IBASE MI961 User Manual
MI961F
Intel ® H61 Express Chipset
Mini ITX Motherboard
USER’S MANUAL
Version 1.0A
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel is a registered trademark of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Fintek is a registered trademark of Fintek Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
MI961F User’s Manual
Table of Contents
Introduction ...................................................... 1
Product Description ............................................................ 1
Checklist ............................................................................. 2
MI961F Specifications ....................................................... 3
Board Dimensions .............................................................. 4
Installations ...................................................... 5
Installing the CPU .............................................................. 6
Installing the Memory......................................................... 7
Setting the Jumpers............................................................. 8
Connectors on MI961F ..................................................... 12
BIOS Setup.......................................................21
Drivers Installation ......................................45
Appendix ...........................................................54
A. I/O Port Address Map .................................................. 54
B. Interrupt Request Lines (IRQ) ...................................... 55
C. Watchdog Timer Configuration ................................... 56
MI961F User’s Manual iii
This page is intentionally left blank.
iv
MI961F User’s Manual
INTRODUCTION
Introduction
Product Description
The MI961F Mini ITX motherboard is based on the latest Intel@ H61
Express chipset. The platform supports 2nd generation Intel® Core™
processor family with LGA1155 packing and features an integrated
dual-channel DDR3 memory controller as well as a graphics core.
The latest Intel@ processors provide advanced performance in both
computing and graphics quality. This meets the requirement of customers
in the gaming, POS, digital signage and server market segment.
The H61 platform is made with 32 nanometer technology that supports
Intel’s first processor architecture to unite the CPU and the graphics core
on the transistor level. The MI961F board utilizes the dramatic increase in
performance provided by this Intel’s latest cutting-edge technology.
Measuring 170mm x 170mm, the MI961F offers 3Gbps SATA support (3
ports), USB3.0 (2 ports) and interfaces for DVI-D, VGA and HDMI
displays.
MI961F FEATURES:
Supports Intel@ 2nd Generation Core i7/i5/i3 QC/DC desktop
processors
Two DDR3 DIMM, 1066/1333MHz; supports up to 16GB
memory
Dual Realtek PCI-Express Gigabit LAN
Integrated Graphics for VGA, DVI-D/HDMI displays
3x SATA 2.0, 9x USB 2.0, USB 3.0 (2 ports),
4x COM, Watchdog timer
1x PCI-E (x16), 1x Mini PCI-E Socket (supports Mini PCI-E
card or MSATA)
MI961F User’s Manual 1
INTRODUCTION
Checklist
Your MI961F package should include the items listed below.
The MI961F Mini ITX motherboard
This User’s Manual
1 CD containing chipset drivers and flash memory utility
Serial ATA cable
2
MI961F User’s Manual
Form Factor
Mini-ITX
CPU Type
Intel® 2nd generation CoreTM i7/i5/i3/Pentium®/Celeron® DT processor
TDP for QC= 95W/65W/45W;DC= 65W/35W
[Package = FC-LGA10, 37.5 mm x 37.5mm]
CPU Speed
Up to 3.40 GHz
Cache Size
Up to 8MB shared L2 Cache
CPU Socket
LGA1155 (Socket H2)
Chipset
Intel® BD82H61 PCH (TDP=6.1W)
[27mm x 27mm, 942-pin FCBGA package]
BIOS
AMI BIOS, support ACPI Function
Memory
Intel® 2nd generation CoreTM i7/i5/i3/Pentium®/Celeron® DT processor
integrated memory controller support DDR3-1333 (Non-ECC)
UDIMM x 2, Max. =16GB
VGA
Intel® 2nd generation CoreTM i7/i5/i3/Pentium® DT processor integrated
Gfx(HD2000/HD3000)
CRT X 1, DVI-D X 1 (thru Level shifter ASM1442)
HDMI X 1 (thru Level shifter ASM1442)
LAN
Realtek RTL8111E PCIe Gigabit LAN controller x2
USB
USB 2.0 host controller, supports 10 ports
- 4 ports in the rear panel and 4 ports for onboard pin header
- 1 port for Mini PCIe
USB 3.0 host controller (ASM1042), support 2 ports
- 2 ports in the rear panel
Serial ATA
Intel® H61 PCH build-in SATA 2.0 controller, supports 3 ports
Audio
Intel® H61 PCH build-in built-in High Definition Audio controller: ALC892
w/ 7.1 channels
LPC I/O
Fintek F81866AD-I
COM1 (RS232/422/485) [Auto flow control]; COM2~4 (RS232 only)
COM1/2 with pin-9 with power for 2 ports (500 mA for each port)
Hardware Monitor (2 thermal inputs, 4 voltage monitor inputs & 3 Fan
headers, 2 x DC FAN supporting only, AUX FAN cannot)
CPU FAN = 4-pin type; others= 3-pin type
Digital IO
4 in & 4 out
Expansion Slots
PCIe(16x) x 1
Mini PCIe(1x) x1 [Full-sized type] w/ mSATA & USB
Edge Connector
Dual DB9 stack connector for COM1, COM2
DVI-D + CRT stack connector x 1
Dual USB(3.0) [BLUE color] + HDMI stack connector x1
RJ-45 GbE + dual USB (2.0) stack connector x2
RCA Jack 3 x 1 for HD Audio
Onboard
Header/
Connector
3 ports x SATA II
2x4 pin-header x2 for 4 ports USB 2.0
2x5 pin-header x1 for front panel audio
DF11-10 for COM3, DF11-10 for COM4
2x5 pin-header x1 for Digital I/O
2x5 male connector for LPC module [Debugging purpose only]
Watchdog Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
iSmart function
TI MSP430G2433 Micro-processor (Remote On/Off Control)
System Voltage
+5V, +3.3V, +12V, -12V, 5VSB (2A)
24-pin ATX main power + 4-pin 12V
Other
- Single LAN only to support LAN Wakeup while EuP is enabled
- Atmel AT24C02C EEPROM [SO8 type] for RTC back via SMbus
RoHS
Yes
Board Size
170mm x 170mm
MI961F Specifications
INTRODUCTION
MI961F User’s Manual 3
INTRODUCTION
[
Board Dimensions
4
MI961F User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the MI961F in order to set up a workable system. The
topics covered are:
Installing the CPU ....................................................................... 6
Installing the Memory ................................................................. 7
Setting the Jumpers ..................................................................... 8
Connectors on MI961F ............................................................. 12
MI961F User’s Manual 5
INSTALLATIONS
NOTE:
Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
Installing the CPU
The MI961F board supports an LGA1155 Socket (shown below) for 2nd
generation Intel® Core™ processor family with LGA1155 packing.
To install the CPU, unlock first the socket by pressing the lever sideways,
then lift it up to a 90-degree. Then, position the CPU above the socket
such that the CPU corner aligns with the gold triangle matching the
socket corner with a small triangle. Carefully insert the CPU into the
socket and push down the lever to secure the CPU. Then, install the heat
sink and fan.
6
MI961F User’s Manual
INSTALLATIONS
DDR3 Module
Lock
Lock
Lock
Lock
Installing the Memory
The MI961F board supports four DDR3 memory socket for a maximum
total memory of 16GB in DDR3 DIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2. Gently push the DDR3 module in an upright position until the clips of
the slot close to hold the DDR3 module in place when the DDR3
module touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
MI961F User’s Manual 7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on MI961F to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MI961F and their respective functions.
Jumper Locations on MI961F .............................................................. 9
JP1: Factory use only (Default: open) ................................................ 10
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection .................... 10
JP5: COM1 RS232 RI/+5V/+12V Power Setting ............................... 10
JP6: COM2 RS232 RI/+5V/+12V Power Setting ............................... 10
JP7: Flash Descriptor Security Overide (Factory use only) ................. 11
JBAT1: Clear CMOS Contents .......................................................... 11
8
MI961F User’s Manual
Jumper Locations on MI961F
INSTALLATIONS
Jumpers on MI961F ........................................................................Page
JP1: Factory use only (Default: open) ................................................ 10
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection .................... 10
JP5: COM1 RS232 RI/+5V/+12V Power Setting ............................... 10
JP6: COM2 RS232 RI/+5V/+12V Power Setting ............................... 10
JP7: Flash Descriptor Security Override (Factory use only) ................ 11
JBAT1: Clear CMOS Contents .......................................................... 11
MI961F User’s Manual 9
INSTALLATIONS
COM1
Function
RS-232
RS-422
RS-485
Jumper
Setting
(pin closed)
JP2:
3-5&4-6
JP3:
1-2
JP4:
3-5 & 4-6
JP2:
1-3&2-4
JP3:
3-4
JP4:
1-3 & 2-4
JP2:
1-3&2-4
JP3:
5-6
JP4:
1-3 & 2-4
JP5
Setting
Function
Pin 1-2
Short/Closed
+12V
Pin 3-4
Short/Closed
RI
Pin 5-6
Short/Closed
+5V
JP6
Setting
Function
Pin 1-2
Short/Closed
+12V
Pin 3-4
Short/Closed
RI
Pin 5-6
Short/Closed
+5V
JP1: Factory use only (Default: open)
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection
JP5: COM1 RS232 RI/+5V/+12V Power Setting
JP6: COM2 RS232 RI/+5V/+12V Power Setting
10
MI961F User’s Manual
INSTALLATIONS
JP7
Override
Open
Disabled
(Default)
Close
Enabled
JBAT1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
JP7: Flash Descriptor Security Override (Factory use only)
JBAT1: Clear CMOS Contents
MI961F User’s Manual 11
INSTALLATIONS
Connectors on MI961F
Connector Locations on MI961F ....................................................... 13
CN1: COM1 and COM2 Serial Ports ................................................. 14
CN2: VGA and DVI-D Connector ..................................................... 14
CN3: USB3.0 Connector ................................................................... 15
CN4: HDMI Connector ..................................................................... 15
CN5, CN7, CN9: SATA Connectors ................................................. 15
CN6: Gigabit LAN + USB 2/3 ........................................................... 15
CN8: Gigabit LAN + USB 10/11 ....................................................... 15
CN10: HD Audio Connector ............................................................. 15
J1: ATX 12V Power Connector ......................................................... 16
J2: Digital I/O .................................................................................... 16
J3: LPC Connector (for debug use) .................................................... 16
J4, J5: COM3, COM4 RS232 Serial Ports ......................................... 16
J6: 24-pin ATX Power Connector...................................................... 17
J7: Power LED .................................................................................. 17
J8, J9, DDR3 DIMM Sockets ............................................................ 17
J10: System Function connector......................................................... 17
J12: Mini PCI-E Connector ............................................................... 18
J13, J17: USB Connectors ................................................................. 18
J14: SPI Connector (For debug use) .................................................. 18
J15: MCU JTAG (for debug use) ..................................................... 18
J18: Audio Pin Header for Chassis Front Panel .................................. 18
PCIE1: PCI-E X16 Slot ..................................................................... 19
CPU_FAN1: CPU Fan Power Connector ........................................... 19
SYS_FAN1: System Fan1 Power Connector...................................... 19
SYS_FAN2: System Fan2 Power Connector...................................... 19
12
MI961F User’s Manual
Connector Locations on MI961F
INSTALLATIONS
MI961F User’s Manual 13
INSTALLATIONS
Pin #
Signal Name
RS-232
R2-422
RS-485
1
DCD
TX-
DATA-
2
RX
TX+
DATA+
3
TX
RX+
NC
4
DTR
RX-
NC
5
Ground
Ground
Ground
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC
10
NC
NC
NC
VGA
Signal Name
Pin #
Pin #
Signal Name
Red
1 2 Green
Blue
3 4 N.C.
GND
5 6 GND
GND
7 8 GND
N.C.
9
10
GND
N.C.
11
12
DDCDATA
HSYNC
13
14
VSYNC
DDCCLK
15
CN1: COM1 and COM2 Serial Ports
[
CN2: VGA and DVI-D Connector
14
MI961F User’s Manual
INSTALLATIONS
Signal Name
Pin #
Pin #
Signal Name
DATA 2-
1
16
HOT POWER
DATA 2+
2
17
DATA 0-
GROUND
3
18
DATA 0+
N.C.
4
19
GROUND
N.C.
5
20
N.C.
DDC CLOCK
6
21
N.C.
DDC DATA
7
22
GROUND
N.C
8
23
CLOCK +
DATA 1-
9
24
CLOCK -
DATA 1+
10
GROUND
11
N.C.
12
N.C.
13
DDC POWER
14
GROUND
15
[
CN3: USB3.0 Connector
CN4: HDMI Connector
CN5, CN7, CN9: SATA Connectors
CN6: Gigabit LAN + USB 2/3
CN8: Gigabit LAN + USB 10/11
CN10: HD Audio Connector
MI961F User’s Manual 15
INSTALLATIONS
Pin #
Signal Name
1
Ground
2
Ground
3
+12V
4
+12V
Signal Name
Pin #
Pin #
Signal Name
GND
1 2 VCC
OUT3
3 4 OUT1
OUT2
5 6 OUT0
IN3
7 8 IN1
IN2
9
10
IN0
Signal Name
Pin #
Pin #
Signal Name
DCD, Data carrier detect
1 2 RXD, Receive data
TXD, Transmit data
3 4 DTR, Data terminal ready
GND, ground
5 6 DSR, Data set ready
RTS, Request to send
7 8 CTS, Clear to send
RI, Ring indicator
9
10
Not Used
J1: ATX 12V Power Connector
J2: Digital I/O
J3: LPC Connector (for debug use)
J4, J5: COM3, COM4 RS232 Serial Ports
16
MI961F User’s Manual
Loading...