Hyundai Electronics H-CCR8103F User manual
H-CCR8103F
USB/SD MEDIA PLAYER
USB/SD-МЕДИАПЛЕЕР
Руководство по эксплуатации Instruction manual
Contents
Dear customer!
Thank you for purchasing our product. For safety, it is strongly
recommended to read this manual carefully before connecting, operating
and/or adjusting the product and keep the manual for reference in the
future.
Table of contents
Before you start
Utilization of the product
Important safeguards
Installation/Connection
Installation
General notes
1. DIN front-mount (Method A)
Trim frame installation
2. DIN rear-mount (Method B)
Dismantling the unit
Connection
Connection diagram
Using the ISO Connector
Operation
Control elements
LCD layout
General operations
Turning on/off
Mode selection
Volume control
Mute function
Preset equalizer modes
Clock
AUX input
Radio operations
Band select
Manual/Automatic tuning
Storing and recalling stations
USB/SD/MMC operations
Connecting a USB/memory
card
Playback
Track select
Fast forward/rewind
2
Pause
3
Intro playback
3
Repeat
Random
3
General information
4
Troubleshooting guide
4
Cleaning the unit body
4
Accessories
4
Specification
4
4
5
6
6
6
8
8
9
9
9
9
9
9
9
10
10
10
10
10
10
11
11
11
11
11
11
11
11
11
11
11
12
12
12
2
Before you start
Utilization of the product
If you want to dispose this product, do not mix it with general household
waste. There is a separate collection system for used electronic products
in accordance with legislation that requires proper treatment, recovery
and recycling.
Please contact your local authorities for the correct method of disposal.
By doing so, you will ensure that your disposed product undergoes the
necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health.
Important safeguards
• Read carefully through the manual
to familiarize yourself with this unit.
• Keep this manual handy as a
reference for operating procedures
and precautions. Do not allow persons
who have not read through this
manual to use this unit.
• Do not allow this unit to come into
contact with liquids. Electrical shock
could result. Also, damage to this
unit, smoke, and overheating could
result from contact with liquids or dust.
Protect this unit from moisture.
• Make sure that foreign objects do
not get inside the unit; they may cause
malfunctions, or create safety hazards
such as electrical shock or laser beam
exposure.
• The beginning of operation is
the moment of the unit installation.
Before use the device in winter it
is recommended to heat up the
passenger compartment during
20 seconds or to the operation
temperature.
• Using the unit with the
temperature that goes beyond
the operation temperature greatly
decreases the operation resource of
the screen and other components of
the unit and can result in an outage.
• Disconnect the vehicle’s negative
battery terminal while mounting and
connecting the unit.
• The unit is designed for negative
terminal of the battery, which is
connected to the vehicle metal. Please
ensure it before installation.
• When replacing the fuse, be sure
to use one with an identical amperage
rating. Using a fuse with a higher
amperage rating may cause serious
damage to the unit.
• Do not allow the speaker wires
to be shorted together when the unit is
switched on. Otherwise it may overload
or burn out the power amplifier.
• Make sure you disconnect the
power supply and aerial if you will not
be using the system for a long period
or during a thunderstorm.
• Make sure you disconnect the
power supply if the system appears to
be working incorrectly, is making an
unusual sound, has a strange smell,
has smoke emitting from it or liquids
have got inside it. Let a qualified
3
Installation/Connection
technician check the system.
• Always keep the volume low
enough so that you can hear sounds
from outside the vehicle.
• Should this product fail to
operate properly, contact your dealer
or nearest service center.
Installation
General notes
• Choose the mounting location
where the unit will not interfere with the
normal driving function of the driver.
• Before finally installing the unit,
connect the wiring and make sure that
the unit works properly.
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
• Install the unit where it does not
get in the driver’s way and cannot
injure the passenger if there is a
sudden stop, like an emergency stop.
• Avoid installing the unit where it
would be subject to high temperature,
such as from direct sunlight, or from
hot air, from the heater, or where
it would be subject to dust, dirt or
excessive vibration.
DIN front-mount (Method A)
1. Install the sleeve into the
dashboard; ensure it is installed with
the correct side and there are no
obstacles (wires, dashboard elements,
etc) for the unit installation.
2. After installing the sleeve into the
dashboard, bend tabs fitting to the
size of the dashboard to fix the sleeve
in place.
3. Make the necessary wire
connections. Ensure the connections
are correct.
4. Install the unit into the sleeve until
the side locks are fixed.
1
2
182
53
1. Dashboard
2. Sleeve tab to bend
Trim frame installation
To install the trim frame, press it
to the unit body and push it to fix it
in place. This should be done before
installing the front panel; otherwise you
are not able to install the trim frame.
DIN rear-mount (Method B)
For this method, use the screw
holes in the lateral sides of the unit.
Fix the unit with the help of the factory
radio mounting brackets.
1. Select a position in which the
screw holes of the brackets (3) are
aligned with the screw holes in the unit
body, and screw in two screws (2) in
each side.
2. Screw.
3. Factory radio mounting brackets.
4. Vehicle dashboard.
5. Lock (remove this part).
4
2
5
3
4
2
5
The outer trim frame and
mounting sleeve are not used for
method of installation.
Dismantling the unit
a – Trim frame
b – Frame uninstall direction
c – Release key insertion
a
b
c
Installation/Connection
extract the unit from the dashboard,
pull the release keys or the unit body
to pull it out.
1. Switch off the unit and detach the
front panel.
2. Insert your fingers into the groove
in the front side of the trim frame
(apply some effort to detach the
frame). Pull the frame to detach it.
3. Insert the supplied release keys
into the both sides of the unit body
to click, as shown in the picture. To
5
Installation/Connection
Connection
Connection diagram
Using the ISO Connector
1. If your car is equipped with the
ISO connector, then connect the ISO
connectors as illustrated.
2. For connections without the ISO
connectors, check the wiring in the
vehicle carefully before connecting,
incorrect connection may cause
serious damage to this unit.
RCA output left (white)
Antenna
jack
RCA output right (red)
Fuse (5 A)
ISO connector
Cut the connector, connect the
colored leads of the power cord to the
car battery as shown in the color code
table below for speaker and power
cable connections.
6
Installation/Connection
Location Function
Connector A Connector B
1 Rear right (+) - Purple -
2 Rear right (-) - Purple-Black -
3 Front right (+) - Grey -
4 Front right (-) - Grey-Black Battery +12V/Yellow
5 Front left (+) - White Power antenna/Blue-White
6 Front left (-) - White-Black -
7 Rear left (+) - Green Ignition/Red
8 Rear left (-) - Green-Black Ground/Black
Power antenna wire is intended
for power supply of the antenna and
for remote control of an additional
amplifier.
7
Operation
Control elements
1. PWR/MOD button
2. VOLUME knob/SELECT button
3. APS button
4. EQ button
5,12. / buttons
6. Display
7. Reset button (hole)
8. SD card slot
9. BND/CLK button
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20
10. MUT/LUD button
11. MON button
13. 1/ button
13. 2/INT button
14. 3/RPT button
15. 4/RDM button
17. 5/ button
18. 6/ button
19. AUX in
20. USB port
8
LCD layout
12
3
45 678910 11 12 13 14
Operation
1. Radio band indicator
2. Digit display (frequency, track time,
etc.)
3. FM frequency
4. Signal indicator
5. Not active
6. SD playback indicator
7. USB playback indicator
General operations
Turning the unit on/off
Press PWR/MOD button to turn
the unit on. Press and hold the button
again to turn the unit off.
Mode selection
Press PWR/MOD button repeatedly
to select between Radio, auxiliary
input, USB or Memory Card modes.
Modes of operation are indicated
on the display. Memory card and
USB modes are not available unless
a memory card or USB device is
connected.
8. Stereo signal reception indicator
9. Mute indicator
10. Intro mode on
11. Repeat mode on
12. Random playback on
13. Not active
14. Signal indicator
Volume control
Adjust volume by rotating VOLUME
knob.
Mute function
Press MUT/LUD button to switch
off the sound; press it again or rotate
VOLUME knob to resume the sound.
Loudness
Press and hold MUT/LUD button to
select loudness ON or OFF (when on,
loudness indicator will be displayed).
Activating this feature will enhance
bass and treble frequencies when
listening to music at low volumes.
9
Loading...