FWA8708-C
FWA8708-H
1U Rackmount
Network Appliance
User’s Manual
Version 1.0
(Dec. 2018)
ii
FWA8708-C / FWA8708-H User Manual
Copyright
© 2018 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
FWA8708-C / FWA8708-H User Manual
iii
Compliance
This product has passed CE tests for environmental specifications and limits. This
product is in accordance with the directives of the Union European (EU). If users
modify and/or install other devices in this equipment, the CE conformity declaration
may no longer apply.
This product has been tested and found to comply with the limits for a Class A
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
• Lead (Pb)
• Mercury (Hg)
• Cadmium (Cd)
• Hexavalent chromium (Cr6+)
• Polybrominated biphenyls (PBB)
• Polybrominated diphenyl ether (PBDE)
iv
FWA8708-C / FWA8708-H User Manual
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
• Lay the device horizontally on a stable and solid surface in case the device may
fall, causing serious damage.
• Slots and openings on the chassis are for ventilation. Do not block or cover these
openings. Make sure you leave plenty of space around the device for ventilation.
NEVER INSERT OBJECTS OF ANY KIND INTO THE VENTILATION
OPENINGS.
• Use this product in environments at ambient temperatures 0˚C ~ 40˚.
• DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20˚C OR ABOVE 70˚C. This
could damage the device. The device must be used in a controlled environment.
Care for your IBASE products:
• Before cleaning the device, turn it off and unplug all cables such as power in case
a small amount of electrical current may still flow.
• Use neutral cleaning agents or diluted alcohol to clean the device chassis with a
cloth. Then wipe the chassis with a dry cloth.
• Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots
from being clogged.
WARNING
Attention during use:
• Do not use this product near water.
• Do not spill water or any other liquids on your device.
• Do not place heavy objects on the top of the device.
• Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult your distributor or local
power company.
• Do not walk on the power cord or allow anything to rest on it.
• If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
• When handling processor chips or memory modules, avoid touching their pins or
gold fingers. Put modules or peripherals back into antistatic bags when they are
not in use or not installed in the chassis.
Avoid Disassembly
Do not disassemble, repair or make any modification to the device. Disassembly,
modification, or any attempt at repair could generate hazards and cause damage to
the device, even bodily injury or property damage, and will void any warranty.
FWA8708-C / FWA8708-H User Manual
v
CAUTION
Danger of explosion if internal lithium-ion battery is replaced by an incorrect type.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions. Under no
circumstances should the Lithium battery cell be shorted; otherwise the battery cell
may heat up or cause potential burn hazards.
Warranty Policy
• IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
• 3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, memory, HDD, power adapter, panel
and touchscreen.
＊ PRODUCTS, HOWEVER, THAT FAILS DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from your distributor or sales representative,
prepare the following information of your product and elaborate upon the
problem.
• Product model name
• Product serial number
• Detailed description of the problem
• The error messages in text or in screenshots if there is any
• The arrangement of the peripherals
• Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.
vi
FWA8708-C / FWA8708-H User Manual
Table of Contents
Compliance.................................................................................................... iii
Important Safety Information ....................................................................... iv
WARNING ...................................................................................................... iv
CAUTION ........................................................................................................ v
Warranty Policy .............................................................................................. v
Technical Support & Services ...................................................................... v
Chapter 1 General Information ................................................................ 1
1.1 Introduction ............................................................................................. 2
1.2 Features .................................................................................................. 3
1.3 Packing List ............................................................................................ 3
1.4 Optional Accessories .............................................................................. 4
1.5 Specifications .......................................................................................... 4
1.6 Overview ................................................................................................. 7
1.7 Dimensions ............................................................................................. 9
Chapter 2 Hardware Configuration ....................................................... 10
2.1 Installation / Replacement ..................................................................... 11
2.1.1 Network Module Installation / Removal ................................ ... 12
2.1.2 HDD Installation / Removal ..................................................... 12
2.1.3 Memory Installation / Replacement ......................................... 14
2.1.4 IPMI Module Installation / Replacement .................................. 15
2.1.5 Fan Module Installation / Removal .......................................... 16
2.1.6 Redundant Power Supply Unit Installation / Replacement ...... 16
2.2 Pinout for Console Port ......................................................................... 16
2.3 Setting the Jumper ................................................................................ 17
2.4 Jumper & Connector Locations on Motherboard ................................... 18
2.5 Jumper Quick Reference ...................................................................... 20
2.5.1 AT & ATX Mode (JP2) .......................................................... 20
2.5.2 PEG Configuration (JBAT1, JBAT2) ..................................... 21
2.5.3 Clearing CMOS Data (JBAT3) ............................................. 22
2.5.4 Clearing ME Register (JBAT4) ............................................. 23
2.6 Connectors Quick Reference ................................................................ 24
2.6.1 External Power Switch Connector (J2) ................................. 25
FWA8708-C / FWA8708-H User Manual
vii
2.6.2 USB 2.0 Connector (J15) ..................................................... 26
2.6.3 PM Bus Port (J20) ................................................................ 27
2.6.4 System Function Connector (JP3) ........................................ 28
2.6.5 Digital I/O Connector (JP4) .................................................. 29
2.6.6 External SATA Power Connector (CN1, CN4, CN5) ............. 30
2.6.7 LCM Connector (CN7) ......................................................... 31
2.6.8 ATX Power Connector (J1, J18) ........................................... 32
2.6.9 Fan Connector (FAN_CPU1, FAN1, FAN2, FAN3, FAN4) .... 33
Chapter 3 BIOS Setup ............................................................................ 34
3.1 Introduction ........................................................................................... 35
3.2 BIOS Setup ........................................................................................... 35
3.3 Main Settings ........................................................................................ 36
3.4 Advanced Settings ................................................................................ 37
3.4.1 CPU Configuration .................................................................. 37
3.4.2 Trusted Computing ................................................................. 38
3.4.3 SATA Configuration ................................................................ 39
3.4.4 Smart Settings ........................................................................ 39
3.4.5 NCT5523D Super I/O Configuration ....................................... 40
3.4.6 NCT7904D HW Monitor .......................................................... 43
3.4.7 LAN Bypass Configuration ...................................................... 44
3.4.8 Serial Port Console Redirection .............................................. 45
3.4.9 USB Configuration .................................................................. 47
3.5 Security Settings ................................................................................... 48
3.6 Boot Settings......................................................................................... 49
3.7 Save & Exit Settings.............................................................................. 50
Appendix ...................................................................................................... 51
A. I/O Port Address Map ............................................................................ 52
B. Interrupt Request Lines (IRQ) ............................................................... 54
C. Digital I/O Sample Code ........................................................................ 57
D. Watchdog Timer Configuration .............................................................. 62
1
Chapter 1
General Information
The information provided in this chapter includes:
• Features
• Packing List
• Optional Accessories
• Specifications
• Overview
• Dimensions
2
FWA8708-C / FWA8708-H User Manual
1.1 Introduction
FWA8708 series are specifically designed for the network security and
management market. There are plenty of applications adopting network
security or network management as listed below.
• FWA8708-C
• FWA8708-H
Network Security Applications:
• Firewall
• Unified Threat Management (UTM)
• Virtual Private Network (VPN)
• Proxy Server
• Caching Server
Network Management Applications:
• Load balancing
• Quality of Service
• Remote Access Service
The FWA networking appliance product line covers the spectrum from offering
platforms designed for:
• SOHO
• SMB
• Enterprise
Each product is designed to address the distinctive requirements of its
respective market segment from cost effective entry-level solutions to high
throughput and performance-bound systems for the enterprise level.
General Information
FWA8708-C / FWA8708-H User Manual
3
1
1.2 Features
• 8
th
Gen. Intel® Xeon® / Core™ i7/i5/i3 processor with up to 6 cores plus
C246 or H310 PCH
• 6 x RJ45 GbE + 2x SFP GbE on board (SFP for FWA8708-C only)
• 4 or 2 x DDR4 DIMM, expandable up to 64 GB (ECC or non-ECC)
• Optional IPMI 2.0 module (for FWA8708-C only)
• Optional NIC slot (for FWA8708-C only)
• 1 x Mini-PCIe and 1 x M.2 M2280 expansion slots
1.3 Packing List
Your product package should include the items listed below. If any of the
items below is missing, contact the distributor or the dealer from whom you
purchased the product.
Models with a single PSU:
• FWA8708 x 1
• 250W Full Range ATX Power Supply x 1
• Power Cord (180 cm) x 1
• Rack Mount Bracket x 2
Models with 1+1 redundant PSU:
• FWA8708 x 1
• 300W 1+1 Redundant Power Supply Unit x 1
• Power Cord (180 cm) x 2
• Rack Mount Bracket x 2
4
FWA8708-C / FWA8708-H User Manual
1.4 Optional Accessories
IBASE provide optional accessories as follows. Please contact us or your
dealer if you need any.
• Console Cable (160 cm, PK1-51)
• IPMI Module (IDN100)
• VGA Cable (40 cm, VGA21A)
• NIC Modules:
IBN-R420BN (4 x RJ45 GbE, Non-Bypass)
IBN-R420B (4 x RJ45 GbE, 2 Bypass Segment)
IBN-R840N (8 x RJ45 GbE, Non-Bypass)
IBN-R840 (8 x RJ45 GbE, 4 Bypass Segment)
IBN-S400 (4 x GbE SFP, Non-Bypass)
IBN-S800 (8 x GbE SFP, Non-Bypass)
IBN-P400D (2 x 10GbE SFP+, Non-Bypass)
IBN-P400Q (4 x 10GbE SFP+, Non-Bypass)
IBN-S420D (2 x GbE SFP, 1 Bypass Segment)
IBN-S420Q (4 x GbE SFP, 2 Bypass Segment)
IBN-P420D (2 x 10GbE SFP+, 1 Bypass Segment)
IBN-P420Q (4 x 10GbE SFP+, 2 Bypass Segment)
IBN-F200 (2 x 25GbE SFP+, Non-Bypass)
1.5 Specifications
Product Name
FWA8708-C
FWA8708-H
System
Motherboard
MBN805C
MBN805H
Operating
System
• Windows 10 (64-bit)
• Linux Ubuntu 16.04
CPU
8th Gen. Intel® Xeon
®
/ Core™
i7/i5/i3 LGA1151
8th Gen. Intel® Core™ i7/i5/i3
LGA1151
Chipset
Intel® C246 PCH
Intel® H310 PCH
Memory
4 x DDR4 DIMM up to 2666
MHz; max. 64 GB UDIMM
(ECC or non-ECC)
2 x DDR4 DIMM up to 2666
MHz; max. 32 GB UDIMM
(ECC or non-ECC)
Network
• 6 x Intel
®
I210AT GbE
controller
• 2 x Intel
®
I210IS GbE
controller
6 x Intel® I211AT GbE
controller
General Information
FWA8708-C / FWA8708-H User Manual
5
1
Product Name
FWA8708-C
FWA8708-H
Storage
• 1 x 3.5” or 2 x 2.5” SATA
drive bay (Optional)
• 1 x M.2 M2280 slot with
PCIe (x4) & SATA signal
1 x 3.5” or 2 x 2.5” SATA drive
bay (Optional)
IPMI
IPMI module compliant with
IPMI 2.0 (Optional)
N/A
Super I/O
Nuvoton NCT5523D
Bypass
2 x segment, LAN3 & LAN4, LAN5 & LAN6
Power Supply
• Single PSU: Full range 250W ATX power supply unit
• 1+1 RPSU: 300W 1+1 redundant power supply unit
Power
Requirement
100 ~ 240V AC
BIOS
AMI BIOS
Watchdog
Watchdog Timer 256 segments, 0, 1, 2…255 sec/min
Chassis
Steel with textured black paint
Dimensions
(W x H x D)
438 x 44 x 422 mm (17.24” x 1.73” x 16.61”)
Weight
9 kg (19.84 lb)
Certificate
CE / FCC Class A
Front I/O Ports
LCM
1 x LCM 16x2 dots with 4 keypads
LED
3 x LEDs for power, HDD, status
Console
1 x Console port
Management
Port (MGMT)
1 x MGMT (LAN1 shared with IPMI NC-SI port)
Ethernet Port
• Up to 6 x RJ45 GbE + 2 x
SFP LAN ports
• 1 x network module slot for
an IBN card, with up to 16
GbE ports in total (Optional)
Up to 6 x RJ45 GbE LAN ports
GPIO
1 x user self-defined GPIO button
USB
2 x USB 3.0
IBN Card
IBN module tray (Optional)
N/A
Rear I/O Ports
AC Inlet
• Single PSU: 1 x 100 ~ 240V AC Inlet, full range 250W ATX
power supply
• 1+1 RPSU: 2 x 100 ~ 240V AC Inlet, with 2 hot-swappable
300W power supply modules
6
FWA8708-C / FWA8708-H User Manual
Product Name
FWA8708-C
FWA8708-H
Display
1 x VGA port (reserved and optional) via the onboard pin header
Fan
3 x system fans
Expansion
• 2 x PCIe (x8) slot
• 1 x Mini-PCIe slot with PCIe
& SATA
• 1 x M.2 M2280 with PCIe
(x4) & SATA
• 1 x PCIe (x8) slot
• 1 x Mini-PCIe slot with
SATA only
Environment
Temperature
• Operating: 0 ~ 40 °C (32 ~ 104 °F)
• Storage: -20~ 70 °C (-4 ~ 158 °F)
Relative
Humidity
5 ~ 90% at 45 °C (non-condensing)
Vibration
Protection
• Operating: 0.25 Grms / 3 ~ 500 Hz (Z-axis)
• Non-operating: 1.0 Grms / 3 ~ 500Hz (Z-axis)
Shock
Protection
Sawtooth wave 40G (X/Y/Z-axis)
All specifications are subject to change without prior notice.
General Information
FWA8708-C / FWA8708-H User Manual
7
1
1.6 Overview
Front View
• FWA8708-C
• FWA8708-H
No.
Name
No.
Name
1
LCM Display with 4 buttons
5
USB 3.0 Ports
2
Console Port
6
GbE LAN Ports
3
LED Indicators
(From top to bottom: Status,
HDD, Power)
7
Reserved Area for IBN module
(for FWA8708-C only)
4
User Self-Defined GPIO
Button
8
FWA8708-C / FWA8708-H User Manual
Rear View
• Single Power Supply Unit
• Redundant Power Supply Unit
No.
Name
No.
Name
1
PCIe (x8) Expansion Card Slot
4
Power Switch
2
VGA Port
(via an onboard pin-header or
via the optional IPMI module)
5
Single Power Supply Unit
3
System Fan Modules
6
Reduntant Power Supply
Oblique View
• FWA8708-C
• FWA8708-H
General Information
FWA8708-C / FWA8708-H User Manual
9
1
1.7 Dimensions
Unit: mm
10
Chapter 2
Hardware Configuration
The information provided in this chapter includes:
• Installation / Replacement
• Information and locations of connectors
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
11
2
2.1 Installation / Replacement
For the hot-swappable HDD or the IBN Network Interface Modules
installations, you can directly install without remove the device cover.
For the memory, M.2, PCIe expansion card or the optional IPMI module, you
need to remove 8 screws as shown below to pull out the lid.
Configuration inside:
Areas B allows for optional IBN modules, two 2.5” or one 3.5” HDD/SSD. Area
A allows for optional two 2.5” or one 3.5” HDD/SSD, or for expansion cards.
12
FWA8708-C / FWA8708-H User Manual
2.1.1 Network Module Installation / Removal
Note: IBN module is purchasable and applicable for FWA8708-C only.
Release two screws of a network module and pull it out carefully as shown
below for replacement and installation.
2.1.2 HDD Installation / Removal
After you remove the device cover, you can see the optional areas A and B as
shown below allowing for optional HDD/SSD and expansion cards installation.
If you need to install or replace an HDD/SDD, follow the instructions below for
installation.
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
13
2
1. Remove 4 screws to loose each 3.5” or 2.5” HDD/SSD tray from the
bottom of the device.
2. Unplug the SATA power and data cable. Remove 4 screws for each 3.5”
or 2.5” HDD/SSD to free up the HDD/SSD from the tray.
3.5” HDD/SSD:
2.5” HDD/SSD:
3. Take out the HDD and install a new one onto the tray. Fasten 4 screws
back for each HDD.
4. Secure the tray with HDD from the bottom of the device. Note the screw
holes for different sizes of HDD/SSD as ilustrated below.
14
FWA8708-C / FWA8708-H User Manual
2.1.3 Memory Installation / Replacement
If you need to install or replace a memory module, follow the instructions
below for installation after you remove the device cover.
1. Press the ejector tab of the memory slot down and outwards with your
fingertips.
2. Hold the memory module and align the key of the module with that on the
memory slot.
3. Gently push the module in an upright position until the ejector tabs of the
memory slot close to hold the module in place when the module touches
the bottom of the slot.
To remove the module, press the ejector tabs outwards with your fingertips to
eject the module.
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
15
2
2.1.4 IPMI Module Installation / Replacement
If you need to install an IPMI module, remove the system lid firstly and then
follow the instructions below.
Note: IPMI module is optionally purchasable and applicable for FWA8708-C
only.
1. Locate the IPMI slot and align the key of the module with that on the slot.
1. Insert the module slantwise and gently push the module straight down
until the clips of the slot close to hold the module in place when the
module touches the bottom of the slot.
.
To remove the module, press the clips outwards with your thumb and index
finger of both hands.
16
FWA8708-C / FWA8708-H User Manual
2.1.5 Fan Module Installation / Removal
If you need to install or replace a fan module, after removing the device cover,
release 4 screws for each fan module on the rear side of the device, take out
the fan, replace with a new one, and tighten these screws.
2.1.6 Redundant Power Supply Unit Installation / Replacement
If you need to install or replace a redundant power supply unit, push the latch
downwards, grasp the handle, pull the PSU out carefully and replace with a
new one.
2.2 Pinout for Console Port
➔
Pin
Signal Name
Pin
Signal Name
1
RTS
5
Ground
2
DTR
6
RXD
3
TXD
7
DSR
4
Ground
8
CTS
8 1
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
17
2
2.3 Setting the Jumper
Set up and configure your system by using jumpers for various settings and
features according to your needs and applications. Contact your supplier if
you have doubts about the best configuration for your use.
Jumpers are short-length conductors consisting of several metal pins with a
non-conductive base mounted on the circuit board. Jumper caps are used to
have the functions and features enabled or disabled. If a jumper has 3 pins,
you can connect either PIN1 to PIN2 or PIN2 to PIN3 by shorting.
Refer to the illustration below to set jumpers.
Pin closed
Oblique view
Schematic illustration in the manual
Open
1-2
2-3
When two pins of a jumper are encased in a jumper cap, this jumper is closed,
i.e. turned On.
When a jumper cap is removed from two jumper pins, this jumper is open, i.e.
turned Off.
18
FWA8708-C / FWA8708-H User Manual
2.4 Jumper & Connector Locations on Motherboard
Motherboard for FWA8708-C: MBN805C
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
19
2
Motherboard for FWA8708-H: MBN805H
20
FWA8708-C / FWA8708-H User Manual
2.5 Jumper Quick Reference
Function
Connector Name
Page
AT & ATX Mode Selection
JP2
20
PEG Configuration
JBAT1, JBAT2
21
Clearing CMOS Data
JBAT3
22
Clearing ME Register
JBAT4
23
Factory Use Only
JP1, JBMC1, JBMC2
--
Note: The following motherboard drawings in this section are illustrated by the
example of MBN805C.
2.5.1 AT & ATX Mode (JP2)
Function
Pin closed
Illustration
AT Mode (Default)
1-2
ATX Mode
2-3
1
1
1
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
21
2
2.5.2 PEG Configuration (JBAT1, JBAT2)
JBAT1
JBAT2
The PEG bifurcation is only configurable for FWA8708-C.
1 x PCIe (x16) is always used for FWA8708-H.
Function
Pin closed
Illustration
1 x PCIe (x16)
JBAT1: Open
JBAT2: Open
2 x PCIe (x8)
JBAT1: Close
JBAT2: Open
RSVD
JBAT1: Open
JBAT2: Close
PCIe (x8), PCIe (x4),
PCIe (x4)
(Default)
JBAT1: Close
JBAT2: Close
1
1
111
1
111
22
FWA8708-C / FWA8708-H User Manual
2.5.3 Clearing CMOS Data (JBAT3)
Function
Pin closed
Illustration
Normal (Default)
1-2
Clearing CMOS
2-3
1
1
1
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
23
2
2.5.4 Clearing ME Register (JBAT4)
Function
Pin closed
Illustration
Normal (Default)
1-2
Clearing ME Register
2-3
1
1
1
24
FWA8708-C / FWA8708-H User Manual
2.6 Connectors Quick Reference
Function
Connector Name
Page
External Power Switch Connector
J2
25
USB 2.0 Connector
J15
26
PM Bus Port
[1]
J20
27
System Function Connector
JP3
28
Digital I/O Connector
JP4
29
External SATA Power Connector
CN1, CN4, CN5
30
LCM Connector
CN7
31
ATX Power Connector
J1, J18
32
Fan Connector
FAN_CPU1, FAN1, FAN2,
FAN3, FAN4
33
Console & Double Stack USB 3.0
Connector
CN9
--
External VGA Connector
J3
--
USB 3.0 Port
J10
--
DDR4 UDIMM Slot
FWA8708-C: J4, J5, J6, J7
FWA8708-H: J5, J7
-IPMI Slot
[2]
J12
--
Mini-PCIe Slot
J16
--
M.2 M2280 Slot
[1]
J17
--
Fiber LAN Connector
[1]
CN8
--
GbE LAN Port
CN10, CN11, CN12,
CN13, CN14, CN15
--
SATA III Port
CN2, CN3, CN6
--
PCIe Gold Finger
Standard: PCIE2 (with x8
signal)
For IBN Card only: PCIE1
(with x8 / x4 / x4 signal
-Factory Use Only
J8, J11, J14, J19
--
[1]: Available only for FWA8708-C.
[2]: Optionally purchasable for FWA8708-C.
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
25
2
The following motherboard drawings in this section are illustrated by the
example of MBN805C.
2.6.1 External Power Switch Connector (J2)
Pin
Signal Name
Pin
Signal Name
1
ATX_PSON#_EN
2
Ground
1
26
FWA8708-C / FWA8708-H User Manual
2.6.2 USB 2.0 Connector (J15)
Pin
Signal Name
Pin
Signal Name
1
5VDUAL
2
5VDAUL
3
USB_PN8
4
USB_PN9
5
USB_PP8
6
USB_PP9
7
Ground
8
Ground
9
NC
10
NC
9
1
10
2
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
27
2
2.6.3 PM Bus Port (J20)
The PM Bus port J20 is only available for FWA8708-C.
Pin
Signal Name
Pin
Signal Name
1
SMB_PWR_5VDUAL_CLK
4
Ground
2
SMB_PWR_5VDUAL_DAT
5
VCC3_3
3
PL_SMBAlert
28
FWA8708-C / FWA8708-H User Manual
2.6.4 System Function Connector (JP3)
Pin
Signal Name
Pin
Signal Name
1
VCC5
2
Speaker
3
NC 4 NC 5 Ground
6
Ground
7
NC 8 VCC5
9
5VDUAL
10
BYPASSLED0-
11
5VDUAL
12
BYPASSLED1-
13
Ground
14
ATXPWR_BTN#
15
NC
16
NC
17
Ground
18
FRST_OUT
19
VCC3_3
20
-HDD_LED
2
20 19
1
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
29
2
2.6.5 Digital I/O Connector (JP4)
Pin
Signal Name
Pin
Signal Name
1
Ground
2
VCC5
3
INT0_SIOGP22
4
INT0_SIOGP25
5
INT0_SIOGP23
6
INT0_SIOGP26
7
INT0_SIOGP24
8
INT0_SIOGP27
1
2
8
7
30
FWA8708-C / FWA8708-H User Manual
2.6.6 External SATA Power Connector (CN1, CN4, CN5)
CN1:
CN4:
CN5:
Pin
Signal Name
Pin
Signal Name
1
VCC5
3
Ground
2
Ground
4
VCC12
1
1
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
31
2
2.6.7 LCM Connector (CN7)
(with RS-232 signal)
Pin
Signal Name
Pin
Signal Name
1
LCM_RD1
4
VCC5
2
LCM_TD1
5
NC 3 Ground
32
FWA8708-C / FWA8708-H User Manual
2.6.8 ATX Power Connector (J1, J18)
J1:
J18:
J1:
Pin
Assignment
Pin
Assignment
1
Ground
5
+12V
2
Ground
6
+12V
3
Ground
7
+12V
4
Ground
8
+12V
J18:
Pin
Assignment
Pin
Assignment
1
3.3V
13
3.3V
2
3.3V
14
-12V
3
Ground
15
Ground
4
+5V
16
PS-ON
5
Ground
17
Ground
6
+5V
18
Ground
7
Ground
19
Ground
8
Power good
20
-5V
9
5VSB
21
+5V
10
+12V
22
+5V
11
+12V
23
+5V
12
+3.3V
24
Ground
1
5
8
4
1 13
2412
Hardware Configuration
FWA8708-C / FWA8708-H User Manual
33
2
2.6.9 Fan Connector (FAN_CPU1, FAN1, FAN2, FAN3, FAN4)
FAN1:
FAN2:
FAN3:
FAN_CPU1:
FAN4:
CPU_FAN, FAN1, FAN2, FAN3:
Pin
Assigment
Pin
Assigment
1
Ground
3
FAN_TACH
2
VCC12
4
FAN_PWM
FAN4:
Pin
Assigment
Pin
Assigment
1
Ground
3
FAN_TACH
2
VCC12
1
1
34
Chapter 3
BIOS Setup
This chapter describes the different settings available in the AMI
BIOS that comes with the board. The topics covered in this chapter
are as follows:
• Main Settings
• Advanced Settings
• Chipset Settings
• Security Settings
• Boot Settings
• Save & Exit
BIOS Setup
FWA8708-C / FWA8708-H User Manual
35
3
3.1 Introduction
The BIOS (Basic Input/Output System) installed in the ROM of your computer
system supports Intel® processors. The BIOS provides critical low-level
support for standard devices such as disk drives, serial ports and parallel
ports. It also provides password protection as well as special support for
detailed fine-tuning of the chipset controlling the entire system.
3.2 BIOS Setup
The BIOS provides a Setup utility program for specifying the system
configurations and settings. The BIOS ROM of the system stores the Setup
utility. When you turn on the computer, the BIOS is immediately activated.
Press the <Del> key immediately allows you to enter the Setup utility. If you
are a little bit late pressing the <Del> key, POST (Power On Self Test) will
continue with its test routines, thus preventing you from invoking the Setup.
If you still need to enter Setup, restart the system by pressing the ”Reset”
button or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys.
You can also restart by turning the system Off and back On again.
The following message will appear on the screen:
Press <DEL> to Enter Setup
In general, press the arrow keys to highlight items, <Enter> to select, the
<PgUp> and <PgDn> keys to change entries, <F1> for help, and <Esc> to
quit.
When you enter the BIOS Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup functions
and exit choices.
Warning: It is strongly recommended that you avoid making any changes to
the chipset defaults.
These defaults have been carefully chosen by both AMI and your
system manufacturer to provide the absolute maximum
performance and reliability. Changing the defaults could make the
system unstable and crash in some cases.
36
FWA8708-C / FWA8708-H User Manual
3.3 Main Settings
BIOS Setting
Description
System Date
Sets the date. Use the <Tab> key to switch
between the data elements.
System Time
Set the time. Use the <Tab> key to switch
between the data elements.
BIOS Setup
FWA8708-C / FWA8708-H User Manual
37
3
3.4 Advanced Settings
This section allows you to configure, improve your system and allows you to
set up some system features according to your preference.
3.4.1 CPU Configuration
BIOS Setting
Description
Intel(R)
SpeedStep(tm)
Allows more than two frequency ranges to be
supported.
Turbo Mode
Enables / Disables processor Turbo Mode (requires
Intel Speed Step or Intel Speed Shift to be available
and enabled).
C states
Enables / Disables CPU power management. Allows
CPU to go to C states when it’s not 100% utilized.
38
FWA8708-C / FWA8708-H User Manual
3.4.2 Trusted Computing
BIOS Setting
Description
Security Device Support
Enables / Disables BIOS support for security
device. The operating system will not show the
security device. TCG EFI protocol and INT1A
interface will not be available.
SHA-1 PCR Bank
Enables / Disables SHA-1 PCR Bank.
SHA256 PCR Bank
Enables / Disables SHA256 PCR Bank.
Pending operation
Schedule an operation for the security device.
Note: Your computer will reboot during restart
in order to change the state of security device.
Options: None, TPM Clear
Platform Hierarchy
Enables / Disables Platform Hierarchy.
Storage Hierarchy
Enables / Disables Storage Hierarchy.
Endorsement Hierarchy
Enables / Disables Endorsement Hierarchy.
TPM 2.0 UEFI Spec
Version
Allows you to select the TCG2 spec version
support.
TCG_1_2: the compatible mode for Windows
10 & 8.
TCG_2: Support new TCG2 protocol and
event.
Physical Presence Spec
Selects a version of PPI spec version 1.2 or 1.3
to tell OS to support it.
Note: Some HCT tests might not support 1.3.
BIOS Setup
FWA8708-C / FWA8708-H User Manual
39
3
3.4.3 SATA Configuration
BIOS Setting
Description
SATA Controller(s)
Enables / Disables SATA device.
SATA Mode Selection
Determines how SATA controller(s) operate.
This PCH SKU doesn’t support RST feature.
Aggressive LPM Support
Enables PCH to aggressively enter link power
state.
Serial ATA Port 0/1/2/3
Enables / Disables a Serial ATA port.
3.4.4 Smart Settings
BIOS Setting
Description
Smart Self Test
Run Smart Self Test on all HDDs during POST.
40
FWA8708-C / FWA8708-H User Manual
3.4.5 NCT5523D Super I/O Configuration
BIOS Setting
Description
Serial Ports Configuration
Sets Parameters of Serial Ports.
You can enable / disable the serial port and
select an optimal settings for the Super IO
device.
Restore AC Power Loss
Select AC power state when power is reapplied after a power failure.
Options: Power Off, Power On, Last State
BIOS Setup
FWA8708-C / FWA8708-H User Manual
41
3
3.4.5.1. Serial Port 1 Configuration
BIOS Setting
Description
Serial Port
Sets parameters of Serial Ports (COM).
Change Settings
Selects an optimal settings for Super I/O device.
Options:
• Auto
• IO = 3F8h; IRQ = 4
• IO = 3F8h; IRQ = 3, 4, 5, 6, 7
• IO = 2F8h; IRQ = 3, 4, 5, 6, 7
• IO = 3E8h; IRQ = 3, 4, 5, 6, 7
• IO = 2E8h; IRQ = 3, 4, 5, 6, 7
42
FWA8708-C / FWA8708-H User Manual
3.4.5.2. Serial Port 2 Configuration
BIOS Setting
Description
Serial Port
Sets parameters of Serial Ports (COM).
Change Settings
Selects an optimal settings for Super I/O
device.
Options:
• Auto
• IO = 2F8h; IRQ = 3
• IO = 3F8h; IRQ = 3, 4, 5, 6, 7
• IO = 2F8h; IRQ = 3, 4, 5, 6, 7
• IO = 3E8h; IRQ = 3, 4, 5, 6, 7
• IO = 2E8h; IRQ = 3, 4, 5, 6, 7
BIOS Setup
FWA8708-C / FWA8708-H User Manual
43
3
3.4.6 NCT7904D HW Monitor
BIOS Setting
Description
Smart Fan Control
Disables or sets the smart fan control start up
temperature.
Options: Disabled, 40°C, 45°C, 50°C, 55°C,
60°C
ACPI Shutdown
Temperature
Options: Disabled, 70°C, 75°C, 80°C, 85°C, 90
°C, 95°C
Temperatures / Voltages
/ Fan Speed
These fields are the parameters of the
hardware monitoring function feature of the
motherboard. The values are read-only as
monitored by the system and showing the PC
health status
44
FWA8708-C / FWA8708-H User Manual
3.4.7 LAN Bypass Configuration
BIOS Setting
Description
Bypass Quick Setting
• Bypass Mode: All LAN ports with bypass
function in Bypass mode during power-off or
WDT initiates bypass. System will not
reboot.
• Normal Mode: All LAN ports in normal mode.
WDT monitor system hang & initiates a
reboot.
• Firewall Mode: All LAN ports in bypass until
OS has control ability to change LAN ports in
normal.
• Custom Define: All LAN ports can be
configured independently.
BIOS Setup
FWA8708-C / FWA8708-H User Manual
45
3
3.4.8 Serial Port Console Redirection
BIOS Setting
Description
Console Redirection
Enables / Disables Console Redirection.
Console Redirection
Settings
The settings specify how the host computer
and the remote computer (which the user is
using) will exchange data. Both computers
should have the same or compatible settings.
Sets parameters of Console Redirection.
46
FWA8708-C / FWA8708-H User Manual
3.4.8.1. Console Redirection Settings
BIOS Setting
Description
Terminal Type
Emulation of the following options:
ANSI: Extended ASCII charset.
VT100: ASCII charset.
VT100+: Extends VT100 to support color,
function keys, etc.
VT-UTF8: Uses UTF8 encoding to map Unicode.
Bits per second
Selects serial port transmission speed. The
speed must be matched on the other side. Long
or noisy lines may require lower speeds.
Options: 9600, 19200, 38400, 57600, 115200
Data Bits
Selects the data bits as 7 or 8.
Parity
A parity bit can be sent with the data bits to
detect some transmission errors.
Options: None, Even, Odd, Mark, Space
Stop Bits
Stop bits indicate the end of a serial data packet.
(A start bit indicates the beginning). The
standard setting is 1 stop bit.
Options: 1, 2
Flow Control
Flow control can prevent data loss from buffer
overflow. When sending data, if the receiving
buffers are full, a “stop” signal can be sent to
stop the data flow.
Options: None, Hardware RTS/CTS
BIOS Setup
FWA8708-C / FWA8708-H User Manual
47
3
BIOS Setting
Description
VT-UTF8 Combo Key
Support
Enables / Disables VT-UTF8 combination key
support for ANSI/VT100 terminals.
Recorder Mode
With this mode enabled only text will be sent.
This is to capture terminal data.
Resolution 100x31
Enables / Disables extended terminal resolution.
Putty KeyPad
Select FunctionKey and KeyPad on Putty.
Options: VT100, LINUX, XTERMR6, SCO,
ESCN, VT400
3.4.9 USB Configuration
BIOS Setting
Description
Legacy USB Support
Enables / Disables Legacy USB support.
• Auto disables legacy support if there is no
USB device connected.
• Disable keeps USB devices available only
for EFI applications.
XHCI Hand-off
This is a workaround for OSes without XHCI
hand-off support. The XHCI ownership change
should be claimed by XHCI driver.
USB Mass Storage Driver
Support
Enables / Disables USB mass storage driver
support.
48
FWA8708-C / FWA8708-H User Manual
3.5 Security Settings
BIOS Setting
Description
Administrator Password
Sets an administrator password for the setup
utility.
User Password
Sets a user password.
BIOS Setup
FWA8708-C / FWA8708-H User Manual
49
3
3.6 Boot Settings
BIOS Setting
Description
Setup Prompt Timeout
Number of seconds to wait for setup activation
key.
65535 (0xFFFF) means indefinite waiting.
Bootup NumLock State
Selects the keyboard NumLock state.
Quiet Boot
Enables / Disables Quiet Boot option.
Network
Controls the execution of UEFI and Legacy
Network OpROM.
Options: Do not launch, UEFI, Legacy
Boot Option Priorities
Sets the system boot order.
50
FWA8708-C / FWA8708-H User Manual
3.7 Save & Exit Settings
BIOS Setting
Description
Save Changes and Exit
Exits system setup after saving the changes.
Save Changes and Reset
Resets the system after saving the changes.
Discard Changes and
Reset
Resets system setup without saving any
changes.
Restore Defaults
Restores / Loads defaults values for all the
setup options.
51
Appendix
This section provides the mapping addresses of peripheral
devices and the sample code of watchdog timer configuration.
• I/O Port Address Map
• Interrupt Request Lines (IRQ)
• Digital I/O Sample Code
• Watchdog Timer Configuration
52
FWA8708-C / FWA8708-H User Manual
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port addresses
which also becomes the identity of the device. The following table lists the I/O
port addresses used.
Address
Device Description
0x00000A00-0x00000A0F
Motherboard resources
0x00000A10-0x00000A1F
Motherboard resources
0x00000A20-0x00000A2F
Motherboard resources
0x0000002E-0x0000002F
Motherboard resources
0x0000004E-0x0000004F
Motherboard resources
0x00000061-0x00000061
Motherboard resources
0x00000063-0x00000063
Motherboard resources
0x00000065-0x00000065
Motherboard resources
0x00000067-0x00000067
Motherboard resources
0x00000070-0x00000070
Motherboard resources
0x00000080-0x00000080
Motherboard resources
0x00000092-0x00000092
Motherboard resources
0x000000B2-0x000000B3
Motherboard resources
0x00000680-0x0000069F
Motherboard resources
0x0000164E-0x0000164F
Motherboard resources
0x00000020-0x00000021
Programmable interrupt controller
0x00000024-0x00000025
Programmable interrupt controller
0x00000028-0x00000029
Programmable interrupt controller
0x0000002C-0x0000002D
Programmable interrupt controller
0x00000030-0x00000031
Programmable interrupt controller
0x00000034-0x00000035
Programmable interrupt controller
0x00000038-0x00000039
Programmable interrupt controller
0x0000003C-0x0000003D
Programmable interrupt controller
0x000000A0-0x000000A1
Programmable interrupt controller
0x000000A4-0x000000A5
Programmable interrupt controller
0x000000A8-0x000000A9
Programmable interrupt controller
0x000000AC-0x000000AD
Programmable interrupt controller
Appendix
FWA8708-C / FWA8708-H User Manual
53
Address
Device Description
0x000000B0-0x000000B1
Programmable interrupt controller
0x000000B4-0x000000B5
Programmable interrupt controller
0x000000B8-0x000000B9
Programmable interrupt controller
0x000000BC-0x000000BD
Programmable interrupt controller
0x000004D0-0x000004D1
Programmable interrupt controller
0x00001854-0x00001857
Motherboard resources
0x00006000-0x00006FFF
Intel(R) PCI Express Root Port #7 - A33E
0x00004000-0x00004FFF
Intel(R) PCI Express Root Port #11 - A332
0x000003F8-0x000003FF
Communications Port (COM1)
0x000002F8-0x000002FF
Communications Port (COM2)
0x00001800-0x000018FE
Motherboard resources
0x000000F0-0x000000F0
Numeric data processor
0x00000000-0x00000CF7
PCI Express Root Complex
0x00000D00-0x0000FFFF
PCI Express Root Complex
0x00009090-0x00009097
Standard SATA AHCI Controller
0x00009080-0x00009083
Standard SATA AHCI Controller
0x00009060-0x0000907F
Standard SATA AHCI Controller
0x00007000-0x00007FFF
Intel(R) PCI Express Root Port #6 - A33D
0x00000040-0x00000043
System timer
0x00000050-0x00000053
System timer
0x00002000-0x000020FE
Motherboard resources
0x00009000-0x0000903F
Intel(R) UHD Graphics 630
0x000003B0-0x000003BB
Intel(R) UHD Graphics 630
0x000003C0-0x000003DF
Intel(R) UHD Graphics 630
0x00005000-0x00005FFF
Intel(R) PCI Express Root Port #8 - A33F
0x00003000-0x00003FFF
Intel(R) PCI Express Root Port #12 - A333
0x0000EFA0-0x0000EFBF
Intel(R) SMBus - A323
0x00008000-0x00008FFF
Intel(R) PCI Express Root Port #5 - A33C
54
FWA8708-C / FWA8708-H User Manual
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the service
required. The following table shows the IRQ used by the devices on board.
Level
Function
IRQ 9
Intel(R) Gaussian Mixture Model - 1911
IRQ 9
Intel(R) Thermal Subsystem - A379
IRQ 9
Intel(R) SMBus - A323
IRQ 4294967291
Intel(R) PCI Express Root Port #7 - A33E
IRQ 4294967289
Intel(R) PCI Express Root Port #11 - A332
IRQ 4294967277
Intel(R) USB 3.1 eXtensible Host Controller - 1.10
(Microsoft)
IRQ 4
Communications Port (COM1)
IRQ 3
Communications Port (COM2)
IRQ 13
Numeric data processor
IRQ 4294967287
Standard SATA AHCI Controller
IRQ 54 ~ IRQ 204
Microsoft ACPI-Compliant System
IRQ 256 ~ IRQ 511
Microsoft ACPI-Compliant System
IRQ 4294967292
Intel(R) PCI Express Root Port #6 - A33D
IRQ 4294967276
Intel(R) Management Engine Interface
IRQ 0
System timer
IRQ 4294967278
Intel(R) UHD Graphics 630
IRQ 4294967275
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967274
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967273
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967272
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967271
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967270
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967269
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967268
Intel(R) I211 Gigabit Network Connection #7
IRQ 4294967267
Intel(R) I211 Gigabit Network Connection #8
IRQ 4294967266
Intel(R) I211 Gigabit Network Connection #8
IRQ 4294967265
Intel(R) I211 Gigabit Network Connection #8
IRQ 4294967264
Intel(R) I211 Gigabit Network Connection #8
Appendix
FWA8708-C / FWA8708-H User Manual
55
Level
Function
IRQ 4294967263
Intel(R) I211 Gigabit Network Connection #8
IRQ 4294967262
Intel(R) I211 Gigabit Network Connection #8
IRQ 4294967261
Intel(R) I211 Gigabit Network Connection #8
IRQ 4294967260
Intel(R) I211 Gigabit Network Connection #8
IRQ 4294967259
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967258
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967257
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967256
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967255
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967254
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967253
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967252
Intel(R) I211 Gigabit Network Connection #11
IRQ 4294967251
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967250
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967249
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967248
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967247
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967246
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967245
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967244
Intel(R) I211 Gigabit Network Connection #12
IRQ 4294967243
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967242
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967241
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967240
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967239
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967238
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967237
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967236
Intel(R) I211 Gigabit Network Connection #9
IRQ 4294967286
Intel(R) I211 Gigabit Network Connection #10
IRQ 4294967285
Intel(R) I211 Gigabit Network Connection #10
IRQ 4294967284
Intel(R) I211 Gigabit Network Connection #10
56
FWA8708-C / FWA8708-H User Manual
Level
Function
IRQ 4294967283
Intel(R) I211 Gigabit Network Connection #10
IRQ 4294967282
Intel(R) I211 Gigabit Network Connection #10
IRQ 4294967281
Intel(R) I211 Gigabit Network Connection #10
IRQ 4294967280
Intel(R) I211 Gigabit Network Connection #10
IRQ 4294967279
Intel(R) I211 Gigabit Network Connection #10
IRQ 14
Intel(R) Serial IO GPIO Host Controller - 3450
IRQ 4294967290
Intel(R) PCI Express Root Port #8 - A33F
IRQ 4294967288
Intel(R) PCI Express Root Port #12 - A333
IRQ 4294967293
Intel(R) PCI Express Root Port #5 - A33C
IRQ 4294967294
Intel(R) PCIe Controller (x16) - 1901
Appendix
FWA8708-C / FWA8708-H User Manual
57
C. Digital I/O Sample Code
1. The file NCT5523D.H
//--------------------------------------------------------------------------// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A
PARTICULAR
// PURPOSE.
//--------------------------------------------------------------------------#ifndef __NCT5523D_H
#define __NCT5523D_H 1
//--------------------------------------------------------------------------#define NCT5523D_INDEX_PORT (NCT5523D_BASE)
#define NCT5523D_DATA_PORT (NCT5523D_BASE+1)
//--------------------------------------------------------------------------#define NCT5523D_REG_LD 0x07
//--------------------------------------------------------------------------#define NCT5523D_UNLOCK 0x87
#define NCT5523D_LOCK 0xAA
//--------------------------------------------------------------------------unsigned int Init_NCT5523D(void);
void Set_NCT5523D_LD( unsigned char);
void Set_NCT5523D_Reg( unsigned char, unsigned char);
unsigned char Get_NCT5523D_Reg( unsigned char);
//--------------------------------------------------------------------------#endif //__NCT5523D_H
58
FWA8708-C / FWA8708-H User Manual
2. The file MAIN.CPP
//--------------------------------------------------------------------------// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A
PARTICULAR
// PURPOSE.
//--------------------------------------------------------------------------#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "NCT5523D.H"
//--------------------------------------------------------------------------int main (void);
void Dio5Initial(void);
void Dio5SetOutput(unsigned char);
unsigned char Dio5GetInput(void);
void Dio5SetDirection(unsigned char);
unsigned char Dio5GetDirection(void);
//--------------------------------------------------------------------------int main (void)
{
char SIO;
SIO = Init_NCT5523D();
if (SIO == 0)
{
printf("Can not detect Nuvoton NCT5523D, program abort.\n");
return(1);
}
Dio5Initial();
//for GPIO20..27
Dio5SetDirection(0x0F); //GP20..23 = input, GP24..27=output
printf("Current DIO direction = 0x%X\n", Dio5GetDirection());
printf("Current DIO status = 0x%X\n", Dio5GetInput());
printf("Set DIO output to high\n");
Dio5SetOutput(0x0F);
printf("Set DIO output to low\n");
Dio5SetOutput(0x00);
return 0;
}
//---------------------------------------------------------------------------
Appendix
FWA8708-C / FWA8708-H User Manual
59
void Dio5Initial(void)
{
unsigned char ucBuf;
ucBuf = Get_NCT5523D_Reg(0x1C);
ucBuf &= ~0x02;
Set_NCT5523D_Reg(0x1C, ucBuf);
Set_NCT5523D_LD(0x07); //switch to logic device 7
//enable the GP2 group
ucBuf = Get_NCT5523D_Reg(0x30);
ucBuf |= 0x04;
Set_NCT5523D_Reg(0x30, ucBuf);
}
//--------------------------------------------------------------------------void Dio5SetOutput(unsigned char NewData)
{
Set_NCT5523D_LD(0x07); //switch to logic device 7
Set_NCT5523D_Reg(0xE1, NewData);
}
//--------------------------------------------------------------------------unsigned char Dio5GetInput(void)
{
unsigned char result;
Set_NCT5523D_LD(0x07); //switch to logic device 7
result = Get_NCT5523D_Reg(0xE1);
return (result);
}
//--------------------------------------------------------------------------void Dio5SetDirection(unsigned char NewData)
{
//NewData : 1 for input, 0 for output
Set_NCT5523D_LD(0x07); //switch to logic device 7
Set_NCT5523D_Reg(0xE8, NewData);
}
//--------------------------------------------------------------------------unsigned char Dio5GetDirection(void)
{
unsigned char result;
Set_NCT5523D_LD(0x07); //switch to logic device 7
result = Get_NCT5523D_Reg(0xE8);
return (result);
}
//---------------------------------------------------------------------------
60
FWA8708-C / FWA8708-H User Manual
3. The file NCT5523D.CPP
//--------------------------------------------------------------------------// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A
PARTICULAR
// PURPOSE.
//--------------------------------------------------------------------------#include "NCT5523D.H"
#include <dos.h>
//--------------------------------------------------------------------------unsigned int NCT5523D_BASE;
void Unlock_NCT5523D (void);
void Lock_NCT5523D (void);
//--------------------------------------------------------------------------unsigned int Init_NCT5523D(void)
{
unsigned int result;
unsigned char ucDid;
NCT5523D_BASE = 0x4E;
result = NCT5523D_BASE;
ucDid = Get_NCT5523D_Reg(0x20);
if (ucDid == 0xC4) //NCT5523D??
{ goto Init_Finish; }
NCT5523D_BASE = 0x2E;
result = NCT5523D_BASE;
ucDid = Get_NCT5523D_Reg(0x20);
if (ucDid == 0xC4) //NCT5523D??
{ goto Init_Finish; }
NCT5523D_BASE = 0x00;
result = NCT5523D_BASE;
Init_Finish:
return (result);
}
//--------------------------------------------------------------------------void Unlock_NCT5523D (void)
{
outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK);
outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK);
}
//--------------------------------------------------------------------------void Lock_NCT5523D (void)
{
outportb(NCT5523D_INDEX_PORT, NCT5523D_LOCK);
}
//---------------------------------------------------------------------------
Appendix
FWA8708-C / FWA8708-H User Manual
61
void Set_NCT5523D_LD( unsigned char LD)
{
Unlock_NCT5523D();
outportb(NCT5523D_INDEX_PORT, NCT5523D_REG_LD);
outportb(NCT5523D_DATA_PORT, LD);
Lock_NCT5523D();
}
//--------------------------------------------------------------------------void Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_NCT5523D();
outportb(NCT5523D_INDEX_PORT, REG);
outportb(NCT5523D_DATA_PORT, DATA);
Lock_NCT5523D();
}
//--------------------------------------------------------------------------unsigned char Get_NCT5523D_Reg(unsigned char REG)
{
unsigned char Result;
Unlock_NCT5523D();
outportb(NCT5523D_INDEX_PORT, REG);
Result = inportb(NCT5523D_DATA_PORT);
Lock_NCT5523D();
return Result;
}
//---------------------------------------------------------------------------
62
FWA8708-C / FWA8708-H User Manual
D. Watchdog Timer Configuration
The Watchdog Timer (WDT) is used to generate a variety of output signals
after a user programmable count. The WDT is suitable for the use in the
prevention of system lock-up, such as when software becomes trapped in a
deadlock. Under these sorts of circumstances, the timer will count to zero and
the selected outputs will be driven.
Under normal circumstance, you will need to restart the WDT at regular
intervals before the timer counts to zero.
1. Sample Code: The file NCT5523D.H
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A
PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#ifndef __NCT5523D_H
#define __NCT5523D_H 1
//--------------------------------------------------------------------------#define NCT5523D_INDEX_PORT (NCT5523D_BASE)
#define NCT5523D_DATA_PORT (NCT5523D_BASE+1)
//--------------------------------------------------------------------------#define NCT5523D_REG_LD 0x07
//--------------------------------------------------------------------------#define NCT5523D_UNLOCK 0x87
#define NCT5523D_LOCK 0xAA
//--------------------------------------------------------------------------unsigned int Init_NCT5523D(void);
void Set_NCT5523D_LD( unsigned char);
void Set_NCT5523D_Reg( unsigned char, unsigned char);
unsigned char Get_NCT5523D_Reg( unsigned char);
//--------------------------------------------------------------------------#endif //__NCT5523D_H
Appendix
FWA8708-C / FWA8708-H User Manual
63
2. Sample Code: The file MAIN.CPP
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A
PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "NCT5523D.H"
//--------------------------------------------------------------------------int main (void);
void WDTInitial(void);
void WDTEnable(unsigned char);
void WDTDisable(void);
//--------------------------------------------------------------------------int main (void)
{
char SIO;
SIO = Init_NCT5523D();
if (SIO == 0)
{
printf("Can not detect Nuvoton NCT5523D, program abort.\n");
return(1);
}
WDTInitial();
WDTEnable(10);
WDTDisable();
return 0;
}
//--------------------------------------------------------------------------void WDTInitial(void)
{
unsigned char bBuf;
Set_NCT5523D_LD(0x08); //switch to logic device 8
bBuf = Get_NCT5523D_Reg(0x30);
bBuf &= (~0x01);
Set_NCT5523D_Reg(0x30, bBuf); //Enable WDTO
}
//---------------------------------------------------------------------------
64
FWA8708-C / FWA8708-H User Manual
void WDTEnable(unsigned char NewInterval)
{
unsigned char bBuf;
Set_NCT5523D_LD(0x08); //switch to logic device 8
Set_NCT5523D_Reg(0x30, 0x01); //enable timer
bBuf = Get_NCT5523D_Reg(0xF0);
bBuf &= (~0x08);
Set_NCT5523D_Reg(0xF0, bBuf); //count mode is second
Set_NCT5523D_Reg(0xF1, NewInterval); //set timer
}
//--------------------------------------------------------------------------void WDTDisable(void)
{
Set_NCT5523D_LD(0x08); //switch to logic device 8
Set_NCT5523D_Reg(0xF1, 0x00); //clear watchdog timer
Set_NCT5523D_Reg(0x30, 0x00); //watchdog disabled
}
//---------------------------------------------------------------------------
Appendix
FWA8708-C / FWA8708-H User Manual
65
3. Sample Code: The file NCT5523D.CPP
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A
PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include "NCT5523D.H"
#include <dos.h>
//--------------------------------------------------------------------------unsigned int NCT5523D_BASE;
void Unlock_NCT5523D (void);
void Lock_NCT5523D (void);
//--------------------------------------------------------------------------unsigned int Init_NCT5523D(void)
{
unsigned int result;
unsigned char ucDid;
NCT5523D_BASE = 0x4E;
result = NCT5523D_BASE;
ucDid = Get_NCT5523D_Reg(0x20);
if (ucDid == 0xC4) //NCT5523D??
{ goto Init_Finish; }
NCT5523D_BASE = 0x2E;
result = NCT5523D_BASE;
ucDid = Get_NCT5523D_Reg(0x20);
if (ucDid == 0xC4) //NCT5523D??
{ goto Init_Finish; }
NCT5523D_BASE = 0x00;
result = NCT5523D_BASE;
Init_Finish:
return (result);
}
//--------------------------------------------------------------------------void Unlock_NCT5523D (void)
{
outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK);
outportb(NCT5523D_INDEX_PORT, NCT5523D_UNLOCK);
}
//---------------------------------------------------------------------------
66
FWA8708-C / FWA8708-H User Manual
void Lock_NCT5523D (void)
{
outportb(NCT5523D_INDEX_PORT, NCT5523D_LOCK);
}
//--------------------------------------------------------------------------void Set_NCT5523D_LD( unsigned char LD)
{
Unlock_NCT5523D();
outportb(NCT5523D_INDEX_PORT, NCT5523D_REG_LD);
outportb(NCT5523D_DATA_PORT, LD);
Lock_NCT5523D();
}
//--------------------------------------------------------------------------void Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_NCT5523D();
outportb(NCT5523D_INDEX_PORT, REG);
outportb(NCT5523D_DATA_PORT, DATA);
Lock_NCT5523D();
}
//--------------------------------------------------------------------------unsigned char Get_NCT5523D_Reg(unsigned char REG)
{
unsigned char Result;
Unlock_NCT5523D();
outportb(NCT5523D_INDEX_PORT, REG);
Result = inportb(NCT5523D_DATA_PORT);
Lock_NCT5523D();
return Result;
}
//-----------------------------------------------------------------------
Loading...