IB908F
Intel® Haswell-ULT
3.5” Disk Size SBC
USER’S MANUAL
Version 1.1
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® 4th Generation Mobile Core
registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
NUVOTON is a registered trademark of NUVOTON Technology
Corporation.
All other product names or trademarks are properties of their
respective owners.
TM
i MCP Processor are
ii
IB908F User’s Manual
Table of Contents
Introduction ....................................................... 1
Product Description............................................................. 1
Checklist .............................................................................. 2
IB908F Specifications ......................................................... 2
Board Dimensions ............................................................... 4
Installations ....................................................... 5
Installing the Memory ......................................................... 6
Setting the Jumpers ............................................................. 7
Connectors on IB908F ...................................................... 11
BIOS Setup ....................................................... 23
Drivers Installation ...................................... 49
Intel Chipset Software Installation Utility ........................ 50
VGA Drivers Installation .................................................. 53
Realtek HD Audio Driver Installation .............................. 56
LAN Drivers Installation................................................... 58
Intel® Management Engine Interface ............................... 62
Intel® USB 3.0 Drivers ..................................................... 65
Appendix ............................................................ 68
A. I/O Port Address Map .................................................. 68
B. Interrupt Request Lines (IRQ) ...................................... 69
C. Watchdog Timer Configuration ................................... 70
IB908F User’s Manual iii
This page is intentionally left blank.
iv
IB908F User’s Manual
INTRODUCTION
Introduction
Product Description
The IB908F is a 3.5-inch single board computer based on the Intel
Haswell-ULT MCP processors.
The IB908F platform is well-suited for low-power and high-performance
designs in a broad range of markets including Industrial Control &
Automation, Digital Signage, Thin Client, Electronic Gaming Machines,
and SMB storage appliances.
IB908F Features:
Supports Intel® 4th generation mobile Core
Two DDR3L SO-DIMM, 1333/1600 MHz, Max. 16GB
memory
Integrated graphics for DVI-I, LVDS displays
2 x SATA III connector
2x COM port connector
2 x Mini-PCIe(x1) slot (w/ USB/MSATA support)
2x GbE (RJ-45) connector
1x 9V to 24V DC-IN power connector
TM
i MCP processors
®
IB908F User’s Manual 1
INTRODUCTION
Product Name
IB908F
Form Factor
3.5” SBC
CPU Type
- Intel® 4th generation mobile Core
TM
i MCP processors (22nm
monolithic)
- TDP = 15W (DC) , FCBGA1168 @ solder side
CPU Speed
Intel® CoreTM i7-4650U processor (1.7GHz) [IB908AF-4650]
Intel® CoreTM i5-4300U processor (1.9GHz) [IB908AF-4300]
Intel® CoreTM i3-4010U processor (1.7GHz) [IB908F-4010]
Intel® Celeron® 2980U processor (1.6GHz) [IB908F-2980]
Cache
Up to 4MB
Chipset
Integrated in Intel® 4th Generation CoreTM i U-series processor
BIOS
AMI BIOS
Memory
Intel® 4th Gen. CoreTM i U-series processor integrated memory
controller
- DDR3L (1.35V) @1600 MHz, SO-DIMM [204-pin vertical] x 2
- Max. 16GB, Non-ECC
Display
Intel® 4th Gen. CoreTM i U-series processor integrated Gfx,
supports 3 independent displays, Direct X 11.1, OpenGL 3.2,
Open CL 1.2
- DVI-I x 1 (Thru DDI#1 w/ Level shifter [ASM1442K] for DVI +
DP to VGA [NXP PTN3392] )
LVDS
- LVDS(Thru eDP, via NXP PTN3460 bridge IC)
24-bit dual channels LVDS interface w/DF20 socket x2
LAN
®
I218LM GbE PHY (IB908AF-4650& IB908AF-4300)
or I218V GbE PHY (IB908F-4010 & IB908F-2980)
®
I211AT as 2nd GbE
USB
- Intel® 4th Gen. CoreTM i U-series processor integrated USB 2.0
host controller, supports 4 x USB 2.0: 2-ports onboard pin
header + 2 port thru MiniPCIe
- Intel® 4th Gen. CoreTM i U-series processor integrated USB 3.0
host controller, supports 2 x USB 3.0 in the rear panel
Checklist
Your IB908F package should include the items listed below.
The IB908F SBC
This User’s Manual
1 CD containing chipset drivers and flash memory utility
Optional cable kit (containing DC in power cable/PW87, COM
port cable / PK1H, SATA & HDD power cable/SATA-26 and
USB 2.0 cable/USB-29)
Other options: Audio-18 audio cable, HSIB908-BGA-1 heatsink
IB908F Specifications
2
IB908F User’s Manual
INTRODUCTION
Serial ATA Ports
Intel® 4th Gen. CoreTM i U-series processor built-in SATA
controller
2 x SATA 3.0 (6Gbps) and 2 x mSATA via MiniPCIe slots
(w/NXP CBTL02043A switching IC)
Audio
Intel® 4th Gen. CoreTM i U-series processor built-in High
Definition Audio controller + Realtek ALC269Q-VC2-GR Codec
[6mm x 6mm @ MQFN48]
w/ class-D speaker amplifier(2W per channel @ 5V power
supply)
LPC I/O
Nuvoton NCT6102D [128-pin LQFP, 14 mm x 14mm x 1.4mm)
COM1 (RS232/422/485) [EXAR SP339EER1 232/422/485
transceiver for jumper-less]; COM2 (RS232 only) [SIPEX
SP3243EBER, QFN32]
[Hardware Monitor]
2 x Thermal inputs
2 x Voltage monitoring
1 x CPU Fan (PWM Fan type, 4-pin connector)
Digital IO
4 in & 4 out
iAMT(9.5)
For IB908AF-4650 / IB908AF-4300
Expansion Slots
1x mSATA/mPCIe(x1) w/ USB signal [Half-sized]
1x mSATA/mPCIe(x1) w/ USB signal [Full-sized]
Edge Connector
DVI-I x 1
RJ45 x2 for LAN#1 & #2
USB 3.0 stack connector x 1 for USB1 / 2 [Blue color]
DB9 x 1 for COM #1
Onboard
Header/Connector
DF20-20 socket connector x 2 for 24-bit dual channel LVDS
2 ports x SATA III [Blue color]
2x4 pins header x 1 for 2 USB 2.0 ports [DF11]
2x6 pins box header x1 for Audio [DF11]
1x4 pins box header x1 for Speaker out
2x5 pins box header x1 for COM2
2x5 pins headers x 1 for LPC (Debug purposes only)
5 pins box header x1 for smart battery
4 pins box header x1 for backlight/brightness control
4 pins power connector x1 for SATA HDD
2 pins power connector x1 for DC-in [180 degree vertical type]
Watchdog Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
Power Input
+9V ~ +24V DC-in
RoHS
Yes
Board Size
102mm x 147mm
OS supported
Windows 8 / Embedded; Windows 7 / Embedded Linux
Others
IB908F User’s Manual 3
INTRODUCTION
Board Dimensions
4
IB908F User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the IB908F in order to set up a workable system. The
topics covered are:
Installing the Memory ............................................................................ 6
Setting the Jumpers ................................................................................ 7
Connectors on IB908F ......................................................................... 11
IB908F User’s Manual 5
INSTALLATIONS
Installing the Memory
The IB908F board supports TWO DDR3L memory socket for a
maximum total memory of 16GB DDR3L memory type.
Installing and Removing Memory Modules
To install the DDR3L modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3L module so that the key of the DDR3L module
aligned with that on the memory slot.
2. Gently push the DDR3L module in an upright position until the clips
of the slot close to hold the DDR3L module in place when the
DDR3L module touches the bottom of the slot.
3. To remove the DDR3L module, press the clips with both hands.
6
IB908F User’s Manual
INSTALLATIONS
Setting the Jumpers
Jumpers are used on IB908F to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB908F and their respective functions.
Jumper Locations on IB908F ................................................................. 8
J3: Clear CMOS Contents...................................................................... 9
J4: Clear ME Contents ........................................................................... 9
J7: Flash Descriptor Security Override (Factory use only) .................. 10
J9: LVDS Panel Power Selection ........................................................ 10
IB908F User’s Manual 7
INSTALLATIONS
Jumper Locations on IB908F
Jumpers on IB908F .......................................................................... Page
J3: Clear CMOS Contents ...................................................................... 9
J4: Clear ME Contents ........................................................................... 9
J9: LVDS Panel Power Selection ......................................................... 10
8
IB908F User’s Manual
J3
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
J4
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear ME RTC
REGISTER
3
1
3
1
J3: Clear CMOS Contents
INSTALLATIONS
J4: Clear ME Contents
IB908F User’s Manual 9
INSTALLATIONS
J7
Flash Descriptor
Security Override
Open
Disabled (Default)
Close
Enabled
J9
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V (default)
Pin 2-3
Short/Closed
5V
1
3
J7: Flash Descriptor Security Override (Factory use only)
J9: LVDS Panel Power Selection
10
IB908F User’s Manual
INSTALLATIONS
Connectors on IB908F
Connector Locations on IB908F .......................................................... 12
CN3, CN4: Gigabit LAN ..................................................................... 13
CN3: Intel® Clarkville I218V/I218LM GbE PHY ............................... 13
CN4: Intel® Pearsonville I211AT as 2nd GbE ................................... 13
CN5: USB 1/2 Connector .................................................................... 13
CN6: VGA DVI-I Connector ............................................................... 13
CN7: DB9 Connector .......................................................................... 13
CN1, CN2: SATA Connectors ............................................................. 14
JP1: LCD Backlight Connector ........................................................... 14
JP2: USB3/4 Connector ....................................................................... 14
J2: Audio Connector (DF11 Connector) .............................................. 15
JP3, JP5: LVDS Connectors (LVDS1,LVDS2) ................................... 15
JP4: SPI Flash Connector (factory use only) ....................................... 16
J5: Amplifier Connector ...................................................................... 16
J7: Factory use only ............................................................................. 16
JP6: SATA HDD Power Connectors ................................................... 17
JP7: Debug 80 Port Connector (factory use only) ............................... 17
J12: Smart Battery ............................................................................... 18
J13: Board Input Power Connector ...................................................... 18
J14: Front Panel Connector ................................................................. 19
J15: Mini PCIE Connector (Supports mSATA) .................................. 20
J16: Mini PCIE Connector (Half Size/ Supports mSATA) .................. 20
J17: COM2/RS232 Serial Port ............................................................ 20
J19: Digital I/O Connector ................................................................... 21
CPU_FAN1: CPU Fan Power Connector ........................................... 21
IB908F User’s Manual 11
INSTALLATIONS
Connector Locations on IB908F
12
IB908F User’s Manual
INSTALLATIONS
Signal Name
Pin #
Pin #
Signal Name
DCD, Data carrier detect
1 6 DSR, Data set ready
RXD, Receive data
2 7 RTS, Request to send
TXD, Transmit data
3 8 CTS, Clear to send
DTR, Data terminal ready
4 9 RI, Ring indicator
GND, ground
5
10
Not Used
Pin #
Signal Name
RS-232
R2-422
RS-485
1
DCD
TX-
DATA-
2
RX
TX+
DATA+
3
TX
RX+
NC
4
DTR
RX-
NC
5
Ground
Ground
Ground
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC 9 RI
NC
NC
10
NC
NC
NC
CN3, CN4: Gigabit LAN
CN3: Intel® Clarkville I218V/I218LM GbE PHY
CN4: Intel® Pearsonville I211AT as 2nd GbE
CN5: USB 1/2 Connector
CN6: VGA DVI-I Connector
CN7: DB9 Connector
(COM1) is a DB-9 connector.
COM1 is jumper-less for RS-232, RS-422 and RS-485 and is to be
configured with BIOS Selection.
[
IB908F User’s Manual 13
INSTALLATIONS
Pin #
Signal Name
1
+12V
2
Backlight Enable
3
Brightness Control
4
Ground
Signal Name
Pin #
Pin #
Signal Name
Vcc
1 2 Ground
D0-
3 4 D1+
D0+
5 6 D1-
Ground
7 8 Vcc
4 1
2 1
8 7
CN1, CN2: SATA Connectors
JP1: LCD Backlight Connector
JP2: USB3/4 Connector
14
IB908F User’s Manual
Signal Name
Pin #
Pin #
Signal Name
LINEOUT_R
2 1 LINEOUT_L
Ground
4 3 JD_FRONT
LINEIN_R
6 5 LINEIN_L
Ground
8 7 JD_LINEIN
MIC-R
10 9 MIC_L
Ground
12
11
JD_MIC1
Signal Name
Pin #
Pin #
Signal Name
TX0N
2 1 TX0P
Ground
4 3 Ground
TX1N
6 5 TX1P
Ground
8 7 Ground
TX2N
10 9 TX2P
Ground
12
11
Ground
CLKN
14
13
CLKP
Ground
16
15
Ground
TX3N
18
17
TX3P
Power
20
19
Power
1 11
2 12
2
20
1
19
J2: Audio Connector (DF11 Connector)
INSTALLATIONS
JP3, JP5: LVDS Connectors (LVDS1,LVDS2)
The LVDS connectors (Hirose DF20G-20DP-1V) on board consist
of the first channel (LVDS1) and second channel (LVDS2).
IB908F User’s Manual 15
INSTALLATIONS
Pin #
Signal Name
1
OUTL+
2
OUTL-
3
OUTR-
4
OUTR+
9 10
1 2
1
4
1 2
JP4: SPI Flash Connector (factory use only)
J5: Amplifier Connector
J6, J8: DDR3L SO-DIMM Sockets
J7: Factory use only
16
IB908F User’s Manual
Pin #
Signal Name
1
+5V
2
Ground
3
Ground
4
+12V
1
4
1
4
2 10
1 9
JP6: SATA HDD Power Connectors
INSTALLATIONS
JP7: Debug 80 Port Connector (factory use only)
J11: MCU Flash Connector (factory use only)
IB908F User’s Manual 17
INSTALLATIONS
Pin #
Signal Name
1
RST#
2
ICHSWI#
3
Ground
4
SMB_DATA
5
SMB_CLK
Pin #
Signal Name
1
+9V to +24V
2
GND
1
2
1
5
J12: Smart Battery
J13: Board Input Power Connector
18
IB908F User’s Manual
INSTALLATIONS
Signal Name
Pin #
Pin #
Signal Name
Ground
1 2 PWR_SW
PWR_LED+
3 4 PWR_LED-
HDD_LED+
5 6 HDD_LED-
Ground
7 8 RESET
Pin #
Signal Name
3
LED(+)
4
LED(-)
Pin #
Signal Name
5
LED(+)
6
LED(-)
1
7
2
8
J14: Front Panel Connector
The following table shows the pin outs of the 2x4 pin header
J14 provides connectors for system indicators that provide light
indication of the computer activities and switches to change the computer
status.
J14 is an 8-pin header that provides interfaces for the following
functions.
ATX Power ON Switch: Pins 1 and 2
This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the system that connects to the power switch on
the case. When pressed, the power switch will force the
system to power on. When pressed again, it will force the
system to power off.
Power LED: Pins 3 and 4
Hard Disk Drive LED Connector: Pins 5 and 6
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
IB908F User’s Manual 19
INSTALLATIONS
Signal Name
Pin #
Pin #
Signal Name
DCD, Data carrier detect
1 2 RXD, Receive data
TXD, Transmit data
3 4 Data terminal ready
GND, ground
5 6 DSR, Data set ready
RTS, Request to send
7 8 CTS, Clear to send
RI, Ring indicator
9
10
Not Used
2 1
10 9
Reset Switch: Pins 7 and 8
The reset switch allows the user to reset the system without
turning the main power switch off and then on again.
Orientation is not required when making a connection to this
header.
J15: Mini PCIE Connector (Supports mSATA)
J16: Mini PCIE Connector (Half Size/ Supports mSATA)
** The gap of height between J15 & J16 is following PCI Express Mini Card
electromechanical spec. **
J17: COM2/RS232 Serial Port
20
IB908F User’s Manual
Signal Name
Pin #
Pin #
Signal Name
GND
1 2 VCC
OUT3
3 4 OUT1
OUT2
5 6 OUT0
IN3
7 8 IN1
IN2
9
10
IN0
Pin #
Signal Name
1
Ground
2
+12V
3
Rotation detection
4
Control
4
1
2 10
1 9
J19: Digital I/O Connector
INSTALLATIONS
CPU_FAN1: CPU Fan Power Connector
IB908F User’s Manual 21
INSTALLATIONS
This page is intentionally left blank.
22
IB908F User’s Manual
DRIVERS INSTALLATION
BIOS Setup
This chapter describes the different settings available in the BIOS that
comes with the board. The topics covered in this chapter are as follows:
BIOS Introduction ............................................................................... 24
BIOS Setup .......................................................................................... 24
Advanced Settings ............................................................................... 26
Chipset Settings ................................................................................... 39
Boot Settings........................................................................................ 45
Security Settings .................................................................................. 47
Save & Exit Settings ............................................................................ 48
IB908F User’s Manual 23
BIOS SETUP
BIOS Introduction
The BIOS (Basic Input/Output System) installed in your computer
system’s ROM provides critical low-level support for a standard device
such as disk drives, serial ports and parallel ports. It also adds virus and
password protection as well as special support for detailed fine-tuning of
the chipset controlling the entire system.
BIOS Setup
The BIOS provides a Setup utility program for specifying the system
configurations and settings. The BIOS ROM of the system stores the
Setup utility. When you turn on the computer, the BIOS is immediately
activated. Pressing the <Del> key immediately allows you to enter the
Setup utility. If you are a little bit late pressing the <Del> key, POST
(Power On Self Test) will continue with its test routines, thus preventing
you from invoking the Setup. If you still wish to enter Setup, restart the
system by pressing the ”Reset” button or simultaneously pressing the
<Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the
system Off and back On again. The following message will appear on the
screen:
Press <DEL> or <ESC> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to select,
the <PgUp> and <PgDn> keys to change entries, <F1> for help and
<Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
24
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
BIOS Information
Choose the system default
language
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
Total memory
8176 MB (DDR3)
Memory Frequency
1600 Mhz
System Date
[Tue 10/29/2013]
System Time
[15:27:20]
Access Level
Administrator
Main Settings
Aptio Setup Utility – Copyright © 2011 American Megatrends, Inc.
System Date
Set the Date. Use Tab to switch between Data elements.
System Time
Set the Time. Use Tab to switch between Data elements.
IB908F User’s Manual 25
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
► PCI Subsystem Settings
► ACPI Settings
► Wake up event setting
► CPU Configuration
► SATA Configuration
► Shutdown Temperature Configuration
► ISmart Controller
► USB Configuration
► NCT6102D Super IO Configuration
► NCT6102D H/W Monitor
Main Advanced Chipset Boot Security Save & Exit
PCI Bus Driver Version V 2.0502
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
PCI Common Settings
PCI Latency Timer
32 PCI Bus Clocks
VGA Palette Snoop
Disabled
PERR# Generation
Disabled
SERR# Generation
Disabled
► PCI Express Settings
Advanced Settings
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
PCI Subsystem Settings
Aptio Setup Utility
Aptio Setup Utility
PCI Latency Timer
Value to be programmed into PCI Latency Timer Register.
VGA Palette Snoop
Enables or disables VGA Palette Registers Snooping.
PERR# Generation
Enables or disables PCI device to generate PERR#.
SERR# Generation
Enables or disables PCI device to generate SERR#.
26
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
PCI Express Device Register Settings
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Relaxed Ordering
Disabled
Extended Tag
Disabled
No Snoop
Enabled
Maximum Payload
Auto
Maximum Read Request
Auto
PCI Express Link Register Settings
ASPM Support
Disabled
WARNING: Enabling ASPM may cause
PCI-E devices to fail
Extended Synch
Disabled
Link Training Retry
5 Link Training Timeout (uS)
100 Unpopulated Links
Keep Link ON
Restore PCIE Registers
Disabled
PCI Express Settings
Aptio Setup Utility
Relaxed Ordering
Enables or disables PCI Express Device Relaxed Ordering.
Extended Tag
If ENABLED allows device to use 8-bit Tag field as a requester.
No Snoop
Enables or disables PCI Express Device No Snoop option.
Maximum Payload
Set Maximum Payload of PCI Express Device or allow System BIOS to
select the value.
Maximum Read Request
Set Maximum Read Request Size of PCI Express Device or allow System
BIOS to select the value.
ASPM Support
Set the ASPM Level: Force L0s – Force all links to L0s State:
AUTO – BIOS auto configure: DISABLE – Disables ASPM.
Extended Synch
If ENABLED allows generation of Extended Synchronization patterns.
IB908F User’s Manual 27
BIOS SETUP
Link Training Retry
Defines number of Retry Attempts software will take to retrain the link if
previous training attempt was unsuccessful.
Link Training Timeout (uS)
Defines number of Microseconds software will wait before polling ‘Link
Training’ bit in Link Status register. Value range from 10 to 1000 uS.
Unpopulated Links
In order to save power, software will disable unpopulated PCI Express
links, if this option set to ‘Disable Link’.
Restore PCIE Registers
On non-PCI Express aware OS’s (Pre Windows Vista) some devices may
not be correctly reinitialized after S3.Enabling this restore PCI Express
device configuration on S3 resume
Warning: Enabling this may cause issues with other hardware after S3
resume.1
28
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
ACPI Settings
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
Enable Hibernation
Enabled
ACPI Sleep State
S3 (Suspend to R…)
Lock Legacy Resources
S3 Video Repost
Disabled
Disabled
ACPI Settings
Aptio Setup Utility
Enable Hibernation
Enables or Disables System ability to hibernate (OS/S4 Sleep State). This
option may be not effective with some OS.
ACPI Sleep State
Select ACPI sleep state the system will enter, when the SUSPEND button
is pressed.
Lock Legacy Resources
Enabled or Disabled Lock of Legacy Resources.
S3 Video Repost
Enable or disable S3 Video Repost.
IB908F User’s Manual 29
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Wake on PCIE Wake Event
Disabled
Wake up event settings
Aptio Setup Utility
Wake on PCIE PME Wake Event
The options are Disabled and Enabled.
30
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
CPU Configuration
Intel(R) CPU Core(TM)i3-4010U @ 1.70GHz
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
CPU Signature
Processor Family
Microcode Patch
FSB Speed
40651
6
16
100MHz
Max CPU Speed
1700 MHz
Min CPU Speed
800 MHz
CPU Speed
800 MHz
Processor Cores
2
Intel HT Technology
Supported
Intel VT-x Technology
Supported
Intel SMX Technology
Not Supported
64-bit
Supported
EIST
Supported
CPU C3 State
CPU C6 State
CPU C7 State
Supported
Supported
Supported
L1 Data Cache
L1 Code Cache
L2 Cache
L3Cache
Supported
Supported
Supported
Supported
Hyper-threading
Enabled
Active Processor Cores
Overclocking lock
All
Disabled
Limit CPUID Maximum
Disabled
Execute Disable Bit
Enabled
Intel Virtualization Technology
Enabled
CPU AES
EIST
Enabled
Enabled
CPU Configuration
This section shows the CPU configuration parameters.
Aptio Setup Utility
Hyper-threading
Select the performance state that the BIOS will set before OS handoff.
Active Processor Cores
Number of cores to enable in each processor package.
Overclocking lock
Flex_RATIO(194)MSR
IB908F User’s Manual 31
BIOS SETUP
Limit CPUID Maximum
Disabled for Windows XP.
Execute Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when
combined with a supporting OS
Intel Virtualization Technology
When enabled, a VMM can utilize the additional hardware capabilities
provided by Vanderpool Technology.
CPU AES
Enabled/Disabled CPU Advanced Encryption Standard instructions
EIST
Enabled/Disabled Intel Speedstep.
32
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
SATA Controller(s)
Enabled
SATA Mode Selection
AHCI
SATA Port0
Empty
Software Preserve
Hot Plug
Unknown
Disabled
SATA Port1
Empty
Software Preserve
Hot Plug
Unknown
Disabled
SATA Port2
Empty
Software Preserve
Hot Plug
Unknown
Disabled
SATA Port3
Empty
Software Preserve
Hot Plug
Unknown
Disabled
SATA Configuration
SATA Devices Configuration.
Aptio Setup Utility
SATA Controller(s)
Enable / Disable Serial ATA Controller.
SATA Mode Selection
(1) AHCI Mode.
(2) RAID Mode.
Hot Plug
Designates this port as Hot P;uggable.
IB908F User’s Manual 33
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
APCI Shutdown Temperature
Disabled
Main Advanced Chipset Boot Security Save & Exit
ISmart Controller
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
Power-On after Power failure
Disable
Schedule Slot 1
None
Schedule Slot 2
None
Shutdown Temperature Configuration
Aptio Setup Utility
ACPI Shutdown Temperature
The default setting is Disabled.
ISmart Controller
Aptio Setup Utility
Power-On after Power failure
Enable or Disable.
Schedule Slot 1 / 2
Setup the hour/minute for system power on.
34
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Intel AMT
Enabled
BIOS Hotkey Pressed
Disabled
MEBx Selection Screen
Disabled
Hide Un-Configure ME Confirmation
Disabled
Un-Configure ME
Disabled
Amt Wait Timer
0
Activate Remote Assistance Process
Disabled
USB Configure
Enabled
PET Progress
Enabled
AMT CIRA Timeout
0
Watchdog
Disabled
OS Timer
0
BIOS Timer
0
AMT Configuration
Aptio Setup Utility
AMT Configuration
This configuration is supported iAMT function. Options are Enabled and
Disabled.
Note: iAMT H/W is always enabled. This option just controls the BIOS
extension execution. If enabled, this requires additional firmware in the
SPI device.
Unconfigure ME
Perform AMT/ME unconfigure without password operation.
Amt Wait Timer
Set timer to wait before sending ASF_GET_BOOT_OPTIONS.
Activate Remote Assistance Process
Trigger CIRA boot.
PET Progress
User can Enable/Disable PET Events progress to receive PET events or
not.
Watchdog Timer
Enable/Disable Watchdog Timer.
IB908F User’s Manual 35
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
USB Configuration
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
USB Module Version
8.10.27
USB Devices:
1 Keyboard, 1 Mouse
Legacy USB Support
Enabled
USB3.0 Support
Enabled
XHCI Hand-off
Enabled
EHCI Hand-off
Enabled
USB hardware delays and time-outs:
USB Transfer time-out
20 sec
Device reset tine-out
20 sec
Device power-up delay
Auto
USB Configuration
Aptio Setup Utility
Legacy USB Support
Enables Legacy USB support.
AUTO option disables legacy support if no USB devices are connected.
DISABLE option keeps USB devices available only for EFI applications.
USB3.0 Support
Enable/Disable USB3.0 (XHCI) Controller support.
XHCI Hand-off
This is a workaround for OSes without XHCI hand-off support. The
XHCI ownership change should be claimed by XHCI driver.
EHCI Hand-off
Enabled/Disabled. This is a workaround for OSes without EHCI hand-off
support. The EHCI ownership change should be claimed by EHCI driver.
USB Transfer time-out
The time-out value for Control, Bulk, and Interrupt transfers.
Device reset time-out
USB mass Storage device start Unit command time-out.
Device power-up delay
Maximum time the device will take before it properly reports itself to the
Host Controller. ‘Auto’ uses default value: for a Root port it is 100ms, for
a Hub port the delay is taken from Hub descriptor.
36
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
NCT6102D Super IO Configuration
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
NCT6102D Super IO Chip
NCT6102D
► Serial Port 0 Configuration
► Serial Port 1 Configuration
NCT6102D Super IO Configuration
Aptio Setup Utility
Serial Port Configuration
Set parameters of serial ports. User can Enable/Disable the serial port
and Select an optimal settings for the Super IO Device.
IB908F User’s Manual 37
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
PC Health Status
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
Smart Fan Function
Disabled
SYS Temp
+40 C
CPU Temp
CpuFan Speed
+43 C
4166
Vcore
+1.808 V
+5V
+4.918 V
+12V
+12.000 V
1.35V
+1.376 V
NCT6102D H/W Monitor
Aptio Setup Utility
Smart Fan Function
This field enables or disables the smart fan feature. At a certain
temperature, the fan starts turning. Once the temperature drops to a
certain level, it stops turning again.
Temperatures/Voltages
These fields are the parameters of the hardware monitoring function
feature of the board. The values are read-only values as monitored by the
system and show the PC health status.
38
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
► PCH-IO Configuration
► System Agent (SA) Configuration
Main Advanced Chipset Boot Security Save & Exit
Intel PCH RC Version 1.6.2.0
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Intel PCH SKU Name
Premium SKU
Intel PCH Rev ID
03/B1
► PCI Express Configuration
► USB Configuration
► PCH Azalia Configuration
PCH LAN Controller
Enabled
Wake on LAN
Disabled
SLP_S4 Assertion Width
1-2 Seconds
Chipset Settings
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
PCH-IO Configuration
This section allows you to configure the North Bridge Chipset.
Aptio Setup Utility
Aptio Setup Utility
PCH LAN Controller
Enable or disable onboard NIC.
Wake on LAN
Enable or disable integrated LAN to wake the system. (The Wake On
LAN cannot be disabled if ME is on at Sx state.)
SLP_S4 Assertion Width
Select a minimum assertion width of the SLP_S4# signal.
IB908F User’s Manual 39
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
PCI Express Configuration
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
PCI Express Clock Gating
Disabled
DMI Link ASPM Control
Disabled
DMI Link Extended Synch Control
Disabled
PCIe-USB Glitch W/A
Disabled
PCIE Root Function Swapping
Subtractive Decode
Disabled
Disabled
► PCI Express Root Port 1
► PCI Express Root Port 2
► PCI Express Root Port 3
► PCI Express Root Port 4
► PCI-E Port 5 is assigned to LAN
► PCI Express Root Port 6
PCI Express Configuration
PCI Express Clock Gating
Enable or disable PCI Express Clock Gating for each root port
DMI Link ASPM Control
The control of Active State Power Management on both NB side and SB
side of the DMI link.
PCIe-USB Glitch W/A
PCIe-USB Glitch W/A for bad USB device(s) connected behind
PCIE/PEG port.
40
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
USB Configuration
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
USB Precondition
Disabled
xHCI Mode
Auto
xHCI Idle L1
Enabled
USB Ports Per-Port Disable Control
Disabled
Main Advanced Chipset Boot Security Save & Exit
PCH Azalia Configuration
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Azalia
Auto
Azalia PME
Disabled
USB Configuration
USB Precondition
Precondition work on USB host controller and root ports for faster
enumeration.
xHCI Mode
Mode of operation of xHCI controller.
USB Ports Per-Port Disable Control
Control each of the USB ports (0~13) disabling.
PCH Azalia Configuration
Azalia
Control Detection of the Azalia device.
Disabled = Azalia will be unconditionally be disabled.
Enabled = Azalia will be unconditionally be enabled.
Auto = Azalia will be enabled if present, disabled otherwise.
Azalia PME
Enable or disable power management capability of the audio controller.
IB908F User’s Manual 41
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
System Agent Bridge Name Haswell
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
System Agent RC Version
1.6.2.0
VT-d Capability
Supported
VT-d
Enabled
► Graphics Configuration
Main Advanced Chipset Boot Security Save & Exit
Graphics Configuration
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
IGFX VBIOS Version
2166
IGfx Frequency
400 MHz
Primary Display
Primary PEG
Primary PCIE
Auto
Auto
Auto
Internal Graphics
Auto
Aperture Size
256MB
DVMT Pre-Allocated
32M
DVMT Total Gfx Mem
► LCD Control
256MB
System Agent (SA) Configuration
Aptio Setup Utility
VT-d
Check to enable VT-d function on MCH.
Graphics Configuration
Aptio Setup Utility
Primary Display
Select which of IGFX/PEG/PCI graphics device should be primary
display or select SG for switchable Gfx.
42
IB908F User’s Manual
DRIVERS INSTALLATION
Primary PEG
Select PEGO/PEG1/PEG2/PEG3 Graphics device should be Primary
PEG.
Primary PCIE
Select PCIE0/PCIE1/PCIE2/PCIE3/PCIE4/PCIE5/PCIE6PCIE7
Graphics device should be primary PCIE.
Internal Graphics
Keep IGD enabled based on the setup options.
DVMT Pre-Allocated
Select DVMT 5.0 Pre-Allocated (Fixed) graphics memory size used by
the internal graphics device.
DVMT Total Gfx Mem
Select DVMT 5.0 total graphics memory size used by the internal
graphics device.
LCD Control
Select the Video Device that will be activated during POST. This has no
effect if external graphics present. Secondary booty display selection will
appear based on your selection. VGA modes will be supported only on
primary display.
IB908F User’s Manual 43
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
LCD Control
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save & Exit
ESC: Exit
Primary IGFX Boot Display
VBIOS Default
LCD Panel Type
DC Output level
1024x768 LVDS
LEVEL4
LCD Chanel Type
LVDS BackLight brightness volt Control
Active LFP
Single
3.3V
No LVDS
Panel Color Depth
24 Bit
LCD Control
Aptio Setup Utility
Primary IGFX Boot Display
Select the Video Device, which will be activated during POST. This has
no effect if external graphics present.
Secondary boot display selection will appear based on your selection.
VGA modes will be supported only on primary display.
LCD Panel Type
Select LCD panel used by Internal Graphics Device by selecting the
appropriate setup item: 640x480 LVDS ~ 2048x1536 LVDS.
DC Output level
Backlight Brightness Control
LCD Chanel Type
Select LCD Chanel Type
LVDS Back Light Brightness Volt Control
LVDS Back Light Volt Control: 3.3V, 5V
Active LFP
Select the Active LFP Configuration.
No LVDS: VBIOS does not enable LVDS.
Int-LVDS: VBIOS enables LVDS driver by Integrated encoder.
SDVO LVDS: VBIOS enables LVDS driver by SDVO encoder.
eDP Port-A: LFP Driven by Int-DisplayPort encoder from Port-A.
Panel Color Depth
Select the LFP Panel Color Depth: 18 Bit, 24 Bit.
44
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
Boot Configuration
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
Setup Prompt Timeout
1
Bootup NumLock State
On
Quiet Boot
Disabled
Fast Boot
Disabled
Boot Option Priorities
► CSM16 Parameters
CSM Parameters
Boot Settings
This section allows you to configure the boot settings.
Setup Prompt Timeout
Number of seconds to wait for setup activation key.
65535(0xFFFF) means indefinite waiting.
Bootup NumLock State
Select the keyboard NumLock state.
Quiet Boot
Enables/Disables Quiet Boot option.
Fast Boot
Enables/Disables boot with initialization of a minimal set of devices
required to launch active boot option. Has no effect for BBS boot
options.
Boot Option Priorities
Sets the system boot order.
Aptio Setup Utility
IB908F User’s Manual 45
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
Launch CSM
Emabled
Boot option filter
UEFI and Legacy
Launch PXE OpROM policy
Do not launch
Launch Storage OpROM policy
Legacy only
Launch Video OpROM policy
Legacy only
Other PCI device ROM priority
Legacy OpROM
CSM parameters
OpROM execution, boot options, filter, etc.
Aptio Setup Utility
Launch CSM
This option controls if CSM will be launched.
Boot option filter
This option controls what devices system can boot to.
Launch PXE OpROM policy
Controls the execution of UEFI and Legacy PXE OpROM.
Launch Storatge OpROM policy
Controls the execution of UEFI and Legacy Storage OpROM.
Launch Video OpROM policy
Controls the execution of UEFI and Legacy Video OpROM.
Other PCI device ROM priority
For PCI devices other than Network, Mass storage or Video defines
which OpROM to launch.
46
IB908F User’s Manual
DRIVERS INSTALLATION
Main Advanced Chipset Boot Security Save & Exit
Password Description
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
If ONLY the Administrator’s password is set, then
this only limit access to Setup and is only asked
for when entering Setup.
If ONLY the User’s password is set, then this is a
power on password and must be entered to boot
or enter Setup. In Setup the User will have
Administrator rights
The password length must be
in the following range:
Minimum length
3
Maximum length
20
Administrator Password
User Password
Security Settings
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
Administrator Password
Set Setup Administrator Password.
User Password
Set User Password.
Aptio Setup Utility
IB908F User’s Manual 47
BIOS SETUP
Main Advanced Chipset Boot Security Save & Exit
Save Changes and Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save
ESC: Exit
Discard Changes and Exit
Save Changes and Reset
Discard Changes and Reset
Save Options
Save Changes
Discard Changes
Restore Defaults
Save as User Defaults
Restore User Defaults
Save & Exit Settings
Save Changes and Exit
Exit system setup after saving the changes.
Discard Changes and Exit
Exit system setup without saving any changes.
Save Changes and Reset
Reset the system after saving the changes.
Discard Changes and Reset
Reset system setup without saving any changes.
Save Changes
Save Changes done so far to any of the setup options.
Discard Changes
Discard Changes done so far to any of the setup options.
Restore Defaults
Restore/Load Defaults values for all the setup options.
Save as User Defaults
Save the changes done so far as User Defaults.
Restore User Defaults
Restore the User Defaults to all the setup options.
48
IB908F User’s Manual
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers. The software and drivers are included with the board. If you find
the items missing, please contact the vendor where you made the
purchase. The contents of this section include the following:
Intel Chipset Software Installation Utility ........................................... 50
VGA Drivers Installation ..................................................................... 53
Realtek HD Audio Driver Installation ................................................. 56
LAN Drivers Installation ..................................................................... 58
Intel® Management Engine Interface .................................................. 62
Intel® USB 3.0 Drivers ....................................................................... 65
IMPORTANT NOTE:
After installing your Windows operating system, you must install first the
Intel Chipset Software Installation Utility before proceeding with the
drivers installation.
IB908F User’s Manual 49
DRIVERS INSTALLATION
Intel Chipset Software Installation Utility
The Intel Chipset Drivers should be installed first before the software
drivers to enable Plug & Play INF support for Intel chipset components.
Follow the instructions below to complete the installation.
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
50
IB908F User’s Manual
DRIVERS INSTALLATION
3. When the Welcome screen to the Intel® Chipset Device Software
appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
IB908F User’s Manual 51
DRIVERS INSTALLATION
5. On the Readme File Information screen, click Next to continue the
installation.
6. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect.
52
IB908F User’s Manual
DRIVERS INSTALLATION
VGA Drivers Installation
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers.
2. Click Intel(R) Core(TM) i3/i5/i7 Graphics Driver.
IB908F User’s Manual 53
DRIVERS INSTALLATION
3. When the Welcome screen appears, click Next to continue.
4. Click Yes to to agree with the license agreement and continue the
installation.
54
IB908F User’s Manual
DRIVERS INSTALLATION
5. On the screen shown below, click Install to continue.
6. Setup complete. Click Finish to restart the computer and for changes
to take effect.
IB908F User’s Manual 55
DRIVERS INSTALLATION
Realtek HD Audio Driver Installation
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers.
2. Click Realtek High Definition Audio Driver.
56
IB908F User’s Manual
DRIVERS INSTALLATION
3. On the Welcome to the InstallShield Wizard screen, click Yes to
proceed with and complete the installation process.
4. The InstallShield Wizard Complete. Click Finish to restart the
computer and for changes to take effect.
IB908F User’s Manual 57
DRIVERS INSTALLATION
LAN Drivers Installation
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers.
2. Click Intel(R) PRO LAN Network Driver.
58
IB908F User’s Manual
3. Click Install Drivers and Software.
DRIVERS INSTALLATION
4. When the Welcome screen appears, click Next.
IB908F User’s Manual 59
DRIVERS INSTALLATION
5. Click Next to to agree with the license agreement.
6. Click the checkbox for Drivers in the Setup Options screen to select it
and click Next to continue.
60
IB908F User’s Manual
DRIVERS INSTALLATION
7. The wizard is ready to begin installation. Click Install to begin the
installation.
8. When InstallShield Wizard is complete, click Finish.
IB908F User’s Manual 61
DRIVERS INSTALLATION
Intel® Management Engine Interface
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers and then Intel(R) AMT 9.5 Drivers.
62
IB908F User’s Manual
DRIVERS INSTALLATION
2. When the Welcome screen to the InstallShield Wizard for Intel®
Management Engine Components, click the checkbox for Install Intel®
Control Center & click Next.
3. Click Yes to to agree with the license agreement.
IB908F User’s Manual 63
DRIVERS INSTALLATION
4. When the Setup Progress screen appears, click Next. Then, click
Finish when the setup progress has been successfully installed.
64
IB908F User’s Manual
DRIVERS INSTALLATION
Intel® USB 3.0 Drivers
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers.
2. Click Intel(R) USB 3.0 Drivers.
IB908F User’s Manual 65
DRIVERS INSTALLATION
3. When the Welcome screen to the InstallShield Wizard for Intel® USB
3.0 eXtensible Host Controller Driver, click Next.
4. Click Yes to to agree with the license agreement and continue the
installation.
66
IB908F User’s Manual
DRIVERS INSTALLATION
5. On the Readme File Information screen, click Next to continue the
installation of the Intel® USB 3.0 eXtensible Host Controller Driver.
6. Setup complete. Click Finish to restart the computer and for changes
to take effect.
IB908F User’s Manual 67
APPENDIX
Address
Device Description
000h - 01Fh
DMA Controller #1
020h - 021h
Interrupt Controller #1
040h - 043h
Timer
060h - 060h
Keyboard Controller
070h - 077h
Real Time Clock, NMI
081h - 091h
DMA Page Register
0A0h – 0A1h
Interrupt Controller #2
081h - 091h
DMA Controller #2
040h – 05Fh
SMBus Controler
2F8h - 2FFh
Serial Port #2(COM2)
3C0h- 3DFh
Graphics adapter Controller
D000 - FFFh
PCI-e Root Ports
3F8h - 3FFh
Serial Port #1(COM1)
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses which also becomes the identity of the device. The following
table lists the I/O port addresses used.
68
IB908F User’s Manual
APPENDIX
Level
Function
IRQ0
System Timer Output
IRQ1
Keyboard
IRQ3
Serial Port #2
IRQ4
Serial Port #1
IRQ8
Real Time Clock
IRQ10
SMBus Controller
IRQ19
SATA AHCI Controller
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
IB908F User’s Manual 69
APPENDIX
C. Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sorts of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user will
restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "6106"
//--------------------------------------------------------------------------int main (int argc, char *argv[]);
void EnableWDT(int);
void DisableWDT(void);
//--------------------------------------------------------------------------int main (int argc, char *argv[])
{
unsigned char bBuf;
unsigned char bTime;
char **endptr;
// char SIO;
printf("6106 watch dog program\n");
bTime = strtol (argv[1], endptr, 10);
printf("System will reset after %d seconds\n", bTime);
if (bTime)
{ EnableWDT(bTime); }
else
{ DisableWDT(); }
if (bTime > 0 && bTime < 256)
{
int A;
A=2;
do{
unsigned char result;
Set_6106_LD(0x08); //switch to logic device 8
result=Get_6106_Reg(0xF1);
gotoxy(1,12);
printf("Timer is %i \n",result);
}while(A!=1);
}
70
IB908F User’s Manual
APPENDIX
return 0;
}
//--------------------------------------------------------------------------void EnableWDT(int interval)
{
unsigned char bBuf;
Set_6106_LD(0x08); //switch to logic device 8
Set_6106_Reg(0x30, 0x01); //enable timer
Set_6106_Reg(0xF1, interval); //set timer
}
//--------------------------------------------------------------------------void DisableWDT(void)
{
unsigned char bBuf;
Set_6106_LD(0x08); //switch to logic device 7
Set_6106_Reg(0x30, 0x00); //enable timer
}
//---------------------------------------------------------------------------
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include "6106.H"
#include <dos.h>
//--------------------------------------------------------------------------unsigned int 6106_BASE;
void Unlock_6106 (void);
void Lock_6106 (void);
//--------------------------------------------------------------------------unsigned int Init_6106(void)
{
unsigned int result;
unsigned char ucDid;
6106_BASE = 0x4E;
result = 6106_BASE;
ucDid = Get_6106_Reg(0x20);
if (ucDid == 0x07) //6106
{ goto Init_Finish; }
6106_BASE = 0x2E;
result = 6106_BASE;
ucDid = Get_6106_Reg(0x20);
if (ucDid == 0x07) //6106
{ goto Init_Finish; }
6106_BASE = 0x00;
result = 6106_BASE;
Init_Finish:
return (result);
IB908F User’s Manual 71
APPENDIX
}
//--------------------------------------------------------------------------void Unlock_6106 (void)
{
outportb(6106_INDEX_PORT, 6106_UNLOCK);
outportb(6106_INDEX_PORT, 6106_UNLOCK);
}
//--------------------------------------------------------------------------void Lock_6106 (void)
{
outportb(6106_INDEX_PORT, 6106_LOCK);
}
//--------------------------------------------------------------------------void Set_6106_LD( unsigned char LD)
{
Unlock_6106();
outportb(6106_INDEX_PORT, 6106_REG_LD);
outportb(6106_DATA_PORT, LD);
Lock_6106();
}
//--------------------------------------------------------------------------void Set_6106_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_6106();
outportb(6106_INDEX_PORT, REG);
outportb(6106_DATA_PORT, DATA);
Lock_6106();
}
//--------------------------------------------------------------------------unsigned char Get_6106_Reg(unsigned char REG)
{
unsigned char Result;
Unlock_6106();
outportb(6106_INDEX_PORT, REG);
Result = inportb(6106_DATA_PORT);
Lock_6106();
return Result;
}
//------------------------------------------------------------------------------------
72
IB908F User’s Manual
Loading...