Hyundai Electronics H-CMD4029 User manual

H-CMD4029

MULTIMEDIA DVD/CD/MP3 RECEIVER WITH BUILT-IN 3” TFT DISPLAY

МУЛЬТИМЕДИЙНЫЙ

DVD/CD/MP3-РЕСИВЕР СО

ВСТРОЕННЫМ

3” TFT-ДИСПЛЕЕМ

Руководство по эксплуатации Instruction manual

Table of contents Before you start

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards

Installation/Connection

Installation

General notes Din Front/Rear-Mount

1. DIN front-mount (Method A) Dismantling the unit Trim frame installation

2. DIN rear-mount (Method B) Detachable control panel Anti-theft system

Connection

Connection diagram ISO connection table Using the ISO connector Parking wire connection

Operation

Control elements

Front panel Inner panel Remote controller Changing battery General operations

Turning on/off

Volume control

Mute function

Setting the sound characteristics

Setting other characteristics

Mode setting

AUX jack Radio operations

Band selection

Manual/Auto tuning

Programming preset stations

Auto memory store

Preset scan

RDS function

AF (Alternative Frequencies) function

TA (Traffic Alarm)/TP function

PTY (Program Type)

Disc/USB/SD/MMC operations

USB/SD/MMC notes

Insert/Eject discs

Inserting a memory card/USB device

Play/pause

MP3/DivX/JPEG file playback

Stop playback

Selecting tracks

Fast forward/rewind

A-B segment repeat

Repeat playback

Intro playback

Goto

Random playback

Programming playback

OSD function

Zooming in/out

PBC function

Changing angle

Selecting audio language

Selecting subtitle language

Selecting audio channel

9 10 10 10 10 10 10 11 11 11 11 12 12 12 12 12

Menu navigation

ID3 tag information System setup System setup

Language setup

Audio setup

Video setup

Digital setup

General information

Handling compact discs Cleaning discs Cleaning the unit body Accessories Troubleshooting guide Specification

12 12 13 13 13 13 13 13 13 14 14 14 14 14 14 14 14 14 14 15 15 15 15 15 15 15 15 15 15 16 16 16 17 18 18 18 18 18 19 20

2 3

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual to

familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• “CLASS 1 LASER PRODUCT”

This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

• Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.

• Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.

• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

• Using the unit with the temperature that goes beyond the operation temperature greatly

decreases the operation resource of the screen and other components of the unit and can result in an outage.

• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please ensure it before installation.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified technician check the system.

• Keep the volume low enough so that you can hear sounds from outside the vehicle.

• Should this product fail to operate properly, contact your dealer or nearest service center.

Installation/Connection

Installation

General notes

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

• Before finally installing the unit, connect the wiring and make sure that the unit works properly.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• If installation angle exceeds 30° from horizontal, the unit may not perform properly.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

Din Front/Rear-Mount

This unit can be properly installed either from ‘Front’ (conventional DIN Front-mount) or ‘Rear’ (DIN Rear-mount installation, utilizing threaded screw Holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

1. DIN front-mount (Method A)

1. Car dashboard

2. Sleeve

3. Screw

4. Nut (5 mm)

5. Spring washer

6. Screw (5 х 25 mm)

7. Metal strap

8. Flat washer

182

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve until the side locks are fixed.

Dismantling the unit

a – Trim frame b – Frame uninstall direction c – Release key insertion

Installation/Connection

1. Switch off the unit and detach the front

panel.

2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.

3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out. Before detaching the unit, ensure it is not fixed with the metal strap.

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first.

2. DIN rear-mount (Method B)

For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.

1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.

2. Screw.

3. Factory radio mounting brackets.

4. Vehicle dashboard.

5. Lock (remove this part).

The outer trim frame and mounting

sleeve are not used for method of installation.

Detachable control panel

Insert the left locker of the body into the fixing hole on the side of the panel, then insert the right locker into the right hole of the panel. Press on the upper part of the panel until a click.

To detach the front panel, press OPEN button. Hold the panel at 45 degree angle and push it to the left to detach the right locker. Then detach the left locker.

The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

Anti-theft system

The front panel of this unit can be stored in the included protective case when not in used and carried away when you leave the vehicle to deter theft.

Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you.

Installation/Connection

Connection

Connection diagram

Parking (Brown) Video out (Yellow)

Fuse (15 A)

Line-out left (White)Line-out right (Red)

ISO connector

Connector A

1. -

2. -

3. -

4. Memory +12V

5. Auto antenna output

6. -

7. +12V (to ignition key)

8. Ground

Antenna jack

Connector B

1. Rear right speaker (+)

2. Rear right speaker (-)

3. Front right speaker (+)

4. Front right speaker (-)

5. Front left speaker (+)

6. Front left speaker (-)

7. Rear left speaker (+)

8. Rear left speaker (-)

ISO connection table

Location Function

Connector A Connector B 1 - Rear right (+) - Purple 2 - Rear right (-) - Purple/Black 3 - Front right (+) - Grey 4 Battery +12V/Yellow Front right (-) - Grey/Black 5 Power antenna/Blue Front left (+) - White 6 - Front left (-) - White/Black 7 Ignition key (+12V)/Red Rear left (+) - Green 8 Ground/Black Rear left (-) - Green/Black

Power antenna wire is intended for power supply of the antenna and for remote control of

an additional amplifier.

Installation/Connection

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table above for speaker and power cable connections.

Parking wire connection

Parking brake lead

If Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled by driving status. When the car is moving ahead, if the video is played, the screen shows warning and blank screen. The warning screen will prevent the driver from watching images.

Brown Wire

Brake light

Battery

Car frame

Operation Operation

Control elements

Front panel

1. PWR/MUTE button

2. MODE button

3. VOLUME knob

4. button

5. Display

6. MEM button

1 2 3 4 5 6 7 8

13 12 11 10 9

7. OK button

8. OPEN button

9. USB slot

10. AUX in jack

11. button

12. BAND button

13. MENU button

Inner panel

1 2 3 54

1. SD/MMC memory card slot

2. EJECT button

3. Panel status indicator

4. RESET button (hole)

5. Disc slot

8 9

Pressing RESET hole will erase the

clock setting and stored stations.

Panel status indicator lights up when you slide the panel down, flashes when you remove the panel.

Remote controller

1 2

3 4 5

6 7 8

10 11

12 13

15. Digit buttons button

16.

16 17

18 19

20 21 22 23 24 25 26 27 28 29

17. MUTE button

18. MENU button

19. SUB-T button

20. RIGHT cursor button

21. SETUP button

22. ANGLE button

23. INT button

24. VOL+ button

25. A-B/ZOOM button

26. SEL button

27. SEEK+/ button

28. VOL- button

29. AUDIO/GOTO button

Changing the battery

1. Press the catch and at the same time pull

out the battery tray.

2. Insert the 1 x lithium battery, type CR 2025 3 V with (+) mark facing up. Insert the battery tray into the remote control.

1. MODE button

2. POWER button

3. UP cursor button

4. BND/RDM button

5. ENTER button

6. LEFT cursor button

7. DOWN cursor button

8. STEREO/MONO button

9. PTY/PROG button

10. P.SCN/RPT button

11. SEEK-/ button

12. AF/TA button

13. OSD button

14. /PBC button

Operation

General operations

Turning on/off

Press any button (except OPEN button) to turn on the unit. Press and hold PWR/MUTE button on the panel or POWER button on the RC to switch the unit off.

After the unit is off, the volume level and radio current settings will be memorized, and when you turn the unit on it will resume the stored status you previously set. To protect your ear from too loud sound, the unit volume level will turn to 20 automatically when you turn the unit on if currect volume level setting is above 20 when your turn the unit off.

Volume control

Rotate VOLUME regulator or press VOL+/ VOL- buttons on the RC to adjust the volume level.

Mute function

Press PWR/MUTE button on the panel or MUTE button on the RC to turn the sound off. Press it again or adjust the volume to turn the sound on.

Setting the sound characteristics

• Press SEL button on the RC to enter the audio setting menu consisting of following items: Bass =>Treble => Balance => Fader => EQ.

• Press UP/DOWN cursor buttons on the RC or rotate VOLUME regulator on the panel to select a setting. Press ENTER button on the RC or OK button on the panel to confrim the selected setting. Press LEFT/RIGHT cursor buttons on the RC or rotate VOLUME regulator on the panel to adjust the setting.

• Press SEL button again to confirm and return to current mode.

If turning off the power all the settings of each mode will be saved. If turning off the ACC power all the settings will reset to default values. If you don’t adjust setting within several seconds after selecting the desired setting, the unit will automatically return to the current mode.

Setting other characteristics

• Press MENU button to enter the setting

mode.

• In the menu press UP/DOWN cursor buttons on the RC or rotate VOLUME knob on the panel to select a setting page. Press ENTER button or LEFT cursor button on the RC or press OK button on the panel to go to the selected page.

• In the selected page press UP/DOWN cursor buttons on the RC or rotate VOLUME knob on the panel to select a setting. Press ENTER button on the RC or OK button on the panel to adjust the selected setting.

• After you performed the adjustment, press MENU button to return to the setting page. Press MENU button again to quit setting menu.

• Following setting pages are available:

AUDIO (available in Radio, Disc, USB and

Card modes):

Bass: support 10 levels. Default level is 0. Treble: support 10 levels. Default level is 0. Balance: support 10 levels for each left and

right channel. Default is left equal to right.

Fader: support 10 levels for each front and

rear channel. Default is front equal to rear.

EQ: DSP OFF => FLAT => CLASSICS =>

POP => ROCK.

PICTURE (available in Disc, USB and Card

mode):

Red: Adjust level of red color. Support 50

levels. Default level is 25.

Green: Adjust level of green color. Support

50 levels. Default level is 25.

Blue: Adjust level of blue color. Support 50

levels. Default level is 25.

Brightness: Support 50 levels. Default level

is 25.

Contrast: Support 50 levels. Default level is 25. Sharpness: Support 15 levels. Default level

is 10.

Screen: Adjust screen size: 16:9 - 4:3 - FULL.

Color reset: Resume color default status. (Select YES or NO by cursor buttons, and press OK or ENTER button).

Operation

RDS SETUP (available in Radio, Disc, USB

and Card modes):

TA: Seek/Alarm. In TA SEEK mode, the unit will seek for traffic announcement program when TA is pressed; in TA ALARM mode, no TA/TP is displayed and the alarm is set off.

PI: Mute/Sound. PI sound refers to the reception noise when the AF function tries to scan alternative frequency.

RETUNE: Long/Short. RETUNE refers to the time period the unit allows for radio scan when reception is interrupted. “S” represents a time period of 30 seconds and “L” represents a time period of 90 seconds.

MASK: DPI/ALL. During MASK DPI mode, the unit will mask only the AF which has different PI, this is the default mode; during MASK ALL mode, the unit will mask the AF which has different PI and no RDS signal with high field strength.

EON TA: DX/Local. If you want to receive information from local stations only, select EON TA LOC mode. Otherwise, select EON TA DX mode.

REG : REG ON (the receiver accepts regional variants of the tuned station with REG icon turned on), and REG OFF (the receiver ignores regional variants).

TA VOL: Adjust level of TA volume, support 50 levels. Default level is 0.

EXPERT (available in Radio, Disc, USB and Card modes):

DX: Set radio station search by DX or LOCAL mode. When the LOCAL function is on, the local stations (stations with weak radio signal) can be played. When DX is on, both local and distant stations (stations with strong radio signal) can be played.

Stereo: Set radio reception at STEREO or MONO mode. Improvement of reception of distant stations can be done by selecting mono mode, which may cut down some reception noise. To select stereo or mono you can also press STEREO/MONO button on the RC.

Beep: BEEP ALL (beep sound will be heard when buttons are pressed), BEEP 2ND (beep

sound will be heard when buttons are pressed and held) and BEEP OFF (no beep sound for button pressing).

Loud: Set loudness on or off. LOUD function

is to emphasize the bass output.

Backlight: Set OSD backlight: MID => HIGH

=> LOW.

OSD color: Set OSD color: Dark Blue =>

Violet => Light blue.

CLOCK (available in Radio, Disc, USB and

Card modes):

Clock: Select ON to show the current time

on the display.

Clock hour: Set 12-/24-hour time mode. Clock adjust: Set the current time.

Mode setting

Press MODE button to select between unit operation modes: TUNER => Disc => USB => Card => AUX.

Disc, USB and CARD modes will only show on the display when a disc, a USB device or a memory card is inserted into the unit.

AUX jack

AUX-in jack is intended for connecting an external audio or video equipment to amplify the sound. If connection is made correctly, the audio signal from the external source will be translated through the acoustics of the head unit. This enables to adjust the volume and quality of the sounding. For example, you can connect an MP3-player to listen to tracks using the car acoustic system.

Radio operations

Band selection

Press repeatedly BAND button on the panel or RDM/BAND button on the RC to select your desired radio band in RADIO mode: FM1, FM2, FM3 (OIRT), MW. In each set of the bands you can store up to 6 preset stations, making total 24 preset memory stations.

Operation Operation

Manual/automatic tuning

Manual tuning: To find a station, select a band first, then press and hold / buttons on the RC until MANUAL appears on the display or press SEEK+/SEEK- to enter manual tuning, then press these buttons repeatedly to search for the needed frequency upward or downward.

Automatic tuning: To find a station, select a band first, then press and hold / buttons on the panel or press / buttons on the RC, the automatic downward/upward search will start. It will play when a station is found.

Programming preset stations

• To store a station: Select a band (if needed); find a station by manual/automatic tuning. Then press MEM button and rotate VOLUME knob to choose a memory position (1-6), and finally press OK button to confirm. Or, after finding a station, press and hold a number button (1-6) on the RC to save the station in the corresponding memory position.

• To recall a station: Select a band (if needed); Press / buttons on the panel. Or press a number button (1-6) on the RC to call the station saved in the corresponding position.

Auto memory store

Select a band, press and hold RPT/P.SCAN button on the RC to enter auto store mode. The radio will automatically store 6 stations to the 6 preset memories of the current band. To stop auto store, press this button again.

During auto station preset, the unit will search and store stations with the strong signal first, and then weaker signal stations until the memories are full.

Preset scan

Select a band, press RPT/P.SCAN button on the RC to scan all preset stations in the memories of the current band, each preset scan for 5 seconds. To stop preset scan, press the button again.

RDS function

RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either.

AF (Alternative Frequencies) function

Press and hold AF/TA button on the RC to turn on AF function. If the AF function is on, the display will show “AF”.

When the radio signal strength is poor, enabling the AF function will allow the unit to automatically search another station with the same PI (Program Identification) as the current station but with stronger signal strength, so that you do not have to retune the stations when driving between different transmitter coverage areas. When AF symbol is on, it means RDS information is received; when AF symbol is flashing, it means RDS information is not yet received. If RDS service is not available in your area, turn off the AF mode.

TA (Travel Announcement) / TP (Travel Program Identification)

Enable or disable TA mode by pressing and holding OK button on the front panel or by pressing AF/TA button on the RC. Default setting is OFF.

When TA function is activated, it will search the station with TA information automatically. If there is no TA information, it will search the station with TP information automatically, if there is no TP information either, it will return to the previous station after searching.

When receiving the station with TP information but without TA information, TP icon is on and TA icon keeps blinking; when receiving the station with TP and TA information, both TP and TA icons are on.

When playing in other mode and TA information is received, it will change to the radio mode automatically. After playing over, it will return to the previous mode. To ignore the TA information, press AF/TA button on the RC or press and hold OK button on the panel.

12 13

PTY (Program Type) (for FM radio)

This radio will allow you to select the type of program required, and will search for a station broadcasting that type of program.

Press PTY/PROG button on the RC repeatedly to show the various program type lists. In each list, press 1 - 6 number buttons to choose different programs available.

When PTY is selected, the radio starts to search corresponding PTY information, and stops if the corresponding PTY information is detected. If no buttons are pressed within several seconds, previously selected PTY is searched. During 1 loop, if desired PTY is not found, the unit will return to previous mode. Press PTY/PROG button on the RC to switch the PTY function off.

USB slot cover on the front panel and insert a USB into the USB slot. Then the playing mode will be changed into Card or USB mode automatically. The first card/USB device track playback will start.

When SD/MMC card and USB device are both inserted, the playing mode will be changed into the mode of the device inserted later.

Play/pause

The unit will automatically play from the first sound track recorded on a disc/SD/MMC/USB device. To ensure good system performance, wait until the unit finishes reading the disc/ device information before proceeding. Press

button on the RC to pause playback, press

it again to resume playback.

Disc/USB/SD/MMC operations

USB/SD/MMC notes

USB format supports 2.0. Capacity: up to 8

Gb.

For correct and satisfactory operation, licensed SD/MMC memory cards of famous brands should be used with this unit. Avoid using memory cards of unknown brands. Capacity: up to 8 Gb.

Insert/Eject disc

• Open the front panel. Press EJECT button and insert a disc into the disc slot with label side up. The disc will be automatically loaded into the unit. Close the front panel.

• Open the front panel and press EJECT button to eject the disc from the slot. If the disc is not removed from the slot within several seconds, it will be automatically loaded into the slot again. When the disc is ejected and removed, the unit will automatically switch to another mode.

Inserting an SD/MMC card/USB device

Open the front panel and insert an SD/

MMC memory card into the card slot. Open the

MP3/DivX/JPEG file playback

When you insert a storage containing MP3/ DivX/JPEG file, the screen will show following interface:

1 2 3 4 5

6 7 8

1. Storage folder list

2. Scroll bar

3. Current playback info

4. Current folder content (current file is

highlighted)

5. Scroll bar

6. Audio track selection

7. Image file selection

8. Video file selection

Use cursor buttons to navigate in the

+ 30 hidden pages

Hyundai Electronics H-CMD4029 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual