iBall Baton iB-W3GB150N User Manual

3G+ Wi-Fi Travel Router (with Built-in Battery)

Model No. iB-W3GB150N

User Manual

Ver.: 1.0.0

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Contents

3G+ WI-FI TRAVEL ROUTER(WITH BUILT-IN BATTERY).........................................1

MODEL NO. IB-W3GB150N..........................................................................................1

CHAPTER 1INTRODUCTION............................................................ ..........................5

CHAPTER 2. CONFIGURING THE ROUTER .......................................................... ..10

CHAPTER 3 NETWORK SETTINGS................................ ..... ... .. ...... .. ...... .. ... ..... ... ... 222

3.2 FORWARDING............................................................ .. ...... .. ...... .. ...... .. ... ..... ... ...377 

3.3 SECURITY SETTINGS........................................ .. ...... .. ...... .. ... ..... ... ... ..... ... ..... ... ..40

3.4 ADVANCED SETTINGS.............................................................. .. ...... .. ... ..... ... .....46

3.5 SYSTEM TOOLS...................................................... ... .. ...... .. ...... .. ... ..... ... ..... ... ... ..54

CHAPTER 4. TROUBLESHOOTING................................................ ..... ... .. ...... .. ...... ..57

APPENDIX A. SPEC SUMMARY TABLE...................................................................61

APPENDIX B. GLOSSARY .........................................................................................62

APPENDIX C. CONTACT INFORMATION.................................................................63

Chapter 1 Introduction

iBall Baton 3G+ Wi-Fi Travel Router (with Built-in Battery) User Manual will help you to install and configure quickly & easily.

¾ Compact design ideal for travel use ¾ Enhanced 150Mbps wireless transmission speed.

¾ Auto-Failover function ¾ With Lion Battery to access internet anytime and anywhere

Combo Router

Supports Dual WAN Connection

¾ 2G/3G+ Network support (HSPA+, WCDMA, CDMA & EV-DO) - USB port ¾ Broadband Internet (Cable/ DSL) - Ethernet port

Easy Setup Wizard - Utility helps users to configure the router easily.

Package contents

The following contents should be found in the product packaging:

Items Description Contents Quantity

3G+ Wi-Fi Travel Router

Power adapter Universal Power Adapter

User Guide & Utility

QIG Print Copy

Li-ion Battery

RJ45 Patch Cord

)

Note:

Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your nearest dealer.

A. Hardware Installation

B. LED indicators

Power LED indicator:

Power Source ON/OFF Switch LED Status Description

ON Green in flash Device ON, and Battery is in use. ON Red Device ON, and Battery is low.

Battery Only

OFF N/A Device OFF

ON Green

Device ON, and Battery is fully charged.

ON Amber

Device ON, and Battery is charging

ON Red in Flash

Device ON, Battery is charging , and System Temperature is too high and ready to shut down

OFF Amber

Device OFF, and Battery is charging.

Power Adapter

OFF N/A Device OFF

Other LED indicator:

LED Status Description Green

RJ45 cable is plugged, and Ethernet connection is established.

Ethernet LED

Green in flash Data access Blue 2G/3G Data Card is on

USB LED

Blue in flash Data access Blue WLAN is on

Wi-Fi LED

Blue in flash Data access

C. Installation Steps

Step 1. Install the battery:

Turn OFF the power switch, open the battery lid, and then insert the Li-ion battery into the battery holder.

Battery needs to stay in the compartment to power-on the device.

Step 2.

Close the battery lid

Step 3. Plug in power:

Connect with the power adapter to the recep to r on the back panel of it.

Step 4. Start to Charge the Battery:

Then plug the other end of the power adapter into a wall outlet.

If it is the first time to put the battery in, the power LED will show amber which means the battery is been charging. It will take about 3 hours to fully charge the battery, and when the battery is fully charged, the power LED will show green.

Step 5. Power ON:

Turn ON the power switch.

Step 6. Connect with a USB 3G modem:

Plug your USB modem which is with activated SIM card provided by your 3G service provider.

Step 7. Connect with Ethernet Cable

Insert the Ethernet cable into RJ45 Ethernet Port on the back panel. And then plug the other end of RJ45 into the computer or Laptop computer. The Ethernet LED will show green color if the Ethernet connection is normally connected.

Chapter 2. Configuring the Router

There are two methods for you to set up the iB-W3GB150N Router quickly and easily.

Method - I Easy Setup Wizard Method - II Web Based configuring through browser

Method - I Easy Setup Wizard

Configuring the Router via Easy Setup Wizard (Resource CD)

a. Insert the Resource CD into your CD-ROM device.

b. The Easy Setup Wizard will automatically pop up on the computer’s screen.

Click START button and follow the steps as per easy setup configuration to complete the router configuration

Chapter 2.1

Easy Setup Wizard - (Utility Software)

Step 1：

Run the Easy Setup Wizard from the provided CD then follow the steps to configure the device.

Step 2：

Select Language then click “Next” to continue.

Step 3：

Then click the “Quick Wizard” to continue.

Step 4：

Click “Next” to continue.

Step 5：

Select Wireless Enable, and then click “Next” to continue.

Step 6：

Enter SSID, Channel and Security options, and then click “Next” to continue.

Default Parameters:

SSID: iBall-Baton Password: 12345678

Step 7：

Click” Let me select WAN service by myself” to select WAN service manually.

Step 8：

Select Ethernet WAN Service by clicking Ethernet WAN icon to configure Ethernet WAN Connection.

Step 9 : Select Ethernet WAN Connection Type by clicking on proper icon to continue

Step 10 : Select Ethernet / Wireless WAN Connection type by clicking on proper icon to continue

Step 11 : Wireless WAN Connection Type will display 3G or iBurst menu - Click the proper menu as per your ISP settings to continue

Step 12-1：

¾ Auto-Detection

In “Auto-Detection” mode WAN Service will try to detect and configure the required 3G service settings automatically.

Click “Next” to continue.

Step 12-2：

¾ Manual

In “Manual” WAN Service you will need to insert the required 3G service settings as provided by your ISP.

Click “Next” to continue

Step 13:

Click “Next” to save your setting.

Step 14:

The 3G+ Wi-Fi Travel Router is rebooted to make your entire configuration take effect.

Step 15：

Click “Next” to WAN Networking service.

Step 16：

Click “Next” to test the Internet connection or you Can ignore test.

Step 17：

Setup is completed.

Method – II Configuring the Router by Web Console

With a Web-based utility, it is easy to configure and manage the iB-W3GB150N 3G+ W i -Fi Travel Router (with Built-in Battery).

The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.

To login to the router, you should set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC(s ).

a. To access the configuration utility, open a web-browser and type in the default address

http://192.168.1.1 in the address field of the browser.

I. After a moment, a login window will appear. Enter admin for the User Name

and Password, both in lower case letters. Then click OK or press Enter.

2.2.1 Configure with the Quick Setup Default Router Settings

IP Address: 192.168.1.1 Login Password: admin

Select “Quick Setup” for basic settings with simple way.

Press “Next” to start the Setup Wizard.

Step 1: Change System Password. Set up your system password. (Default：admin)

Step 2: Select Time Zone.

Step 3:

Select WAN Type. Choose Auto-Detecting or Manually to set WAN Type.

+ 44 hidden pages

iBall Baton iB-W3GB150N User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual