IBASE Technology IB811 User Manual

The information contained in this document has been carefully researched and is, to the best of our knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or consequential, resulting from the use of the information provided herein. Our products are not intended for use in systems in which failures of product could result in personal injury. All trademarks mentioned herein are property of their respective owners. All specifications are subject to change without notice.

Manual

iBASE

IB811

IB811F Series

Intel® Pentium® / Celeron® /

Atom™ x7 / x5 SoC

3.5” Disk-Size SBC

User’s Manual

Version 1.0

(Feb. 2017)

ii

IB811F Series User’s Manual

Copyright

No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).

Disclaimer

IBASE reserves the right to make changes and improvements to the products described in this document without prior notice. Every effort has been made to ensure the information in the document is correct; however, IBASE does not guarantee this document is error-free. IBASE assumes no liability for incidental or consequential damages arising from misapplication or inability to use the product or the information contained herein, nor for any infringements of rights of third parties, which may result from its use.

Trademarks

All the trademarks, registrations and brands mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

IB811F Series User’s Manual

iii

Compliance

This product has passed CE tests for environmental specifications and limits. This product is in accordance with the directives of the European Union (EU). In a domestic environment, this product may cause radio interference in which case users may be required to take adequate measures.

This product has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with manufacturer’s

instructions, may cause harmful interference to radio communications.

WEEE

This product must not be disposed of as normal household waste, in accordance with the EU directive of for waste electrical and electronic equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by returning it to a municipal recycling collection point. Check local regulations for disposal of electronic products.

Green IBASE

This product is compliant with the current RoHS restrictions and prohibits use of the following substances in concentrations exceeding 0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm).

• Lead (Pb)

• Mercury (Hg)

• Cadmium (Cd)

• Hexavalent chromium (Cr6+)

• Polybrominated biphenyls (PBB)

• Polybrominated diphenyl ether (PBDE)

iv

IB811F Series User’s Manual

Important Safety Information

Carefully read the precautions before using the board.

Environmental conditions:

 Use this product in environments with ambient temperatures between

0˚C and 60˚C, or -40 and 85 ˚C.

 Do not leave this product in an environment where the storage

temperature may be below -40° C or above 110° C. To prevent from damages, the product must be used in a controlled environment.

Care for your IBASE products:

 Before cleaning the PCB, unplug all cables and remove the battery.  Clean the PCB with a circuit board cleaner or degreaser, or use cotton

swabs and alcohol.

 Vacuum the dust with a computer vacuum cleaner to prevent the fan

from being clogged.

WARNING

Attention during use:

 Do not use this product near water.  Do not spill water or any other liquids on this product.  Do not place heavy objects on the top of this product.

Anti-static precautions

 Wear an anti-static wrist strap to avoid electrostatic discharge.  Place the PCB on an anti-static kit or mat.  Hold the edges of PCB when handling.  Touch the edges of non-metallic components of the product instead of

the surface of the PCB.

 Ground yourself by touching a grounded conductor or a grounded bit of

metal frequently to discharge any static.

CAUTION

Danger of explosion if the internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point.

IB811F Series User’s Manual

v

Warranty Policy

 IBASE standard products:

24-month (2-year) warranty from the date of shipment. If the date of shipment cannot be ascertained, the product serial numbers can be used to determine the approximate shipping date.

 3rd-party parts:

12-month (1-year) warranty from delivery for the 3rd-party parts that are not manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices, power adapter, panel and touchscreen.

＊ PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,

IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED FOR REPAIR AND SHIPPING CHARGES.

Technical Support & Services

1. Visit the IBASE website at

www.ibase.com.tw to find the latest

information about the product.

2. If you need any further assistance from your distributor or sales representative, prepare the following information of your product and elaborate upon the problem.

 Product model name  Product serial number  Detailed description of the problem  The error messages in text or in screenshots if there is any  The arrangement of the peripherals  Software in use (such as OS and application software, including the

version numbers)

3. If repair service is required, you can download the RMA form at

http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the

form and contact your distributor or sales representative.

vi

IB811F Series User’s Manual

Table of Contents

Compliance ..................................................................................... iii

Important Safety Information ........................................................ iv

Warranty Policy ............................................................................... v

Technical Support & Services ....................................................... v

Chapter 1 General Information ............................................. 1

1.1 Introduction ......................................................................................... 2

1.2 Features .............................................................................................. 2

1.3 Packing List ......................................................................................... 3

1.4 Optional Accessories ........................................................................... 3

1.5 Specifications ...................................................................................... 4

1.6 Block Diagram ..................................................................................... 7

1.7 Overview ............................................................................................. 8

1.8 Dimensions ....................................................................................... 10

Chapter 2 Hardware Configuration ........................................ 11

2.1 Essential Installations Before You Begin ........................................... 12

2.1.1 Installing the Memory ........................................................... 12

2.2 Setting the Jumpers .......................................................................... 13

2.2.1 How to Set Jumpers ............................................................. 13

2.3 Jumper & Connector Locations ......................................................... 14

2.4 Jumpers Quick Reference ................................................................. 15

2.4.1 LVDS Panel Brightness Selection (JP1) .............................. 15

2.4.2 LVDS Panel Power Selection (JP2) ..................................... 16

2.4.3 eDP Panel Power Selection (JP3) ....................................... 16

2.4.4 eDP / LVDS Panel Selection (JP4) ...................................... 17

2.4.5 ATX / AT Power Selection (JP5) ......................................... 17

2.4.6 CMOS Data Clearance (JP6) .............................................. 18

2.4.7 ME Register Clearance (JP7) .............................................. 18

2.5 Connectors Quick Reference............................................................. 19

2.5.1 eDP Connector (CN1) ......................................................... 20

2.5.2 SATA III Connector (CN2, CN3) .......................................... 21

2.5.3 LAN Ports (CN4) ................................................................. 21

2.5.4 USB 3.0 Ports (CN5, CN6) .................................................. 21

IB811F Series User’s Manual

vii

2.5.5 Console COM1 (RJ10) RS-232/422/485 Port (CN7) ............22

2.5.6 DisplayPort (CN8) ................................................................23

2.5.7 HDMI Port (CN9) .................................................................23

2.5.8 LCD Backlight Connector (J2) .............................................23

2.5.9 LVDS Connector (J1, J3) .....................................................24

2.5.10 Audio Connector (J4) ...........................................................25

2.5.11 DDR3L SO-DIMM Slot (J5, J8) ............................................25

2.5.12 USB 2.0 Connector (J6) .......................................................26

2.5.13 Amplifier Connector (J7) ......................................................26

2.5.14 SATA HDD Power Connector (J10) .....................................27

2.5.15 Mini PCIe / mSATA Slot (J11) .............................................27

2.5.16 COM2 / COM3 / COM4 RS-232 Port (J16, J17, J12) ...........28

2.5.17 M.2 (B key) 3042 Slot (J14) .................................................28

2.5.18 Front Panel Connector (J13) ................................................29

2.5.19 Digital I/O Connector (J18) ..................................................30

2.5.20 DC Power Input Connector (J19) .........................................30

Chapter 3 Drivers Installation ............................................. 31

3.1 Introduction ........................................................................................32

3.2 Intel® Chipset Software Installation Utility ..........................................33

3.3 VGA Driver Installation.......................................................................35

3.4 HD Audio Driver Installation ...............................................................37

3.5 Intel® Trusted Execution Engine Drivers ............................................39

3.6 Intel® Serial IO Drivers .......................................................................41

3.7 LAN Driver Installation .......................................................................43

Chapter 4 BIOS Setup .......................................................... 45

4.1 Introduction ........................................................................................46

4.2 BIOS Setup........................................................................................46

4.3 Main Settings .....................................................................................48

4.4 Advanced Settings .............................................................................49

4.4.1 ACPI Computing ...................................................................50

4.4.2 LVDS (eDP/DP) Configuration ..............................................51

4.4.3 F81866 Super IO Configuration ............................................52

4.4.4 Fintek Super IO Hardware Monitor........................................54

4.4.5 M.2 Setup .............................................................................55

4.4.6 CPU Configuration ................................................................56

4.4.7 AMI Graphic Output Protocol Policy......................................57

4.4.8 Network Stack Configuration ................................................58

viii

IB811F Series User’s Manual

4.4.9 CMS Configuration ............................................................... 59

4.4.10 USB Configuration ............................................................... 60

4.5 Chipset Settings ................................................................................ 61

4.5.1 North Bridge ......................................................................... 61

4.5.2 South Cluster Configuration ................................................. 62

4.6 Security Settings ............................................................................... 67

4.7 Boot Settings ..................................................................................... 68

4.8 Save & Exit Settings .......................................................................... 69

Appendix ........................................................................................ 70

A. I/O Port Address Map ........................................................................ 71

B. Interrupt Request Lines (IRQ) ............................................................ 74

C. Watchdog Timer Configuration .......................................................... 76

1

Chapter 1 General Information

The information provided in this chapter includes:

 Features

 Packing List

 Block Diagram

 Specifications

 Board Overview

 Board Dimensions

2

IB811F Series User’s Manual

1.1 Introduction

IB811F is a 3.5” disk-size single board computer based on the platform of Intel® Atom™ x7/x5, Pentium® or Celeron®. It features both DisplayPort and HDMI at coastline, and on-board headers for eDP / 24-bit dual channel LVDS

interfaces for video display. It is able to be operated at the ambient operating temperature ranging from 0 ~ 60 °C, and even from -40 ~ 85 °C for models of wide temperature.

Photo of IB811F-420

1.2 Features

 3.5” disk-size SBC with Intel® Atom™ x7-E3950 / x5-E3930 /

Pentium® N4200 / Celeron® N3350

 2 x DDR3L-1600/1866 SO-DIMM slots, expandable up to 8GB

 1 x HDMI, 1 x DisplayPort, eDP / 24 bit dual channel LVDS

 2 x GbE LAN, 4 x USB 3.0, 2 x USB 2.0, 4 x COM, 2 x SATA III, 1 x Mini

PCIe slot (full-size), 1 x M.2 (B-key)

 Configurable watchdog timer and digital I/O, mSATA, EuP/ErP

 Wide temperature supported by IB811F-I50 and IB811F-I30

General Information

IB811F Series User’s Manual

3

1

1.3 Packing List

Your IB811F package should include the items listed below. If any of the items below is missing, contact the distributor or dealer from whom you purchased the product.

 IB811F SBC x 1

 Disk x 1

(including chipset drivers and flash memory utility)

 This User’s Manual x 1

1.4 Optional Accessories

IBASE provides optional accessories as follows. Please contact us or your dealer if you need any.

 Cable Kit (IB76A)

(including: SATA cable (SATA-53) x 1 Power cable (PW87) x 1 COM ports cable (PK1H) x 1 USB cable (USB29) x 1

 Heatsink for IB811F-I50 / IB811F-I30 (HSIB811-A)

 Heatsink for IB811F-420 / IB811F-335 (HSIB811-B)

 Audio cable (Audio-18)

4

IB811F Series User’s Manual

1.5 Specifications

Product Name

IB811F-I50

IB811F-I30

IB811F-420

IB811F-335 Form Factor

3.5” disk-size SBC

System

Operating System

 Windows 10 Enterprise (64-bit)

 Windows 10 IoT Core (64-bit)

 Linux Ubuntu

CPU Type

Intel® Atom™ QC x7 / E3950

Intel® Atom™ DC x5 / E3930

Intel® Pentium® QC N4200

Intel® Celeron® DC N3350

CPU Speed

1.6 ~ 2.0 GHz

1.3 ~ 1.8 GHz

1.1 ~ 2.5 GHz

1.1 ~ 2.4 GHz

Cache

2 MB

Chipset

Integrated

Memory

2 x DDR3L-1600/1866 SO-DIMM, expandable up to 8 GB (Non-ECC)

* DDR3L-1600 is for IB811F-335 only.

Storage

1 x mSATA SSD

Graphics

Intel® SoC integrated Gen. 9

Network

2 x Intel® I210IT PCIe Gigabit Ethernet

2 x Intel® I210AT PCIe Gigabit Ethernet

Super I/O

Fintek F81846AD-I

Audio Codec & Controller

Intel® SoC built-in HD audio controller

Realtek ALC283QHD codec with speaker amplifier

Power Requirement

9 ~ 36V DC-In ( jumper-selectable ATX / AT power mode)

Watchdog Timer

Yes (256 segments, 0, 1, 2…255 sec / min)

BIOS

AMI BIOS

H/W Monitor

Yes

General Information

IB811F Series User’s Manual

5

1

Product Name

IB811F-I50

IB811F-I30

IB811F-420

IB811F-335

Smart Control

 EuP/ErP

 Power failure detection by a jumper connector

 LVDS brightness control

Dimensions

102.22 x 147.01 mm (4.02” x 5.8”)

RoHS

Yes

Certification

CE, FCC Class B, LVD

I/O Ports

Display

 1 x HDMI (1.4b), 3840 x 2160 at 30 Hz

 1 x DisplayPort (1.2), 4096 x 2160 at 60 Hz

 1 x eDP / 24-bit dual channel LVDS

eDP: 4096 x 2160 at 60 Hz

LVDS: 1920 x 1200 at 60 Hz

LAN

2 x RJ45 GbE LAN

USB

 4 x USB 3.0: I/O coastline connectors

 2 x USB 2.0: via an on-board pin headers

Serial

4 x COM ports:

 COM1: RS-232/422/485 (I/O coastline RJ10

connector, jumper-less selection)

 COM2, COM3, COM4: RS-232 only (via on-board

box-headers)

SATA

2 x SATA III

Audio

On-board audio connector for Line-In, Line-Out, and Mic-In

Digital IO

4-In & 4-Out

Expansion Slots

 1 x Mini PCIe slot (full-size) with USB and mSATA

 1 x M.2 (B key) 3042 Slot with PCIe (x1), USB and

SATA

6

IB811F Series User’s Manual

Product Name

IB811F-I50

IB811F-I30

IB811F-420

IB811F-335

Environment

Temperature

 Operation: -40 ~ 85 °C

(-40 ~ 185 °F)

 Storage: -40 ~ 110 °C

(-40 ~ 230 °F)

 Operation: 0 ~ 60 °C

(32 ~ 140 °F)

 Storage: -40 ~ 110 °C

(-40 ~ 230 °F)

Relative Humidity

0 ~ 90 %, non-condensing at 60 °C

All specifications are subject to change without prior notice.

General Information

IB811F Series User’s Manual

7

1

1.6 Block Diagram

8

IB811F Series User’s Manual

1.7 Overview

Top View

Bottom View

Photo of IB811F-420

＊The photos above are for reference only. Some minor components may

differ.

General Information

IB811F Series User’s Manual

9

1

I/O View

No.

Name

No.

Name

1

COM1 (RJ10) Port

4

LAN Port

2

DisplayPort

5

USB 3.0 Port

3

HDMI Port

10

IB811F Series User’s Manual

1.8 Dimensions

0

5

13.45

13.30

41.78

97.23

102.22

18.4

37.39

58.92

70.36

85.92

111.04

128.26

142.01

147.01

16.34

11

Chapter 2 Hardware Configuration

This section provides information on jumper settings and connectors on the IB811F in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. The topics covered are:

 Essential installations before you begin:

CPU and the memory

 Jumper and connector locations

 Jumper settings and information of connectors

12

IB811F Series User’s Manual

2.1 Essential Installations Before You Begin

Follow the instructions below to install the memory.

2.1.1 Installing the Memory

The IB811F board supports two DDR3L memory sockets for a maximum total memory of 8 GB. To install the modules, locate the memory slot on the board and perform the following steps:

1. Align the key of the memory module with that on the memory slot and insert the module slantwise.

2. Gently push the module in an upright position until the clips of the slot close to hold the module in place when the module touches the bottom of the slot.

To remove the module, press the clips outwards with both hands, and the module will pop-up.

Hardware Configuration

IB811F Series User’s Manual

13

2

2.2 Setting the Jumpers

Set up and configure your IB811F by using jumpers for various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your use.

2.2.1 How to Set Jumpers

Jumpers are short-length conductors consisting of several metal pins with a non-conductive base mounted on the circuit board. Jumper caps are used to have the functions and features enabled or disabled. If a jumper has 3 pins, you can connect either PIN1 to PIN2 or PIN2 to PIN3 by shorting.

Pin# 1

2

3

A 3-pin jumper

A jumper cap

Refer to the illustration below to set jumpers.

Pin closed

Oblique view

Schematic illustration in the manual

Open

1 2 3

1-2

1 2 3

2-3

1 2 3

When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On.

When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off.

14

IB811F Series User’s Manual

2.3 Jumper & Connector Locations

J8

J5

JP2

JP4

JP3 J1

J3

J6

BAT1

J10

J4

J7

J21

JP6

JP5

JP7

J16

J17

J20

J12

J13

CN3

CN2

J11

JP1

J2

20474

1 717273

2

203

1

2 747172

73

204

203

1

1 30

1

12

1920

21920

1 7

8

1 2

11 12

1

2

9 10

1

9 10

10

2

2 1

J19

J15

JP8

CN1

1

CN6 CN5

CN4

CN9

J14

J18

CN8

CN7

BZ1

2

1

10

9

1

2 1

10 9

1

SIO

Intel®Atom™ QC/DC Intel® Pentium® QC Intel® Celeron® DC

Board diagram of IB811F

Hardware Configuration

IB811F Series User’s Manual

15

2

2.4 Jumpers Quick Reference

Function

Jumper Name

Page

LCD Panel Brightness Selection

JP1

15

LVDS Planel Power Selection

JP2

16

eDP Panel Power Selection

JP3

16

eDP / LVDS Panel Seelction

JP4

17

ATX / AT Power Selection

JP5

17

CMOS Data Clearance

JP6

18

ME Register Clearance

JP7

18

Factory Use Only

JP8

- -

2.4.1 LVDS Panel Brightness Selection (JP1)

1

Function

Pin closed

Illustration

3.3V

(default)

1-2

1

5V

2-3

1

16

IB811F Series User’s Manual

2.4.2 LVDS Panel Power Selection (JP2)

1

Function

Pin closed

Illustration

3.3V

(default)

1-2

1

5V

2-3

1

2.4.3 eDP Panel Power Selection (JP3)

1

Function

Pin closed

Illustration

3.3V

(default)

1-2

1

5V

2-3

1

Hardware Configuration

IB811F Series User’s Manual

17

2

2.4.4 eDP / LVDS Panel Selection (JP4)

1

Function

Pin closed

Illustration

eDP

1-2

1

LVDS

(default)

2-3

1

2.4.5 ATX / AT Power Selection (JP5)

1

Function

Pin closed

Illustration

ATX

(default)

1-2

1

AT

2-3

1

18

IB811F Series User’s Manual

2.4.6 CMOS Data Clearance (JP6)

1

Function

Pin closed

Illustration

Normal

(default)

1-2

1

Clear CMOS

2-3

1

2.4.7 ME Register Clearance (JP7)

1

Function

Pin closed

Illustration

Normal

(default)

1-2

1

Clear ME

2-3

1

Hardware Configuration

IB811F Series User’s Manual

19

2

2.5 Connectors Quick Reference

Function

Connector Name

Page

eDP Connector

CN1

20

SATA III Connector

CN2 (shared with M.2 B-key)

CN3 (shared with mSATA)

21 LAN Ports

CN4

21

USB 3.0 Ports

CN5, CN6

21

Console COM1 (RJ10) RS-232/422/485 Port

CN7

22 DisplayPort

CN8

23

HDMI Port

CN9

23

LCD Backlight Connector

J2

23

LVDS Connector

J1, J3

24

Audio Connector

J4

25

DDR3L SO-DIMM Slot

J5, J8

25

USB 2.0 Connector

J6

26

Amplifier Connector

J7

26

SATA HDD Power Connector

J10

27

Mini PCIe / mSATA Slot

J11

27

COM2 / COM3 / COM4 RS-232 Port

J16, J17, J12

28 M.2 (B key) 3042 Slot

J14

28

Front Panel Connector

J13

29

Digital I/O Connector

J18

30

DC Power Input Connector

J19

30

Factory Use Only

J15, J20, J21

- -

20

IB811F Series User’s Manual

2.5.1 eDP Connector (CN1)

1 30

Assignment

1

NC

16

Ground

2

BL_Power

17

NC 3 BL_Power

18

Panel_VDD

4

BL_Power

19

Panel_VDD

5

BL_Power

20

Ground

6

NC

21

AUX_N

7

NC

22

AUX_P

8

BRIGHTNESS

23

Ground

9

Bklt_en

24

TX0_P

10

Ground

25

TX0_N

11

Ground

26

Ground

12

Ground

27

TX1_P

13

Ground

28

TX1_N

14

HPD

29

Ground

15

Ground

30

NC

Hardware Configuration

IB811F Series User’s Manual

21

2

2.5.2 SATA III Connector (CN2, CN3)

CN2: shared with M.2 B-key

CN3: shared with mSATA

2.5.3 LAN Ports (CN4)

2.5.4 USB 3.0 Ports (CN5, CN6)

22

IB811F Series User’s Manual

2.5.5 Console COM1 (RJ10) RS-232/422/485 Port (CN7)

101

COM1 port is jumper-less and configurable in BIOS.

Assignment

1

DSR, Data set ready

6

DCD, Data carrier detect

2

Ground

7

DTR, Data terminal ready

3

Ground

8

CTS, Clear to send

4

TX, Transmit

9

RTS, Request to send

5

RX, Receive

10

RI, Ring Indicator

Assignment

RS-232

RS-422

RS-485

1

DSR

RX-

NC 2 Ground

Ground

3

Ground

4

TX

RX+

NC 5 RX

TX+

Data+

6

DCD

TX-

Data-

7

DTR

NC

NC 8 CTS

NC

NC 9 RTS

NC

10

RI

NC

Hardware Configuration

IB811F Series User’s Manual

23

2

2.5.6 DisplayPort (CN8)

2.5.7 HDMI Port (CN9)

2.5.8 LCD Backlight Connector (J2)

1

Assignment

1

+12V

3

Brightness Control

2

Backlight Enable

4

Ground

24

IB811F Series User’s Manual

2.5.9 LVDS Connector (J1, J3)

J3: 1st channel

20 19

2 1

J1: 2nd channel

1 2

19

20

Assignment

1

TX0P

2

TX0N

3

Ground

4

Ground

5

TX1P

6

TX1N

7

Ground

8

Ground

9

TX2P

10

TX2N

11

Ground

12

Ground

13

CLKP

14

CLKN

15

Ground

16

Ground

17

TX3P

18

TX3N

19

VDD

20

VDD

Hardware Configuration

IB811F Series User’s Manual

25

2

2.5.10 Audio Connector (J4)

12

2

11

1

Assignment

1

Lineout_L

2

Lineout_R

3

JD_FRONT

4

Ground

5

LINEIN_L

6

Linein_R

7

JD_LINEIN

8

Ground

9

MIC_L

10

MIC-R

11

JD_MIC1

12

Ground

2.5.11 DDR3L SO-DIMM Slot (J5, J8)

26

IB811F Series User’s Manual

2.5.12 USB 2.0 Connector (J6)

2

1 7

8

Assignment

1

VCC

2

Ground

3

D0-

4

D1+

5

D0+

6

D1-

7

Ground

8

VCC

2.5.13 Amplifier Connector (J7)

1

Assignment

1

OUTL+

3

OUTR-

2

OUTL-

4

OUTR+

Hardware Configuration

IB811F Series User’s Manual

27

2

2.5.14 SATA HDD Power Connector (J10)

1

Assignment

1

+5V

3

Ground

2

Ground

4

+12V

2.5.15 Mini PCIe / mSATA Slot (J11)

28

IB811F Series User’s Manual

2.5.16 COM2 / COM3 / COM4 RS-232 Port (J16, J17, J12)

J17 J16 J12

10

2

9

1

Assignment

1

DCD, Data carrier detect

2

RXD, Receive data

3

TXD, Transmit data

4

DTR, Data terminal ready

5

Ground

6

DSR, Data set ready

7

RTS, Request to send

8

CTS, Clear to send

9

RI, Ring indicator

10

Not Used

2.5.17 M.2 (B key) 3042 Slot (J14)

Hardware Configuration

IB811F Series User’s Manual

29

2

2.5.18 Front Panel Connector (J13)

1

2

8

7

Assignment

1

Ground

2

PWR_BTN

3

3.3V

4

HDD Active

5

Ground

6

Reset

7

+5V

8

Ground

J13 is utilized for system indicators to provide light indication of the computer activities and switches to change the computer status. It provides interfaces for the following functions.

 ATX Power ON Switch (Pins 1 and 2)

The 2 pins makes an “ATX Power Supply On/Off Switch” for the system

that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will power off the system.

 Hard Disk Drive LED Connector (Pins 3 and 4)

This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed.

 Reset Switch (Pins 5 and 6)

The reset switch allows you to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header.

 Power LED: Pins 7 and 8

This connector connects to the system power LED on control panel. This LED will light when the system turns on.

30

IB811F Series User’s Manual

2.5.19 Digital I/O Connector (J18)

9

1

10

2

Assignment

1

Ground

2

VCC

3

OUT3

4

OUT1

5

OUT2

6

OUT0

7

IN3

8

IN1

9

IN2

10

IN0

2.5.20 DC Power Input Connector (J19)

1

Assignment

1

+9V ~ +36V

2

Ground

31

Chapter 3 Drivers Installation

This chapter introduces installation of the following drivers:

 Intel® Chipset Software Installation Utility

 VGA Driver

 HD Audio Driver

 Intel® Trusted Execution Engine Installation

 LAN Driver

32

IB811F Series User’s Manual

3.1 Introduction

This section describes the installation procedures for software and drivers. The software and drivers are included with the motherboard. If you find anything missing, please contact the distributor where you made the purchase. The contents of this section include the following:

Note: After installing your Windows operating system, you must install the

Intel® Chipset Software Installation Utility first before proceeding with the drivers installation.

Driver Installation

IB811F Series User’s Manual

33

3

3.2 Intel® Chipset Software Installation Utility

The Intel® Chipset drivers should be installed first before the software drivers to install INF files for Plug & Play function for Intel chipset components. Follow the instructions below to complete the installation.

1. Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane.

2. Click Intel(R) Chipset Software Installation Utility.

34

IB811F Series User’s Manual

3. When the Welcome screen to the Intel® Chipset Device Software

appears, click Next to continue.

4. Click Yes to accept the software license agreement and proceed with

the installation process.

5. On the Readme File Information screen, click Install for installation.

6. The driver has been completely installed. You are suggested to restart the computer for changes to take effect.

Driver Installation

IB811F Series User’s Manual

35

3

3.3 VGA Driver Installation

1. Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane.

2. Click Intel(R) Apollolake Graphics Driver.

36

IB811F Series User’s Manual

3. When the Welcome screen appears, click Next to continue.

4. Click Yes to accept the license agreement and click Next until the

installation starts.

5. The driver has been completely installed. You are suggested to restart the computer for changes to take effect.

Driver Installation

IB811F Series User’s Manual

37

3

3.4 HD Audio Driver Installation

1. Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane.

2. Click Realtek High Definition Audio Driver.

38

IB811F Series User’s Manual

3. On the Welcome screen of the InstallShield Wizard, click Next for

installation.

4. Click Next until the installation starts.

5. The driver has been completely installed. You are suggested to restart the computer for changes to take effect.

Driver Installation

IB811F Series User’s Manual

39

3

3.5 Intel® Trusted Execution Engine Drivers

1. Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane.

2. Click Intel(R) TXE Drivers.

40

IB811F Series User’s Manual

3. When the Welcome screen appears, click Next.

4. Accept the license agreement and click Next.

5. Click Next for installation.

6. As the driver has been sccessfully installed, you are suggested to restart the computer for changes to take effect.

Driver Installation

IB811F Series User’s Manual

41

3

3.6 Intel® Serial IO Drivers

1. Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane.

2. Click Intel(R) Serial IO Drivers.

42

IB811F Series User’s Manual

3. When the Welcome screen to the InstallShield Wizard appears, click

Next.

4. Accept the license agreement and click Next.

5. After reading the Readme File Information, click Next for installation.

6. As the driver has been sccessfully installed, you are suggested to restart the computer for changes to take effect.

Driver Installation

IB811F Series User’s Manual

43

3

3.7 LAN Driver Installation

1. Click LAN Card on the left pane and then Intel LAN Controller Drivers

on the right pane.

2. Click Intel(R) I21x Gigabit Network Drivers..

44

IB811F Series User’s Manual

3. When the Welcome screen appears, click Next.

4. Accept the license agreement and click Next.

5. On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue.

6. The wizard is ready for installation. Click Install.

7. As the installation is complete, you are suggested to restart the computer for changes to take effect.

45

Chapter 4 BIOS Setup

This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows:

 Main Settings

 Advanced Settings

 Chipset Settings

 Boot Settings

 Security Settings

 Save & Exit

46

IB811F Series User’s Manual

4.1 Introduction

The BIOS (Basic Input/Output System) installed in the ROM of your computer system supports Intel® processors. The BIOS provides critical low-level support for standard devices such as disk drives, serial ports and parallel ports. It also provides password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.

4.2 BIOS Setup

The BIOS provides a Setup utility program for specifying the system configurations and settings. The BIOS ROM of the system stores the Setup utility. When you turn on the computer, the BIOS is immediately activated. Press the <Del> key immediately allows you to enter the Setup utility. If you are a little bit late pressing the <Del> key, POST (Power On Self Test) will continue with its test routines, thus preventing you from invoking the Setup.

If you still need to enter Setup, restart the system by pressing the ”Reset” button or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys.

You can also restart by turning the system Off and back On again.

The following message will appear on the screen:

Press <DEL> to Enter Setup

In general, press the arrow keys to highlight items, <Enter> to select, the <PgUp> and <PgDn> keys to change entries, <F1> for help, and <Esc> to quit.

BIOS Setup

IB811F Series User’s Manual

47

4

When you enter the BIOS Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices.

Warning: It is strongly recommended that you avoid making any changes to

the chipset defaults.

These defaults have been carefully chosen by both AMI and your

system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases.

48

IB811F Series User’s Manual

4.3 Main Settings

BIOS Setting

Description

System Date

Sets the date. Use the <Tab> key to switch between the data elements.

System Time

Set the time. Use the <Tab> key to switch between the data elements.

BIOS Setup

IB811F Series User’s Manual

49

4

4.4 Advanced Settings

This section allows you to configure, improve your system and allows you to set up some system features according to your preference.

50

IB811F Series User’s Manual

4.4.1 ACPI Computing

BIOS Setting

Description

Enable Hibernation

Enables / Disables the system ability to hibernate (OS/S4 Sleep State). This option may be not effective with some OS.

ACPI Sleep State

Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed.

BIOS Setup

IB811F Series User’s Manual

51

4

4.4.2 LVDS (eDP/DP) Configuration

BIOS Setting

Description

LVDS (eDP/DP) Support

Enables / Disables LVDS (eDP/DP)

Panel Color Depth

Selects a panel color depth as 18 or 24 (VESA or JEIDA) bit.

LVDS Channel Type

Sets the LVDS channel type as single or dual channel.

Panel Type

Selects a resolution that fits your panel.

Options: 800 x 600 / 1024 x 768 / 1280 x 1024 / 1366 x 768 / 1440 x 900 / 1600 x 900 / 1920 x 1080

LVDS Backlight Level Control

Selects from Level 1 to Level 8 for the LVDS backlight.

52

IB811F Series User’s Manual

4.4.3 F81866 Super IO Configuration

BIOS Setting

Description

Standby Power on S5

Enables / Disables to provide the standby power for devices.

Options: All Enable / Enable Ethernet for WOL / All Disable

Serial Ports Configuration

Sets parameters of serial ports.

Enables / Disables the serial port and select an optimal setting for the Super IO device.

BIOS Setup

IB811F Series User’s Manual

53

4

4.4.3.1. Serial Port 1 Configuration

BIOS Setting

Description

Serial Port

Enables / Disables the serial port.

Change Settings

Selects an optimal settings for Super IO device.

Options:

 Auto  IO = 3F8h; IRQ = 4  IO = 3F8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12  IO = 2F8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12  IO = 3E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12  IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12

Device Mode

Changes the serial port mode to:

 RS232  RS485 TX Low Active  RS485 with Termination TX Low Active  RS422  RS422 with Termination

54

IB811F Series User’s Manual

4.4.4 Fintek Super IO Hardware Monitor

BIOS Setting

Description

Temperatures / Voltages

These fields are the parameters of the hardware monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status.

CPU Shutdown Temperature

Sets a threshold of temperature to shut down if CPU goes overheated.

Options: Disabled / 70 °C / 75 °C / 80 °C / 85 °C / 90 °C / 95 °C

BIOS Setup

IB811F Series User’s Manual

55

4

4.4.5 M.2 Setup

BIOS Setting

Description

M.2 Select

Selects the M.2 interface as SATA or PCIe.

56

IB811F Series User’s Manual

4.4.6 CPU Configuration

BIOS Setting

Description

Socket 0 CPU Information

Displays the socket specific CPU information.

CPU Power Management

Allows you to enable / disable Turbo Mode.

Active Processor Cores

Enables / Disables the cores in the processor package.

Monitor Mwait

Enables / Disables Monitor Mwait.

BIOS Setup

IB811F Series User’s Manual

57

4

4.4.7 AMI Graphic Output Protocol Policy

BIOS Setting

Description

Output Select

Outputs through HDMI interface.

58

IB811F Series User’s Manual

4.4.8 Network Stack Configuration

BIOS Setting

Description

Network Stack

Enables / Disables UEFI Network Stack.

IPv4 PXE Support

Enables / Disables IPv4 PXE Boot Support.

If disabled, Ipv4 PXE boot option will not be created.

IPv4 HTTP Support

Enables / Disables IPv4 HTTP Boot Support.

If disabled, Ipv4 HTTP boot option will not be created.

IPv6 PXE Support

Enables / Disables IPv6 PXE Boot Support.

If disabled, Ipv4 PXE boot option will not be created.

IPv6 HTTP Support

Enables / Disables IPv6 HTTP Boot Support.

If disabled, Ipv4 HTTP boot option will not be created.

PXE boot wait time

Assigns a period of time to press ESC key to abort the PXE boot.

Media detect count

Assigns a number of times to check the presence of media.

BIOS Setup

IB811F Series User’s Manual

59

4

4.4.9 CMS Configuration

BIOS Setting

Description

CSM Support

Enables / Disables CSM support.

GateA20 Active

 Upon Request disables GA20 when using

BIOS services.

 Always cannot disable GA20, but is useful

when any RT code is executed above 1 MB.

INT19 Trap Response

Sets how BIOS reacts on INT19 trap by Option ROM.

 Immediate executes the trap right away.

 Postponed executes the trap during legacy

boot.

Boot option filter

Controls the priority of Legacy and UEFI ROMs.

Storage

Controls the execution of UEFI and Legacy Storage OpROM.

Video

Controls the execution of UEFI and Legacy Video OpROM.

Other PCI devices

Determines OpROM execution policy for devices other than network, storage or video.

60

IB811F Series User’s Manual

4.4.10 USB Configuration

BIOS Setting

Description

Legacy USB Support

 Enabled enables Legacy USB support.

 Auto disables legacy support if there is no

USB device connected.

 Disabled keeps USB devices available only

for EFI applications.

XHCI Hand-off

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.

USB Mass Storage Driver Support

Enables / Disables the support for USB mass storage driver.

USB Transfer time-out

The time-out value (1 / 5 10 / 20 secs) for Control, Bulk, and Interrupt transfers.

Device reset time-out

Gives seconds (10 / 20 / 30 / 40 secs) to delay execution of Start Unit command to USB mass storage device.

Device power-up delay

The maximum time the device will take before it properly reports itself to the Host Controller.

Auto uses default value for a Root port it is 100ms. But for a Hub port, the delay is taken from Hub descriptor.

BIOS Setup

IB811F Series User’s Manual

61

4

4.5 Chipset Settings

4.5.1 North Bridge

BIOS Setting

Description

Max TOLUD

Sets a maximum value of TOLUD.

Options: 2 / 2.25 / 2.5 / 2.75 / 3 GB

62

IB811F Series User’s Manual

4.5.2 South Cluster Configuration

4.5.2.1. HD Audio Configuration

BIOS Setup

IB811F Series User’s Manual

63

4

4.5.2.2. PCI Express Configuration

BIOS Setting

Description

PCI Express Root Port 1 ~ 6

Accesses the control of the PCI Express Root Port.

64

IB811F Series User’s Manual

BIOS Setting

Description

PCI Express Root Port

Enables/ Disables the PCIe root port.

Auto: To disable unused root port automatically for the most optimum power savings.

ASPM

Sets the PCIe active state power management.

Options: Disable / L0s / L1 / L0SL1 / Auto

L1 Substates

Sets PCIe L1 substates.

Options: Disables / L1.1 / L1.2 / L1.1 & L1.2

PME SCI

Enables / Disables PME SCI.

PCIe Speed

Configures the PCIe speed.

BIOS Setup

IB811F Series User’s Manual

65

4

4.5.2.3. SATA Drivers

BIOS Setting

Description

Chipset SATA

Enables / Disables the Chipset SATA Controller.

The Chipset SATA Controller supports the 2 black internal SATA ports (up to 3Gb/s supported per port).

SATA Mode Selection

Determines how SATA controller(s) operate.

66

IB811F Series User’s Manual

4.5.2.4. USB Configuration

BIOS Setting

Description

XHCI Pre-Boot Driver

Enables / Disables the support for XHCI Pre-Boot Driver.

XHCI Mode

Enables / Disables XHCI mode. If disabled, XHCI controller would be disabled, and none of the USB devices are detectable or usable when systen is booted up in OS.

Do NOT disable it unless for debug purpose.

USB VBUS

VBUS should be ON in HOST mode. It should be OFF in OTG device mode.

USB HSIC1 Support

Enables / Disables USB HSIC1.

USB SSIC1 Support

Enables / Disables USB SSIC1.

USB Port Disable Override

Selectively enables / disables the corresponding USB port from reporting a device connection to the controller.

XDCI Support

Enables / Disables XDCI.

XHCI Disable Compliance Mode

FALSE makes the XHCI Link Compliance Mode not disabled.

TRUE disables the XHCI Link Compliance Mode.

BIOS Setup

IB811F Series User’s Manual

67

4

4.6 Security Settings

BIOS Setting

Description

Setup Administrator Password

Sets an administrator password for the setup utility.

User Password

Sets a user password.

68

IB811F Series User’s Manual

4.7 Boot Settings

BIOS Setting

Description

Setup Prompt Timeout

Number of seconds to wait for setup activation key.

65535 (0xFFFF) means indefinite waiting.

Bootup NumLock State

Selects the keyboard NumLock state. Quiet Boot

Enables / Disables Quiet Boot option.

New Boot Option Policy

Controls the placement of newly detected UEFI boot options.

Options: Default, Place First, Place Last

Boot mode select

Selects a Boot mode, Legacy / UEFI / Dual.

Boot Option Priorities

Sets the system boot order priorities for hard disk, CD/DVD, USB, Network.

BIOS Setup

IB811F Series User’s Manual

69

4

4.8 Save & Exit Settings

BIOS Setting

Description

Save Changes and Exit

Exits system setup after saving the changes.

Discard Changes and Exit

Exits system setup without saving any changes.

Save Changes and Reset

Resets the system after saving the changes.

Discard Changes and Reset

Resets system setup without saving any changes.

Save Changes

Saves changes done so far to any of the setup options.

Discard Changes

Discards changes done so far to any of the setup options.

Restore Defaults

Restores / Loads defaults values for all the setup options.

Save as User Defaults

Saves the changes done so far as User Defaults.

Restore User Defaults

Restores the user defaults to all the setup options.

70

Appendix

This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration.

Appendix

IB811F Series User’s Manual

71

A. I/O Port Address Map

Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.

Address

Device Description

0x00000A00-0x00000A0F

Motherboard resources

0x00000A10-0x00000A1F

Motherboard resources

0x00000A20-0x00000A2F

Motherboard resources

0x0000002E-0x0000002F

Motherboard resources

0x0000004E-0x0000004F

Motherboard resources

0x00000061-0x00000061

Motherboard resources

0x00000063-0x00000063

Motherboard resources

0x00000065-0x00000065

Motherboard resources

0x00000067-0x00000067

Motherboard resources

0x00000070-0x00000070

Motherboard resources

0x00000070-0x00000070

System CMOS/real time clock

0x00000080-0x0000008F

Motherboard resources

0x00000092-0x00000092

Motherboard resources

0x000000B2-0x000000B3

Motherboard resources

0x00000680-0x0000069F

Motherboard resources

0x00000400-0x0000047F

Motherboard resources

0x00000500-0x000005FE

Motherboard resources

0x00000600-0x0000061F

Motherboard resources

0x0000164E-0x0000164F

Motherboard resources

0x0000F040-0x0000F05F

Intel(R) Celeron(R)/Pentium(R) Processor SMBUS - 5AD4

0x0000D000-0x0000DFFF

Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port 5AD9

72

IB811F Series User’s Manual

Address

Device Description

0x000003F8-0x000003FF

Communications Port (COM1)

0x000002F8-0x000002FF

Communications Port (COM2)

0x000003E8-0x000003EF

Communications Port (COM3)

0x000002E8-0x000002EF

Communications Port (COM4)

0x0000E000-0x0000EFFF

Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port 5AD8

0x00000000-0x0000006F

PCI Express Root Complex

0x00000078-0x00000CF7

PCI Express Root Complex

0x00000D00-0x0000FFFF

PCI Express Root Complex

0x00000020-0x00000021