IB100
TI AM3517 ARM CortexTM-A8
Embedded BOARD
USER’S MANUAL
Version 1.0
ii
IB100 User’s Manual
Acknowledgments
TI is a registered trademark of Texas Instruments.
All other product names or trademarks are properties of their
respective owners.
IB100 User’s Manual iii
Table of Contents
Introduction ....................................................... 1
Product Description ............................................................. 1
Checklist .............................................................................. 3
IB100 Specifications ........................................................... 4
Board Dimensions ............................................................... 6
Installations ....................................................... 9
Setting the Jumpers ........................................................... 10
Connectors on IB100 MRS ............................................... 16
iv
IB100 User’s Manual
This page is intentionally left blank.
INTRODUCTION
IB100 MRS User’s Manual 1
Introduction
Product Description
The IB100 embedded board is based on the TI AM3517 ARM
processor .TI AM3517 is a high-performance ARM Cortex-A8 with
speeds up to 600 MHz. The device offers 3D graphics acceleration while
also supporting numerous peripherals, including DDR2 and USB OTG
PHY that are well suited for industrial applications.
The following subsystems are part of the device:
• Mi croprocessor unit (MPU) s ubsystem bas ed on the ARM Corte x-A8
processor
• POWER VR SGX™ Graphics Accel erator Subsystem for 3D graphics
acceleration to support display and gaming effects
• Display subsystem with several features for multiple concurrent image
manipulation, and a programmable interface supporting a wide
variety of displays. .
• High performance interconnects provide high-bandwidth data
transfers
for multiple initiators to the internal and external memory controllers
and to on-chip peripherals. The device also offers a comprehensive
clock-management scheme.
INTRODUCTION
2
IB100 User’s Manual
IB100 FEATURES:
• TI AM3517 600MHz ARM Cortex-A8 microprocessor
• 256 MB DDR2 RAM
• 512MB NAND flash
• 1 x 18 Bit LCD connector
• 1x COM port connector
• 1 x Mini-PCIe (x1) slot (w/ USB support)
• 10/100 Based-T Ethernet (RJ-45) connector
• 12V DC-in power connector
• 1 x SD card slot
• 1 x USB OTG
• 1 x USB host
• LAN PoE support (option)
• Resistive touch connector
INTRODUCTION
IB100 MRS User’s Manual 3
Checklist
Your IB100 package should include the items listed below.
•
The IB100 Embedded board
•
This User’s Manual
INTRODUCTION
4
IB100 User’s Manual
IB100 Specifications
Mainboard
IB100-MRS
MPU Type
Operating
Frequency
TI AM3517:
65nm Bulk, 491-NFBGA,
600MHz (ARM CortexTM-A8 Core) 700mW TDP
(Est.)
Cache
Instruction cache: 16KB
Data cache: 16KB
L2 cache: 256KB
RAM
DDR2-667 1.8V
Onboard 256MB (64x16 x2)
C0241604000101000P/C0211304000370000P
Storage
NAND 256MB onboard (SLC flash 16bits)
SD slot support up to 2GB
Video
POWERVR SGX™ Graphics Accelerator
Subsystem for 3D
3D / OpenGLES – Transportation 1.1 and 2.0,
OpenVG1.
LAN
10/100 Based-T Ethernet
USB
USB - 2xHost (TUSP1211), 1xOTG
Power Control
TPS65023
PoE
TPS23757 PoE (PD) 12W
LCD Panel
Ampire AM-800600C3TMQW-TC0H
LCD Size: 8”
Resolution: 800 x 600
Contract Ratio: 500/1
Viewing Angle: 140/120
Brightness: 200nit
Touch Panel
Touch controller (TSC2004)
4 wired-resistive
Build on LCD Panel
Audio
Speaker & Mic
Edge I/O
• 10/100 LAN x1 (RJ45) (PoE supported)
• USB x 1 (USB Host. A-Type)
• USB OTG x 1 (mini USB B type)
• COM1 RS-232 x 1 for (RJ45 connector)
• LEDs light bar x 1 (2xGPIO pin control
Red and Green/Daughter Board) (LED
x12)
• SD slot x 1
• 12V DC-IN Jack with lock x 1
INTRODUCTION
IB100 MRS User’s Manual 5
Headers &
Expansion
Slots
Headers:
• TFT LCD Connector x 1 (STARCONN
089H40 or equivalent)
• GPIO x 8 (8pin, pitch 2.0 with 3.3V)
• COM (RS232) x 2 (pitch
2.0,COM2/COM3 debug port)
• Audio pin Header x2 (Mic x1 /Speaker x1)
• FPC connector for Touch x1
(CSF-0591-4P1T)
Slots:
• Half-Mini PCIe(x1) slot [USB] 26.8mm x
30 mm
Power
12V DC-IN or PoE
Mounting
VESA 75x75
Wall mount
Software
Support
Android
Linux
WinCE
Environment
0℃-45℃
INTRODUCTION
6
IB100 User’s Manual
[
Board Dimensions
Top Side
INTRODUCTION
IB100 MRS User’s Manual 7
Bottom Side
INSTALLATIONS
8
IB100 User’s Manual
This page is intentionally left blank.
INSTALLATIONS
IB100 MRS User’s Manual 9
Installations
This section provides information on how to use the jumpers and
connectors on the IB100 in order to set up a workable system. The topi cs
covered are:
Setting the Jumpers .................................................................... 10
Connectors on IB100 MRS ........................................................ 16
INSTALLATIONS
10
IB100 User’s Manual
Setting the Jumpers
Jumpers are used on IB100 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB100 and their respective functions.
Jumper Locations on IB100 ................................................................. 11
Jumper Locations on IB100 ................................................................. 11
J13: COM1 RS232 (RJ45) PIN8 /+5V/+3V Power Setting................ 13
J13: COM1 RS232 (RJ45) PIN3 /+5V/+3V Power Setting................ 13
J14: CN6 ID Pin Control (factory use only) ........................................ 14
S1 (sw1,sw2,sw3,sw4,sw5,sw6): System Boot Configuration
S1 (sw8): DVI Signal Output Control ................................................. 15
D8,D9,D10,D11,D12,D13,D14,D15,D16,D17,D18,D19: ................... 15
INSTALLATIONS
IB100 MRS User’s Manual 11
Jumper Locations on IB100
Top Side
INSTALLATIONS
12
IB100 User’s Manual
Bottom Side
INSTALLATIONS
IB100 MRS User’s Manual 13
J13: COM1 RS232 (RJ45) PIN8 /+5V/+3V Power Setting
J13 Setting Function
Pin 2-4
Short/Closed
COM1 PORT PIN 8
+5V
Pin 4-6
Short/Closed
COM1 PORT PIN 8
+3V
Pin 8-10
Short/Closed
COM1 PORT PIN 8
COM2_TX
Note: Pin 8 maximum output current is 0.5A
Default setting is Pin 2-4 Open, Pin 6-8 Open, Pin 8-10 Open.
J13: COM1 RS232 (RJ45) PIN3 /+5V/+3V Power Setting
J13 Setting Function
Pin 1-3
Short/Closed
COM1 PORT PIN 3
+5V
Pin 3-5
Short/Closed
COM1 PORT PIN 3
+3V
Pin 7-9
Short/Closed
COM1 PORT PIN 3
COM2_RX
Note: Pin 3 maximum output current is 0.5A.
Default setting is Pin 1-3 Open, Pin 5-7 Open, and Pin 7-9 Open
INSTALLATIONS
14
IB100 User’s Manual
J14: CN6 ID Pin Control (Factory use only)
J14 DVI Signal Output
Pin 1-2 Short/Closed CN6 USB used as host mode
Note: Default is Pin 1-2 open.
S1 (sw1,sw2,sw3,sw4,sw5,sw6): System Boot Configuration
S1
(sw1 .. sw6)
First Second Third Fourth
000100
USB SD
NAND
flash
100100 USB COM3
SD
111110
USB
COM 3
SD
NAND
flash
Note:
1: Switch On
0: Switch Off
Default setting is 111110
(sw1=1,sw2=1,sw3=1,sw4=1,sw5=1,sw6=0)
INSTALLATIONS
IB100 MRS User’s Manual 15
S1 (sw8): DVI Signal Output Control
S1 (sw8) Function
0(Off) Disable DVI Signal output
1(On) Enable DVI Signal output
Note:
Default setting is 1 (On).
D8,D9,D10,D11,D12,D13,D14,D15,D16,D17,D18,D19:
Double colors LED indicator
Pin # Description
U4. P07
Low: red color indicator light
High: red color indicator dark
U4. P06
Low: green color indicator light
High: green color indicator dark
Note: D8,D9, ..D19 are double color LED indicator, which have
red and green colors. ALL of them are parallel connected
together.
U4 is TCA6416PAW IC; The IC connects with AM3517 CPU via
I2C2 port.
INSTALLATIONS
16
IB100 User’s Manual
Connectors on IB100 MRS
Connector Locations on IB100 ............................................................ 17
CN2: SD Card Connector .................................................................... 18
COM1 Port: RJ45 10 Pin Connector ................................................... 18
COM2 Port: COM2 RS232 Connector ................................................ 18
COM3 Port: COM3 RS232 Connector, Debug Port Connector .......... 19
LVDS1: LVDS Display Connector ..................................................... 19
CN1: LCD 18 Bit Parallel Signal Conne ctor ....................................... 20
J3: LCD 24 Bit Parallel Signal Connector (Factory use only) ............. 21
CN3: Resistive Touch Panel Connector .............................................. 21
CN4: 10/100Mb LAN (PoE supported) .............................................. 22
CN8: LED Backlight Control Connector ............................................. 22
CN9: I2C3 Connector .......................................................................... 22
CN11: I2C2 Connector ........................................................................ 22
CN10: SPI1 Connector ........................................................................ 23
J2: ARM JTAG Debug Port (Factory use only) ................................ 23
J9: Resistive Touch Connector (Factory use only) .............................. 23
J17: RS232 Connector (Factory use only) ........................................... 23
JMIC1: Mic Connector ........................................................................ 23
J4: Speaker Right Out Connector ........................................................ 23
J5: Speaker Left Out Connector ........................................................... 23
J1: Digital I/O 4 In/4 Out Connector ................................................... 24
SW1: Push Button for Hardware Reset ............................................... 24
J6: S-Video Connector ......................................................................... 24
BAT1: CR2032 3V LITHIUM Battery Socket .................................... 24
CN5: 12V Power Connector ................................................................ 24
JUSB1: USB2.0 Type A Connector ................................................... 25
J11: USB2.0 Connector ....................................................................... 25
J12: USB2.0 Connector ....................................................................... 25
CN6: Mini USB OTG Connector ........................................................ 25
J8: Line-out Phone-Jack Connector ..................................................... 25
J7: DVI Connector ............................................................................... 26
JMINI1: Mini PCIE Connector ............................................................ 27
CN12: 5V Connector ........................................................................... 27
INSTALLATIONS
IB100 MRS User’s Manual 17
Connector Locations on IB100
b
b
INSTALLATIONS
18
IB100 User’s Manual
CN2: SD Card Connector
COM1 Port: RJ45 10 Pin Connector
Pin #
Signal Name
1
COM3 RXD, Receive data
(Same signal as COM3 Port Pin 1)
2
COM1 RTS, Request to send
3
VDD1
4
COM1 TXD, Transmit data
5
GND, ground
6
GND, ground
7
COM1 RXD, Receive data
8
VDD2
9
COM1 CTS, Clear to send
10
COM3 TXD, Transmit data
(Same signal as COM3 Port Pin 2)
Note: Please refer to J13 setting for Pin3 and Pin8.
COM2 Port: COM2 RS232 Connector
Pin #
Signal Name
1
COM2 RTS, Request to send
2
COM2 TXD, Transmit data
3
COM2 RXD, Receive data
4
COM2 CTS, Clear to send
5
GND, ground
6
NC
INSTALLATIONS
IB100 MRS User’s Manual 19
COM3 Port: COM3 RS232 Connector, Debug Port Connector
(Factory use only)
Pin #
Signal Name
1
COM3 RXD, Receive data
2
COM3 TXD, Transmit data
3
GND, ground
4
NC
LVDS1: LVDS Display Connector
Pin #
Signal Name
1
+3.3V
2
+3.3V
3
NC
4
NC
5
TX0-
6
TX0+
7
GND
8
TX1-
9
TX1+
10
GND
11
TX2-
12
TX2+
13
GND
14
TXC-
15
TXC+
16
GND
17
+5V or +12V
18
+5V or +12V
19
GND
20
BACKLIGHT ADJ
Note: Pin 17and Pin18 default setting voltage are +5V.
INSTALLATIONS
20
IB100 User’s Manual
CN1: LCD 18 Bit Parallel Signal Connector
Pin #
Signal Name
1
+5V
2
+5V
3
BACKLIGHT ADJ
4
GND
5
GND
6
+3.3V
7
+3.3V
8
MODE
9
DE
10
VSYNC
11
HSYNC
12
GND
13
B5(MSB)
14
B4
15
B3
16
GND
17
B2
18
B1
19
B0
20
GND
21
G5
22
G4
23
G3
24
GND
25
G2
26
G1
27
G0
28
GND
29
R5
30
R4
31
R3
32
GND
33
R2
34
R1
35
R0
36
GND
37
DCLK
38
GND
39
L/R
40
U/D
INSTALLATIONS
IB100 MRS User’s Manual 21
J3: LCD 24 Bit Parallel Signal Connector (Factory use only)
Pin #
Signal Name
Pin #
Signal Name
1
+5V
23
D16
2
+5V
24
D17
3
+3.3V
25
D18
4
+3.3V
26
D19
5
D0
27
D20
6
D1
28
D21
7
D2
29
D22
8
D3
30
D23
9
D4
31
GND
10
D5
32
DE
11
D6
33
VSYNC
12
D7
34
HSYNC
13
GND
35
DCLK
14
D8
36
BACKLIGHT ADJ
15
D9
37
BACKLIGHT ENABLE
16
D10
38
GND
17
D11
39
TOUCH YP
18
D12
40
TOUCH YM
19
D13
41
TOUCH XP
20
D14
42
TOUCH XM
21
D15
43
+12V
22
GND
44
+12V
CN3: Resistive Touch Panel Connector
Pin #
Signal Name
1
Touch YP
2
Touch XP
3
Touch YM
4
Touch XM
INSTALLATIONS
22
IB100 User’s Manual
CN4: 10/100Mb LAN (PoE supported)
This RJ45 LAN connector supports PoE function.
CN8: LED Backlight Control Connector
Pin #
Signal Name
1
+12V
2
BACKLIGHT ADJ
3
BACKLIGHT ENABLE
4
GND
Note: Pin 1 maximum output current is 0.5A
CN9: I2C3 Connector
Pin #
Signal Name
1
GND, ground
2
I2C3_SDA
3
I2C3_SCL
4
+3.3V
5
I2C3_INT1n
6
I2C3_RESETn
CN11: I2C2 Connector
Pin #
Signal Name
1
GND, ground
2
I2C2_SDA
3
I2C2_SCL
4
+3.3V
5
I2C2_INT1n
6
I2C2_RESETn
INSTALLATIONS
IB100 MRS User’s Manual 23
CN10: SPI1 Connector
Pin #
Signal Name
1
SPI1_CLK
2
SPI1_SIMO
3
SPI1_SOMI
4
SPI1_CS0
5
+3.3V
6
GND
J2: ARM JTAG Debug Port (Factory use only)
J9: Resistive Touch Connector (Factory use only)
J17: RS232 Connector (Factory use only)
JMIC1: Mic Connector
Pin #
Signal Name
1
GND
2
MIC Input
J4: Speaker Right Out Connector
Pin #
Signal Name
1
SPEAKER_RIGHT+
2
SPEAKER_RIGHT-
Note: The maximun output power is 2 W with 4 Ω speaker
or 1.4 W with 8 Ω speaker
J5: Speaker Left Out Connector
Pin #
Signal Name
1
SPEAKER_LEFT+
2
SPEAKER_LEFT-
Note: The maximun output power is 2 W with 4 Ω speaker
or 1.4 W with 8 Ω speaker
INSTALLATIONS
24
IB100 User’s Manual
J1: Digital I/O 4 In/4 Out Connector
Signal Name
Pin #
Pin #
Signal Name
GND
1 2 +3.3V
OUT3
3 4 OUT1
OUT2
5 6 OUT0
IN3
7 8 IN1
IN2
9
10
IN0
Note: All In/Out signals level are 3.3V level.
SW1: Push Button for Hardware Reset
J6: S-Video connector
BAT1: CR2032 3V LITHIUM Battery Socket
CN5: 12V Power Connector
This connector supplies the system board operating voltage
Pin 1
Pin 2
Pin #
Signal Name
1
+12V
2
GND
INSTALLATIONS
IB100 MRS User’s Manual 25
JUSB1: USB2.0 Type A Connector
Pin #
Signal Name
1
+5V
2
D- 3 D+
4
GND
J11: USB2.0 Connector
Pin #
Signal Name
1
+5V
2
D- 3 D+
4
GND
5
GND
J12: USB2.0 Connector
Pin #
Signal Name
1
+5V
2
D- 3 D+
4
GND
5
GND
CN6: Mini USB OTG Connector
Pin #
Signal Name
1
+5V
2
D- 3 D+ 4 ID
5
GND
J8: Line-out Phone-Jack Connector
INSTALLATIONS
26
IB100 User’s Manual
J7: DVI Connector
Pin #
Signal Name
1
TX2+
2
GND
3
TX2-
4
TX1+
5
GND
6
TX1-
7
TX0+
8
GND
9
TX0-
10
TXC+
11
GND
12
TXC-
13
NC
14
NC
15
NC
16
NC
17
GND
18
+5V
19
NC
INSTALLATIONS
IB100 MRS User’s Manual 27
JMINI1: Mini PCIE Connector
Signal Name
Pin #
Pin #
Signal Name
NC
1 2 +3.3V
NC
3 4 GND
NC
5 6 NC
NC
7 8 NC
GND
9
10
NC
NC
11
12
NC
NC
13
14
NC
GND
15
16
NC
NC
17
18
GND
NC
19
20
NC
GND
21
22
RESETn
NC
23
24
NC
NC
25
26
GND
GND
27
28
NC
GND
29
30
NC
NC
31
32
NC
NC
33
34
GND
NC
35
36
USB2.0 D-
GND
37
38
USB2.0 D+
GND
39
40
GND
NC
41
42
NC
GND
43
44
NC
NC
45
46
NC
NC
47
48
NC
NC
49
50
GND
NC
51
52
+3.3V
CN12: 5V Connector
Pin #
Signal Name
1
+5V
2
GND
INSTALLATIONS
28
IB100 User’s Manual
This page is intentionally left blank.
APPENDIX
IB100 MRS User’s Manual 29
Loading...