Thank you for purchasing the Ibanez MIMX series guitar amplifier. MIMX is a
digital modeling amp that boasts high-quality sounds delivered by 32-bit signal
processing. Read this manual thoroughly prior to using your amplifier in order to
get the most out of the functions available. Then keep the manual in a safe
place.
Important Safety Instructions
1) Read these instructions.
ENGLISH
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10)Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11)Only use attachments/accessories specified by the manufacturer.
12)Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or when unused
for long periods of time.
14)Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
WARNING - To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
8
S3125A
• “The Lightning Flash with arrowhead symbol within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product enclosure that may be of sufficient magnitude to constitute a
risk of shock to persons”.
• “The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product”.
Precautions during use
1) This product is capable of producing extremely high volumes. In some cases,this
could damage your hearing or cause other bodily impairment. You must be
careful of the volume when using this product.
2)
Always make sure that a speaker system of the correct impedance is connected.
3) Use this product with a power supply of the voltage that is printed on the rear
panel.
4) Place this product near the main power outlet, and ensure that the main power
plug can be easily disconnected from the main power outlet if any problem
should occur.
5) This device contains a fuse for protection. The fuse may be broken due to
external physical shock or because it has reached the end of its lifetime, but
since a broken fuse may indicate that a serious internal malfunction has occurred, please contact your dealer before replacing the fuse.
6) When you are not using it, leave the power turned off. As long as the MIMX is
connected to an electrical outlet, it is not completely insulated from the power
supply even if the power switch is turned off. If you will not be using the MIMX
for an extended period, leave the power cable disconnected.
7) Do not turn off the power switch or disconnect the plug from the AC outlet while
the device is operating. Doing so may cause malfunctions.
8) Do not stand on this device or place heavy objects on it. Doing so may cause
breakage or malfunctions.
Cautions regarding location
9) If you use the MIMX on top of a speaker cabinet, you must install this equip-
ment securely on the floor or wall. In particular if you're using two speaker
cabinets (i.e., a full stack), be sure to place the equipment on a flat and level
surface, and use security belts or similar fasteners to attach the equipment to
the floor or walls so that it cannot fall over.
10)Secure the provided power plug to mains socket-outlets that has a protective
ground terminal.
11) Do not place this device in locations where particularly low temperatures might
occur, such as walk-in coolers. The device may fail to operate correctly.
12)Do not place this device in locations subject to strong magnetic fields, such as
near a television or radio, or near any other device that emits electromagnetic
radiation. This device may fail to operate correctly under such conditions.
13)Do not place the device in locations subject to sudden temperature changes
If this device is in a cold room whose temperature is suddenly raised, condensation may form inside the device, causing it to fail to operate correctly.
14)Do not place the device in locations of excessive dust or vibration. Such conditions may cause damage or malfunction.
15)Depending on the location in which this device is placed, noise may occur in a
radio located nearby, or flickering or distortion may be seen in the screen of a
nearby television. If you suspect that this device is responsible for these conditions, turn off the power switch of this device. If this causes the radio or television to return to normal operation, try moving this device away from the radio
or television, or change the orientation of the radio or television.
ENGLISH
9
Safety precautions
You must carefully read these precautions before you begin using this device,
and use the device only as directed.
After you’ve read these precautions, keep them with the “Owner’s manual” and
the “Warrantee.”
Prevention of fire, electrocution, or injury
About the graphic symbols
ENGLISH
indicates a caution (including a danger or warning). The
specific content of the caution is indicated inside the triangle.
The graphic shown at left indicates a general caution, warning, or danger.
indicates a prohibition (something you must not do). The
specific content of the prohibition is depicted inside the symbol. The graphic shown at left indicates that you must not disassemble the unit.
indicates a compulsory action (something you are required
to do). The specific requirement is depicted inside the symbol.
Warnings
If the device emits smoke
Fire or electrocution may occur if you continue to use the device when it is
behaving abnormally, such as emitting smoke or an unusual odor. Immediately turn off the power switch, disconnect the plug from the AC outlet,
and contact the dealer from whom you purchased the device. Never attempt to repair the device yourself, since this can be hazardous.
If the device breaks
If you drop the device or if its cabinet is damaged, immediately turn off the
power switch, disconnect the plug from the AC outlet, and contact the
dealer from whom you purchased the device. Fire or electrocution may
occur if you continue using the device in this condition.
If a foreign object enters this device
If a metallic or flammable foreign object should enter the interior of this
device through a jack or other opening, immediately turn off the power
switch, disconnect the plug from the AC outlet, and contact the dealer
from whom you purchased the device. Fire or electrocution may occur if
you continue using the device in this condition.
Do not disassemble or modify the device
Do not open the cabinet of this device. This device contains high-voltage
components, and touching them may produce electrical shock. Contact
your dealer if interior inspection or servicing is required.
Do not modify this device. Doing so may cause fire, electrical shock, or
malfunctions.
Do not place water or chemicals on the device
To avoid the risk of fire or electrical shock, do not place flower vases,
drinks, cosmetics, or containers of chemicals or water on top of this device.
Unplug from the AC outlet if lightning occurs
If lightning occurs nearby, turn off the power switch, disconnect the plug
from the AC outlet, and stop using the device. Lightning can cause fire or
electrical shock.
Do not place the device near flame or heat
Do not allow this device or its power cable to be near heating equipment.
Such a situation poses a risk that the cabinet or the power cable sheathing may melt, causing fire or electrical shock.
Do not use the device at high volume levels for a
long time
Using the device at high volume levels through headphones or speakers
for a long time may cause permanent hearing loss depending on the
output volume setting.
Do not place the device in locations of high humidity
Do not use this device in locations of high humidity such as near a bath or
humidifier, or in the rain, or near a body of water. Doing so may cause fire
or electrical shock.
10
Do not block the cooling vents
Since the rear of this device functions as a cooling vent, you must leave
sufficient space between it and the wall. Blocking the cooling vent will
cause heat to be trapped inside the device, possibly causing fire.
Do not place the device in locations of high temperature
Do not place this device in locations of high temperature, such as in direct
sunlight or near equipment that produces heat, such as a stove or heater.
Doing so will cause the internal temperature to rise, possibly causing fire.
Do not subject the device to oil spatters or steam
Do not place this device where it might be subjected to oil spatters or
steam. This could cause fire or electrical shock.
Use this device only with an AC outlet of the
correct voltage
You must use this device only with an AC outlet of the correct voltage as
marked on the device itself. Fire or electrical shock may occur if you use
this device with an AC outlet of the wrong voltage.
Do not operate with wet hands
Do not connect or disconnect the power cable while your hands are wet.
You risk electrical shock if you do so.
Handle the plug with caution
When unplugging the cable, be sure to grasp the plug itself. If you unplug
the power cable by pulling the cable itself, you risk damaging the cable,
possibly causing fire or electrical shock.
Do not use “octopus-like” connections
Do not use branching extension cords, power strips, or branching sockets
to create “octopus-like” connections from an AC power outlet. Doing so
may cause fire or electrical shock.
Use this device only in the country where you
purchased it
This device is designed for the AC power supply voltage of the country in
which you purchased it; you cannot use it outside the country.
Cautions
Disconnect the power cable if you will be away
If you won’t be using the device for an extended period of time, disconnect the plug from the AC outlet for safety.
Do not drop the device or subject it to physical
impact
Do not drop this device or subject it to strong physical impact. Doing so
may cause breakage or malfunctions.
Do not place the device in an unstable location
Do not place this device in an unstable location, such as on an unsteady
stand or at an angle. It may become unbalanced and tip over or fall, causing damage or injury.
ENGLISH
Handle the power cable with caution
Do not allow the power cable to be scarred, damaged, modified, excessively bent, pulled, twisted, or bundled. If heavy objects are placed on the
power cable or if it is subjected to heat, it may be damaged, possibly
causing fire or electrical shock. Please contact your dealer if the power
cable becomes damaged.
11
Tutorial
This section takes you through step-by-step explanations of how to make
connections to your amp, create sounds, save or reset the sounds you've
created, and use rhythm patterns. Once you've followed along with these
explanations, you'll understand nearly all of the operations of the MIMX.
The illustrations appearing here are taken from the control panel of the
MIMX 150H.
1. Connections
ENGLISH
1)-a Carefully read the cautions for use, and then set up your amp. Next
use the included power cable to connect the rear panel 12 AC INPUT to
an electrical outlet.
Note: The sound (particularly the low-frequency response) of the amp
will change according to the location and conditions in which you set up
the amp.
1)-b If you're using the MIMX 150H, connect 14 SPEAKER OUT to the
4Ω input jack of your speaker cabinet. Use a speaker cable to make this
connection. On Ibanez IS series speaker cabinets, there are two input
jacks. Use the one marked MONO 4Ω.
2) Connect your electric guitar to 1 INPUT. Use a shielded cable to
make the connections.
3) If you're using a compact effect device, use a shielded cable to connect it between your guitar and amp.
4) Make sure that 10 MASTER volume is set to 0, and turn on the
POWER switch. The startup animation will appear, and the amp is ready
to use.
Note: When you're finished using the amp, make sure that 10 MASTER
volume is set to 0 and then turn off the 11 POWER switch.
● If you're using the IFC2
By connecting the optional IFC2 (Sold separately), you can access the
additional five pedal effects. For details on making connections, refer to
the IFC2 operating manual.
12
2. Creating your sound
Let's get started creating some sounds. In this example, we're going to
use the number 11 drive pattern PSYCHO.
1) In the 3 Memory section, click the MANUAL switch.
This selects manual mode, where all sound settings will be according to the actual position of the controls.
2) Raise the 10 MASTER volume to a position between 8 o'clock
and 12 o'clock.
Set the 2 Preamp section as follows.
This will produce a very tight distortion sound. Now let's add some effects.
4) First we'll add the 7 MODULATION effect. Make the following settings.
FX TYPE&PARAMETER:FLANGER 15
FX MIX LEVEL :20
TAP TEMPO :10
*The above illustration shows the
MIMX 150H.
11
5) Next we will add the 8 DELAY&REVERB effect. Make the following
settings.
FX TYPE&PARAMETER:REVERB HL 10
FX MIX LEVEL :30
TAP TEMPO :1
*The above illustration shows the
MIMX 150H.
You'll notice that the sound has become more spacious. Now go ahead
and try creating your own sounds in the same way. Next we will learn
how to save a sound you've created.
Note: This amp is capable
of producing extremely loud
volumes. Please set the
MASTER volume in a way
that will not inconvenience
other people nearby.
* Refer to "About the TAP
switch" later in this manual.
Note: The TAP switch will respond
even to a light touch. Striking it with
excessive force will damage it so
please tap lightly.
10
3. Saving a sound you created
In this section you'll learn how to save a sound you've created. We'll
save your new sound in bank A, channel 1.
* For details on initializing the memory, refer to 5. Factory reset
1) Make sure that the 5 Display indicates M. Then, hold down the switch
marked "1" for three seconds or longer. When the settings have been
saved, the 5 Display will indicate A1, and will blink.
Note: Each channel consists of two banks, A and B. If you
want to save settings in bank A, channel 1 as described in this
tutorial after creating your sound in manual mode, you must
first click "1", make sure that you're currently in bank A, and
then click the MANUAL switch once again to return to manual
mode before you proceed with the following steps.
Hold down for three seconds or longer.
A sound you create in manual mode as described here can be saved in
any channel. A sound you create in each bank can be saved in a channel within that bank.
Here's an example.
2) Up to this point, we've used bank A, channel 1 to create a sound, but
now we're going to slightly adjust the position of each control and save
the result in bank A, channel 2. Perform the following steps.
4. Using rhythm patterns
This section explains how to use rhythm patterns.
1) We'll start by playing a rhythm. Click the ON/OFF switch. The TAP
switch will blink, and you'll hear drum sounds.
Note: Use the RHYTHM knob to adjust the volume appropriately.
2) Next we'll change the pattern. Press + or - until the 5 Display indicates 16.
3) Let's make the tempo a bit faster. Click the TAP switch several times
at a consistent rhythm until the 5 Display indicates 120.
Play a rhythm pattern Change the rhythm pattern Change the rhythm speed
You can use rhythm patterns by following the procedure described above.
5. Factory reset
This section explains how to initialize the amp to the factory-set condition.
1) While holding down the MANUAL switch as shown in the illustration
below, turn on the 11 POWER switch. The 5 Display will indicate AL.
2) If you press the MANUAL switch in this state, all data will return to the
factory-set condition.
3) If you decide to cancel without resetting, operate any control other
than the MANUAL switch. You will exit factory reset mode.
ENGLISH
Edit the sound of
bank A, channel 1
Hold down for three seconds
or longer
The sound is saved
in bank A, channel 2
By saving your edited sound in another channel, you'll be able to compare the two sounds. Next we're going to try using rhythm patterns.
While holding down the
MANUAL switch, turn on
the POWER switch.
Preamp section: This controls the tone of the guitar. Details for each
section are as follows.
1)
AMP SELECTION: This knob lets you select from eleven types of preamp
model. For details, refer to the section describing the various amps.
2) GAIN: This control knob adjusts the gain. The range of adjustment
ENGLISH
will depend on the AMP SELECTION setting. According to the GAIN
level, the 5 Display will indicate a value between 0 and 100.
3)
Equalizer: These are the control knobs for the levels (BASS, MIDDLE,
TREBLE) of the three-band equalizer. The adjustable range and the function will both differ according to the AMP SELECTION setting. According
to the level, the 5 Display will indicate a value between -15 and 15.
4)
VOLUME: This is the control knob for the output level from the preamp.
According to the VOLUME level, the 5 Display will indicate a value between 1 and 50. The output level will be affected by the type of amp
you've selected, the gain level, and the equalizer level. You can use this
control to keep the level consistent between channels, as well as to specify
the desired level. The final volume is set by the 10 MASTER volume.
3
Memory section: To save a sound you created, hold down the switch of
the desired save-destination channel for three seconds or longer. Details are described below.
1)
MANUAL: This switch selects manual mode, where all sound settings will
reflect the actual position of the controls. The 5 Display will indicate M.
2) Channels (1-5): These switches choose one of five channels in which
you can store your own settings. There are two banks (A and B), letting
you store a total of ten sounds. As an alternative to selecting these from
the front panel, you can connect the optional IFC2(sold separately) foot
controller and switch channels using your foot. The 5 Display will indicate the channel number (1-5).
3) A/B bank switch: There are two banks, each containing five channels.
4
Drum section: You can use fifty different rhythm patterns.
1) RHYTHM knob: This knob controls the drum volume.
2) ON/OFF: This switch turns the rhythm pattern on/off.
3) -/+: These switches let you choose from the fifty different rhythm patterns. For details on each pattern, refer to SPECIFICATIONS.
*
The above illustration
shows the MIMX 150H.
14
4) TAP switch: This controls the rhythm speed in a range
of 40 bpm to 199 bpm.
5
Display: Various operations are shown here.
6
TUNER ON/OFF: The MIMX provides a chromatic tuner. The illustrations
below show what the display will indicate when the tuner is operating.
Lit to indicate a flat
Movement
of display
When the pitch is lowWhen the pitch is high
7
MODULATION section: Here you can control four types of modulation
When the pitch is correct: E-flat
Movement
of display
effects.
1) FX knob: This control knob selects from four types of modulation
effect. Each is as follows.
a CHORUS: This effect creates a rich sound by overlaying
the sound and modulating it. By controlling the FX knob
you can vary the modulation depth in a range of 0 to 100.
b FLANGER: This effect applies modulation and sweep to
the sound. By controlling the FX knob you can vary the
modulation depth in a range of 0 to 100.
c VIBRATO: This effect applies vibrato. By controlling the
*The above illustration shows the
MIMX 150H.
FX knob you can vary the modulation depth in a range of
0 to 100.
d STEP: This effect varies the sound in a stepwise manner. By controlling the FX knob you can vary the modulation depth in a range of 0 to 100.
2) MIX knob: This controls the mix level of the modulation effect in a
range of 0 to 100. At a setting of 0, the effect will be off; no modulation
effect will be applied.
3) TAP switch: This controls the modulation speed of the modulation
effect in a range of 1-50. The following table shows the modulation speed
that can be controlled by the TAP switch for each mode.
For details on TAP, refer to "To use the TAP switch successfully".
Note: If you're using the 9 PEDAL FX section's PEDAL PITCH effect, you
won't be able to use the MODULATION section's effects.
DELAY & REVERB section: Here you can control four different
Delay&Reverb effects.
1) FX knob: This control knob selects one of four Delay&Reverb effects.
These effects are listed below.
*The illustration
shows the MIMX
150H.
2) MIX knob: This controls the mix level of the Delay&Reverb effect in a
range of 0 to 100. At 0 the effect is off, and there will be no Delay&Reverb
effect.
3) TAP switch: When using DELAY or ECHO, this controls the delay
time. When using REVERB, this controls the length of reverberation.
The following table shows the delay time and reverb time that can be
controlled using the TAP switch in each mode.
For details on TAP, refer to "To use the TAP switch successfully".
Note: You can't use REVERB while using the 4 Drum section.
9
PEDAL FX section: You can control pedal-type effects by using a optional IFC2(sold separately) foot controller. For details, refer to "More
about the foot controller".
1) SELECT switch: This selects one of five types of pedal effect. These
effects are as follows.
*The illustration shows
the MIMX 150H.
a DELAY: This effect adds a delayed copy of the original
sound, somewhat like a musical "round". Use the FX
knob to vary the feedback in a range of 0 to 40.
b ECHO: This effect produces a warmer DELAY effect.
Use the FX knob to vary the feedback in a range of 0 to 40.
c REVERB HL: This reverb simulates the acoustics of a
large space such as a concert hall. Use the FX knob to vary
the character of the reverberation in a range of 0 to 10.
d REVERB RM: This reverb simulates the acoustics of a
small space such as a room. Use the FX knob to vary
the character of the reverberation in a range of 0 to 10.
a VOL PEDAL: This is a volume pedal that lets you control the volume using your foot.
b RING MOD: This effect gives a metallic character to
the sound.
c AUTO RESO: This effect varies the resonant frequency
1~30
according to the strength of your picking.
d WAH WAH: This is a wah-wah effect.
e PEDAL PITCH: This effect lets you vary the pitch in
real time.
2) Control knob: This knob controls the effect of the 9 PEDAL FX section. The effects available in each mode are as follows.
Minimum positionMaximum position
3) Foot switch jack: You can use the foot switch by connecting the separately sold IFC2.
4) Foot pedal jack: You can use the 9 PEDAL FX section by connecting
the optional IFC2(sold separately).
10
MASTER volume: This controls the final output that is sent to the speaker.
11
POWER switch: This is the power switch for the amp.
12
AC INPUT: Connect the included power cable here.
13
LINE OUT (MIMX 150H): This is a line-level output jack.
14
SPEAKER OUT (MIMX 150H): This is a speaker output jack. Use a
speaker cable to connect this to either a 4Ω or 8Ω speaker system.
Note: If you use a speaker system whose impedance is less than 4Ω,
(e.g., a 2Ω speaker system), the power amp will overheat, causing a
protection circuit to engage, and the correct output will not occur.
15
HEADPHONES (MIMX65): This is an output jack for headphones.
16
CD INPUT (MIMX65): This is a line-level input jack. You can connect a
portable CD player or MP3 player here.
ENGLISH
15
AMP SELECTION
The AMP SELECTION dial lets you choose from eleven types of preamps.
Of the numerous guitar amps that exist, Ibanez has focused on the distinctive sounds of ten classic amplifiers that are particularly admired by
many guitarists. Everything from the guitar input to the speaker output
has been analyzed and stored as a preamp. The MIMX is designed so
that sounds similar to these amps can be easily obtained. The EQ for
each preset takes into consideration the sampled amplifier's overall sound
ENGLISH
including the response when things such as "Presence," "Bright," "Resonance" or "Deep" Controls are engaged (or not) allowing each model to
obtain startlingly detailed snapshots of classic tones. These are not exact replications by any means but more a "flavor" if you will. Finally a
tight, heavy, and smooth Ibanez original sound is provided as Selection
Number 11. It is appropriately named, "Psycho."
PLEASE NOTE: In the following pre-amp descriptions, names of nonIbanez products are used to give you understandable and familiar tonal
references and to show the kinds of amp sounds that inspired the MIMX
preamp settings. These references and comparisons to non-Ibanez products are entirely subjective. Ibanez does not make any claim whatsoever
that the MIMX pre-amps are exact tonal representations of the amps
they reference or are compared to. That said, we think you're going to
love what you hear with the vast selections of tones you can achieve
with your new MIMX.
16
60s Clean:
This preset was created to bring to mind the sound of one of the classic
amps made by Fender®, the '65 Twin Reverb®, being played through its
NORMAL Channel with the BRIGHT Switch OFF. Mentioning the clean
sounds of the '60s will bring this amp to anyone's mind. The sound design of this preamp emphasizes the sparkling crisp high end and solid
lows reminiscent of the Classic '60s sounds, but it still has a pleasantly
unique sound all its own.
Jazz Combo:
This selection was inspired by the Roland® JC-120, famed for its ability
to convey the straightforward tone of the guitar itself when played through
CHANNEL 1 with the BRIGHT Switch OFF and softened overall tonally.
This pre-amp's wide range and uncolored sound over a wide range from
low to high is a good match for effect processors, making this a highly
versatile selection.
70s Brit:
This is a sound we find reminiscent of the classic Marshall® "JCM800
2203" combined with the overdrive obtained when the Ibanez®
TUBESCREAMER®/TS-9 is employed as a drive booster. From solid
chording to glistening solos, this preamp covers a wide range of creative
sounds.
Brit Blues:
The history of the VOX® "AC30" parallels a broad stream of musical
history including blues, rock, and pop. Since its fame continues undiminished to this day, and it is still loved by numerous musicians, we thought
a preamp influenced by this type of sound was simply a no-brainer. When
creating the MIMX flavor we added more gain with a distinctively crisp
midrange and tightness so as to in our mind enhance the classic tone.
The nuances of your picking will be transmitted faithfully, allowing you to
play with a wide variety of tones.
US Blues:
We find this selection very reminiscent of the Fender® "Hot Rod Deville™"
played through the DRIVE channel with BRIGHT set to NORMAL, and
MORE DRIVE turned ON. The MIMX has tightened up low-end of that
sound and switched the EQ sets to shelving style. The particular attrac-
tion of this selection is a bright sound with a distinctively hard resonance.
From a lower gain sound that emphasizes the hard tonal character to
the great sounding drive you get by maxing out the gain, this preamp
delivers a broad palette of tones.
Rock:
This selection is our take on the sound of the "Ecstasy 101B EL34 Version," a multi-function tube amp made by the Bogner Corporation, which
is famous for its boutique amps. The settings response provides an improved dynamic range from low gain to high gain with more EQ control
level. While notable for its edged tone, this setting will give you a wide
variety from sweet and clean to hard chording sounds, as well as sustaining overdrive sounds.
Hard Rock:
First only offered to a few as custom-made amps, Soldano's® "SL0100" went on to achieve wider success and reknown. We created this
selection to be similar to the sound of the SLO-100's OVERDRIVE channel with the BRIGHT switch at NORMAL but reduced the possibility of
feedback with an overall tension and tightness. We believe the high gain
sound is particularly good and is an ideal choice for leads or heavy riffs.
Guitar God:
Here you have our idea of what the Peavey® "5150 II®" sounds like. In
creating this MIMX preamp, we listened to both the actual Peavey amp
as well as the audio sources used on a CD in order to reproduce the
sounds that, to our ears, are reminiscent of those recorded. The tight low
end is nice for riffs that intermingle muted notes, and the distortion will
make your sustained solos memorable.
90s Brit:
This preamp was also designed by referring to both the amp, in this case
the Marshall® "JCM2000 DSL100" amp, and to the actual audio CD
sources of a band who used this amp. Our take on this sound produces
a distortion component that is rough, but the sound is tight and well
defined with good separation of notes, making it usable for everything
from sparkling arpeggios to flashy riffs. Your guitar sound will be guaranteed to stand out, even in a loud band.
LA Heavy:
The Mesa/Boogie® "Dual Rectifier® Solo Head" has influenced numerous musicians of heavy styles. This preamp brings you our interpretation of a collage of the classic sounds of a model introduced in 1989 that
has defined modern heavy guitar tone. Our version provides the distortion sound of the original 6L6 power tubes through the RED channel
with the power supply in BOLD mode, using the silicon diode rectifier
mode finally played through an Ibanez® Thermion® TN412A four-twelve
cabinet. The result is a monstrous low end with good crunch.
Psycho:
This is an original Ibanez sound, designed to capture the mainstream of
today's heavy rock scene. It features a tight and sharp low end, with
superb crispness. By adjusting the EQ settings, you can use this sound
for any style of music.
* With the exception of Ibanez®, TUBESCREAMER® and Thermion®,
company names and product names appearing in this manual are
the trademarks or registered trademarks of their respective owners,
and have no affiliation with Ibanez.
Fender®, Twin Reverb®, Hot Rod Deville™ are registered trademarks
or trademarks of the Fender Musical Instruments Corporation.
Roland® is a registered trademark of Roland Corporation.
Marshall® is a registered trademark of Marshall Amplification PLC.
VOX® is a registered trademark of VOX R&D limited.
Soldano® is a registered trademark of Soldano Custom Amplification.
Peavey® is a registered trademark of Peavey Electronics LTD.
5150 II® is a registered trademark of E.L.V.H., Inc.
Mesa/Boogie® and Dual Rectifier® are registered trademarks of
Mesa/Boogie, Limited.
ENGLISH
17
Factory Presets
These are the sound settings that are assigned to each channel A1-B5
when the MIMX is shipped from the factory. With a single click of a button, you can obtain the MIMX's distinctive combinations of sound and
effects.
A1: Immortal Shred
AMP SELECTION: Psycho
This preset is ideal for the speedy riffs that are typical of the slash metal
ENGLISH
or death metal bands in today's music scene. The mid-range is cut to
emphasize the high and low ranges, and a firm and robust sound is
created by raising the bass without excessively reducing the middle.
A2: Shrapnel Heroes
AMP SELECTION: Psycho
This preset can be used for guitar solos in a broad range from hard rock
to heavy metal. The EQ is relatively flat. If you add a fairly fast delay this
preset will give you a nice sound for soloing.
A3: Cruel Heaviness
AMP SELECTION: 90s Brit
This preset is for riffs that emphasize rhythm. It is ideal for low-tempo
songs and the boosted low range will give you a heavy distortion sound
that will pull together the sound of your band. This is ideal for the loud
rock sounds of today's music scene.
A4: Legend of the Beast
AMP STYLE: Hard Rock
This is a solo guitar preset for that classic 80's Metal Sound. This preset
has a sound character that is suggestive of the Golden Age of Metal as
typified by numerous British and LA metal bands.
A5: Emotional Clean
AMP STYLE: 60s Clean
This preset gives you thick lows, a brittle attack, and reverb to create a
warm atmosphere. By using a single-coil pickup you can produce a vintage brilliant sound. By lowering the mix level of the reverb effect you
can emphasize the sense of attack.
18
B1: Sounds of the Right Hand
AMP SELECTION: Guitar God
This preset is ideal not only for heavy and tight riffs but also leads. The
distortion obtained by raising the GAIN to the maximum and a punchy
mid-range are a good match for humbucking pickups. A flanger is lightly
applied to produce a sense of drive, and delay is added to create spatial
effect.
B2: Purple Tone
AMP SELECTION: Rock
This is a high gain setting that strongly cuts the low range and adds a
distinctive character to the mid-range. By using a single coil pickup, you
can recapture the sound of the mid 70's. As you raise the MIDDLE control, the sound will take on a classical atmosphere --- adjust to your taste.
To take full advantage of this sound, play the hard rock riffs that were
revolutionary at the time and have now become the origin of today's
heavy rock.
B3: Crystal Clean
AMP SELECTION: Jazz Combo
This preset was designed to produce sparklingly clean and crystal clear
sounds. It is most suited to the hard rock and heavy metal "Power Ballads" of the 80's and 90's. Try playing it using single-coil pickups, either
the center pickup or a combination of the neck/middle pickups. Raise
the effect mix level to get a more lavish sound.
B4: Solo DNA
AMP SELECTION: Rock
This preset was created for you to play those shredding solos made
famous by the guitar gods of the 80's! It's a setting that's great for going
wild with your musicality. Make free use of string bending, dive bombing,
pinch harmonics, sweep arpeggios and express your imagination.
B5: Samurai Edge
AMP SELECTION: 70s Brit
This preset is a good choice for comping or bluesy riffs played with a
single coil pickup. It has just the right amount of distortion to accentuate
the nuances of your picking, and has a nice crisp high end. Adjust the
amount of reverb to your taste.
Proper Use of the Tap Switch
The MIMX provides a TAP switch that you can use to control the speed
of the effects and the rhythm. You might find this somewhat unfamiliar in
the beginning, but soon you'll be able to use it easily and intuitively.
By clicking(tapping) this switch several times(not just twice), you can
specify the desired speed. As you continue clicking, the average interval
will appear in the 5 Display. A good rule of thumb for use is to lightly tap
the switch in tempo for a complete measure of the passage that you are
about to play.
For those interested in the "technicals", a detailed explanation of how
the TAP function detects the average tempo is given below.
A moving average
A method called "moving average" is used to determine the tempo speed
via the TAP switch. For example if you want to set the drum tempo to
120 BPM, it's quite difficult to specify the precise tempo simply by click
the TAP switch only twice.
Four-value moving average (here we will use four values for our explanation)
The average value of the four most recent operations of the TAP switch is used as
the value. This allows any inaccuracies of your actual operation to be absorbed.
Operated
1125bpm2115bpm3130bpm4109bpm
value
Output
value
1
125bpm120bpm121bpm119bpm123bpm
(1+2)
2
Two-value moving average
You will need to press the TAP switch at an accurate rhythm
so that the interval between the first and second presses of
the TAP switch is 60/120 seconds = 0.5 seconds.
(1+2+3)3(1+2+3+4)4(2+3+4+5)
The MIMX uses a seven-value moving average. By marking the beats
with the TAP switch, you can obtain a more accurate tempo setting.
5131bpm
4
About the "currently-edited" indication of the center display
The MIMX has a "currently-edited" LED that will light as shown in the
illustration below.
The MIMX provides analog-type rotary
controls in the interests of operability.
"Currently-edited"
LED
Knob
position
Position of actual
sound
Display will light to indicate this. When you move the control to the position that corresponds to the memorized value, the "currently-edited" indication will disappear. This is the value that is stored in the selected
channel.
Here's an example.
1) Click A1.
2) Move the GAIN control to 12 o'clock. The
Display will indicate 50, and the dot will light. This
indicates that the gain has been edited, and is different from the gain value in memory.
3) Move the GAIN control to the maximum position. The 5 Display will indicate 100, and the dot
will go dark. This indicates that the gain value in
memory is shown in the 5 Display.
* This function is provided for all controls. You can use it to compare the
stored control values with the current value, or to check the contents that
are stored in each channel.
* If you click the MANUAL switch to select manual mode, the position of
every control will correspond to the actual value that determines the sound.
However when you click a channel
switch A1-B5 to recall the stored settings, the sound settings recalled to the
front panel control knobs will not necessarily correspond to the physical
position of the knobs. For this reason,
when you click a channel switch to recall a memory, and then move a control to a position that differs from the
memorized value, the "currently-edited" LED in the lower right of the
5
19
ENGLISH
5
More about the foot controller
You can use the separately IFC2(sold separately) as a controller for the
MIMX. If you connect the IFC2, you'll be able to use the 9 PEDAL FX
section, and use the foot switches to switch channels.
ENGLISH
a
e
d
b
f
c
A
B
Operations
a
Pedal: Controls the pedal effect that's selected on the amp.
b
Up switch: Switches to the next higher memory than the currently
selected memory. (Does not operate in manual mode.)
c
Down switch: Switches to the next lower memory than the currently
selected memory. (Does not operate in manual mode.)
d
Foot switch jack: Connect this to the amp in order to use the foot
switches.
e
Pedal effect jack: Connect this to the amp in order to use the pedal
effect. A circuit inside the IFC2 allows the MIMX to recognize that
the pedal is connected.
Mode switch: This switch determines how the pedal will operate.
f
Set this as appropriate for your playing style.
A
The effect will remain on even when the pedal is in the minimum
position (fully returned toward yourself).
The effect will turn off when the pedal is in the minimum position
B
(fully returned toward yourself).
Press b c simultaneously to activate the tuner.
20
Troubleshooting
First check that your shielded guitar cable, speaker cable, and power cable are
connected correctly. If possible, use a tester to check the cable or try using an
alternate cable or amp to verify your cable’s condition.
1. The power supply cannot be switched on.
• Check that the power cable has been connected correctly.
• Try plugging it into a different socket and see if the same problem occurs.
2. The power supply can be switched on, but no sound is
heard.
• Check that the guitar has been connected correctly.
• Remove any external components connected to the effects loop and between
the guitar and the amplifier and check to see if any sound is heard.
• Use a different shielded cable and check to see if any sound is heard.
• Check to see if the volume on the guitar is set to “0”.
• Use a different guitar and see if any sound is heard.
• Check to see if the volume on the amplifier is set to “0”.
• Check to see if the headphones are connected.
• Is there still no sound when you raise the master volume?
• Check to see if you're using the separately sold IFC2 foot controller as a volume
pedal, and the pedal is in the fully returned position (toward yourself).
3. Noise is heard.
• Check to see if anything in the immediate vicinity is resonating or banging against
the amplifier to produce the noise.
• Check to see if the plug cover on the shielded cable is loose.
• Make sure that the action (string height) of your guitar is set correctly.
• Use another guitar, effects or other external components, and cable to see if the
same noise is produced.
4.No sound when you connect a CD.
• Make sure that the volume of the CD player is not turned to 0.
• Make sure that the cable is connected correctly.
• Try using another cable and see whether any sound is heard.
5. The CD sounds wrong.
Does the cable you’re using have a stereo plug? Could you be using a monaural plug?
6. No sound is produced in the headphones.
• Check that the headphones are connected correctly.
• Connect another set of headphones and see if sound is produced.
7. No drum sounds.
• Check to see if the drum volume is set to 0.
• Check to see if the master volume is set to 0.
• Check to see if headphones are connected.
8. Modulation effect is not applied.
• Check to see if the mix level is set to 0.
• Check to see if you're using the tuner built into the MIMX.
• Check to see if you're using the separately sold IFC2 foot controller to control
PEDAL PITCH.
9. Delay effect is not applied.
• Check to see if the mix level is set to 0.
• Is there any change when you operate tap?
• Check to see if you're using the tuner built into the MIMX.
10. Reverb effect is not applied.
• Check to see if the mix level is set to 0.
• Check to see if there any change when you operate tap.
• Check to see if you're using the Drum function.
• Check to see if you're using the tuner built into the MIMX.
11. Can't use the pedal effect.
• Is the separately sold IFC2 foot controller connected?
• Are you using the cable included with the IFC2?
• Check to see if you're using the tuner built into the MIMX.
In case of defects
This product has passed exhaustive inspections before being shipped from the
factory. Ensure that the above procedures are carried out when a problem is
thought to exist. Contact your dealer in the unlikely event that an abnormality
occurs during use. Also, ensure that the symptoms of the problem are explained
in detail when requesting repair in order to facilitate swift handling.
Because of improvements to this product, the specifications may change without notice.
Vielen Dank für den Erwerb des Gitarrenverstärkers der MIMX-Serie von Ibanez.
MIMX ist ein Digital-Modeling-Amp mit qualitativ hochwertigen Sounds durch
die 32-Bit-Signalverarbeitung. Lesen Sie diese Anleitung sorgfältig durch, um
das Beste aus den verfügbaren Funktionen herauszuholen. Bewahren Sie die
Anleitung an einem sicheren Ort auf.
Vorsichtsmaßnahmen für den Gebrauch
1) Lesen Sie die Vorsichtsmaßnahmen in dieser Anleitung.
2) Heben Sie die Vorsichtsmaßnahmen dieser Anleitung zum späteren
DEUTSCH
Nachschlagen gut auf.
3) Beachten Sie alle Vorsichtsmaßnahmen.
4) Befolgen Sie die in dieser Anleitung gegebenen Anweisungen.
5) Benutzen Sie für die Reinigung Ihres Amps ein trockenes, weiches Tuch.
6) Dieses Produkt ist in der Lage, extrem hohe Lautstärken zu erzeugen. In einigen
Fällen kann dies zu Hörverlust oder anderen körperlichen Schäden führen. Seien
Sie bei Gebrauch dieses Produktes vorsichtig mit zu hohen Lautstärken.
7) Achten Sie immer darauf, dass Lautsprecher der richtigen Impedanz
angeschlossen werden.
8) Verwenden Sie dieses Produkt mit einer Stromversorgung der auf der Rückseite
angegebenen Spannung.
9) Achten Sie darauf, dass das Stromkabel nicht geknickt oder getreten wird,
besonders in Nähe des Steckers bzw. der Steckdose.
10)Stellen Sie dieses Produkt in der Nähe der Steckdose auf, und vergewissern
Sie sich, dass sich der Netzstecker leicht aus der Steckdose ziehen lässt, falls
ein Problem auftauchen sollte.
11)Verwenden Sie nur das beiliegende Zubehör oder solches, das die
Anforderungen des Herstellers erfüllt.
12)Dieses Gerät enthält eine Sicherung zum Schutz der elektrischen Schaltkreise.
Es kann sein, dass die Sicherung aufgrund von Stößen, Überschreitung der
Lebensdauer usw. bricht, da aber eine durchgebrannte Sicherung zumeist auf
interne Fehlfunktionen hinweist, wenden Sie sich an Ihren Händler, bevor Sie
die Sicherung ersetzen.
13)Überlassen Sie jegliche Reparaturen Fachpersonal, das vom Vertrieb dafür
autorisiert wurde. Eine Inspektion oder Reparatur ist erforderlich, wenn das
Netzkabel oder der Stecker beschädigt ist, wenn Flüssigkeiten aus dem Gerät
herauslaufen, wenn ein fremder Gegenstand in das Innere des Gerätes
eingedrungen ist, wenn das Gerät durch Wasser oder Regen nass geworden
ist, wenn das Gerät versehentlich fallen gelassen wurde oder wenn es nicht
mehr normal funktioniert.
14)Wenn Sie das Gerät vorübergehend nicht benutzen, schalten Sie es aus. So
lange der MIMX an einer Netzsteckdose angeschlossen ist, ist er nicht vollständig
von der Stromversorgung getrennt, auch dann, wenn das Gerät ausgeschaltet
ist. Wenn Sie den MIMX für längere Zeit nicht benutzen werden, ziehen Sie
zusätzlich das Netzkabel aus der Steckdose.
15)Schalten Sie den Netzschalter nicht aus, und trennen Sie nicht das Netzkabel
von der Steckdose, solange das Gerät in Betrieb ist.
16)Stellen Sie sich nicht auf das Gerät, und legen Sie keine schweren Objekte auf
dem Gerät ab. Andernfalls kann das Gerät zerbrechen, oder Störungen können
auftreten.
36
Vorsichtsmaßnahmen bezüglich des Standorts
17)Wenn der MIMX auf einer Lautsprecherbox aufgestellt wird, muss das Gerät
sicher am Boden oder an der Wand befestigt werden. Insbesondere wenn zwei
Lautsprecherboxen verwendet werden (d.h. ein voller Stack) muss das Gerät
auf flacher und ebener Oberfläche aufgestellt werden, und Sicherheitsgürtel
oder ähnliche Befestigungen müssen verwendet werden, um das Gerät auf dem
Boden oder an Wänden zu befestigen, um Umkippen zu verhindern.
18)Stellen Sie dieses Gerät nicht an Standorten auf, wo besonders niedrige
Temperaturen sind. ( Sounds much friendlier than the other word.), wie z. B.
begehbare Kühlräume. Das Gerät funktioniert dann möglicherweise nicht mehr
ordnungsgemäß.
19)Stellen Sie das Gerät nicht an Standorten auf, die starken magnetischen Feldern
ausgesetzt sind, wie z. B. in der Nähe von Fernsehgeräten oder Radios oder in
der Nähe von anderen Geräten, die elektromagnetische Strahlungen abgeben.
Unter solchen Bedingungen können Fehlfunktionen auftreten.
20)Stellen Sie das Gerät nicht an Standorten mit plötzlichen Temperaturänderungen
auf.
Wenn dieses Gerät in einem kalten Raum steht, dessen Temperatur plötzlich
erhöht wird, kann im Inneren des Geräts Kondensierung auftreten, was zu
Fehlfunktionen führen kann.
21)Stellen Sie das Gerät nicht an Standorten mit übermäßig viel Staub oder
Vibrationen auf.
Solche Bedingungen können Schäden oder Störungen verursachen.
22)Abhängig vom Standort, an dem das Gerät aufgestellt wird, kann in einem
nahe aufgestellten Radio ein Rauschen oder auf einem nahe aufgestellten
Fernseher ein Flimmern oder eine Verzerrung festgestellt werden. Wenn Sie
meinen, dass dieses Gerät solche Störungen hervorruft, schalten Sie den
Netzschalter dieses Geräts aus. Wenn dadurch das Radio und der Fernseher
wieder störungsfrei laufen, stellen Sie das Gerät mit einem größeren Abstand
zum Radio oder Fernsehgerät auf, oder ändern Sie die Ausrichtung des Radios
oder Fernsehgeräts.
DEUTSCH
37
Sicherheitshinweise
Lesen Sie diese Sicherheitshinweise sorgfältig durch, bevor Sie dieses Gerät
verwenden. Verwenden Sie es nur gemäß den Anweisungen.
Bewahren Sie diese Sicherheitshinweise nach dem Lesen zusammen mit der
Bedienungsanleitung“ und den Garantiehinweisen auf.
”
Vermeidung von Bränden, elektrischem Schlag und Verletzungen
Über die grafischen Symbole
DEUTSCH
zeigt eine Vorsichtsmaßnahme an (einschließlich Gefahren- oder
Warnhinweisen). Der besondere Inhalt der Warnung ist innerhalb
des Dreiecks angegeben. Die links gezeigte Grafik bezeichnet eine
allgemeine Vorsichtsmaßnahme, Warnung oder Gefahr.
zeigt ein Verbot an (etwas, das Sie nicht tun sollten). Der
besondere Inhalt des Verbots ist innerhalb des Symbols
illustriert. Die links gezeigte Grafik zeigt an, dass Sie das
Gerät nicht auseinander nehmen dürfen.
zeigt eine notwendige Maßnahme an (etwas, das Sie auf
jeden Fall tun sollten). Der besondere Inhalt der notwendigen
Maßnahme ist innerhalb des Symbols illustriert.
Warnungen
Wenn Rauch aus dem Gerät aufsteigt
Ein Brand oder Elektroschocks können auftreten, wenn Sie das Gerät bei
unüblichen Verhalten (aussteigender Rauch oder unüblicher Geruch)
weiterhin verwenden. Schalten Sie sofort den Netzschalter aus, ziehen
Sie das Netzkabel von der Steckdose ab, und benachrichtigen Sie den
Händler, bei dem Sie das Gerät erworben haben. Versuchen Sie nie, das
Gerät selbst zu reparieren; andernfalls können Schäden auftreten.
Wenn das Gerät zu Bruch geht
Wenn Sie das Gerät fallen lassen oder das Gehäuse beschädigt ist,
schalten Sie sofort den Netzschalter aus, ziehen Sie das Netzkabel von
der Steckdose ab, und wenden Sie sich an den Händler, bei dem Sie das
Gerät erworben haben. Ein Brand oder tödliche Elektroschocks können
auftreten, wenn Sie das Gerät unter solchen Bedingungen weiterhin
verwenden.
38
Wenn ein Fremdobjekt in das Gerät gelangt
Wenn ein metallenes oder entzündliches Fremdobjekt in das Innere dieses
Geräts durch eine Buchse oder andere Öffnung in das Gerät gelangt,
schalten Sie sofort den Netzschalter aus, ziehen Sie das Netzkabel von der
Steckdose ab, und wenden Sie sich an den Händler, bei dem Sie das Gerät
erworben haben. Ein Brand oder tödliche Elektroschocks können auftreten,
wenn Sie das Gerät unter solchen Bedingungen weiterhin verwenden.
Nehmen Sie das Gerät nicht auseinander, und
nehmen Sie keine Änderungen am Gerät vor
Öffnen Sie nicht das Gehäuse dieses Geräts. Dieses Gerät enthält
Komponenten unter Hochspannung. Das Berühren dieser Komponenten
kann zu elektrischen Schlägen führen. Wenden Sie sich an Ihren Händler,
wenn das Innere des Geräts geprüft oder gewartet werden muss.
Nehmen Sie keine Änderungen an diesem Gerät vor. Andernfalls kann
ein Brand, ein elektrischer Schlag oder Störungen auftreten.
Lassen Sie kein Wasser oder keine Chemikalien mit
dem Gerät in Berührung kommen
Um einen Brand oder elektrischen Schlag zu vermeiden, stellen Sie keine
Blumenvasen, Getränke, Kosmetika oder Behälter mit Chemikalien oder
Wasser auf dieses Gerät.
Trennen Sie das Gerät im Falle von Blitzschlag von
der Netzsteckdose
Wenn es in der näheren Umgebung blitzt, schalten Sie den Netzschalter
aus, ziehen das Netzkabel von der Steckdose und beenden die
Verwendung des Geräts. Blitze können einen Brand oder elektrischen
Schlag verursachen.
Setzen Sie das Gerät keinen Flammen oder keiner
Hitze aus
Dieses Gerät und das Netzkabel dürfen nicht in der Nähe von Heizungen
aufgestellt werden. Unter solchen Bedingungen kann das Gehäuse oder
die Ummantelung des Netzkabels schmelzen, was einen Brand oder
elektrischen Schlag verursachen kann.
Verwenden Sie das Gerät nicht für längere Zeit mit
hoher Lautstärke
Wenn Sie das Gerät für längere Zeit mit hoher Lautstärke über Kopfhörer
oder Lautsprecher verwenden, kann je nach Dauer und Lautstärke ein
dauerhafter Hörschaden entstehen.
Stellen Sie das Gerät nicht an Standorten mit hoher
Luftfeuchtigkeit auf
Verwenden Sie das Gerät nicht an Standorten mit hoher Luftfeuchtigkeit,
wie z. B. in der Nähe eines Bades oder Luftbefeuchters, im Regen oder in
der Nähe von Wasser. Dies kann sonst einen Brand oder einen elektrischen
Schlag zur Folge haben.
Blockieren Sie nicht die Kühlungsschlitze
Da sich auf der Rückseite des Geräts ein Lüftungsschlitz befindet, müssen
Sie genügend Platz zwischen dem Gerät und der Wand frei lassen. Wenn
der Kühlungsschlitz blockiert ist, kann die Hitze nicht aus dem Gerät
austreten, was möglicherweise einen Brand verursachen kann.
Stellen Sie das Gerät nicht an Standorten mit
hohen Temperaturen auf
Stellen Sie dieses Gerät nicht an Standorten mit hohen Temperaturen
auf, wie z. B. direktes Sonnenlicht oder in der Nähe von Geräten, die
Hitze erzeugen, wie z. B. ein Herd oder eine Heizung. Andernfalls kann
die innere Temperatur ansteigen und einen Brand verursachen.
Setzen Sie das Gerät keinen Ölspritzern oder
keinem Dampf aus
Setzen Sie dieses Gerät keinen Ölspritzern oder keinem Dampf aus. Dies
kann sonst einen Brand oder einen elektrischen Schlag zur Folge haben.
Verwenden Sie dieses Gerät nur mit einer
Steckdose, welche die richtige Spannung aufweist
Die für das Gerät richtige Spannung der Netzsteckdose wurde auf dem
Gerät vermerkt. Wenn Sie eine Netzsteckdose mit falscher Spannung
verwenden, kann dies zu einem Brand oder elektrischen Schlag führen.
Verwenden Sie das Gerät nicht mit nassen Händen
Wenn Ihre Hände nass sind, dürfen Sie das Netzkabel nicht anschließen
oder abziehen. Andernfalls können Sie einen elektrischen Schlag erleiden.
Handhaben Sie den Stecker mit Sorgfalt
Beim Abziehen des Kabels aus der Steckdose müssen Sie am Stecker
ziehen. Wenn Sie den Stecker abziehen, indem Sie am Kabel selbst
ziehen, kann das Kabel beschädigt werden und möglicherweise einen
Brand oder elektrischen Schlag verursachen.
Verwenden Sie keine verzweigten Anschlüsse
Verwenden Sie keine Verlängerungskabel mit mehreren Verzweigungen,
Steckdosenleisten oder Abzweigungen, um weit verzweigte Verbindungen
von einer Netzsteckdose zu erhalten. Dies kann sonst einen Brand oder
einen elektrischen Schlag zur Folge haben.
Handhaben Sie das Netzkabel mit Sorgfalt
Das Netzkabel darf nicht zerkratzt, beschädigt, verändert, übermäßig
verbogen, gezogen, verdreht oder gebündelt werden. Wenn schwere
Objekte auf das Netzkabel gestellt werden oder wenn das Netzkabel Hitze
ausgesetzt wird, kann es beschädigt werden und möglicherweise einen
Brand oder elektrischen Schlag verursachen. Wenden Sie sich an Ihren
Händler, falls das Netzkabel beschädigt wird.
Verwenden Sie dieses Gerät nur in dem Land, in
dem Sie es erworben haben
Dieses Gerät wurde für die Netzspannung des Landes konzipiert, in dem
Sie es erworben haben. Sie dürfen das Gerät nicht außerhalb dieses
Landes verwenden.
Vorsicht
Ziehen Sie das Netzkabel ab, wenn Sie nicht da
sind
Wenn Sie das Gerät über einen längeren Zeitraum nicht verwenden
werden, ziehen Sie aus Sicherheitsgründen das Netzkabel von der
Steckdose ab.
Lassen Sie das Gerät nicht fallen, oder setzen Sie
es keinen Stößen aus
Lassen Sie das Gerät nicht fallen, oder setzen Sie es keinen Stößen aus.
Andernfalls kann das Gerät zerbrechen, oder Störungen können auftreten.
Stellen Sie das Gerät nicht auf einer unebenen
Oberfläche auf
Stellen Sie dieses Gerät nicht auf einer unebenen Oberfläche auf, wie z.
B. ein wackliger Ständer oder in einem Winkel. Das Gerät ist dann
möglicherweise nicht mehr ausbalanciert und kann herunterfallen. Dies
kann zu Schäden oder Verletzungen führen.
DEUTSCH
39
Tutorial
Dieser Abschnitt führt Sie Schritt für Schritt durch die Bedienungsschritte,
vom Anschließen des Amps über das Einstellen, Speichern und
Zurücksetzen der Sounds bis hin zum Einsatz der Rhythmuspatterns.
Wenn Sie dieses Tutorial einmal durcharbeiten, sollten Sie fast alle
Funktionen des MIMX verstanden haben.
Die hier erscheinenden Abbildungen stammen vom Bedienfeld des MIMX
150H.
DEUTSCH
1. Anschlüsse
1)-a Lesen Sie aufmerksam die Hinweise zur Sicherheit, und bauen Sie
dann Ihren Amp auf. Verbinden Sie dann die Buchse 12 AC INPUT über
das beiliegende Netzkabel mit einer geeigneten Netzsteckdose.
Hinweis: Der Sound (besonders die Basswiedergabe) des Amps ändert
sich je nach den akustischen Bedingungen am Aufstellort des Amps.
1)-b Wenn Sie den MIMX 150H verwenden, schließen Sie den Ausgang
14
SPEAKER OUTPUT mit der 4-Ω-Eingangsbuchse Ihrer
Lautsprecherbox. Verwenden Sie für diese Verbindung ein
Lautsprecherkabel. An den Lautsprecherboxen der IS-Serie von Ibanez
sind zwei Eingangsbuchsen vorhanden.Verwenden Sie diejenige mit der
Aufschrift MONO 4Ω.
2) Schließen Sie Ihre E-Gitarre an der Buchse 1 INPUT an. Verwenden
Sie für diese Verbindung ein abgeschirmtes Kabel.
3) Wenn Sie einen Bodeneffekt benutzen, verwenden Sie ein
abgeschirmtes Kabel für die Verbindung zwischen Gitarre und Amp.
4) Achten Sie darauf, dass der Regler 10 MASTER auf 0 eingestellt ist,
und schalten Sie den Amp mit dem Schalter 11 POWER ein. Nach der
Animation während des Startvorgangs ist der Amp spielbereit.
Hinweis: Nach der Verwendung des Amps achten Sie darauf, dass der
Lautstärkeregler 10 MASTER auf 0 eingestellt ist, und schalten Sie den
Amp dann mit dem Schalter 11 POWER aus.
● Bei Einsatz des IFC2
Durch Anschluss des optionalen IFC2 (gesondert erhältlich) haben Sie
Zugriff auf die zusätzlichen fünf Pedaleffekte. Näheres zum Herstellen
der Verbindungen erfahren Sie in der Bedienungsanleitung des IFC2.
40
2. Einstellen Ihres Sounds
Lassen Sie uns nun einige Sounds erstellen. Für dieses Beispiel werden
wir das Programm 11 ”PSYCHO“ verwenden.
1) Klicken Sie im Speicherbereich 3 auf den Schalter MANUAL.
Dadurch wird der manuelle Modus ausgewählt, wobei alle SoundEinstellungen den tatsächlichen Reglerpositionen entsprechen.
2) Drehen Sie den Lautstärkeregler 10 MASTER auf eine Position zwischen 8 und 12 Uhr.
3) Stellen Sie den Vorverstärkerbereich 2 wie folgt ein.
Hinweis: Dieser Amp ist in der
Lage, extrem hohe Lautstärken
zu erzeugen. Bitte Stellen Sie
den Lautstärkeregler
TER so ein, dass Ihre
Nachbarschaft nicht gestört wird.
Dadurch erhalten Sie einen knackigen, verzerrten Sound. Wir werden
jetzt einige Effekte hinzufügen.
4) Zuerst werden wir den Effekt 7 MODULATION hinzufügen. Nehmen
Sie die folgenden Einstellungen vor.
FX TYPE&PARAMETER:FLANGER 15
* Lesen Sie den Abschnitt
Sinnvoller Einsatz der TAP-
”
Taste“ weiter hinten in
dieser Anleitung.
*Die obige Abbildung
zeigt den MIMX 150H.
FX MIX LEVEL :20
TAP TEMPO :10
5) Als Nächstes werden wir den Effekt 8 DELAY&REVERB hinzufügen.
Nehmen Sie die folgenden Einstellungen vor.
FX TYPE&PARAMETER:REVERB HL 10
Hinweis: Die TAP-Taste reagiert
auf leichteste Berührungen. Durch
Antippen mit übermäßiger Kraft
wird die Taste beschädigt, tippen
Sie sie also nur leicht an.
*Die obige Abbildung
zeigt den MIMX 150H.
FX MIX LEVEL :30
TAP TEMPO :1
Sie werden bemerken, dass der Sound räumlicher geworden ist. Fahren
Sie nun fort und erzeugen Sie Ihre eigenen Sounds auf die gleiche Weise.
Als Nächstes werden wir lernen, wie Sie einen eingestellten Sound
speichern können.
10
MAS-
3. Speichern eines selbst erstellten Sounds
In diesem Abschnitt erfahren Sie, wie Sie einen eingestellten Sound
speichern können. Wir werden Ihren neuen Sound in Bank A, Kanal 1
speichern.
* Näheres zur Initialisierung des Speichers erfahren Sie unter 5. Factory
Reset (Aufrufen der Werkseinstellungen)
1) Achten Sie darauf, dass das Display 5 M anzeigt. Halten Sie dann
die Taste ”1“ mindestens drei Sekunden lang fest. Wenn die Einstellungen
gespeichert wurden, zeigt das Display 5 A1 an und blinkt.
Hinweis: Jeder Kanal besitzt zwei Banken, A und B. Wenn Sie
Einstellungen in Bank A, Kanal 1 speichern möchten (wie in diesem
Tutorial nach manueller Einstellung des Sounds beschrieben), müssen
Sie zuerst
und dann nochmals die Taste MANUAL drücken, um in den manuellen
Modus zu schalten, bevor Sie die nachfolgenden Schritte ausführen.
1“ drücken, um sicherzustellen, dass Sie in Bank A sind,
”
4. Einsatz der Rhythmuspatterns
Dieser Abschnitt beschreibt die Verwendung der Rhythmuspatterns.
1) Wir beginnen mit der Wiedergabe eines Rhythmus. Drücken Sie die ON/
OFF-Taste. Die TAP-Taste blinkt, und Sie hören die Schlagzeug-Sounds.
Hinweis: Verwenden Sie den Regler RHYTHM, um die Lautstärke wie
gewünscht einzustellen.
2) Nun werden wir das Pattern umschalten. Drücken Sie + oder -, bis
das Display 5 16 anzeigt.
3) Wir werden jetzt das Tempo etwas schneller einstellen. Tippen Sie
mehrmals in gleichmäßigem Rhythmus auf die TAP-Taste, bis das Display 5 den Wert 120 anzeigt.
DEUTSCH
Ein Sound, den Sie wie hier beschrieben im manuellen Modus erstellt
Drei Sekunden oder länger gedrückt halten.
haben, kann auf jedem Kanal gespeichert werden. Ein Sound, den Sie
in einer der Banken erstellt haben, kann auf jedem Kanal innerhalb dieser
Bank gespeichert werden.
Hier folgt ein Beispiel.
2) Bis zu diesem Punkt haben wir immer Bank A, Kanal 1 verwendet,
um einen Sound zu erstellen/speichern, doch nun werden wir einige
Reglerpositionen leicht verändern und das Ergebnis in Bank A, Kanal 2
speichern. Führen Sie die folgenden Schritte aus.
Bearbeiten Sie den Sound
von Bank A, Kanal 1
Drei Sekunden oder länger
gedrückt halten
Der Sound wird auf
Bank A, Kanal 2
gespeichert
Nachdem Sie den geänderten Sound auf einem anderen Kanal
gespeichert haben, können Sie beide Sounds vergleichen. Nun wenden
wir uns dem Einsatz der Rhythmuspatterns zu.
Rhythmuspattern
abspielen
Rhythmuspattern
umschalten
Tempo des
Rhythmuspatterns ändern
Mit den oben beschriebenen Bedienungsschritten können Sie die
Rhythmuspatterns verwenden.
5. Factory Reset (Aufrufen der Werkseinstellungen)
Dieser Abschnitt beschreibt, wie Sie den Amp initialisieren können, um
den Auslieferungszustand ab Werk wiederherzustellen.
1) Halten Sie die Taste MANUAL gedrückt, wie in der Abbildung unten
gezeigt, und schalten Sie den Amp mit der Taste 11 POWER ein. Das
Display 5 zeigt AL an.
2) Wenn Sie in diesem Zustand die Taste MANUAL drücken, werden
alle Einstellungen auf die Werksvoreinstellung zurückgesetzt.
3) Wenn Sie sich entscheiden, die Funktion ohne Reset abzubrechen,
drücken Sie irgend eine andere Taste außer MANUAL. Hierdurch
verlassen Sie den Factory-Reset-Modus.
Schalten Sie den Amp bei
gehaltener MANUAL-Taste mit
dem Schalter POWER ein.
Im Display
erscheint AL.
5
Drücken Sie die
Taste MANUAL.
41
Bezeichnungen und Funktionen der Bedienungselemente
INPUT: Dies ist eine 6,3-mm-Klinkeneingangsbuchse.
1
Vorverstärkerbereich: Hier stellen Sie den Klang der Gitarre ein. Es folgen Beschreibungen
2
der einzelnen Bedienungselemente.
1) AMP SELECTION: (Amp-Auswahl) Mit diesem Drehschalter können Sie aus elf
Vorverstärkermodellen auswählen. Näheres erfahren Sie im Abschnitt über die einzelnen
Amps.
2) GAIN: (Verstärkung) Dieser Regler stellt die Verstärkung ein. Der Einstellbereich hängt
von der Einstellung bei AMP SELECTION ab. Je nach GAIN-Pegel zeigt das Display
DEUTSCH
einen Wert zwischen 0 und 100 an.
3) Klangregelung: Dies sind die Regler für die Pegel der drei Frequenzbänder des Equalizers (BASS, MIDDLE, TREBLE; Bass, Mitten, Höhen). Einstellbereich und Funktionsweise
hängen von der Einstellung bei AMP SELECTION ab. Je nach Einstellung zeigt das Display 5 einen Wert zwischen -15 und 15 an.
4) VOLUME: (Lautstärke) Mit diesem Regler wird der Ausgangspegel des Vorverstärkers
eingestellt. Je nach VOLUME-Pegel zeigt das Display 5 einen Wert zwischen 1 und 50
an. Der Ausgangspegel hängt vom ausgewählten Verstärkertyp, vom Gain-Pegel und den
Einstellungen der Klangregelung ab. Sie können diesen Regler verwenden, um
Pegelunterschiede zwischen den Kanälen auszugleichen bzw. den gewünschten Pegel
einzustellen. Die eigentliche Lautstärke wird mit dem Regler MASTER 10 eingestellt.
Speicherprogrammauswahl: Um einen von Ihnen erstellten Sound zu speichern, halten
3
Sie die Taste des gewünschten Zielkanals drei Sekunden oder länger gedrückt. Die
Einzelheiten sind im Folgenden beschrieben.
1) MANUAL: (Manuell) Diese Taste wählt den manuellen Modus aus, wobei alle SoundEinstellungen den tatsächlichen Reglerpositionen entsprechen. Das Display 5 zeigt M
an.
2) Kanäle (1-5): Diese Tasten wählen jeweils einen von fünf Kanälen aus, in dem Sie Ihre
eigenen Einstellungen speichern können. Es gibt zwei Banken (A und B), so dass Sie
insgesamt zehn Sounds speichern können. Alternativ zur Auswahl vom Bedienfeld können
Sie den optionalen Foot Controller IFC2 (gesondert erhältlich) anschließen und die Kanäle
mit dem Fuß umschalten. Das Display 5 zeigt die Kanalnummer an (1-5).
3) Bank-Schalter A/B: Es gibt zwei Banken, die jeweils fünf Kanäle enthalten.
Drum-Bereich: Sie können aus 50 verschiedenen Rhythmen auswählen.
4
*Die obige Abbildung
zeigt den MIMX 150H.
1) RHYTHM-Regler: Dieser Regler stellt die Lautstärke der
Rhythmusbegleitung ein.
2) ON/OFF: Diese Taste schaltet die Rhythmusbegleitung ein/aus.
3) -/+: Mit diesen Tasten können Sie aus den 50 verschiedenen
Rhythmen auswählen. Näheres zu den einzelnen Rhythmen erfahren
Sie im Abschnitt TECHNISCHE DATEN.
4) TAP-Taste: Diese Taste steuert das Tempo des Rhythmus in einem
Bereich von 40 BPM bis 199 BPM.
Display: Hier werden verschiedene Funktionen angezeigt.
5
TUNER ON/OFF: Der MIMX beinhaltet ein chromatisches Stimmgerät. Die folgenden
6
Abbildungen zeigen an, was im Display erscheint, wenn das Stimmgerät aktiv ist.
Leuchtet, um die korrekte
Stimmung anzuzeigen
Bewegung
im Display
5
Wenn die Tonhöhe zu
niedrig ist
MODULATION-Bereich: Hier können Sie vier Arten von Modulationseffekten einstellen.
7
1) FX-Regler: Dieser Regler wählt aus vier Modulationseffekten aus. Diese sind hier
aufgeführt.
*Die obige Abbildung
zeigt den MIMX 150H.
2) MIX-Regler: Dieser Regler steuert das Mischverhältnis des Modulationseffekts im
Bereich von 0 bis 100. In der Einstellung 0 ist der Effekt ausgeschaltet; es wird keine
Modulation angewendet.
3) TAP-Regler: Diese Taste steuert die Geschwindigkeit des Modulationseffekts im Bereich
von 1 bis 50. Die folgende Tabelle zeigt für jeden Modus die Modulationsgeschwindigkeit,
die mit der TAP-Taste eingestellt werden kann.
Näheres zur TAP-Taste erfahren Sie im Abschnitt "Über die TAP-Taste".
Hinweis: Wenn Sie im Bereich PEDAL FX 9 den Effekt PEDAL PITCH verwenden, können
Sie die Effekte des Bereichs MODULATION nicht einsetzen.
Wenn die Tonhöhe
richtig ist: Note E
a CHORUS: Dieser Effekt erzeugt einen vollen Klang, indem das Signal mit sich selbst überlagert und moduliert wird. Mit dem FX-Regler
können Sie die Modulationstiefe im Bereich von 0 bis 100 einstellen.
b FLANGER: Dieser Effekt wendet eine Modulation und einen
Phasenverlauf auf den Klang an. Mit dem FX-Regler können Sie die
Modulationstiefe im Bereich von 0 bis 100 einstellen.
c VIBRATO: Dieser Effekt wendet ein Vibrato auf den Klang an. Mit
dem FX-Regler können Sie die Modulationstiefe im Bereich von 0 bis
100 einstellen.
d STEP: Dieser Effekt variiert den Klang schrittweise. Mit dem FXRegler können Sie die Modulationstiefe im Bereich von 0 bis 100
einstellen.
Bereich DELAY & REVERB: Hier können Sie vier verschiedene
8
Delay&Reverb-Effekte einstellen.
1) FX-Regler: Dieser Regler wählt einen von vier Delay&Reverb-Effekten aus.
Diese Effekte sind folgend aufgeführt.
*Die obige Abbildung
zeigt den MIMX 150H.
2) MIX-Regler: Dieser Regler steuert das Mischverhältnis des Delay&ReverbEffekts im Bereich von 0 bis 100. In der Einstellung 0 ist der Effekt
ausgeschaltet, es ist kein Delay&Reverb-Effekt zu hören.
3) TAP-Taste: Wenn Sie DELAY oder ECHO verwenden, steuern Sie mit dieser
Taste die Verzögerungszeit. Wenn Sie REVERB verwenden, steuert diese
Taste die Halldauer. Die folgende Tabelle zeigt für jeden Modus die
Verzögerungs- oder Hallzeit, die mit der TAP-Taste eingestellt werden kann.
Anzeige im
Display
Näheres zur TAP-Taste erfahren Sie im Abschnitt ”Sinnvoller Einsatz der TAP-Taste“.
Hinweis: Sie können REVERB nicht benutzen, während Sie den Drum-Bereich
einsetzen 4.
Bereich PEDAL FX: Sie können Pedaleffekte mit einem optionalen Foot Con-
9
troller IFC2 (gesondert erhältlich) steuern. Näheres erfahren Sie unter
Zusatzinformationen über den Foot Controller“.
”
1) SELECT-Taste: Diese wählt einen aus fünf Pedaleffekttypen aus. Diese
Effekte sind folgend aufgeführt.
*Die obige Abbildung
zeigt den MIMX 150H.
a DELAY: Dieser Effekt fügt dem Klang eine verzögerte
Kopie des Originalsignals hinzu (kurzes Echo). Mit dem
FX-Regler können Sie das Feedback (Wiederholungsrate)
im Bereich von 0 bis 40 einstellen.
b ECHO: Dieser Effekt erzeugt eine längere Verzögerung
als der Delay-Effekt. Mit dem FX-Regler können Sie das
Feedback (Wiederholungsrate) im Bereich von 0 bis 40
einstellen.
c REVERB HL: Dieser Halleffekt simuliert die Akustik eines
großen Raumes wie z. B. einer Konzerthalle. Mit dem FX-
Regler können Sie den Klangcharakter des Halls im
Bereich von 0 bis 10 einstellen.
d REVERB RM: Dieser Raumklangeffekt simuliert die Akustik
eines kleinen Raumes. Mit dem FX-Regler können Sie den
Klangcharakter des Halls im Bereich von 0 bis 10 einstellen.
a VOL PEDAL: Dies ist ein Lautstärkepedal, mit dessen
Hilfe Sie die Lautstärke mit dem Fuß regeln können.
b RING MOD: (Ringmodulation) Dieser Effekt verleiht dem
Sound einen metallischen Charakter.
c AUTO RESO: (Auto-Resonanz) Dieser Effekt variiert die
Resonanzfrequenz je nach Ihrer Anschlagsstärke.
d WAH WAH: Dies ist ein Wah-wah-Effekt (Tiefpassfilter mit
einstellbarer Frequenz).
e PEDAL PITCH: Mit diesem Effekt können Sie die Tonhöhe
in Echtzeit variieren.
1~30
2) Drehregler: Dieser Regler steuert den Effekt des Bereichs PEDAL FX 9 .
Die Effekte in jedem Modus sind folgend aufgeführt.
Minimalstellun
3) Fußschalterbuchse: Hier können Sie bei Anschluss des gesondert
erhältlichen IFC2 die Fußschalter einsetzen.
4) Fußpedalbuchse: Hier können Sie bei Anschluss des optionalen IFC2
(gesondert erhältlich) den Bereich PEDAL FX
10
MASTER-Lautstärke: Dieser Regler regelt den an den Lautsprecher
gesendeten Pegel und bestimmt letztlich die Lautstärke.
11
POWER-Schalter: Dies ist der Netzschalter des Amps.
12
AC INPUT: Schließen Sie hier das beiliegende Netzkabel an.
13
LINE OUT (MIMX 150H): Dies ist eine Ausgangsbuchse für LineAusgangspegel.
14
SPEAKER OUT (MIMX 150H): Dies ist die Ausgangsbuchse für Lautsprecher.
Verwenden Sie ein Lautsprecherkabel zum Anschluss eines 4-Ω- oder 8-Ω-
Lautsprechersystems.
Hinweis: Wenn Sie ein Lautsprechersystem mit einer Impedanz von weniger
als 4 Ω anschließen, (z. B. eine Box mit 2 Ω), überhitzt sich der
Leistungsverstärker, so dass eine Schutzschaltung aktiv und die
Maximalstellun
9
einsetzen.
Signalausgabe unterbunden wird.
15
HEADPHONES (MIMX65): Dies ist eine Ausgangsbuchse für Kopfhörer.
16
CD INPUT (MIMX65): Dies ist eine Eingangsbuchse für Line-Eingangspegel.
Hier können Sie einen mobilen CD-Player oder MP3-Player anschließen.
DEUTSCH
43
AMP SELECTION
Mit dem Drehschalter AMP SELECTION (Verstärkerauswahl) können
Sie aus elf Vorverstärkermodellen auswählen. Aus den zahllosen
Gitarrenverstärkern, die es gibt, hat sich Ibanez auf die typischen Sounds
zehn klassischer Verstärker konzentriert, die von vielen Gitarristen
gespielt und geliebt werden. Der gesamte Signalweg von der
Eingangsbuchse bis zum Lautsprecher wurde analysiert und als
Vorverstärkermodell gespeichert. Der MIMX ist so beschaffen, dass sehr
einfach Sounds erzeugt werden können, die dem Klang dieser Amps
DEUTSCH
sehr ähnlich sind. Der EQ jeder Voreinstellung zieht den Gesamtklang
des betreffenden Amps in Betracht, einschließlich des Verhaltens bei
Einsatz der Regler „Presence“, „Bright“, „Resonance“ oder „Deep“, so
dass jedes Modell erstaunlich detaillierte Abbildungen der klassischen
Sounds erzeugt. Diese Sounds sind keinesfalls als exakte Replikationen,
sondern mehr als „Geschmacksrichtungen“ zu verstehen. Schließlich
ist noch ein dichter, weicher heavy Originalsound von Ibanez als Auswahl
Nummer 11 enthalten. Er trägt passenderweise den Namen „Psycho“.
BITTE BEACHTEN: In den folgenden Beschreibungen der Vorverstärker
werden Bezeichnungen von Produkten verwendet, die nicht von Ibanez
stammen, um Ihnen anschaulich zu vermitteln, um welche Art von
Klängen es sich handelt und um die Verstärkerklänge zu benennen, die
als Grundlage der MIMX-Einstellungen gedient haben. Diese Bezüge
und Vergleiche mit nicht von Ibanez stammenden Produkten sind
vollständig subjektiv. Ibanez behauptet unter keinen Umständen, dass
die MIMX-Vorverstärkermodelle exakte Repliken der Amps sind, auf die
sie sich beziehen oder mit denen sie verglichen werden. Dies
vorausgeschickt glauben wir, dass Sie aufgrund der großen Vielfalt der
erzielbaren Klänge die Sounds Ihres neuen MIMX lieben werden.
44
60s Clean:
Dieses Preset wurde erschaffen, um den Sound eines der klassischen
Amps von Fender® nachzuahmen, des ’65 Twin Reverb®, gespielt auf
dem NORMAL-Kanal und mit ausgeschaltetem BRIGHT-Schalter. Wenn
man an die Clean-Sounds der Sechzigerjahre denkt, ist diese Vorstellung
direkt mit diesem Amp verbunden. Der Sound dieses Vorverstärkers
betont die glitzernden Höhen und die soliden Bässe, die an die
klassischen 60er-Sounds erinnern, hat aber trotzdem einen
unverwechselbar eigenen Klang.
Jazz Combo:
Diese Auswahl wurde durch den Sound des Roland® JC-120 inspiriert,
berühmt für seine Fähigkeit, den direkten Klang der Gitarre selbst zu
vermitteln. Er wird gespielt über Kanal 1, mit ausgeschaltetem BRIGHTSchalter und insgesamt weicher Klangeinstellung. Der große, unverfärbte
Klangbereich dieses Vorverstärkers von den Bässen bis in die Höhen ist
ein guter Basis-Sound für die weitere Bearbeitung mit Effektgeräten,
was dieses Modell sehr vielseitig macht.
70s Brit:
Dieser Vorverstärker liefert einen Sound, den wir als Reminiszenz an
den Marshall® „JCM800 2203“ verstehen, in Kombination mit dem Overdrive, der mit dem Ibanez® TUBESCREAMER®/TS-9 als BoosterVorstufe erzeugt wird. Von soliden Akkorden bis hin zu glänzenden Soli
deckt dieser Preamp einen großen Bereich kreativer Sounds ab.
Brit Blues:
Die Geschichte des VOX® „AC30“ verläuft entlang eines breiten Stroms
der Musikgeschichte des Blues, Rock und Pop. Sein Ruhm ist bis heute
ungebrochen, und er wird immer noch von zahlreichen Musikern geliebt,
daher fanden wir, dass ein Vorverstärker mit dieser Art von Sound
selbstverständlich dabei sein muss. Bei der Erstellung des Sounds im
MIMX haben wir mehr Gain hinzugefügt, mit einem besonders klaren
Mittenbereich und hoher Dichte, um den klassischen Klang noch etwas
zu betonen. Die Nuancen beim Picking werden getreu übertragen, so
dass Sie mit einer Vielzahl von Sounds spielen können.
US Blues:
Diese Auswahl ist unserer Auffassung nach der Sound eines Fender®
„Hot Rod Deville™“, gespielt über den DRIVE-Kanal, mit BRIGHT auf
NORMAL und mit eingeschaltetem MORE DRIVE. Im MIMX sind die
Bässe dieses Sounds etwas dichter und der EQ ist auf Niveauregelung
eingestellt. Die besondere Anziehungskraft dieser Auswahl ist der helle
Sound mit einer deutlichen, harten Resonanz. Von einem Sound mit
wenig Gain, der den harten Klangcharakter betont, bis hin zum
großartigen Drive bei maximalem Gain, liefert dieser Preamp eine breite
Klangpalette.
Rock:
Mit dieser Wahl landen Sie beim „Ecstasy 101B EL34 Version“, einem
Multifunktions-Röhrenamp von der Bogner Corporation, berühmt für ihre
Boutique-Amps. Die verschiedenen Einstellungen bieten einen
verbesserten Dynamikumfang von wenig bis viel Verzerrung und großem
EQ-Regelbereich. Mit Fokus auf den kantigen Sound gibt es mit dieser
Einstellung doch eine große Vielfalt von süßlichen und Clean-Sounds
bis hin zu harten Akkordklängen oder Overdrive-Sounds mit viel Sustain.
Hard Rock:
Zuerst nur für Wenige auf Kundenwunsch gebaut, erreichte der „SL0-
100“ von Soldano® später großen Erfolg und war weltweit bekannt. Wir
haben diese Einstellung so erzeugt, dass sie dem Sound des OVERDRIVE-Kanals des SLO-100 ähnelt, wobei der BRIGHT-Schalter auf
NORMAL steht, jedoch mit verringerter Rückkopplungsgefahr und einer
hohen Spannung und Dichte. Wir finden den Sound besonders in den
Höhen sehr gut, er ist eine ideale Wahl für Lead-Gitarre oder heavy
Riffs.
Guitar God:
Hier hören Sie unsere Vorstellung vom Klang eines Peavey® „5150 II®“.
Bei der Erstellung dieses MIMX-Preamps haben wir sowohl den
wirklichen Peavey-Amp gehört als auch Hörproben von einer CD, um
die Sounds zu reproduzieren, die nach unserem Eindruck den Aufnahmen
am Nächsten kommen. Die dichten Bässe sind sehr gut für Riffs mit
abgedämpften Saiten geeignet, und die Verzerrung und das Sustain
werden Ihre Soli deutlich hörbar machen.
90s Brit:
Dieser Preamp wurde ebenfalls erstellt, indem wir sowohl den Amp gehört
haben, in diesem Fall den Marshall® „JCM2000 DSL100“, und CDAufnahmen einer Band, die diesen Amp verwendet hat. Unsere Interpretation des Sounds hat eine raue Verzerrungskomponente; der Sound
ist jedoch dicht und klar definiert, mit guter Unterscheidung der Noten,
so dass alles möglich ist von glitzernden Arpeggios bis zu flashigen Riffs.
Ihr Gitarrensound sticht in jedem Fall hervor, auch in einer lauten Band.
LA Heavy:
Der Mesa/Boogie® „Dual Rectifier® Solo Head“ hat zahlreiche Musiker
mit heavy Styles beeinflusst. Dieser Preamp ist unsere Interpretation
einer Collage klassischer Sounds eines Modells von 1989, das einen
definierten, modernen Heavy-Gitarrensound liefert. Unsere Version bietet
den verzerrten Sound der originalen 6L6-Endstufenröhren über den RED-
Kanal und bei Stromversorgung im BOLD-Modus, mit Einsatz der
Silizium-Gleichrichterdiode und schließlich gespielt über ein Ibanez®
Thermion® TN412A-Box mit vier 12-Zoll-Lautsprechern. Das Ergebnis
sind monströse Bässe mit starkem Crunch-Sound.
Psycho:
Dies ist ein eigener Sound von Ibanez, speziell erstellt um den Mainstream der heutigen Heavyrockszene einzufangen. Er bietet dichte,
deutliche Bässe und eine außergewöhnliche Klarheit. Durch
Ver änderungen der EQ-Einstellungen können Sie diesen Sound mit
praktisch allen Musikrichtungen einsetzen.
* Mit Ausnahme der Bezeichnungen Ibanez®, TUBESCREAMER®
und Thermion® sind die in dieser Anleitung erscheinenden
Firmennamen und Produktbezeichnungen Warenzeichen oder
eingetragene Warenzeichen der jeweiligen Eigentümer und stehen
nicht im Zusammenhang mit Ibanez.
Fender®, Twin Reverb®, Hot Rod Deville™ sind eingetragene
Warenzeichen oder Warenzeichen der Fender Musical Instruments
Corporation.
Roland® ist ein eingetragenes Warenzeichen der Roland Corporation.
Marshall® ist ein eingetragenes Warenzeichen der Marshall Amplification PLC.
VOX® ist ein eingetragenes Warenzeichen der VOX R&D Ltd.
Soldano® ist ein eingetragenes Warenzeichen von Soldano Custom
Amplification.
Peavey® ist ein eingetragenes Warenzeichen der Peavey Electronics
Ltd.
5150 II® ist ein eingetragenes Warenzeichen der E.L.V.H., Inc.
Mesa/Boogie® und Dual Rectifier® sind eingetragene Warenzeichen
von Mesa/Boogie, Ltd.
DEUTSCH
45
Werks-Presets
Dies sind die Sound-Einstellungen, die den Kanälen A1-B5 zugewiesen
sind, wenn der MIMX das Werk verlässt. Mit einem einzigen Tastendruck
können Sie die charakteristischen Kombinationen von Sounds und
Effekten des MIMX abrufen.
A1: Immortal Shred
AMP SELECTION: Psycho
Dieses Preset ist ideal für die typischen, schnellen Riffs aktueller SlashMetal- oder Death-Metal-Bands. Die Mitten sind abgesenkt, um die Höhen
DEUTSCH
und die Bässe zu betonen, und es wird durch Bassanhebung und ohne
zu starke Mittenabsenkung ein schwerer und robuster Sound erzeugt.
A2: Shrapnel Heroes
AMP SELECTION: Psycho
Dieses Preset kann für Gitarrensoli in einer großen stilistischen
Bandbreite von Hardrock bis Heavy Metal verwendet werden. Die EQEinstellung ist relativ neutral. Wenn Sie ein relativ kurzes Delay
hinzufügen, erhalten Sie mit diesem Preset einen interessanten SoloSound.
A3: Cruel Heaviness
AMP SELECTION: 90s Brit
Dieses Preset ist gut für rhythmusbetonte Riffs geeignet. Es ist ideal für
langsame Songs, und der angehobene Bassbereich verleiht Ihnen einen
verzerrten Heavy-Sound, der den gesamten Sound Ihrer Band
zusammenhält. Dieses Preset ist ideal für laute Rock-Sounds der
modernen Musikszene.
A4: Legend of the Beast
AMP STYLE: Hard Rock
Dies ist ein Preset für den klassischen Metal-Sologitarren-Sound der
80er. Dieses Preset besitzt einen Klangcharakter, der an das Golden
Age des Metal erinnert, wie es von zahlreichen britischen und LA-MetalBands verkörpert wird.
A5: Emotional Clean
AMP STYLE: 60s Clean
Dieses Clean-Preset gibt Ihnen voluminöse Bässe, einen spröden Attack und Hall und schafft eine warme Atmosphäre. Mit einem SingleCoil-Pickup können Sie einen brillanten Vintage-Sound erzeugen. Indem
Sie das Mischverhältnis des Reverb-Effekts verringern, können Sie die
Empfindsamkeit des Attacks betonen.
46
B1: Sounds of the Right Hand
AMP SELECTION: Guitar God
Dieses Preset ist ideal sowohl für heavy und knackige Riffs als auch für
Lead-Gitarre. Die Verzerrung, die durch maximale Anhebung des GAIN
und druckvolle Mitten-Einstellung entsteht, bietet eine gute Unterstützung
für Humbucker-Pickups. Für etwas Drive wurde ein leichter Flanger
hinzugefügt, und ein Delay sorgt für den Raumeffekt.
B2: Purple Tone
AMP SELECTION: Rock
Dies ist eine Einstellung mit viel Gain und stark abgesenkten Bässen,
wodurch sich ein charakteristisch starker Sound in den Mitten ergibt.
Durch Verwendung von Single-Coil-Pickups können Sie den Sound Mitte
der 70er nachbilden. Je weiter Sie den MIDDLE-Regler aufdrehen, desto
mehr gewinnt der Sound klassische Atmosphäre - stellen Sie diesen je
nach Geschmack ein. Um diesen Sound vorteilhaft einzusetzen, spielen
Sie die Hardrock-Riffs, die zu dieser Zeit revolutionär waren und heute
den Ursprung des Heavy Rock darstellen.
B3: Crystal Clean
AMP SELECTION: Jazz Combo
Dieses Preset wurde geschaffen, um einen glitzernden und kristallklaren
Clean-Sound zu erzeugen. Er passt am Besten zu den Hardrock- und
Heavy-Metal-”Power-Balladen“ der 80er und 90er. Spielen Sie diesen
mit Single-Coil-Pickups, entweder mit dem mittleren Pickup oder einer
Kombination aus mittlerem und Hals-Pickup. Erhöhen Sie den Effektanteil,
um einen volleren Sound zu erhalten.
B4: Solo DNA
AMP SELECTION: Rock
Dieses Preset wurde für Sie erschaffen, um die übermächtigen
Gitarrensoli der Gitarrengötter der 80er zu spielen! Diese Einstellung ist
geeignet, um Ihrer Musikalität freien Lauf zu lassen. Ziehen Sie die Saiten,
spielen Sie Abstürzer, gleitende Arpeggios, zupfen Sie Obertöne - alles
was Ihrer Vorstellung entspringt.
B5: Samurai Edge
AMP SELECTION: 70s Brit
Dieses Preset ist eine gute Wahl für Comping oder bluesige Riffs, die
mit einem Single-Coil-Pickup gespielt werden. Es hat genau den richtigen
Anteil an Verzerrung, um die Nuancen Ihrer Zupftechnik zu betonen und
bietet schöne klare Höhen. Stellen Sie den Hallanteil nach Ihrem
Geschmack ein.
Sinnvoller Einsatz der TAP-Taste
Der MIMX bietet eine TAP-Taste, mit der Sie das Tempo von Effekten
und Rhythmen einstellen können. Die Funktionsweise mag Ihnen etwas
ungewohnt erscheinen, aber Sie werden die Funktion schnell erlernen
und intuitiv benutzen können.
Durch mehrfaches Antippen (”Tapping“) dieser Taste (mehr als zwei Mal)
können Sie das gewünschte Tempo angeben. Während Sie weiter tippen,
erscheint der durchschnittliche Abstand im Display 5.
Für diejenigen, die eine ”technische“ Erklärung wünschen, folgt hier eine
genaue Beschreibung, wie die TAP-Funktion das durchschnittliche Tempo
erkennt.
Ein veränderlicher Durchschnittswert
Die Tempo- oder Geschwindigkeitserkennung mittels der TAP-Taste wird
mit einer Methode namens ”veränderlicher Durchschnitt“ vorgenommen.
Wenn Sie z. B. das Schlagzeugtempo auf 120 BPM einstellen möchten,
ist es recht schwierig, das Tempo durch nur zweimaliges Antippen der
TAP-Taste zu treffen.
Ver änderlicher Durchschnitt mit vier Werten (wir verwenden hier zur Erklärung vier
Werte)
Der Durchschnittswert der vier letzten Betätigungen der TAP-Taste wird als
Tempowert genommen. Dadurch werden Ungenauigkeiten Ihrer
ausgeglichen.
Eingegebener
1125bpm2115bpm3130bpm4109bpm
Wert
Ausgegebener
Wert
1
125bpm120bpm121bpm119bpm123bpm
(1+2)
2
Ver änderlicher Durchschnitt mit zwei Werten
Sie müssen die TAP-Taste genau im Rhythmus antippen, so
dass der Abstand zwischen dem ersten und zweiten Antippen
60/120 Sekunden = 0,5 Sekunden beträgt.
(1+2+3)3(1+2+3+4)4(2+3+4+5)
Der MIMX verwendet einen veränderlichen Durchschnitt aus bis zu sieben
Werten. Indem Sie die Schläge mit der TAP-Taste markieren, können
Sie eine sehr genaue Tempoeinstellung erreichen.
”
5131bpm
4
Taps“
Über die Bearbeitungsanzeige im mittleren Display
Der MIMX hat eine LED, die eine Bearbeitung anzeigt, und die wie in
folgender Abbildung dargestellt leuchtet.
Bearbeitungs-LED
Reglerposition
Position für den
aktuellen Sound
Wertes bewegen, leuchtet die Bearbeitungs-LED unten rechts im Display 5, um den Bearbeitungszustand anzuzeigen. Wenn Sie den Regler
auf die Position bewegen, die dem gespeicherten Wert entspricht, erlischt
die Bearbeitungs-LED. Dies ist der Wert, der im ausgewählten Kanal
gespeichert ist.
Hier folgt ein Beispiel.
1) Klicken Sie auf A1.
2) Stellen Sie den GAIN-Regler auf 12-Uhr-Position. Das Display 5 zeigt 50 an, und der Punkt
leuchtet. Dies zeigt an, dass Gain verändert wurde,
und dass dessen Einstellung vom gespeicherten
Gain-Wert abweicht.
3) Stellen Sie den GAIN-Regler auf Maximum. Das
Display 5 zeigt 100 an, und der Punkt erlischt.
Dies zeigt an, dass der gespeicherte Gain-Wert
im Display 5 zu sehen ist.
* Diese Funktionsweise gilt für alle Regler. Sie können sie verwenden,
um den gespeicherten Wert mit dem aktuellen zu vergleichen, oder um
zu überprüfen, welche Werte in den einzelnen Kanälen gespeichert sind.
* Wenn Sie mit der Taste MANUAL den manuellen Modus auswählen,
entsprechen die Stellungen aller Regler dem tatsächlichen Wert, der
den momentanen Sound bestimmt.
Der MIMX bietet analoge-Drehregler
für praktische Bedienung. Wenn Sie
jedoch auf einen Kanalschalter A1-B5
klicken, um die gespeicherten
Einstellungen abzurufen, entsprechen
die Klangeinstellungen an den Reglern
des vorderen Bedienfeldes nicht
immer den wirklichen Einstellungen
der Regler. Wenn Sie also auf einen
Kanalschalter klicken, um ein
Speicherprogramm abzurufen, und
dann einen Regler auf eine andere
Position als die des gespeicherten
47
DEUTSCH
Zusatzinformationen über den Foot Controller
Sie können den Foot Controller IFC2 (gesondert erhältlich) als Controller für den MIMX verwenden. Wenn Sie den IFC2 anschließen, können
Sie den Bereich 9 PEDAL FX benutzen, und mit den Fußschaltern
können Sie die Kanäle umschalten.
DEUTSCH
a
e
d
b
f
c
A
B
Funktionen
a
Pedal: Steuert den Pedaleffekt, der am Amp ausgewählt wurde.
Up-Schalter: Schaltet vom momentan ausgewählten
b
Speicherprogramm auf das nächsthöhere um. (Funktioniert nicht
im manuellen Betriebsmodus.)
c
Down-Schalter: Schaltet vom momentan ausgewählten
Speicherprogramm auf das nächstniedrigere um. (Funktioniert nicht
im manuellen Betriebsmodus.)
Drücken Sie b c gleichzeitig, um das Stimmgerät (Tuner)
zu aktivieren.
d
Fußschalterbuchse: Verbinden Sie diese mit dem Amp, um die
Fußschalter benutzen zu können.
e
Pedaleffektbuchse: Verbinden Sie diese mit dem Amp, um den
Pedaleffekt benutzen zu können. Eine Schaltung im IFC2 ermöglicht
dem MIMX zu erkennen, ob das Pedal angeschlossen ist.
Modusschalter: Dieser Schalter legt fest, wie das Pedal funktioniert.
f
Stellen Sie diesen Schalter je nach Ihren Spielgewohnheiten ein.
A
Der Effekt bleibt auch dann eingeschaltet, wenn das Pedal in
Minimalstellung steht (ganz oben).
B
Der Effekt schaltet sich aus, wenn das Pedal in Minimalstellung
steht (ganz oben).
48
Fehlersuche
Prüfen Sie zunächst, ob das abgeschirmte Gitarrenkabel, das Lautsprecherkabel
sowie das Netzkabel richtig angeschlossen sind. Falls möglich verwenden Sie
einen Kabeltester zum Prüfen der Kabel, oder probieren Sie andere Kabel oder
einen anderen Verstärker aus, um den Zustand Ihrer Kabel festzustellen.
1. Die Netzversorgung läßt sich nicht einschalten.
• Prüfen, ob das Netzkabel korrekt angeschlossen ist.
• Den Netzstecker an eine andere Steckdose anschließen, um zu prüfen, ob hier
das gleiche Problem auftritt.
2. Die Netzversorgung ist eingeschaltet, aber es wird kein
Klang erzeugt.
• Prüfen, ob die Gitarre korrekt angeschlossen ist.
• Die eingeschleiften Effektgeräte bzw. die Effekte zwischen dem Instrument und
dem Verstärker entfernen und prüfen, ob Sie dann etwas hören.
• Ein anderes geschirmtes Kabel verwenden und prüfen, ob Sie dann etwas hören.
• Nachschauen, ob der Lautstärkeregler der Gitarre auf ”0“ gestellt ist.
• Versuchsweise eine andere Gitarre verwenden und prüfen, ob damit Klang
erzeugt wird.
• Prüfen, ob der Lautstärkeregler des Verstärkers auf ”0“ gestellt ist.
• Nachschauen, ob ein Kopfhörer angeschlossen ist.
• Hören Sie immer noch keinen Ton, wenn Sie die Gesamtlautstärke erhöhen?
• Prüfen Sie, ob Sie den gesondert erhältlichen Foot Controller IFC2 als
Volumenpedal verwenden, und ob das Pedal evtl. ganz zugeregelt ist (ganz
oben).
3. Es treten Rauschstörungen auf.
• Prüfen, ob ein Gegenstand in der näheren Umgebung Resonanz erzeugt oder
gegen den Verstärker schlägt.
• Prüfen, ob der Plastikmantel des Instrumentenkabels locker ist.
• Stellen Sie sicher, dass die Saitenlage (Saitenhöhe) Ihrer Gitarre richtig
eingestellt ist.
• Gitarre, Effektgerät, andere Geräte und Kabel versuchsweise austauschen und
prüfen, ob die Rauschstörungen danach verschwinden.
4.Kein Ton beim Anschluss an einen CD-Player.
•
Stellen Sie sicher, dass die Lautstärke des CD-Players nicht auf 0 geschaltet ist.
• Stellen Sie sicher, dass das Kabel richtig angeschlossen ist.
• Probieren Sie ein anderes Kabel aus und prüfen Sie, ob etwas zu hören ist.
5. Die CD-Wiedergabe klingt nicht gut.
Hat das von Ihnen verwendete Kabel einen Stereostecker? Verwenden Sie
eventuell einen monauralen Stecker?
6. Bei Kopfhöreranschluss wird kein Klang erzeugt.
• Prüfen, ob der Kopfhörer korrekt angeschlossen ist.
• Versuchsweise einen anderen Kopfhörer anschließen und prüfen, ob Sie etwas
hören.
7. Es ist kein Schlagzeug zu hören.
• Prüfen Sie, ob evtl. die Drum-Lautstärke auf 0 eingestellt ist.
• Prüfen Sie, ob evtl. die Gesamtlautstärke auf 0 eingestellt ist.
• Prüfen Sie, ob evtl. Kopfhörer angeschlossen sind.
8. Es ist kein Modulationseffekt zu hören.
• Prüfen Sie, ob evtl. der Mix-Pegel auf 0 eingestellt ist.
• Prüfen Sie, ob Sie evtl. das im MIMX eingebaute Stimmgerät verwenden.
• Prüfen Sie, ob Sie evtl. den gesondert erhältlichen Foot Controller IFC2 für die
Steuerung von PEDAL PITCH verwenden.
9. Es ist kein Delay-Effekt zu hören.
• Prüfen Sie, ob evtl. der Mix-Pegel auf 0 eingestellt ist.
•Ändert sich etwas, wenn Sie die Tap-Funktion bedienen?
• Prüfen Sie, ob Sie evtl. das im MIMX eingebaute Stimmgerät verwenden.
10. Es ist kein Halleffekt zu hören.
• Prüfen Sie, ob evtl. der Mix-Pegel auf 0 eingestellt ist.
• Prüfen Sie, ob sich etwas ändert, wenn Sie die Tap-Funktion bedienen.
• Prüfen Sie, ob Sie evtl. die Drum-Funktion verwenden.
• Prüfen Sie, ob Sie evtl. das im MIMX eingebaute Stimmgerät verwenden.
11. Der Pedaleffekt lässt sich nicht verwenden.
• Ist der gesondert erhältliche Foot Controller IFC2 angeschlossen?
• Verwenden Sie das mit dem IFC2 gelieferte Kabel?
• Prüfen Sie, ob Sie evtl. das im MIMX eingebaute Stimmgerät verwenden.
Im Falle von Defekten
Der Verstärker wurde im Rahmen der Qualitätskontrolle vor dem Versand
gründlich überprüft. Bei eventuellen Problemen den Verstärker deshalb zuerst
mit Hilfe der obigen Punkte überprüfen. Sollten während des Betriebs Störungen
auftreten, wenden Sie sich bitte an Ihren Fachhändler. Erklären Sie das Problem bei notwendigen Reparaturen bitte möglichst genau, damit sich die Ursache
so schnell wie möglich finden läßt.
Änderungen der technischen Daten im Hinblick auf Produktverbesserungen ohne
Vorankündigung jederzeit vorbehalten.
49
DEUTSCH
Avant-propos
Nous vous remercions d'avoir porté votre choix sur l'amplificateur pour guitare
Ibanez de la série MIMX. Le MIMX est un amplificateur à modélisation produisant
des sons haute qualité grâce à un traitement de signaux 32 bits. Lisez
attentivement ce manuel avant d'utiliser l'amplificateur afin de profiter au maximum des fonctions disponibles. Conservez ce manuel dans un endroit sûr.
Précautions durant l'utilisation
1) Lisez les précautions du présent mode d'emploi.
2) Conservez-les afin de pouvoir vous y référer ultérieurement.
FRANÇAIS
3) Respectez scrupuleusement toutes ces précautions.
4) Respectez les instructions du présent mode d'emploi.
5) Utilisez uniquement un chiffon sec pour nettoyer votre amplificateur.
6) Ce produit peut générer des volumes sonores extrêmement élevés. Ceci peut,
dans certains cas, provoquer des dommages auditifs ou autres. Faites attention
au niveau de volume sonore lorsque vous utilisez ce produit.
7) Veillez toujours à ce que l'impédance des haut-parleurs connectés soit correcte.
8) Veillez à utiliser la tension d'alimentation appropriée, telle qu'imprimée sur le
panneau arrière.
9) Veillez à ce que le câble d'alimentation ne soit pas pincé, ou qu'il ne soit pas
nécessaire de l'enjamber, en particulier à proximité de la prise de courant.
10)Placez ce produit près d'une prise de courant principale et veillez à ce que la
fiche puisse être facilement déconnectée de la prise en cas de problème.
11)Utilisez uniquement les éléments inclus ou les pièces en option se conformant
aux spécifications du fabricant.
12)Cet appareil est protégé par un fusible. Le fusible peut ne plus fonctionner en
raison d'un choc physique externe ou parce qu'il a atteint la fin de sa durée de
vie. Toutefois, étant donné qu'un fusible endommagé peut indiquer un
dysfonctionnement interne grave, contactez votre revendeur avant de le
remplacer.
13)Confiez toutes les réparations à un personnel qualifié agréé par le distributeur.
Un contrôle ou un entretien sera nécessaire si le câble d'alimentation ou la fiche
est endommagée, si un liquide s'échappe de l'unité, si un corps étranger a
pénétré à l'intérieur, si l'amplificateur est exposé à l'eau, s'il tombe
accidentellement ou s'il ne fonctionne pas normalement.
14)Toujours éteindre l'interrupteur lorsque l'appareil ne doit pas être utilisé. Tant
que le MIMX est raccordé à une prise électrique, il n'est pas complètement
isolé de l'alimentation secteur même si son interrupteur principal est éteint. Si
l'appareil ne doit pas être utilisé pendant une longue période, débrancher le
câble d'alimentation.
15)Ne mettez pas l'appareil hors tension ou ne déconnectez pas la fiche de la
prise secteur lorsque l'appareil fonctionne. Des dysfonctionnements risqueraient
de se produire.
16)Ne montez pas dessus et n'y placez pas d'objets lourds. Vous risqueriez de le
casser ou d'entraîner un dysfonctionnement.
50
Précautions concernant l'emplacement
17)Si vous comptez utilisez le MIMX après l'avoir placé sur une enceinte, vous
devez attacher solidement cette dernière au plancher ou à un mur. En particulier
si vous utilisez deux enceintes (c.-à-d., empilées l'une sur l'autre), assurezvous que votre équipement est posé sur une surface plane et utilisez des
courroies de sécurité ou autres attaches pour fixer l'équipement au plancher ou
aux murs afin qu'ils ne puisse pas basculer.
18)Ne placez pas l'appareil dans un endroit soumis à une température
particulièrement basse, comme dans une chambre réfrigérée. L'appareil risque
de ne plus fonctionner correctement.
19)Ne placez pas l'appareil dans un endroit soumis à des champs magnétiques
puissants, comme près d'un poste de télévision ou de radio, ou de tout autre
appareil émettant une radiation électromagnétique. Cet appareil risque de ne
plus fonctionner correctement dans de telles conditions.
20)Ne placez pas l'appareil dans un endroit soumis à des variations de température
Si cet appareil se trouve dans un endroit frais dont la température augmente
soudainement, de la condensation risque de se former à l'intérieur de l'appareil,
qui pourrait ne plus fonctionner correctement.
21)Ne placez pas l'appareil dans un endroit poussiéreux ou soumis à des vibrations excessives
Ceci risquerait d'endommager l'appareil ou d'entraîner des dysfonctionnements.
22)En fonction de l'emplacement de cet appareil, du bruit risque de se produire
dans un poste de radio se trouvant à proximité, ou un scintillement ou une
distorsion à l'écran d'un poste de télévision proche sont possibles. Si vous pensez
que cet appareil en est responsable, mettez-le hors tension. Si le poste de radio
ou de télévision fonctionne de nouveau normalement, essayez d'en éloigner
l'appareil ou de changer l'orientation du poste.
FRANÇAIS
51
Consignes de sécurité
Lisez attentivement ces consignes de sécurité avant d'utiliser cet appareil, en
veillant à ce que son utilisation y soit conforme.
Une fois que vous les avez lues, conservez-les avec le "Manuel de l'utilisateur"
et la "Garantie".
Prévention des risques d’incendie, d’électrocution ou de blessure
A propos des symboles graphiques
FRANÇAIS
signale une mise en garde (danger ou avertissement). Le
contenu spécifique de cette mise en garde est indiqué dans
le triangle. Le symbole de gauche fait référence à une mise
en garde, un avertissement ou un danger d'ordre général.
signale une interdiction (action à ne pas réaliser). Le
contenu spécifique de cette interdiction est indiqué dans le
symbole. Le symbole de gauche signifie que vous ne devez
pas démonter l'unité.
signale une action obligatoire (action indispensable).
L'action spécifique est décrite dans le symbole.
Avertissements
Si l'appareil émet de la fumée
Un incendie ou une électrocution sont possibles si vous continuez à utiliser l'appareil s'il ne fonctionne pas normalement, par exemple, s'il émet
de la fumée ou s'il dégage une odeur inhabituelle. Mettez immédiatement
l'appareil hors tension, déconnectez la fiche de la prise secteur et contactez le revendeur auprès duquel vous l'avez acheté. N'essayez jamais
de réparer vous-même l'appareil ; cela peut s'avérer dangereux.
Si l'appareil est endommagé
Si vous laissez tomber l'appareil ou si son boîtier est endommagé, mettez-le immédiatement hors tension, déconnectez la fiche de la prise secteur et contactez le revendeur auprès duquel vous l'avez acheté. Un incendie ou une électrocution sont possibles si vous continuez à utiliser
l'appareil dans ces conditions.
52
Si un corps étranger pénètre dans l'appareil
Si un corps étranger métallique ou inflammable pénètre dans l'appareil
par une prise ou une autre ouverture, mettez-le immédiatement hors tension, déconnectez la fiche de la prise secteur et contactez le revendeur
auprès duquel vous l'avez acheté. Un incendie ou une électrocution sont
possibles si vous continuez à utiliser l'appareil dans ces conditions.
Ne démontez pas et ne modifiez pas l'appareil
N'ouvrez pas le boîtier de cet appareil. Celui-ci contient des composants
haute tension ; si vous les touchez, vous risquez de vous électrocuter.
Contactez votre revendeur si une inspection ou un entretien de l'intérieur
de l'appareil est nécessaire.
Ne modifiez pas cet appareil. Sinon, vous risquez de provoquer un incendie ou un dysfonctionnement de l'appareil, ou vous pourriez vous électro-
cuter.
Ne placez ni eau ni substance chimique sur
l'appareil
Pour éviter tout risque d'incendie ou d'électrocution, ne placez pas de
vase contenant de l'eau, de boissons, de produits cosmétiques ni aucun
autre récipient contenant des substances chimiques ou de l'eau sur cet
appareil.
Débranchez l'appareil de la prise secteur en cas
d'orage
Si un orage est proche, mettez l'appareil hors tension, déconnectez la
fiche de la prise secteur et n'utilisez plus l'appareil. Un orage risque de
provoquer un incendie ou une électrocution.
Eloignez l'appareil de toute source de chaleur ou
des flammes
Eloignez l'appareil et son câble d'alimentation de l'installation de chauffage : le revêtement du boîtier de l'appareil ou de son câble d'alimentation pourrait fondre ; un incendie ou une électrocution risquent ainsi de se
produire.
N’utilisez pas l’appareil à des niveaux de volume
élevés pendant une longue période
L’utilisation de l’appareil à des niveaux de volume élevés avec le casque
ou les haut-parleurs pendant une longue période peut provoquer des
dommages auditifs permanents en fonction du réglage du volume de
sortie.
Ne placez pas l'appareil dans un endroit soumis à
une humidité excessive
N'utilisez pas cet appareil dans un endroit soumis à une humidité excessive, comme près d'une baignoire ou d'un humidificateur d'air, ne l'utilisez pas non plus sous la pluie ni à proximité d'un plan d'eau. Vous risqueriez de provoquer un incendie ou de vous électrocuter.
Ne bloquez pas l'orifice de ventilation
Etant donné que l'arrière de l'appareil fait office d'orifice de ventilation,
vous devez l'éloigner suffisamment du mur. Bloquer l'orifice de ventilation
retient la chaleur dans l'appareil, ce qui risque de déclencher un incendie.
Ne placez pas l'appareil dans un endroit soumis à
une température excessive
Ne placez pas l'appareil dans un endroit soumis à une température excessive, par exemple en plein soleil ou à proximité d'une source de chaleur, telle qu'un poêle ou un radiateur. Ceci risquerait d'augmenter la température interne et de provoquer un incendie.
Ne soumettez pas l'appareil à des projections
d'huile ou à de la vapeur
Ne placez pas cet appareil dans un endroit soumis à des projections
d'huile ou à de la vapeur. Vous risqueriez de provoquer un incendie ou de
vous électrocuter.
Veillez à ne brancher l'appareil que dans une prise
secteur d'une tension correcte
Cette tension est indiquée sur l'appareil. Si la tension n'est pas correcte,
vous risquez de provoquer un incendie ou de vous électrocuter.
N'utilisez pas cet appareil avec des mains humides
Ne connectez pas ni ne déconnectez le câble d'alimentation avec les
mains humides. Vous risquez de vous électrocuter.
Faites attention en manipulant la fiche
Lorsque vous débranchez le câble, veillez à le saisir par la fiche. Si vous
tirez sur le câble, vous risquez de l'endommager, de provoquer un incendie ou de vous électrocuter.
N'utilisez pas de branchements multiples
N'utilisez pas de rallonges, de multiprises ou d'adaptateurs pour créer un
branchement multiple partant d'une prise secteur. Vous risqueriez de provoquer un incendie ou de vous électrocuter.
Faites attention en manipulant le câble
d'alimentation
Veillez à ce que le câble ne soit pas griffé, endommagé, plié de manière
excessive, tordu ou emmêlé, qu'il ne subisse aucune modification, ne
tirez pas non plus dessus. Placer des objets lourds sur le câble ou le
soumettre à une chaleur excessive risque de l'endommager, de provoquer un incendie ou vous pourriez vous électrocuter. Contactez votre revendeur si le câble est endommagé.
N'utilisez cet appareil que dans le pays où vous
l'avez acheté
Cet appareil ne doit être utilisé qu'à la tension secteur du pays dans lequel il a été acheté ; ne l'utilisez pas dans un autre pays.
Attention
Déconnectez le câble d'alimentation lorsque vous
vous absentez
Si vous n'utilisez pas l'appareil pendant une période prolongée, décon-
nectez la fiche de la prise secteur pour plus de sécurité.
Ne laissez pas tomber l'appareil et ne le soumettez
à aucun choc physique
Ne laissez pas tomber cet appareil et ne le soumettez à aucun choc physique violent.
Vous risqueriez de le casser ou d'entraîner un dysfonctionnement.
Ne placez pas l'appareil dans un endroit instable
Ne placez pas l'appareil sur un support instable ou sur un angle. Il risque
d'être déséquilibré et de basculer, voire de tomber ; il pourrait alors être
endommagé ou vous pourriez vous blesser.
FRANÇAIS
53
Tutoriel
Cette section présente les procédures étape par étape de branchement
de votre amplificateur, de création de sons, d'enregistrement ou de
réinitialisation des sons créés et d'utilisation de modèles de rythmes.
Après vous être familiarisé avec ces procédures, vous maîtriserez presque toutes les opérations du MIMX.
Les illustrations ci-après proviennent du panneau de commande du MIMX
150H.
1. Connexions
FRANÇAIS
1)-a Lisez attentivement les précautions d'utilisation avant d'installer l'amplificateur. Connectez ensuite l'entrée CA 12 située sur le panneau ar-
rière à une prise électrique.
Remarque : Le son (et plus particulièrement la réponse basse fréquence)
de l'amplificateur dépendra de l'emplacement et des conditions d'installation de l'amplificateur.
1)-b Si vous utilisez le MIMX 150H, connectez la prise 14 SPEAKER
OUT à la prise d'entrée 4 Ω de votre enceinte. Pour ce faire, utilisez un
câble d'enceinte. Les enceintes de la série Ibanez IS possèdent deux
entrées. Utilisez celle portant l'indication MONO 4 Ω.
2) Raccordez votre guitare à la prise 1 INPUT. Utilisez un câble blindé
pour réaliser les connexions.
3) Si vous utilisez un appareil d'effet compact, connectez-le entre votre
guitare et l'amplificateur à l'aide d'un câble blindé.
4) Vérifiez que la commande de volume 10 MASTER est réglée sur 0 et
mettez sous tension le commutateur 11 POWER. L'animation de dé-
marrage s'affiche et l'amplificateur est prêt à l'emploi.
Remarque : N'oubliez pas de régler la commande de volume 10 MASTER
sur 0 et de mettre le commutateur 11 POWER hors tension dès que
vous n'utilisez plus l'amplificateur.
● Si vous utilisez l'IFC2
En connectant l'IFC2 en option (vendue séparément), vous pouvez accéder aux cinq effets de pédale supplémentaires. Pour en savoir plus
sur la réalisation des connexions, consultez le manuel d'utilisation de
l'IFC2.
54
2. Création de votre son
Découvrez comment créer quelques sons. Dans cet exemple, le modèle
n° 11 appelé PSYCHO est utilisé.
1) Dans la section mémoire 3, touchez le commutateur MANUAL
pour sélectionner le mode manuel dans lequel tous les réglages
audio sont conformes à la position réelle des commandes.
2) Réglez la commande de volume 10 MASTER entre 8 et 12
heures.
3) Réglez la section préamplificateur 2 comme suit.
Remarque : Cet amplificateur
peut produire des volumes sonores extrêmement élevés. Ré-
glez la commande de volume
MASTER de sorte à ne pas dé-
ranger le voisinage.
Il en résultera une légère distorsion audio. A présent, ajoutez quelques
effets.
4) Ajoutez tout d'abord l'effet 7 MODULATION. Pour ce faire, procédez
comme suit.
FX TYPE&PARAMETER:FLANGER 15
FX MIX LEVEL :20
*Le modèle de l'illustration ci-dessus est le
MIMX 150H.
TAP TEMPO :10
5) Ajoutez ensuite l'effet 8 DELAY&REVERB. Pour ce faire, procédez
comme suit.
FX TYPE&PARAMETER:REVERB HL 10
FX MIX LEVEL :30
TAP TEMPO :1
*Le modèle de l'illustration ci-dessus est le
MIMX 150H.
Vous remarquerez que le son devient plus ample. Lancez-vous à pré-
sent en essayant de créer vos propres sons de la même façon. Vous
apprendrez ensuite à enregistrer un son que vous avez créé.
* Consultez " A propos du
commutateur TAP "
ultérieurement dans ce
manuel.
Remarque : Le commutateur TAP
est sensible à la moindre pression
même légère. Appuyer dessus trop
fortement pourrait l'endommager.
Par conséquent, veuillez l'effleurer
avec délicatesse.
10
3. Enregistrement d'un son que vous avez créé
Dans cette section, vous allez apprendre à enregistrer un son que vous
avez créé. Vous enregistrerez ce nouveau son sur le canal 1 de la banque A.
* Pour plus de détails sur l'initialisation de la mémoire, consultez 5. Restauration des réglages d'usine par défaut
1) Assurez-vous que M s'affiche à l'écran 5, puis maintenez enfoncé le
commutateur " 1 " pendant au moins 3 secondes. Une fois les réglages
enregistrés, A1 apparaît sur l'écran 5 et clignote.
Remarque : Chaque canal comprend deux banques, A et B. Si vous
souhaitez enregistrer les réglages sur le canal 1 de la banque A
comme décrit dans ce didacticiel après avoir créé votre son en mode
manuel, vous devez appuyer sur " 1 ", vérifier que vous êtes dans la
banque A et toucher de nouveau le commutateur MANUAL pour revenir en mode manuel avant de procéder comme suit.
4. Utilisation de modèles de rythmes
Cette section vous explique comment utiliser des modèles de rythmes.
1) Commencez par jouer un rythme. Pour ce faire, touchez le commutateur
ON/OFF. Le commutateur TAP clignote et des sons de batterie sont audibles.
Remarque : Utilisez la molette RHYTHM pour ajuster le volume en conséquence.
2) Modifiez à présent le modèle. Appuyez sur + ou - jusqu'à ce que 16
s'affiche à l'écran 5.
3) Augmentez légèrement le tempo. Touchez le commutateur TAP plusieurs fois suivant le même rythme jusqu'à ce que 120 s'affiche à l'écran
5
.
FRANÇAIS
Maintenir enfoncé pendant au moins trois secondes.
Vous pouvez enregistrer sur n'importe quel canal un son créé en mode
manuel comme expliqué dans cette section. Un son créé dans chaque
banque peut être enregistré sur un canal de cette banque.
Voici un exemple.
2) Jusqu'à présent, vous avez utilisé le canal 1 de la banque A pour
créer un son. Vous allez désormais ajuster légèrement le réglage de
chaque commande et enregistrer le résultat sur le canal 2 de la banque
A. Procédez comme suit.
Modifiez le son du canal 1
de la banque A
Maintenez enfoncé pendant
au moins trois secondes.
Le son est enregistré
sur le canal 2 de la
banque A.
En enregistrant le son modifié sur un autre canal, vous serez en mesure
de comparer les deux sons. Essayez à présent d'utiliser des modèles
de rythmes.
Jouez un modèle de
rythmes
Modifiez le modèle de
rythmes
Modifiez la vitesse du
rythme
Vous pouvez utiliser des modèles de rythmes en procédant comme suit.
5. Restauration des réglages d'usine par défaut
Cette section vous explique comment réinitialiser l'amplificateur pour
restaurer les réglages d'usine par défaut.
1) Tout en maintenant le commutateur MANUAL enfoncé comme illustré
ci-après, mettez sous tension l'interrupteur 11 POWER. AL s'affiche à
l'écran 5.
2) Si vous appuyez sur le commutateur MANUAL dans cet état, toutes
les données sont réinitialisées sur les réglages d'usine par défaut.
3) Si vous décidez d'annuler sans réinitialisation, n'utilisez aucune commande hormis le commutateur MANUAL. Vous quittez le mode de restauration des réglages d'usine par défaut.
Tout en maintenant enfoncé
le commutateur MANUAL
enfoncé, mettez sous tension
l'interrupteur POWER.
Section préamplificateur : Cette fonction permet de contrôler la tonalité de la guitare.
2
Chaque section est détaillée ci-après.
1) AMP SELECTION : Cette molette vous permet de choisir parmi onze types de modèle
de préamplification. Pour en savoir plus, consultez la section décrivant les diverses
préamplifications.
2) GAIN : Cette molette de commande permet de régler le gain. La plage de réglage
dépend du réglage de la fonction AMP SELECTION. Suivant le niveau de la fonction
FRANÇAIS
GAIN, la valeur qui s'affiche à l'écran 5 est comprise entre 0 et 100.
3) Egaliseur : Il s'agit des molettes de commande des niveaux (BASS, MIDDLE, TREBLE)
de l'égaliseur à trois bandes. La plage de réglage et la fonction diffèrent suivant le réglage
de la fonction AMP SELECTION. Suivant le niveau, la valeur qui s'affiche à l'écran 5 est
comprise entre -15 et 15.
4) VOLUME : Cette molette de commande permet de régler le niveau de sortie du préam-
plificateur. Suivant le niveau de la fonction VOLUME, la valeur qui s'affiche à l'écran
est comprise entre 1 et 50. Le niveau de sortie dépend du type d'amplification sélection-
née, du niveau de gain et du niveau de l'égaliseur. Vous pouvez utiliser cette commande
pour maintenir un niveau cohérent entre les canaux, ainsi que pour spécifier le niveau
souhaité. Le volume final est réglé au moyen de la commande 10 MASTER volume.
Section mémoire : Pour enregistrer un son que vous avez créé, maintenez enfoncé le
3
commutateur du canal de destination d'enregistrement souhaité pendant au moins trois
secondes. Les détails sont présentés ci-après
1) MANUAL : Ce commutateur permet de sélectionner le mode manuel dans lequel tous les
réglages audio sont conformes à la position réelle des commandes. M s'affiche à l'écran 5.
2) Canaux (1-5) : Ces commutateurs choisissent l'un des cinq canaux sur lesquels vous pouvez enregistrer vos propres paramètres. Deux banques (A et B) sont disponibles et vous permettent d'enregistrer jusqu'à 10 sons. Au lieu de les sélectionner à partir du panneau avant,
vous pouvez connecter la pédale de réglage IFC2 en option (vendue séparément) et sélec-
tionner le canal à l'aide de votre pied. Le numéro du canal (1-5) s'affiche à l'écran 5.
3) Commutateur de sélection de la banque A/B : Deux banques contenant cinq canaux chacune sont disponibles.
Section batterie : Vous pouvez utiliser cinquante modèles de rythmes.
4
*Le modèle de
l'illustration ci-dessus
est le MIMX 150H.
56
1) Molette RHYTHM : Cette molette contrôle le volume de la batterie.
2) ON/OFF : Ce commutateur permet d'activer/désactiver le modèle
de rythmes.
3) -/+ : Ces commutateurs vous permettent de sélectionner l'un des cinquante différents modèles de rythmes. Pour en savoir plus sur chaque
modèle, consultez les SPECIFICATIONS.
4) Commutateur TAP : Ce commutateur contrôle la vitesse du rythme
suivant une plage de 40 à 199 BPM.
Ecran : Diverses opérations sont affichées ici.
5
TUNER ON/OFF : Le MIMX intègre un tuner chromatique. Les illustrations ci-après pré-
6
sentent les informations affichées à l'écran lorsque le tuner est utilisé.
Allumé pour indiquer un bé-
mol
Mouvement
de l'écran
Lorsque la hauteur
est faible
Section MODULATION : Cette fonction vous permet de contrôler quatre types d'effets de
7
modulation.
1) Molette FX : Cette molette de commande vous permet de choisir parmi les quatre
5
types d'effet de modulation suivants :
*Le modèle de
l'illustration ci-dessus
est le MIMX 150H.
2) Molette MIX : Cette molette contrôle le niveau de mixage de l'effet de modulation dans
une plage de 0 à 100. Sur 0, l'effet est désactivé et aucune modulation n'est appliquée.
3) Commutateur TAP : Ce commutateur contrôle la vitesse de modulation dans une plage
de 1 à 50. Le tableau suivant présente la vitesse de modulation contrôlable par le commutateur TAP de chaque mode.
Pour en savoir plus sur le TAP, consultez " A propos du commutateur TAP ".
Remarque : Si vous utilisez l'effet PEDAL PITCH de la section 9 PEDAL FX, vous ne
pouvez pas utiliser les effets de la section MODULATION.
Lorsque la hauteur est
correcte : mi bémol
a CHORUS : Cet effet crée un son riche en superposant les sons et en
les modulant. La molette FX vous permet de régler la profondeur de
modulation dans une plage comprise entre 0 et 100.
b FLANGER : Cet effet applique une modulation et un balayage au son.
La molette FX vous permet de régler la profondeur de modulation dans
une place comprise entre 0 et 100.
c VIBRATO : Cet effet applique un vibrato. La molette FX vous permet de
régler la profondeur de modulation dans une place comprise entre 0 et
100.
d STEP : Cet effet modifie le son de manière progressive. La molette FX
vous permet de régler la profondeur de modulation dans une place comprise entre 0 et 100.
Section DELAY & REVERB : Cette fonction vous permet de contrôler quatre
effets Delay&Reverb différents.
1) Molette FX : Cette molette de commande sélectionne l'un des quatre effets Delay&Reverb. Ces effets sont les suivants.
2) Molette MIX : Cette molette contrôle le niveau de mixage de l'effet
Delay&Reverb dans une plage de 0 à 100. Sur 0, l'effet est désactivé et
aucun effet Delay&Reverb n'est appliqué.
3) Commutateur TAP : Combiné à l'effet DELAY ou ECHO, ce commutateur
contrôle la durée du retard. Combinéà l'effet REVERB, ce commutateur con-
trôle la longueur de la réverbération. Le tableau suivant indique le temps de
retard et le temps de réverbération que le commutateur TAP permet de con-
a DELAY : Cet effet ajoute une copie retardée du son original,
quelque chose comme un " cycle musical ". Utilisez la molette
FX pour régler la rétroaction dans une plage de 0 à 40.
b ECHO : Cet effet produit un effet DELAY plus chaud. Utilisez la
molette FX pour régler la rétroaction dans une plage de 0 à 40.
c REVERB HL : Cette réverbération simule l'acoustique d'un
vaste espace comme une salle de concert. Utilisez la molette
FX pour régler le caractère de la réverbération dans une plage
de 0 à 10.
d REVERB RM : Cette réverbération simule l'acoustique d'un
espace confiné comme une pièce. Utilisez la molette FX pour
régler le caractère de la réverbération dans une plage de 0 à 10.
trôler dans chaque mode.
Temps
Contenu
à l'écran
Pour en savoir plus sur TAP, consultez " A propos du commutateur TAP ".
Remarque : Vous ne pouvez pas utiliser l'effet REVERB avec la section bat-
4
.
terie
Section PEDAL FX : Vous pouvez contrôler les effets de type pédale au moyen
de la pédale de réglage IFC2 en option (vendue séparément). Pour en savoir
plus, consultez " En savoir plus sur la pédale de réglage ".
1) Commutateur SELECT : Ce commutateur permet de sélectionner l'un des
cinq types d'effet de pédale. Ces effets sont les suivants.
a VOL PEDAL : Cette pédale de volume vous permet de
contrôler le volume à l'aide de la pédale.
b RING MOD : Cet effet confère un caractère métallique
au son.
c AUTO RESO : Cet effet règle la fréquence de réso-
nance suivant l'intensité de la sélection.
d WAH WAH : Il s'agit d'un effet wah-wah.
e PEDAL PITCH : Cet effet vous permet de régler la hauteur en temps réel.
1~30
2) Molette de commande : Cette molette contrôle l'effet de la section
PEDAL FX. Les effets disponibles dans chaque mode sont les suivants.
Position minimale Positions maximale
3) Prise du commutateur au pied : Vous pouvez utiliser le commutateur au
pied en connectant l'IFC2 vendue séparément.
4) Prise de la pédale : Vous pouvez utiliser la section
nectant l'IFC2 en option (vendue séparément).
10
MASTER volume : Cette commande contrôle la sortie finale transmise aux
enceintes.
11
Commutateur POWER : Il s'agit de l'interrupteur d'alimentation de l'amplifi-
9
PEDAL FX en con-
cateur.
12
Entrée AC : Branchez-y le câble d'alimentation fourni.
13
LINE OUT (MIMX 150H) : Il s'agit de la prise de sortie du niveau de ligne.
14
SPEAKER OUT (MIMX 150H) : Il s'agit de la prise de sortie des enceintes.
Utilisez un câble d'enceintes pour brancher un système d'enceintes 4 Ω ou
8 Ω.
Remarque : Si vous utilisez un système d'enceintes dont l'impédance est
inférieure à 4 Ω, (par exemple un système d'enceintes 2 Ω), l'amplificateur
de puissance surchauffe, ce qui active un circuit de protection et rend impossible l'obtention du son voulu à la sortie.
15
HEADPHONES (MIMX65) : Il s'agit d'une prise de sortie pour casque.
16
CD INPUT (MIMX65) : Il s'agit de la prise d'entrée de niveau de ligne. Vous
pouvez y brancher un lecteur de CD portable ou un lecteur de MP3.
9
FRANÇAIS
57
AMP SELECTION
Le cadran AMP SELECTION permet de choisir parmi onze types de
préamplis. Parmi les nombreux amplis pour guitare du marché, Ibanez
s’est concentré sur les sons de dix amplis classiques particulièrement
appréciés des guitaristes. De l’entrée de la guitare à la sortie de l’enceinte, chaque élément a été analysé et mémorisé sous forme de
préampli. La console MIMX est conçue de manière à obtenir facilement
des sons identiques à ces amplis. L’égalisation de chaque préréglage
prend en considération le son global de l’ampli échantillonné, y compris
FRANÇAIS
la réaction en cas d’utilisation (ou non) de commandes telles que
"Presence", "Bright", "Resonance" ou "Deep", permettant à chaque
modèle d’obtenir des instantanés de tonalités classiques étonnamment
détaillés. En aucune façon, il ne s’agit de répliques exactes, mais plutôt
d’une "coloration" particulière. Pour obtenir un son Ibanez original fort,
sec et régulier, utilisez le numéro de sélection 11, appelé à juste titre
"Psycho".
REMARQUE : dans les descriptions de préamplis suivantes, nous avons
utilisé des noms de produits non Ibanez afin de vous donner des références de tonalité compréhensibles et familières et d’indiquer les types
de sons amplifiés qui ont inspiré les réglages de la console MIMX. Ces
références et comparaisons aux produits non Ibanez sont purement
subjectives. Ibanez ne prétend en aucun cas que les préamplis MIMX
constituent des représentations exactes des amplis auxquels il est fait
référence. Cela dit, nous sommes certains que vous apprécierez les
sons produits grâce au large choix de tonalités proposées par la nouvelle console MIMX.
60s Clean :
Ce préréglage a été créé pour faire revivre le son de l’un des amplis
classiques fabriqués par Fender®, le ’65 Twin Reverb®, utilisé sur le
canal NORMAL en désactivant le commutateur BRIGHT. La référence
aux sons purs des années 1960 évoque à tout un chacun cet ampli. La
conception sonore de ce préampli met l’accent sur la netteté éclatante
des aigus et la solidité des basses, rappelant les sons classiques des
années 1960, mais elle offre toujours un son agréablement unique.
Jazz Combo :
Cette sélection a été inspirée par le Roland® JC-120, célèbre pour sa
capacitéà reproduire le son simple de la guitare lorsqu’il est utilisé sur
le canal 1 en désactivant le commutateur BRIGHT et en atténuant la
tonalité globale. La gamme étendue et le son incolore de ce préampli
sur des fréquences aigues et basses est une association parfaite pour
les processeurs d’effet afin de créer une sélection hautement polyvalente.
70s Brit :
Il s’agit d’un son inspiré du modèle classique "JCM800 2203" de Marshall® associéà l’effet overdrive produit lorsque le TUBESCREAMER®/
TS-9 d’Ibanez® est utilisé comme ampli. Ce préampli couvre un large
éventail de sons créatifs, des accords puissants aux solos fracassants.
Brit Blues :
L’histoire de l’"AC30" de VOX® ressemble à plus d’un titre à l’évolution
musicale du blues, du rock et de la pop. Comme sa célébrité n’a cessé
de croître jusqu’à aujourd’hui et qu’il reste toujours apprécié d’un grand
nombre de musiciens, nous pensons qu’un préampli influencé par ce
type de son est tout simplement une évidence. Lors de la conception de
ce son pour la console MIMX, nous l’avons équipé de fréquences moyen-
nes particulièrement vives et d’une certaine rigueur qui améliorent la
tonalité classique. Les nuances des accords sont transmises fidèlement,
vous permettant ainsi de profiter d’une large variété de tonalités.
58
US Blues :
Cette sélection nous rappelle réellement le "Hot Rod Deville™" de
Fender® utilisé sur le canal DRIVE en réglant le commutateur BRIGHT
sur NORMAL et en activant la commande MORE DRIVE. La console
MIMX renforce les basses de ce son et règle l’égalisation sur un style
progressif. Un son clair aux résonances exceptionnellement puissantes
constitue l’attrait particulier de cette sélection. D’un son peu amplifié qui
met en valeur les tonalités puissantes à l’overdrive exceptionnel que
vous obtenez en augmentant l’amplification, ce préampli propose un
vaste choix de tonalités.
Rock :
Cette sélection reproduit le son de l’"Ecstasy 101B EL34 Version", un
ampli à tubes multifonction fabriqué par Bogner Corporation, célèbre
pour ses amplis artisanaux. La réponse des réglages fournit une plage
dynamique améliorée du gain faible au gain élevé en augmentant le
niveau de la commande EQ. Apprécié sa tonalité nette, ce réglage offre
une large gamme de sons (doux, purs et puissants) ainsi que des effets
overdrive soutenus.
Hard Rock :
D’abord uniquement réservéà quelques musiciens comme amplis personnalisés, le modèle "SL0-100" de Soldano’s® a réussi à remporter un
plus franc succès et une certaine renommée. Nous avons créé cette
sélection pour se rapprocher du son produit par le canal OVERDRIVE
du SLO-100 lorsque le commutateur BRIGHT est réglé sur NORMAL,
mais nous avons réduit le risque d’effet Larsen grâce à une tension et
une rigueur globales. Nous estimons que le son amplifié est particuliè-
rement appréciable et représente le choix idéal pour les leads ou les
riffs heavy.
Guitar God :
Nous dressons ici le portrait du son émis par le "5150 II®" de Peavey®.
En créant ce préampli MIMX, nous avons à la fois écouté l’ampli Peavey
réel et les sources audio utilisées sur un CD afin de reproduire des sons
qui parviendront à vos oreilles avec des tonalités de disques. Les basses bien maîtrisées conviennent parfaitement aux riffs qui intercalent
des notes étouffées, et la distorsion rendra le sustain de vos solos inoubliable.
90s Brit :
La conception de ce préampli s’est également basée sur un ampli, en
l’occurrence le modèle "JCM2000 DSL100" de Marshall®, et sur les
sources audio CD réelles d’un groupe qui a l’utilisé. La reproduction du
son crée une distorsion brute, mais le son est tendu et bien défini et les
notes idéalement séparées, ce qui en fait un outil utilisable tant pour les
arpèges éclatants que pour les riffs tapageurs. C’est garanti, le son de
votre guitare se distinguera même dans un groupe puissant.
LA Heavy :
Le "Dual Rectifier® Solo Head" de Mesa/Boogie® a influencé bon nombre de musiciens de heavy metal. Ce préampli est notre interprétation
d’un assemblage de sons classiques d’un modèle présenté en 1989,
modèle qui a déterminé la sonorité de la guitare heavy moderne. Notre
version reproduit la distorsion des tubes de puissance originaux 6L6
dans le canal RED alimenté en mode BOLD, passant par le redresseur
aux diodes de silicium, avec sortie sur une enceinte 4x12 Ibanez®
Thermion® TN412A. Résultat : basses colossales et crunch remarquable.
Psycho :
Son Ibanez original conçu pour le courant dominant de la scène heavy
rock actuelle. Il est caractérisé par des basses tendues et nettes et une
superbe précision. En réglant l’égalisation, vous pouvez utiliser ce son
dans n’importe quel style musical.
* A l’exception des modèles Ibanez® TUBESCREAMER® et
Thermion®, les noms de sociétés et de produits mentionnés dans ce
manuel sont les marques commerciales ou les marques déposées
de leurs détenteurs respectifs et ne sont pas affiliés à Ibanez.
Fender®, Twin Reverb®, Hot Rod Deville™ sont des marques dépo-
sées ou des marques commerciales de Fender Musical Instruments
Corporation.
Roland® est une marque déposée de Roland Corporation.
Marshall® est une marque déposée de Marshall Amplification PLC.
VOX® est une marque déposée de VOX R&D limited.
Soldano® est une marque déposée de Soldano Custom Amplification.
Peavey® est une marque déposée de Peavey Electronics LTD.
5150 II® est une marque déposée de E.L.V.H., Inc.
Mesa/Boogie® et Dual Rectifier® sont des marques déposées de
Mesa/Boogie, Limited.
FRANÇAIS
59
Préréglages d'usine par défaut
Il s'agit des réglages audio de chaque canal A1à B5 du MIMX à sa
sortie de l'usine. Par une simple pression sur ce bouton, vous obtiendrez les combinaisons de sons et d'effets propres au MIMX.
A1 : Immortal Shred
AMP SELECTION : Psycho
Ce préréglage est idéal pour les riffs rapides propres aux groupes de
slash metal ou de death metal de la scène musicale actuelle. La plage
centrale est coupée pour mettre en valeur les plages haute et basse et
FRANÇAIS
un son ferme et robuste est créé en augmentant les graves sans réduire
la plage centrale de manière excessive.
A2 : Shrapnel Heroes
AMP SELECTION : Psycho
Ce préréglage peut être utilisé pour les solos à la guitare dans de nombreux styles musicaux, du hard rock au heavy metal. L'égaliseur est
relativement plat. Si vous ajoutez un retard assez rapide, ce préréglage
confèrera un son agréable aux solos.
A3 : Cruel Heaviness
AMP SELECTION : 90s Brit
Ce préréglage est dédié aux riffs mettant le rythme en valeur. Il est parfait pour les chansons dont le tempo est lent. Par ailleurs, la plage basse
accentuée permet l'obtention d'un son de forte distorsion regroupant les
sons de tout le groupe. Parfait pour les sons loud rock de la scène musicale actuelle.
A4 : Legend of the Beast
AMP STYLE : Hard Rock
Il s'agit d'un préréglage de guitare solo du son Metal classique des années 80. Ce préréglage possède un caractère audio suggérant l'âge
d'or du Metal propre à de nombreux groupes Metal anglais et améri-
cains.
A5 : Emotional Clean
AMP STYLE : 60s Clean
Ce préréglage vous permet d'obtenir des graves épais, un caractère sec
et un effet de réverbération pour créer une atmosphère chaleureuse. En
utilisant un micro à simple bobinage, vous pouvez créer un excellent
son classique. En diminuant le niveau de mixage de l'effet de réverbéra-
tion, vous pouvez mettre en valeur le sens d'attaque.
B1 : Sounds of the Right Hand
AMP SELECTION : Guitar God
Ce préréglage est idéal pour les riffs forts ou légers mais également
pour les leads. La distorsion obtenue en augmentant le GAIN au maximum et la plage moyenne dynamique conviennent parfaitement aux
micros à double bobinage. Un flanger est légèrement appliqué pour ajouter une dynamique, et un retard est ajouté pour créer un effet spatial.
B2 : Purple Tone
AMP SELECTION : Rock
Il s'agit d'un réglage du gain élevé qui coupe largement les graves et
ajoute un caractère distinctif à la plage centrale. En utilisant un micro à
simple bobinage, vous pouvez recapturer les sons des années 70. En
augmentant la commande MIDDLE, le son apporte une atmosphère classique que vous pouvez régler selon vos préférences. Pour profiter pleinement de ce son, jouez les riffs de hard rock qui ont révolutionné leur
époque et qui sont à l'origine du heavy rock actuel.
B3 : Crystal Clean
AMP SELECTION : Jazz Combo
Ce préréglage a été conçu pour produire des sons propres éclatants et
cristallins. Il est particulièrement adapté au ballades hard rock et heavy
metal des années 80 et 90. Essayez ce préréglage avec des micros à
simple bobinage (micro central ou miros de manche/moyens). Augmentez le niveau de mixage des effets pour obtenir un son plus généreux.
B4 : Solo DNA
AMP SELECTION : Rock
Ce préréglage a été créé pour vous permettre de jouer ces solos destructeurs rendus célèbres par les guitaristes de légende des années 80 ! Ce
réglage est idéal pour vous éclater sur votre guitare ! Utilisez librement
les flexions de corde, le dive bombing, les pinch harmonics et les sweep
arpeggios et laissez libre cours à votre imagination.
B5 : Samurai Edge
AMP SELECTION : 70s Brit
Ce préréglage est excellent pour les riffs d'accompagnement (comping)
ou de type blues joués avec un micro à simple bobinage. Il possède la
distorsion adéquate pour accentuer les nuances de votre sélection et
offre une netteté finale agréable. Réglez la réverbération à votre convenance.
60
Utilisation du commutateur TAP
Le MIMX intègre un commutateur TAP que vous pouvez utiliser pour
contrôler la vitesse des effets et du rythme. Ceci vous semblera peutêtre un peu difficile au début mais vous l'utiliserez rapidement en toute
simplicité et de manière intuitive.
En touchant (effleurant) ce commutateur à plusieurs reprises (et pas
seulement deux fois), vous pouvez modifier la vitesse souhaitée. Si vous
continuez de le toucher, l'intervalle moyen s'affiche à l'écran 5.
Pour en savoir plus sur l'aspect technique de cette fonction, consultez la
description détaillée de la détection du tempo moyen par la fonction TAP
ci-après.
Moyenne de mouvement
Cette méthode est utilisée pour déterminer la vitesse du tempo via le
commutateur TAP. Par exemple, si vous souhaitez régler le tempo de la
batterie sur 120 BPM, il est assez difficile de spécifier le tempo précis en
touchant simplement le commutateur TAP deux fois.
Moyenne de déplacement à quatre valeurs (l'exemple suppose l'utilisation de qua-
tre valeurs)
La valeur moyenne des quatre dernières opérations du commutateur TAP fait office de valeur. Ceci permet d'absorber toutes les imprécisions liées au fonctionnement réel.
Valeur
1125bpm2115bpm3130bpm4109bpm
traitée
Valeur
de sortie
1
125bpm120bpm121bpm119bpm123bpm
(1+2)
2
Moyenne de déplacement à deux valeurs
Vous devez appuyer sur le commutateur TAP suivant un rythme
régulier de sorte que l'intervalle entre la première et la
deuxième pression du commutateur TAP soit de 60/120 secondes = 0,5 secondes.
(1+2+3)3(1+2+3+4)4(2+3+4+5)
Le MIMX utilise une moyenne de déplacement à sept valeurs. En marquant les pressions avec le commutateur TAP, vous pouvez obtenir un
réglage du tempo plus précis.
5131bpm
4
A propos de l'indication " currently edited " sur l'écran central
Le MIMX possède une DEL d'édition en cours qui s'allume comme illustré ci-après.
DEL d'édition en
cours
Position de
la molette
Position du son
actuel
sition différente de la valeur mémorisée, la DEL d'édition en cours dans
le coin inférieur droit de l'écran 5 l'indique en s'allumant. Lorsque vous
déplacez la commande sur la position correspondant à la valeur mémorisée, l'indication d'édition en cours disparaît. Cette valeur est celle en-
registrée sur le canal sélectionné.
Voici un exemple.
1) Appuyez sur A1.
2) Déplacez la commande GAIN sur 12 heures.
50 s'affiche à l'écran 5 et le point s'allume. Ceci
indique que le gain a été modifié et qu'il diffère de
la valeur de gain en mémoire.
3) Déplacez la commande GAIN en position maximale. 100 s'affiche à l'écran 5 et le point devient
noir. Ces informations indiquent que la valeur de
gain en mémoire est visible à l'écran 5.
* Toutes les commandes intègrent cette fonction. Vous pouvez l'utiliser
pour comparer les valeurs de contrôle stockées ou en vérifiant le contenu enregistré sur chaque canal.
* Si vous touchez le commutateur MANUAL pour sélectionner le mode
manuel, la position de chaque commande correspondra à la valeur réelle
du son.
Le MIMX intègre des molettes de type
analogique pour faciliter l'utilisation.
Cependant, lorsque vous appuyez sur
un commutateur de canal A1 à B5 pour
rappeler les réglages enregistrés, le
réglage du son rappelé pour les molettes situées sur le panneau avant ne
correspondra pas nécessairement à la
position physique des molettes. C'est
pourquoi, lorsque vous touchez un
commutateur de canal pour rappeler
des réglages en mémoire et que vous
déplacez une commande sur une po-
61
FRANÇAIS
En savoir plus sur la pédale de réglage
Vous pouvez utiliser la pédale de réglage IFC2 (vendue séparément)
séparément comme contrôleur du MIMX. Si vous connectez l'IFC2, vous
pourrez utiliser la section 9 PEDAL FX, et utiliser les commutateurs au
pied pour passer d'un canal à l'autre.
FRANÇAIS
a
e
d
b
f
c
A
B
Fonctionnement
a
Pédale : Contrôle l'effet de pédale sélectionné sur l'amplificateur.
Commutateur haut : Permet de passer de la mémoire supérieure à
b
la mémoire actuellement sélectionnée. (Ne fonctionne pas en mode
manuel.)
c
Commutateur bas : Permet de passer à la mémoire directement
inférieure à la mémoire actuellement sélectionnée. (Ne fonctionne
pas en mode manuel.)
Appuyez simultanément sur b et c pour activer le tuner.
d
Prise du commutateur au pied : Connectez-la à l'amplificateur pour
utiliser les commutateurs au pied.
e
Prise à effet de pédale : Connectez-la à l'amplificateur pour utiliser
l'effet de pédale. Un circuit dans l'IFC2 permet au MIMX de
reconnaître la pédale connectée.
Commutateur de mode : Ce commutateur détermine le
f
fonctionnement de la pédale. Réglez-le de manière adéquate suivant
votre style de jeu.
A
L'effet perdure même si la pédale est en position minimale
(complètement retournée vers vous).
B
L'effet est désactivé si la pédale est en position minimale
(complètement retournée vers vous).
62
Dépannage
Vérifiez d'abord que le câble blindé de guitare, le câble de haut-parleur et le
câble d'alimentation sont correctement connectés. Utilisez si possible un testeur
pour vérifier la connexion, ou un autre câble ou un autre amplificateur pour
vérifier l'état du câble.
1. Impossible de mettre l’amplificateur sous tension
• Vérifiez si le cordon d’alimentation est raccordé correctement.
• Essayez de le brancher à une autre prise secteur pour voir si le problème persiste.
2. L’amplificateur peut être mis sous tension mais ne
produit aucun son.
• Vérifiez si la guitare est raccordée correctement.
• Débranchez tout effet externe connecté à la boucle d’effets ainsi qu’entre la
guitare et l’ampli pour vérifier si la source du problème ne réside pas là.
• Utilisez un autre câble blindé pour voir si cela ne permet pas de résoudre le
problème.
• Vérifiez si le volume de la guitare n’est pas réglé sur "0".
• Branchez une autre guitare pour voir si cela résout le problème.
• Vérifiez si le volume de l’amplificateur n’est pas réglé sur "0".
• Vérifiez si le casque d’écoute est raccordé.
• Il n'y a toujours aucun son lorsque vous augmentez le volume principal?
• Si vous utilisez le contrôleur au pied IFC2 vendu séparément comme pédale de
volume, vérifiez que la pédale ne soit pas en position complètement fermée
(vers vous).
3. Le son de l’ampli comporte du bruit
• Vérifiez si l’amplificateur n’est pas installéà proximité d’une source de résonance
ou si le bruit ne provient pas d’un objet heurtant l’ampli.
• Vérifiez si le manchon de la fiche du câble blindé n’est pas lâche.
• Assurez-vous que l’action (hauteur des cordes) de votre guitare est réglée
correctement.
• Utilisez une autre guitare, un autre effet ou appareil externe et un autre câble
pour voir si cela ne permet pas d’éliminer le bruit.
4. Aucun son lorsque vous connectez un lecteur de CD
•
Assurez-vous que le volume du lecteur de CD n’est pas sur “0”.
• Assurez-vous que le câble est branché correctement.
• Essayez d'utiliser un autre câble pour vérifier qu'un son est émis.
5. Le son du CD n'est pas normal
Est-ce que le câble utilisé dispose d'une fiche stéréo ? Est-il possible que vous
utilisiez une fiche monophonique ?
6. Pas de son au casque d’écoute
• Vérifiez si le casque d’écoute est branché correctement.
• Raccordez un autre casque pour voir si le son est reproduit.
7. Aucun son de batterie
• Vérifiez que le volume de batterie ne soit pas réglé sur 0.
• Vérifiez que le volume principal ne soit pas réglé sur 0.
• Vérifiez que le casque ne soit pas connecté.
8. L'effet de modulation ne fonctionne pas
• Vérifiez que le niveau de mixage ne soit pas réglé sur 0.
• Vérifiez que l'accordeur intégré au MIMX ne soit pas en fonction.
• Si vous utilisez le contrôleur au pied IFC2 vendu séparément pour régler lacommande PEDAL PITCH, vérifiez sa fonction.
9. L'effet de retard ne fonctionne pas
• Vérifiez que le niveau de mixage ne soit pas réglé sur 0.
• Y a-t-il un changement lorsque vous utilisez la dérivation?
• Vérifiez que l'accordeur intégré au MIMX ne soit pas en fonction.
10. L'effet de réverbération ne fonctionne pas
• Vérifiez que le niveau de mixage ne soit pas réglé sur 0.
• Vérifiez que des changements se produisent lorsque vous utilisez la dérivation.
• Vérifiez que la fonction batterie soit désactivée.
• Vérifiez que l'accordeur intégré au MIMX ne soit pas en fonction.
11. Impossible d'utiliser la pédale d'effet
• Le contrôleur au pied IFC2 vendu séparément est-il connecté ?
• Utilisez-vous le câble fourni avec l'IFC2 ?
• Vérifiez que l'accordeur intégré au MIMX ne soit pas en fonction.
En cas d’anomalie
Cet appareil a subi une inspection rigoureuse avant sa sortie d’usine. Si
l’amplificateur vous semble présenter une anomalie, effectuez les opérations cidessus. Dans le cas peu probable où vous rencontreriez un problème pendant
l’utilisation, consultez votre revendeur. Par ailleurs, lorsque vous envoyez
l’amplificateur en réparation, veillez à décrire correctement tous les symptômes
de la panne; cela permettra d’accélérer les travaux de réparation.
Nous nous réservons le droit de modifier les données techniques sans avis
préalable en vue d’améliorer ce produit.
FRANÇAIS
63
Prólogo
Gracias por adquirir el amplificador de guitarra Ibanez de la serie MIMX. MIMX
es un amplificador de modelado digital que refuerza los sonidos de alta calidad
suministrados por un procesamiento de señal a 32 bits. Para sacar el máximo
partido de las funciones que le ofrece este amplificador, antes de utilizarlo lea
antentamente este manual. Seguidamente guarde el manual en un lugar seguro.
Precauciones de uso
1) Lea las precauciones de uso que se facilitan en este manual.
2) Tenga a mano las precauciones de uso que se facilitan en este manual para
ESPAÑOL
consultarlas.
3) Observe todas las precauciones.
4) Siga las instrucciones que se facilitan en este manual.
5) Utilice únicamente un paño seco para limpiar el amplificador.
6) Este producto puede generar volúmenes extremadamente altos. En algunos
casos ello puede dañar los oídos o provocar otras lesiones. Debe tener cuidado
con el volumen cuando utilice este producto.
7) Verifique siempre que el sistema de altavoces que conecte al amplificador tenga
la impedancia correcta.
8) Utilice este producto con una fuente de alimentación cuyo voltaje sea igual al
indicado en el panel posterior.
9) Evite pellizcar o aplastar el cable de alimentación, especialmente junto al enchufe
o a la toma de corriente.
10)Sitúe este producto cerca de la toma de corriente principal y verifique que el
enchufe se pueda desconectar fácilmente de la misma en caso de que se
presente algún problema.
11)Utilice únicamente los elementos u opciones incluidos que cumplan las
especificaciones del fabricante.
12)Este aparato está protegido por un fusible. El fusible se puede romper debido a
un golpe externo o por haberse agotado su vida útil; no obstante, dado que la
rotura del fusible puede indicar que se ha producido un fallo interno grave,
consulte a su concesionario antes de cambiarlo.
13)Confíe todas las reparaciones a un técnico autorizado por el distribuidor. Será
necesario proceder a una revisión y reparación si el cable de alimentación o el
enchufe resultan dañados, si sale líquido de la unidad, si penetra un objeto
extraño en el interior de la unidad, si la unidad se moja, si se cae accidentalmente
o si no funciona con normalidad.
14)Cuando no utilice el amplificador, manténgalo apagado. Mientras el MIMX esté
conectado a una toma de corriente, no está completamente aislado de la fuente
de alimentación aún cuando el interruptor de alimentación esté desconectado.
Cuando no vaya a utilizar el MIMX durante largo tiempo, desenchufe el cable de
alimentación.
15)No apague el dispositivo ni lo desenchufe mientras lo esté utilizando. Ello puede
provocar averías.
16)No se suba al dispositivo ni coloque objetos pesados sobre el mismo. Se puede
romper o averiar.
64
Precauciones relativas a la ubicación
17)Si utiliza el MIMX sobre una caja acústica, deberá instalar el equipo de forma
segura en el piso o en una pared. Concretamente, si está utilizando dos cajas
acústicas (es decir, un apilado completo), cerciórese de colocar el equipo sobre
una superficie plana y nivelada, y utilice correas de seguridad, o sujetadores
similares, para fijar el equipo al piso o a la pared para evitar que se caiga.
18)No coloque este dispositivo en lugares en que las temperaturas puedan ser
muy bajas, por ejemplo cámaras frigoríficas. El dispositivo puede fallar.
19)No coloque este dispositivo en lugares expuestos a campos magnéticos
intensos, por ejemplo cerca de un televisor o una radio, o cerca de otro dispositivo
que emita radiaciones electromagnéticas. En esas condiciones el dispositivo
puede fallar.
20)No coloque el dispositivo en lugares expuestos a variaciones bruscas de
temperatura
Si el dispositivo se encuentra en un lugar frío y la temperatura sube rápidamente,
puede formarse condensación en su interior y provocar fallos.
21)No coloque el dispositivo en lugares expuestos a un exceso de polvo o
vibraciones
En tales condiciones pueden producirse daños o averías.
22)Según el lugar donde se coloque este dispositivo, puede provocar ruidos en
una radio próxima u oscilaciones o distorsión en la pantalla de un televisor
cercano. Si sospecha que este dispositivo está provocando dichas interferencias,
apáguelo. Si cuando apaga el dispositivo, la radio o el televisor vuelven a
funcionar con normalidad, aleje el dispositivo de la radio o del televisor o cambie
la orientación de estos.
ESPAÑOL
65
Precauciones de seguridad
Lea atentamente estas precauciones antes de utilizar este dispositivo y utilícelo
únicamente observando dichas precauciones.
Cuando haya leído las precauciones, guárdelas con el "Manual del propietario"
y la "Garantía".
Prevención de incendio, electrocución o daños personales
Símbolos gráficos
ESPAÑOL
indica un aviso (peligro o advertencia). El contenido
específico del aviso viene indicado en el interior del
triángulo. La figura que se muestra a la izquierda indica un
aviso general, advertencia o peligro.
indica una prohibición (algo que no se debe hacer). El
contenido específico de la prohibición viene representado
en el interior del símbolo. La figura que se muestra a la
izquierda indica que no se debe desarmar la unidad.
indica una acción obligatoria (algo que debe hacer). La
acción específica viene representada en el interior del
símbolo.
Advertencias
Si sale humo del dispositivo
Puede producirse un incendio o electrocución si continúa utilizando el
dispositivo en condiciones anómalas, por ejemplo si emite humo o un
olor inusual. Apague inmediatamente el dispositivo, desenchúfelo y
póngase en contacto con el distribuidor donde lo haya adquirido. No trate
nunca de reparar usted mismo el dispositivo, ya que puede ser peligroso.
Si el dispositivo se rompe
Si el dispositivo se cae o la caja acústica está dañada, apáguelo
inmediatamente, desenchúfelo y póngase en contacto con el distribuidor
donde lo haya adquirido. Puede producirse un incendio o electrocución si
continúa utilizando el dispositivo en estas condiciones.
Si un objeto extraño penetra en el dispositivo
Si un objeto extraño metálico o inflamable penetra en el interior de este
dispositivo a través de una toma u otra abertura, apáguelo
inmediatamente, desenchúfelo y póngase en contacto con el distribuidor
donde lo haya adquirido. Puede producirse un incendio o electrocución si
continúa utilizando el dispositivo en estas condiciones.
No desarme ni modifique el dispositivo
No abra la caja acústica de este dispositivo. Este dispositivo contiene
componentes de alta tensión que pueden provocar una descarga eléctrica
si los toca. Póngase en contacto con su distribuidor en caso de que
necesite revisar el interior o repararlo.
No modifique este dispositivo. Puede producirse un incendio, una descarga
eléctrica o averías.
No ponga agua o productos químicos sobre el
dispositivo
A fin de evitar el riesgo de incendio o descargas eléctricas, no coloque
floreros, bebidas, cosméticos o recipientes de productos químicos o agua
encima de este dispositivo.
Desenchufe el dispositivo en caso de tormenta
Si hay una tormenta cerca, apague el dispositivo, desenchúfelo y deje de
utilizarlo. Los rayos pueden provocar un incendio o descargas eléctricas.
No coloque el dispositivo cerca de una llama o una
fuente de calor
Mantenga el dispositivo y el cable de alimentación alejados de elementos
de calefacción. La caja acústica o el forro del cable de alimentación se
pueden fundir, con el consiguiente riesgo de incendio o descarga eléctrica.
No utilice el aparato a un volumen elevado durante
periodos prolongados
El uso del aparato a un volumen elevado con auriculares o altavoces
durante periodos prolongados puede provocar pérdida de audición
permanente según el volumen.
66
No coloque el dispositivo en lugares húmedos
No utilice este dispositivo en lugares húmedos, por ejemplo cerca de un
baño o un humidificador, bajo la lluvia o cerca de agua. Puede producirse
un incendio o una descarga eléctrica.
No obstruya las aberturas de ventilación
Dado que la parte posterior sirve de abertura de ventilación, debe haber
suficiente espacio entre el dispositivo y la pared. Si se obstruye la abertura
de ventilación puede acumularse calor en el interior del dispositivo, con
el consiguiente riesgo de incendio.
No coloque el dispositivo en lugares expuestos a
temperaturas altas
No coloque este dispositivo en lugares expuestos a temperaturas altas,
por ejemplo al sol o cerca de equipos que generen calor como estufas o
calefactores. Puede elevarse la temperatura interna del dispositivo, con
el consiguiente riesgo de incendio.
Evite exponer el dispositivo a salpicaduras de
aceite y al vapor
Evite colocar este dispositivo en lugares donde pueda quedar expuesto
a salpicaduras de aceite o a vapor. Puede producirse un incendio o una
descarga eléctrica.
Utilice este dispositivo únicamente con una toma
de CA del voltaje correcto
Este dispositivo se debe utilizar únicamente con una toma de CA del
voltaje correcto, el cual viene indicado en el propio dispositivo. Si se utiliza
este dispositivo con una toma de CA de voltaje incorrecto, puede
producirse un incendio o una descarga eléctrica.
No manipule el dispositivo con las manos mojadas
No enchufe ni desenchufe el cable de alimentación con las manos
mojadas. Puede recibir una descarga eléctrica.
Manipule el enchufe con cuidado
Cuando desenchufe el cable, hágalo tirando del enchufe. Si lo desenchufa
tirando del cable de alimentación, este puede resultar dañado, con el
consiguiente riesgo de incendio o descarga eléctrica.
Evite conectar varios cables a una sola toma de
corriente
No utilice alargadores múltiples, regletas de conexión o ladrones para
conectar varios cables a una única toma de CA. Puede producirse un
incendio o una descarga eléctrica.
Manipule el cable de alimentación con cuidado
Evite pelar, dañar, modificar, doblar excesivamente, estirar, retorcer o
reliar el cable de alimentación. Si coloca objetos pesados sobre el cable
de alimentación o le aplica calor, puede resultar dañado, con el
consiguiente riesgo de incendio o descarga eléctrica. Si el cable de
alimentación resulta dañado, póngase en contacto con su distribuidor.
Utilice este dispositivo únicamente en el país
donde lo ha comprado
Este dispositivo está diseñado para funcionar con el voltaje de corriente
alterna del país en el que lo ha comprado; no puede utilizarlo fuera de
dicho país.
Precauciones
Desconecte el cable de alimentación si va a estar
fuera
Por razones de seguridad, desenchufe el dispositivo si no va a utilizarlo
durante un periodo prolongado.
Evite que el dispositivo caiga o reciba golpes
Evite que el dispositivo caiga o reciba golpes fuertes.
Se puede romper o averiar.
No coloque el dispositivo en un lugar inestable
No coloque este dispositivo en un lugar inestable, por ejemplo un soporte
inseguro o en posición inclinada. Puede desequilibrarse y volcar o caer,
con el consiguiente riesgo de daños o lesiones.
ESPAÑOL
67
Guía
En esta sección se le explicará paso a paso cómo efectuar las conexiones al amplificador, crear sonidos, memorizar o recuperar sonidos que
haya creado y utilizar patrones de ritmo. Una vez haya seguido estas
explicaciones entenderá prácticamente todo el funcionamiento del MIMX.
Las ilustraciones que se muestran corresponden al panel de control del
MIMX 150H.
1. Conexiones
ESPAÑOL
1)-a Lea atentamente las precauciones de uso y luego prepare el amplificador. A continuación utilice el cable de alimentación que se incluye
para conectar la toma 12 AC INPUT a una toma de la red eléctrica.
Nota: El sonido (en particular la respuesta de bajas frecuencias) del
amplificador cambiará según la ubicación y las condiciones en que instale el amplificador.
1)-b Si va a utilizar el MIMX 150H, conecte 14 SPEAKER OUT a la toma
de entrada de 4 Ω de la caja acústica. Utilice un cable de altavoz para
efectuar esta conexión. Las cajas acústicas Ibanez de la serie IS, disponen de dos tomas de entrada. Utilice la que lleva la marca MONO 4Ω.
2) Conecte la guitarra eléctrica a 1 INPUT. Utilice un cable blindado
para efectuar las conexiones.
3) Si va a usar un procesador de efectos compacto, utilice un cable
blindado para conectarlo entre la guitarra y el amplificador.
4) Verifique que el volumen 10 MASTER se encuentre en 0 y encienda
el amplificador con el interruptor POWER 11. Aparece la animación de
encendido y el amplificador queda listo para funcionar.
Nota: Cuando haya terminado de utilizar el amplificador, verifique que el
volumen 10 MASTER se encuentre en 0 y luego apague el amplificador
con el interruptor POWER 11.
● Si va a utilizar el IFC2
Si conecta el IFC2 opcional (vendido por separado), podrá acceder a
los cinco efectos de pedal adicionales. Para más detalles acerca de las
conexiones, consulte el manual de instrucciones del IFC2.
68
2. Creación de sonidos
Vamos a empezar a crear algunos sonidos. En este ejemplo vamos a
utilizar el preajuste número 11, PSYCHO.
1) En la sección de memoria 3, pulse el interruptor MANUAL.
De este modo se selecciona la función manual, en la que todos
los ajustes de sonido reflejarán la posición real de los controles.
2) Suba el volumen 10 MASTER a una posición entre las 8 y las
12 horas.
3) Ajuste las secciones de preamplificación 2 del modo siguiente.
Nota: Este amplificador puede generar volúmenes extremadamente elevados. Sitúe el volumen 10 MASTER
de modo que no provoque molestias
a otras personas.
Con este ajuste se producirá un sonido con una distorsión muy ajustada. Ahora vamos a añadir algunos efectos.
4) Primero añadiremos el efecto 7 MODULATION. Efectúe los ajustes
siguientes.
FX TYPE&PARAMETER:FLANGER 15
FX MIX LEVEL :20
TAP TEMPO :10
*En la ilustración
anterior se muestra
el MIMX 150H.
5) Seguidamente añadiremos el efecto 8 DELAY&REVERB. Efectúe
los ajustes siguientes.
FX TYPE&PARAMETER:REVERB HL 10
FX MIX LEVEL :30
TAP TEMPO :1
*En la ilustración
anterior se muestra
el MIMX 150H.
Observará que el sonido se ha hecho más espacioso. Ahora intente
crear sus propios sonidos de la misma manera. A continuación aprenderá cómo memorizar un sonido que ha creado.
* Consulte "Acerca del
interruptor TAP" má s
adelante en este manual.
Nota: El interruptor TAP responde
a cualquier toque, por ligero que
sea. Si lo acciona con una fuerza
excesiva puede estropearlo; por
tanto, púlselo con suavidad.
3. Memorizar un sonido que ha creado
En esta sección aprenderá cómo se guarda un sonido que ha creado.
Vamos a guardar el nuevo sonido en el banco A, canal 1.
* Para más detalles acerca de la inicialización de la memoria, consulte
5. Reposición de los ajustes de fábrica
1) Verifique que la Pantalla 5 indique M. A continuación mantenga pulsado el interruptor con la marca "1" durante un mínimo de tres segundos. Cuando los ajustes estén guardados, la Pantalla 5 indicará A1 y
parpadeará.
Puede guardar en cualquier canal un sonido creado con la función manual como se describe aquí. Un sonido creado en cada banco se puede
guardar en un canal de ese banco.
Veamos un ejemplo.
2) Hasta aquí hemos utilizado el banco A, canal 1, para crear un sonido,
pero ahora vamos a ajustar ligeramente la posición de cada control y
guardar el resultado en el banco A, canal 2. Realice los pasos siguientes.
Nota: Cada canal está formado por dos bancos, A y B. Si desea
guardar ajustes en el banco A del canal 1 según se describe en esta
guía después de crear un sonido de modo manual, primero debe
pulsar "1," verificar que se encuentra actualmente en el banco A y
luego pulsar el interruptor MANUAL una vez más para volver a la
función manual antes de continuar con los pasos siguientes.
Mantenga pulsado durante un mínimo de tres segundos.
4. Uso de patrones de ritmo
En esta sección se explica cómo utilizar patrones de ritmo.
1) Empezaremos por tocar un ritmo. Pulse el interruptor ON/OFF. El interruptor TAP parpadea y se oyen sonidos de batería.
Nota: Utilice el mando RHYTHM para ajustar el volumen adecuadamente.
2) A continuación vamos a cambiar el patrón. Pulse + o - hasta que la
Pantalla 5 indique 16.
3) Hagamos el tempo un poco más rápido. Pulse el interruptor TAP varias veces a un ritmo uniforme hasta que la Pantalla 5 indique 120.
Toque un patrón
de ritmo
Cambie el patrón
del ritmo
Cambie la velocidad
del ritmo
Puede utilizar patrones de ritmo siguiendo el procedimiento descrito
anteriormente.
5. Reposición de los ajustes de fábrica
En esta sección se explica cómo reponer los ajustes de fábrica del
amplificador.
1) Mientras mantiene pulsado el interruptor MANUAL como se muestra
en la ilustración siguiente, encienda el amplificador con el interruptor
POWER 11. La Pantalla 5 indica AL.
2) Si en este momento pulsa el interruptor MANUAL, se restablecerán
todos los datos de fábrica.
3) Si decide cancelar la operación sin reponer los datos, accione cualquier control salvo el interruptor MANUAL. De este modo sale de la
función de reposición de los ajustes de fábrica.
ESPAÑOL
Edite el sonido del
banco A, canal 1
Mantenga pulsado durante
un mínimo de tres segundos
El sonido se guarda en
el banco A, canal 2
Al guardar el sonido editado en otro banco, podrá comparar ambos sonidos. A continuación vamos a intentar utilizar patrones de ritmo.
Mientras mantiene pulsado el interruptor MANUAL, encienda el
amplificador con el interruptor
POWER.
INPUT: Esta es una toma de entrada de tipo telefónico de 1/4 de pulgada.
1
Sección de preamplificación: Controla el tono de la guitarra. A continuación se detalla
2
cada función de preamplificación.
1) AMP SELECTION: Este mando permite seleccionar once tipos de preamplificación.
Para m ás detalles, consulte la sección en que se describen los diferentes amplificadores.
2) GAIN: Con este mando se ajusta la ganancia. El margen de ajuste depende de la
posición del mando AMP SELECTION. Según el nivel de ganancia, la Pantalla 5 indica-
ESPAÑOL
rá un valor entre 0 y 100.
3) Ecualizador: Estos son los controles de graves, medios y agudos (BASS, MIDDLE,
TREBLE) del ecualizador de tres bandas. El margen de ajuste y la función dependerán
de la posición del mando AMP SELECTION. Según el nivel, la Pantalla 5 indicará un
valor entre -15 y 15.
4) VOLUME: Con este mando se controla el nivel de salida del preamplificador. Según el
volumen, la Pantalla 5 indicará un valor entre 1 y 50. El nivel de salida se verá afectado
por el tipo de amplificador seleccionado, el nivel de ganancia y los niveles del ecualizador.
Puede utilizar este control para mantener un nivel consecuente entre los canales, así como
para especificar el nivel deseado. El volumen final se ajusta con el control de volumen
MASTER 10.
Sección de memoria: Para guardar un sonido que haya creado, mantenga pulsado durante
3
un mínimo de tres segundos el interruptor del canal en el que desee guardarlo. A continuación se describe el proceso con más detalle.
1) MANUAL: Con este interruptor se selecciona la función manual, en la que todos los ajustes
de sonido reflejarán la posición real de los controles. La Pantalla 5 indicará M.
2) Canales (1-5): Con estos interruptores se selecciona uno de los cinco canales en el que
desee guardar sus propios ajustes. Hay dos bancos de memoria (A y B), en los que podrá
guardar un total de diez sonidos. Como alternativa, en lugar de seleccionarlos en el panel
frontal, puede conectar el pedal opcional IFC2 (se vende por separado) y seleccionar con él
los canales. La Pantalla 5 indicará el número de canal (1-5).
3) Conmutador de los bancos A/B: Hay dos bancos, cada uno de los cuales contiene
cinco canales.
Sección de batería: Puede utilizar cincuenta patrones de ritmo diferentes.
4
*En la ilustración
anterior se muestra el
MIMX 150H.
70
1) Mando RHYTHM: Con este mando se controla el volumen de la
batería.
2) ON/OFF: Con este interruptor se activa/desactiva el patrón rítmico.
3) -/+: Con estos interruptores puede escoger uno de los cincuenta
patrones de ritmo diferentes. Para más detalles de cada patrón, consulte ESPECIFICACIONES.
4) Interruptor TAP: Con este interruptor se controla la velocidad del
ritmo, entre 40 PPM y 199 PPM.
Pantalla: En ella se muestran diferentes operaciones.
5
TUNER ON/OFF: El MIMX dispone de un afinador cromático. En las ilustraciones si-
6
guientes se muestra lo que indicará la pantalla cuando esté funcionando el afinador.
Encendido para indicar un
bemol
Movimiento
de la indicación
Cuando el tono
está bajo
Sección MODULATION: Aquí puede controlar cuatro tipos de efectos de modulación.
7
1) Mando FX: Con este mando se seleccionan cuatro tipos de efectos de modulación.
Estos efectos son los siguientes.
*En la ilustración anterior se muestra el
MIMX 150H.
2) Mando MIX: Controla el nivel de mezcla del efecto de modulación entre 0 y 100. En 0,
el efecto está desactivado y no se aplica ningún efecto de modulación.
3) Interruptor TAP: Controla la velocidad del efecto de modulación entre 1 y 50. En la tabla
siguiente se muestra la velocidad de modulación que se puede controlar con el interrup-
tor TAP en cada función.
Para más detalles acerca de la función TAP, consulte "Acerca del interruptor TAP".
Nota: Si utiliza el efecto PEDAL PITCH de la sección PEDAL FX 9 no podrá utilizar los
efectos de la sección MODULATION.
Cuando el tono es
correcto: MI bemol
a. CHORUS: Este efecto crea un sonido rico superponiendo el sonido y
modulándolo. Con el mando FX podrá variar la profundidad de modulación entre 0 y 100.
b. FLANGER: Este efecto aplica modulación y barrido al sonido. Con el
mando FX podrá variar la profundidad de modulación entre 0 y 100.
c. VIBRATO: Este efecto aplica un vibrato. Con el mando FX podrá variar
la profundidad de modulación entre 0 y 100.
d. STEP: Este efecto varía el sonido de forma escalonada. Con el mando FX podrá variar la profundidad de modulación entre 0 y 100.
Sección DELAY & REVERB: Aquí puede controlar cuatro efectos diferentes
de retardo y reverberación.
1) Mando FX: Con este mando se selecciona uno de los cuatro efectos de
retardo y reverberación. A continuación se enumeran estos efectos.
*En la ilustración se
muestra el MIMX 150H.
2) Mando MIX: Controla el nivel de mezcla del efecto de retardo y reverberación entre 0 y 100. En 0 el efecto está desactivado y no habrá ningún retardo
ni reverberación.
3) Interruptor TAP: Cuando se utilice DELAY o ECHO, con este interruptor se
controla el tiempo de retardo. Cuando se utiliza REVERB, con este interruptor se controla la longitud de la reverberación. En la tabla siguiente se muestra el tiempo de retardo y el tiempo de reverberación que se puede controlar
con el interruptor TAP en cada función.
Tiempo
Contenido de
la Pantalla
Para más detalles acerca de la función TAP, consulte "Acerca del interruptor TAP".
Nota: No se puede usar REVERB mientras se está utilizando la sección de
batería
4
Sección PEDAL FX: Puede controlar los efectos de pedal con un pedal opcional IFC2 (se vende por separado). Para más detalles, consulte "Más información acerca del pedal".
1) Interruptor SELECT: Con él se selecciona uno de los cinco tipos de efectos de pedal. Estos efectos son los siguientes.
a. DELAY: Este efecto añade una copia retardada del
sonido original, algo así como un "canon" musical. Utilice
el mando FX para variar la realimentación entre 0 y 40.
b. ECHO: Este efecto produce un retardo más cálido.
Utilice el mando FX para variar la realimentación entre 0
y 40.
c. REVERB HL: Esta reverberación simula la acústica de
un espacio amplio, como una sala de conciertos. Utilice
el mando FX para variar el carácter de la reverberación
entre 0 y 10.
d. REVERB RM: Esta reverberación simula la acústica
de un espacio pequeño, como una habitación. Utilice el
mando FX para variar el carácter de la reverberación entre
0 y 10.
a. VOL PEDAL: Es un pedal de volumen que le permite
controlar el volumen con el pie.
b. RING MOD: Este efecto aplica un carácter metálico al
sonido.
c. AUTO RESO: Este efecto varía la frecuencia de resonancia según la intensidad del punteo.
d. WAH WAH: Es un efecto wah-wah.
e. PEDAL PITCH: Este efecto le permite variar el tono en
tiempo real.
2) Mando de control: Con este mando se controla el efecto de la sección
PEDAL FX. Los efectos disponibles en cada función son los siguientes.
Posición mínimaPosición máxima
3) Toma para pedal: Puede utilizar el pedal conectando el IFC2 que se vende
por separado.
4) Toma para pedal: Puede utilizar la sección
IFC2 opcional (se vende por separado).
10
Volumen MASTER: Controla el nivel de salida final que se envía al altavoz.
11
Interruptor de alimentación POWER: Es el interruptor general del amplificador.
12
AC INPUT: Conecte aquí el cable de alimentación que se incluye.
13
LINE OUT (MIMX 150H): Se trata de una toma de salida de nivel de línea.
14
SPEAKER OUT (MIMX 150H): Se trata de una toma de salida para altavoz.
Utilice un cable de altavoces para conectar a esta toma un sistema de altavoces de 4 Ω o de 8 Ω.
Nota: Si utiliza un sistema de altavoces con una impedancia inferior a 4 Ω, (p.
ej. un sistema de 2 Ω), el amplificador se recalentará, se activará la protección de los circuitos y no se producirá la salida correcta.
15
HEADPHONES (MIMX65): Es una toma de salida para auriculares.
16
CD INPUT (MIMX65): Se trata de una toma de entrada de nivel de línea.
9
PEDAL FX conectando el
Puede conectar un reproductor de CD portátil o un MP3.
9
ESPAÑOL
71
Seleccion de programas de amplificacion
El dial AMP SELECTION le permite escoger once tipos de programas
de preamplificación. De los numerosos amplificadores de guitarra que
existen, Ibanez se ha centrado en los sonidos distintivos de diez
amplificadores clásicos particularmente apreciados por muchos guitarristas. Todo lo que hay entre la entrada de la guitarra y la salida del
altavoz se ha analizado y memorizado en forma de programa de
preamplificación. El MIMX está diseñado de forma que se puedan conseguir fácilmente sonidos similares a los de esos amplificadores. En la
ESPAÑOL
ecualización de cada programa se ha tenido en cuenta el sonido general muestreado del amplificador, incluida la respuesta cuando se asocian (o no) controles como los de presencia, brillo, resonancia o profundidad, de modo que con cada modelo se pueden obtener llamativas
imágenes de los tonos clásicos. No se trata en modo alguno de réplicas
exactas, sino más bien de un “sabor”, por así decirlo. Por último, cuenta
con un sonido original Ibanez contenido, duro y suave, en el programa
número 11. Su nombre, muy apropiado, es “Psycho.”
NOTA: En la descripción siguiente de los programas de preamplificación
los nombres de productos que no son Ibanez se utilizan como referencias tonales comprensibles y familiares para ilustrar la clase de sonidos
en los que se ha inspirado la programación de la preamplificación del
MIMX. Estas referencias y comparaciones con productos no Ibanez son
totalmente subjetivas. Ibanez no afirma en modo alguno que los programas de preamplificación del MIMX sean representaciones tonales exactas de los amplificadores objeto de referencia o comparación. Dicho
esto, creemos que le va a encantar lo que va a escuchar con esta amplia selección de tonos que puede conseguir con su nuevo MIMX.
60s Clean:
Este programa se ha creado para evocar el sonido de uno de los
amplificadores clásicos fabricados por Fender®, el ’65 Twin Reverb®,
tocado a través de su canal NORMAL con el BRILLO desactivado. Al
mencionar los sonidos limpios de los años sesenta todos recordamos
este amplificador. En el sonido de este programa destacan los agudos
cristalinos y los sólidos graves, reminiscencia de los sonidos clásicos
de la década de los sesenta, aunque no deja de tener un agradablemente singular sonido propio.
Jazz Combo:
Este programa se ha inspirado en el Roland® JC-120, famoso por su
capacidad para trasladar el tono ágil de la propia guitarra tocando a
través del CANAL 1 con el BRILLO desactivado y el tono general suavizado. La amplia gama dinámica de este programa y el sonido descolorido desde los graves hasta los agudos combina muy bien con los
procesadores de efectos y, por ello, este programa resulta muy versátil.
70s Brit:
Este sonido es una reminiscencia del clásico sonido del Marshall®
“JCM800 2203” combinado con la sobreexcitación que se obtiene cuando se utiliza el TUBESCREAMER®/TS-9 Ibanez® como refuerzo. Desde acordes sólidos hasta brillantes solos, este programa abarca un amplio
abanico de sonidos creativos.
Brit Blues:
La historia del VOX® “AC30” discurre paralela a una extensa franja de la
historia musical que incluye el blues, el rock y el pop. Puesto que su
fama permanece intacta a día de hoy y sigue teniendo numerosos admiradores entre los profesionales de la música, crear un programa de
preamplificación influido por este tipo de sonido era una decisión obvia.
Al crear el sabor MIMX hemos añadido ganancia con unos medios y
una tensión distintivamente claros a fin de potenciar el tono clásico. Los
matices del punteo se transmitirán con total fidelidad y podrá tocar con
una amplia variedad de tonos.
72
US Blues:
Opinamos que este programa recuerda mucho al Fender® “Hot Rod
Deville™” tocado a través del canal EXCITADO con el BRILLO en posición NORMAL y la SOBREEXCITACIÓN activada. El MIMX ha potenciado los graves de ese sonido y ha dado a la ecualización un estilo
escalonado. El atractivo particular de este programa es un sonido brillante con una resonancia distintivamente dura. Desde un sonido con
menos ganancia que resalta el carácter tonal duro hasta la excitación
con un sonido excelente que se obtiene elevando la ganancia, este programa ofrece una amplia paleta de tonos.
Rock:
Este programa es nuestra interpretación del sonido del “Ecstasy 101B
EL34 Version”, un amplificador de válvulas polivalente fabricado por
Bogner Corporation, famosa por sus amplificadores de boutique. La respuesta a los ajustes da una gama dinámica incrementada desde la ganancia baja hasta la ganancia alta, con más nivel de control de
ecualización. Notable por su tono recortado, este programa le proporciona una amplia variedad de sonidos, desde acordes dulces y limpios
hasta acordes duros, así como sonidos sobreexcitados sostenidos.
Hard Rock:
En un principio el Soldano’s® “SL0-100” sólo se vendió a pocos músi-
cos como amplificador personalizado hasta que, finalmente, alcanzó un
gran éxito y renombre. Hemos creado este programa para obtener un
sonido similar al del canal SOBREEXCITADO del SLO-100 con el BRILLO en posición NORMAL pero reduciendo la posibilidad de acoplamiento con una tensión y contención generales. Creemos que el sonido
de alta ganancia está particularmente conseguido y resulta ideal para
solos o riffs heavy.
Guitar God:
Esta es nuestra idea de cómo suena el Peavey® “5150 II®”. Para crear
este programa en el MIMX, hemos escuchado tanto el amplificador
Peavey real como las Fuentes de sonido utilizadas en un CD a fin de
reproducir los sonidos que, para nosotros, son la reminiscencia de aquellos sonidos grabados. Los graves contenidos son adecuados para los
riffs que entremezclan silencios y, con la distorsión, conseguirá unos
solos con sostenidos memorables.
90s Brit:
Este programa se ha diseñado también con referencias tanto al amplifi-
cador, en este caso el Marshall® “JCM2000 DSL100”, como a las fuen-
tes reales de audio grabadas en CD de un grupo que utilizaba este
amplificador. Nuestro enfoque con este sonido produce un componente
de distorsión rudo, pero el sonido es contenido y bien definido con una
buena separación de las notas, por lo que se puede utilizar en toda
clase de elementos, desde arpegios cristalinos hasta riffs ostentosos.
Le garantizamos que el sonido de su guitarra destacará, incluso en un
grupo con sonido potente.
LA Heavy:
El Mesa/Boogie® “Dual Rectifier® Solo Head” ha influido a numerosos
músicos de estilo heavy. Este programa es nuestra interpretación de un
collage de los sonidos clásicos de un modelo presentado en 1989 que
ha definido el tono de la guitarra heavy moderna. Nuestra versión aporta el sonido distorsionado de las válvulas originales 6L6 a través del
canal RED con la fuente de alimentación en BOLD, utilizando la función
de rectificador de diodos-silicio finalmente tocada a través de una caja
cuatro-doce Ibanez® Thermion® TN412A. El resultado son unos graves
impresionantes con un buen crujido.
Psycho:
Este es un sonido original de Ibanez, diseñado para captar la onda de la
escena del rock heavy actual. Los graves son contenidos y afilados, con
una nitidez soberbia. Con los ajustes de ecualización podrá utilizar este
sonido en cualquier estilo de música.
* A excepción de Ibanez®, TUBESCREAMER® y Thermion®, los
nombres de empresas y de productos que figuran en este manual
son marcas comerciales o marcas registradas de sus respectivos
titulares y carecen de afiliación alguna con Ibanez.
Fender®, Twin Reverb®, Hot Rod Deville™ son marcas registradas
o marcas comerciales de Fender Musical Instruments Corporation.
Roland® es una marca registrada de Roland Corporation.
Marshall® es una marca registrada de Marshall Amplification
Corporation PLC.
VOX® es una marca registrada de VOX R&D limited.
Soldano® es una marca registrada de Soldano Custom Amplification.
Peavey® es una marca registrada de Peavey Electronics LTD.
5150 II® es una marca registrada de E.L.V.H., Inc.
Mesa/Boogie® y Dual Rectifier® son marcas registradas de Mesa/
Boogie, Limited.
73
ESPAÑOL
Preajustes de fábrica
Son los ajustes de sonido asignados a cada canal A1-B5 cuando el
MIMX sale de fábrica. Basta pulsar un botón para obtener las combinaciones distintivas de sonido y efectos del MIMX.
A1: Immortal Shred
SELECCIÓN DE AMPLIFICACIÓN: Psycho
Este preajuste es ideal para los riffs rápidos típicos de los grupos de
slash metal o death metal de la escena musical actual. Los medios se
recortan para resaltar los agudos y los graves y se crea un sonido ro-
ESPAÑOL
busto elevando los graves sin reducir excesivamente los medios.
A2: Shrapnel Heroes
SELECCIÓN DE AMPLIFICACIÓN: Psycho
Este preajuste se puede utilizar para solos de guitarra en una gran variedad de tipos de música, desde hard rock hasta heavy metal. La
ecualización es relativamente plana. Si añade un retardo bastante rápi-
do, este preajuste le proporcionará un buen sonido para hacer solos.
A3: Cruel Heaviness
SELECCIÓN DE AMPLIFICACIÓN: 90s Brit
Este preajuste es para riffs en los que se destaca el ritmo. Resulta ideal
para temas de tempo bajo y los graves reforzados le proporcionarán un
sonido fuertemente distorsionado que empujará al sonido del conjunto.
Resulta ideal para los sonidos fuertes del rock actual.
A4: Legend of the Beast
ESTILO DE AMPLIFICACIÓN: Hard Rock
Este es un preajuste para guitarra solista con ese sonido Metal de los
ochenta. Este preajuste posee un carácter sonoro que recuerda a la
edad de oro del Metal típico de numerosos grupos metal británicos y de
LA.
A5: Emotional Clean
ESTILO DE AMPLIFICACIÓN: 60s Clean
Este preajuste proporciona unos graves gruesos, un ataque seco y reverberación para crear un ambiente cálido. Si utiliza una pastilla de una
sola bobina puede producir un sonido añejo brillante. Reduciendo el
nivel de mezcla del efecto de reverberación podrá reforzar la sensación
del ataque.
B1: Sounds of the Right Hand
SELECCIÓN DE AMPLIFICACIÓN: Guitar God
Este preajuste es ideal no solo para riffs potentes y veloces, sino también para solos. La distorsión que se obtiene elevando la ganancia al
máximo y unos medios penetrantes combinan bien con las pastillas de
doble bobina. Se aplica un ligero retardo dependiente del tiempo (flanger)
para producir una sensación de potencia, así como un retardo para crear
un efecto espacial.
B2: Purple Tone
SELECCIÓN DE AMPLIFICACIÓN: Rock
Este es un ajuste de alta ganancia que reduce fuertemente los graves y
añade un carácter distintivo a los medios. Con una pastilla de una sola
bobina puede obtener el sonido de mediados de los setenta. A medida
que suba los medios, el sonido adquirirá una atmósfera clásica para
ajustarla a su gusto. Para aprovechar al máximo este sonido, toque los
riffs de rock duro que revolucionaron la época y se han convertido en el
origen del rock duro actual.
B3: Crystal Clean
SELECCIÓN DE AMPLIFICACIÓN: Jazz Combo
Este preajuste se ha pensado para producir unos sonidos limpios y chispeantes como el cristal. Resulta adecuado para las "Power Ballads" de
rock duro y heavy metal de los ochenta y los noventa. Intente tocarlo
con pastillas de una bobina, ya sea la pastilla central o una combinación
de las pastillas central/mástil. Eleve el nivel de mezcla del efecto para
obtener un sonido más suntuoso.
B4: Solo DNA
SELECCIÓN DE AMPLIFICACIÓN: Rock
Este preajuste se ha creado para tocar esos solos picados que hicieron
famosos a los dioses de la guitarra de los ochenta. Es un ajuste magní-
fico para dar rienda suelta a su sentido musical. Utilice libremente la
flexión de cuerdas, el picado de trémolo, los armónicos y los arpegios y
exprese su imaginación.
B5: Samurai Edge
SELECCIÓN DE AMPLIFICACIÓN: 70s Brit
Este preajuste es una buena opción para acompañamientos o riffs de
estilo blues tocados con pastilla de una bobina. Proporciona el grado
justo de distorsión para acentuar los matices del punteo y produce unos
agudos muy claros. Ajuste la reverberación a su gusto.
74
Utilización del interruptor TAP con éxito
El MIMX dispone de un interruptor TAP con el que se puede controlar la
velocidad de los efectos y el ritmo. Puede que al principio le cueste
familiarizarse con él, pero pronto podrá utilizarlo de forma fácil e intuitiva.
Pulsando (apretando) este interruptor varias veces (no solo dos veces),
puede especificar la velocidad deseada. Mientras sigue pulsando, el
intervalo promedio se visualizará en la Pantalla 5.
Los interesados en los "tecnicismos" encontrarán a continuación una
explicación detallada de cómo la función TAP detecta el tempo medio.
Un promedio de movimiento
Para determinar el tempo a través de la velocidad del interruptor TAP se
utiliza un método denominado "promedio de movimiento". Por ejemplo,
si desea ajustar el tempo de la batería a 120 PPM, resulta muy difícil
especificar el tempo exacto simplemente pulsando el interruptor TAP
solo dos veces.
Promedio de movimiento de cuatro valores (utilizaremos cuatro valores para la
explicación)
Se utiliza el valor medio de los cuatro accionamientos más recientes del interruptor
TAP. Esto permite absorber las imprecisiones del accionamiento.
Valor
1125bpm2115bpm3130bpm4109bpm
accionado
Valor
producido
1
125bpm120bpm121bpm119bpm123bpm
(1+2)
2
Promedio de movimiento de dos valores
Tendrá que pulsar el interruptor TAP a un ritmo preciso de
modo que el intervalo entre la primera y la segunda pulsación
sea de 60/120 segundos = 0,5 segundos.
(1+2+3)3(1+2+3+4)4(2+3+4+5)
El MIMX utiliza un promedio de movimiento de siete valores. Al marcar
el compás con el interruptor TAP puede obtener un ajuste del tempo
más preciso.
5131bpm
4
La indicación "actualmente editada" de la pantalla central
El MIMX dispone de un LED de indicación "actualmente editada" que se
ilumina como se muestra en la ilustración siguiente.
LED "actualmente
editado"
Posición
del mando
Posición
del sonido real
un mando a una posición diferente a la del valor memorizado, el LED
"actualmente editado" en la parte inferior derecha de la Pantalla 5 se
ilumina para indicar esa circunstancia. Cuando mueve el mando a la
posición que corresponde al valor memorizado, la indicación
"actualmente editado" desaparece. Este es el valor que está guardado
en el canal seleccionado.
Veamos un ejemplo.
1) Pulse A1.
2) Mueva el mando GAIN a la posición de las 12
horas. La Pantalla 5 indica 50 y el punto se
ilumina. Esto indica que se ha editado la ganancia
y que es diferente a la ganancia memorizada.
3) Mueva el mando GAIN a la posición máxima.
La Pantalla 5 indica 100 y el punto se apaga.
Esto indica que la ganancia memorizada es la que
se muestra en la Pantalla 5.
* Esta función se aplica a todos los controles. Puede utilizarla para
comparar los valores memorizados con el valor actual o para comprobar
el contenido memorizado en cada canal.
* Si pulsa el interruptor MANUAL para seleccionar la función manual, la
posición de cada control corresponderá al valor real que determina el sonido.
El MIMX dispone de mandos
giratorios de tipo analógico para
facilitar la utilización. Sin embargo,
cuando pulsa el interruptor de un canal A1-B5 para seleccionar los
ajustes memorizados, los ajustes de
sonido recuperados por medio de los
mandos del panel frontal no se
corresponderán necesariamente con
la posición física de los mandos. Por
este motivo, cuando pulsa el
interruptor de un canal para recuperar
un ajuste memorizado y luego mueve
75
ESPAÑOL
Más información acerca de pedal
Puede utilizar el pedal IFC2 (vendido por separado) para controlar el
MIMX. Si conecta el IFC2 podrá utilizar la sección 9 PEDAL FX y los
interruptores del pedal para cambiar canales.
ESPAÑOL
a
e
d
b
f
c
A
B
Operaciones
a
Pedal: Controla el efecto de pedal seleccionado en el amplificador.
Interruptor Arriba: Cambia a la memoria inmediatamente superior
b
a la seleccionada actualmente. (No funciona de modo manual).
c
Interruptor Abajo: Cambia a la memoria inmediatamente inferior a
la seleccionada actualmente. (No funciona de modo manual.)
d
Toma para pedal-interruptor: Conecte esta toma al amplificador para
utilizar el pedal como interruptor.
e
Toma de pedal-efectos: Conecte esta toma al amplificador para
utilizar el pedal para efectos. Un circuito interno del IFC2 permite al
MIMX reconocer que el pedal está conectado.
Conmutador de función: Este interruptor determina cómo funcio-
f
nará el pedal. Sitúelo como corresponda a su estilo de tocar.
A
El efecto permanecerá activado aunque el pedal se encuentre en
la posición mínima (completamente hacia usted).
B
El efecto se desactivará cuando el pedal se sitúe en la posición
mínima (completamente hacia usted).
Pulse b c simultáneamente para activar el afinador.
76
Localización de problemas
En primer lugar compruebe que el cable blindado de la guitarra, el cable del
altavoz y el cable de alimentación estén conectados correctamente. Si es posible,
compruebe el cable con un comprobador o utilice un cable o amplificador
alternativos para verificar el estado del cable.
1. No se puede conectar la alimentación.
• Compruebe que el cable de alimentación esté correctamente enchufado.
• Intente enchufarlo a una toma de corriente diferente y observe si persiste el
problema.
2. Se puede conectar la alimentación, pero no se obtiene
sonido.
• Compruebe que la guitarra esté conectada correctamente.
• Elimine todos los componentes externos conectados al bucle de efectos y en-
tre la guitarra y el amplificador y compruebe si se obtiene algún sonido.
• Utilice un cable blindado diferente y compruebe si se obtiene sonido.
• Compruebe si el volumen de la guitarra está en “0”.
• Utilice una guitarra diferente y compruebe si se obtiene algún sonido.
• Compruebe si el volumen del amplificador está en “0”.
• Compruebe si están conectados los auriculares.
•¿Sigue sin haber sonido cuando sube el volumen general?
• Compruebe si está utilizando el pedal IFC2 que se vende aparte para controlar
el volumen y si dicho pedal se encuentra en posición completamente girada
(hacia usted).
3. Se oye ruido.
• Compruebe si hay algo cerca que esté resonando o golpeando contra el
amplificador y produzca el ruido.
• Compruebe si la cubierta del enchufe del cable blindado está floja.
• Asegúrese de que la altura de las cuerdas esté ajustada correctamente.
• Utilice otra guitarra, efectos o componentes externos y compruebe si se pro-
duce el mismo ruido.
4. No se oye sonido cuando se conecta un reproductor de
CD.
• Asegúrese de que el volumen del reproductor de CD no esté ajustado al mínimo.
• Asegúrese de que el cable esté conectado correctamente.
• Intente utilizar otro cable para ver si hay sonido.
5. El CD no suena bien.
¿El cable que está utilizando tiene una clavija estereofónica? ¿Es posible que esté
utilizando una clavija monoaural?
6. No se produce sonido en los auriculares
• Compruebe que los auriculares estén correctamente conectados.
• Conecte otros auriculares y compruebe si se produce sonido.
7. No suena la batería.
• Compruebe si el volumen de la batería está en 0.
• Compruebe si el volumen general está en 0.
• Compruebe si están conectados los auriculares.
8. No se aplica el efecto de modulación.
• Compruebe si el volumen de mezcla está en 0.
• Compruebe si está utilizando el afinador que va incorporado en el MIMX.
• Compruebe si está utilizando el pedal de control IFC2 que se vende aparte
para controlar el tono (PITCH).
9. No se aplica el efecto de retardo.
• Compruebe si el volumen de mezcla está en 0.
•¿Se produce algún cambio cuando acciona el pulsador?
• Compruebe si está utilizando el afinador que va incorporado en el MIMX.
10. No se aplica el efecto de reverberación.
• Compruebe si el volumen de mezcla está en 0.
• Compruebe si se produce algún cambio cuando acciona el pulsador.
• Compruebe si está utilizando la función DRUM (batería).
• Compruebe si está utilizando el afinador que va incorporado en el MIMX.
11. No puedo usar el efecto de pedal.
•¿Está conectado el pedal de control IFC2 que se vende aparte?
•¿Está utilizando el cable que se incluye con el IFC2?
• Compruebe si está utilizando el afinador que va incorporado en el MIMX.
En caso de defectos
Este producto ha sido revisado exhaustivamente antes de salir de fábrica. Cuando
piense que existe un problema, realice los procedimientos indicados más arriba.
En el caso improbable de que se produjera alguna anomalía durante la utilización,
póngase en contacto con su distribuidor. Además, cuando solicite reparaciones,
explique con detalle los síntomas del problema para facilitar su rápida resolución.
Debido a las mejoras de este producto, las especificaciones pueden cambiar
sin previo aviso.
ESPAÑOL
77
Introduzione
Grazie per aver acquistato questo amplificatore per chitarra Ibanez della serie
MIMX. Gli amplificatori ad elaborazione digitale (digital modeling) della serie
MIMX offrono un audio di altissima qualità grazie al trattamento del segnale a
32 bit. Leggere attentamente questo manuale prima di usare l'amplificatore in
modo da sfruttarne appieno le caratteristiche e le funzioni disponibili. Conservare
quindi il manuale in un luogo sicuro.
Precauzioni durante l'uso
1) Leggere le avvertenze contenute in questo manuale di istruzioni.
ITALIANO
2) Tenere le avvertenze contenute in questo manuale a portata di mano per
consultarle all'occorrenza.
3) Osservare tutte le avvertenze.
4) Seguire le istruzioni contenute in questo manuale di istruzioni.
5) Usare solo un panno asciutto per pulire l'amplificatore.
6) Questo prodotto è in grado di produrre suoni a livelli di volume molto alti. In
alcuni casi, ciò potrebbe danneggiare l'udito o causare altre lesioni. Prestare
quindi attenzione al volume quando si utilizza il prodotto.
7) Assicurarsi che sia sempre collegato un sistema di altoparlanti dell'impedenza
corretta.
8) Usare questo prodotto con un'alimentazione avente una tensione pari ai valori
stampati sul pannello posteriore.
9) Non schiacciare o calpestare il cavo di alimentazione, specialmente vicino allo
spinotto o alla presa.
10)Posizionare questo prodotto vicino alla presa dell'alimentazione di rete e
assicurarsi che, in caso di problemi, la spina del cavo di alimentazione possa
essere facilmente scollegata dalla presa di corrente.
11) Usare solo i componenti in dotazione o gli optional che rispettano le specifiche
del produttore.
12) Questo apparecchio contiene un fusibile di protezione. Il fusibile può rompersi
per urto fisico esterno o perché ha raggiunto la fine della sua vita utile; dato
però che un fusibile rotto può indicare un grave guasto interno, contattare il
proprio rivenditore prima di sostituirlo.
13) Far effettuare tutti gli interventi d'assistenza dal personale tecnico autorizzato
dal distributore. Interventi d'ispezione o assistenza sono necessari se il cavo di
alimentazione o la spina sono danneggiati, se fuoriesce del liquido dall'unità, se
un oggetto esterno entra nell'unità, se l'unità si bagna con la pioggia o altri
liquidi, se l'unità viene fatta accidentalmente cadere o se l'unità non funziona
normalmente.
14) Quando non lo si utilizza, spegnere l'interruttore power. Quando l'MIMX è
collegato ad una presa elettrica, non è completamente isolato dall'alimentazione
anche se l'interruttore power è spento. Se non si utilizza l'MIMX per un lungo
periodo, lasciare il cavo di alimentazione scollegato.
15) Non spegnere l'alimentazione o scollegare la spina dalla presa CA durante il
funzionamento dell'apparecchio, perché questo potrebbe provocare guasti.
16) Non salire sull'apparecchio o collocare oggetti pesanti sopra di esso per evitare
di romperlo o provocare guasti.
78
Avvertenze sulla collocazione dell'apparecchio
17) Qualora s'intenda usare il MIMX collocandolo su un rack per altoparlante, è
necessario installare quest'ultimo saldamente a pavimento oppure a parete. In
particolare, qualora s'intenda usarlo collocandolo su un rack con due altoparlanti
(ad esempio un rack completo), quest'ultimo deve essere collocato su una
superficie piatta e orizzontale oppure a parete e quindi bloccato con cinture di
sicurezza o dispositivi analoghi affinché non possa cadere.
18) Non porre questo apparecchio in luoghi soggetti a temperature particolarmente
basse, quali celle frigorifere. L'apparecchio potrebbe non funzionare
correttamente
19) Non porre questo apparecchio in luoghi soggetti a forti campi magnetici, ad
esempio vicino a un televisore o una radio, o vicino ad altri apparecchi che
emettono radiazioni elettromagnetiche. L'apparecchio potrebbe non funzionare
correttamente in queste condizioni.
20) Non porre l'apparecchio in luoghi soggetti a cambi di temperatura repentini
Se l'apparecchio si trova in una stanza fredda la cui temperatura aumenta
improvvisamente, all'interno dell'apparecchio può formarsi della condensa che
può impedire un funzionamento corretto.
21) Non porre l'apparecchio in luoghi con polvere o soggetti a vibrazioni eccessive
Queste condizioni possono provocare danni o impedire un funzionamento
corretto.
22) A seconda del luogo in cui si pone l'apparecchio, si potrebbero verificare
interferenze in apparecchi radio collocati nelle vicinanze oppure sfarfallii o
distorsioni sullo schermo di una televisione vicina. Se si sospetta che sia questo
apparecchio la causa di tali disturbi, spegnere l'alimentazione dell'apparecchio.
Se, dopo lo spegnimento, la radio o la televisione tornano a funzionare
normalmente, cercare di allontanarle dall'apparecchio o di modificarne
l'orientamento.
ITALIANO
79
Precauzioni di sicurezza
Leggere attentamente e seguire scrupolosamente queste precauzioni prima di
usare l'apparecchio.
Dopo averle lette, conservarle insieme al "Manuale di istruzioni" e alla "Garanzia".
Prevenzione di incendi, elettrolocuzioni o lesioni
Note sui simboli grafici
indica che occorre prestare attenzione (anche un pericolo o
ITALIANO
un'avvertenza). Il contenuto specifico dell'avvertenza è indicato
all'interno del triangolo. Il simbolo mostrato sulla sinistra indica di
prestare attenzione in generale, un'avvertenza o un pericolo.
indica un divieto (qualcosa che non bisogna fare).
L'oggetto specifico del divieto è raffigurato all'interno del
simbolo. Il simbolo mostrato sulla sinistra indica che non
bisogna smontare l'unità.
indica un'azione obbligatoria (qualcosa che bisogna fare).
L'obbligo specifico è raffigurato all'interno del simbolo.
Avvertenze
Se dall'apparecchio fuoriesce fumo
C'è pericolo di incendio o di scosse elettriche se si continua a usare
l'apparecchio quando avvengono anormalità quali la fuoriuscita di fumo o
di odori insoliti. Spegnere immediatamente l'alimentazione, scollegare la
spina dalla presa CA e contattare il rivenditore da cui si è acquistato
l'apparecchio. Non cercare mai di riparare l'apparecchio da soli, può essere
pericoloso.
Se l'apparecchio si rompe
Se l'apparecchio cade o se il cabinet è danneggiato, spegnere
immediatamente l'alimentazione, scollegare la spina dalla presa CA e
contattare il rivenditore da cui si è acquistato l'apparecchio. C'è pericolo
di incendio o di scosse elettriche se si continua a usare l'apparecchio in
queste condizioni.
Se un corpo estraneo entra nell'apparecchio
Se un corpo estraneo metallico o infiammabile dovesse entrare all'interno
di questo apparecchio attraverso un jack o un'altra apertura, spegnere
immediatamente l'alimentazione, scollegare la spina dalla presa CA e
contattare il rivenditore da cui si è acquistato l'apparecchio. C'è pericolo
di incendio o di scosse elettriche se si continua a usare l'apparecchio in
queste condizioni.
Non smontare o apportare modifiche
all'apparecchio
Non aprire il cabinet di questo apparecchio. Questo apparecchio contiene
componenti ad alta tensione; se li si tocca può prodursi una scossa
elettrica. Contattare il proprio rivenditore se è necessario effettuare
un'ispezione dell'interno o prestare assistenza all'apparecchio.
Non apportare modifiche all'apparecchio per non causare incendi, scosse
elettriche o guasti.
Non porre acqua o agenti chimici sull'apparecchio
Per evitare il rischio di incendio o di scosse elettriche, non porre vasi di
fiori, bevande, cosmetici o contenitori di agenti chimici o di acqua
sull'apparecchio.
Scollegare dalla presa CA in caso di temporali
Se vi sono fulmini nelle vicinanze, spegnere l'alimentazione, scollegare
la spina dalla presa CA e non usare più l'apparecchio. I fulmini possono
causare incendi o scosse elettriche.
Non avvicinare l'apparecchio a fiamme o a fonti di
calore
Non avvicinare l'apparecchio o il cavo di alimentazione all'impianto di
riscaldamento per evitare che il cabinet o la guaina del cavo di
alimentazione possano sciogliersi, provocando incendi o scosse elettriche.
Non usare lo strumento ad alti livelli di volume per
lungo tempo
L’uso dello strumento ad alti livelli di volume con cuffie o altoparlanti per
lungo tempo può provocare una perdita permanente dell’udito a seconda
delle impostazioni di riproduzione del volume.
80
Non porre l'apparecchio in luoghi molto umidi
Non usare l'apparecchio in luoghi molto umidi, come vicino a una vasca
da bagno o a un umidificatore, sotto la pioggia o vicino all'acqua, per
evitare incendi o scosse elettriche.
Non bloccare le ventole di raffreddamento
La parte posteriore dell'apparecchio funziona da ventola di raffreddamento,
lasciare quindi uno spazio sufficiente tra l'apparecchio stesso e la parete.
Se si blocca la ventola di raffreddamento, il calore rimarrebbe intrappolato
nell'apparecchio e potrebbe innescare un incendio.
Non porre l'apparecchio in luoghi soggetti ad alte
temperature
Non porre l'apparecchio in luoghi soggetti ad alte temperature, come alla
luce diretta del sole o vicino ad apparecchi che producono calore, quali
una stufa o un radiatore. In caso contrario, la temperatura interna crescerà
con il conseguente rischio di incendio.
Non esporre l'apparecchio a spruzzi di olio o al
vapore
Non porre l'apparecchio dove potrebbe essere esposto a spruzzi d'olio o
al vapore per evitare incendi o scosse elettriche.
Usare l'apparecchio solo con una presa CA della
tensione corretta
L'apparecchio deve essere utilizzato solo con una presa di alimentazione
CA della tensione corretta, indicata sull'apparecchio stesso. Se si usa
l'apparecchio con una presa CA della tensione errata, vi è il rischio di
incendio o di scosse elettriche.
Non utilizzare l'apparecchio con le mani bagnate
Non collegare o scollegare il cavo di alimentazione con le mani bagnate
per evitare rischi di scosse elettriche.
Maneggiare la spina con cautela
Quando si scollega il cavo dalla presa di corrente, assicurarsi di tirare
impugnando la spina. Se lo si scollega tirando il cavo stesso, si rischia di
danneggiarlo e di provocare quindi un incendio o scosse elettriche.
Non effettuare connessioni multiple
Non usare prolunghe multiple, ciabatte o spine multiple per collegare
diversi apparecchi ad una stessa presa di alimentazione CA per evitare il
rischio di incendio o di scosse elettriche.
Maneggiare il cavo di alimentazione con cautela
Non graffiare, danneggiare, modificare, piegare, tirare, torcere o avvolgere
in modo eccessivo il cavo di alimentazione. Se sul cavo di alimentazione
si pongono oggetti pesanti o se il cavo è esposto a calore, questo può
essere danneggiato e può esservi il rischio di incendio o di scosse
elettriche. Contattare il proprio rivenditore se il cavo di alimentazione è
danneggiato.
Usare l'apparecchio solo nel paese in cui lo si è
acquistato
Questo apparecchio è progettato per la tensione di alimentazione CA del
paese in cui è stato acquistato; non può quindi essere usato al di fuori di
tale paese.
Attenzione
Scollegare il cavo di alimentazione nel caso di
inutilizzo prolungato
Se non si utilizza l'apparecchio per un lungo periodo di tempo, per
sicurezza scollegare la spina dalla presa CA.
Non far cadere l'apparecchio e non sottoporlo a urti
Non fare cadere l'apparecchio e non sottoporlo a forti urti per non romperlo
o provocare guasti.
Non porre l'apparecchio in un luogo instabile
Non porre l'apparecchio in un luogo instabile, come un supporto traballante
o inclinato. L'apparecchio potrebbe divenire instabile e ribaltarsi o cadere,
provocando danni o lesioni.
ITALIANO
81
Guida
Questa sezione fornisce una spiegazione passo-passo di come effettuare le connessioni all'amplificatore, creare suoni, salvare o reimpostare
i suoni creati, e usare i pattern ritmici. Una volta seguite queste spiegazioni, comprenderete quasi tutte le operazioni dell'MIMX.
Le illustrazioni che appaiono qui sono prese dal pannello di controllo
dell'MIMX 150H.
1. Connessioni
ITALIANO
1)-a Leggere attentamente le avvertenze per l'uso e quindi impostare
l'amplificatore. Usare il cavo di alimentazione in dotazione per collegare
il pannello posteriore 12 AC INPUT ad una presa di corrente CA.
Nota: Il suono dell'amplificatore (in particolare la risposta delle frequenze basse) cambierà in funzione della posizione e dei parametri con i
quali si imposterà l'amplificatore.
1)-b Se si utilizza l'MIMX 150H, collegare 14 SPEAKER OUT al jack di
ingresso a 4Ω del cabinet dell'altoparlante. Usare un cavo per diffusori
per effettuare questo collegamento. Sui cabinet degli altoparlanti della
serie IS Ibanez, vi sono due jack di ingresso.Usare quello contrassegnato MONO 4Ω.
2) Collegare la chitarra elettrica a 1 INPUT. Usare un cavo schermato
per effettuare le connessioni.
3) Se si utilizza un dispositivo di effetti, usare un cavo schermato per
collegarlo tra chitarra e amplificatore.
4) Assicurarsi che il volume 10 MASTER sia impostato su 0, e accendere lo switch 11 POWER. Appare l'animazione di avvio e l'amplificatore è
pronto all'uso.
Nota: Quando si finisce di utilizzare l'amplificatore, assicurarsi che il volume 10 MASTER sia impostato su 0 e quindi spegnere lo switch
POWER.
● Se si usa l'IFC2
Collegando l'IFC2 opzionale (venduto separatamente), si può accedere
ai cinque effetti a pedale addizionali. Per dettagli sulle connessioni, consultare il manuale operativo IFC2.
2. Creazione del suono
Come iniziare a creare alcuni suoni. In questo esempio, si utilizzerà il
modello numero 11 detto PSYCHO.
1) Nella sezione di memoria 3, premere sullo switch MANUAL.
Seleziona la modalità manuale, in cui tutte le impostazioni audio
corrispondono alla posizione effettiva dei controlli.
2)
Alzare il volume 10 MASTER in una posizione tra ore 8 e ore 12.
3) Impostare la sezione preamplificatore 2 nel modo seguente.
Nota: Questo amplificatore è in
grado di produrre livelli di volume estremamente alti. Impostare il volume
che non crei inconvenienti a persone vicine.
Ciò produrrà un suono distorto molto compatto. Ora è possibile aggiungere alcuni effetti.
4) Come aggiungere l'effetto 7 MODULATION. Effettuare le impostazioni
seguenti.
FX TYPE&PARAMETER:FLANGER 15
FX MIX LEVEL :20
TAP TEMPO :10
*L'illustrazione
precedente mostra
l'MIMX 150H.
5) In seguito, aggiungeremo l'effetto 8 DELAY&REVERB. Effettuare le
seguenti impostazioni.
FX TYPE&PARAMETER:REVERB HL 10
11
*L'illustrazione
precedente mostra
l'MIMX 150H.
FX MIX LEVEL :30
TAP TEMPO :1
Nota: Lo switch TAP risponderà
anche a un tocco leggero. Se lo si
aziona con forza eccessiva lo si
può danneggiare. Quindi, premerlo leggermente.
Noterete che il suono è divenuto più spazioso. Ora sarà possibile procedere a creare i vostri suoni nello stesso modo. La prossima sezione
illustrerà come salvare i suoni che si sono creati.
10
MASTER in modo
* Consultare la sezione "Informazioni sullo switch TAP"
contenuta in seguito in questo manuale.
82
3. Salvare un suono creato
Questa sezione illustra come salvare i suoni che si sono creati. Il nuovo
suono verrà salvato nel banco di memoria A, canale 1.
* Per dettagli sull'inizializzazione della memoria, leggere 5.
Reimpostazione alla configurazione di fabbrica
1) Assicurarsi che il Display 5 indichi M. Quindi, tenere premuto lo switch
contrassegnato "1" per tre secondi o più. Quando le impostazioni sono
state salvate, il Display 5 indicherà A1 e lampeggerà.
Nota: Ogni canale è dotato di due banchi di memoria, A e B. Se, come
descritto in questa guida, si vogliono salvare le impostazioni nel banco
A, canale 1 dopo avere creato il suono in modalità manuale, premere
innanzitutto "1", assicurarsi di essere attualmente nel banco A e quindi
premere lo switch MANUAL ancora una volta per tornare alla modalità
manuale prima di procedure con le fasi seguenti.
4. Uso dei pattern ritmici
Questa sezione spiega come usare i pattern ritmici.
1) Come riprodurre un ritmo. Premere lo switch ON/OFF. Lo switch TAP
lampeggerà e si sentiranno i suoni della batteria.
Nota: Usare la manopola RHYTHM (ritmo) per regolare il volume in modo
appropriato.
2) Quindi, si procederà a cambiare il pattern. Premere + o - finché il
Display 5 indica 16.
3) Come rendere il tempo più rapido. Premere lo switch TAP diverse
volte a un ritmo costante finché il Display 5 indica 120.
ITALIANO
Tenere premuto per tre secondi o più.
Un suono creato in modalità manuale come qui descritto può essere
salvato in qualunque canale. Un suono creato in uno dei due banchi può
essere salvato in un canale all'interno di quel determinato banco.
Ecco un esempio.
2) Finora è stato utilizzato il banco A, canale 1 per creare un suono; ora
invece si procederà a salvarlo nel banco A, canale 2 dopo aver modificato leggermente la posizione di ogni controllo. Seguire le fasi seguenti.
Modificare il suono del
banco A, canale 1
Tenere premuto per
tre secondi o più
Il suono viene salvato
nel banco A, canale 2
Salvando il suono modificato in un altro canale, sarà possibile raffrontare i due suoni. Ora si passerà all'utilizzo di pattern ritmici.
Riprodurre un
pattern ritmico
Cambiare il
pattern ritmico
Cambiare la
velocità del ritmo
Si possono usare pattern ritmici seguendo la procedura sopra descritta.
5. Reimpostazione alla configurazione di fabbrica
Questa sezione spiega come inizializzare l'amplificatore nella condizione impostata in fabbrica.
1) Tenendo premuto lo switch MANUAL come mostrato nell'illustrazione
seguente, accendere lo switch 11 POWER. Il Display 5 indicherà AL.
2) Se si preme lo switch MANUAL in questo stato, tutti i dati ritorneranno
alla condizione impostata in fabbrica.
3) Se si decide di annullare la reimpostazione, utilizzare qualsiasi controllo che non sia lo switch MANUAL. In tal modo si esce dalla modalità
di reimpostazione alla configurazione di fabbrica.
Tenendo premuto lo switch
MANUAL, accendere lo switch
POWER.
Sezione preamplificatore: Controlla il tono della chitarra. I dettagli per ogni sezione sono
2
i seguenti.
1) AMP SELECTION (selezione amplificatore): Questa manopola permette di scegliere
tra undici modelli di preamplificatore. Per dettagli, consultare la sezione che descrive i vari
amplificatori.
2) GAIN (guadagno): Questa manopola di controllo regola il guadagno. La gamma di
ITALIANO
regolazione dipende dall'impostazione AMP SELECTION. Secondo il livello di GAIN, il
Display 5 indicherà un valore tra 0 e 100.
3) Equalizzatore: Costituito dalle tre manopole di controllo per i livelli (BASS, MIDDLE,
TREBLE: toni bassi, intermedi, acuti) dell'equalizzatore a tre bande. La gamma regolabile
e la funzione differiranno secondo l'impostazione di AMP SELECTION. Secondo il livello,
il Display 5 indicherà un valore tra -15 e 15.
4) VOLUME: Questa è la manopola di controllo per il livello in uscita del preamplificatore.
Secondo il livello del VOLUME, il Display 5 indicherà un valore tra 1 e 50. Il livello di
uscita sarà influenzato dal tipo di amplificatore selezionato, dal livello di guadagno e dal
livello dell'equalizzatore. Si può usare questo controllo per tenere costante il livello tra i
diversi canali, oltre che per definire il livello desiderato. Il volume finale è impostato dal
volume 10 MASTER.
Sezione memoria: Per salvare un suono creato, tenere premuto lo switch del canale dove
3
si intende salvare il suono per tre secondi o più. I dettagli sono descritti qui di seguito.
1) MANUAL (manuale): Questo switch seleziona la modalità manuale, dove tutte le
impostazioni audio rifletteranno la posizione effettiva dei controlli. Il Display 5 indicherà M.
2) Canali (1-5): Con questi switch si può scegliere uno dei cinque canali in cui si possono
memorizzare le proprie impostazioni. Vi sono due banchi (A e B) che permettono di memorizzare un totale di dieci suoni. In alternativa alla loro selezione dal pannello frontale, è
possibile collegare il controller a pedale opzionale IFC2 (venduto separatamente) e commutare i canali con il piede. Il Display 5 indicherà il numero di canale (1-5).
3) Switch banco A/B: Vi sono due banchi, ognuno contenente cinque canali.
Sezione batteria: È possibile usare cinquanta diversi pattern ritmici.
4
*L'illustrazione
precedente mostra
l'MIMX 150H.
1) Manopola RHYTHM (ritmo): Questa manopola controlla il volume
della batteria.
2) ON/OFF: Questo switch attiva/disattiva il pattern ritmico.
3) -/+: Questi switch permettono di scegliere tra cinquanta pattern
ritmici differenti. Per i dettagli su ogni pattern, leggere le SPECIFICHE.
4) Switch TAP: Controlla la velocità del ritmo in una gamma che va da
40 BPM a 199 BPM.
Display: Sono qui mostrate varie operazioni.
5
TUNER ON/OFF: L'MIMX ha un accordatore cromatico. Le illustrazioni seguenti mostra-
6
no quel che sarà indicato dal display quando è in funzione l'accordatore.
Si accende per indicare una
nota correttamente intonata
Movimento
del display
Quando la tonalità è
bassa
Sezione MODULATION (modulazione): Si possono controllare quattro tipi di effetti di
7
modulazione.
1) Manopola FX: Con questa manopola di controllo è possibile selezionare tra quattro tipi
di effetti di modulazione. Gli effetti disponibili sono i seguenti:
*L'illustrazione
precedente mostra
l'MIMX 150H.
2) Manopola MIX: Controlla il livello di mix dell'effetto di modulazione in una gamma che
va da 0 a 100. Ad un'impostazione di 0, l'effetto sarà disattivato; non sarà applicato alcun
effetto di modulazione.
3) Switch TAP: Controlla la velocità di modulazione dell'effetto di modulazione in una
gamma che va da 1 a 50. La tabella seguente mostra la velocità di modulazione controllabile
dallo switch TAP per ogni modalità.
Per i dettagli sul TAP, consultare "Informazioni sullo switch TAP".
Nota: Se si sta utilizzando l'effetto PEDAL PITCH della sezione 9 PEDAL FX, non sarà
possibile usare gli effetti della sezione MODULATION.
Quando la tonalità è
corretta: Mi intonato
a - CHORUS: Questo effetto crea un suono ricco creando sovrapposizioni
di suono e modulandole. Controllando la manopola FX si può variare la
profondità di modulazione in una gamma da 0 a 100.
b - FLANGER: Questo effetto applica modulazioni e sweep al suono. Controllando la manopola FX è possibile variare la profondità di modulazione in una gamma da 0 a 100.
c - VIBRATO: Questo effetto applica il vibrato. Controllando la manopola
FX è possibile variare la profondità di modulazione in una gamma che va
da 0 a 100.
d - STEP: Questo effetto varia il suono in modo step. Controllando la
manopola FX è possibile variare la profondità di modulazione in una
gamma che va da 0 a 100.
Sezione DELAY & REVERB (ritardo e riverbero): Si possono controllare quattro effetti Delay&Reverb differenti.
1) Manopola FX: Questa manopola di controllo seleziona uno dei quattro
effetti Delay&Reverb. Questi effetti sono elencati qui di seguito:
2) Manopola MIX: Controlla il livello del mix dell'effetto Delay&Reverb in una
gamma da 0 a 100. Sullo 0 l'effetto è disattivato e non vi è alcun effetto
Delay&Reverb.
3) Switch TAP: Quando si utilizza un DELAY o un ECHO, si può controllare il
tempo di ritardo dell'effetto. Quando si utilizza il REVERB, si controlla la lunghezza del riverbero. La tabella seguente mostra il tempo di delay e il tempo
di riverbero che è possibile controllare usando lo switch TAP in ciascuna
modalità.
Tempo
Contenuto del
Display
Per altri dettagli sul TAP, consultare la sezione sullo switch TAP.
Nota: Non si può usare REVERB quando si usa la sezione batteria 4.
a - DELAY: Questo effetto aggiunge una copia ritardata del
suono originale, in una sorta di "giro" musicale. Usare la manopola FX per variare il feedback nella gamma da 0 a 40.
b - ECHO: Questo effetto produce un effetto DELAY più
caldo. Usare la manopola FX per variare il feedback in
una gamma da 0 a 40.
c
-
REVERB HL: Questo riverbero simula l'acustica di un
grande ambiente, quale una sala da concerto. Usare la
manopola FX per variare le caratteristiche del riverbero
in una gamma da 0 a 10.
d
-
REVERB RM: Questo riverbero simula l'acustica di un
piccolo ambiente, quale quello di una stanza. Usare la
manopola FX per variare le caratteristiche del riverbero
in una gamma da 0 a 10.
Sezione PEDAL FX: Si possono controllare gli effetti a pedale usando un
controller a pedale opzionale IFC2 (venduto separatamente). Per i dettagli,
consultare "Altre informazioni sul controller a pedale."
1) Switch SELECT: Seleziona uno dei cinque tipi di effetti a pedale. Gli effetti
disponibili sono i seguenti:
-
VOL PEDAL (volume pedale): Questo è un pedale che
a
permette di controllare il volume con il piede.
b
-
RING MOD (modulazione a squillo): Questo effetto conferisce un timbro metallico al suono.
c
-
AUTO RESO (risonanza automatica): Questo effetto varia la frequenza risonante secondo la forza del picking.
d
-
WAH WAH: Effetto wah-wah.
e
-
PEDAL PITCH: Questo effetto permette di variare l'intonazione in tempo reale.
2) Manopola di controllo: Questa manopola controlla l'effetto della sezione
9
PEDAL FX. Gli effetti disponibili in ogni modalità sono i seguenti.
Posizione minimaPosizione massima
3) Jack switch a pedale: Si può usare lo switch a pedale collegando l'IFC2
venduto separatamente.
4) Jack pedale: Si può usare la sezione
opzionale (venduto separatamente).
10
Volume MASTER: Controlla l'uscita finale inviata all'altoparlante.
11
Switch POWER: interruttore per l'accensione/spegnimento dell'amplificatore.
12
AC INPUT (ingresso CA): Collegare qui il cavo di rete in dotazione.
13
LINE OUT (uscita linea) (MIMX 150H): Jack di uscita a livello di linea.
14
SPEAKER OUT (uscita diffusori) (MIMX 150H): Jack di uscita per altoparlanti. Usare un cavo apposito per collegarlo a un sistema di diffusione a 4Ω o a
8Ω.
Nota: Se si usa un set di altoparlanti la cui impedenza è inferiore a 4Ω, (ad
esempio a 2Ω), l'amplificatore di potenza si surriscalda, innescando un circuito
di protezione, e di conseguenza non si avrà un'uscita di segnale corretta.
15
HEADPHONES (cuffie) (MIMX65): Jack di uscita per le cuffie.
16
CD INPUT (ingresso CD) (MIMX65): Jack di ingresso a livello di linea. Qui è
9
PEDAL FX collegando l'IFC2
possibile collegare un lettore CD o MP3.
ITALIANO
85
Controllo AMP SELECTION
Il controllo AMP SELECTION permette la scelta tra undici tipi di
preamplificatori. Tra i numerosi tipi di amplificatori per chitarra esistenti,
Ibanez ha selezionato dieci classici dal suono immediatamente riconoscibile, e particolarmente apprezzati da molti chitarristi. Di ogni modello
sono state analizzate e riprodotte in ciascun preset tutte le caratteristiche principali, dall’ingresso dello strumento all’uscita dell’altoparlante.
MIMX è stato progettato in modo da ottenere facilmente suoni simili a
quelli degli amplificatori originali. Nell’impostazione di EQ di ciascun
ITALIANO
preset è stato considerato sia il suono complessivo dell’amplificatore
campionato, sia il comportamento timbrico dell’unità in risposta all’utiliz-
zo o meno dei controlli “Presence,” “Bright,” “Resonance” o “Deep,” in
modo da riprodurre il più fedelmente possibile i classici timbri a cui sono
associati. I preset non sono però delle repliche esatte, dato che Ibanez
ha preferito piuttosto avvicinarsi il più possibile alle “sensazioni sonore”
per cui questi amplificatori sono noti. Non manca, inoltre, un solido,
potente e compatto suono Ibanez originale, memorizzato nel preset
numero 11, che per l’occasione è stato ribattezzato “Psycho.”
NOTA: Nella descrizione dei preamplificatori che segue, i nomi dei prodotti non appartenenti a Ibanez sono stati utilizzati come riferimento per
far comprendere al meglio i suoni e timbri degli amplificatori che hanno
ispirato la creazione dei preset MIMX. Tali riferimenti e paragoni sono
del tutto soggettivi. Ibanez non intende in alcun modo affermare che i
preamplificatori MIMX rappresentano una copia esatta dei timbri a cui si
fa riferimento o utilizzati come termine di paragone. Detto questo, siamo
certi che il vostro nuovo MIMX e la sua vasta scelta di timbri saranno in
grado di soddisfare pienamente le vostre aspettative.
60s Clean:
Il suono di questo preset ricorda quello di uno dei classici amplificatori
costruiti da Fender®, il modello ’65 Twin Reverb®, impostato sul canale
NORMAL con l’interruttore BRIGHT in posizione OFF (disattivato). Per
averne un’idea, basti pensare al classico suono pulito in auge negli anni
’60. Il design sonoro di questo preamplificatore enfatizza gli alti cristallini
e i bassi solidi, un timbro tipicamente anni ’60, ma al tempo stesso piacevolmente originale.
Jazz Combo:
Preset ispirato dal suono del Roland® JC-120, noto per essere in grado
di mantenere inalterate le caratteristiche della chitarra usata, suonata
attraverso il canale CHANNEL 1 con l’interruttore BRIGHT in posizione
OFF (disattivato), e con una risposta timbrica complessivamente più
morbida. L’ampio range timbrico e la risposta neutra su tutto lo spettro di
questo preamplificatore, ne fanno la scelta ideale per l’uso combinato
con le unità multieffetti, a garanzia della massima versatilità.
70s Brit:
Questo suono evoca il modello Marshall® “JCM800 2203”, combinato
all’overdrive ottenuto grazie all’uso del pedale booster Ibanez®
TUBESCREAMER®/TS-9. Questo preset è in grado di soddisfare numerose esigenze sonore, dalle ritmiche solide agli assoli penetranti.
Brit Blues:
Il VOX® “AC30” è uno degli amplificatori che forse più di ogni altro è
riuscito, nella storia della musica, a recitare un ruolo da protagonista nel
blues, nel rock e nel pop. Dato che la sua fama è giunta fino ad oggi
inalterata, essendo ancora uno dei modelli più amati da molti musicisti,
quella di includere un preset ad esso ispirato è stata una scelta obbligata. Nella creazione del preset MIMX, è stato aggiunto maggiore guadagno e una risposta dei medi più tagliente e solida, incrementando l’im-
patto di un timbro già di per sé leggendario. Questo preset è molto sensibile alla dinamica, e risponde perciò fedelmente all’intensità con la
quale si colpiscono le corde con il plettro.
86
US Blues:
Preset che ricorda da vicino il Fender® “Hot Rod Deville™,” suonato
attraverso il canale DRIVE con il controllo BRIGHT in posizione NORMAL,
e il controllo MORE DRIVE su ON (attivato). Il modello MIMX si distingue dall’originale per un maggiore impatto dei bassi, e per l’impostazione
di EQ in modo shelving. Il risultato finale è un suono brillante, con una
risonanza piuttosto marcata. Da suoni ricchi di bassi con enfasi sullo
spettro grave, e fino a timbri ottenibili solo con un grande guadagno,
questo preamplificatore offre una vasta gamma di possibilità.
Rock:
Questo preset è la nostra versione del modello “Ecstasy 101B EL34
Version,” un versatile amplificatore a valvole costruito da Bogner
Corporation, un produttore famoso per l’elevata qualità componentistica
delle sue unità. Il preamplificatore offre un range dinamico migliorato a
qualsiasi livello di guadagno, e un maggiore controllo di livello per l’EQ.
Anche se spicca per la sua timbrica estrema, questo preset è l’ideale sia
per accordi puliti che distorti, sia per suoni ricchi di sustain.
Hard Rock:
Originariamente disponibile in pochi esemplari come amplificatore
custom, il modello Soldano® “SL0-100” riscosse in seguito un notevole
successo. Il suono di questo preset è simile a quello ottenibile dal canale OVERDRIVE dello SLO-100, con l’interruttore BRIGHT in posizione
NORMAL, ma con minore rischio di feedback e complessivamente maggiore tensione e compattezza. Il suono ad elevato guadagno è particolarmente buono, e rappresenta la scelta ottimale per le chitarre soliste e
i riff pesanti.
Guitar God:
Questa è la nostra versione del modello Peavey® “5150 II®”. Nella creazione di questo modello MIMX, si è tenuto in considerazione sia il timbro dell’amplificatore Peavey reale, sia le sonorità tratte dai CD musicali
degli artisti che lo usavano, in maniera da avvicinarsi il più possibile al
suono registrato. I bassi, solidi e compatti, sono l’ideale per i riff che
includono note stoppate, mentre la distorsione è quanto di meglio per
rendere memorabili gli assoli ricchi di sustain.
90s Brit:
Anche questo preset si basa sia su un amplificatore, in questo caso il
modello Marshall® “JCM2000 DSL100,” sia sui suoni tratti dai CD delle
band che lo usavano. La versione MIMX produce una distorsione piuttosto ruvida, con un timbro complessivo compatto e ben definito, con una
buona separazione delle note; può essere quindi usato per arpeggi risonanti e riff veloci. Con questo suono la chitarra è in grado di “uscire fuori”
dal mix in qualunque situazione, anche con una band molto potente.
LA Heavy:
La testata Mesa/Boogie® “Dual Rectifier® Solo Head” ha influenzato
numerosi musicisti dell’area heavy. Questo preamplificatore rappresen-
ta la nostra interpretazione di un collage di suoni classici, prodotti da un
modello introdotto nel 1989 e che da allora ha ridefinito il timbro della
chitarra heavy moderna. La nostra versione offre la tipica distorsione
generata in origine dalle valvole di potenza 6L6, utilizzando il canale
RED, l’alimentazione in modalità BOLD e il diodo in silicone del
rettificatore, con diffusione della cassa Ibanez® Thermion® TN412A
dotata di quattro coni da dodici pollici. Il risultato è un timbro mostruosamente compatto sui bassi e un buon crunch.
Psycho:
L’originale suono Ibanez, pensato per catturare il tipico suono della sce-
na heavy rock moderna. Il preset si distingue per i bassi solidi e taglienti,
e una vivacità superba. Regolando adeguatamente l’EQ, questo
preamplificatore può essere sfruttato per qualsiasi genere musicale.
*Ad eccezione di Ibanez®, TUBESCREAMER® e Thermion®, i nomi
delle aziende e dei prodotti menzionati in questo manuale sono
marchi o marchi registrati dai rispettivi proprietari, e non sono in alcun modo collegati a Ibanez.
Fender®, Twin Reverb®, Hot Rod Deville™ sono marchi o marchi
registrati di Fender Musical Instruments Corporation.
Roland®è un marchio registrato di Roland Corporation.
Marshall®è un marchio registrato di Marshall Amplification PLC.
VOX® è un marchio registrato di VOX R&D limited.
Soldano®è un marchio registrato di Soldano Custom Amplification.
Peavey® è un marchio registrato di Peavey Electronics LTD.
5150 II® è un marchio registrato di E.L.V.H., Inc.
Mesa/Boogie® e Dual Rectifier® sono marchi registrati di Mesa/
Boogie, Limited.
ITALIANO
87
Preimpostazioni di fabbrica
Sono le impostazioni audio assegnate a ciascun canale (da A1 a B5)
quando l'MIMX esce dalla fabbrica. Basta semplicemente premere un
tasto per ottenere le caratteristiche combinazioni di suoni ed effetti MIMX.
A1: Immortal Shred
AMP SELECTION (selezione amplificatore): Psycho
Questa impostazione è ideale per i riff veloci tipici dei gruppi slash metal
o death metal della scena musicale di oggi. La gamma dei toni medi
ITALIANO
viene tagliata per enfatizzare le gamme alte e basse, si può creare un
suono definito e robusto alzando i toni bassi senza ridurre eccessivamente i toni medi.
A2: Shrapnel Heroes
AMP SELECTION: Psycho
Questa impostazione può essere usata per gli assoli di chitarra di molti
generi, dall'hard rock all'heavy metal. L'equalizzazione dei toni è relativamente neutra. Se si aggiunge un delay abbastanza rapido, questa
impostazione produrrà un suono tipico adatto per gli assoli.
A3: Cruel Heaviness
AMP SELECTION: 90s Brit
Questa impostazione è per riff che enfatizzano la ritmica. È ideale per le
canzoni dal tempo lento e l'enfatizzazione della gamma dei toni bassi
produrrà un suono fortemente distorto che renderà amalgamato il suono della vostra band. È ideale per i suoni rock a volumi molto alti della
scena musicale odierna.
A4: Legend of the Beast
AMP STYLE (stile amplificatore): Hard Rock
Impostazione adatta alla solistica di chitarra per ottenere quel classico
suono Metal degli anni 80. Questa impostazione ha un carattere sonoro
che rievoca l'età d'oro del Metal, tipico di numerosi gruppi metal britannici e di Los Angeles.
A5: Emotional Clean
AMP STYLE: 60s Clean
Questa impostazione produce bassi corposi, un attacco secco e riverbero, per creare un'atmosfera calda. Usando un pickup single-coil si può
produrre un suono vintage brillante. Abbassando il livello del mix dell'effetto riverbero si può enfatizzare l'attacco.
B1: Sounds of the Right Hand
AMP SELECTION: Guitar God
Questa impostazione è ideale non solo per riff duri e serrati, ma anche
per le linee solistiche. La distorsione ottenuta aumentando il GAIN al
massimo e con toni medi robusti produce un'ottima combinazione per i
pickup humbucking. È stato applicato un leggero flanger per produrre
una sensazione di drive, ed un delay per creare un effetto di spazialità.
B2: Purple Tone
AMP SELECTION: Rock
Questa è una impostazione con alto gain, che taglia decisamente la
gamma dei toni bassi e aggiunge un carattere tipico ai toni medi. Usando un pickup single coil, è possibile riproporre il suono tipico della metà
degli anni '70. Aumentando il controllo MIDDLE, il suono assumerà un'atmosfera classica: regolare secondo il proprio gusto. Per godere a pieno
di questa impostazione, suonate i riff hard rock che erano rivoluzionari
all'epoca e sono divenuti la base dell'heavy rock di oggi.
B3: Crystal Clean
AMP SELECTION: Jazz Combo
Questa impostazione è stata creta per produrre suoni pulitissimi e chiari
come il cristallo. È in particolare adatta alle "Power Ballad" hard rock e
heavy metal degli anni '80 e '90. Con questa impostazione cercate di
suonare usando pickup single-coil , o con pickup centrale o con una
combinazione di pickup centrale e pickup al manico. Alzare il livello del
mix degli effetti per ottenere un suono più ricco.
B4: Solo DNA
AMP SELECTION: Rock
Questa impostazione è stata creata per riprodurre i suoni di assolo resi
famosi dai mitici chitarristi shredders degli anni '80! È un'impostazione
eccezionale per sbizzarrirsi con il proprio senso musicale. Utilizzate liberamente le tecniche di dive bombing e string bending ed esprimete la
vostra creatività con armonici, arpeggi sweep etc.
B5: Samurai Edge
AMP SELECTION: 70s Brit
Questa impostazione è una buona scelta per accompagnamenti ritmiciarmonici (comping) o riff blueseggianti suonati con un pickup single coil.
Fornisce la giusta dose di distorsione per accentuare le sfumature del
vostro picking, con picchi alti davvero asciutti. Regolare la quantità di
riverbero secondo il proprio gusto.
88
Utilizzo efficace dello switch TAP
L'MIMX ha uno switch TAP che si può utilizzare per controllare la velocità degli effetti e del ritmo. All'inizio potreste trovarlo insolito, ma sarete
presto in grado di usarlo facilmente e in modo intuitivo.
Premendo (colpendo leggermente) questo switch diverse volte (più di
due volte), potrete specificare la velocità desiderata. Continuando a premere, l'intervallo medio apparirà sul Display 5.
Per coloro che sono interessati ai dettagli "tecnici", qui di seguito viene
data una spiegazione dettagliata di come la funzione TAP rileva il tempo
medio.
Una media mobile
Un metodo detto "media mobile" viene usato per determinare la velocità
del tempo attraverso lo switch TAP. Ad esempio, se si vuole impostare il
tempo della batteria a 120 BPM, è abbastanza difficile specificare il tempo preciso semplicemente premendo lo switch TAP solo due volte.
Media mobile a quattro valori (qui useremo quattro valori per la nostra spiegazione)
L'intervallo medio tra le quattro pressioni più recenti dello switch TAP viene usato
come valore. Ciò permette di assorbire eventuali imprecisioni del tempo effettivamente scandito.
Valore di
1125bpm2115bpm3130bpm4109bpm
funzionamento
Valore di
uscita
1
125bpm120bpm121bpm119bpm123bpm
(1+2)
2
Media mobile a due valori
Occorre premere lo switch TAP ad un ritmo preciso, in modo
che l'intervallo tra la prima e la seconda pressione dello switch
TAP sia di 60/120 secondi = 0,5 secondi.
(1+2+3)3(1+2+3+4)4(2+3+4+5)
L'MIMX usa una media mobile di sette valori. Marcando i battiti con lo
switch TAP, si può ottenere un'impostazione di tempo più accurata.
5131bpm
4
Indicazione "modifica in corso" del display centrale
L'MIMX ha un LED "modifica in corso" che si accende come mostrato
nell'illustrazione seguente.
LED "modifica in
corso"
Posizione
della
manopola
Posizione del
suono effettivo
Quando si sposta il controllo sulla posizione che corrisponde al valore
memorizzato, scomparirà l'indicazione "modifica in corso". Questo è il
valore memorizzato nel canale selezionato.
Ecco un esempio.
1) Premere A1.
2) Spostare il controllo GAIN ad ore 12. Il
Display indicherà 50, e il punto si illuminerà. Ciò
indica che il guadagno è stato modificato ed è differente dal valore di guadagno in memoria.
3) Spostare il controllo GAIN sulla posizione massima. Il Display 5 indicherà 100, e il puntino si
spegnerà. Ciò indica che il valore di guadagno in
memoria viene indicato sul 5 Display.
* Questa funzione è prevista per tutti i controlli. Si può usarla per raffrontare i valori di controllo memorizzati con il valore corrente, o per controllare il contenuto memorizzato in ogni canale.
* Se si preme sullo switch MANUAL per selezionare la modalità manuale, la posizione di ogni controllo corrisponderà al valore effettivo che
determina il suono.
L'MIMX ha controlli rotanti di tipo analogico comodi da usare. Tuttavia, quando si preme uno switch dei canali A1-
-B5 per richiamare le impostazioni
memorizzate, le impostazioni audio
richiamate sulle manopole di controllo del pannello non corrisponderanno
necessariamente alla posizione fisica
delle manopole. Per questa ragione,
quando si preme uno switch del canale per richiamare una memoria e quindi
si sposta un controllo in una posizione differente dal valore memorizzato,
il LED "modifica in corso" in basso a
destra del Display 5 si illuminerà.
5
89
ITALIANO
Altre informazioni sul controller a pedale
Si può utilizzare l'IFC2 (venduto a parte) come controller per l'MIMX. Se
si collega l'IFC2, si potrà usare la sezione 9 PEDAL FX e utilizzare gli
switch a pedale per commutare i canali.
ITALIANO
a
e
d
b
f
c
A
B
Operazioni
a
Pedale Controlla l'effetto a pedale selezionato sull'amplificatore.
Switch Su: Commuta alla memoria immediatamente superiore ri-
b
spetto a quella attualmente selezionata. (Non funziona in modo
manuale).
c
Switch giù: Commuta alla memoria immediatamente inferiore rispetto a quella attualmente selezionata. (Non funziona in modo
manuale).
Premere b c simultaneamente per attivare l'accordatore.
d
Jack dello switch a pedale: Collegarlo all'amplificatore per usare gli
switch a pedale.
e
Jack dell'effetto a pedale: Collegarlo all'amplificatore per usare l'effetto a pedale. Un circuito all'interno dell'IFC2 permette all'MIMX di
riconoscere che il pedale è collegato.
Switch modalità: Questo switch determina la modalità di funziona-
f
mento del pedale. Impostarlo nel modo appropriato a seconda del
proprio stile musicale.
A
L'effetto rimane attivo anche quando il pedale è sul minimo (completamente girato verso l'utente).
B
L'effetto viene disattivato quando il pedale è sul minimo (completamente girato verso l'utente).
90
Risoluzioni di problemi
Innanzitutto, verificare che il cavo schermato della chitarra, il cavo del diffusore
e il cavo di alimentazione siano collegati correttamente. Se possibile, usare un
tester per controllare il cavo o provare a utilizzare un cavo o un amplificatore
alternativo per verificare la condizione del cavo.
1. L’apparecchiatura non si accende.
• Controllare che il cavo di alimentazione sia stato collegato correttamente.
• Provare a inserire la spina in un’altra presa di corrente e vedere se si verifica lo
stesso problema.
2. L’apparecchiatura si accende ma non si sente alcun
suono
• Controllare che la chitarra sia stata collegata correttamente.
• Togliere tutti i componenti esterni collegati al loop degli effetti e fra la chitarra e
l’amplificatore per verificare se il suono esce.
• Utilizzare un cavo schermato diverso e verificare se il suono esce.
• Verificare se il volume dell’amplificatore è regolato su “0”.
• Usare una chitarra diversa per verificare se il suono esce.
• Verificare se il volume dell’amplificatore è regolato su “0”.
• Verificare se le cuffie sono collegate.
• L'audio è ancora assente quando si alza il volume master?
• Verificare se si sta utilizzando il controller a pedale IFC2 (venduto a parte) come
pedale del volume, e se il pedale non sia completamente in posizione di ritorno
(cioè abbassato verso l'utente).
3. Si sente un rumore
• Verificare se c’è qualcosa vicino all’ amplificatore che risuona o che batte contro
l’amplificatore producendo il rumore.
• Verificare se il rivestimento della spina del cavo schermato è allentato.
• Accertarsi che la tensione delle corde della chitarra sia corretta.
• Usare chitarra, effetti, altri componenti esterni e cavo differenti per verificare se
viene prodotto lo stesso rumore.
4. Assenza di suono quando si collega un lettore CD
• Accertarsi che il volume del lettore CD non sia posizionato su 0.
• Accertarsi che il cavo sia collegato correttamente.
• Provare a utilizzare un altro cavo e verificare se si percepisce qualche suono.
5. L'audio del CD non è buono
Il cavo che si utilizza ha uno spinotto stereo? Si sta forse utilizzando uno spinotto mono?
6. Nessun suono è prodotto nelle cuffie
• Controllare che le cuffie siano inserite correttamente nella presa.
• Collegare un altro paio di cuffie e verificare se il suono arriva.
7. Nessun suono di batteria
• Verificare che il volume della batteria non sia su 0.
• Verificare che il volume master non sia su 0.
• Verificare che non siano collegate le cuffie.
8. L'effetto di modulazione non è attivo
• Verificare che il livello del mix non sia su 0.
• Verificare se si sta utilizzando l'accordatore incorporato nel MIMX.
• Verificare se si sta utilizzando il controller a pedale IFC2 (venduto a parte) per il
controllo del PEDAL PITCH.
9. L'effetto delay non è attivo
• Verificare che il livello del mix non sia su 0.
• Si verifica qualche cambiamento se si utilizza la funzione tap?
• Verificare se si sta utilizzando l'accordatore incorporato nel MIMX.
10. L'effetto riverbero non è attivo
• Verificare che il livello del mix non sia su 0.
• Verificare se si produce qualche cambiamento utilizzando la funzione tap.
• Verificare se si sta utilizzando la funzione Drum (batteria).
• Verificare se si sta utilizzando l'accordatore incorporato nel MIMX.
11. Non si può usare il pedale effetto
• Il controller a pedale IFC2 (venduto a parte) è collegato?
• Si sta utilizzando il cavo fornito in dotazione con l'IFC2?
• Verificare se si sta utilizzando l'accordatore incorporato nel MIMX.
In caso di difetti:
Questo prodotto è stato sottoposto a rigide ispezioni prima di essere spedito
dalla fabbrica. Accertarsi che i procedimenti sopraelencati siano eseguiti quando
si pensa di trovarsi di fronte a un problema. Rivolgersi al rivenditore nell ’
eventualità che si verifichi qualche anomalia durante l ’uso. Inoltre, accertarsi
che le caratteristiche del problema vengano spiegate dettagliatamente
quando si richiede una riparazione in modo da facilitarne una esecuzione rapida.
Date le migliorie apportate al questo prodotto,le specifiche possono cambiare
senza previo avviso.