-×××-3BS-MTX 44-pin plastic QFP (10 × 10 mm) Standard

PD78P083CU 42-pin plastic shrink DIP (600 mil) Standard

PD78P083DU 42-pin ceramic shrink DIP (with window) (600 mil) Not applicable

PD78P083GB-3B4 44-pin plastic QFP (10 × 10 mm) Standard

PD78P083GB-3BS-MTX 44-pin plastic QFP (10 × 10 mm) Standard

PD78081GB(A)-×××-3B4 44-pin plastic QFP (10 × 10 mm) Special

PD78082GB(A)-×××-3B4 44-pin plastic QFP (10 × 10 mm) Special

PD78P083CU(A) 42-pin plastic shrink DIP (600 mil) Special

PD78P083GB(A)-3B4 44-pin plastic QFP (10 × 10 mm) Special

PD78P083GB(A)-3BS-MTX

PD78081GB(A)-×××-3B4 44-pin plastic QFP (10 × 10 mm) Special

Note

44-pin plastic QFP (10 × 10 mm) Special

Note Under planning

Remark ××× indicates ROM code suffix.

Please refer to “Quality grade on NEC Semiconductor Devices” (Document number C11531E) published by NEC Corporation to know the specification of quality grade on the devices and its recommended applications.

1.5 Pin Configuration (Top View)

(1) Normal operating mode

42-pin plastic shrink DIP (600 mil)

PD78081CU-×××, 78082CU-×××, 78P083CU, 78P083CU(A)

42-pin ceramic shrink DIP (with window) (600 mil)

PD78P083DU

CHAPTER 1 OUTLINE

P55 P56 P57 P30 P31 P32 P33

P34 P35/PCL P36/BUZ

P37

P00

P01/INTP1 P02/INTP2 P03/INTP3

RESET

IC (V

PP)

X2 X1

AVDD

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

20 21

42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22

P54 P53 P52 P51 P50 P100/TI5/TO5 P101/TI6/TO6 P70/R

XD/SI2

P71/T

XD/SO2

P72/ASCK/SCK2 P17/ANI7 P16/ANI6 P15/ANI5 P14/ANI4 P13/ANI3 P12/ANI2 P11/ANI1 P10/ANI0 AV

AVREF

Cautions 1. Be sure to connect IC (Internally Connected) pin to VSS directly.

2. Connect AV

3. Connect AV

DD pin to VDD. SS pin to VSS.

Remark Pin connection in parentheses is intended for the

PD78P083.

CHAPTER 1 OUTLINE

• 44-pin plastic QFP (10 × 10 mm)

PD78081GB-×××-3B4, 78081GB-×××-3BS-MTX

PD78082GB-×××-3B4, 78082GB-×××-3BS-MTX

PD78P083GB-3B4, 78P083GB-3BS-MTX

PD78081GB(A)-×××-3B4, 78082GB(A)-×××-3B4

PD78P083GB(A)-3B4, 78P083GB(A)-3BS-MTX

PD78P081GB(A2)-×××-3B4

P11/ANI1

P10/ANI0

AVSS

AVREF

Note

AVDD

VDDX1X2

IC (VPP)

RESET

P12/ANI2 P13/ANI3 P14/ANI4 P15/ANI5 P16/ANI6 P17/ANI7

P72/ASCK/SCK2

P71/TxD/SO2

P70/RxD/SI2 P101/TI6/TO6 P100/TI5/TO6

44 43 42 41 40 39 38 37 36 35 34

1 2 3 4 5 6 7 8 9 10 11

12 13 14 15 16 17 18 19 20 21 22

VSS

P55

P56

P50

P51

P52

P53

P54

P57

P30

33 32 31 30 29 28 27 26 25 24 23

P31

Note Under development

Cautions 1. Be sure to connect IC (Internally Connected) pin to V

2. Connect AV

3. Connect AV

4. Connect NC pin to V

DD pin to VDD. SS pin to VSS.

SS for noise protection (It can be left open).

P03/INTP3 P02/INTP2 P01/INTP1 P00 P37 P36/BUZ P35/PCL P34 P33 P32 NC

SS directly.

Remark Pin connection in parenthesis is intended for the

PD78P083.

CHAPTER 1 OUTLINE

Pin Identifications

ANI0 to ANI7 : Analog Input P100, P101 : Port 10 ASCK : Asynchronous Serial Clock PCL : Programmable Clock

DD : Analog Power Supply RESET : Reset

REF : Analog Reference Voltage RxD : Receive Data

SS : Analog Ground SCK2 : Serial Clock

AV BUZ : Buzzer Clock SI2 : Serial Input IC : Internally Connected SO2 : Serial Output INTP1 to INTP3 : Interrupt from Peripherals TI5, TI6 : Timer Input NC : Non-connection TO5 to TO6 : Timer Output P00 to P03 : Port 0 TxD : Transmit Data P10 to P17 : Port 1 V P30 to P37 : Port 3 V P50 to P57 : Port 5 V P70 to P72 : Port 7 X1, X2 : Crystal (Main System Clock)

DD : Power Supply PP : Programming Power Supply SS : Ground

CHAPTER 1 OUTLINE

(2) PROM programming mode

• 42-pin plastic shrink DIP (600 mil)

PD78P083CU, 78P083CU(A)

• 42-pin ceramic shrink DIP (with window) (600 mil)

PD78P083DU

A5 A6

A7 OE CE

PGM

1 2 3 4 5 6 7 8

(L)

9 10 11

12 13

(L)

14 15

RESET

Open

(L)

V VDD

16 17 18 19 20 21

Cautions 1. (L) : Individually connect to V

SS : Connect to the ground.

2. V

3. RESET: Set to the low level.

4. Open : Do not connect anything.

42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22

SS via a pull-down resistor.

A4 A3 A2 A1 A0 A10 A11 A12 A13 A14 D7 D6 D5 D4 D3 D2 D1 D0 V

VSS

CHAPTER 1 OUTLINE

• 44-pin plastic QFP (10 × 10 mm)

PD78P083GB-3B4, 78P083GB-3BS-MTX

PD78P083GB(A)-3B4, 78P083GB(A)-3BS-MTX

Note

D2 D3 D4 D5 D6

D7 A14 A13 A12 A11 A10

D1D0VSS

44 43 42 41 40 39 38 37 36 35 34

1 2 3 4 5 6 7 8 9 10 11

12 13 14 15 16 17 18 19 20 21 22

A0A1A2A3A4

VSS

VDD

VSS

Note Under development

Cautions 1. (L) : Connect individually to V

SS : Connect to the ground.

2. V

3. RESET : Set to the low level.

4. Open : Do not connect anything.

(L)

Open

VPP

RESET

(L)

33 32 31 30 29 28 27 26 25 24 23

A5A6A7

SS via a pull-down resistor.

(L)

A8 PGM (L)

A0 to A14 : Address Bus RESET : Reset CE : Chip Enable V D0 to D7 : Data Bus V OE : Output Enable V

DD : Power Supply PP : Programming Power Supply SS : Ground

PGM : Program

CHAPTER 1 OUTLINE

100-pin 100-pin 100-pin 100-pin 80-pin 80-pin 80-pin 64-pin 64-pin 64-pin 64-pin 64-pin 64-pin 64-pin 42/44-pin

100-pin 100-pin 80-pin 80-pin

100-pin 100-pin 100-pin

µPD780308Y

µPD78064Y

80-pin

78K/0 series

Control

FIP® driving

IEBus

supported

Low EMI noise version of the µPD78078 Timer is added to the µPD78054 and its external interface is enhanced. ROM-less versions of the µPD78078 Serial I/O of the µPD78078 is enhanced and only selected functions are provided. Serial I/O-enhanced versions of the µPD78054; Low EMI noise version Low EMI noise version of the µPD78054 UART and D/A converter are added to the µPD78014 and I/O is enhanced

. A/D-enhanced version of the µPD780024 Serial I/O-enhanced versions of the µPD78018F; Low EMI noise version Low EMI noise version of the µPD78018F Low-voltage (1.8 V) operation versions of the µPD78014 with several ROM and RAM capacities available. A/D converter and 16-bit timer are added to the µPD78002. A/D converter is added to the µPD78002. Basic subseries for control applications On-chip UART, and operable at low voltage (1.8 V).

I/O and FIP C/D of the µPD78044F are enhanced. Total display outputs : 53 pins I/O and FIP C/D of the µPD78044H are enhanced. Total display outputs : 48 pins N-ch open-drain I/O is added to the µPD78044F. Total display outputs : 34 pins Basic subseries for FIP driving. Total display outputs: 34 pins

SIO of the µPD78064 is enhanced, and ROM and RAM are expanded. Low EMI noise version of the µPD78064 Basic subseries for driving LCDs and with on-chip UART.

IEBus controller is added to the µPD78054.

Mass-produced products Products under development

Y Subseries supports the I

C bus specifications.

µPD78098

64-pin

PWM output, LV digital code decoder and Hsync counter are incorporated.

µPD78P0914

µPD780308

64-pin 64-pin

Inverter control

A/D-enhanced version of the µPD780924 On-chip inverter control circuit and UART incorporated; Low EMI noise version

µPD780964 µPD780924

LCD driving

µPD78064B µPD78064

µPD780208

µPD780228 µPD78044H µPD78044F

µPD78075B

µPD78078

µPD78070A

µPD780018

Note

µPD780058

µPD78058F

µPD78054 µPD780034 µPD780024

µPD78014H

µPD78018F

µPD78014 µPD780001

µPD78002

µPD78083

µPD78075BY

µPD78078Y

µPD78070AY

µPD780018Y

Note

µPD780058Y

Note

µPD78058FY

µPD78054Y µPD780034Y µPD780024Y

µPD78018FY

µPD78014Y

µPD78002Y

1.6 78K/0 Series Development

The following shows the 78K/0 Series products development. Subseries names are shown inside frames.

Note Under planning

CHAPTER 1 OUTLINE

The following table shows the differences among subseries functions.

Function ROM Timer 8-bit Subseries name capacity 8-bit Control

PD78075B 32K to 40K 4 ch 1 ch 1 ch 1 ch 8 ch — 2 ch

PD78078 48K to 60K

PD78070A — 61 2.7 V

PD780018 48K to 60K —

PD780058 24K to 60K 2 ch 2 ch

PD78058F 48K to 60K

PD78054 16K to 60K 2.0 V

PD780034 8K to 32K — 8 ch —

PD780024 8 ch —

PD78014H 2 ch 53

PD78018F 8K to 60K

PD78014 8K to 32K 2.7 V

PD780001 8K — — 1 ch 39 —

16-bit Watch

WDT

A/D A/D D/A

10-bit

8-bit

Serial interface I/O

3 ch (UART: 1 ch)

2 ch (Time division 3-wire: 1 ch)

3 ch (Time division UART: 1 ch)

3 ch (UART: 1 ch)

3 ch (UART: 1 ch, Time division 3-wire: 1 ch)

VDD

MIN.

value

88 1.8 V Available

68 1.8 V

69 2.7 V

51 1.8 V

External

expansion

PD78002 8K to 16K 1 ch — 53 Available

PD78083 — 8 ch

Inverter control

FIP driving

LCD driving

IEBus supported

PD780964 8K to 32K 3 ch Note —1 ch—8 ch—

PD780924 8 ch —

PD780208 32K to 60K 2 ch 1 ch 1 ch 1 ch 8 ch — — 2 ch 74 2.7 V —

PD780228 48K to 60K 3 ch — — 1 ch 72 4.5 V

PD78044H 32K to 48K 2 ch 1 ch 1 ch 68 2.7 V

PD78044F 16K to 40K 2 ch

PD780308 48K to 60K 2 ch 1 ch 1 ch 1 ch 8 ch — —

PD78064B 32K

PD78064 16K to 32K

PD78098 32K to 60K 2 ch 1 ch 1 ch 1 ch 8 ch — 2 ch

PD78P0914

32K 6 ch — — 1 ch 8 ch — — 2 ch 54 4.5 V Available

Note 10 bits timer: 1 channel

1 ch (UART: 1 ch) 2 ch (UART: 2 ch) 47 2.7 V

3 ch (Time division UART: 1 ch)

2 ch (UART: 1 ch)

3 ch (UART: 1 ch)

33 1.8 V —

57 2.0 V —

69 2.7 V Available

Available

1.7 Block Diagram

P100/TI5/TO5

P101/TI6/TO6

SI2/R

XD/P70

SO2/T

XD/P71

SCK2/ASCK/P72

ANI0/P10-

ANI7/P17

AVSS

AVREF

INTP1/P01-

INTP3/P03

BUZ/P36

PCL/P35

PORT 0

PORT 1

PORT 3

PORT 5

PORT 7

PORT 10

SYSTEM

CONTROL

8-bit TIMER/ EVENT COUNTER 5

BUZZER OUTPUT

INTERRUPT CONTROL

A/D CONVERTER

SERIAL

INTERFACE 2

WATCHDOG TIMER

CLOCK OUTPUT CONTROL

8-bit TIMER/ EVENT COUNTER 6

78K/0

CPU

CORE

ROM

RAM

P00 P01-P03

P10-P17

P30-P37

P50-P57

P70-P72

P100, P101

RESET X1 X2

VDD VSS IC

PP)

CHAPTER 1 OUTLINE

Remarks 1. The internal ROM and high-speed RAM capacities depend on the product.

2. Pin connection in parentheses is intended for the

PD78P083.

1.8 Outline of Function

CHAPTER 1 OUTLINE

Part Number

PD78081

PD78082

PD78083

Item

Internal memory ROM Mask ROM PROM

8 Kbytes 16 Kbytes 24 Kbytes

High-speed RAM 256 bytes 384 bytes 512 bytes

Note

Memory space 64 Kbytes General register 8 bits × 32 registers (8 bits × 8 registers × 4 banks) Instruction cycle Instruction execution time variable function is integrated.

0.4 µs/0.8 µs/1.6 µs/3.2 µ s/6.4 µs/12.8 µs (@5.0-MHz operation with main system clock)

Instruction set • 16-bit operation

• Multiply/divide (8 bits × 8 bits, 16 bits ÷ 8 bits)

• Bit manipulation (set, reset, test, Boolean operation)

• BCD adjust, etc.

I/O ports Total : 33

• CMOS input : 1

• CMOS input/output : 32 A/D converter • 8-bit resolution × 8 channels Serial interface • 3-wire serial I/O/UART mode selectable: 1 channel Timer • 8-bit timer/event counter: 2 channels

• Watchdog timer: 1 channel Timer output 2 pins (8-bit PWM output enable) Clock output 19.5 kHz, 39.1 kHz, 78.1 kHz, 156 kHz, 313 kHz, 625 kHz, 1.25 MHz, 2.5 MHz,

and 5.0 MHz (@ 5.0-MHz operation with main system clock)

Buzzer output 1.2 kHz, 2.4 kHz, 4.9 kHz, and 9.8 kHz

(@ 5.0-MHz operation with main system clock) Vectored Maskable Internal : 8 external : 3 interrupt Non-maskable Internal : 1 source Software 1 Supply voltage V Operating ambient temperature T

DD = 1.8 to 5.5 V

A = –40 to +85°C

Package • 42-pin plastic shrink DIP (600 mil)

• 44-pin plastic QFP (10 × 10 mm)

• 42-pin ceramic shrink DIP (with window) (600 mil) (

PD78P083 only)

Note Internal PROM and high-speed RAM capacities can be changed by setting the internal memory size

switching register (IMS).

CHAPTER 1 OUTLINE

1.9 Differences between the µPD78081, 78082 and 78P083, the µPD78081(A), 78082(A) and 78P083(A), and the µPD78081(A2)

Table 1-1 Differences between the µPD78081, 78082 and 78P083, the µPD78081(A), 78082(A) and

78P083(A), and the

PD78081(A2)

Part Number

Item Quality grade Standard Special Supply voltage VDD = 1.8 to 5.5 V VDD = 4.5 to 5.5 V Operating ambient temperature TA = –40 to +85°CTA = –40 to +125°C Electrical specifications Please refer to the individual data sheets.

PD78081

PD78082

PD78P083

PD78081(A)

PD78082(A)

PD78P083(A)

PD78081(A2)

[MEMO]

CHAPTER 1 OUTLINE

2.1 Pin Function List

2.1.1 Normal operating mode pins

(1) Port pins

CHAPTER 2 PIN FUNCTION

Pin Name Input/Output Function After Reset P00 Input Port 0 Input only Input — P01 Input/output 4-bit input/output port Input/output is specifiable Input INTP1 P02 bit-wise. When used as the INTP2 P03 input port, it is possible to INTP3

connect a pull-up resistor by software.

P10-P17 Input/output Port 1 Input ANI0-ANI7

8-bit input/output port Input/output is specifiable bit-wise. When used as the input port, it is possible to connect

a pull-up resistor by software. P30-P34 Input/output Port 3 Input — P35 8-bit input/output port PCL P36 Input/output is specifiable bit-wise. BUZ P37 When used as the input port, it is possible to connect —

a pull-up resistor by software. P50-P57 Input/output Port 5 Input —

8-bit input/output port

A maximum of 7 out of 8 ports can drive LEDs directly.

Input/output is specifiable bit-wise.

When used as the input port, it is possible to connect

a pull-up resistor by software. P70 Input/output Port 7 Input SI2/RxD P71 3-bit input/output port SO2/TxD P72 Input/output is specifiable bit-wise. SCK2/ASCK

When used as the input port, it is possible to connect

a pull-up resistor by software. P100 Input/output Port 10 Input TI5/TO5 P101 2-bit input/output port TI6/TO6

Input/output is specifiable bit-wise.

When used as the input port, it is possible to connect

a pull-up resistor by software.

Note

Alternate Function

Note When P10/ANI0-P17/ANI7 pins are used as the analog inputs for the A/D converter, set the port 1 to

the input mode. The on-chip pull-up resistor is automatically disabled.

CHAPTER 2 PIN FUNCTION

(2) Pins other than port pins

Pin Name Input/Output Function After Reset Alternate Function INTP1 Input External interrupt request input by which the active edge Input P01 INTP2 (rising edge, falling edge, or both rising and falling edges) P02 INTP3 can be specified. P03 SI2 Input Serial interface serial data input. Input P70/RxD SO2 Output Serial interface serial data output. Input P71/TxD SCK2 Input/output Serial interface serial clock input/output. Input P72/ASCK RxD Input Asynchronous serial interface serial data input. Input P70/SI2 TxD Output Asynchronous serial interface serial data output. Input P71/SO2 ASCK Input Asynchronous serial interface serial clock input. Input P72/SCK2 TI5 Input External count clock input to 8-bit timer (TM5). Input P100/TO5 TI6 External count clock input to 8-bit timer (TM6). P101/TO6 TO5 Output 8-bit timer output. (also used for 8-bit PWM output) Input P100/TI5 TO6 P101/TI6 PCL Output Clock output. (for main system clock trimming) Input P35 BUZ Output Buzzer output. Input P36 ANI0-ANI7 Input A/D converter analog input. Input P10-P17 AV

REF Input A/D converter reference voltage input. – –

DD – A/D converter analog power supply. Connected to VDD.– –

SS – A/D converter ground potential. Connected to VSS.– –

RESET Input System reset input. – – X1 Input Main system clock oscillation crystal connection. – – X2 – –– V

DD – Positive power supply. – –

PP – High-voltage applied during program write/verification. – –

Connected directly to V

SS – Ground potential. – –

IC – Internal connection. Connect directly to V NC – Does not internally connected. Connect to V

(It can be left open)

SS in normal operating mode.

SS.––

2.1.2 PROM programming mode pins (µPD78P083 only)

Pin Name Input/Output Function

RESET Input PROM programming mode setting.

When +5 V or +12.5 V is applied to the VPP pin or a low level voltage is applied to the

RESET pin, the PROM programming mode is set. VPP Input High-voltage application for PROM programming mode setting and program write/verify. A0 to A14 Input Address bus D0 to D7 Input/output Data bus CE Input PROM enable input/program pulse input OE Input Read strobe input to PROM PGM Input Program/program inhibit input in PROM programming mode VDD — Positive power supply VSS — Ground potential

CHAPTER 2 PIN FUNCTION

2.2 Description of Pin Functions

2.2.1 P00 to P03 (Port 0)

These are 4-bit input/output ports. Besides serving as input/output ports, they function as an external interrupt

request input.

The following operating modes can be specified bit-wise.

(1) Port mode

P00 functions as input-only port and P01 to P03 function as input/output ports. P01 to P03 can be specified for input or output ports bit-wise with a port mode register 0 (PM0). When they are used as input ports, on-chip pull-up resistors can be used to them by defining the pull-up resistor option register L (PUOL).

(2) Control mode

INTP1 to INTP3 function as external interrupt request input pins which are capable of specifying the valid edges (rising edge, falling edge, and both rising and falling edges).

2.2.2 P10 to P17 (Port 1)

These are 8-bit input/output ports. Besides serving as input/output ports, they function as an A/D converter analog

input.

The following operating modes can be specified bit-wise.

(1) Port mode

These ports function as 8-bit input/output ports. They can be specified bit-wise as input or output ports with a port mode register 1 (PM1). If used as input ports, on-chip pull-up resistors can be used to these ports by defining the pull-up resistor option register L (PUOL).

(2) Control mode

These ports function as A/D converter analog input pins (ANI0-ANI7). The on-chip pull-up resistor is automatically disabled when the pins specified for analog input.

CHAPTER 2 PIN FUNCTION

2.2.3 P30 to P37 (Port 3)

These are 8-bit input/output ports. Beside serving as input/output ports, they function as clock output and buzzer

output.

The following operating modes can be specified bit-wise.

(1) Port mode

These ports function as 8-bit input/output ports. They can be specified bit-wise as input or output ports with port mode register 3 (PM3). When they are used as input ports, on-chip pull-up resistors can be used by defining the pull-up resistor option register L (PUOL).

(2) Control mode

These ports function as clock output, and buzzer output.

(a) PCL

Clock output pin.

(b) BUZ

Buzzer output pin.

2.2.4 P50 to P57 (Port 5)

These are 8-bit input/output ports. They can be specified bit-wise as input/output ports with port mode register 5 (PM5). When they are used as input ports, on-chip pull-up resistors can be used by defining the pull-up resistor option register L (PUOL). A maximum of 7 out of 8 ports can drive LEDs directly.

CHAPTER 2 PIN FUNCTION

2.2.5 P70 to P72 (Port 7)

This is a 3-bit input/output port. In addition to its use as an input/output port, it also has serial interface data input/

output and clock input/output functions.

The following operating modes can be specified bit-wise.

(1) Port mode

Port 7 functions as a 3-bit input/output port. Bit-wise specification as an input port or output port is possible by means of port mode register 7 (PM7). When used as input ports, on-chip pull-up resistors can be used by defining the pull-up resistor option register L (PUOL).

(2) Control mode

Port 7 functions as serial interface data input/output and clock input/output.

(a) SI2, SO2

Serial interface serial data input/output pins

(b) SCK2

Serial interface serial clock input/output pin.

Asynchronous serial interface serial data input/output pins.

(d) ASCK

Asynchronous serial interface serial clock input pin.

Caution When this port is used as a serial interface, the I/O and output latches must be set according

to the function the user requires. For the setting, see the operation mode setting list in Table 11-2 “Serial Interface Channel 2 Operating Mode Settings”

2.2.6 P100 to P101 (Port 10)

These are 2-bit input/output ports. Besides serving as input/output ports, they function as timer input/output. The following operating modes can be specified bit-wise.

(1) Port mode

These ports function as 2-bit input/output ports. They can be specified bit-wise as input or output ports with port mode register 10 (PM10). When they are used as input ports, on-chip pull-up resistors can be used by defining the pull-up resistor option register H (PUOH).

(2) Control mode

These ports function as timer input/output.

(a) TI5, TI6

Pin for external clock input to the 8-bit timer/event counter 5 and 6.

(b) TO5, TO6

Timer output pins.

CHAPTER 2 PIN FUNCTION

2.2.7 AVREF

A/D converter reference voltage input pin.

When A/D converter is not used, connect this pin to V

SS.

2.2.8 AV

Analog power supply pin of A/D converter. Always use the same voltage as that of the VDD pin even when A/D converter is not used.

2.2.9 AVSS

This is a ground voltage pin of A/D converter. Always use the same voltage as that of the VSS pin even when A/ D converter is not used.

2.2.10 RESET

This is a low-level active system reset input pin.

2.2.11 X1 and X2

Crystal resonator connect pins for main system clock oscillation. For external clock supply, input it to X1 and its inverted signal to X2.

2.2.12 V

Positive power supply pin

2.2.13 V

Ground potential pin

2.2.14 V

PP (

PD78P083 only)

High-voltage apply pin for PROM programming mode setting and program write/verify. Connect directly to V in normal operating mode.

CHAPTER 2 PIN FUNCTION

2.2.15 IC (Mask ROM version only)

The IC (Internally Connected) pin is provided to set the test mode to check the

Connect it directly to the V

When a voltage difference is produced between the IC pin and V

SS with the shortest possible wire in the normal operating mode.

SS pin because the wiring between those two pins

PD78083 Subseries at delivery.

is too long or an external noise is input to the IC pin, the user's program may not run normally.

Connect IC pins to VSS pins directly.

VSS IC

As short as possible

2.2.16 NC (44-pin plastic QFP versions only)

Not internally connected. Please connect to Vss (open is also possible)

CHAPTER 2 PIN FUNCTION

2.3 Pin Input/Output Circuits and Recommended Connection of Unused Pins

Types of input/output circuits of the pins and recommeded connection of unused pins are shown in Table 2-1.

For the configuration of each type of input/output circuit, see Figure 2-1.

Table 2-1. Type of Input/Output Circuit of Each Pin

Pin Name Input/Output Input/Output Recommended Connection for Unused Pins

Circuit Type P00 2 Input Connect to V P01/INTP1 8-A Input/Output Independently connect to VSS via a resistor. P02/INTP2 P03/INTP3 P10/ANI0-P17/ANI7 11 Input/Output Independently connect to V P30-P32 5-A a resistor. P33, P34 8-A P35/PCL 5-A P36/BUZ P37 P50-P57 5-A P70/SI2/RxD 8-A P71/SO2/TxD 5-A P72/SCK2/ASCK 8-A P100/TI5/TO5 8-A P101/TI6/TO6 RESET 2 Input – AV

REF – – Connect to VSS.

AVDD Connect to VDD. AV

SS Connect to V SS.

VPP (µPD78P083) Connect directly to VSS. NC (44-pin plastic QFP Connect to V version) IC (Mask ROM version) Connect directly to V

SS.

DD or VSS via

SS (can also leave open)

SS.

CHAPTER 2 PIN FUNCTION

Figure 2-1. Pin Input/Output Circuit of List

Type 2

Type 5-A

pull-up enable

data

output disable

input enable

Schmitt-Triggered Input with Hysteresis Characteristics

VDD

P-ch

N-ch

P-ch

IN/OUT

Type 8-A

pull-up enable

data

output disable

Type 11

pull-up enable

output

disable

comparator

input enable

data

VDD

N-ch

P-ch

+ –

N-ch

REF (Threshold voltage)

P-ch

N-ch

VDD

P-ch

IN/OUT

[MEMO]

CHAPTER 2 PIN FUNCTION

3.1 Memory Spaces

Figures 3-1 to 3-3 shows memory maps.

CHAPTER 3 CPU ARCHITECTURE

Data memory space

Program memory space

FFFFH

FF00H FEFFH

FEE0H FEDFH

FE00H FDFFH

2000H 1FFFH

Figure 3-1. Memory Map (

Special Function Registers (SFRs)

256 × 8 bits

General Registers

32 × 8 bits

Internal High-speed RAM

256 × 8 bits

Unusable

Internal ROM

8192 × 8 bits

PD78081)

1FFFH

Program Area

1000H 0FFFH

CALLF Entry Area

0800H 07FFH

Program Area

0080H 007FH

CALLT Table Area

0040H 003FH

Vector Table Area

0000H

CHAPTER 3 CPU ARCHITECTURE

Figure 3-2. Memory Map (µPD78082)

Data memory space

Program memory space

FFFFH

FF00H FEFFH

FEE0H FEDFH

FD80H FD7FH

4000H 3FFFH

Special Function Registers (SFRs)

256 × 8 bits

General Registers

32 × 8 bits

Internal High-speed RAM

384 × 8 bits

Unusable

Internal ROM

16384 × 8 bits

3FFFH

Program Area

1000H 0FFFH

CALLF Entry Area

0800H 07FFH

Program Area

0080H 007FH

CALLT Table Area

0040H 003FH

Vector Table Area

0000H

CHAPTER 3 CPU ARCHITECTURE

Figure 3-3. Memory Map (µPD78P083)

Data memory space

Program memory space

FFFFH

FF00H FEFFH

FEE0H FEDFH

FD00H FCFFH

6000H 5FFFH

Special Function

Registers (SFRs)

256 × 8 bits

General Registers

32 × 8 bits

Internal High-speed RAM

512 × 8 bits

Unusable

Internal PROM

24576 × 8 bits

5FFFH

Program Area

1000H 0FFFH

CALLF Entry Area

0800H 07FFH

Program Area

0080H 007FH

CALLT Table Area

0040H 003FH

Vector Table Area

0000H

CHAPTER 3 CPU ARCHITECTURE

3.1.1 Internal program memory space

The internal program memory is mask ROM with a 8192 × 8-bit configuration in the

8-bit configuration in the

The internal program memory space

PD78082, and PROM with a 24576 × 8-bit configuration in the µPD78P083.

stores programs and table data. Normally, they are addressed with a program

counter (PC).

The internal program memory is divided into the following three areas.

(1) Vector table area

The 64-byte area 0000H to 003FH is reserved as a vector table area. The RESET input and program start addresses for branch upon generation of each interrupt request are stored in the vector table area. Of the 16-bit address, low-order 8 bits are stored at even addresses and high-order 8 bits are stored at odd addresses.

Table 3-1. Vector Table

Vector Table Address Interrupt Request

0000H RESET input 0004H INTWDT 0008H INTP1 000AH INTP2 000CH INTP3 0018H INTSER 001AH INTSR/INTCSI2 001CH INTST 0028H INTAD 002AH INTTM5 002CH INTTM6 003EH BRK

PD78081, and a 16384 ×

(2) CALLT instruction table area

The 64-byte area 0040H to 007FH can store the subroutine entry address of a 1-byte call instruction (CALLT).

(3) CALLF instruction entry area

The area 0800H to 0FFFH can perform a direct subroutine call with a 2-byte call instruction (CALLF).

CHAPTER 3 CPU ARCHITECTURE

3.1.2 Internal data memory space

The internal high speed RAM configuration is 256 × 8-bit in the

× 8-bit in the

are allocated in the 32-byte area FEE0H to FEFFH.

The internal high-speed RAM can also be used as a stack memory area.

3.1.3 Special Function Register (SFR) area

An on-chip peripheral hardware special-function register (SFR) is allocated in the area FF00H to FFFFH. (Refer

to Table 3-2. Special-Function Register List in 3.2.3 Special Function Register (SFR) ).

Caution Do not access addresses where the SFR is not assigned.

3.1.4 Data memory addressing

The method to specify the address of the instruction to be executed next, or the address of a register or memory

to be manipulated when an instruction is executed is called addressing.

The address of the instruction to be executed next is addressed by the program counter PC (for details, refer to

3.3 Instruction Address Addressing).

To address the memory that is manipulated when an instruction is executed, the with many addressing modes with a high operability. Especially at addresses corresponding to data memory area, particular addressing modes are possible to meet the functions of the special function registers (SFRs) and general registers. This area is between FE00H and FFFFH for the between FD00H and FFFFH for the FFFFH). Figure 3-4 to 3-6 show the data memory addressing modes. For details of each addressing, refer to 3.4

Operand Address Addressing.

PD8P083. In this area, four banks of general registers, each bank consisting of eight 8-bit registers,

PD78P083. The data memory space is the entire 64K-byte space (0000H to

PD78081, 384 × 8-bit in the µPD78082 and 512

PD78083 Subseries is provided

PD78081, FD80H and FFFFH for the µPD78082, and

CHAPTER 3 CPU ARCHITECTURE

Figure 3-4. Data Memory Addressing (µPD78081)

FFFFH

FF20H FF1FH

FF00H FEFFH

FEE0H FEDFH

FE20H FE1FH

FE00H FDFFH

2000H 1FFFH

0000H

Special Function Registers (SFRs)

256 × 8 bits

General Registers

32 × 8 bits

Internal High-speed RAM

256 × 8 bits

Unusable

Internal ROM

8192 × 8 bits

SFR Addressing

Short Direct Addressing

Direct Addressing Register Indirect

Addressing Based Addressing

Based Indexed Addressing

CHAPTER 3 CPU ARCHITECTURE

Figure 3-5. Data Memory Addressing (µPD78082)

FFFFH

FF20H FF1FH

FF00H FEFFH

FEE0H FEDFH

FE20H FE1FH

FD80H FD7FH

4000H 3FFFH

0000H

Special Function Registers (SFRs)

256 × 8 bits

General Registers

32 × 8 bits

Internal High-speed RAM

384 × 8 bits

Unusable

Internal ROM

16384 × 8 bits

SFR Addressing

Short Direct Addressing

Direct Addressing Register Indirect

Addressing Based Addressing

Based Indexed Addressing

CHAPTER 3 CPU ARCHITECTURE

Figure 3-6. Data Memory Addressing (µPD78P083)

FFFFH

FF20H FF1FH

FF00H FEFFH

FEE0H FEDFH

FE20H FE1FH

FD00H FCFFH

6000H 5FFFH

0000H

Special Function

Registers (SFRs)

256 × 8 bits

General Registers

32 × 8 bits

Internal High-speed RAM

512 × 8 bits

Unusable

Internal PROM

24576 × 8 bits

SFR Addressing

Short Direct Addressing

Direct Addressing Register Indirect

Addressing Based Addressing

Based Indexed Addressing

CHAPTER 3 CPU ARCHITECTURE

3.2 Processor Registers

The µPD78083 subseries units incorporate the following processor registers.

3.2.1 Control registers

The control registers control the program sequence, statuses and stack memory. The control registers consist of a program counter, a program status word and a stack pointer.

(1) Program counter (PC)

The program counter is a 16-bit register which holds the address information of the next program to be executed. In normal operation, the PC is automatically incremented according to the number of bytes of the instruction to be fetched. When a branch instruction is executed, immediate data and register contents are set. RESET input sets the reset vector table values at addresses 0000H and 0001H to the program counter.

Figure 3-7. Program Counter Configuration

15 0

(2) Program status word (PSW)

The program status word is an 8-bit register consisting of various flags to be set/reset by instruction execution. Program status word contents are automatically stacked upon interrupt request generation or PUSH PSW instruction execution and are automatically reset upon execution of the RETB, RETI and POP PSW

instructions.

RESET input sets the PSW to 02H.

Figure 3-8. Program Status Word Configuration

IE Z RBS1 AC RBS0 0 ISP CY

CHAPTER 3 CPU ARCHITECTURE

(a) Interrupt enable flag (IE)

This flag controls the interrupt request acknowledge operations of the CPU. When IE = 0, all interrupts except the non-maskable interrupt are disabled (DI status). When IE = 1, interrupts are enabled (EI status). At this time, acknowledgment of interrupts is controlled with an inservice priority flag (ISP), an interrupt mask flag for various interrupt sources, and a priority specify flag. The interrupt enable flag is reset to 0 when the DI instruction is executed or when an interrupt request is acknowledged, and set to 1 when the EI instruction is executed.

(b) Zero flag (Z)

When the operation result is zero, this flag is set (1). It is reset (0) in all other cases.

These are 2-bit flags to select one of the four register banks. In these flags, the 2-bit information which indicates the register bank selected by SEL RBn instruction execution is stored.

(d) Auxiliary carry flag (AC)

If the operation result has a carry from bit 3 or a borrow at bit 3, this flag is set (1). It is reset (0) in all other cases.

(e) In-service priority flag (ISP)

This flag manages the priority of acknowledgeable maskable vectored interrupts. When ISP = 0, the vectored interrupt request whose priority is specified by the priority specify flag registers (PR0L, PR0H, and PR1L) (Refer to 12.3 (3) Priority specify flag registers (PR0L, PR0H, and PR1L)) to be low is disabled. Whether the interrupt request is actually acknowledged is controlled by the status of the interrupt enable flag (IE).

(f) Carry flag (CY)

This flag stores overflow and underflow upon add/subtract instruction execution. It stores the shift-out value upon rotate instruction execution and functions as a bit accumulator during bit manipulation instruction execution.

CHAPTER 3 CPU ARCHITECTURE

(3) Stack pointer (SP)

This is a 16-bit register to hold the start address of the memory stack area. Only the internal high-speed RAM

area (FE00H-FEFFH for the

PD78P083) can be set as the stack area.

PD78081, FD80H-FEFFH for the µPD78082, and FD00H-FEFFH for the

Figure 3-9. Stack Pointer Configuration

015

The SP is decremented ahead of write (save) to the stack memory and is incremented after read (reset) from the stack memory. Each stack operation saves/resets data as shown in Figures 3-10 and 3-11.

Caution Since RESET input makes SP contents indeterminate, be sure to initialize the SP before

instruction execution.

Figure 3-10. Data to be Saved to Stack Memory

SP SP _ 2

SP _ 2

SP _ 1

PUSH rp Instruction

Figure 3-11. Data to be Reset from Stack Memory

SP SP _ 2

SP _ 2

SP _ 1

CALL, CALLF, and CALLT Instruction

PC7-PC0

PC15-PC8

RET InstructionPOP rp Instruction

PC7-PC0

SP SP _ 3

SP _ 3

SP _ 2

SP _ 1

Interrupt and BRK Instruction

PC7-PC0

PC15-PC8

PSW

RETI and RETB Instruction

PC7-PC0

SP + 1

SP SP + 2

SP + 1

SP SP + 2

PC15-PC8

SP + 1

SP + 2

SP SP + 3

PC15-PC8

PSW

CHAPTER 3 CPU ARCHITECTURE

3.2.2 General registers

A general register is mapped at particular addresses (FEE0H to FEFFH) of the data memory. It consists of 4 banks,

each bank consisting of eight 8-bit registers (X, A, C, B, E, D, L and H).

Each register can also be used as an 8-bit register. Two 8-bit registers can be used in pairs as a 16-bit register

(AX, BC, DE and HL).

They can be described in terms of function names (X, A, C, B, E, D, L, H, AX, BC, DE and HL) and absolute names

(R0 to R7 and RP0 to RP3).

Register banks to be used for instruction execution are set with the CPU control instruction (SEL RBn). Because of the 4-register bank configuration, an efficient program can be created by switching between a register for normal processing and a register for interruption request for each bank.

Figure 3-12. General Register Configuration

(a) Absolute Name

16-Bit Processing 8-Bit Processing

FEFFH

FEF8H

FEF0H

FEE8H

FEE0H

BANK0

BANK1

BANK2

BANK3

RP3

RP2

RP1

RP0

15 0 7 0

FEFFH

FEF8H

FEF0H

FEE8H

FEE0H

BANK0

BANK1

BANK2

BANK3

(b) Function Name

16-Bit Processing 8-Bit Processing

15 0 7 0

CHAPTER 3 CPU ARCHITECTURE

3.2.3 Special Function Register (SFR)

Unlike a general register, each special-function register has special functions. It is allocated in the FF00H to FFFFH area. The special-function register can be manipulated like the general register, with the operation, transfer and bit

manipulation instructions. Manipulatable bit units, 1, 8 and 16, depend on the special-function register type.

Each manipulation bit unit can be specified as follows.

• 1-bit manipulation Describe the symbol reserved with assembler for the 1-bit manipulation instruction operand (sfr.bit). This manipulation can also be specified with an address.

• 8-bit manipulation Describe the symbol reserved with assembler for the 8-bit manipulation instruction operand (sfr). This manipulation can also be specified with an address.

• 16-bit manipulation Describe the symbol reserved with assembler for the 16-bit manipulation instruction operand (sfrp). When addressing an address, describe an even address.

Table 3-2 gives a list of special-function registers. The meaning of items in the table is as follows.

• Symbol Symbols indicating the addresses of special function register. These symbols are reserved words for the RA78K/ 0 and defined by header file sfrbit.h for the CC78K/0, and can be used as the operands of instructions when the RA78K/0, ID78K0, and SD78K/0 are used.

• R/W Indicates whether the corresponding special-function register can be read or written. R/W : Read/write enable R : Read only W : Write only

• Manipulatable bit units √ indicates bit units (1, 8 or 16 bits) in which the register can be manipulated. — indicates that the register cannot be manipulated in the indicated bit units.

• After reset Indicates each register status upon RESET input.

CHAPTER 3 CPU ARCHITECTURE

Table 3-2. Special-Function Register List (1/2)

Address Special-Function Register (SFR) Name Symbol R/W After Reset

FF00H Port0 P0 R/W √√— 00H FF01H Port1 P1 √√— FF03H Port3 P3 √√— FF05H Port5 P5 √√— FF07H Port7 P7 √√— FF0AH Port10 P10 √√— FF1FH A/D conversion result register ADCR R √√— Undefined FF20H Port mode register 0 PM0 R/W √√— FFH FF21H Port mode register 1 PM1 √√— FF23H Port mode register 3 PM3 √√— FF25H Port mode register 5 PM5 √√— FF27H Port mode register 7 PM7 √√— FF2AH Port mode register 10 PM10 √√— FF40H Timer clock select register 0 TCL0 √√— 00H FF42H Timer clock select register 2 TCL2 — √ — FF50H Compare Register 50 CR50 — √ — FF51H 8-bit timer register 5 TM5 R — √ — FF52H Timer clock select register 5 TCL5 R/W — √ — FF53H 8-bit timer mode control register 5 TMC5 √√— FF54H Compare Register 60 CR60 — √ — FF55H 8-bit timer register 6 TM6 R — √ — FF56H Timer clock select register 6 TCL6 R/W — √ — FF57H 8-bit timer mode control register 6 TMC6 √√— FF70H

FF71H FF72H Serial operating mode register 2 CSIM2 R/W √√— FF73H Baud rate generator control register BRGC — √ —

FF74H Transmit shift register TXS SIO2 W — √ — FFH

FF80H A/D converter mode register ADM R/W √√— 01H FF84H A/D converter input select register ADIS — √ — 00H FFE0H Interrupt request flag register 0L IF0 IF0L √√ √ FFE1H Interrupt request flag register 0H IF0H √√ FFE2H Interrupt request flag register 1L IF1L √√— FFE4H Interrupt mask flag register 0L MK0 MK0L √√ √FFH

FFE5H Interrupt mask flag register 0H MK0H √√ FFE6H Interrupt mask flag register 1L MK1L √√— FFE8H Priority order specify flag register 0L PR0 PR0L √√ √ FFE9H Priority order specify flag register 0H PR0H √√

Asynchronous serial interface mode register Asynchronous serial interface status register

Receive buffer register RXB R

ASIM √√—

ASIS R √√—

Manipulatable Bit Unit

8 bits1 bit 16 bits

CHAPTER 3 CPU ARCHITECTURE

Table 3-2. Special-Function Register List (2/2)

Address Special-Function Register (SFR) Name Symbol R/W After Reset

FFEAH Priority order specify flag register 1L PR1L R/W √√— FFH FFECH External interrupt mode register 0 INTM0 — √ — 00H FFEDH External interrupt mode register 1 INTM1 — √ — FFF0H Memory size switching register IMS — √ — FFF2H Oscillation mode selection register OSMS W — √ — 00H FFF3H Pull-up resistor option register H PUOH R/W √√— FFF7H Pull-up resistor option register L PUOL √√— FFF9H Watchdog timer mode register WDTM √√— FFFAH FFFBH Processor clock control register PCC √√—

Oscillation stabilization time select register

OSTS — √ — 04H

Manipulatable Bit Unit

8 bits1 bit 16 bits

(Note)

Note The value after reset depends on products.

PD78081 : 82H, µPD78082 : 64H, µPD78P083 : 46H.

CHAPTER 3 CPU ARCHITECTURE

3.3 Instruction Address Addressing

An instruction address is determined by program counter (PC) contents. The contents of PC are normally incremented (+1 for each byte) automatically according to the number of bytes of an instruction to be fetched each time another instruction is executed. When a branch instruction is executed, the branch destination information is set to the PC and branched by the following addressing. (For details of instructions, refer to 78K/0 USER'S MANUAL:

Instruction (IEU-1372).

3.3.1 Relative addressing

[Function]

The value obtained by adding 8-bit immediate data (displacement value: jdisp8) of an instruction code to the start address of the following instruction is transferred to the program counter (PC) and branched. The displacement value is treated as signed two's complement data (–128 to +127) and bit 7 becomes a sign bit. In the relative addressing modes, execution branches in a relative range of –128 to +127 from the first address of the next instruction. This function is carried out when the BR $addr16 instruction or a conditional branch instruction is executed.

[Illustration]

15 0

When S = 0, all bits of α are 0. When S = 1, all bits of α are 1.

876

jdisp8

PC indicates the start address

...

of the instruction after the BR instruction.

CHAPTER 3 CPU ARCHITECTURE

3.3.2 Immediate addressing

[Function]

Immediate data in the instruction word is transferred to the program counter (PC) and branched. This function is carried out when the CALL !addr16 or BR !addr16 or CALLF !addr11 instruction is executed. The CALL !addr16 and BR !addr16 instruction can branch in the entire memory space. The CALLF !addr11 instruction branches to an area of addresses 0800H through 0FFFH.

[Illustration]

In the case of CALL !addr16 and BR !addr16 instructions

CALL or BR

Low Addr.

High Addr.

15 0

In the case of CALLF !addr11 instruction

643

10–8

7–0

15 0

00001

CALLF

11 10

CHAPTER 3 CPU ARCHITECTURE

3.3.3 Table indirect addressing

[Function]

Table contents (branch destination address) of the particular location to be addressed by bits 1 to 5 of the immediate data of an operation code are transferred to the program counter (PC) and branched. Before the CALLT [addr5] instruction is executed, table indirect addressing is performed. This instruction references an address stored in the memory table at addresses 40H through 7FH, and can branch in the entire memory space.

[Illustration]

765 10

Operation Code

ta4–0

111

Effective Address

Effective Address+1

15 1

00000000

Memory (Table)

Low Addr.

High Addr.

15 0

65 0

CHAPTER 3 CPU ARCHITECTURE

3.3.4 Register addressing

[Function]

Register pair (AX) contents to be specified with an instruction word are transferred to the program counter (PC) and branched. This function is carried out when the BR AX instruction is executed.

[Illustration]

15 0

CHAPTER 3 CPU ARCHITECTURE

3.4 Operand Address Addressing

The following various methods are available to specify the register and memory (addressing) which undergo manipulation during instruction execution.

3.4.1 Implied addressing

[Function]

The register which functions as an accumulator (A and AX) in the general register is automatically (illicitly) addressed.

Of the

PD78083 Subseries instruction words, the following instructions employ implied addressing.

Instruction Register to be Specified by Implied Addressing MULU A register for multiplicand and AX register for product storage DIVUW AX register for dividend and quotient storage ADJBA/ADJBS A register for storage of numeric values which become decimal correction targets ROR4/ROL4 A register for storage of digit data which undergoes digit rotation

[Operand format]

Because implied addressing can be automatically employed with an instruction, no particular operand format is necessary.

[Description example]

In the case of MULU X With an 8-bit × 8-bit multiply instruction, the product of A register and X register is stored in AX. In this example, the A and AX registers are specified by implied addressing.

CHAPTER 3 CPU ARCHITECTURE

3.4.2 Register addressing

[Function]

This addressing accesses a general register as an operand. The general register accessed is specified by the register bank select flags (RBS0 and RBS1) and register specify code (Rn or RPn) in an instruction code. Register addressing is carried out when an instruction with the following operand format is executed. When an 8-bit register is specified, one of the eight registers is specified with 3 bits in the operation code.

[Operand format]

Identifier Description

r X, A, C, B, E, D, L, H rp AX, BC, DE, HL

'r' and 'rp' can be described with function names (X, A, C, B, E, D, L, H, AX, BC, DE and HL) as well as absolute names (R0 to R7 and RP0 to RP3).

[Description example]

MOV A, C; when selecting C register as r

Operation code 0 1 1 0 0 0 1 0

INCW DE; when selecting DE register pair as rp

Operation code 1 0 0 0 0 1 0 0

CHAPTER 3 CPU ARCHITECTURE

3.4.3 Direct addressing

[Function]

This addressing directly addresses the memory indicated by the immediate data in an instruction word.

[Operand format]

Identifier Description

addr16 Label or 16-bit immediate data

[Description example]

MOV A, !0FE00H; when setting !addr16 to FE00H

Operation code 1 0 0 0 1 1 1 0 OP code

00000000 00H

11111110 FEH

[Illustration]

OP code

saddr16 (low)

saddr16 (high)

Memory

CHAPTER 3 CPU ARCHITECTURE

3.4.4 Short direct addressing

[Function]

The memory to be manipulated in the fixed space is directly addressed with 8-bit data in an instruction word. The fixed space to which this address is applied is a 256-byte space of addresses FE20H through FF1FH. An internal high-speed RAM and a special-function register (SFR) are mapped at FE20H to FEFFH and FF00H to FF1FH, respectively. The SFR area (FF00H through FF1FH) to which short direct addressing is applied is a part of the entire SFR area. To this area, ports frequently accessed by the program, and the compare registers and capture registers of timer/event counters are mapped. These SFRs can be manipulated with a short byte length and a few clocks. When 8-bit immediate data is at 20H to FFH, bit 8 of an effective address is set to 0. When it is at 00H to 1FH, bit 8 is set to 1. Refer to [Illustration] on next page.

[Operand format]

Identifier Description

saddr Label of FE20H to FF1FH immediate data saddrp Label of FE20H to FF1FH immediate data (even address only)

CHAPTER 3 CPU ARCHITECTURE

[Description example]

MOV 0FE30H, #50H; when setting saddr to FE30H and immediate data to 50H

Operation code 0 0 0 1 0 0 0 1 OP code

0 0 1 1 0 0 0 0 30H (saddr-offset)

0 1 0 1 0 0 0 0 50H (immediate data)

[Illustration]

OP code

saddr-offset

Effective Address

111111

When 8-bit immediate data is 20H to FFH, α = 0 When 8-bit immediate data is 00H to 1FH, α = 1

Short Direct Memory

CHAPTER 3 CPU ARCHITECTURE

SFR

Effective Address

111111

07 OP code sfr-offset

3.4.5 Special-Function Register (SFR) addressing

[Function]

The memory-mapped special-function register (SFR) is addressed with 8-bit immediate data in an instruction word. This addressing is applied to the 240-byte spaces FF00H to FFCFH and FFE0H to FFFFH. However, the SFR mapped at FF00H to FF1FH can be accessed with short direct addressing.

[Operand format]

Identifier Description

sfr Special-function register name sfrp 16-bit manipulatable special-function register name (even address only)

[Description example]

MOV PM0, A; when selecting PM0 (FF20H) as sfr

[Illustration]

Operation code 1 1 1 1 0 1 1 0 OP code

0 0 1 0 0 0 0 0 20H (sfr-offset)

CHAPTER 3 CPU ARCHITECTURE

3.4.6 Register indirect addressing

[Function]

This addressing addresses the memory with the contents of a register pair specified as an operand. The register pair to be accessed is specified by the register bank select flags (RBS0 and RBS1) and register pair specify code in an instruction code. This addressing can be carried out for all the memory spaces.

[Operand format]

Identifier Description

— [DE], [HL]

[Description example]

MOV A, [DE]; when selecting [DE] as register pair

Operation code 1 0 0 0 0 1 0 1

[Illustration]

Contents of addressed memory are transferred.

16 08D7

7 0

Memory

Memory address specified

by register pair DE

CHAPTER 3 CPU ARCHITECTURE

3.4.7 Based addressing

[Function]

This addressing addresses the memory by adding 8-bit immediate data to the contents of the HL register pair which is used as a base register and by using the result of the addition. The HL register pair to be accessed is in the register bank specified by the register bank select flags (RBS0 and RBS1). Addition is performed by expanding the offset data as a positive number to 16 bits. A carry from the 16th bit is ignored. This addressing can be carried out for all the memory spaces.

[Operand format]

Identifier Description

— [HL + byte]

[Description example]

MOV A, [HL + 10H]; when setting byte to 10H

Operation code 1 0 1 0 1 1 1 0

00010000

CHAPTER 3 CPU ARCHITECTURE

3.4.8 Based indexed addressing

[Function]

This addressing addresses the memory by adding the contents of the HL register, which is used as a base register, to the contents of the B or C register specified in the instruction word, and by using the result of the addition. The HL, B, and C registers to be accessed are registers in the register bank specified by the register bank select flags (RBS0 and RBS1). The addition is performed by extending the contents of the B or C register to 16 bits as a positive number. A carry from the 16th bit is ignored. This addressing can be carried out for all the memory spaces.

[Operand format]

Identifier Description

— [HL + B], [HL + C]

[Description example]

In the case of MOV A, [HL + B]

Operation code 1 0 1 0 1 0 1 1

3.4.9 Stack addressing

[Function]

The stack area is indirectly addressed with the stack pointer (SP) contents. This addressing method is automatically employed when the PUSH, POP, subroutine call and RETURN instructions are executed or the register is saved/reset upon generation of an interrupt request. Stack addressing enables to address the internal high-speed RAM area only.

[Description example]

In the case of PUSH DE

Operation code 1 0 1 1 0 1 0 1

CHAPTER 4 PORT FUNCTIONS

4.1 Port Functions

The µPD78083 Subseries units incorporate an input port and thirty-two input/output ports. Figure 4-1 shows the port configuration. Every port is capable of 1-bit and 8-bit manipulations and can carry out considerably varied control operations. Besides port functions, the ports can also serve as on-chip hardware input/output pins.

Figure 4-1. Port Types

Port 5

Port 7

Port 10

P50

P57 P70

P72 P100

P101

P00

Port 0

P03 P10

Port 1

P17 P30

Port 3

P37

CHAPTER 4 PORT FUNCTIONS

Table 4-1. Port Functions

Pin Name Input/Output Function Dual-Function Pin P00 Input Port 0 Input only — P01 Input/output 4-bit input/output port Input/output is specifiable bit-wise. When INTP1 P02 used as the input port, it is possible to connect INTP2 P03 a pull-up resistor by software. INTP3 P10-P17 Input/output Port 1 ANI0-ANI7

8-bit input/output port Input/output is specifiable bit-wise. When used as the input port, it is possible to connect a pull-up resistor

by software. P30-P34 Input/output Port 3 — P35 8-bit input/output port PCL P36 Input/output is specifiable bit-wise. BUZ P37 When used as the input port, it is possible to connect a pull-up resistor —

by software. P50-P57 Input/output Port 5 —

8-bit input/output port

A maximum of 7 out of 8 ports can drive LEDs directly.

Input/output is specifiable bit-wise.

When used as the input port, it is possible to connect a pull-up resistor

by software. P70 Input/output Port 7 SI2/RxD P71 3-bit input/output port SO2/TxD P72 Input/output is specifiable bit-wise. SCK2/ASCK

When used as the input port, it is possible to connect a pull-up resistor

by software. P100 Input/output Port 10 TI5/TO5 P101 2-bit input/output port TI6/TO6

Input/output is specifiable bit-wise.

When used as the input port, it is possible to connect a pull-up resistor

by software.

CHAPTER 4 PORT FUNCTIONS

4.2 Port Configuration

A port consists of the following hardware:

Table 4-2. Port Configuration

Item Configuration Control register Port mode register (PMm: m = 0, 1, 3, 5, 7, 10)

Pull-up resistor option register (PUOH, PUOL) Port Total: 33 ports (1 input, 32 inputs/outputs) Pull-up resistor

4.2.1 Port 0

Port 0 is an 4-bit input/output port with output latch. P01 to P03 pins can specify the input mode/output mode in 1-bit units with the port mode register 0 (PM0). P00 pin is input-only port. When P01 to P03 pins are used as input ports, an on-chip pull-up resistor can be used to them in 3-bit units with a pull-up resistor option register L (PUOL).

Dual-functions include external interrupt request input.

RESET input sets port 0 to input mode.

Figures 4-2 and 4-3 show block diagrams of port0.

Total: 32 (software specifiable)

Caution Because port 0 also serves for external interrupt request input, when the port function output

mode is specified and the output level is changed, the interrupt request flag is set. Thus, when the output mode is used, set the interrupt mask flag to 1.

CHAPTER 4 PORT FUNCTIONS

Figure 4-2. P00 Block Diagram

PUO

WRPORT

Internal bus

WRPM

Internal bus

Figure 4-3. P01 to P03 Block Diagram

PUO0

Output Latch (P01 to P03)

P00

VDD

P-ch

Selector

P01/INTP1 P03/INTP3

PM01-PM03

PUO : Pull-up resistor option register PM : Port mode register RD : Port 0 read signal WR : Port 0 write signal

CHAPTER 4 PORT FUNCTIONS

4.2.2 Port 1

Port 1 is an 8-bit input/output port with output latch. It can specify the input mode/output mode in 1-bit units with a port mode register 1 (PM1). When P10 to P17 pins are used as input ports, an on-chip pull-up resistor can be used to them in 8-bit units with a pull-up resistor option register L (PUOL).

Dual-functions include an A/D converter analog input.

RESET input sets port 1 to input mode.

Figure 4-4 shows a block diagram of port 1.

Caution A pull-up resistor cannot be used for pins used as A/D converter analog input.

Figure 4-4. P10 to P17 Block Diagram

PUO

PORT

Internal bus

PUO1

Selector

Output Latch (P10 to P17)

PM10-PM17

PUO : Pull-up resistor option register PM : Port mode register RD : Port 1 read signal WR : Port 1 write signal

P-ch

P10/ANI0 P17/ANI7

CHAPTER 4 PORT FUNCTIONS

4.2.3 Port 3

Port 3 is an 8-bit input/output port with output latch. P30 to P37 pins can specify the input mode/output mode in 1-bit units with the port mode register 3 (PM3). When P30 to P37 pins are used as input ports, an on-chip pull-up resistor can be used to them in 8-bit units with a pull-up resistor option register L (PUOL).

Dual-functions include clock output and buzzer output.

RESET input sets port 3 to input mode.

Figure 4-5 shows a block diagram of port 3.

Figure 4-5. P30 to P37 Block Diagram

VDD

PUO

WRPORT

Internal bus

WRPM

PUO : Pull-up resistor option register PM : Port mode register RD : Port 3 read signal WR : Port 3 write signal

PUO3

Output Latch (P30 to P37)

PM30-PM37

Alternate Function

P-ch

Selector

P30 P34,

P35/PCL, P36/BUZ, P37

CHAPTER 4 PORT FUNCTIONS

4.2.4 Port 5

Port 5 is an 8-bit input/output port with output latch. P50 to P57 pins can specify the input mode/output mode in 1-bit units with the port mode register 5 (PM5). When P50 to P57 pins are used as input ports, an on-chip pull-up resistor can be used to them in 8-bit units with a pull-up resistor option register L (PUOL).

A maximum of 7 out of 8 ports can drive LEDs directly.

RESET input sets port 5 to input mode.

Figure 4-6 shows a block diagram of port 5.

Figure 4-6. P50 to P57 Block Diagram

VDD

PUO

WRPORT

Internal bus

WRPM

PUO5

Selector

Output Latch (P50 to P57)

PM50-PM57

PUO : Pull-up resistor option register PM : Port mode register RD : Port 5 read signal WR : Port 5 write signal

P-ch

P50-P57

CHAPTER 4 PORT FUNCTIONS

4.2.5 Port 7

This is a 3-bit input/output port with output latches. Input mode/output mode can be specified bit-wise by means of port mode register 7 (PM7). When pins P70 to P72 are used as input port pins, an on-chip pull-up resistor can be used as a 3-bit unit by means of pull-up resistor option register L (PUOL).

Dual-functions include serial interface channel 2 data input/output and clock input/output.

RESET input sets the input mode.

Port 7 block diagrams are shown in Figures 4-7 and 4-8.

Caution When used as a serial interface, set the input/output and output latch according to its functions.

For the setting method, refer to Table 11-2 Serial Interface Channel 2 Operating Mode Settings.

Figure 4-7. P70 Block Diagram

VDD

PUO

WRPORT

Internal bus

WRPM

PUO7

Selector

Output Latch

(P70)

PM70

PUO : Pull-up resistor option register PM : Port mode register RD : Port 7 read signal WR : Port 7 write signal

P-ch

P70/SI2/RxD

CHAPTER 4 PORT FUNCTIONS

Figure 4-8. P71 and P72 Block Diagram

VDD

PUO

WRPORT

Internal bus

WRPM

PUO7

Selector

Output Latch (P71 and P72)

PM71, PM72

Alternate Function

PUO : Pull-up resistor option register PM : Port mode register RD : Port 7 read signal WR : Port 7 write signal

P-ch

P71/SO2/TxD, P72/SCK2/ASCK

CHAPTER 4 PORT FUNCTIONS

4.2.6 Port 10

This is an 2-bit input/output port with output latches. Input mode/output mode can be specified bit-wise by means of port mode register 10 (PM10). When pins P100 to P101 are used as input port pins, an on-chip pull-up resistor can be used as an 2-bit unit by means of pull-up resistor option register H (PUOH).

These pins are dual function pins and serve as timer inputs/outputs.

RESET input sets the input mode.

The port 10 block diagram is shown in Figure 4-9.

Figure 4-9. P100 to P101 Block Diagram

VDD

PUO

WRPORT

Internal bus

WRPM

PUO10

Selector

Output Latch (P100 to P101)

PM100 to PM101

Alternate

Functions

PUO : Pull-up resistor option register PM : Port mode register RD : Port 10 read signal WR : Port 10 write signal

P-ch

P100/TI5/TO5, P101/TI6/TO6

CHAPTER 4 PORT FUNCTIONS

4.3 Port Function Control Registers

The following two types of registers control the ports.

• Port mode registers (PM0, PM1, PM3, PM5, PM7, PM10)

• Pull-up resistor option register (PUOH, PUOL)

(1) Port mode registers (PM0, PM1, PM3, PM5, PM7, PM10)

These registers are used to set port input/output in 1-bit units. PM0, PM1, PM3, PM5, PM7, PM10 are independently set with a 1-bit or 8-bit memory manipulation instruction RESET input sets registers to FFH. When port pins are used as the dual-function pins, set the port mode register and output latch according to Table 4-3.

Cautions 1. P00 pin is input-only pin.

2. As port 0 has a dual function as external interrupt request input, when the port function output mode is specified and the output level is changed, the interrupt request flag is set. When the output mode is used, therefore, the interrupt mask flag should be set to 1 beforehand.

CHAPTER 4 PORT FUNCTIONS

Table 4-3. Port Mode Register and Output Latch Settings when Using Dual-Functions

Pin Name

P01 to P03 INTP1 to INTP3 Input 1 × P10 to P17 P35 PCL Output 0 0 P36 BUZ Output 0 0 P100 TI5 Input 1 ×

P101 TI6 Input 1 ×

Note

ANI0 to ANI7 Input 1 ×

TO5 Output 0 0

TO6 Output 0 0

Dual-functions

Name

Input/Output

P××PM××

Note If a read instruction is performed to these pins when they are used as an alternate function, read data is

to be undefined.

Caution When port 7 is used for serial interface, the I/O latch or output latch must be set according to

its function. For the setting methods, see Table 11-2 “Serial Interface Channel 2 Operating Mode Settings.”

Remarks × : don’t care

PM×× : port mode register P×× : port output latch

PM0

CHAPTER 4 PORT FUNCTIONS

Figure 4-10. Port Mode Register Format

76543210Symbol 1 1 PM03 PM02 PM01 1

Address

FF20H

After

Reset

FFH

R/W R/W

PM1

PM17 PM16 PM15 PM14 PM13 PM12 PM11 PM10

PM3

PM37 PM36 PM35 PM34 PM33 PM32 PM31 PM30

PM5

PM57 PM56 PM55 PM54 PM53 PM52 PM51 PM50

PM7

PM10

1 1 1 1 1 PM72 PM71 PM70

111111

PM101PM100

FF21H

FF23H

FF25H

FF27H FFH

FF2AH FFH R/W

Pmn Pin Input/Output Mode Selection

PMmn

(m = 0, 1, 3, 5, 7, 10 : n = 0 to 7) Output mode (output buffer ON)

0 1

Input mode (output buffer OFF)

FFH

R/W

Caution Set 1 to the bits 0, 4 to 7 of PM0, bits 3 to 7 of PM7 and bits 2 to 7 of PM10.

CHAPTER 4 PORT FUNCTIONS

(2) Pull-up resistor option register (PUOH, PUOL)

This register is used to set whether to use an internal pull-up resistor at each port or not. A pull-up resistor is internally used at bits which are set to the input mode at a port where on-chip pull-up resistor use has been specified with PUOH, PUOL. No on-chip pull-up resistors can be used to the bits set to the output mode or to the bits used as an analog input pin, irrespective of PUOH or PUOL setting. PUOH and PUOL are set with a 1-bit or 8-bit memory manipulation instruction. RESET input sets this register to 00H.

Cautions 1. P00 pin does not incorporate a pull-up resistor.

2. When port 1 is used as dual-function pin, an on-chip pull-up resistor cannot be used even if 1 is set in PUOL bit 1 (PUO1).

Figure 4-11. Pull-Up Resistor Option Register Format

After

76 32 0

7654Symbol

76 32 0

7654

PUO7 0 PUO5 0 0 PUO1 PUO0PUOL

0 0 PUO10

PUO3

00PUOH FFF3H 00H R/W

Address

FFF7H 00H R/W

Reset

R/W

PUOm

Pm Internal Pull-up Resistor Selection (m = 0, 1, 3, 5, 7, 10)

Internal pull-up resistor not used

0 1

Internal pull-up resistor used

Caution Set 0 to the bits 0, 1, 3 to 7 of PUOH and bits 2, 4, 6 of PUOL.

CHAPTER 4 PORT FUNCTIONS

4.4 Port Function Operations

Port operations differ depending on whether the input or output mode is set, as shown below.

4.4.1 Writing to input/output port

(1) Output mode

A value is written to the output latch by a transfer instruction, and the output latch contents are output from the pin. Once data is written to the output latch, it is retained until data is written to the output latch again.

(2) Input mode

A value is written to the output latch by a transfer instruction, but since the output buffer is OFF, the pin status does not change. Once data is written to the output latch, it is retained until data is written to the output latch again.

Caution In the case of 1-bit memory manipulation instruction, although a single bit is manipulated

the port is accessed as an 8-bit unit. Therefore, on a port with a mixture of input and output pins, the output latch contents for pins specified as input are undefined except for the manipulated bit.

4.4.2 Reading from input/output port

(1) Output mode

The output latch contents are read by a transfer instruction. The output latch contents do not change.

(2) Input mode

The pin status is read by a transfer instruction. The output latch contents do not change.

4.4.3 Operations on input/output port

(1) Output mode

An operation is performed on the output latch contents, and the result is written to the output latch. The output latch contents are output from the pins. Once data is written to the output latch, it is retained until data is written to the output latch again.

(2) Input mode

The output latch contents are undefined, but since the output buffer is OFF, the pin status does not change.

Caution In the case of 1-bit memory manipulation instruction, although a single bit is manipulated

the port is accessed as an 8-bit unit. Therefore, on a port with a mixture of input and output pins, the output latch contents for pins specified as input are undefined, even for bits other than the manipulated bit.

[MEMO]

CHAPTER 4 PORT FUNCTIONS

CHAPTER 5 CLOCK GENERATOR

5.1 Clock Generator Functions

The clock generator generates the clock to be supplied to the CPU and peripheral hardware. The following type

of system clock oscillator is available.

Main system clock oscillator

This circuit oscillates at frequencies of 1 to 5.0 MHz. Oscillation can be stopped by executing the STOP instruction.

5.2 Clock Generator Configuration

The clock generator consists of the following hardware.

Table 5-1. Clock Generator Configuration

Item Configuration Control register Processor clock control register (PCC)

Oscillation mode selection register (OSMS)

Oscillator Main system clock oscillator

X1 X2

Main System Clock Oscillator

STOP

CHAPTER 5 CLOCK GENERATOR

Figure 5-1. Block Diagram of Clock Generator

Scaler

Selector

f 2

Prescaler

fXX

Selector

Prescaler

Standby Control Circuit

Clock to Peripheral Hardware

CPU Clock (f

CPU)

MCS

Oscillation Mode Selection Register

PCC2

Internal Bus

PCC0

PCC1

Processor Clock Control Register

CHAPTER 5 CLOCK GENERATOR

0 0 0 0 PCC2 PCC1 PCC0PCC FFFBH 04H R/W

7654Symbol

Address

After

Reset R/W

76 32 0

0 0f

PCC2

CPU CIock Selection (f

CPU

)

PCC1 PCC0

0 0

1 0 0

1 1

1 100

fXX/2

Setting prohibitedOther than above

fx/2 (0.8 s)

fx/22(1.6 s)

fx/23(3.2 s)

fx/24(6.4 s)

(0.4 s)

fx/22(1.6 s)

fx/23(3.2 s)

fx/24(6.4 s)

fx/25(12.8 s)

fx /2 (0.8 s)

MCS=1 MCS=0

5.3 Clock Generator Control Register

The clock generator is controlled by the following two registers:

• Processor clock control register (PCC)

• Oscillation mode selection register (OSMS)

(1) Processor clock control register (PCC)

The PCC sets whether to use CPU clock selection and the ratio of division. The PCC is set with a 1-bit or 8-bit memory manipulation instruction. RESET input sets the PCC to 04H.

Figure 5-2. Processor Clock Control Register Format

Caution Set 0 to the bits 3 to 7.

Remarks 1. f

XX : Main system clock frequency (fX or fX/2) X : Main system clock oscillator frequency

2. f

3. MCS : Bit 0 of oscillation mode selection register (OSMS)

4. Figures in parentheses indicate minimum instruction execution time : 2f

X = 5.0 MHz.

at f

CPU when operating

CHAPTER 5 CLOCK GENERATOR

(2) Oscillation mode selection register (OSMS)

This register specifies whether the clock output from the main system clock oscillator without passing through the scaler is used as the main system clock, or the clock output via the scaler is used as the main system clock. OSMS is set with 8-bit memory manipulation instruction. RESET input sets OSMS to 00H.

Figure 5-3. Oscillation Mode Selection Register Format

765432Symbol 000 0OSMS FFF2H

0 MCS

Address

Main System Clock Scaler Control

MCS

Scaler used

0 1

Scaler not used

After

Reset

00H W

R/W

Cautions 1. Writing to OSMS should be performed only immediately after reset signal release and before

peripheral hardware operation starts. As shown in Figure 5-4 below, writing data (including same data as previous) to OSMS cause delay of main system clock cycle up to 2/f

x during

the write operation. Therefore, if this register is written during the operation, in peripheral hardware which operates with the main system clock, a temporary error occurs in the count clock cycle of timer, etc. In addition, because the oscillation mode is changed by this register, the clocks for peripheral hardware as well as that for the CPU are switched.

Figure 5-4. Main System Clock Waveform due to Writing to OSMS

Write to OSMS

(MCS 0)

Max. 2/fX

fXX

Remarks f

Operating at fXX = fX/2 (MCS = 0) Operating at fXX = fX/2 (MCS = 0)

2. When writing “1” to MCS, V

xx : Main system clock frequency (fx or fx/2) x : Main system clock oscillation frequency

DD must be 2.7 V or higher before the write execution.

CHAPTER 5 CLOCK GENERATOR

5.4 System Clock Oscillator

5.4.1 Main system clock oscillator

The main system clock oscillator oscillates with a crystal resonator or a ceramic resonator (standard: 5.0 MHz)

connected to the X1 and X2 pins.

External clocks can be input to the main system clock oscillator. In this case, input a clock signal to the X1 pin

and an antiphase clock signal to the X2 pin.

Figure 5-5 shows an external circuit of the main system clock oscillator.

Figure 5-5. External Circuit of Main System Clock Oscillator

(a) Crystal and ceramic oscillation (b) External clock

Crystal or Ceramic Resonator

IC X2

External Clock

PD74HCU04

Cautions 1. Do not execute the STOP instruction if an external clock is used. This is because the X2 pin

is connected to V

DD via a pull-up register.

2. When using a main system clock oscillator, carry out wiring in the broken line area in Figure 5-5 to prevent any effects from wiring capacities.

● Minimize the wiring length.

● Do not allow wiring to intersect with other signal conductors. Do not allow wiring to come

near changing high current.

● Set the potential of the grounding position of the oscillator capacitor to that of VSS. Do

not ground to any ground pattern where high current is present.

● Do not fetch signals from the oscillator.

Figure 5-6 shows examples of oscillator having bad connection.

CHAPTER 5 CLOCK GENERATOR

Figure 5-6. Examples of Oscillator with Bad Connection (1/2)

(a) Wiring of connection circuits (b) Signal conductors intersect

is too long with each other

PORTn

X2 X1

IC X2 X1

(n = 0, 1, 3, 5, 7, 10)

signal conductor of the ocsillator (potential at points A, B,

and C fluctuate)

IC X2 X1

High Current

IC X2

AB C

High Current

Pnm

Figure 5-6. Examples of Oscillator with Bad Connection (2/2)

IC X2 X1

CHAPTER 5 CLOCK GENERATOR

5.4.2 Scaler

The scaler divides the main system clock oscillator output (fXX) and generates various clocks.

CHAPTER 5 CLOCK GENERATOR

5.5 Clock Generator Operations

The clock generator generates the following various types of clocks and controls the CPU operating mode

including the standby mode.

• Main system clock fXX

• CPU clock fCPU

• Clock to peripheral hardware

The following clock generator functions and operations are determined with the processor clock control register

(PCC) and the oscillation mode selection register (OSMS).

(a) Upon generation of RESET signal, the lowest speed mode of the main system clock (12.8

at 5.0 MHz) is selected (PCC = 04H, OSMS = 00H). Main system clock oscillation stops while low level is applied to RESET pin.

(b) The six types of CPU clocks (0.4

the PCC and OSMS.

s. 0.8 µs, 1.6 µs, 3.2 µs, 6.4µs, 12.8 µs : 5.0 MHz) can be selected by setting

s when operated

(d) The main system clock is divided and supplied to the peripheral hardware. Thus, the peripheral hardware

also stops if the main system clock is stopped. (Except external input clock operation)

CHAPTER 5 CLOCK GENERATOR

5.6 Changing CPU Clock Settings

5.6.1 Time required for CPU clock switchover

The CPU clock can be switched over by means of bits 0 to 2 (PCC0 to PCC2) of the processor clock control register

(PCC).

The actual switchover operation is not performed directly after writing to the PCC, but operation continues on the

pre-switchover clock for several instructions (see Table 5-2).

Table 5-2. Maximum Time Required for CPU Clock Switchover

Set Values before Switchover

PCC0PCC2 PCC1

000 16 instructions 16 instructions 16 instructions 16 instructions

011

8 instructions

4 instructions 4 instructions

2 instructions

1 instruction 1 instruction1 instruction

Set Values After Switchover

8 instructions 8 instructions

2 instructions

8 instructions

4 instructions 4 instructions

1 instruction

PCC1PCC2 PCC0PCC1PCC2 PCC0PCC1PCC2 PCC0PCC1PCC2 PCC0PCC1PCC2 PCC0

100110100100000

2 instructions

Remark One instruction is the minimum instruction execution time with the pre-switchover CPU clock.

IBM PD78P083-A, PD78083, uPD78081, uPD78082-A, uPD78P083-A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

PREFACE

1.1 Features

CHAPTER 1 OUTLINE

1.2 Applications

1.3 Ordering Information

1.4 Quality Grade

1.5 Pin Configuration (Top View)

1.6 78K/0 Series Development

1.7 Block Diagram

1.8 Outline of Function

2.1 Pin Function List

2.1.1 Normal operating mode pins

CHAPTER 2 PIN FUNCTION

2.2 Description of Pin Functions

2.2.1 P00 to P03 (Port 0)

2.2.2 P10 to P17 (Port 1)

2.2.3 P30 to P37 (Port 3)

2.2.4 P50 to P57 (Port 5)

2.2.5 P70 to P72 (Port 7)

2.2.6 P100 to P101 (Port 10)

2.2.7 AVREF

2.2.9 AVSS

2.2.11 X1 and X2

2.2.15 IC (Mask ROM version only)

2.2.16 NC (44-pin plastic QFP versions only)

2.3 Pin Input/Output Circuits and Recommended Connection of Unused Pins

3.1 Memory Spaces

CHAPTER 3 CPU ARCHITECTURE

3.1.1 Internal program memory space

3.1.2 Internal data memory space

3.1.3 Special Function Register (SFR) area

3.1.4 Data memory addressing

3.2 Processor Registers

3.2.1 Control registers

3.2.2 General registers

3.2.3 Special Function Register (SFR)

3.3 Instruction Address Addressing

3.3.1 Relative addressing

3.3.2 Immediate addressing

3.3.3 Table indirect addressing

3.3.4 Register addressing

3.4 Operand Address Addressing

3.4.1 Implied addressing

3.4.2 Register addressing

3.4.3 Direct addressing

3.4.4 Short direct addressing

3.4.5 Special-Function Register (SFR) addressing

3.4.6 Register indirect addressing

3.4.7 Based addressing

3.4.8 Based indexed addressing

3.4.9 Stack addressing

CHAPTER 4 PORT FUNCTIONS

4.1 Port Functions

4.2 Port Configuration

4.2.1 Port 0

4.2.2 Port 1

4.2.3 Port 3

4.2.4 Port 5

4.2.5 Port 7

4.2.6 Port 10

4.3 Port Function Control Registers

4.4 Port Function Operations

4.4.1 Writing to input/output port

4.4.2 Reading from input/output port

4.4.3 Operations on input/output port

CHAPTER 5 CLOCK GENERATOR

5.1 Clock Generator Functions

5.2 Clock Generator Configuration

5.3 Clock Generator Control Register

5.4 System Clock Oscillator

5.4.1 Main system clock oscillator

5.4.2 Scaler

5.5 Clock Generator Operations

5.6 Changing CPU Clock Settings

5.6.1 Time required for CPU clock switchover