Hyundai Electronics H-CMD4030 User manual

H-CMD4030

MULTIMEDIA DVD/CD/MP3 RECEIVER WITH BUILT-IN 3” TFT DISPLAY AND TV-TUNER

МУЛЬТИМЕДИЙНЫЙ DVD/CD/

MP3-РЕСИВЕР

СО ВСТРОЕННЫМ 3” TFT-

ДИСПЛЕЕМ И TB-ТЮНЕРОМ

Руководство по эксплуатации Instruction manual

Table of contents Before you start

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards

Installation/Connection

Installation

General notes Din Front/Rear-Mount

1. DIN front-mount (Method A) Dismantling the unit Trim frame installation

2. DIN rear-mount (Method B) Detachable control panel Anti-theft system

Connection

Connection diagram ISO connection table Using the ISO connector Parking wire connection

Operation

Control elements

Front panel Inner panel Remote controller Changing battery General operations

Reset the unit

Turning on/off

Volume control

Mute function

Setting the sound characteristics

System setup

Mode selection

AUX jack Radio operations

Band selection

Manual/Auto tuning

Programming preset stations

Auto memory store/Preset scan

Stereo/Mono reception

On-screen display

RDS function

AF (Alternative Frequencies) function

TA (Traffic Alarm)/TP function

PTY (Program Type)

TV tuner operations

Disc/USB/SD/MMC operations

USB/SD/MMC notes

Insert/Eject discs

Inserting a memory card/USB device

Play/pause

MP3/DivX/JPEG file playback

Stop playback

Selecting tracks

Fast forward/rewind

A-B segment repeat

Repeat playback

Intro playback

Goto

Random playback

OSD function

Zooming in/out

PBC function

Changing angle

Selecting audio language

9 10 10 10 10 10 10 10 11 12 12 12 12 12 12 12

Selecting subtitle language Selecting audio channel Menu navigation ID3 tag information

General information

Handling compact discs Cleaning discs Cleaning the unit body Accessories Troubleshooting guide Specification

12 12 12 13 13 13 13 13 13 14 14 14 14 14 14 14 15 15 15 15 15 15 15 15 15 15 15 15 15 16 16 16 16 16 17 18

2 3

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual to

familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• “CLASS 1 LASER PRODUCT”

This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

• Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.

• Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.

• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

• Using the unit with the temperature that goes beyond the operation temperature greatly

decreases the operation resource of the screen and other components of the unit and can result in an outage.

• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please ensure it before installation.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified technician check the system.

• Keep the volume low enough so that you can hear sounds from outside the vehicle.

• Should this product fail to operate properly, contact your dealer or nearest service center.

Installation/Connection

Installation

General notes

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

• Before finally installing the unit, connect the wiring and make sure that the unit works properly.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• If installation angle exceeds 30° from horizontal, the unit may not perform properly.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

Din Front/Rear-Mount

This unit can be properly installed either from ‘Front’ (conventional DIN Front-mount) or ‘Rear’ (DIN Rear-mount installation, utilizing threaded screw Holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

1. DIN front-mount (Method A)

1. Car dashboard

2. Sleeve

3. Screw

4. Nut (5 mm)

5. Spring washer

6. Screw (5 х 25 mm)

7. Metal strap

8. Flat washer

182

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve until the side locks are fixed.

Dismantling the unit

a – Trim frame b – Frame uninstall direction c – Release key insertion

Installation/Connection

1. Switch off the unit and detach the front

panel.

2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.

3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out. Before detaching the unit, ensure it is not fixed with the metal strap.

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first.

2. DIN rear-mount (Method B)

For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.

1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.

2. Screw.

3. Factory radio mounting brackets.

4. Vehicle dashboard.

5. Lock (remove this part).

The outer trim frame and mounting

sleeve are not used for method of installation.

Detachable control panel

Insert the left locker of the body into the fixing hole on the side of the panel, then insert the right locker into the right hole of the panel. Press on the upper part of the panel until a click.

To detach the front panel, press OPEN button. Hold the panel at 45 degree angle and push it to the left to detach the right locker. Then detach the left locker.

The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

Anti-theft system

The front panel of this unit can be stored in the included protective case when not in used and carried away when you leave the vehicle to deter theft.

Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you.

Installation/Connection

Connection

Connection diagram

Video out (yellow)

Parking wire (brown)

1133557

2244668

ISO connector

Line out RCA (red=right)

Line out RCA (white=left)

Antenna jack

Fuse 15 A

TV antenna

ISO connection table

Location Function

Connector A Connector B 1 - Rear right (+) - Purple 2 - Rear right (-) - Purple/Black 3 - Front right (+) - Grey 4 Battery +12V/Yellow Front right (-) - Grey/Black 5 Power antenna/Blue Front left (+) - White 6 - Front left (-) - White/Black 7 Ignition key (+12V)/Red Rear left (+) - Green 8 Ground/Black Rear left (-) - Green/Black

Power antenna wire is intended for power supply of the antenna and for remote control of

an additional amplifier.

Installation/Connection

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table above for speaker and power cable connections.

Parking wire connection

Parking brake lead

If Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled by driving status. When the car is moving ahead, if the video is played, the screen shows warning and blank screen. The warning screen will prevent the driver from watching images.

Brown Wire

Brake light

Battery

Car frame

Operation Operation

Control elements

Front panel

1. PWR/MUTE button

2. MODE button

3. VOLUME knob

4. button

5. Display

6. MEM button

1 2 3 4 5 6 7 8

13 12 11 10 9

7. OK button

8. OPEN button

9. USB slot

10. AUX in jack

11. button

12. BAND button

13. MENU button

Inner panel

1 2 3 54

1. SD/MMC memory card slot

2. EJECT button

3. Panel status indicator

4. RESET button (hole)

5. Disc slot

8 9

Pressing RESET hole will erase the

clock setting and stored stations.

Panel status indicator lights up when you slide the panel down, flashes when you remove the panel.

Remote controller

1 2

3 4 5

6 7 8

10 11

12 13

15. Digit buttons

16.

button

16 17

18 19

20 21 22 23 24 25 26 27 28 29

17. MUTE button

18. MENU button

19. SUB-T button

20. RIGHT cursor button

21. SETUP button

22. ANGLE button

23. INT button

24. VOL+ button

25. A-B/ZOOM button

26. SEL button

27. SEEK+/ button

28. VOL- button

29. AUDIO/GOTO button

Changing the battery

1. Press the catch and at the same time pull

out the battery tray.

2. Insert the 1 x lithium battery, type CR 2025 3 V with (+) mark facing up. Insert the battery tray into the remote control.

1. MODE button

2. POWER button

3. UP cursor button

4. BND/RDM button

5. ENTER button

6. LEFT cursor button

7. DOWN cursor button

8. STEREO/MONO button

9. PTY/MDC button

10. P.SCN/RPT button

11. SEEK-/ button

12. AF/TA button

13. OSD button

14.

/PBC button

Operation

General operations

Reset the unit

Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press RESET button (hole) with a pointed object (such as a ballpoint pen) to set the unit to initial state.

When some errors occur, you can also press RESET button to resume to normal, and it will erase the clock setting and some memorized functions.

Turning on/off

Press any button on the panel or the RC (except OPEN button) to turn on the unit. Press and hold PWR/MUTE button on the panel or press POWER button on the RC to turn off the unit.

Volume control

Rotate VOLUME regulator or press VOL+/ VOL- buttons on the RC to adjust the volume level.

Mute function

Press PWR/MUTE button on the panel or MUTE button on the RC to turn the sound off. “MUTE” will be displayed. Press this button again or adjust the volume to turn the sound on.

Setting the sound characteristics

Press SEL button on the RC to call setting menu consisting of following items: EQ => BASS => TREBLE => BALANCE => FADER => VOLUME => BEEP => LOUDNESS. Press UP/DOWN cursor buttons on the RC or rotate VOLUME knob on the panel to select the audio setting item. Press ENTER button or RIGHT cursor button on the RC or OK button on the panel to enter the selected item.

Press LEFT/RIGHT buttons on the RC or rotate VOLUME knob on the panel to adjust the audio setting. Press SEL button on the RC again to save the setting and return to current mode.

If turn off the power, all the settings of each mode will be saved. If turn off the ACC power, all the settings will be clear and become factory default setting. If you don’t adjust setting within several seconds after selecting the desired setting item, the unit will automatically return to the current mode.

If Flat, Classic, Pop or Rock equalizer mode is selected, treble and bass are not adjustable. For operation with Beep and Loudness see below System Setup paragraph.

System setup

Press MENU button on the panel or SETUP button on the RC to enter Setting Menu. Press UP/DOWN cursor buttons on the RC or rotate VOLUME knob on the panel to select a menu page. Press ENTER button or RIGHT cursor button on the RC or press OK button on the panel to enter the page. Press UP/DOWN cursor buttons on the RC or rotate VOLUME knob on the panel to select an item, then press ENTER button on the RC or OK button on the panel to adjust the setting.

SOUND page

• EQ: Select Flat, Classic, Pop, Rock or

User equalizer mode.

• Bass: Adjust the low-frequency level.

• Treble: Adjust the hogh-frequency level.

• Balance: Adjust the balance between left

and right channels.

• Fader: Adjust the balance between front

and left channels.

• Volume: Adjust the sound volume level.

• Beep: Select ALL (beep is heard at any button pressing), 2ND (beep is heard when a button is pressed and held) or OFF (no beep).

• Loudness: Selecting loudness ON will emphasize the low frequency output.

DISPLAY page

• Screen: Select 16:9, 4:3 or FULL screen modes.

• Backlight: select LOW, MID or HIGH display backlight level.

RADIO page

Operation

• Area: Select radio broadcasting area (Europa, USA, South Amercia and Russia) to enable or disable OIRT band.

• Stereo: Select ON (stereo reception mode) or OFF (mono reception). When the received stereo signal is weak, switch to mono mode to improve the signal. The function is available only in FM bands.

• Local: Select ON (only local station reception) or OFF (local and distant station reception). This is available only for FM bands.

• TA volume: Adjust level of TA volume.

• Retune: Long/Short. RETUNE refers to the time period the unit allows for radio scan when reception is interrupted. “Short” represents a time period of 30 seconds and “Long” represents a time period of 90 seconds.

• PI: Mute/Sound. PI sound refers to the reception noise when the AF function tries to scan alternative frequency.

• REG: REG ON (the receiver accepts regional variants of the tuned station with REG icon turned on), and REG OFF (the receiver ignores regional variants).

• Mask: DPI/ALL. During MASK DPI mode, the unit will mask only the AF which has different PI, this is the default mode; during MASK ALL mode, the unit will mask the AF which has different PI and no RDS signal with high field strength.

• EON TA: DX/Local. If you want to receive information from local stations only, select EON TA Local mode. Otherwise, select EON TA DX mode.

• TA: Seek/Alarm. In TA SEEK mode, the unit will seek for traffic announcement program when TA is pressed; in TA ALARM mode, no TA/TP is displayed and the alarm is set off.

GENERAL page

• Clock display: Select ON (clock is displayed) or OFF (clock is not displayed).

• Clock hour: select 12-hour or 24-hour clock display mode.

• Clock setting: Press number buttons to input the current time. Press ENTER button on the RC to confirm.

DVD page

• OSD language: Select on-screen display

language.

• Subtitle lang: Select a DVD subtitle

language.

• Audio lang: select a language of the DVD

audio.

• DVD menu lang: Select a language of the

DVD menu.

• Password: In order to make the Rating feature work, the password mode must be turned on. If you want to set the ratings limit, you will need to enter the default password, which is 0000, then press ENTER to confirm. To change the password, enter the Password change submenu. If you change the password, the default password 0000 will be void.

• Rating: The Rating control level is for parents to control playing content and protect your children from violence and erotic. The disc, the level of which is higher than the setting level can not be played.

• TV shape: Select 4:3/PS (the wide-screen image shows on the full screen, but some part is cut off, 4:3/LB (the wide-screen image shows and black bars appear on the top and bottom of screen, Wide (wide-screen image is shown).

• NTSC/PAL: Select color system NTSC/PAL.

• Default: Reset to the initial factory settings.

SYSTEM INFO page In this menu you can see the current version

information.

Mode selection

Repeatedly press MODE button on the RC or on the panel to select a mode: Tuner => DVD => USB => Card => TV => AV IN.

The DVD, Card and USB modes are only available when corresponding storages are inserted into the unit.

AUX jack

AUX-in jack is intended for connecting an external audio or video equipment to amplify the sound. If connection is made correctly, the audio signal from the external source will be translated through the acoustics of the head

Operation Operation

unit. This enables to adjust the volume and quality of the sounding. For example, you can connect an MP3-player to listen to tracks using the car acoustic system.

Radio operations

Band selection

Press repeatedly BAND button on the panel or RDM/BAND button on the RC to select your desired radio band in RADIO mode: FM1 - FM2

- FM3 (OIRT) – MW1 (AM1) - MW2 (AM2). In each set of the bands you can store up to 6 preset stations, making total 30 preset memory stations.

Manual/automatic tuning

• Manual tuning: Press and hold SEEK- / SEEK+ buttons on the RC to enter manual tuning mode. MANUAL will be displayed. Press these buttons repeatedly to change the frequency upward or downward step by step.

• Automatic tuning: Press repeatedly SEEK- /SEEK+ buttons on the RC or press and hold these buttons on panel to start automatic seeking for an available radio station downward or upward. After being found the station will be played. To stop seeking, press one of these buttons again.

Programming preset stations

• There are 6 numbered preset buttons on the RC, with which you can store and recall stations for each band (18 FM, 6 AM). Select a station, then press and hold a preset button. The station will be saved in the memory under the corresponding number. To recall a stored station, press the corresponding preset button.

• You also can save stations in the memory with MEM button on the front panel. When the needed frequency is found, press MEM, then rotate VOLUME knob to select a memory position (Preset 1 - 6) and press OK button to confirm saving.

Auto memory store/Preset scan

Auto store: Select a band, press and hold P.SCN/RPT button on the RC to enter auto store mode. The radio will automatically store 6 stations to the 6 preset memories of the current band. To stop auto store, press the button again.

During auto station preset, the unit will search and store stations with the strong signal first, and then weaker signal stations until the memories are full.

Preset scan: Select a band, press P.SCN/ RPT button on the RC to scan all preset stations in the memories of the current band. To stop preset scan, press the button again.

Stereo/Mono reception

In FM mode, press STEREO/MONO button on the RC to select stereo or mono signal reception mode.

On-screen display

Press OSD button on the RC to show enabled PTY function icon.

RDS function

RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either.

AF (Alternative frequencies) function

Press and hold AF/TA button on the RC or MENU button on the panel to enable AF function. When the radio signal strength is poor, enabling the AF function will allow the unit to automatically search another station with the same PI (Program Identification) as the current station but with stronger signal strength.

AF indicator on the display will flash until RDS information is received. If RDS service is not available in your area, turn off the AF mode.

TA (Traffic alarm) function

Press AF/TA button on the RC or press and hold OK button on the panel to activate the traffic alarm function.

12 13

When TA function is activated, it will search the station with TA information automatically. If there is no TA information, it will search the station with TP information automatically, if there is no TP information either, it will return to the previous station after searching.

When receiving the station with TP information but without TA information, TP icon is on and TA icon keeps blinking; when receiving the station with TP and TA information, both TP and TA icons are on.

When playing in other mode and TA information is received, it will change to the radio mode automatically. After playing over, it will return to the previous mode. Press AF/TA button on the RC once to ignore the received TA information, do it twice to turn off the function.

PTY (Program type) function

Press PTYMDC button on the RC to open PTY program type list, and repeat pressing PTY/MDC button to select a PTY type. After selecting the program type you want, press number buttons 1 - 6 on the RC to start search. Press it again to stop the PTY search. If PTY code is different or not available, “PTY NONE” blinks on the display.

Other functions

For additional options, such as TA Volume, Retune, EON TA, Region, Mask, please see “Radio page“ of “System Setup“ chapter.

TV tuner operations

on the RC or rotate VOLUME knob on the panel to select an item, and then press ENTER button on the RC or OK button on the panel to adjust the setting. Press to return to last settings list.

AUTO PROGRAM

• System: select TV system (SECAM/PAL).

• Audio: select sound system (DK/BG/I).

• Search: select to start automatical search

and storing of TV channels.

MANUAL PROGRAM

• Storage: select the storage number of the

channel.

• System: select TV system (SECAM/PAL).

• Audio: select sound system (DK/BG/I).

• Channel: Select the number of the channel. You can also press number buttons on the RC to select the channel number; or press SEEKor RC to go to previous or next saved channel.

• Fine: perform fine tuning of picture quality.

• Memory: select on (memorize the found channel) or off (not memorize).

or SEEK+ buttons on the panel

button on the RC

Disc/USB/SD/MMC operations

USB/SD/MMC notes

USB format supports 2.0. Capacity: up to 8

Gb.

For correct and satisfactory operation, licensed SD/MMC memory cards of famous brands should be used with this unit. Avoid using memory cards of unknown brands. Capacity: up to 8 Gb.

• Connect a TV antenna to the TV antenna

jack of the unit. Select TV mode.

• To access the TV mode menu, press and hold MENU button on front panel or press button on the RC. To select a menu page (Auto Program or Manual Program) press UP/DOWN cursor buttons on the RC or rotate VOLUME knob on the panel. To enter the selected page press ENTER button on the RC or OK button on the panel. Press UP/DOWN cursor buttons

Insert/Eject disc

• Open the front panel. Press EJECT button and insert a disc into the disc slot with label side up. The disc will be automatically loaded into the unit. Close the front panel.

• Open the front panel and press EJECT button to eject the disc from the slot. If the disc is not removed from the slot within several seconds, it will be automatically loaded into the slot again. When the disc is ejected and

+ 28 hidden pages

Hyundai Electronics H-CMD4030 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual