Hyundai Electronics H-CCR8191M User manual

H-CCR8191M

USB/SD MEDIA PLAYER

WITH BUILT-IN

3” TFT-DISPLAY

USB/SD-МЕДИАПЛЕЕР

СО ВСТРОЕННЫМ 3” ЖК-ДИСПЛЕЕМ

Руководство по эксплуатации Instruction manual

Contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards

Installation/Connection

Installation

General notes DIN front-mount Dismantling the unit Trim frame installation

Connection

Connection diagram Using the ISO Connector Parking wire connection

Operation

Control elements

Front panel Inner panel

General operations

Turning the unit on/off Reset the unit TFT display on/off Mode selection Volume control Mute function Audio parameter setting Clock Aux input System setup

Radio operations

Band select Auto/Manual tuning Automatic store/preset scan Programming tuner stations Mono/Stereo control

Local radio station search

USB/SD/MMC operations

Connecting USB/Memory card

Playback

Track select

Fast forward/rewind

Pause/Stop Aspect ratio

Repeat playback

Goto

OSD (On-Screen Display)

Selecting audio language

Selecting subtitle language

General information

Troubleshooting guide

Cleaning the unit body

Accessories

Specification

8 10 10 10 10 10 10 10 10 11 11 11 12 12 12 12 12 12

12 12 12 12 13 14 14 14 14 15 15 15 15 15 15 15 15 16

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through this manual to familiarize yourself with this high-quality sound system.

• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

• Use the unit with the temperature that goes beyond the operation temperature greatly decreases the operation resource of the screen and other components of device and can result an outage.

• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.

• Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions,

or create safety hazards such as electrical shock.

• Do not use the unit in places where it can be exposed to water, moisture and dust.

• Do not open covers and do not repair yourself. Consult the dealer or an experienced technician for help.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a qualified technician check the system.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please confirm it before installation.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

Installation/Connection

Installation

General notes

• Choose the mounting location where the unit will not interfere with the normal function of the driver.

• Before finally installing the unit, connect the wiring and make sure that the unit works properly.

• Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• If installation angle exceeds 30° from horizontal, the unit may not perform properly.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

1.DIN front-mount

1. Car dashboard

2. Sleeve

the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Make the necessary wire connections. Ensure the connections are correct.

4. Install the unit into the sleeve until the side locks are fixed.

182

1. Install the sleeve into the

dashboard; ensure it is installed with

Dismantling the unit

a – Trim frame b – Frame uninstall direction c – Release key insertion

1. Switch off the unit and detach the

front panel.

2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.

3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out. Before detaching the unit, ensure it is not fixed with the metal strap.

Installation/Connection

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first.

Installation/Connection

Connection

Connection diagram

Parking (green)

ISO connector

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

Video output(yellow)

RCA OUT Left=White Right=Red

Fuse blade 5A

connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the color code table below for speaker and power cable connections.

Antenna Socket

2. For connections without the ISO

Installation/Connection

Location Function

Connector A Connector B

1 Rear right (+) - Purple -

2 Rear right (-) - Purple/Black -

3 Front right (+) - Grey -

4 Front right (-) - Grey/Black Battery +12V/Yellow

5 Front left (+) - White Antenna power/Blue-White

6 Front left (-) - White/Black -

7 Rear left (+) - Green Ignition/Red

8 Rear left (-) - Green/Black Ground/Black

Antenna power wire is intended for power supply of the antenna and for

remote control of an additional amplifier.

Parking wire connection

Parking brake lead

Green Wire

Battery

Brake light

Car frame

If parking cable is connected to hand brake switch, the video display of the monitor will be controlled by driving status, system setup and input video sources. When the car is moving ahead, if the video is played, the screen shows warning. The warning screen will prevent the driver from watching images.

Operation

Control elements

Front panel

1. button

2. 1/OSD button

3. LIST button

4. 2/RPT button

5. APS/ button

6. Display

7. RESET button

8. /TFT OFF button

9. button

10. MOD button

1112 13 14 15 1617 18 19 20

11. 5 button

12. 3/AUD button

13. MUT button

14. VOLUME knob/SELECT button

15. 4/S-T button

16. 6 button

17. button

18. BND/TYPE button

19. USB port

20. AUX in

21. SD card slot

3 4 5 6 7

Operation

General operations

Turning the unit on/off

Press /TFT OFF button on the panel to turn the unit on. Press and hold the button to turn the unit off.

Reset the unit

Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press RESET button (hole) with a pointed object (such as a ballpoint pen) to set the unit to initial state.

When some errors occur, you can also press RESET button to resume to normal, and it will erase clock setting and some memorized functions.

TFT display on/off

When the unit is on, press /TFT OFF button on the panel to switch off the display. When the display is off, the video out signal will be available so that the connected monitor will show the screen of the unit. Press this button again to resume the image.

Mode selection

• Press repeatedly MOD button on the panel to select between Radio, USB, Memory Card and auxiliary input (AUX), operation modes. Modes of operation are indicated on the display. Memory card and USB modes are not available unless a memory card or USB device is connected.

• Or, in radio or AUX modes, press

button on the panel to display the main menu. In the menu select an operation mode by rotating VOLUME knob on the panel, then SELECT button on the panel to confirm selection.

Volume control

Adjust volume by rotating VOLUME

knob on the panel.

Mute function

Press MUT button on the panel to switch off the sound; press it again or adjust volume to resume the sound.

Audio parameter setting

Press SELECT button on the panel repeatedly to select a parameter: VOL (volume) => BAS (bass) => TRE (treble) => BAL (balance) => FAD (fader) => EQ (equalizer) => Beep => Loud ON/OFF. Rotate VOLUME knob on the panel or pressing V+/V- buttons on the RC to adjust each mode:

• Volume: from 0 to 39;

• Bass/Treble: from -7 to 7;

• Balance: L7 (left) to R7 (right);

• Fader: from R7 (rear) to F7 (front);

• EQ: select OFF/POP/ROCK/

CLASSIC equalizer mode;

• Beep on: the beep sound is heard when a button is pressed; beep off: the sound is not heard;

• Loudness: select ON or OFF. Activating this feature will enhance bass and treble frequencies when listening to music at low volumes.

When equalizer is in any mode except OFF, bass and treble are not adjustable.

Operation

Aux input

AUX-in jack is intended for connecting external audio equipment to amplify the sound. If connection is made correctly, the audio signal from the external source will be translated through the acoustics of the head unit. This enables to adjust volume and quality of sounding. For example, you can connect an MP3-player to listen to tracks using the car acoustic system.

System setup

In radio or AUX modes, press button on the panel to display the main menu. Rotate VOLUME knob on the panel to select SETUP item, then SELECT button on the panel to confirm selection The system setup menu will be displayed, in which you can adjust some system parameters. Rotate VOLUME knob to select a parameter:

• Language. Press SELECT button, then rotate VOLUME knob to select the menu language. Press SELECT button to confirm your selection.

• Date. Rotate VOLUME knob to select year, month or day. Press SELECT button to confirm your selection, then rotate VOLUME knob to adjust the selected parameter. After adjustment press SELECT button to confirm.

• Time. Rotate VOLUME knob to select hours, minutes or seconds. Press SELECT button to confirm your selection, then rotate VOLUME knob to adjust the selected parameter. After adjustment press SELECT button to confirm.

• Brightness. Press SELECT button, then rotate VOLUME knob to

adjust the image brightness. Press SELECT button to confirm.

• Reset. Press SELECT button, then rotate VOLUME knob to select YES (resetting of all user’s adjustments to default) or NO (cancel). Press SELECT button to confirm.

Radio operations

Band select

In Radio mode press BND/TYPE button to select a radio band: FM-1, FM-2, FM-3, AM-1 (MW1), AM-2 (MW2). In each set of the bands you can store up to 6 preset stations, total 30 preset memory stations.

Auto/Manual tuning

• Manual tuning: Press and hold or button on the panel until

the screen shows MANU SEEK. Press these buttons repeatedly to manually adjust the radio frequency.

• Auto tuning: Press shortly

or button, the radio will seek to the next up or down strong and clear frequency station automatically. Repeat this action to seek for other desired stations. To stop automatic search, press one of these buttons.

Automatic store/preset scan

• Automatic store: Press and

hold APS/ button. The radio will automatically store the 6 strongest available stations in each subband of the current band (FM or AM). To stop auto store, press this button again.

• Preset scan: Press APS/

button. The receiver will scan the saved stations in all subbands of the

+ 23 hidden pages