Hyundai Electronics H-CMMD4059 User manual

H-CMMD4059

MULTIMEDIA DVD RECEIVER

WITH MOTORIZED 7” TFT DIS-

PLAY AND TV TUNER

МУЛЬТИМЕДИЙНЫЙ

DVD-РЕСИВЕР С

МОТОРИЗИРОВАННЫМ 7” TFT-

ДИСПЛЕЕМ И ТВ-ТЮНЕРОМ

Руководство по эксплуатации Instruction manual

Table of contents Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards

Installation/Connection

Installation

General notes DIN front/rear mounting DIN front mount (Method A) Dismantling the unit Trim frame installation DIN-rear mount (Method B) Detachable control panel Anti-theft system

Connection

Connection diagram Using the ISO Connector ISO connection table Parking wire connection Reverse driving cable connection Illumination wire

Operation

Control elements

Front panel Remote controller Changing the battery

General operations

Touch screen Turning the unit on/off Open the monitor Volume control Setting the sound characteristics Mute function Mode selection Angle setting Monitor in/out AV in jack Subwoofer Dual zone function

System setup

Sound page

Display page

RDS and Radio page

General page

DVD page

System info page

Radio operations

User interface of Radio mode

Band selection

Manual/automatic tuning

Programming tuner stations

Auto memory store/preset scan

RDS background

AF (Alternative frequencies) function

TA (Traffic alarm) function

Program type (PTY)

TV tuner operations

Disc/USB/SD/MMC operations

USB/SD/MMC notes

9 10 10 10 11 11 11 12 12 12 12 12 12 12 12 12 13 13 13

Insert/Eject disc Inserting a memory card/USB device DVD touch interface VCD touch interface MP3/DivX/JPEG touch interface Play/pause Stop playback Selecting tracks Fast forward/rewind A-B segment repeat Repeat playback Intro playback Goto Random playback OSD function Zooming in/out PBC function Changing angle Selecting audio language

13 13 13 13 14 14 14 15 15 15 15 15 15 16 16 16 16 16 16 16 17 17 17 17 17 18 18 18 18 18 19 19 19 19 19 19 19 19 19

2 3

Selecting subtitle language Selecting sound channel Menu navigation ID3 tag function

General information

Handling compact discs

Cleaning discs Cleaning the unit body Accessories Troubleshooting guide Specification

19 19 19 19 20 20 20 20 20 21 22

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual to

familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• “CLASS 1 LASER PRODUCT”

This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

• Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.

• Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.

• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

• Using the unit with the temperature that goes beyond the operation temperature greatly decreases the operation resource of the screen

and other components of the unit and can result in an outage.

• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please ensure it before installation.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified technician check the system.

• Always keep the volume low enough so that you can hear sounds from outside the vehicle.

• Should this product fail to operate properly, contact your dealer or nearest service center.

Installation/Connection

Installation

General notes

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

• Before finally installing the unit, connect the wiring and make sure that the unit works properly.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• If installation angle exceeds 35° from horizontal, the unit may not perform properly.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

Din Front/Rear-Mount

This unit can be properly installed either from ‘Front’ (conventional DIN Front-mount) or ‘Rear’ (DIN Rear-mount installation, utilizing threaded screw Holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

1. DIN front-mount (Method A)

1. Car dashboard

2. Sleeve

3. Screw

4. Nut (5 mm)

5. Spring washer

6. Screw (5 х 25 mm)

7. Metal strap

8. Flat washer

182

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve and screw in four frontal screws.

Dismantling the unit

a – Trim frame b – Frame uninstall direction c – Screws to be taken out

Installation/Connection

1. Switch off the unit and detach the front

panel.

2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.

3. Unscrew the four frontal screws nad pull out the unit from the sleeve towards yourself. Before detaching the unit, ensure it is not fixed with the metal strap.

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first.

2. DIN rear-mount (Method B)

For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.

1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.

2. Screw.

3. Factory radio mounting brackets.

4. Vehicle dashboard.

5. Lock (remove this part).

The outer trim frame and mounting

sleeve are not used for method of installation.

Detachable control panel

Put the right fixing hole of the panel onto the locker on the right side of the body, then press on the left part of the panel until a click.

To detach the front panel, press REL button. When it unfastens, carefully pull the panel out.

The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

Anti-theft system

The front panel of this unit can be stored in the included protective case when not in used and carried away when you leave the vehicle to deter theft.

Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you.

Connection

Connection diagram

Subwoofer (black wire with green head)

Camera (black wire with yellow head)

Rear video out (black wire with yellow head)

TV antenna (black wire with black head)

Radio antenna (black wire with black head)

Installation/Connection

Rear output left (grey wire with white head)

Rear output left (grey wire with red head)

Line output front left (brown wire with white head)

Line output front right (brown wire with red head)

Line output rear left (grey wire with white head)

Line output rear right (grey wire with red head)

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

1. 2.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections.

Installation/Connection Installation/Connection

ISO connection table

Location Function

Connector A Connector B 1 - Rear right (+) - Purple 2 Reverse/Pink Rear right (-) - Purple/Black 3 Parking/Brown Front right (+) - Grey 4 Battery +12V/Yellow Front right (-) - Grey/Black 5 Antenna, Amplifier control/Blue Front left (+) - White 6 Illumination/Orange Front left (-) - White/Black 7 Ignition/Red Rear left (+) - Green 8 Ground/Black Rear left (-) - Green/Black

Power antenna wire is intended for power supply of the antenna and for remote control of an additional amplifier.

8 9

Parking wire connection

Parking brake lead

Brown Wire

Brake light

Battery

Car frame

If Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled by driving status, system setup and input video sources. When the car is moving ahead, if the video disc is played, the screen shows “ATTENTION!! You cannot use this function while driving”, and blank screen. The above warning screen will prevent the driver from watching images.

Reverse driving cable connection

Car frame

Pink wire

Rear view video camera lead

If the rear view video camera is connected, the unit automatically switches to CAMERA source during reverse driving. The unit returns to the original work mode after the reverse driving is done.

Reverse driving light

Gearbox

Battery

Car frame

Illumination wire

The illumination wire should be connected to marker lights of the vehicle. The illumination (backlight) backilght is possible only when the marker lights are switched on.

Operation

Control elements

Front panel

1. TFT display

2. OSD button

3. IN/OUT button

4. TILT button

5. AF/TA button

6. PTY button

7. LCD display

8. BAND/P.SCN button

9. OPEN button

10. MODE button

11. REL button

12. VOL regulator/SEL button

13. POWER/MUTE button

14. button

15.

button button

16.

17. AUX input

18. Disc slot

19. SD/MMC card slot

20. IR sensor

21. EJ button

22. USB port (under plastic cover)

Not indicated: panel status indicator (under the front panel) - flashes when the front panel is detached

1 2 3 4

5 6 7 8 9

10 11 12 13 14 15 16 17 18 19 20 21 22

Remote controller (RC)

1 2

3 4 5

6 7 8

10 11

12 13

1. MODE button

2. POWER button

3. UP cursor button

4. BND/RDM button

5. ENTER button

6. LEFT cursor button

7. DOWN cursor button

8. EJECT button

9. PTY button

10. P.SCN/RPT button

11. SEEK-/ button

12. AF button

13. OSD button

Operation

/PBC button

14.

15. Digit buttons

16. button

16 17

18 19

20 21 22 23 24 25 26 27 28 29

30 31

17. MUTE button

18. MENU button

19. SUB-T button

20. RIGHT cursor button

21. SETUP button

22. ANGLE button

23. INT button

24. VOL+ button

25. A-B/ZOOM button

26. SEL button

27. SEEK+/ button

28. VOL- button

29. AUDIO/GOTO button

30. TILT button

31. DUAL button

Changing the battery

1. Press the catch and at the same time pull

out the battery tray.

2. Insert the 1 lithium battery, type CR2025 (3 V) battery with the stamped (+) mark facing upward. Insert the battery tray into the remote controller.

• Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.

• Do not recharge, short, disassemble or

heat the battery or dispose it in a fire.

• Do not expose or bring into contact the battery with other metallic materials. Doing this may cause the battery to give off heat, crack or start a fire.

• When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may give off heat, crack or start a fire.

• Please direct the Remote controller to the IR sensor of the front panel.

Operation Operation

General operations

Touch screen

Due to the touch screen, you can fulfill most functions not only by pressing buttons but also by touching the options you need.

Turning the unit on/off

Press any button (except REL button and EJECT button) to switch the unit on. Press and hold POWER button on the RC or POWER/ MUTE button on the panel to turn off the power.

Open the monitor

Press OPEN button on the unit to open the monitor. Press the button again, the monitor returns to the previous state. Do not obstruct opening/closing the monitor and do not do it manually.

Volume control

Press VOL+/VOL- buttons on the RC or rotate VOL regulator on the unit to increase/ decrease the sound level.

