Hyundai Electronics H-CCR4702M User manual

H-CCR4702M

2 DIN MULTIMEDIA

RECEIVER WITH

MOTORIZED 7” TFT DISPLAY

МУЛЬТИМЕДИЙНЫЙ

РЕСИВЕР 2 DIN

С МОТОРИЗОВАННЫМ

7” TFT-ДИСПЛЕЕМ

Руководство по эксплуатации Instruction manual

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start Utilization of the product Important safeguards Installation/Connection Installation General notes Mounting Detachable control panel Anti-theft system Connection Connection diagram Using the ISO Connector ISO connection table Parking wire connection Reverse driving cable connection Operation Control elements Front panel Remote controller Changing the battery General operations Touch screen Turning the unit on/off Reset the unit Volume control Setting the sound characteristics Mute function Mode selection Angle setting AV in jack Subwoofer System setup Sound presets Settings page Radio operations User interface of Radio mode Band selection Manual/automatic tuning

Programming tuner stations

Auto memory store

AF (Alternative frequencies) function

TA (Traffic alarm) function

Program type (PTY)

TV tuner operations

USB/SD/MMC operations

USB/SD/MMC notes

Inserting a memory card/USB device

Music mode touch interface

Play/pause

Selecting tracks

Fast forward/rewind

Repeat playback

Movie mode touch interface

Rotate function

Zooming in/out

ID3 tag function

Photo mode touch interface

Cleaning the unit body

Accessories

Troubleshooting guide

Specification 10 10 11 11 11 11 11 11 11 11 11 12 12 12 12 12

12 12 12 13 13 13 13 13 14 14 14 14 14 14 14 15 15 15 15 15 15 16 17

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual to

familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.

• Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.

• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

• Using the unit with the temperature that goes beyond the operation temperature greatly decreases the operation resource of the screen and other components of the unit and can result in an outage.

• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please ensure it before

installation.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified technician check the system.

• Always keep the volume low enough so that you can hear sounds from outside the vehicle.

• Should this product fail to operate properly, contact your dealer or nearest service center.

Installation/Connection

Installation

General notes

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

• Before finally installing the unit, connect the wiring and make sure that the unit works properly.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• If installation angle exceeds 35° from horizontal, the unit may not perform properly.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

Din Front/Rear-Mount

This unit can be properly installed either from ‘Front’ (conventional DIN Front-mount) or ‘Rear’ (DIN Rear-mount installation, utilizing threaded screw Holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

1. DIN front-mount (Method A)

1. Car dashboard

2. Sleeve

3. Screw

4. Nut (5 mm)

5. Spring washer

6. Screw (5 х 25 mm)

7. Metal strap

8. Flat washer

182

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve and screw in four frontal screws.

Dismantling the unit

a – Trim frame b – Frame uninstall direction c – Screws to be taken out

Installation/Connection

1. Switch off the unit and detach the front

panel.

2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.

3. Unscrew the four frontal screws nad pull out the unit from the sleeve towards yourself. Before detaching the unit, ensure it is not fixed with the metal strap.

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first.

2. DIN rear-mount (Method B)

For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.

1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.

2. Screw.

3. Factory radio mounting brackets.

4. Vehicle dashboard.

5. Lock (remove this part).

The outer trim frame and mounting

sleeve are not used for method of installation.

Detachable control panel

Put the right fixing hole of the panel onto the locker on the right side of the body, then press on the left part of the panel until a click.

To detach the front panel, press REL button. When it unfastens, carefully pull the panel out.

The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

Anti-theft system

The front panel of this unit can be stored in the included protective case when not in used and carried away when you leave the vehicle to deter theft.

Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you.

Installation/Connection

Connection

Connection diagram

Line out-R

Line out-L

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

1. 2.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections.

Installation/Connection

ISO connection table

Location Function

Connector A Connector B 1 - Rear right (+) - Purple 2 Reverse/Pink Rear right (-) - Purple/Black 3 Parking/Brown Front right (+) - Grey 4 Battery +12V/Yellow Front right (-) - Grey/Black 5 Antenna/Blue Front left (+) - White 6 - Front left (-) - White/Black 7 Ignition/Red Rear left (+) - Green 8 Ground/Black Rear left (-) - Green/Black

Power antenna wire is intended for power supply of the antenna and for remote control of

an additional amplifier.

Installation/Connection

Parking wire connection

Parking brake lead

Brown Wire

Brake light

Battery

Car frame

If Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled by driving status, system setup and input video sources. When the car is moving ahead, if the video disc is played, the screen shows “ATTENTION!! You cannot use this function while driving”, and blank screen. The above warning screen will prevent the driver from watching images.

Reverse driving cable connection

Car frame

Pink wire

Rear view video camera lead

Reverse driving light

Gearbox

Battery

Car frame

If the rear view video camera is connected, the unit automatically switches to CAMERA source during reverse driving. The unit returns to the original work mode after the reverse driving is done.

Control elements

Front panel

1. TFT display

2. MENU button

3. IN/OUT button

4. TILT button

5. AF/TA button

6. PTY button

7. LCD display

8. AMS button

9. OPEN button

10. MODE button

11. REL button

12. VOL regulator/SEL button

13. POWER/MUTE button

14. button

15. button

16. button

17. AV input

18. SD/MMC card slot

19. IR sensor

20. MDC button

21. USB port (under plastic cover)

Operation

1 2 3 4

5 6 7 8 9

10 11 12 13 14 15 16

20 21 22 23

Operation

Remote controller (RC)

2 3

6 7

1. MENU button

2. PWR/MUTE button

3. UP cursor button

4. MODE button

5. ENTER button

6. button

7. DOWN cursor button

8. RPT button

9. MOVIE/TA button

10. MUSIC/AF button

11. Digit buttons

12. button

13. OPEN button

14. AUDIO button

15. SUB-T button

16. button

17. VOL+ button

18. SEL button

GO TO

19. VOL- button

20. PHOTO/PTY button

21. ZOOM/GO TO button

22. SCALE/ROTATE button

23. TILT button

Changing the battery

1. Press the catch and at the same time pull

out the battery tray.

2. Insert the 1 lithium battery, type CR2025

(3 V) battery with the stamped (+) mark facing

upward. Insert the battery tray into the remote

controller.

19 20 21

• Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.

• Do not recharge, short, disassemble or

heat the battery or dispose it in a fire.

• Do not expose or bring into contact the battery with other metallic materials. Doing this may cause the battery to give off heat, crack or start a fire.

• When throwing away or saving the battery,

wrap it in tape and insulate; otherwise, the battery may give off heat, crack or start a fire.

• Please direct the Remote controller to the IR sensor of the front panel.

General operations

Touch screen

Due to the touch screen, you can fulfill most functions not only by pressing buttons but also by touching the options you need.

Turning the unit on/off

Press PWR/MUTE button on the front panel or on the RC to turn the unit on. Press and hold PWR/MUTE button on the front panel or on the RC to turn the unit off.

Reset the unit

Operating the unit for the first time or after replacing the car battery, you must reset the

Operation

unit. Press reset button on the unit with a pointed object (such as a ballpoint pen) to set the unit to initial state.

When some errors occur on the display, you can also press reset button to resume to normal, and it will erase the clock setting and some memorized functions.

Volume control

Press VOL+/VOL- buttons on the RC or on

the unit to increase/decrease the sound level.

Setting the sound characteristics

Press SEL button to switch between the following settings: Volume->BAS->TRE->BAL>FA->EQ->LOUD.

Mute function

Press MUTE button on the RC or PWR button on the unit to turn off the sound. Press the button again or adjust volume to resume the sound output.

Mode selection

• Repeatedly press MODE button on the RC or on the panel to select a mode: Radio => USB => SD => TV => AV-in.

• In any mode touch right top corner of the screen or press MENU button to display the Main menu as follows:

Angle setting

Press repeatedly TILT button on the front panel to adjust the desired angle of the monitor.

Please do not adjust the monitor tilt

manually, otherwise it can get damaged.

Press IN/OUT button to slide the screen back and forth.

AV in jack

AV jack is intended to receive audio and video signals by connecting to external device.

Subwoofer

Connect a subwoofer to this unit using the Subwoofer output of this unit. For subwoofer operation an external amplifier is required.

System setup

Sound presets

Press SEL button to switch between modes:

• Volume: Adjust the sound volume level.

• Bass: Adjust the low-frequency level.

• Treble: Adjust the high-frequency level.

• Balance: Adjust the balance between left

and right channels.

• Fader: Adjust the balance between front

and left channels.

• EQ: Select Flat, Classic, Pop, Rock or

User equalizer mode.

• Loud: Selecting loudness ON will

emphasize the low frequency output.

In the menu, touch the item of the mode you

need to select the corresponding mode.

The USB and SD modes are only available when a USB or SD/MMC card is inserted into the unit.

Settings page

+ 24 hidden pages

Hyundai Electronics H-CCR4702M User manual

Specifications and Main Features

Frequently Asked Questions

User Manual