iBall Baton iB-W4GX150N User Manual

4G Wireless-N Router

Model No. iB-W4GX150N

User Guide

Ver.: 1.0.0

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause
undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures

I

CONTENTS

Package Contents ............................................................................................................................. 1

Chapter 1. Introduction ................................................................................................................... 2

1.1 Overview of the Router ................................................................................................... 2

1.2 Conventions .................................................................................................................... 2

1.3 Main Features ................................................................................................................. 3

1.4 Panel Layout ................................................................................................................... 4

1.4.1 The Front Panel .................................................................................................. 4

1.4.2 The Rear Panel ................................................................................................... 5

Chapter 2. Connecting the Router ................................................................................................. 6

2.1 System Requirements .................................................................................................... 6

2.2 Installation Environment Requirements .......................................................................... 6

2.3 Connecting the Router .................................................................................................... 6

Chapter 3. Quick Installation Guide ............................................................................................... 8

3.1 TCP/IP Configuration ...................................................................................................... 8

3.2 Quick Installation Guide ................................................................................................ 10

Chapter 4. Configuring the Router ............................................................................................... 18

4.1 Login ............................................................................................................................. 18

4.2 Status ............................................................................................................................ 18

4.3 Quick Setup .................................................................................................................. 20

4.4 WPS .............................................................................................................................. 20

4.5 Network Setting............................................................................................................. 26

4.5.1 Operation Mode .................................................................................................. 26

4.5.2 3G/4G ................................................................................................................ 28

4.5.3 WAN .................................................................................................................. 31

4.5.4 MAC Clone ........................................................................................................ 41

4.5.5 LAN ................................................................................................................... 42

4.6 Wireless ........................................................................................................................ 43

4.6.1 Wireless Settings .............................................................................................. 43

4.6.2 Wireless Security .............................................................................................. 46

4.6.3 Wireless MAC Filtering ..................................................................................... 50

4.6.4 Wireless Advanced ........................................................................................... 52

4.6.5 Wireless Statistics ............................................................................................. 53

II

4.7 DHCP ............................................................................................................................ 54

4.7.1 DHCP Settings .................................................................................................. 54

4.7.2 DHCP Clients List ............................................................................................. 55

4.7.3 Address Reservation......................................................................................... 56

4.8 Forwarding .................................................................................................................... 57

4.8.1 Virtual Servers................................................................................................... 57

4.8.2 Port Triggering .................................................................................................. 59

4.8.3 DMZ .................................................................................................................. 61

4.8.4 UPnP ................................................................................................................. 62

4.9 Security ......................................................................................................................... 63

4.9.1 Basic Security ................................................................................................... 63

4.9.2 Advanced Security ............................................................................................ 65

4.9.3 Local Management ........................................................................................... 67

4.9.4 Remote Management ....................................................................................... 68

4.10 Parental Control ............................................................................................................ 69

4.11 Access Restriction ........................................................................................................ 72

4.11.1 Rule ................................................................................................................... 72

4.11.2 Host (LAN) ........................................................................................................ 75

4.11.3 Target WAN) ...................................................................................................... 77

4.11.4 Schedule ........................................................................................................... 79

4.12 Static Routing ................................................................................................................ 80

4.12.1 Static Routing List ............................................................................................. 81

4.12.2 System Routing Table ....................................................................................... 82

4.13 Bandwidth Control......................................................................................................... 82

4.13.1 Control Settings ................................................................................................ 82

4.13.2 Rules List .......................................................................................................... 83

4.14 IP & MAC Binding Setting ............................................................................................. 84

4.14.1 Binding Setting .................................................................................................. 84

4.14.2 ARP List ............................................................................................................ 86

4.15 Dynamic DNS ............................................................................................................... 87

4.15.1 Comexe.cn DDNS ............................................................................................. 87

4.15.2 Dyndns.org DDNS ............................................................................................ 88

4.15.3 No-ip.com DDNS .............................................................................................. 89

4.16 System Tools ................................................................................................................. 90

4.16.1 Time Setting ...................................................................................................... 91

4.16.2 Diagnostic ......................................................................................................... 92

4.16.3 Firmware Upgrade ............................................................................................ 93

III

4.16.4 Factory Defaults ................................................................................................ 94

4.16.5 Backup & Restore ............................................................................................. 95

4.16.6 Restart ............................................................................................................... 96

4.16.7 Password .......................................................................................................... 96

4.16.8 System Log ....................................................................................................... 97

4.16.9 Statistics ............................................................................................................ 99

Appendix A: FAQ ........................................................................................................................... 101

Appendix B: Configuring the PCs ............................................................................................... 107

Appendix C: Specifications ......................................................................................................... 111

Appendix D: Glossary ................................................................................................................... 112

Appendix E: Compatible 3G USB Modem .................................................................................. 114

Appendix F: Contact details ......................................................................................................... 114

iB-W4GX150N

4G Wireless-N Router

-1-

Package Contents

The following items should be found in your package:

 4G Wireless-N Router (iB-W4GX150N)
 Antenna (Fixed)
 Power Adapter
 Cd
 Quick Installation Guide
 RJ45 Patch cord

 Resource CD for iB-W4GX150N 4G Wireless-N Router, including:

 This Guide
 Other Helpful Information

Conventions

The Router or iB-W4GX150N mentioned in this guide stands for iBallBaton 4G Wirelesses-N Router
without any explanation.



Note:

Make sure that the package contains the above items. If any of the listed items is damaged or
missing, please contact your distributor.

iB-W4GX150N

4G Wireless-N Router

-2-

Chapter 1. Introduction

Thank you for choosing iBall Baton 4G Wireless-N Router.

1.1 Overview of the Router

Thank you for choosing iBall Baton 4G Wireless-N Router.

1.2 Overview of the Router

iB-W4GX150N 4G Wirelesses-N Router complies with IEEE 802.11 b/g/n wireless standards.
Enhanced Wireless data transmission speed up to 150Mbps
With 4-10/100M LAN Ports, 1 - 10/100M WAN Port for Broadband Internet (Cable/DSL) & USB

slot for 4G/3G Internet.

4G/3G Internet - USB slot for GSM/CDMA compatible data card
Broadband Internet - Configure internet through (RJ45) WAN Port

Auto WAN failover with 3G Backup

With multiple protection measures, including SSID broadcast control and wireless LAN
64/128/152-bit WEP encryption, WiFi protected Access (WPA2- PSK, WPA- PSK), as well as
advanced Firewall protections, the iB-W4GX150N Router provides complete data privacy.

The 4G Wireless-N Router provides flexible access control, so that parents or network
administrators can establish restricted access policies for children or staff. It also supports Virtual
Server and DMZ host for Port Triggering, and then the network administrators can manage and
monitor the network in real time with the remote management function.

Flexible Access Control

Multiple Security Protections

Dual WAN Router

4G/3G Backup (Failover connection)

iB-W4GX150N

4G Wireless-N Router

-3-

1.3 Main Features

 Complies with IEEE802.3, IEEE 802.3u standards
 Complies with IEEE 802.11b/g/n wireless standards
 1- 10/100M WAN Port, 4- 10/100M LAN Ports & Wireless-N AP
 Dual WAN Router with different Operation Modes:

 3G/4G Connection with Broadband Failover
 3G/4G Connection
 3G/4G Backup - Broadband Connection with 3G Failover

 Broadband Connection
 Multi-SSID security feature
 Firewall security features as:

 Access Restriction (Time & Schedule based)

 Parental Control (IP, MAC & Domain filtering)

 DoS

 With WEP, WPA & WPA2 encryption security
 Built-in NAT and DHCP Server
 Remote & Local management
 Provides Diagnostic Tools - Ping & Trace-route
 5dBi Omni-Directional Antenna
 Power Adapter: 9V DC, 0.85A

iB-W4GX150N

4G Wireless-N Router

-4-

1.4 Panel Layout

1.4.1 The Front Panel

Figure 1-1 Front Panel sketch

The Router’s LEDs and the WPS/Reset Button are located on the front panel (View from left to
right).

Name

Status

Indication

PWR

On

Power is on.

Off

Power is off.

SYS

On

The Router is initializing.

Flashing

The Router is working properly.

Off

The Router has a system error.

WLAN
Flashing

The Wireless function is enabled.

Off

The Wireless function is disabled.

WAN,

LAN1-4

On

A device is linked to the corresponding port but there is no activity.

Flashing

An active device is linked to the corresponding port.

Off

No device is linked to the corresponding port.

3G

On

The USB 3G dongle is connected.

Flashing

Data is received or sent through the 3G dongle.

Off

No device is linked to the USB port.

WPS/Reset

Slow Flash

A wireless device is connecting to the network by WPS function.
This process will last for about 2 minutes.

On

A wireless device has been successfully added to the network by
WPS function. The LED will keep on for about 5 minutes.

Quick Flash

A wireless device has failed to be added to the network by WPS
function.

Table 1-1 The LEDs description



Note:

1. When a device has been successfully added to the network by WPS function, the WPS

LED will keep on for about 5 minutes and then turn off.

2. When pressing and holding the WPS/Reset Button for more than 5 seconds, you will reset

the router.

iB-W4GX150N

4G Wireless-N Router

-5-

1.4.2 The Rear Panel

Figure 1-2 Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
 POWER: The Power socket is where you will connect the power adapter. Please use the

power adapter provided with this IB-W4GX150N 4G Wireless-N Router.

 ON/OFF: The switch for the power.
 WAN: This WAN port is where you will connect the DSL/cable Modem, or Ethernet
 1,2,3,4 (LAN): These ports (1, 2, 3, 4) connect the Router to the local PC(s)
 USB: Connect to the USB Modem.
 Wireless antenna: To receive and transmit the wireless data.

iB-W4GX150N

4G Wireless-N Router

-6-

Chapter 2. Connecting the Router

2.1 System Requirements

Before installing the device, please make sure your Broadband service or 4G/3G service provided
by your ISP is available.
(For 4G/3G verify the SIM service is activated) kindly contact your ISP related to service problem.

a. Power off your PC, Cable/DSL modem, and the Router.
b. Locate an optimum location for the Router. The best place is usually near the center of the

area in which your PC(s) will wirelessly connect.
c. Adjust the direction of the antenna. Normally, upright is a good direction.
d. Configure the Internet connection as below steps

Broadband Connection

Step-I: Plug the RJ45 cable into LAN port (1~4) and another end to your PC or Laptop
Step-II: Plug the Internet cable connection into router WAN port (RJ45)

Or

3G/4G Connection

Step-I: Plug the RJ45 cable into LAN port (1~4) and another end to your PC or Laptop
Step-II: Plug the 3G/4G USB Modem (Data Card) into the router USB slot

Note: Activated SIM card needs to be inserted in USB modem before plug into the router

iB-W4GX150N

4G Wireless-N Router

-7-

2.2 Connecting the Router

Connect the 4G/3G USB Modem or DSL/Cable Modem/Ethernet to the WAN port of the Router,
shown in the figure (2-1)

(Figure 2.1)

Figure 2-1 Hardware Installation of the IB-W4GX150N 4G Wireless-N Router

e. Connect the power adapter to the power socket on the Router, and the other end into an

electrical outlet.
f. Power on your PC, the Router and Cable/DSL modem.
g. When all of the devices boot up completely, make sure that the Router's LEDs light as follows:

 Power LED: Light up

 System LED: Flashing

 4G/3G: Light up if USB Modem Inserted.

 WLAN LED: Flashing or Light up

 WAN&LAN LED: Light up or flashing if the port is connected

iB-W4GX150N

4G Wireless-N Router

-8-

2.3 Installation Environment Requirements

 Place the Router in a well ventilated place far from any heater or heating vent
 Avoid direct irradiation of any strong light (such as sunlight)
 Keep at least 2 inches (5 cm) of clear space around the Router
 Operating Temperature: 0°C~40°C (32°C ~104°C)
 Operating Humidity: 10%~90%RH, Non-condensing

2.4 Connecting the Router

Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that,
please install the Router according to the following steps. Don't forget to pull out the power plug
and keep your hands dry.

1. Power off your PC, Cable/DSL Modem, and the Router.

2. Locate an optimum location for the Router. The best place is usually at the center of your

wireless network. The place must accord with the Installation Environment Requirements.

3. Adjust the direction of the antenna. Normally, upright is a good direction.

4. Connect the PC or Switch/Hub in your LAN to the LAN Ports of the 3G Router with Ethernet

cable, shown in Figure 2-1.

5. The 3G Router supports both 3G and WAN connection, so you can insert 3G USB Modem

and Connect the DSL/Cable Modem to the WAN port of the 3G Router, shown in Figure 2-1.
Please visit our website to get the latest USB modems compatibility, and we recommend
you to check whether the modem in your hand has already been tested by us.

6. Connect the power adapter to the power socket on the Router, and the other end into an

electrical outlet. The Router will start to work automatically.

7. Power on your PC and Cable/DSL Modem.

iB-W4GX150N

4G Wireless-N Router

-9-

Chapter 3. Quick Installation Guide

This chapter will show you how to configure the basic functions of your 4G Wireless-N Router
IB-W4GX150N using Quick Setup Wizard within minutes.

3.1 TCP/IP Configuration

The default IP address of the 4G Wireless-N Router IB-W4GX150N is 192.168.1.1. And the
default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this
guide, we use all the default values for description.

Connect the local PC to the LAN ports of the Router. And then you can configure the IP address
for your PC in the following two ways.

 Configure the IP address manually

1) Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to Appendix B: "Configuring the PC."

2) Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any
number from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1
(The Router's default IP address)

 Obtain an IP address automatically

1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your
PC. If you need instructions as to how to do this, please refer to Appendix B:

"Configuring the PC."

2) Then the built-in DHCP server will assign IP address for the PC.

Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and the Router. The following example is in Windows 2000 OS.

Open a command prompt, and type ping 192.168.1.1, and then press Enter.
 If the result displayed is similar to Figure 3-1, it means the connection between your PC

and the Router has been established well.

iB-W4GX150N

4G Wireless-N Router

-10-

Figure 3-1 Success result of Ping command

 If the result displayed is similar to Figure 3-2, it means the connection between your PC

and the Router has failed.

Figure 3-2 Failure result of Ping command

Please check the connection following these steps:

1. Is the connection between your PC and the Router correct?



Note:

The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter
should be lit.

iB-W4GX150N

4G Wireless-N Router

-11-

2. Is the TCP/IP configuration for your PC correct?



Note:

If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of

192.168.1.2 ~ 192.168.1.254.

3.2 Quick Installation Guide

With a Web-based (Internet Explorer or Firefox) utility, it is easy to configure and manage the
4G Wireless-N Router, IB-W4GX150N. The Web-based utility can be used on any Windows,
Macintosh or UNIX OS with a Web browser.

1. To access the configuration utility, open a web-browser and type in the default address

http://192.168.1.1 in the address field of the browser.

Figure 3-3 Login the Router

After a moment, a login window will appear, similar to Figure 3-4. Enter admin for the User
Name and Password, both in lower case letters. Then click the OK button or press the Enter
key.

Figure 3-4 Login Window



Note:

If the above screen does not pop up, it means that your Web-browser has been set to a proxy.
Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.

2. After successfully login in, you can click the Quick Setup to quickly configure your Router.

iB-W4GX150N

4G Wireless-N Router

-12-

Figure 3-5 Quick Setup

3. Click Next, and then Internet Access page will appear, shown in Figure 3-6. Select a
desired Internet access mode and then click Next. The configuration for each mode is
similar. Here we take 3G Preferred mode for example.

Figure 3-6 Choose Internet Access Mode

 3G/4G Connection with Broadband Failover

In this mode, the router will try 3G access first. If 3G access fails and WAN access is valid,
or if no 3G USB modem is inserted, the router would switch to WAN access. Once the
router succeeds to connect to the 3G network, the router would stop the WAN connection
and switch back to 3G access immediately.

 3G/4G Connection

In this mode, the router will try 3G access only. WAN access is disabled.

 Broadband Connection with 3G/4G Failover

In this mode, the router will try WAN access first. If the WAN access fails, and 3G access is
valid, the router would switch to 3G access. Once the router succeeds to connect to the
WAN network, the router would stop the 3G connection and switch back to WAN access
immediately.

iB-W4GX150N

4G Wireless-N Router

-13-

 Broadband Connection

In this mode, the router will try WAN access only. 3G access is disabled.

4. The next screen will appear as shown in Figure 3-7. After finishing the configuration on this
page, click Next to continue,

Figure 3-7 3G

 Location - Select the location where you're enjoying the 3G card.
 Mobile ISP - Select the ISP (Internet Service Provider) you apply to for 3G service. The

router will show the default Dial Number and APN of that ISP. If your ISP is not listed in the
Mobile ISP, check the box before Set the Dial Number and APN manually and fill the Dial
Number and APN blanks below.

 Dial Number & APN - Fill these two parameters manually after Set the Dial Number and

APN manually is checked.

 Username & Password - Enter the Username and Password provided by your ISP. These

fields are optional but case-sensitive.

5. You will then see Figure 3-8. Select Auto-Detect, the Router will automatically detect the
connection type your ISP provides. Make sure the cable is securely plugged into the WAN
port before detection. The appropriate configuration page will be displayed when an active
Internet service is successfully detected by the Router.

iB-W4GX150N

4G Wireless-N Router

-14-

Figure 3-8 WAN Connection Type

 If the connection type detected is PPPoE, the next screen will appear as shown in Figure 3-9.

Enter the User Name and Password provided by your ISP. These fields are case-sensitive. If
you have difficulty with this process, please contact your ISP.

Figure 3-9 Quick Setup – PPPoE

 If the connection type detected is Dynamic IP, the next screen will appear as shown in

Figure 3-10.

 If you are visiting the Router from the main computer, please select Yes, and then

click Clone MAC Address.

Figure 3-10 Quick Setup – MAC Clone

iB-W4GX150N

4G Wireless-N Router

-15-

 If you are visiting the Router from another computer, rather than the main

computer, please select No, and then enter the main computer’s MAC in the field
WAN MAC Address.

Figure 3-11 Quick Setup – MAC Clone

 If the connection type detected is Static IP, the next screen will appear as shown in Figure

3-12. Enter the parameters in the corresponding blanks.

Figure 3-12 Quick Setup - Static IP

6. Click Next to continue, the Wireless settings page will appear as shown in Figure 3-13.

Figure 3-13 Quick Setup – Wireless

iB-W4GX150N

4G Wireless-N Router

-16-

 Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list.
 SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set

Identification) must be assigned to all wireless devices in your network. Considering your
wireless network security, the default SSID is set to be Wireless_XXXXXX (XXXXXX
indicates the last unique six numbers of each Router’s MAC address). This value is
case-sensitive. For example, TEST is NOT the same as test.

 Region - Select your region from the pull-down list. This field specifies the region where

the wireless function of the Router can be used. It may be illegal to use the wireless
function of the Router in a region other than one of those specified in this field. If your
country or region is not listed, please contact your local government agency for
assistance.

 Channel - This field determines which operating frequency will be used. The default

channel is set to Auto, so the AP will choose the best channel automatically. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point.

 Mode - This field determines the wireless mode which the Router works on.
 Channel Width - Select any channel width from the pull-down list. The default setting is

automatic, which can adjust the channel width for your clients automatically.

 Wireless Security - You can select one of the following security options.

 Disable Security - The wireless security function can be enabled or disabled. If

disabled, the wireless stations will be able to connect to the Router without encryption.
It is recommended strongly that you choose one of following options to enable
security.

 WPA-Personal/WPA2-Personal - Select WPA based on pre-shared passphrase.

Password - You can enter ASCII or Hexadecimal characters.
For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the

length should be between 8 and 63 characters.
For Hexadecimal, the key can be made up of any numbers 0 to 9 and letters A to F,

the length should be between 8 and 64 characters.
Please also note the key is case-sensitive, this means that upper and lower case keys

will affect the outcome. It would also be a good idea to write down the key and all
related wireless security settings.

 Use the Previous settings - If you chose this option, wireless security configuration

will not change.

These settings are only for basic wireless parameters. For advanced settings, please refer to

Section 4.6: “Wireless”.

iB-W4GX150N

4G Wireless-N Router

-17-

7. Click the Next button. You will then see the Finish page.
If you don’t make any change on the Wireless page, you will see the Finish page as

shown in Figure 3-14. Click the Finish button to finish the Quick Setup.

Figure 3-14 Quick Setup – Finish

If there is something changed on the Wireless page, you will see the Finish page as
shown in Figure 3-15. Click the Reboot button to make your wireless configuration to take
effect and finish the Quick Setup.

Figure 3-15 Quick Setup – Finish

After the rebooting, please check whether you can access the Internet or not in the 4.2 Status
page.

iB-W4GX150N

4G Wireless-N Router

-18-

Chapter 4. Configuring the Router

This chapter will show each Web page's key functions and the configuration way.

4.1 Login

After your successful login, you will see the fifteen main menus on the left of the Web-based utility.
On the right, there are the corresponding explanations and instructions.

The detailed explanations for each Web page’s key function are listed below.

4.2 Status

The Status page provides the current status information about the Router. All information is
read-only.

iB-W4GX150N

4G Wireless-N Router

-19-

Figure 4-1 Router Status

4.3 Quick Setup

Please refer to Section 3.2: "Quick Installation Guide."

iB-W4GX150N

4G Wireless-N Router

-20-

4.4 WPS

This section will guide you to add a new wireless device to an existing network quickly by WPS
(Wi-Fi Protected Setup) function.

a). Choose menu “WPS”, you will see the next screen (shown in Figure 4-2 ).

Figure 4-2 WPS

 WPS Status - Enable or disable the WPS function here.
 Current PIN - The current value of the Router's PIN displayed here. The default PIN of the

Router can be found in the label or User Guide.

 Restore PIN - Restore the PIN of the Router to its default.
 Gen New PIN - Click this button, and then you can get a new random value for the

Router's PIN. You can ensure the network security by generating a new PIN.

 Add device - You can add the new device to the existing network manually by clicking this

button.

b). To add a new device:
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless

connection between wireless adapter and Router using either Push Button Configuration (PBC)
method or PIN method.



Note:

To build a successful connection by WPS, you should also do the corresponding configuration
of the new device for WPS function meanwhile.

For the configuration of the new device, here takes the Wireless Adapter of our company for
example.

I. By PBC

If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC)
method, you can add it to the network by PBC with the following two methods.

Method One: Press the WPS/Reset Button on the front panel of the Router.

iB-W4GX150N

4G Wireless-N Router

-21-



Note:

When pressing and holding the WPS/Reset Button for more than 5 seconds, you will reset the
router.

Step 1: Press and hold the WPS Button of the adapter directly for 2 or 3 seconds.

Step 2: Wait for a while until the next screen appears. Click Finish to complete the WPS

configuration.

The WPS Configuration Screen of Wireless Adapter

Method Two:

Step 1: Press the WPS/Reset Button on the front panel of the Router.



Note:

When pressing and holding the WPS/Reset Button for more than 5 seconds, you will reset the
router.

Step 2: For the configuration of the wireless adapter, please choose Push the button on my

access point in the configuration utility of the WPS as below, and click Next.

iB-W4GX150N

4G Wireless-N Router

-22-

The WPS Configuration Screen of Wireless Adapter

Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS

configuration.

The WPS Configuration Screen of Wireless Adapter

iB-W4GX150N

4G Wireless-N Router

-23-

Method Three:

Step 1: Keep the default WPS Status as Enabled and click the Add device button in Figure

4-2, then the following screen will appear.

Figure 4-3 Add A New Device

Step 2: Choose Press the button of the new device in two minutes and click Connect.
Step 3: For the configuration of the wireless adapter, please choose Push the button on my

access point in the configuration utility of the WPS as below, and click Next.

The WPS Configuration Screen of Wireless Adapter

Step 4: Wait for a while until the next screen appears. Click Finish to complete the WPS

configuration.

iB-W4GX150N

4G Wireless-N Router

-24-

The WPS Configuration Screen of Wireless Adapter

II. By PIN

If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the
network by PIN with the following two methods.

Method One: Enter the PIN into my Router
Step 1: Keep the default WPS Status as Enabled and click the Add device button in Figure

4-2, then the following screen will appear.

Step 2: Choose Enter the new device's PIN and enter the PIN code of the wireless adapter in

the field behind PIN in the above figure. Then click Connect.



Note:

The PIN code of the adapter is always displayed on the WPS configuration screen.

Step 3: For the configuration of the wireless adapter, please choose Enter a PIN into my

access point or a registrar in the configuration utility of the WPS as below, and click
Next.