IBASE Technology SI-313 User Manual

SI-313

Digital Signage Player

User’s Manual

Version 1.0 (May 2017)

ii

SI-313 User Manual

Copyright

No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).

Disclaimer

IBASE reserves the right to make changes and improvements to the products described in this document without prior notice. Every effort has been made to ensure the information in the document is correct; however, IBASE does not guarantee this document is error-free. IBASE assumes no liability for incidental or consequential damages arising from misapplication or inability to use the product or the information contained herein, nor for any infringements of rights of third parties, which may result from its use.

Trademarks

All the trademarks, registrations and brands mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

SI-313 User Manual

iii

Compliance

In a domestic environment, this product may cause radio interference in which case users may be required to take adequate measures.

This product has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with manufacturer’s instructions, may cause

harmful interference to radio communications.

WEEE

This product must not be disposed of as normal household waste, in accordance with the EU directive of for waste electrical and electronic equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by returning it to a municipal recycling collection point. Check local regulations for disposal of electronic products.

Green IBASE

This product is compliant with the current RoHS restrictions and prohibits use of the following substances in concentrations exceeding

0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm).

• Lead (Pb)

• Mercury (Hg)

• Cadmium (Cd)

• Hexavalent chromium (Cr6+)

• Polybrominated biphenyls (PBB)

• Polybrominated diphenyl ether (PBDE)

iv

SI-313 User Manual

Important Safety Information

Carefully read the precautions before using the device.

Environmental conditions:

• Lay the device horizontally on a stable and solid surface in case the device may fall, causing serious damage.

• Leave plenty of space around the device and do not block the openings for ventilation. NEVER DROP OR INSERT ANY OBJECTS OF ANY KIND INTO THE VENTIILATION OPENINGS.

• Slots and openings on the chassis are for ventilation. Do not block or cover these openings. Make sure you leave plenty of space around the device for ventilation. NEVER INSERT OBJECTS OF ANY KIND INTO THE VENTILATIN OPENINGS.

• Use this product in environments with ambient temperatures between 0˚C and 45˚C.

• DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY IS BELOW -20° C OR ABOVE 80° C. This could damage the device. The device must be used in a controlled environment.

Care for your IBASE products:

• Before cleaning the device, turn it off and unplug all cables such as power in case

a small amount of electrical current may still flow.

• Use neutral cleaning agents or diluted alcohol to clean the device chassis with a

cloth. Then wipe the chassis with a dry cloth.

• Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots

from being clogged.

WARNING

Attention during use:

• Do not use this product near water.

• Do not spill water or any other liquids on your device.

• Do not place heavy objects on the top of the device.

• Operate this device from the type of power indicated on the marking label. If you

are not sure of the type of power available, consult your distributor or local power company.

• Do not walk on the power cord or allow anything to rest on it.

• If you use an extension cord, make sure that the total ampere rating of the

product plugged into the extension cord does not exceed its limits.

Avoid Disassembly

You are not suggested to disassemble, repair or make any modification to the device. Disassembly, modification, or any attempt at repair could generate hazards and cause damage to the device, even bodily injury or property damage, and will void any warranty.

SI-313 User Manual

v

CAUTION

Danger of explosion if internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

Warranty Policy

• IBASE standard products:

24-month (2-year) warranty from the date of shipment. If the date of shipment cannot be ascertained, the product serial numbers can be used to determine the approximate shipping date.

• 3rd-party parts:

12-month (1-year) warranty from delivery for the 3rd-party parts that are not manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices, power adapter, panel and touchscreen.

＊ PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,

IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED FOR REPAIR AND SHIPPING CHARGES.

Technical Support & Services

1. Visit the IBASE website at www.ibase.com.tw to find the latest information about the product.

2. If you need any further assistance from your distributor or sales representative,

prepare the following information of your product and elaborate upon the problem.

• Product model name

• Product serial number

• Detailed description of the problem

• The error messages in text or in screenshots if there is any

• The arrangement of the peripherals

• Software in use (such as OS and application software, including the version

numbers)

3. If repair service is required, you can download the RMA form at

http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and

contact your distributor or sales representative.

vi

SI-313 User Manual

Table of Contents

Compliance.................................................................................................... iii

Important Safety Information ....................................................................... iv

WARNING ...................................................................................................... iv

CAUTION ........................................................................................................ v

Warranty Policy .............................................................................................. v

Technical Support & Services ...................................................................... v

Chapter 1 General Information ................................................................ 1

1.1 Introduction ............................................................................................. 2

1.2 Features .................................................................................................. 2

1.3 Packing List ............................................................................................ 3

1.4 Optional Accessories .............................................................................. 3

1.5 Specifications .......................................................................................... 4

1.6 Overview ................................................................................................. 6

1.7 Dimensions ............................................................................................. 8

Chapter 2 Hardware Installation & Motherboard Information .............. 9

2.1 Essential Installations Before You Begin ............................................... 10

2.1.1 Memory Installation ................................................................ 10

2.1.2 Mini PCIe & M.2 Network Cards Installation ........................... 11

2.1.3 WiFi / 3G / 4G Antenna Installation ......................................... 12

2.1.4 Wall Mount Installation ............................................................ 13

2.2 Setting the Jumpers .............................................................................. 15

2.2.1 How to Set Jumpers ............................................................... 15

2.3 Jumper & Connector Locations on Motherboard ................................... 16

2.4 Jumpers Quick Reference ..................................................................... 18

2.4.1 CMOS Data Clearance (JP1) ............................................... 18

2.4.2 ATX / AT Power Mode Connector (JP2) ............................... 19

2.5 Connectors Quick Reference ................................................................ 20

2.5.1 Power Button (SW1) ............................................................ 21

2.5.2 EDID Clearance Button (SW2) ............................................. 21

2.5.3 LED Indicators for Power & HDD (LED4, LED5) .................. 22

2.5.4 DC Power Input (CN1) ......................................................... 22

2.5.5 HDMI 2.0 Port (CN2, CN3, CN4) .......................................... 23

SI-313 User Manual

vii

2.5.6 LAN Port (CN5) .................................................................... 23

2.5.7 Dual USB 3.0 Ports (CN6) .................................................... 23

2.5.8 Dual USB 2.0 Ports (CN7) .................................................... 24

2.5.9 COM1 RS-232 Port (CN8) .................................................... 24

2.5.10 Audio Jack (CN9, CN10) ...................................................... 25

2.5.11 CPU Fan Power Connector (J1) ........................................... 25

2.5.12 USB 2.0 Ports Header (J2) ................................................... 26

2.5.13 COM2 RS-232 Port (J3) ....................................................... 26

2.5.14 System Function Connector (J4) .......................................... 27

2.5.15 NGFF M.2 Connector (J6, J13) ............................................ 27

2.5.16 SIM Card Socket (J8) ........................................................... 28

2.5.17 Mini PCIe Connector (J10) ................................................... 28

2.5.18 DDR4 SO-DIMM (J11, J12) .................................................. 28

2.5.19 Digital I/O Connector (J19) ................................................... 29

Chapter 3 Driver Installation ................................................................. 30

3.1 Introduction ........................................................................................... 31

3.2 AMD Merlin Falcon Graphics Drivers Installation .................................. 31

3.3 HD Audio Driver Installation .................................................................. 32

3.4 LAN Driver Installation .......................................................................... 33

Chapter 4 BIOS Setup ............................................................................ 34

4.1 Introduction ........................................................................................... 35

4.2 BIOS Setup ........................................................................................... 35

4.3 Main Settings ........................................................................................ 36

4.4 Advanced Settings ................................................................................ 37

4.4.1 IDE Configuration ................................................................... 38

4.4.2 ACPI Shutdown Temperature ................................................. 38

4.4.3 iSMART Controller .................................................................. 39

4.4.4 Super IO Configuration ........................................................... 40

4.4.5 Hardware Monitor ................................................................... 41

4.4.6 CPU Configuration .................................................................. 42

4.4.7 SATA Configuration ................................................................ 43

4.4.8 CSM Configuration ................................ ................................. 44

4.4.9 USB Configuration .................................................................. 45

4.5 Chipset Settings .................................................................................... 46

4.5.1 South Bridge ........................................................................... 47

4.5.2 North Bridge ........................................................................... 48

4.6 Security Settings ................................................................................... 49

4.7 Boot Settings......................................................................................... 50

4.8 Save & Exit Settings.............................................................................. 51

viii

SI-313 User Manual

Appendix ...................................................................................................... 52

A. I/O Port Address Map ............................................................................ 53

B. Interrupt Request Lines (IRQ) ............................................................... 56

C. Watchdog Timer Configuration .............................................................. 57

1

Chapter 1 General Information

The information provided in this chapter includes:

• Features

• Packing List

• Specifications

• Optional Accessories

• Overview

• Dimensions

2

SI-313 User Manual

1.1 Introduction

SI-313, a product code of IBASE digital signage player series, is a mid-range system with iSMART and capable of auto-scheduling for general applications. It is designed with the feature of segregated flow ventilation. The device is powered by the AMD 3rd Gen. Embedded R-Series SOC APU, and outputs through HDMI 4K ultra high definition video playback at 60 Hz. The device is able to be operated at the ambient operating temperature ranging from 0 ~ 45 °C, and even lower from -20 ~ 80 °C for storage.

1.2 Features

• iSMART for auto-scheduler and power resume

• AMD 3

rd

Gen. Embedded R-series SOC APU, up to 35W

• Integrated next-generation AMD Radeon

TM

HD GPU

• AMD Eyefinity video wall display configuration

• Display via HDMI 2.0 (3 ports) for 4K at 60 Hz with EDID emulation

• Gigabit Ethernet & RS-232 COM port

• Dual DDR4 SO-DIMM, 2133 MHz at 1.2V, expandable up to 32 GB

• SIM card slot

• WiFi networks, Bluetooth

• Options of 4G LTE or TV tuner

• Segregated flow ventilation design

General Information

SI-313 User Manual

3

1

1.3 Packing List

Your SI-313-N package should include the items listed below. If any of the items below is missing, contact the distributor or the dealer from whom you purchased the product.

• SI-313 Digital Signage Player (with Rack Mount Kit) x 1

• Power Adapter x 1

• Power Cord x 1

• HDMI Cable Holder x 1

• Screws for HDMI Cable Holder x 2

• Screws for Rack Mount Kit x 4

• Disk (including drivers and this user manual) x 1

1.4 Optional Accessories

IBASE provide optional accessories as follows. Please contact us or your dealer if you need any.

• WiFi Cable Kit

4

SI-313 User Manual

1.5 Specifications

Product

SI-313

System

Mainboard

MBD313

Operating System

Windows 7 / 8 / 10 / Linux

CPU

AMD 3rd Gen. Embedded R-Series SoC APU (FP4 BGA) CPU Clock (Max/Base): 2.7GHz / 3.6 GHz

Chipset

AMD integrated SoC

Cache

Up to 4 MB

Memory

2 x DDR4 SO-DIMM 4GB 2133 MHz, dual channel, expandable up to 32GB

Graphics

Next-gen. AMD RadeonTM HD GPU integrated

Super I/O

Fintek F81846AD

Storage

• 1 x NGFF M.2 (3042) B key

• 1 x NGFF M.2 (2280) M key

Power Requirement

12V DC-in

Power Supply

150W power adapter

Wireless

WiFi module 802.11 a/b/g/n (Optional)

Watchdog

Watchdog Timer 256 segments, 0, 1, 2…255 sec/min

iSMART

V3.2

System Fan

1 x CPU fan

Chassis

Aluminum and SGCC, black & white

Mounting

Standard system bracket Slim design with wall mount holes

Dimensions (W x H x D)

215.6 x 33 x 150 mm (8.49” x 1.3” x 5.9”)

Net Weight

1.55 kg (3.42 lb)

Certificate

CE, FCC Class B, UL, CCC

General Information

SI-313 User Manual

5

1

I/O Ports

HDMI

3 x HDMI 2.0, choose either way:

• Use 2 ports for 4K (3840 x 2160) display at 60 Hz (via

HDMI 2.0) (If 3 displays are connected, the resolutions will be 4K, 4K, 1080p per the sequence of connection.)

• Use 3 port for 4K (3840 x 2160) display at 30 Hz (via

HDMI1.4)

LAN

1 x GbE RJ45 LAN port

Serial

• 1 x RJ45 for COM1 RS-232 port

• 1 x on-board pin-header for COM2 RS-232 port

USB

• 2 x USB 3.0

• 2 x USB 2.0

Audio Jack

• 1 x Line-Out

• 1 x Microphone Input

Power Jack

1 x DC-in power jack

Expansion

• 1 x M.2 (3042) B Key with PCIe (x2) for storage / WiFi / BT /

4G LTE options

• 1 x M.2 (2280) M Key with SATA

• 1 x Mini-PCIe (x1) for WiFi / BT / TV tuner / 4G LTE options

• 1 x SIM card slot

Environment

Temperature

• Operating: 0 ~ 45 °C (32 ~ 113 °F)

• Storage: --20 ~ 80 °C (-4 ~ 176 °F)

Relative Humidity

10 ~ 90% (non-condensing)

Vibration Protection

M.2: Operating, random vibration 5 grms (5~500Hz)

All specifications are subject to change without prior notice.

6

SI-313 User Manual

1.6 Overview

Top View

Oblique View

General Information

SI-313 User Manual

7

1

I/O View

No.

Name

No.

Name

1

DC Power Input

8

Audio Line-Out

2

HDMI 2.0 Port

9

Microphone Input

3

EDID Clearance Button*

10

Power Button

4

LAN Port

11

LED Indicator for Power

5

USB 3.0

12

LED Indicator for HDD

6

USB 2.0

13

Mounting Kit

7

COM Port

14

Antenna Hole

* Be sure to press the EDID Clearance Button shortly so as to clear the EDID

register if any connected display/monitor is unable to be recognized, or when the image displayed cannot not be resampled to fit the screen.

8

SI-313 User Manual

1.7 Dimensions

Unit: mm

9

Chapter 2 Hardware Installation & Motherboard Information

The information provided in this chapter includes:

• Essential installations before you begin

• Information and locations of connectors

10

SI-313 User Manual

2.1 Essential Installations Before You Begin

2.1.1 Memory Installation

There are two SO-DIMM DDR4 memory slots inside SI-313 for a maximum total memory of 32 GB. To install the modules, locate the memory slot on the board and perform the following steps:

1. Align the key of the memory module with that on the memory slot and insert the module slantwise.

2. Gently push the module in an upright position until the clips of the slot close to hold the module in place when the module touches the bottom of the slot.

To remove the module, press the clips outwards with both hands.

Motherboard Information

SI-313 User Manual

11

2

2.1.2 Mini PCIe & M.2 Network Cards Installation

1. Align the key of the mini PCIe card to the Mini PCIe interface, and insert the card slantwise.

(Insert the M.2 network card in the same way.)

2. Push the mini PCIe card down, fix it with 2 screws. (Fix the M.2 network card with a screw.)

Mini PCIe:

M.2:

12

SI-313 User Manual

2.1.3 WiFi / 3G / 4G Antenna Installation

Thread the WiFi / 3G / 4G antenna extension cable through an antenna hole of the front I/O cover and fasten the antenna as shown below. Then apply adhesive to the edge of the hex nut behind the front I/O cover to prevent the extension cable from falling if the cable becomes loose.

1. Thread and fasten the hex nut and the washer. Then install the antenna.

2. Apply adhesive around here.

Info: The diameter of the nut is around 6.35 mm (0.25”-36UNC).

Motherboard Information

SI-313 User Manual

13

2

2.1.4 Wall Mount Installation

Note: Before mounting the system on wall, ensure that you are following all

applicable building and electric codes.

Requirements

When mounting, ensure that you have enough room for power and signal cable routing, and have good ventilation for power adapter. The method of mounting must be able to support weight of the SI-313 plus the suspension weight of all the cables to be attached to the system. Use the following methods for mounting your system:

Selecting the Location

Plan the mounting location thoroughly. Locations such as walkway areas, hallways, and crowded areas are not recommended. Mount the product to a flat, sturdy, structurally sound column or wall surface.

The best mounting surface is a standard countertop, cabinet, table, or other structure that is minimally the width and length of the product. This will reduce the risk that someone may accidentally walk into and damage the product. Local laws governing the safety of individuals might require this type of consideration.

Selecting the type of wall construction

1. Mounting on a hollow wall

• Wood surface Use construction-grade wood and the recommended minimum

thickness is 38 x 25.4 mm (1.5” x 10”).

Note: This method provides the most reliable attachment for the

product with little risk that the product may come loose or require ongoing maintenance.

• Drywall Drywall over wood studs is acceptable.

2. Mounting on a solid concrete or brick wall with flat and smooth surface

14

SI-313 User Manual

Wall mount installation instructions:

Prepare at least 4 screws (M3) to install the device on wall as below.

You can install your SI-313 on plastic (LCD monitor), wood, drywall surface over studs, or a solid concrete or metal plane directly. The types of fasteners required are dependent on the type of wall construction.

Fasteners are not supplied in the product package. You will need to prepare the fasteners. Choose fasteners that are rated either Medium Duty or Heavy Duty. To assure proper fastener selection and installation, follow the fastener manufacturer’s recommendations.

Motherboard Information

SI-313 User Manual

15

2

2.2 Setting the Jumpers

Set up and configure your SI-313 by using jumpers for various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your use.

2.2.1 How to Set Jumpers

Jumpers are short-length conductors consisting of several metal pins with a non-conductive base mounted on the circuit board. Jumper caps are used to have the functions and features enabled or disabled. If a jumper has 3 pins, you can connect either PIN1 to PIN2 or PIN2 to PIN3 by shorting.

A 3-pin jumper

A jumper cap

Refer to the illustration below to set jumpers.

Pin closed

Oblique view

Schematic illustration in the manual

Open

1-2

2-3

When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On.

When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off.

Pin# 1

2

3

1 2 3

16

SI-313 User Manual

2.3 Jumper & Connector Locations on Motherboard

Motherboard: MBD313

MBD313 - top

SIO

J4

781

2

J2

J3

7

8

1

2

19

AMD 3rd Gen. Embedded R-Series SOC APU

LED5

LED4

SW1

CN10

CN9

CN8

CN7 CN6

CN5

CN1

CN4

CN3

CN2

J1

1

Motherboard Information

SI-313 User Manual

17

2

3

MBD313 - bottom

J7

J12 J11

JP2

J18

J19

J14

SW2

J13

J15

J16

J17

J10

J6

J9

J8

JP1

144

1

2

143

146 145

260

259

143

2

1

144

145145

259

260

Open

Lock

Battery

1

121

1

2

910 9

1

2

9

10

11

BZ1

18

SI-313 User Manual

2.4 Jumpers Quick Reference

Jumper:

Function

Connector Name

Page

CMOS Data Clearance

JP1

18

ATX / AT Power Mode Selection

JP2

19

2.4.1 CMOS Data Clearance (JP1)

Function

Pin closed

Illustration

Normal

(default)

1-2

Clear CMOS

2-3

1

Motherboard Information

SI-313 User Manual

19

2

2.4.2 ATX / AT Power Mode Connector (JP2)

Function

Pin closed

Illustration

ATX

(default)

1-2

AT

2-3

1

20

SI-313 User Manual

2.5 Connectors Quick Reference

I/O coastline connectors:

Function

Connector Name

Page

Power Button

SW1

21

EDID Clearance Button

SW2

21

LED Indicator

LED4 (Red, for Power) LED5 (Green, for HDD)

22

DC Power Input

CN1

22

HDMI 2.0 Port

CN2,CN3,CN4

23

LAN Port (GbE)

CN5

23

Dual USB 3.0 Ports

CN6

23

Dual USB 2.0 Ports

CN7

24

COM1 RS-232 Port

CN8

24

Audio Jack

CN9 (Line-out) CN10 (Microphone Input)

25

On-board connectors:

Function

Connector Name

Page

CPU Fan Power Connector

J1

25

USB 2.0 Ports Header

J2

26

COM2 RS232 Port

J3:

26

System Function Connector

J4

27

NGFF M.2 Connector

J6 (M-KEY 2280) J13 (B-KEY 3042)

27

SIM Card Socket

J8

28

Mini PCIE Connectors

J10

28

DDR4 SO-DIMM

J11, J12

28

Digital I/O Header

J19

29

Factory Use Only

J7, J9, J14, J15, J16, J17, J18

--

Motherboard Information

SI-313 User Manual

21

2

2.5.1 Power Button (SW1)

2.5.2 EDID Clearance Button (SW2)

Note: Be sure to press this button shortly so as to clear the EDID register if

any connected display/monitor is unable to be recognized, or when the image displayed cannot not be resampled to fit the screen.

22

SI-313 User Manual

2.5.3 LED Indicators for Power & HDD (LED4, LED5)

LED4 LED5

LED4 is the red LED indicator for power status. It stays on (not blinks) as the device is on.

LED5 is the green LED indicator for HDD. When HDD is being read, it blinks.

2.5.4 DC Power Input (CN1)

Assigment

1

Ground

3

+12V

2

Ground

4

+12V

4 3

2 1

Motherboard Information

SI-313 User Manual

23

2

2.5.5 HDMI 2.0 Port (CN2, CN3, CN4)

2.5.6 LAN Port (CN5)

2.5.7 Dual USB 3.0 Ports (CN6)

24

SI-313 User Manual

2.5.8 Dual USB 2.0 Ports (CN7)

2.5.9 COM1 RS-232 Port (CN8)

Assigment

1

DSR (Data set ready)

6

DCD (Data carrier detect)

2

Ground

7

DTR (Data terminal ready)

3

Ground

8

CTS (Clear to send)

4

TX (Transmit)

9

RTS (Request to send)

5

RX (Receive)

10

RI (Ring indicator)

101

Motherboard Information

SI-313 User Manual

25

2

2.5.10 Audio Jack (CN9, CN10)

CN9: Line-out

CN10: Microphone Input

2.5.11 CPU Fan Power Connector (J1)

Assigment

1

Ground

2

+12V

3

Rotation detection

1

26

SI-313 User Manual

2.5.12 USB 2.0 Ports Header (J2)

Assigment

1

+5V

5

Data+

2

+5V

6

Data+

3

Data-

7

Ground

4

Data-

8

Ground

2.5.13 COM2 RS-232 Port (J3)

Assigment

1

DCD (Data carrier detect)

6

CTS (Clear to send)

2

DSR (Data set ready)

7

DTR (Data terminal ready)

3

RXD (Receive data)

8

RI (Ring indicator)

4

RTS (Request to send)

9

Ground

5

TXD (Transmit data)

7

8 2

1

1 2

9

Motherboard Information

SI-313 User Manual

27

2

2.5.14 System Function Connector (J4)

Assigment

1

Power BTN

5

Reset BTN

2

Power BTN

6

Reset BTN

3

HDD LED+

7

+5V

4

HDD LED-

8

+5VSB

2.5.15 NGFF M.2 Connector (J6, J13)

J6 is a M.2 M-Key (2280) connector with SATA.

J13 is a M.2 B-Key (3042) connector with PCIe (x2) , USB 2.0, USB 3.0, and

SATA.

8

7 1

2

28

SI-313 User Manual

2.5.16 SIM Card Socket (J8)

2.5.17 Mini PCIe Connector (J10)

J10 is a Mini PCIe connector with PCI-e, USB and SIM.

2.5.18 DDR4 SO-DIMM (J11, J12)

J12 J11

s

Open

Lock

Motherboard Information

SI-313 User Manual

29

2

2.5.19 Digital I/O Connector (J19)

Assigmentd

Assigment

1

Ground

6

OUT0

2

+5V

7

IN3

3

OUT3

8

IN1

4

OUT1

9

IN2

5

OUT2

10

IN0

9

1

10

2

30

Chapter 3 Driver Installation

The information provided in this chapter includes:

• AMD Merlin Falcon Graphics Drivers Installation

• HD Audio Driver Installation

• LAN Driver Installation

Driver Installation

SI-313 User Manual

31

3

3.1 Introduction

This section describes the installation procedures for software drivers. The software drivers are in a disk enclosed with the product package. If you find anything missing, please contact the distributor where you made the purchase.

3.2 AMD Merlin Falcon Graphics Drivers Installation

1. Insert the disk enclosed in the package. Click System and then AMD Merlin Falcon Graphics Drivers Installation.

2. Click Install to cintinue.

3. Select the desired drivers and click Install.

4. The driver has been completely installed. You are suggested to restart the computer for changes to take effect.

32

SI-313 User Manual

3.3 HD Audio Driver Installation

1. Insert the disk enclosed in the package with the board. Click System and then Realtek High Definition Audio Driver.

2. On the Welcome screen of the InstallShield Wizard, click Next.

3. After reading the descriptions of the setup options, click Next to start installation.

4. The driver has been completely installed. You are suggested to restart the computer and for changes to take effect.

Driver Installation

SI-313 User Manual

33

3

3.4 LAN Driver Installation

1. Insert the disk enclosed in the package with the board. Click System and then Realtek GbE _FE Ethernet PCI-E NIC Driver.

2. When the Welcome screen appears, click Next and then Install to contiune installation.

3. The driver has been completely installed. You are suggested to restart the

computer for changes to take effect.

34

Chapter 4 BIOS Setup

This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows:

• Main Settings

• Advanced Settings

• Chipset Settings

• Security Settingss

• Book Settings

• Save & Exit

BIOS Setup

SI-313 User Manual

35

4

4.1 Introduction

The BIOS (Basic Input/Output System) installed in the ROM of your computer system supports Intel® processors. The BIOS provides critical low-level support for standard devices such as disk drives, serial ports and parallel ports. It also provides password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.

4.2 BIOS Setup

The BIOS provides a Setup utility program for specifying the system configurations and settings. The BIOS ROM of the system stores the Setup utility. When you turn on the computer, the BIOS is immediately activated. Press the <Del> key immediately allows you to enter the Setup utility. If you are a little bit late pressing the <Del> key, POST (Power On Self Test) will continue with its test routines, thus preventing you from invoking the Setup.

If you still need to enter Setup, restart the system by pressing the ”Reset” button or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys.

You can also restart by turning the system Off and back On again. The following message will appear on the screen:

Press <DEL> to Enter Setup

In general, press the arrow keys to highlight items, <Enter> to select, the <PgUp> and <PgDn> keys to change entries, <F1> for help, and <Esc> to quit.

When you enter the BIOS Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices.

Warning: It is strongly recommended that you avoid making any changes to

the chipset defaults.

These defaults have been carefully chosen by both AMI and your

system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases.

36

SI-313 User Manual

4.3 Main Settings

BIOS Setting

Description

System Language

Choose the system default language.

System Date

Sets the date. Use the <Tab> key to switch between the data

elements.

System Time

Set the time. Use the <Tab> key to switch between the data

elements.

BIOS Setup

SI-313 User Manual

37

4

4.4 Advanced Settings

This section allows you to configure, improve your system and allows you to set up some system features according to your preference.

38

SI-313 User Manual

4.4.1 IDE Configuration

4.4.2 ACPI Shutdown Temperature

BIOS Setup

SI-313 User Manual

39

4

4.4.3 iSMART Controller

BIOS Setting

Description

Power-On after Power failure

Enables / Disables the system to be turned on automatically after a power failure.

Schedule Slot 1 / 2

Sets up the hour / minute for system powe-on.

40

SI-313 User Manual

4.4.4 Super IO Configuration

BIOS Setting

Description

Serial Port Configuration

Sets parameters of Serial Ports (COMA). Enables / Disables the serial port and select

an optimal setting for the Super IO device.

BIOS Setup

SI-313 User Manual

41

4

4.4.5 Hardware Monitor

BIOS Setting

Description

CPU smart fan control

Enables / Disables the smart fan feature. Disabled (default)

• 50 ℃

• 60 ℃

• 70 ℃

• 80 ℃

• 90 ℃

Temperatures / Voltages

These fields are the parameters of the hardware monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status.

Shutdown Temperature

This field enables or disables the Shutdown Temperature

42

SI-313 User Manual

4.4.6 CPU Configuration

BIOS Setting

Description

Node 0 Information

Shows the memory information related to Node 0.

BIOS Setup

SI-313 User Manual

43

4

4.4.7 SATA Configuration

BIOS Setting

Description

SATA Controller(s)

Enables / Disables SATA devices.

SATA Mode Selection

Determines how the SATA controller(s) operate.

• AHCI Mode.

• RAID Mode.

Serial ATA Ports

Enables / Disables Serial Ports.

Hot Plug

Designates this port as Hot Pluggable.

44

SI-313 User Manual

4.4.8 CSM Configuration

BIOS Setting

Description

CSM Support

Enables or disables CSM support.

BIOS Setup

SI-313 User Manual

45

4

4.4.9 USB Configuration

BIOS Setting

Description

Legacy USB SUpport

• Enable: Enables Ledacy USB Support.

• Auto: Disables legacy support if no USB

devices are connected.

• Disable: Keeps USB devices available only

for EFI applications.

XHCI / EHCI Hand-off

This is a workaround for OSes without XHCI / EHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.

USB Mass Storage Driver Support

Enables / Disables the support for USB mass storage driver.

Port 60/64 Emulation

Enables I/O port 60h/64h emulation support. This should be enabled for the complete USB keyboard legacy support for non-USB aware OSes.

USB Transfer time-out

The time-out value for Control, Bulk, and Interrupt transfers.

Device reset time-out

Seconds of delaying execution of start unit command to USB mass storage device.

Device power-up delay

The maximum time the device will take before it properly reports itself to the Host Controller.

“Auto” uses default value for a Root port it is 100ms. But for a Hub port, the delay is taken from Hub descriptor.

46

SI-313 User Manual

4.5 Chipset Settings

BIOS Setting

Description

Sourth Bridge

South Bridge parameters

North Bridge

North Bridge parameters

BIOS Setup

SI-313 User Manual

47

4

4.5.1 South Bridge

4.5.1.1. SATA Configuration

BIOS Setting

Description

SB SATA / USB Configuration

Options for SATA Configuration

48

SI-313 User Manual

4.5.1.2. XHCI Controller

4.5.2 North Bridge

BIOS Setting

Description

Socket 0 Information

Displays the information related to Socket 0..

BIOS Setup

SI-313 User Manual

49

4

4.6 Security Settings

BIOS Setting

Description

Administrator Password

Sets an administrator password for the setup utility.

User Password

Sets a user password.

50

SI-313 User Manual

4.7 Boot Settings

BIOS Setting

Description

Setup Prompt Timeout

Number of seconds to wait for setup activation key.

65535 (0xFFFF) means indefinite waiting.

Bootup NumLock State

Selects the keyboard NumLock state.

Quiet Boot

Enables / Disables Quiet Boot option.

Fast Boot

Enables / Disables boot with initialization of a minimal set of devices required to launch the active boot option. There no effect for BBS boot options.

Fixed Boot Order Priorities

Sets the system boot order.

Boot Option Priorities

Sets the system boot order.

BIOS Setup

SI-313 User Manual

51

4

4.8 Save & Exit Settings

BIOS Setting

Description

Save Changes and Exit

Exits system setup after saving the changes.

Discard Changes and Exit

Exits system setup without saving any changes.

Save Changes and Reset

Resets the system after saving the changes.

Discard Changes and Reset

Resets system setup without saving any changes.

Save Changes

Saves changes done so far to any of the setup options.

Discard Changes

Discards changes done so far to any of the setup options.

Restore Defaults

Restores / Loads defaults values for all the setup options.

Save as User Defaults

Saves the changes done so far as user defaults.

Restore User Defaults

Restores the user defaults to all the setup options.

52

Appendix

This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration.

• I/O Port Address Map

• Interrupt Request Lines (IRQ)

• Digital I/O Sample Code

• Watchdog Timer Configuration

Appendix

SI-313 User Manual

53

A. I/O Port Address Map

Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.

Address

Device Description

0x00000A00-0x00000A0F

Motherboard resources

0x00000A20-0x00000A2F

Motherboard resources

0x00000A10-0x00000A1F

Motherboard resources

0x00000000-0x0000000F