Setting the sound characteristics

Press SEL button to open the following menu:

1 2 3 4

go to the mode list.

You can also adjust Equalizer, Bass, Treble, Balance and Fader by pressing the cursor buttons on the RC.

Mute function

Press MUTE button on the RC or POWER/ MUTE button on the unit to turn off the sound. Press the button again or adjust volume to resume the sound output.

Mode selection

• Repeatedly press MODE button on the RC or on the unit to select a mode: Radio => Disc => USB => SD => TV => AV-in.

• In any mode touch right top corner of the screen or press MENU button on the RC to display the Main menu as follows:

In the menu, touch the item of the mode you

need to select the corresponding mode.

The Disc, USB and SD modes are only available when a disc, USB or SD/MMC card is inserted into the unit.

Angle setting

Press repeatedly TILT button to adjust the

desired angle of the monitor.

Please do not adjust the monitor tilt

1. Setting list. Touch a setting to select its

adjustment.

2. Adjustment buttons. Touch them to adjust

corresponding setting.

3. Adjustment slidebar. Touch to adjust a

setting.

4. Equalizer mode selection button. Touch to

12 13

manually, otherwise it can get damaged.

Monitor in/out

Press repeatedly IN/OUT button on the front panel to adjust the monitor in/out position when the monitor is opened.

AV in jack

AV jack is intended to receive audio and video

signals by connecting to external device.

Subwoofer

Connect a subwoofer to this unit using the Subwoofer output of this unit. For subwoofer operation an external amplifier is required.

Dual zone function

DUAL - dual zone function enabling user to listen to radio or watch TV in the front zone, and at the same time play audio or video from disc, USB or memory card.

For Dual zone en external monitor with is required having its own acoustic system and possibility of volume adjustment.

Press and hold SEL button on the front panel or press DUAL button on the RC to select between C-DUAL (buttons perform operations for the current mode of the front zone) or D-DUAL (buttons perform DVD functions).

System setup

When you select SETTING mode or press SETUP button on the RC, the menu will be displayed, in which you can touch any item to perform operations as follows:

1 2 3 4

3. Adjustment buttons.

4. Option selection button. Touch to go to option list for corresponding setting. Touch an option to select it.

5. Subpage number.

6. Subpage selection button. Touch to switch between suppages of each setting list.

You can also navigate in the menu by pressing cursor buttons on the RC and confirm your selection by pressing ENTER button on the RC.

Sound page

• EQ: Select Flat, Classic, Pop, Rock or

User equalizer mode.

• Bass: Adjust the low-frequency level.

• Treble: Adjust the hogh-frequency level.

• Balance: Adjust the balance between left

and right channels.

• Fader: Adjust the balance between front

and left channels.

• Volume: Adjust the sound volume level.

• Beep: Select ALL (beep is heard at any button pressing), 2ND (beep is heard when a button is pressed and held) or OFF (no beep).

• Loud: Selecting loudness ON will emphasize the low frequency output.

• Subwoofer: set the subwoofer on or off.

Display page

• Screen: Select 16:9, 4:3 or FULL screen modes.

• Backlight: select LOW, MID or HIGH display backlight level.

5 6

1. Menu page list. Touch any page icon to go

to corresponding menu page.

2. Setting list. Touch a setting to select its

adjustment.

RDS and Radio page

• Stereo: Select ON (stereo reception mode) or OFF (mono reception). When the received stereo signal is weak, switch to mono mode to improve the signal. The function is available only in FM bands.

• Local: Select ON (only local station reception) or OFF (local and distant station reception). The function is available only in FM bands.

• TA volume: Adjust level of TA volume.

• Retune: Long/Short. RETUNE refers to the

Operation

time period the unit allows for radio scan when reception is interrupted. “Short” represents a time period of 30 seconds and “Long” represents a time period of 90 seconds.

• PI: Mute/Sound. PI sound refers to the reception noise when the AF function tries to scan alternative frequency.

• REG: REG ON (the receiver accepts regional variants of the tuned station with REG icon turned on), and REG OFF (the receiver ignores regional variants).

• Mask: DPI/ALL. During MASK DPI mode, the unit will mask only the AF which has different PI, this is the default mode; during MASK ALL mode, the unit will mask the AF which has different PI and no RDS signal with high field strength.

• EON TA: DX/Local. If you want to receive information from local stations only, select EON TA Local mode. Otherwise, select EON TA DX mode.

• TA: Seek/Alarm. In TA SEEK mode, the unit will seek for traffic announcement program when TA is pressed; in TA ALARM mode, no TA/TP is displayed and the alarm is set off.

General page

• Dual: Select ON or OFF the Dual zone function.

• Key: Use buttons at CURRENT (buttons perform operations for the current mode of the front zone) or DVD (buttons perform DVD functions). This function is available only if ON is selected for DUAL.

• Tilt angle: Select the monitor tilt angle.

• Tilt IN/OUT: Select the monitor in/out position.

• Clock display: Select ON (clock is displayed) or OFF (clock is not displayed).

• Clock hour: select 12-hour or 24-hour clock display mode.

• Clock setting: A touchable keyboard is displayed. Input the current time and touch OK to confirm.

language.

• Subtitle lang: Select a DVD subtitle

language.

• Audio lang: select a language of the DVD

audio.

• DVD menu lang: Select a language of the

DVD menu.

• Password: In order to make the Rating feature work, the password mode must be turned on. If you want to set the ratings limit, you will need to enter the default password, which is 0000, then press ENTER to confirm. To change the password, enter the Password change submenu. If you change the password, the default password 0000 will be void.

• Rating: The Rating control level is for parents to control playing content and protect your children from violence and erotic. The disc, the level of which is higher than the setting level can not be played.

• TV shape: Select 4:3/PS (the wide-screen image shows on the full screen, but some part is cut off, 4:3/LB (the wide-screen image shows and black bars appear on the top and bottom of screen, Wide (wide-screen image is shown).

• NTSC/PAL: Select color system NTSC or PAL.

• Default: Reset to the initial factory settings.

System info page

In this menu you can see the current version information. Besides, calibration function is available:

• Calibration: “Carefully press and hold stylus on the center of the target longer than 1 second” is displayed. Touch and hold the red cross in each position until it moves to a different position. After repeating it 4 times, the calibration of the screen is complete. The calibration procedure is useful when some malfunction occur with the touch screen, and it needs adjustment.

DVD page

• OSD lang: Select on-screen display

Operation

Radio operation

User interface of Radio mode

1 2 3 4 5 6

7 8 9 10 11 12 13 14 15 16 17

When the unit is switched to Radio mode, the above touchable user interface will be displayed on the display.

1. PTY button. Touch to enable/disable PTY function. In the PTY list, touch a program type to start its search.

2. TA button. Touch to enable/disable TA function.

3. AF button. Touch to enable/disable AF function.

4. ST button. Touch to select stereo/mono reception mode.

5. Current band and frequency.

6. Preset station button. Touch to select the station. Touch and hold to save the current frequency under the preset number.

7. LOC button. Touch to select local/distant station reception.

8. Mute button; touch to switch sound on/off.

9. Volume down button. Touch to decrease volume.

10. Volume level.

11. Volume up button. Touch to increase volume.

12. BAND button. Touch to select bands.

13. AS/PS button. Touch to scan all saved stations in current band. Touch and hold to find and save 6 availble stations in current band.

14. the nearest station downwards.

button. Touch for automatic search of

15. button. Touch repeatedly to change

frequency step by step downwards.

16.

frequency step by step upwards.

the nearest station upwards.

button. Touch repeatedly to change

17. button. Touch for automatic search of

Band selection

Press BAND/RDM button on the RC or BND/P.SCN button on the panel to switch to the bands in the following order: FM1 - FM2 FM3 - MW1 - MW2.

Manual/automatic tuning

• Manual tuning: press / buttons on the panel or SEEK-/ RC and hold for 2 seconds to enter the manual tuning mode. Press these buttons repeatedly to select a frequency downward or upward step by step.

• Automatic tuning: press on the panel or SEEK-/ the RC, the automatic search will start. It will play when finds the station.

and SEEK+/ on the

/ buttons

and SEEK+/ on

Programming tuner stations

There are 6 numbered preset buttons on the RC, with which you can store and recall stations for each band (18 FM, 12 MW). Select a station, then press and hold a preset button. The station will be saved in the memory under the corresponding number. To recall a stored station, press the corresponding preset button.

Auto memory store/Preset scan

Auto store: Select a band, press and hold BAND/P.SCN button on the panel or P.SCN/ RPT button on the RC to enter auto store mode. The radio will automatically store 6 stations to the 6 preset memories of the current band. To stop auto store, press the button again.

During auto station preset, the unit will search and store stations with the strong signal first, and then weaker signal stations until the memories are full.

Preset scan: Select a band, press BAND/P.

+ 32 hidden pages

Hyundai Electronics H-CMMD4059 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual