IBM 9040-MR9 User Manual

Download

Page 1

Power Systems

Vital product data card for the 9040MR9

IBM

Page 2

Note

Before using this information and the product it supports, read the information in “Safety notices” on page v, “Notices” on page 15, the IBM Systems Safety Notices manual, G229-9054, and the IBM Environmental Notices and User Guide, Z125–5823.

This edition applies to IBM® Power Systems servers that contain the POWER9™ processor and to all associated models.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.

Page 3

Contents

Safety notices........................................................................................................v

Vital product data card.......................................................................................... 1

Removing and replacing the vital product data card.................................................................................. 1

Preparing the system..............................................................................................................................1

Removing the vital product data card....................................................................................................8

Replacing the vital product data card....................................................................................................9

Preparing the system for operation..................................................................................................... 10

Notices................................................................................................................15

Accessibility features for IBM Power Systems servers............................................................................ 16

Privacy policy considerations ................................................................................................................... 17

Trademarks................................................................................................................................................ 17

Electronic emission notices.......................................................................................................................17

Class A Notices.....................................................................................................................................18

Class B Notices.....................................................................................................................................21

Terms and conditions.................................................................................................................................23

iii

Page 4

Page 5

Safety notices

Safety notices may be printed throughout this guide:

• DANGER notices call attention to a situation that is potentially lethal or extremely hazardous to people.

• CAUTION notices call attention to a situation that is potentially hazardous to people because of some existing condition.

• Attention notices call attention to the possibility of damage to a program, device, system, or data.

World Trade safety information

Several countries require the safety information contained in product publications to be presented in their national languages. If this requirement applies to your country, safety information documentation is included in the publications package (such as in printed documentation, on DVD, or as part of the product) shipped with the product. The documentation contains the safety information in your national language with references to the U.S. English source. Before using a U.S. English publication to install, operate, or service this product, you must rst become familiar with the related safety information documentation. You should also refer to the safety information documentation any time you do not clearly understand any safety information in the U.S. English publications.

Replacement or additional copies of safety information documentation can be obtained by calling the IBM Hotline at 1-800-300-8751.

German safety information

Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der Bildschirmarbeitsverordnung geeignet.

Laser safety information

IBM servers can use I/O cards or features that are ber-optic based and that utilize lasers or LEDs.

Laser compliance

IBM servers may be installed inside or outside of an IT equipment rack.

DANGER:

Electrical voltage and current from power, telephone, and communication cables are hazardous. To avoid a shock hazard:

• If IBM supplied the power cord(s), connect power to this unit only with the IBM provided power cord. Do not use the IBM provided power cord for any other product.

• Do not open or service any power supply assembly.

• Do not connect or disconnect any cables or perform installation, maintenance, or reconguration of this product during an electrical storm.

• The product might be equipped with multiple power cords. To remove all hazardous voltages, disconnect all power cords.

– For AC power, disconnect all power cords from their AC power source. – For racks with a DC power distribution panel (PDP), disconnect the customer’s DC power

• When connecting power to the product ensure all power cables are properly connected.

When working on or around the system, observe the following precautions:

source to the PDP.

– For racks with AC power, connect all power cords to a properly wired and grounded electrical

outlet. Ensure that the outlet supplies proper voltage and phase rotation according to the system rating plate.

Page 6

– For racks with a DC power distribution panel (PDP), connect the customer’s DC power source

to the PDP. Ensure that the proper polarity is used when attaching the DC power and DC power return wiring.

• Connect any equipment that will be attached to this product to properly wired outlets.

• When possible, use one hand only to connect or disconnect signal cables.

• Never turn on any equipment when there is evidence of re, water, or structural damage.

• Do not attempt to switch on power to the machine until all possible unsafe conditions are corrected.

• Assume that an electrical safety hazard is present. Perform all continuity, grounding, and power checks specied during the subsystem installation procedures to ensure that the machine meets safety requirements.

• Do not continue with the inspection if any unsafe conditions are present.

• Before you open the device covers, unless instructed otherwise in the installation and conguration procedures: Disconnect the attached AC power cords, turn off the applicable circuit breakers located in the rack power distribution panel (PDP), and disconnect any telecommunications systems, networks, and modems.

DANGER:

• Connect and disconnect cables as described in the following procedures when installing, moving, or opening covers on this product or attached devices.

To Disconnect:

1. Turn off everything (unless instructed otherwise).

2. For AC power, remove the power cords from the outlets.

3. For racks with a DC power distribution panel (PDP), turn off the circuit breakers located in the PDP and remove the power from the Customer's DC power source.

4. Remove the signal cables from the connectors.

5. Remove all cables from the devices.

To Connect:

1. Turn off everything (unless instructed otherwise).

2. Attach all cables to the devices.

3. Attach the signal cables to the connectors.

4. For AC power, attach the power cords to the outlets.

5. For racks with a DC power distribution panel (PDP), restore the power from the Customer's DC power source and turn on the circuit breakers located in the PDP.

6. Turn on the devices.

Sharp edges, corners and joints may be present in and around the system. Use care when handling equipment to avoid cuts, scrapes and pinching. (D005)

(R001 part 1 of 2):

DANGER:

• Heavy equipment–personal injury or equipment damage might result if mishandled.

• Always lower the leveling pads on the rack cabinet.

• Always install stabilizer brackets on the rack cabinet unless the earthquake option is to be installed.

• To avoid hazardous conditions due to uneven mechanical loading, always install the heaviest devices in the bottom of the rack cabinet. Always install servers and optional devices starting from the bottom of the rack cabinet.

Observe the following precautions when working on or around your IT rack system:

vi Power Systems: Vital product data card for the 9040-MR9

Page 7

• Rack-mounted devices are not to be used as shelves or work spaces. Do not place objects on top of rack-mounted devices. In addition, do not lean on rack mounted devices and do not use them to stabilize your body position (for example, when working from a ladder).

• Each rack cabinet might have more than one power cord.

– For AC powered racks, be sure to disconnect all power cords in the rack cabinet when directed

to disconnect power during servicing.

– For racks with a DC power distribution panel (PDP), turn off the circuit breaker that controls

the power to the system unit(s), or disconnect the customer’s DC power source, when directed to disconnect power during servicing.

• Connect all devices installed in a rack cabinet to power devices installed in the same rack cabinet. Do not plug a power cord from a device installed in one rack cabinet into a power device installed in a different rack cabinet.

• An electrical outlet that is not correctly wired could place hazardous voltage on the metal parts of the system or the devices that attach to the system. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (R001 part 1 of 2)

(R001 part 2 of 2):

CAUTION:

• Do not install a unit in a rack where the internal rack ambient temperatures will exceed the manufacturer's recommended ambient temperature for all your rack-mounted devices.

• Do not install a unit in a rack where the air flow is compromised. Ensure that air flow is not blocked or reduced on any side, front, or back of a unit used for air flow through the unit.

• Consideration should be given to the connection of the equipment to the supply circuit so that overloading of the circuits does not compromise the supply wiring or overcurrent protection. To provide the correct power connection to a rack, refer to the rating labels located on the equipment in the rack to determine the total power requirement of the supply circuit.

• (For sliding drawers.) Do not pull out or install any drawer or feature if the rack stabilizer brackets are not attached to the rack or if the rack is not bolted to the floor. Do not pull out more than one drawer at a time. The rack might become unstable if you pull out more than one drawer at a time.

• (For xed drawers.) This drawer is a xed drawer and must not be moved for servicing unless specied by the manufacturer. Attempting to move the drawer partially or completely out of the rack might cause the rack to become unstable or cause the drawer to fall out of the rack. (R001 part 2 of 2)

CAUTION:

Removing components from the upper positions in the rack cabinet improves rack stability during relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a room or building.

• Reduce the weight of the rack cabinet by removing equipment starting at the top of the rack

cabinet. When possible, restore the rack cabinet to the conguration of the rack cabinet as you received it. If this conguration is not known, you must observe the following precautions:

Safety notices vii

Page 8

– Remove all devices in the 32U position (compliance ID RACK-001 or 22U (compliance ID

RR001) and above. – Ensure that the heaviest devices are installed in the bottom of the rack cabinet. – Ensure that there are little-to-no empty U-levels between devices installed in the rack cabinet

below the 32U (compliance ID RACK-001 or 22U (compliance ID RR001) level, unless the

received conguration specically allowed it.

• If the rack cabinet you are relocating is part of a suite of rack cabinets, detach the rack cabinet from the suite.

• If the rack cabinet you are relocating was supplied with removable outriggers they must be reinstalled before the cabinet is relocated.

• Inspect the route that you plan to take to eliminate potential hazards.

• Verify that the route that you choose can support the weight of the loaded rack cabinet. Refer to the documentation that comes with your rack cabinet for the weight of a loaded rack cabinet.

• Verify that all door openings are at least 760 x 230 mm (30 x 80 in.).

• Ensure that all devices, shelves, drawers, doors, and cables are secure.

• Ensure that the four leveling pads are raised to their highest position.

• Ensure that there is no stabilizer bracket installed on the rack cabinet during movement.

• Do not use a ramp inclined at more than 10 degrees.

• When the rack cabinet is in the new location, complete the following steps:

– Lower the four leveling pads. – Install stabilizer brackets on the rack cabinet or in an earthquake environment bolt the rack to

the floor.

– If you removed any devices from the rack cabinet, repopulate the rack cabinet from the lowest

position to the highest position.

• If a long-distance relocation is required, restore the rack cabinet to the conguration of the rack cabinet as you received it. Pack the rack cabinet in the original packaging material, or equivalent. Also lower the leveling pads to raise the casters off of the pallet and bolt the rack cabinet to the pallet.

(L001)

(L002)

(R002)

DANGER:

Hazardous voltage, current, or energy levels are present inside any component that has

this label attached. Do not open any cover or barrier that contains this label. (L001)

viii

Power Systems: Vital product data card for the 9040-MR9

Page 9

(L003)

DANGER: Rack-mounted devices are not to be used as shelves or work spaces. Do not place objects on top of rack-mounted devices. In addition, do not lean on rack-mounted devices and do not use them to stabilize your body position (for example, when working from a ladder). (L002)

Safety notices

Page 10

(L007)

DANGER: Multiple power cords. The product might be equipped with multiple AC power cords or

multiple DC power cables. To remove all hazardous voltages, disconnect all power cords and power cables. (L003)

CAUTION:

A hot surface nearby. (L007)

(L008)

CAUTION:

Hazardous moving parts nearby. (L008)

All lasers are certied in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class 1 laser products. Outside the U.S., they are certied to be in compliance with IEC 60825 as a class 1 laser product. Consult the label on each part for laser certication numbers and approval information.

CAUTION:

This product might contain one or more of the following devices: CD-ROM drive, DVDROM drive, DVD-RAM drive, or laser module, which are Class 1 laser products. Note the following information:

• Do not remove the covers. Removing the covers of the laser product could result in exposure to

hazardous laser radiation. There are no serviceable parts inside the device.

• Use of the controls or adjustments or performance of procedures other than those specied

herein might result in hazardous radiation exposure.

x Power Systems: Vital product data card for the 9040-MR9

Page 11

(C026)

CAUTION: Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical ber cable or open receptacle. Although shining light into one end and looking into the other end of a disconnected optical ber to verify the continuity of optic bers may not injure the eye, this procedure is potentially dangerous. Therefore, verifying the continuity of optical bers by shining light into one end and looking at the other end is not recommended. To verify continuity of a ber optic cable, use an optical light source and power meter. (C027)

CAUTION: This product contains a Class 1M laser. Do not view directly with optical instruments. (C028)

CAUTION: Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following information:

• Laser radiation when open.

• Do not stare into the beam, do not view directly with optical instruments, and avoid direct

exposure to the beam. (C030)

(C030)

CAUTION: The battery contains lithium. To avoid possible explosion, do not burn or charge the battery.

Do Not:

• Throw or immerse into water

• Heat to more than 100 degrees C (212 degrees F)

• Repair or disassemble

Exchange only with the IBM-approved part. Recycle or discard the battery as instructed by local regulations. In the United States, IBM has a process for the collection of this battery. For information, call 1-800-426-4333. Have the IBM part number for the battery unit available when you call. (C003)

CAUTION: Regarding IBM provided VENDOR LIFT TOOL:

• Operation of LIFT TOOL by authorized personnel only.

• LIFT TOOL intended for use to assist, lift, install, remove units (load) up into rack elevations. It is

not to be used loaded transporting over major ramps nor as a replacement for such designated tools like pallet jacks, walkies, fork trucks and such related relocation practices. When this is not practicable, specially trained persons or services must be used (for instance, riggers or movers).

• Read and completely understand the contents of LIFT TOOL operator's manual before using.

Failure to read, understand, obey safety rules, and follow instructions may result in property damage and/or personal injury. If there are questions, contact the vendor's service and support. Local paper manual must remain with machine in provided storage sleeve area. Latest revision manual available on vendor's web site.

• Test verify stabilizer brake function before each use. Do not over-force moving or rolling the LIFT

TOOL with stabilizer brake engaged.

• Do not raise, lower or slide platform load shelf unless stabilizer (brake pedal jack) is fully

engaged. Keep stabilizer brake engaged when not in use or motion.

• Do not move LIFT TOOL while platform is raised, except for minor positioning.

• Do not exceed rated load capacity. See LOAD CAPACITY CHART regarding maximum loads at

center versus edge of extended platform.

• Only raise load if properly centered on platform. Do not place more than 200 lb (91 kg) on edge

of sliding platform shelf also considering the load's center of mass/gravity (CoG).

• Do not corner load the platforms, tilt riser, angled unit install wedge or other such accessory

options. Secure such platforms -- riser tilt, wedge, etc options to main lift shelf or forks in all four

Safety notices

Page 12

(4x or all other provisioned mounting) locations with provided hardware only, prior to use. Load objects are designed to slide on/off smooth platforms without appreciable force, so take care not to push or lean. Keep riser tilt [adjustable angling platform] option flat at all times except for nal minor angle adjustment when needed.

• Do not stand under overhanging load.

• Do not use on uneven surface, incline or decline (major ramps).

• Do not stack loads.

• Do not operate while under the influence of drugs or alcohol.

• Do not support ladder against LIFT TOOL (unless the specic allowance is provided for one

following qualied procedures for working at elevations with this TOOL).

• Tipping hazard. Do not push or lean against load with raised platform.

• Do not use as a personnel lifting platform or step. No riders.

• Do not stand on any part of lift. Not a step.

• Do not climb on mast.

• Do not operate a damaged or malfunctioning LIFT TOOL machine.

• Crush and pinch point hazard below platform. Only lower load in areas clear of personnel and

obstructions. Keep hands and feet clear during operation.

• No Forks. Never lift or move bare LIFT TOOL MACHINE with pallet truck, jack or fork lift.

• Mast extends higher than platform. Be aware of ceiling height, cable trays, sprinklers, lights, and

other overhead objects.

• Do not leave LIFT TOOL machine unattended with an elevated load.

• Watch and keep hands, ngers, and clothing clear when equipment is in motion.

• Turn Winch with hand power only. If winch handle cannot be cranked easily with one hand, it is

probably over-loaded. Do not continue to turn winch past top or bottom of platform travel. Excessive unwinding will detach handle and damage cable. Always hold handle when lowering, unwinding. Always assure self that winch is holding load before releasing winch handle.

• A winch accident could cause serious injury. Not for moving humans. Make certain clicking sound

is heard as the equipment is being raised. Be sure winch is locked in position before releasing handle. Read instruction page before operating this winch. Never allow winch to unwind freely. Freewheeling will cause uneven cable wrapping around winch drum, damage cable, and may cause serious injury.

• This TOOL must be maintained correctly for IBM Service personnel to use it. IBM shall inspect

condition and verify maintenance history before operation. Personnel reserve the right not to use TOOL if inadequate. (C048)

Power and cabling information for NEBS (Network Equipment-Building System) GR-1089-CORE

The following comments apply to the IBM servers that have been designated as conforming to NEBS (Network Equipment-Building System) GR-1089-CORE:

The equipment is suitable for installation in the following:

• Network telecommunications facilities

• Locations where the NEC (National Electrical Code) applies

The intrabuilding ports of this equipment are suitable for connection to intrabuilding or unexposed wiring or cabling only. The intrabuilding ports of this equipment must not be metallically connected to the interfaces that connect to the OSP (outside plant) or its wiring. These interfaces are designed for use as intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling. The addition of primary protectors is not sufcient protection to connect these interfaces metallically to OSP wiring.

Note: All Ethernet cables must be shielded and grounded at both ends.

xii

Power Systems: Vital product data card for the 9040-MR9

Page 13

The ac-powered system does not require the use of an external surge protection device (SPD).

The dc-powered system employs an isolated DC return (DC-I) design. The DC battery return terminal shall not be connected to the chassis or frame ground.

The dc-powered system is intended to be installed in a common bonding network (CBN) as described in GR-1089-CORE.

Safety notices xiii

Page 14

xiv Power Systems: Vital product data card for the 9040-MR9

Page 15

Vital product data card for the 9040-MR9

Find information about removing and replacing a vital product data (VPD) card in the system.

Removing and replacing the vital product data card in the 9040-MR9

Find information about removing and replacing the vital product data (VPD) card in the system.

Note: Removing or replacing this part is a customer task. You can complete this task yourself, or contact a service provider to complete the task for you. You might be charged a fee by the service provider for this service.

If your system is managed by the Hardware Management Console (HMC), use the HMC to repair a part in the system. For instructions, see Repairing a part by using the HMC (www.ibm.com/support/ knowledgecenter/POWER9/p9haj/p9haj_hmc_repair.htm).

If your system is not managed by an HMC, complete the steps in following procedures to remove and replace the VPD card.

Preparing the system to remove and replace the vital product data card from the 9040MR9

To prepare the system to remove and replace the vital product data card, complete the steps in this procedure.

About this task

Note: If you plan to replace the VPD card and have the replacement card, you can contact the following

email address from 8 AM to 5 PM US Central Time, Monday to Friday, to obtain the replacement activation codes before repair. You must supply the machine type and serial number, and the part number and serial number of the replacement VPD card. If you use the AIX® or Linux operating systems, contact pcod@us.ibm.com. If you use the IBM i operating system, contact icod@us.ibm.com.

Procedure

1. Identify the part and the system that you are working on. For instructions, see Identifying a part (www.ibm.com/support/knowledgecenter/POWER9/p9haj/sal.htm).

Use the blue identify LED on the enclosure to locate the system. Ensure that the serial number of the system matches the serial number to be serviced.

2. Stop the system. For instructions, see Stopping a system (www.ibm.com/support/knowledgecenter/ POWER9/p9haj/crustopsys.htm).

3. Access the ASMI.

If you are already connected to the ASMI, go to the next step.

a) For instructions, see Accessing the ASMI without an HMC (www.ibm.com/support/

knowledgecenter/POWER9/p9hby/connect_asmi.htm). b) Click Tasks. c) Click Operations > Launch Advanced System Management (ASM).

4. Record the system identiers.

Note: To perform this operation, your authority level must be administrator or authorized service provider.

a) In the ASMI Welcome page, if you have not already logged in, specify your user ID and password,

and click Log in. b) In the navigation area, expand System Conguration > Program Vital Product Data.

Page 16

c) Select System Brand under Program Vital Product Data. d) Manually record the value for the system brand, which appears in the right pane. e) In the navigation area, select System Keywords under Program Vital Product Data.

f) Manually record all of the values, such as the Machine type-model, System serial number, and

System unique ID. Also, if applicable, record the activation codes, which are shown in the topic

pane.

Notes:

1) If you do not know the system unique ID, contact your next level of support.

2) You cannot boot the system until valid values are entered for all elds.

3) You can change these entries only once.

5. Attach the electrostatic discharge (ESD) wrist strap. The ESD wrist strap must be connected to an unpainted metal surface until the service procedure is

completed, and if applicable, until the service access cover is replaced.

Attention:

• Attach an electrostatic discharge (ESD) wrist strap to the front ESD jack, to the rear ESD jack, or to an unpainted metal surface of your hardware to prevent the electrostatic discharge from damaging your hardware.

• When you use an ESD wrist strap, follow all electrical safety procedures. An ESD wrist strap is used for static control. It does not increase or decrease your risk of receiving electric shock when using or working on electrical equipment.

• If you do not have an ESD wrist strap, just prior to removing the product from ESD packaging and installing or replacing hardware, touch an unpainted metal surface of the system for a minimum of 5 seconds. If at any point in this service process you move away from the system, it is important to again discharge yourself by touching an unpainted metal surface for at least 5 seconds before you continue with the service process.

6. Label and disconnect the power source from the system by unplugging the power cords from the system.

Notes:

• This system might be equipped with two or more power supplies. If the removing and replacing

procedures require the system power to be turned off, ensure that all power sources to the system are disconnected.

• The power cord (B) is fastened to the system with a hook-and-loop fastener (A). If you are placing

the system in a service position after you disconnect the power cords, ensure that you unstrap the fastener.

Power Systems: Vital product data card for the 9040-MR9

Page 17

Figure 1. Removing the power cords

(L003)

Vital product data card for the 9040-MR9

Page 18

DANGER:

Multiple power cords. The product might be equipped with multiple AC power cords or multiple DC power cables. To remove all hazardous voltages, disconnect all power cords and power cables. (L003)

7. Label and disconnect all external cables that are attached to the PCIe adapters.

8. Complete the following steps to place the system in the service position.

Power Systems: Vital product data card for the 9040-MR9

Page 19

Do not pull out or install any drawer or feature if the rack stabilizer brackets are not attached to the rack. Do not pull out more than one drawer at a time. The rack might become unstable if you pull out more than one drawer at a time.

a. If not already removed, remove the shipping screws (A) as shown in the following gure by using a

Phillips screwdriver.

b. Release the side latches (B) by pressing them downward as shown in the following gure.

c. Pull out the system (C) as shown in the following gure. Ensure that any cables do not catch or

bind as you pull out the system.

Figure 2. Placing the system in service position

9. Remove the service access cover.

Vital product data card for the 9040-MR9

Page 20

Attention: Operating the system without the cover for more than 10 minutes might damage

the system components. For proper cooling and airflow, replace the cover before turning on the system.

a. Push the release latches (A) in the direction shown in the following gure. b. Slide the cover (B) off the system unit as shown in the following gure. When the front of the

service access cover has cleared the upper frame ledge, lift the cover up and off the system unit.

Figure 3. Removing the service access cover

10. To activate the identify LED for the faulty part, press and hold push-button (A) on the trusted platform module card as shown in the following gure.

Verify that the green LED (B) is lit, which indicates that sufcient power exists for the identify LED. If the LED (B) is not lit, use the location code to nd the physical location by using the service label.

Power Systems: Vital product data card for the 9040-MR9

Page 21

Figure 4. Activating the identify LED

11. Look for the flashing amber LED of the vital product data card. Refer to the following image.

Vital product data card for the 9040-MR9

Page 22

Figure 5. Location of the vital product data card service indicator LED

Removing the vital product data card from the 9040-MR9

Follow these steps to remove the vital product data card.

Procedure

1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged

into a ground jack or connected to an unpainted metal surface. If not, do so now.

2. Remove the VPD card.

a) Grasp the VPD card by the plastic housing. Refer to the following image.

Tip: You might nd it helpful to unplug the USB cable from the system backplane and route it over the side of the system so that you have more space to grasp the VPD card.

b) Pull the VPD card out of its slot on the system backplane.

Power Systems: Vital product data card for the 9040-MR9

Page 23

Figure 6. Removing the VPD card

Replacing the vital product data card in the 9040-MR9

Follow these steps to replace the vital product data card.

Procedure

1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged

into a ground jack or connected to an unpainted metal surface. If not, do so now.

2. Replace the VPD card.

a) Align the VPD card in its slot on the system backplane. Refer to the following image. b) Push the VPD card into place until it is fully seated.

Remember: If you unplugged the USB cable so that you could access the VPD card, don't forget to reconnect it.

Vital product data card for the 9040-MR9

Page 24

Figure 7. Replacing the VPD card

Preparing the system for operation after removing and replacing the VPD card from the 9040-MR9

Follow these steps to prepare the system for operation after removing and replacing the vital product data card.

Procedure

1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged into a ground jack or connected to an unpainted metal surface. If not, do so now.

2. Replace the service access cover.

a) Lower the cover (A) onto the system unit. Ensure that the cover alignment pins (C) on each side of

the cover t into the matching slots in the chassis.

b) Slide the cover (A) onto the system unit. Ensure that the tabs (D) tuck under the mesh along the

front opening of the chassis.

c) Close the release latches (B) by pushing it in the direction that is shown in the following gure.

Power Systems: Vital product data card for the 9040-MR9

Page 25

Figure 8. Installing the service access cover

3. Complete the following steps to place the system in the operating position.

a. Unlock the blue rail safety latches (A) by pushing them towards the front as shown in the following

gure.

b. Push the system unit back into the rack as shown in the following gure until both release latches

of the system unit lock into position. Ensure that any cables do not catch or bind as you push in the system.

Note: Slide the system unit slowly into the rack to ensure that your ngers do not get caught in the side rails.

Vital product data card for the 9040-MR9

Page 26

Figure 9. Placing the system into the operating position

4. Using your labels, reconnect all of the external cables that plug into the PCIe adapters.

5. Using your labels, reconnect the power cords (A) to the system unit as shown in the following gure. Fasten the power cords to the system by using the hook-and-loop fasteners (B) as shown in the

following gure.

Power Systems: Vital product data card for the 9040-MR9

Page 27

Figure 10. Connecting the power cords

6. When the service processor comes up to the standby state (the power-on LED on the control panel is flashing slowly), continue to the next step.

7. Turn off the identify LED. For instructions, see Deactivating an identify LED (www.ibm.com/support/ knowledgecenter/POWER9/p9haj/p9haj_turn_off_identify_led.htm).

8. Access the ASMI.

If you are already connected to the ASMI, go to the next step.

a) For instructions, see Accessing the ASMI without an HMC (www.ibm.com/support/

knowledgecenter/POWER9/p9hby/connect_asmi.htm). b) Click Tasks. c) Click Operations > Launch Advanced System Management (ASM).

9. In the ASMI navigation panel, expand Power/Restart Control > Power On/Off System. Clear Server rmware start policy and select Standby (User-Initiated). Then, click Save settings.

10. Set the system identiers and the activation codes for the Capacity on Demand (CoD) and Virtualization Engine technologies (VET):

Note: To perform this operation, your authority level must be administrator or authorized service provider.

a) In the navigation area, expand System Conguration > Program Vital Product Data.

Vital product data card for the 9040-MR9

Page 28

b) Click System Brand.

Note: If you do not know the correct system brand, contact your next level of support.

c) If the system brand matches what you recorded previously, click Accept backed up setting and

save the settings. Otherwise, enter the correct system brand and click Continue. d) Click Save setting to update the system brand to the VPD. e) Click System Keywords.

Note: If you do not know the system unique ID, contact your next level of support. You cannot

boot the system until valid values are entered for all elds. You can change these entries only

once.

f) If the system keywords match what you recorded previously, click Accept backed up setting and

save the settings. Otherwise, enter the values for the machine type, model number, system serial

number, system unique ID, and RB Keyword. g) Click Save settings to update the system keywords and to save them to the VPD. h) In the ASMI navigation panel, expand Power/Restart Control > Power On/Off System. Click

Server rmware start policy and select Standby. Then, click Save settings and continue power

on.

i) In the ASMI navigation panel, expand On demand Utilities > CoD Activation. Enter the CoD code

and click Continue to write the CoD code to VPD. Repeat this step for all of the COD and VET

codes.

j) In the ASMI navigation panel, expand Power/Restart Control > Power On/Off System. Click

Server rmware start policy and select Running (Auto-Start Always). Then, click Save settings

and continue power on.

11. Verify the installed part.

• If you replaced the part because of a service action, verify the installed part. For instructions, see https://www.ibm.com/support/knowledgecenter/POWER9/p9ect/ pxect_verifyrepair.htm (www.ibm.com/support/knowledgecenter/POWER9/p9ect/ pxect_verifyrepair.htm).

• If you installed the part for any other reason, verify the installed part. For instructions, see https:// www.ibm.com/support/knowledgecenter/POWER9/p9haj/pxhaj_hsmverify.htm (www.ibm.com/ support/knowledgecenter/POWER9/p9haj/pxhaj_hsmverify.htm).

Power Systems: Vital product data card for the 9040-MR9

Page 29

Notices

This information was developed for products and services offered in the US.

IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead. However, it is the user's responsibility to evaluate and verify the operation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not grant you any license to these patents. You can send license inquiries, in writing, to:

IBM Director of Licensing IBM Corporation North Castle Drive, MD-NC119 Armonk, NY 10504-1785 US

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice.

Any references in this information to non-IBM websites are provided for convenience only and do not in any manner serve as an endorsement of those websites. The materials at those websites are not part of the materials for this IBM product and use of those websites is at your own risk.

IBM may use or distribute any of the information you provide in any way it believes appropriate without incurring any obligation to you.

The performance data and client examples cited are presented for illustrative purposes only. Actual performance results may vary depending on specic congurations and operating conditions.

Information concerning non-IBM products was obtained from the suppliers of those products, their published announcements or other publicly available sources. IBM has not tested those products and cannot conrm the accuracy of performance, compatibility or any other claims related to non-IBM products. Questions on the capabilities of non-IBM products should be addressed to the suppliers of those products.

Statements regarding IBM's future direction or intent are subject to change or withdrawal without notice, and represent goals and objectives only.

All IBM prices shown are IBM's suggested retail prices, are current and are subject to change without notice. Dealer prices may vary.

This information is for planning purposes only. The information herein is subject to change before the products described become available.

This information contains examples of data and reports used in daily business operations. To illustrate them as completely as possible, the examples include the names of individuals, companies, brands, and products. All of these names are ctitious and any similarity to actual people or business enterprises is entirely coincidental.

Page 30

If you are viewing this information in softcopy, the photographs and color illustrations may not appear.

The drawings and specications contained herein shall not be reproduced in whole or in part without the written permission of IBM.

IBM has prepared this information for use with the specic machines indicated. IBM makes no representations that it is suitable for any other purpose.

IBM's computer systems contain mechanisms designed to reduce the possibility of undetected data corruption or loss. This risk, however, cannot be eliminated. Users who experience unplanned outages, system failures, power fluctuations or outages, or component failures must verify the accuracy of operations performed and data saved or transmitted by the system at or near the time of the outage or failure. In addition, users must establish procedures to ensure that there is independent data verication before relying on such data in sensitive or critical operations. Users should periodically check IBM's support websites for updated information and xes applicable to the system and related software.

Homologation statement

This product may not be certied in your country for connection by any means whatsoever to interfaces of public telecommunications networks. Further certication may be required by law prior to making any such connection. Contact an IBM representative or reseller for any questions.

Accessibility features for IBM Power Systems servers

Accessibility features assist users who have a disability, such as restricted mobility or limited vision, to use information technology content successfully.

Overview

The IBM Power Systems servers include the following major accessibility features:

• Keyboard-only operation

• Operations that use a screen reader

The IBM Power Systems servers use the latest W3C Standard, WAI-ARIA 1.0 (www.w3.org/TR/wai-aria/), to ensure compliance with US Section 508 (www.access-board.gov/guidelines-and-standards/ communications-and-it/about-the-section-508-standards/section-508-standards) and Web Content Accessibility Guidelines (WCAG) 2.0 (www.w3.org/TR/WCAG20/). To take advantage of accessibility features, use the latest release of your screen reader and the latest web browser that is supported by the IBM Power Systems servers.

The IBM Power Systems servers online product documentation in IBM Knowledge Center is enabled for accessibility. The accessibility features of IBM Knowledge Center are described in the Accessibility section of the IBM Knowledge Center help (www.ibm.com/support/knowledgecenter/doc/ kc_help.html#accessibility).

Keyboard navigation

This product uses standard navigation keys.

Interface information

The IBM Power Systems servers user interfaces do not have content that flashes 2 - 55 times per second.

The IBM Power Systems servers web user interface relies on cascading style sheets to render content properly and to provide a usable experience. The application provides an equivalent way for low-vision users to use system display settings, including high-contrast mode. You can control font size by using the device or web browser settings.

The IBM Power Systems servers web user interface includes WAI-ARIA navigational landmarks that you can use to quickly navigate to functional areas in the application.

Power Systems: Vital product data card for the 9040-MR9

Page 31

Vendor software

The IBM Power Systems servers include certain vendor software that is not covered under the IBM license agreement. IBM makes no representation about the accessibility features of these products. Contact the vendor for accessibility information about its products.

Related accessibility information

In addition to standard IBM help desk and support websites, IBM has a TTY telephone service for use by deaf or hard of hearing customers to access sales and support services:

TTY service 800-IBM-3383 (800-426-3383) (within North America)

For more information about the commitment that IBM has to accessibility, see IBM Accessibility (www.ibm.com/able).

IBM Software products, including software as a service solutions, (“Software Offerings”) may use cookies or other technologies to collect product usage information, to help improve the end user experience, to tailor interactions with the end user, or for other purposes. In many cases no personally identiable information is collected by the Software Offerings. Some of our Software Offerings can help enable you to collect personally identiable information. If this Software Offering uses cookies to collect personally identiable information, specic information about this offering’s use of cookies is set forth below.

This Software Offering does not use cookies or other technologies to collect personally identiable information.

If the congurations deployed for this Software Offering provide you as the customer the ability to collect personally identiable information from end users via cookies and other technologies, you should seek your own legal advice about any laws applicable to such data collection, including any requirements for notice and consent.

For more information about the use of various technologies, including cookies, for these purposes, see IBM’s Privacy Policy at http://www.ibm.com/privacy www.ibm.com/privacy/details the section entitled “Cookies, Web Beacons and Other Technologies” and the “IBM Software Products and Software-as-a-Service Privacy Statement” at http://www.ibm.com/ software/info/product-privacy.

Trademarks

IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business Machines Corp., registered in many jurisdictions worldwide. Other product and service names might be trademarks of IBM or other companies. A current list of IBM trademarks is available on the web at Copyright and trademark information at www.ibm.com/legal/copytrade.shtml.

Linux is a registered trademark of Linus Torvalds in the United States, other countries, or both.

Electronic emission notices

and IBM’s Online Privacy Statement at http://

When attaching a monitor to the equipment, you must use the designated monitor cable and any interference suppression devices supplied with the monitor.

Notices

Page 32

Class A Notices

The following Class A statements apply to the IBM servers that contain the POWER9 processor and its features unless designated as electromagnetic compatibility (EMC) Class B in the feature information.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modications to this equipment. Unauthorized changes or modications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada Compliance Statement

CAN ICES-3 (A)/NMB-3(A)

European Community Compliance Statement

This product is in conformity with the protection requirements of EU Council Directive 2014/30/EU on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a nonrecommended modication of the product, including the tting of non-IBM option cards.

European Community contact: IBM Deutschland GmbH Technical Regulations, Abteilung M456 IBM-Allee 1, 71139 Ehningen, Germany Tel: +49 800 225 5426 email: halloibm@de.ibm.com

Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

VCCI Statement - Japan

The following is a summary of the VCCI Japanese statement in the box above:

This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a domestic environment, radio interference may occur, in which case, the user may be required to take corrective actions.

Power Systems: Vital product data card for the 9040-MR9

Page 33

Japan Electronics and Information Technology Industries Association Statement

This statement explains the Japan JIS C 61000-3-2 product wattage compliance.

This statement explains the Japan Electronics and Information Technology Industries Association (JEITA) statement for products less than or equal to 20 A per phase.

This statement explains the JEITA statement for products greater than 20 A, single phase.

This statement explains the JEITA statement for products greater than 20 A per phase, three-phase.

Electromagnetic Interference (EMI) Statement - People's Republic of China

Declaration: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may need to perform practical action.

Electromagnetic Interference (EMI) Statement - Taiwan

The following is a summary of the EMI Taiwan statement above.

Notices

Page 34

Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user will be required to take adequate measures.

IBM Taiwan Contact Information:

Electromagnetic Interference (EMI) Statement - Korea

Germany Compliance Statement

Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse A EU-Richtlinie zur Elektromagnetischen Verträglichkeit

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2014/30/EU zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaatenund hält die Grenzwerte der EN 55022 / EN 55032 Klasse A ein.

Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der IBM empfohlene Kabel angeschlossen werden. IBM übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung von IBM verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne Empfehlung von IBM gesteckt/eingebaut werden.

EN 55022 / EN 55032 Klasse A Geräte müssen mit folgendem Warnhinweis versehen werden: "Warnung: Dieses ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich FunkStörungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Maßnahmen zu ergreifen und dafür aufzukommen."

Deutschland: Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Geräten

Dieses Produkt entspricht dem “Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG)“. Dies ist die Umsetzung der EU-Richtlinie 2014/30/EU in der Bundesrepublik Deutschland.

Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG) (bzw. der EMC Richtlinie 2014/30/EU) für Geräte der Klasse A

Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen CE - zu führen.

Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller: International Business Machines Corp. New Orchard Road Armonk, New York 10504 Tel: 914-499-1900

Der verantwortliche Ansprechpartner des Herstellers in der EU ist: IBM Deutschland GmbH Technical Relations Europe, Abteilung M456 IBM-Allee 1, 71139 Ehningen, Germany Tel: +49 (0) 800 225 5426 email: HalloIBM@de.ibm.com

Generelle Informationen:

Power Systems: Vital product data card for the 9040-MR9

Page 35

Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 / EN 55032 Klasse A.

Electromagnetic Interference (EMI) Statement - Russia

Class B Notices

The following Class B statements apply to features designated as electromagnetic compatibility (EMC) Class B in the feature installation information.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult an IBM-authorized dealer or service representative for help.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM-authorized dealers. IBM is not responsible for any radio or television interference caused by unauthorized changes or modications to this equipment. Unauthorized changes or modications could void the user's authority to operate this equipment.

Industry Canada Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

European Community Compliance Statement

European Community contact: IBM Deutschland GmbH Technical Regulations, Abteilung M456 IBM-Allee 1, 71139 Ehningen, Germany

Notices

Page 36

Tel: +49 800 225 5426 email: halloibm@de.ibm.com

VCCI Statement - Japan

Japan Electronics and Information Technology Industries Association Statement

This statement explains the Japan JIS C 61000-3-2 product wattage compliance.

This statement explains the Japan Electronics and Information Technology Industries Association (JEITA) statement for products less than or equal to 20 A per phase.

This statement explains the JEITA statement for products greater than 20 A, single phase.

This statement explains the JEITA statement for products greater than 20 A per phase, three-phase.

Power Systems: Vital product data card for the 9040-MR9

Page 37

IBM Taiwan Contact Information

Germany Compliance Statement

Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse B EU-Richtlinie zur Elektromagnetischen Verträglichkeit

Deutschland: Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Geräten

Dieses Produkt entspricht dem “Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG)“. Dies ist die Umsetzung der EU-Richtlinie 2014/30/EU in der Bundesrepublik Deutschland.

Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG) (bzw. der EMC Richtlinie 2014/30/EU) für Geräte der Klasse B

Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen CE - zu führen.

Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller: International Business Machines Corp. New Orchard Road Armonk, New York 10504 Tel: 914-499-1900

Generelle Informationen:

Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022/ EN 55032 Klasse B.

Terms and conditions

Permissions for the use of these publications are granted subject to the following terms and conditions.

Applicability: These terms and conditions are in addition to any terms of use for the IBM website.

Personal Use: You may reproduce these publications for your personal, noncommercial use provided that

all proprietary notices are preserved. You may not distribute, display or make derivative works of these publications, or any portion thereof, without the express consent of IBM.

Notices

Page 38

Commercial Use: You may reproduce, distribute and display these publications solely within your

enterprise provided that all proprietary notices are preserved. You may not make derivative works of these publications, or reproduce, distribute or display these publications or any portion thereof outside your enterprise, without the express consent of IBM.

Rights: Except as expressly granted in this permission, no other permissions, licenses or rights are granted, either express or implied, to the publications or any information, data, software or other intellectual property contained therein.

IBM reserves the right to withdraw the permissions granted herein whenever, in its discretion, the use of the publications is detrimental to its interest or, as determined by IBM, the above instructions are not being properly followed.

You may not download, export or re-export this information except in full compliance with all applicable laws and regulations, including all United States export laws and regulations.

IBM MAKES NO GUARANTEE ABOUT THE CONTENT OF THESE PUBLICATIONS. THE PUBLICATIONS ARE PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE.

24 Power Systems: Vital product data card for the 9040-MR9

Page 39

Page 40

IBM®