Hyundai Electronics H-CCR8090 User manual

H-CCR8090

USB/SD MEDIA PLAYER

USB/SD-МЕДИАПЛЕЕР

Руководство по эксплуатации Instruction manual

Contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards

Installation/Connection

Installation

General notes

1. DIN front-mount (Method A) Trim frame installation

2. DIN rear-mount (Method B) Dismantling the unit

Connection

Connection diagram Using the ISO Connector

Operation

Control elements LCD layout General operations

Turning on/off Mode selection Volume control Mute function Loudness Audio parameter setting Preset equalizer modes Clock AUX input

Radio operations

Band select Manual/Automatic tuning Storing and recalling stations

USB/SD/MMC operations

Connecting a USB/memory

card

Playback

Track select

Fast forward/rewind

Pause

Intro playback

Repeat

Random

General information

Troubleshooting guide

Cleaning the unit body

Accessories

Specification 6 6 6 8 8 9 9 9 9 9 9 9

10 10 10 10 10 10 10 10 11

11 11

11 11 11 11 11 11 12 12 12 12 13

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual

to familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.

• Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.

• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

• Using the unit with the temperature that goes beyond

the operation temperature greatly decreases the operation resource of the screen and other components of the unit and can result in an outage.

• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please ensure it before installation.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified

Installation/Connection

technician check the system.

• Always keep the volume low enough so that you can hear sounds from outside the vehicle.

• Should this product fail to operate properly, contact your dealer or nearest service center.

Installation

General notes

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

• Before finally installing the unit, connect the wiring and make sure that the unit works properly.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN front-mount (Method A)

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Make the necessary wire connections. Ensure the connections are correct.

4. Install the unit into the sleeve until the side locks are fixed.

182

1. Dashboard

2. Sleeve tab to bend

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame.

DIN rear-mount (Method B)

For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.

1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.

2. Screw.

3. Factory radio mounting brackets.

4. Vehicle dashboard.

5. Lock (remove this part).

The outer trim frame and mounting sleeve are not used for method of installation.

Dismantling the unit

a – Trim frame b – Frame uninstall direction c – Release key insertion

Installation/Connection

extract the unit from the dashboard, pull the release keys or the unit body to pull it out.

1. Switch off the unit and detach the

front panel.

2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.

3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To

Installation/Connection

Connection

Connection diagram

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

RCA output left (white)

Antenna jack

RCA output right (red)

Fuse (5 A)

ISO connector

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the color code table below for speaker and power cable connections.

Installation/Connection

Location Function

Connector A Connector B

1 Rear right (+) - Blue -

2 Rear right (-) - Blue/White -

3 Front right (+) - Grey -

4 Front right (-) - Grey/White Battery +12V/Yellow

5 Front left (+) - Green Power antenna/Orange

6 Front left (-) - Green/White -

7 Rear left (+) - Brown Ignition/Red

8 Rear left (-) - Brown/White Ground/Black

Power antenna wire is intended for power supply of the antenna and for remote control of an additional amplifier.

Operation

Control elements

1. / buttons

2. VOLUME knob/SELECT button

3. APS/ button

4. MUT/LUD button

5. RESET button (hole)

6. Display

7. Memory card slot

8. PWR/MOD button

9. BND/MEM button

1 2 3 4 5 6 7

8 9 10 11 12 13 14 15 16 17

10. CLK button

11. INT button

12. RPT button

13. RDM button

14. CH-/10- button

15. CH+/10+ button

16. AUX in

17. USB port

Operation

LCD layout

1 2 3 4 5

6 7 8 9 10 11 12 13 14 15 16 17

1. Memory card playback indicator

2. Not active

3. Digit display (freqeuncy, track time, etc.)

4. ROCK equalizer mode

5. POP equalizer mode

6. USB playback indicator

7. External device operation indicator

8. Repeat mode on

General operations

Turning the unit on/off

Press PWR/MOD button to turn the unit on. Press and hold the button again to turn the unit off.

Mode selection

Press PWR/MOD button repeatedly to select between Radio, auxiliary input, USB or Memory Card modes. Modes of operation are indicated on the display. Memory card and USB modes are not available unless a memory card or USB device is connected.

9. Intro mode on

10. Random playback on

11. Not active

12. Not active

13. Not active

14. Not active

15. Loudness indicator

16. Mute indicator

17. CLASS equalizer mode

Volume control

Adjust volume by rotating VOLUME

knob.

Mute function

Press MUT/LUD button to switch off the sound; press it again or rotate VOLUME knob to resume the sound.

Loudness

Press and hold MUT/LUD button to select loudness ON or OFF (when ON, LOUD will be displayed). Activating this feature will enhance bass and treble frequencies when listening to music at low volumes.

+ 18 hidden pages