IBASE Technology SI-60E User Manual

SI-60E User Manual

SI-60E

User Manual

ii

SI-60E User Manual

Revision

Release Date

V1.0

2015/04/28

iii

IBASE Technology Inc.

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of IBASE Technology INC. (“IBASE ”).

Products and corporate names mentioned in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used for identification purposes only. All trademarks are the property of their respective owners.

Every effort has been made to ensure that the contents of this manual are correct and up to date. However, the manufacturer makes no guarantee regarding the accuracy of its contents, and reserves the right to make changes without prior notice.

iv

SI-60E User Manual

Table of Contents

Setting up your system .......................................................................................................... v

Care during use ..................................................................................................................... vi

Acknowledgments ................................................................................................................ vii

CHAPTER 1 INTRODUCTION .................................................................................... 1

1.1 General Description.......................................................................................................... 1

1.2 System Specifications...................................................................................................... 2

1.2.1 Hardware Specifications ............................................................................................... 2

1.2.2 Dimensions .................................................................................................................... 3

1.2.3 I/O View ........................................................................................................................... 4

1.3 Exploded View of the SI-60E Assembly .......................................................................... 5

1.3.1 Parts Description ........................................................................................................... 6

1.4 Packing List ...................................................................................................................... 7

1.4.1 Optional Items module .................................................................................................. 7

1.5 HARDWARE INSTALLATION ............................................................................................ 8

1.5.1 Mounting Installation ..................................................................................................... 8

1.5.2 Installing the storage ..................................................................................................... 9

CHAPTER 2 MOTHERBOARD INTRODUCTION .........................................................10

2.1 Introduction..................................................................................................................... 10

2.2 Installations ..................................................................................................................... 12

2.2.1 Installing the Memory .................................................................................................. 12

2.3 Setting the Jumpers ....................................................................................................... 13

2.4 Connectors on MBD60E ................................................................ ................................. 15

CHAPTER 3 BIOS SETUP .........................................................................................21

3.1 BIOS Introduction ........................................................................................................... 21

3.2 BIOS Setup ................................ ...................................................................................... 21

CHAPTER 4 DRIVERS INSTALLATION .......................................................................45

4.1 Intel Chipset Software Installation Utility...................................................................... 45

4.2 AMD Radeon E8860 Graphics Driver ............................................................................ 48

4.3 Realtek High Definition Audio Driver ............................................................................ 52

4.4 Intel® I21x Gigabit Network Driver ................................................................................ 54

4.5 Intel® Management Engine(ME) Driver ......................................................................... 58

4.6 Intel® USB 3.0 eXtensible Host Controller Driver ........................................................ 61

4.7 Realtek RTL8111G LAN Driver ....................................................................................... 64

4.8 IDD100 Driver and Utility ................................................................................................ 66

Appendix ...............................................................................................................71

A. IBASE Display Matrix User Manual................................................................................. 71

B. I/O Port Address Map ................................ ....................................................................... 71

C. Interrupt Request Lines (IRQ) ......................................................................................... 75

D. Watchdog Timer Configuration ....................................................................................... 76

v

IBASE Technology Inc.

Safety Information

Your SI-60E is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions

Setting up your system

 Read and follow all instructions in the documentation before you operate your

system.

 Do not use this product near water.  Set up the system on a stable surface. Do not secure the system on any unstable

plane.

 Do not place this product on an unstable cart, stand, or table. The product may

fall, causing serious damage to the product.

 Slots and openings on the chassis are for ventilation. Do not block or cover these

openings. Make sure you leave plenty of space around the system for ventilation. Never insert objects of any kind into the ventilation openings.

 This system should be operated from the type of power indicated on the marking

label. If you are not sure of the type of power available, consult your dealer or local power company.

 Use this product in environments with ambient temperatures between -40˚C and

75˚C.

 If you use an extension cord, make sure that the total ampere rating of the

devices plugged into the extension cord does not exceed its ampere rating.

 DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE

STORAGE TEMPERATURE MAY GO BELOW -50° C (-58° F) OR ABOVE 85° C (185° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

vi

SI-60E User Manual

Care during use

 Do not walk on the power cord or allow anything to rest on it.  Do not spill water or any other liquids on your system.  When the system is turned off, a small amount of electrical current still flows.

Always unplug all power, and network cables from the power outlets before cleaning the system.

 If you encounter the following technical problems with the product, unplug the

power cord and contact a qualified service technician or your retailer.

 The power cord or plug is damaged.  Liquid has been spilled into the system.  The system does not function properly even if you follow the operating

instructions.

 The system was dropped or the cabinet is damaged.

Lithium-Ion Battery Warning

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

NO DISASSEMBLY

The warranty does not apply to the products that have been disassembled by users

WARNING

HAZARDOUS MOVING PARTS

KEEP FINGERS AND OTHER BODY PARTS AWAY

vii

IBASE Technology Inc.

Acknowledgments

 AMI is a registered trademark of AMI Software International, Inc.  AMD and ATI are registered trademarks of AMD Corporation.  Intel, Pentium, and Intel Core are registered trademarks or trademarks of

Intel Corporation.

 Microsoft Windows is a registered trademark of Microsoft Corporation.  FINTEK is a registered trademark of FINTEK Electronics Corporation.  REALTEK is a registered trademark of REALTEK Electronics Corporation.  All other product names or trademarks are properties of their respective

owners.

1

SI-60E User Manual

CHAPTER 1 INTRODUCTION

1.1 General Description

The “Signature Book™” SI-60E is a professional digital signage system powered by 4th Gen. Intel® CoreTM I Desktop Processors with AMD Radeon™ E8860 graphics. The SI-60E integrates 12 HDMI ports with EDID emulation function and one DVI-I for console. Additionally, SI-60E has two quad-channel DDR3L-1600 sockets to provide up to 32GB of memory. It also has dual Gigabit Ethernet, dual extended SSD drive, Intel AMT for remote control and IBASE’s iSMART green technology for power on/off scheduling and power resume functions. The ruggedized design player’s chassis that provides passive cooling for better system reliability and quiet operation.

SI-60E overview

2

SI-60E User Manual

1.2 System Specifications

1.2.1 Hardware Specifications

Model Name

SI-60E

System Mainboard

MBD60E

CPU

4th Generation Intel® Core™ i7/i5/i3 and Pentium® QC/DC processors; Up to 3.5GHz

Memory

4x DDR3 1600 MHz, Max. 32GB

I/O Interface

12x HDMI with EDID emulation function 1x DVI-I for console 4x USB 3.0 ports 2x RJ45 for LAN 1x RJ45 for RS232 3x Microjack audio connectors for Line-in / Line-out/MIC-in Power LED for power on/off & HDD 1x power button

1x AC power inlet

Storage

1x mSATA 2x SATA 3.0 2.5” HDD Dock (support Raid 1)

Expansion Slots

Dual mPCI-E(x1) slots for WiFi, 3G/LTE, capture card and TV tuner options

Construction

SGCC

Mounting

Standard system bracket

Dimensions

412mm(W) x 310mm(D) x 47mm(H)

16.22”(W) x 12.2”(D) x 1.85”(H)

Operating Temperature

0°C~ 45°C (32°F~113°F)

Storage Temperature

-20°C ~ 80°C (-4°F~176°F) Relative Humidity

5~90% @ 45°C, (non-condensing)

Vibration

mSATA: 5 grms / 5~500Hz / random operation

RoHS

Available

Certification

CE, FCC, CCC, UL

‧

This specification is subject to change without prior notice.

3

IBASE Technology Inc.

1.2.2 Dimensions

4

SI-60E User Manual

1.2.3 I/O View

SI-60E front side

SI-60E rear side

5

IBASE Technology Inc.

1.3 Exploded View of the SI-60E Assembly

6

SI-60E User Manual

1.3.1 Parts Description

Part No.

Description

Part No.

Description

1

SI-60E_BASE

2

4028_fan

3

HDMI Board Module

4

Power module

5

SI-60E Main Board

6

SI-60E_HDD-TRAY

7

SI-60E_HDD-BRK

8

Screw F Type M3*0.5

9

SATA Cable

10

2.5" SATA HDD

11

M3 nut

12

M3 double screw bolt

13

SI-60E_top-cover_L

14

SI-60E_top-cover_r

15

Screw PW Type M3*0.5

16

M3 screw

17

Screw F Type M3*0.5 BK

7

IBASE Technology Inc.

1.4 Packing List

Item No.

Description

Qty

1

Driver CD

1 2 Power adaptor

1

3

Power cord

1

1.4.1 Optional Items module

WiFi Solution

Description

WiFi module

Wireless; PCI-E Mini Card 802.11B/G/N [AW-NE238H] (A008WLAWNE238H000P)

External Antenna 2pcs

WiFi Antenna (A055RFA02C2M20800P)

Internal cable 1pcs

Internal Antenna 300mm [BTC130-1-70B-300] RoHS (A055RFA0000020100P)

Internal cable 1pcs

Internal Antenna 200mm [BTC130-1-70B-200-1] RoHS (A055RFA0000020000P)

Screw, 2pcs

Screw; A44-N NI 3.4 NYLOK M2*L3.8 P0.4mm [LHS] RoHS (H02203A0442200N00P)

Bracket, -1set

Component BOM; MPCIE-EXT V-B2 Bracket (SC2MPCIEEXT0B2100P)

3G Solution

Description

3G

Wireless; 3.75G UMTS/HSPA [ZU202] RoHS (A008WIRELESS00520P)

3G+GPS

Wireless; 3.75G UMTS/HSPA & GPS Module [ZU200] RoHS (A008WIRELESS00510P)

WW-350U

Wireless; 3.75G UMTS/HSPA [NAVISYS WW-350U] RoHS (A008WIRELESS00530P)

Cable

Cable; SMA IPX Cable For 3G 30CM [RF11030A] RoHS (A012INTENAL010000P)

Antenna

3G [ANT0921Q2P] RoHS (A055ANT0921Q2P000P)

COM Port Cable

Description

EXT-311

Cable; EXT-311 2-HD 10C 150CM; DSUB-9F => RJ45-10M RoHS (C501EXT3110A12000P)

EXT-312

Cable; EXT-312 2-HD 10C 150CM; DSUB-9M => RJ45-10M RoHS (C501EXT3120A12000P)

8

SI-60E User Manual

1.5 HARDWARE INSTALLATION

1.5.1 Mounting Installation

1. Please install SI-60E to the intended location using 4x M4*0.7*6L screws, as shown in the picture.

9

IBASE Technology Inc.

1.5.2 Installing the storage

1. Remove the two screws on the HDD cover and draw the HDD out.

2. Install the HDD/SSD to the HDD bracket with 4 screws.

10

SI-60E User Manual

CHAPTER 2 MOTHERBOARD INTRODUCTION

2.1 Introduction

MBD60E Jumpers and Connectors

11

IBASE Technology Inc.

IMBD60E Board Dimensions

12

SI-60E User Manual

2.2 Installations

2.2.1 Installing the Memory

The MBD60E board supports four DDR3 memory modules for a maximum total of 32GB in DDR3 SODIMM memory type.

Installing and Removing Memory Modules

To install the DDR3 modules, locate the memory slot on the board and perform the following steps:

1. Hold the DDR3 module so that the key of the DDR3 module aligned with that on the

memory slot.

2. Gently push the DDR3 module in an upright position until the clips of the slot close

to hold the DDR3 module in place when the DDR3 module touches the bottom of the slot.

3. To remove the DDR3 module, press the clips with both hands.

13

IBASE Technology Inc.

2.3 Setting the Jumpers

Jumpers are used on MBD60E to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the jumpers and connectors on MBD60E and their respective functions.

JBAT1: Clear CMOS Contents

JBAT1

Setting

Function

Pin 1-2

Short/Closed

Normal

Pin 2-3

Short/Closed

Clear CMOS

JP1: COM2 RS232 RI/+5V/+12V Power Setting

JP1

Setting

Function

Pin 1-3

Short/Closed

+12V

Pin 3-4

Short/Closed

RI

Pin 5-3

Short/Closed

+5V

1

3

1 2

5 6

14

SI-60E User Manual

JP2: COM1 RS232 RI/+5V/+12V Power Setting

JP2

Setting

Function

Pin 1-3

Short/Closed

+12V

Pin 3-4

Short/Closed

RI

Pin 5-3

Short/Closed

+5V

JP3: Flash Descriptor Security Override (Factory use only)

2 1

1 2

5 6

15

IBASE Technology Inc.

2.4 Connectors on MBD60E

J1: COM2 Connector [HRS DF11-10DP-2DSA(08)]

Signal Name

Pin #

Signal Name

Data carrier detect

1

2

Receive data

Transmit data

3

4

Data terminal ready

Ground

5

6

Data set ready

Request to send

7

8

Clear to send

Ring indicator

9

10

Not Used

J2: ATX +12V Jack [HAOGUO ATX4PT-NY46]

Pin #

Signal Name

1

Ground

2

Ground

3

DC_IN

4

DC_IN

J3: For SPI Debug tools Pin Header

1 9

2 10

3 1

4 2

1 2

9 10

16

SI-60E User Manual

J4, J5, J6, J7 DDR III Socket

J8: MCU Flash Connector (factory use only)

J9: Debug Port Connector (Factory use only)

J10: Reset Pin Header

J11: Mini PCIe Slot (Full size with SIM Card)

1

4

10 9

2 1

2

1

17

IBASE Technology Inc.

J12: Mini PCIe Slot (Full size with mSATA)

J13: ATX Power Supply Connector

Signal Name

Pin #

Signal Name

3.3V

13 1 3.3V

-12V

14 2 3.3V

Ground

15 3 Ground

PS-ON

16 4 +5V

Ground

17 5 Ground

Ground

18 6 +5V

Ground

19 7 Ground

-5V

20 8 Power good

+5V

21 9 5VSB

+5V

22

10

+12V

+5V

23

11

+12V

Ground

24

12

+3.3V

J14: SIM Card Slot

12 24

1 13

18

SI-60E User Manual

CN1: COM1 / DVI-I Connector

CN2: Audio Jack

CN3: RTL8111G-CG /USB3.0 Connector

CN4: I218LM / USB3.0 Connector

CN5/6:SATA 3 Connector

19

IBASE Technology Inc.

CPU_FAN1: CPU Fan Power Connector

Pin #

Signal Name

1

Ground

2

+12V

3

Rotation detection

4

Control

GPU_FAN1: GPU Fan Power Connector

Pin #

Signal Name

1

Ground

2

+12V

3

Rotation detection

4

Control

SYS_FAN1: System Fan1 Power Connector

Pin #

Signal Name

1

Ground

2

+12V

3

Rotation detection

1 4

1

3

1 4

20

SI-60E User Manual

SW1: Power On Button

LED1: PWR (Green)/ HDD LED (Red)

PCIE1, PCIE2, PCIE3: DP Signal from AMD E8860 to IDD100

21

IBASE Technology Inc.

CHAPTER 3 BIOS SETUP

This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows:

3.1 BIOS Introduction

The BIOS (Basic Input/Output System) installed in your computer system’s ROM

supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.

3.2 BIOS Setup

The BIOS provides a Setup utility program for specifying the system configurations and settings. The BIOS ROM of the system stores the Setup utility. When you turn on the computer, the BIOS is immediately activated. Pressing the <Del> key immediately allows you to enter the Setup utility. If you are a little bit late pressing the <Del> key, POST (Power On Self Test) will continue with its test routines, thus preventing you from invoking the Setup. If you still wish to enter Setup, restart the system by pressing the ”Reset” button or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the system Off and back On again. The following message will appear on the screen:

Press <DEL> to Enter Setup

In general, you press the arrow keys to highlight items, <Enter> to select, the <PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit.

When you enter the Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices.

Warning:

It is strongly recommended that you avoid making any changes to the chipset defaults. These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could cause the system to become unstable and crash in some cases.

22

SI-60E User Manual

Main Settings

Main Advanced Chipset Boot Security Save & Exit

System Language

[English]

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit

ESC: Exit

System Date System Time

[Tue 01/20/2009]

[21:52:06]

Access Level

Administrator

System Language

Choose the system default language.

System Date

Set the Date. Use Tab to switch between Data elements.

System Time

Set the Time. Use Tab to switch between Data elements.

23

IBASE Technology Inc.

Advanced Settings

This section allows you to configure and improve your system and allows you to set up some system features according to your preference.

Main Advanced Chipset Boot Security Save & Exit

► ACPI Settings ► Trusted Computing

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit

ESC: Exit

► Wake up event setting

► CPU Configuration

► SATA Configuration

►Shutdown Temperature Configuration

► iSmart Controller 3.1

► AMT Configuration

► USB Configuration

► F81846 Super IO Configuration

► F81846 H/W Monitor

24

SI-60E User Manual

ACPI Settings

Main Advanced Chipset Boot Security Save & Exit

ACPI Settings

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit

ESC: Exit

ACPI Sleep State

S3 only (Suspend to …)

Lock Legacy Resources S3 Video Repost

Disabled Disabled

ACPI Sleep State

Select ACPI sleep state the system will enter when the SUSPEND button is pressed.

Lock Legacy Resources

Enables or Disables Lock of Legacy Resources

S3 Video Repost

Enable or Disable S3 Video Repost

25

IBASE Technology Inc.

Trusted Computing

Main Advanced Chipset Boot Security Save & Exit

Configuration

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit

ESC: Exit

Security Device Support

Disabled

Current Status Information

SUPPORT TURNED OFF

Security Device Support

Enables or disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.

TPM State

Enable/Disable Security Device. NOTE: Your Computer will reboot during restart in order to change State of the Device.

Pending operation

Schedule an Operation for the Security Device. NOTE: Your Computer will reboot during restart in order to change State of Security Device.

26

SI-60E User Manual

Wake up event settings

Main Advanced Chipset Boot Security Save & Exit

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

ESC: Exit

Wake on PCIE Wake Event

Disabled

Wake on PCIE Wake Event

The options are Disabled and Enabled.

27

IBASE Technology Inc.

CPU Configuration

This section shows the CPU configuration parameters.

Main Advanced Chipset Boot Security Save & Exit

CPU Configuration Intel(R) Core(TM) i7-4770S CPU @ 3.10GHz

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

CPU Signature

306c3

Processor Family

6

Microcode Patch

17

FSB Speed

100 MHz

Max CPU Speed

3100 MHz

Min CPU Speed

800 MHz

CPU Speed

3500 MHz

Processor Cores

4

Intel HT Technology

Supported

Intel VT-x Technology

Supported

Intel SMX Technology

Supported

64-bit

Supported

EIST Technology

Supported

Hyper-threading

Enabled

Active Processor Cores Overclocking lock

All Disabled

Limit CPUID Maximum

Disabled

Execute Disable Bit

Disabled

Intel Virtualization Technology Hardware Prefetcher

Disabled Disabled

Adjacent Cache Line Prefetch

Disabled

EIST

Enabled

Turbo Mode

Enabled

28

SI-60E User Manual

Hyper-threading

Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled.

Active Processor Cores

Number of cores to enable in each processor package.

Overclocking lock

FLEX_RATIO(194) MSR

Limit CPUID Maximum

Disabled for Windows XP

Execute Disable Bit

XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3.)

Intel Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology

Hardware Prefetcher

Enable the Mid Level Cache (L2) streamer prefetcher.

Adjacent Cache Line Prefetch

Enable the Mid Level Cache (L2) prefetching of adjacent cache lines.

EIST

Enable/Disable Intel Speedstep

Turbo Mode

Turbo Mode.

29

IBASE Technology Inc.

SATA Configuration

Main Advanced Chipset Boot Security Save & Exit

SATA Controller(s)

Enabled

SATA Mode Selection

AHCI

SATA Controller Speed

Default

Serial ATA Port 0

Empty

Software Preserve

Unknown

Port 0

Enabled

Hot Plug

Disabled

Serial ATA Port 1

Empty

Software Preserve

Unknown

Port 1

Enabled

Hot Plug

Disabled

Serial ATA Port 2

Software Preserve Port 2 Hot Plug

Serial ATA Port 3

Software Preserve Port 3

Hot Plug

Serial ATA Port 4

Software Preserve Port 4 Hot Plug

Serial ATA Port 5

Software Preserve Port 5 Hot Plug

Empty Unknown Enabled Disabled

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit

ESC: Exit

SATA Controller(s)

Enable or disable SATA Device.

SATA Mode Selection

Determines how SATA controller(s) operate. (1) IDE Mode. (2) AHCI Mode. (3) RAID Mode.

SATA Controller Speed

Indicates the maximum speed the SATA controller can support.

Port 0

Enable or Disable SATA Port

Hot Plug

Designates this port as Hot Pluggable.

30

SI-60E User Manual

Shutdown Temperature Configuration

Main Advanced Chipset Boot Security Save & Exit

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

APCI Shutdown Temperature

Disabled

ACPI Shutdown Temperature

The default setting is Disabled.

iSmart Controller 3.1

Main Advanced Chipset Boot Security Save & Exit

iSmart Controller 3.1

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit

ESC: Exit

Power-On after Power failure PWR Resume Delay PWR Resume Delay Value(Seconds) Temperature Guardian

Enable Enable 5 Disable

Schedule Slot 1

None

Schedule Slot 2

None

Power-On after Power failure

This field sets the system power status whether Disable or Enable when power returns to the system from a power failure situation.

Temperature Guardian

Generate the reset signal when system hangs up on POST.

Schedule Slot 1 / 2

Setup the hour/minute for system power on.

31

IBASE Technology Inc.

AMT Configuration

Main Advanced Chipset Boot Security Save & Exit

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Intel AMT

Enabled

BIOS Hotkey Pressed

Disabled

MEBx Selection Screen

Disabled

Hide Un-Configure ME Confirmation

Disabled

Un-Configure ME

Disabled

Amt Wait Timer

0

Activate Remote Assistance Process

Disabled

USB Configure

Enabled

PET Progress

Enabled

AMT CIRA Timeout

0

Watchdog

Disabled

OS Timer

0

BIOS Timer

0

Intel AMT

Enable/Disable Intel (R) Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device.

BIOS Hotkey Pressed

OEMFLag Bit 1: Enable/Disable BIOS hotkey press.

AMT Configuration

OEMFLag Bit 2: Enable/Disable MEBx selection screen.

Hide Un-Configure ME Configuration

OEMFlag Bit 6: Hide Un-Configure ME without password Confirmation Prompt

Un-Configure ME

OEMFlag Bit 15: Un-Configure ME without password.

32

SI-60E User Manual

Amt Wait Timer

Set timer to wait before sending ASF_GET_BOOT_OPTIONS.

Activate Remote Assistance Process

Trigger CIRA boot.

USB Configure

Enable/Disable USB Configure function.

PET Progress

User can Enable/Disable PET Events progress to receive PET events or not.

Watchdog Timer

Enable/Disable Watchdog Timer.

USB Configuration

Main Advanced Chipset Boot Security Save & Exit

USB Configuration

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

USB Module Version

8.10.28

USB Devices:

Legacy USB Support

Enabled

USB3.0 Support

Enabled

XHCI Hand-off

Enabled

EHCI Hand-off

Enabled

USB Mass Storage Driver Support

Enabled

USB hardware delays and time-outs:

USB Transfer time-out

20 sec

Device reset tine-out

20 sec

Device power-up delay

Auto

33

IBASE Technology Inc.

Legacy USB Support

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

USB3.0 Support

Enable/Disable USB3.0 (XHCI) Controller support.

XHCI Hand-off

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.

EHCI Hand-off

This is a workaround for OSes without EHCI hand-off support. The XHCI ownership change should be claimed by EHCI driver.

USB Mass Storage Driver Support

Enable/Disable USB Mass Storage Driver Support.

USB Transfer time-out

The time-out value for Control, Bulk, and Interrupt transfers.

Device reset tine-out

USB mass Storage device start Unit command time-out.

Device power-up delay

Maximum time the device will take before it properly reports itself to the Host Controller. ‘Auto’ uses default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor.

34

SI-60E User Manual

F81846 Super IO Configuration

Main Advanced Chipset Boot Security Save & Exit

F81846 Super IO Configuration

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

F81846 Super IO Chip

F81846

► Serial Port 0 Configuration

► Serial Port 1 Configuration

Serial Port Configuration

Set Parameters of Serial Ports. User can Enable/Disable the serial port and Select an optimal settings for the Super IO Device.

35

IBASE Technology Inc.

F81846 H/W Monitor

Main Advanced Chipset Boot Security Save & Exit

PC Health Status

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

CPU temperature

+34 C

SYS temperature

+29 C

FAN1 Speed

2170 RPM

FAN2 Speed

2170 RPM

FAN3 Speed

2170 RPM

+5V

+5.087 V

+12V

+12.056 V

Fan 1 smart fan control Fan 1 smart fan control Fan 1 smart fan control

50 C 50 C 50 C

Temperatures/Voltages

These fields are the parameters of the hardware monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status.

Smart SYS_FAN1/CPU_FAN1 Function

This field enables or disables the smart fan feature. Disabled (default) 50 ℃ 60 ℃ 70 ℃

80 ℃

36

SI-60E User Manual

Chipset Settings

This section allows you to configure and improve your system and allows you to set up some system features according to your preference.

Main Advanced Chipset Boot Security Save & Exit

► PCH-IO Configuration

► System Agent (SA) Configuration

PCH-IO Configuration

This section allows you to configure the North Bridge Chipset.

Main Advanced Chipset Boot Security Save & Exit

Intel PCH RC Version

1.8.0.0

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Intel PCH SKU Name

Q87

Intel PCH Rev ID

05/C2

► PCI Express Configuration

► USB Configuration

► PCH Azalia Configuration

PCH LAN Controller Wake on LAN

Enabled Enabled

PCH LAN Controller

Enable or disable onboard NIC.

Wake on LAN

Enable or disable integrated LAN to wake the system. (The Wake On LAN cannot be disabled if ME is on at Sx state.)

37

IBASE Technology Inc.

PCI Express Configuration

Main Advanced Chipset Boot Security Save & Exit

PCI Express Configuration

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

DMI Link ASPM Control

Enabled

DMI Link Extended Synch Control

Disabled

PCIe-USB Glitch W/A

Disabled

Subtractive Decode

Disabled

► PCI Express Root Port 1

► PCI Express Root Port 2

► PCI Express Root Port 3

► PCI Express Root Port 4

► PCI Express Root Port 5

PCI-E Port 6 is assigned to LAN

► PCI Express Root Port 7

► PCI Express Root Port 8

DMI Link ASPM Control

The control of Active State Power Management on both NB side and SB side of the DMI Link.

DMI Link Extended Synch Control

The control of Extended Synch on SB side of the DMI Link.

PCIe-USB Glitch W/A

PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG port.

Subtractive Decode

Enable or disable PCI Express Subtractive Decode.

38

SI-60E User Manual

USB Configuration

Main Advanced Chipset Boot Security Save & Exit

USB Configuration

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

USB Precondition

Disabled

xHCI Mode

Auto

USB Ports Per-Port Disable Control

Disabled

USB Precondition

Precondition work on USB host controller and root ports for faster enumeration.

xHCI Mode

Mode of operation of xHCI controller.

USB Ports Per-Port Disable Control

Control each of the USB ports (0~13) disabling.

PCH Azalia Configuration

Main Advanced Chipset Boot Security Save & Exit

PCH Azalia Configuration

Azalia

Auto

Azalia

Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled. Enabled Azalia will be unconditionally Enabled. Auto = Azalia will be enabled if present, disabled otherwise.

39

IBASE Technology Inc.

System Agent (SA) Configuration

Main Advanced Chipset Boot Security Save & Exit

System Agent Bridge Name Haswell

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

System Agent RC Version

1.8.0.0

VT-d Capability

Supported

VT-d

Enabled

► Graphics Configuration ► Memory Configuration

VT-d

Check to enable VT-d function on MCH.

Graphics Configuration

Main Advanced Chipset Boot Security Save & Exit

Graphics Configuration

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Primary Display Primary PEG Primary PCIE

PEG Auto Auto

Internal Graphics

Disabled

40

SI-60E User Manual

Primary Display

Select which of IGFX/PEG/PCI graphics device should be Primary Display or select SG for switchable Gfx.

Primary PEG

Select PEG0/PEG1/PEG2/PEG3 Graphics device should be Primary PEG.

Primary PCIE

Select PCIE0/PCIE1/PCIE2/PCIE3/PCIE4/PCIE5/PCIE6PCIE7 Graphics device should be Primary PCIE.

Internal Graphics

Keep IGD enabled based on the setup options.

Memory Configuration

Aptio Setup Utility

Main Advanced Chipset Boot Security Save & Exit

Memory Information

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Memory RC Version

1.8.0.0

Memory Frequency

1600 MHz

Total Memory Memory Voltage

32768MB (DDR3)

1.50V

DIMM#0

8192 MB (DDR3)

DIMM#1

8192 MB (DDR3)

DIMM#2

8192 MB (DDR3)

DIMM#3

8192 MB (DDR3)

41

IBASE Technology Inc.

Boot Settings

This section allows you to configure the boot settings.

Main Advanced Chipset Boot Security Save & Exit

Boot Configuration

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Setup Prompt Timeout

1

Bootup NumLock State

On

Quiet Boot

Disabled

Fast Boot

Boot Mode select

Disabled

LEGACY

FIXED BOOT ORDER Priorities Boot Option #1

Hard Disk

Boot Option #2 Boot Option #3 Boot Option #4 Boot Option #5 Boot Option #6 Boot Option #7

CD/DVD USB Hard Disk USB CD/DVD USB Key USB Floppy Network

► CSM16 parameters CSM parameters

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.

Bootup NumLock State Select the keyboard NumLock state

Quiet Boot

Enables or disables Quiet Boot option

Fast Boot

Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options.

Boot Mode select

Select boot mode LEGACY/UEFI

42

SI-60E User Manual

FIXED BOOT ORDER Priorities

Sets the system boot order

CSM parameters

This section allows you to configure the boot settings.

Main Advanced Chipset Boot Security Save & Exit

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Launch CSM

Enabled

Boot option filter

UEFI and Legacy

Launch PXE OpROM policy

Do not launch

Launch Storage OpROM policy

Legacy only

Launch Video OpROM policy

Legacy only

Other PCI device ROM priority

Legacy OpROM

Launch CSM

This option controls if CSM will be launched

Boot option filter

This option controls what devices system can boot to

Launch PXE OpROM policy

Controls the execution of UEFI and Legacy PXE OpROM

Launch Storatge OpROM policy

Controls the execution of UEFI and Legacy Storage OpROM

Launch Video OpROM policy

Controls the execution of UEFI and Legacy Video OpROM

Other PCI device ROM priority

For PCI devices other than Network, Mass storage or Video defines which OpROM to launch

43

IBASE Technology Inc.

Security Settings

This section allows you to configure and improve your system and allows you to set up some system features according to your preference.

Main Advanced Chipset Boot Security Save & Exit

Password Description

→ ←Select Screen

↑↓Select Item Enter: Select +- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

If ONLY the Administrator’s password is set, then this only limit access to Setup and is only asked for when entering Setup.

If ONLY the User’s password is set, then this is a power on password and must be entered to boot

or enter Setup. In Setup the User will have Administrator rights.

The password length must be

in the following range:

Minimum length

3

Maximum length

20

Administrator Password

User Password

Administrator Password

Set Administrator Password

User Password

Set User Password

44

SI-60E User Manual

Save & Exit Settings

Main Advanced Chipset Boot Security Save & Exit

Save Changes and Exit

→ ←Select Screen

↑↓Select Item Enter: Select

+- Change Opt. F1:General Help F2:Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Discard Changes and Exit

Save Changes and Reset

Discard Changes and Reset

Save Options

Save Changes

Discard Changes

Restore Defaults

Save as User Defaults

Restore User Defaults

Save Changes and Exit

Exit system setup after saving the changes.

Discard Changes and Exit

Exit system setup without saving any changes.

Save Changes and Reset

Reset the system after saving the changes.

Discard Changes and Reset

Reset system setup without saving any changes.

Save Changes

Save Changes done so far to any of the setup options.

Discard Changes

Discard Changes done so far to any of the setup options.

Restore Defaults

Restore/Load Defaults values for all the setup options.

Save as User Defaults

Save the changes done so far as User Defaults.

Restore User Defaults

Restore the User Defaults to all the setup options.

45

IBASE Technology Inc.

CHAPTER 4 DRIVERS INSTALLATION

The Intel Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation.

IMPORTANT NOTE:

After installing your Windows operating system, you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation.

4.1 Intel Chipset Software Installation Utility

1. Insert the DVD that comes with the board. Click System and then SI-60E Series Products.

2. Click Intel(R) Chipset Software Installation Utility.

46

SI-60E User Manual

3. When the Welcome screen to the Intel® Chipset Device Software appears, click Next to continue.

4. Click Accept to accept the software license agreement and proceed with the installation process.

47

IBASE Technology Inc.

5. On the Readme File Information screen, click Install to continue the installation.

6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect.

48

SI-60E User Manual

4.2 AMD Radeon E8860 Graphics Driver

1. Insert the DVD that comes with the board. Click System and then SI -60E Series Products. Click AMD Radeon E8860 Graphics Driver.

2. When the Welcome screen appears, click Next to continue.

3. Select the language you would like to be displayed and click Next.

49

IBASE Technology Inc.

4. Click Install to continue the installation process.

50

SI-60E User Manual

5. Select Express and the installation location and click Next.

6. Click Accept to accept the End User License Agreement.

51

IBASE Technology Inc.

7. Setup complete. Click Finish to restart the computer and for changes to take effect.

8. To reboot the system, click Yes.

52

SI-60E User Manual

4.3 Realtek High Definition Audio Driver

1. Insert the DVD that comes with the board. Click System and then SI-60E Series Products.

2. Click Realtek High Definition Audio Driver.

53

IBASE Technology Inc.

3. On the Welcome to the InstallShield Wizard screen, click Yes to proceed with and complete the installation process.

4. The InstallShield Wizard Complete. Click Finish to restart the computer and for changes to take effect.

54

SI-60E User Manual

4.4 Intel® I21x Gigabit Network Driver

1. Insert the DVD that comes with the board. Click System and then SI-60E Series Products.

2. Click Intel® I21x Gigabit Network Driver.

55

IBASE Technology Inc.

3. When the Welcome screen appears, click Next.

4. Click Next to to agree with the license agreement.

56

SI-60E User Manual

5. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue.

6. The wizard is ready to begin installation. Click Install to begin the installation.

57

IBASE Technology Inc.

7. When InstallShield Wizard is complete, click Finish.

58

SI-60E User Manual

4.5 Intel® Management Engine(ME) Driver

Follow the steps below to install the Intel Management Engine.

1. Insert the DVD that comes with the board. Click System and then SI-60E Series Products.and then Intel® Management Engine(ME) Driver.

2. When the Welcome screen for Intel® Management Engine Components, click the checkbox for Install Intel® Control Center & click Next.

59

IBASE Technology Inc.

3. Click Yes to to agree with the license agreement.

4. When the Setup Progress screen appears, click Next. Then, click Finish when the setup progress has been successfully installed.

60

SI-60E User Manual

61

IBASE Technology Inc.

4.6 Intel® USB 3.0 eXtensible Host Controller Driver

1. Insert the DVD that comes with the board. Click System and then SI-60E Series Products. Click Intel® USB 3.0 eXtensible Host Controller Driver.

2. When the Welcome screen to the InstallShield Wizard for Intel® USB 3.0 eXtensible Host Controller Driver, click Next.

62

SI-60E User Manual

3. Click Yes to to agree with the license agreement and continue the installation.

4. On the Readme File Information screen, click Next to continue the installation of the Intel® USB 3.0 eXtensible Host Controller Driver.

63

IBASE Technology Inc.

5. Setup complete. Click Finish to restart the computer and for changes to take effect.

64

SI-60E User Manual

4.7 Realtek RTL8111G LAN Driver

1. Insert the DVD that comes with the board. Click System and then SI-60E Series Products. Click Realtek RTL8111G LAN Driver.

2. In the Welcome screen, click Next.

65

IBASE Technology Inc.

3. When the Ready to Install the Program screen appears, click Install to continue.

4. When InstallShield Wizard is complete, click Finish.

66

SI-60E User Manual

4.8 IDD100 Driver and Utility

1.Insert the DVD that comes with the board. Click System and then SI-60E Series Products. Click IDD100 Driver and Utility.

2. Click CP210x Installer

67

IBASE Technology Inc.

3. In the Welcome screen, click Next.

4. When the License Agreement the Program screen appears, click I accept this

agreement and Next.

68

SI-60E User Manual

5.When complete the Installation of the CP210x USB to UART Bridge Driver, click Finish.

6.Click SI-60E Installer.

69

IBASE Technology Inc.

7. In the Welcome screen, click Next.

8. When the Destination Folder screen appears, click Next.

70

SI-60E User Manual

9. When the Ready to Install the Program screen appears, click Install.

10.When InstallShield Wizard Complete, click Finish.

71

IBASE Technology Inc.

Appendix

A. IBASE Display Matrix User Manual

Software UART Control Application interface

Function Description

1. Device List: Max support up to 6 Box

2. Auto Loop Pattern (Button/Hot Key)

3. RGBW Pattern (Button/Hot Key)

4. HW RESET (Button/Hot Key)

5. MODE Clone/1x2/1x4/2x2

6. Support CLK SYNC

7. Support 60Hz/120Hz Modes

8. Support Multi-Box ID

9. Support Multi-Box Device Setting

10. Support H and V Bezel Adjustment

11. H Blanking Setting

12. V Blanking Setting

13. Apply Key

14. Program On/Off

72

SI-60E User Manual

Display Mode Table

Stretch (1x2)

Stretch (1x4)

Stretch (2x2)

Clone

3840x1200

7680x1200

3840x2400

1920x1200

3840x1080

7680x1080

3840x2160

1920x1080

3360x1050

6720x1050

3360x2100

1680x1050

3200x1200

6400x1200

3200x2400

1600x1200

3200x0900

6400x0900

3200x1800

1600x0900

2880x1050

5760x1050

2880x2160

1440x1050

2880x0900

5760x0900

2880x1800

1440x0900

2800x1050

5600x1050

2800x2100

1400x1050

2732x0768

5464x0768

2732x1536

1366x0768

2560x1024

5120x1024

2560x2048

1280x1024

2560x0800

5120x0800

2560x1600

1280x0800

2560x0768

5120x0768

2560x1536

1280x0768

2560x0720

5120x0720

2560x1440

1280x0720

2048x0768

4096x0768

2048x1536

1024x0768

Bezel Limit with Blanking Parameter Table

H Limit

V Limit

50

15

100

30

150

45

200

60

250

TBD

How to Setting Clone Display Step 1: Enter to Display Control Page Step 2: Go to Mode Status Press Enter Step 3: Press Up / Down Key Select to Clone Step 4: Go to UP PORT to select a Display Mode

Step 5: Go to Display Driver Control Page Step 6: Setting the two Monitor to Duplicate Mode

73

IBASE Technology Inc.

How to Setting 1x4 Display Step 1: Enter to Display Control Page Step 2: Go to Mode Status Press Enter

Step 3: Press Up / Down Key Select to Stretch Step 4: Go to Display Layout to Select 1x4

Step 5: Go to UP or DOWN Port select a Display Resolution Step 6: Go to Display Driver Control Page Step 7: Setting the two Monitor to H Combine Condition

Step 8: Adjustment H Bezel

How to Setting 2x2 Display

Step 1: Enter to Display Control Page Step 2: Go to Mode Status Press Enter

Step 3: Press Up / Down Key Select to Stretch

Step 4: Go to Display Layout to Select 2x2

Step 5: Go to UP or DOWN Port select a Display Resolution Step 6: Go to Display Driver Control Page Step 7: Setting the two Monitor to V Combine Condition

Step 8: Adjustment H Bezel Value

Step 9: Adjustment V Bezel Value

74

SI-60E User Manual

B. I/O Port Address Map

Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.

Address

Device Description

0000h-001Fh

Direct memory access controller

0000h-0CF7h

PCI bus

0040h-0043h

System timer

0050h-0053h

System timer

0070h-0077h

System CMOS/real time clock

0081h-0091h

Direct memory access controller

0093h-009Fh

Direct memory access controller

00C0h-00DFh

Direct memory access controller

00F0h-00F0h

Numeric data processor

02F8h-02FFh

Communications Port (COM2)

03B0h-03BBh

AMD Radeon E8860

03C0h-03DFh

AMD Radeon E8860

03F8h-03FFh

Communications Port (COM1)

0D00h-FFFFh

PCI bus

D000h-DFFFh

Intel(R) 8 Series/C220 Series PCI Express Root Port #7 - 8C1C

E000h-E0FFh

AMD Radeon E8860

F040h-F05Fh

Intel(R) 8 Series/C220 Series SMBus Controller - 8C22

F060h-F07Fh

Intel(R) 8 Series/C220 Series SATA AHCI Controller - 8C02

F0A0h-F0A3h

Intel(R) 8 Series/C220 Series SATA AHCI Controller - 8C02

F0B0h-F0B7h

Intel(R) 8 Series/C220 Series SATA AHCI Controller - 8C02

F0C0h-F0C3h

Intel(R) 8 Series/C220 Series SATA AHCI Controller - 8C02

F0D0h-F0D7h

Intel(R) 8 Series/C220 Series SATA AHCI Controller - 8C02

F0E0h-F0E7h

Intel(R) Active Management Technology - SOL (COM3)

75

IBASE Technology Inc.

C. Interrupt Request Lines (IRQ)

Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.

Level

Function

IRQ0

System Timer

IRQ3

Serial Port #2

IRQ4

Serial Port #1

IRQ 5

Intel(R) 8 Series/C220 Series SMBus Controller - 8C22

IRQ 13

Numeric data processor

IRQ 16

High Definition Audio Controller

IRQ 16

Intel(R) 8 Series/C220 Series USB EHCI #2 - 8C2D

IRQ 19

Intel(R) 8 Series/C220 Series SATA AHCI Controller - 8C02

IRQ 19

Intel(R) Active Management Technology - SOL (COM3)

IRQ 22

High Definition Audio Controller

IRQ 23

Intel(R) 8 Series/C220 Series USB EHCI #1 - 8C26

76

SI-60E User Manual

D. Watchdog Timer Configuration

The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sorts of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.

SAMPLE CODE: //--------------------------------------------------------------------------// // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //--------------------------------------------------------------------------#include <dos.h> #include <conio.h> #include <stdio.h> #include <stdlib.h> #include "F81846.H" //--------------------------------------------------------------------------int main (int argc, char *argv[]); void EnableWDT(int); void DisableWDT(void); //--------------------------------------------------------------------------int main (int argc, char *argv[]) {

unsigned char bBuf; unsigned char bTime; char **endptr;

char SIO; printf("Fintek 81866 watch dog program\n");

SIO = Init_F81846(); if (SIO == 0) { printf("Can not detect Fintek 81866, program abort.\n"); return(1); }//if (SIO == 0)

if (argc != 2) { printf(" Parameter incorrect!!\n"); return (1); }

bTime = strtol (argv[1], endptr, 10); printf("System will reset after %d seconds\n", bTime);

if (bTime) { EnableWDT(bTime); } else { DisableWDT(); }

return 0;

77

IBASE Technology Inc.

} //--------------------------------------------------------------------------void EnableWDT(int interval) { unsigned char bBuf;

bBuf = Get_F81846_Reg(0x2B); bBuf &= (~0x20); Set_F81846_Reg(0x2B, bBuf);

//Enable WDTO Set_F81846_LD(0x07);

//switch to logic device 7 Set_F81846_Reg(0x30, 0x01);

//enable timer bBuf = Get_F81846_Reg(0xF5);

bBuf &= (~0x0F); bBuf |= 0x52; Set_F81846_Reg(0xF5, bBuf);

//count mode is second Set_F81846_Reg(0xF6, interval);

//set timer bBuf = Get_F81846_Reg(0xFA);

bBuf |= 0x01; Set_F81846_Reg(0xFA, bBuf);

//enable WDTO output bBuf = Get_F81846_Reg(0xF5);

bBuf |= 0x20; Set_F81846_Reg(0xF5, bBuf);

//start counting } //--------------------------------------------------------------------------void DisableWDT(void) { unsigned char bBuf;

Set_F81846_LD(0x07);

78

SI-60E User Manual

//switch to logic device 7 bBuf = Get_F81846_Reg(0xFA);

bBuf &= ~0x01; Set_F81846_Reg(0xFA, bBuf);

//disable WDTO output bBuf = Get_F81846_Reg(0xF5);

bBuf &= ~0x20; bBuf |= 0x40; Set_F81846_Reg(0xF5, bBuf);

//disable WDT } //---------------------------------------------------------------------------

79

IBASE Technology Inc.

//--------------------------------------------------------------------------// // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //--------------------------------------------------------------------------#include "F81846.H" #include <dos.h> //--------------------------------------------------------------------------unsigned int F81846_BASE; void Unlock_F81846 (void); void Lock_F81846 (void); //--------------------------------------------------------------------------unsigned int Init_F81846(void) { unsigned int result; unsigned char ucDid;

F81846_BASE = 0x4E; result = F81846_BASE;

ucDid = Get_F81846_Reg(0x20); if (ucDid == 0x07)

//Fintek 81866 { goto Init_Finish; }

F81846_BASE = 0x2E; result = F81846_BASE;

ucDid = Get_F81846_Reg(0x20); if (ucDid == 0x07)

//Fintek 81866 { goto Init_Finish; }

F81846_BASE = 0x00; result = F81846_BASE;

Init_Finish: return (result); } //--------------------------------------------------------------------------void Unlock_F81846 (void) { outportb(F81846_INDEX_PORT, F81846_UNLOCK); outportb(F81846_INDEX_PORT, F81846_UNLOCK); } //--------------------------------------------------------------------------void Lock_F81846 (void) { outportb(F81846_INDEX_PORT, F81846_LOCK); }

80

SI-60E User Manual

//--------------------------------------------------------------------------void Set_F81846_LD( unsigned char LD) { Unlock_F81846(); outportb(F81846_INDEX_PORT, F81846_REG_LD); outportb(F81846_DATA_PORT, LD); Lock_F81846(); } //--------------------------------------------------------------------------void Set_F81846_Reg( unsigned char REG, unsigned char DATA) { Unlock_F81846(); outportb(F81846_INDEX_PORT, REG); outportb(F81846_DATA_PORT, DATA); Lock_F81846(); } //---------------------------------------------------------------------------

unsigned char Get_F81846_Reg(unsigned char REG) { unsigned char Result; Unlock_F81846(); outportb(F81846_INDEX_PORT, REG); Result = inportb(F81846_DATA_PORT); Lock_F81846(); return Result; } //---------------------------------------------------------------------------

81

IBASE Technology Inc.

//--------------------------------------------------------------------------// // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. // //--------------------------------------------------------------------------#ifndef __F81846_H #define __F81846_H

1 //--------------------------------------------------------------------------#define F81846_INDEX_PORT

(F81846_BASE) #define F81846_DATA_PORT

(F81846_BASE+1) //--------------------------------------------------------------------------#define F81846_REG_LD

0x07 //--------------------------------------------------------------------------#define F81846_UNLOCK

0x87 #define F81846_LOCK

0xAA //--------------------------------------------------------------------------unsigned int Init_F81846(void); void Set_F81846_LD( unsigned char); void Set_F81846_Reg( unsigned char, unsigned char); unsigned char Get_F81846_Reg( unsigned char); //--------------------------------------------------------------------------#endif //__F81846_H

IBASE Technology SI-60E User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual