Hyundai Digital Technology STB 100H User Manual

E M C

STB-100H

DIGITAL CABLE RECEIVER

USER'S MANUAL

CONTENTS

Note: This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of the following measures: 

◎ Reorient or relocate the receiving antenna. 
◎ Increase the separation between the equipment and receiver. 
◎ Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected. 
◎ Consult the dealer or an experienced radio/TV technician for help. 

Modifications not expressly approved by the manufacturer could void the user's authority to 
operated the equipment under FCC rules.

1. Notice 2

2. Safety/Precautions 2

2.1. Safety

2.2. Precautions

3. Menu Map 3

4. Front Panel 4

5. Rear Panel 5

6. Operation 6

7. Specifications 7

Safety/Precautions

1.1 Notice

* Theft of service is a crime.
* Installing this device without permission or unauthorized tampering,

modifying or altering it in any way may subject you
to civil or criminal penalties.

WARNING : To prevent electric shock, DO NOT REMOVE COVER.

No user serviceable parts inside.

2.1 Safty

* Be sure to read the user's manual before starting
the operation of the unit.

* Do not touch the power cord with wet hands as it may cause
electric shock.

* Never open the cover. It is very dangerous to touch
the inside of the unit due to possible electric shock.

* Place the unit in a well ventilated and no-heat environment.
* When you do not use this unit for a long time, make sure

that power cord is pulled out from the outlet. Also do not use
a damaged power cord as it may cause fire or electric shock.

* A professional installation is required. If reception is interrupted,
contact Melita Cable customer service.

2.2 Precautions

When installing the unit
* Install the unit horizontally. An uneven installation may cause
the unit to be damaged.

* Do not put heavy items such as a TV on the unit. That may cause the unit to be
damaged.

* Do not leave the unit where the water drops or splashs.
* Do not put water holding items such as vase on the unit.

Where it is subject to vibrations
Where it is exposed to direct sunlight
Where there is humidity
Where the temperature is too high or too low.
Where there is no ventilation

* Moving the unit to a hot area from a cold one will cause condensation.
* Do not operate the unit for one or two hours or until it has dried completely.

Menu Map

3. Menu Map

Main Menu channel List TV Channels

MUSIC Channels

Applications

Favorite List

Parental Control

Language

Timer

Configration Display Preferences

TV/VCR Setup

Decoder Info

Software upgrade

Diagnose

Factory Reset

4. Front Panel

Front panel

3

1 2

1. Standby/Power on Indication light : Turn on red light while in “standby mode” and turn off
red light while in “power on mode”.

2. Remote Control Indication light : Flashes green when receiving data from Remote Control Unit.

4

7 8 9

5

6

3. Power : To switch the receiver in "standby mode” or in “power on mode”.

4. Remote Sensor : Receives the infrared signal from Remote Control Unit.

5. To launch or terminate the menu application.

6. : To activate a highlighted item or go to next level on hypertext menu or confirm the user’ s
action.

7. channel : To change channel or cursor position on the application screen.

8. Volume : To adjust the volume level or change the value of an item

9. Smart Card Slot : Insert a smart card fully into the slot.

4. REAR PANEL VIEW

IEC 169-24, female

IEC 169-24, female

REAR PANEL VIEW

3 4 5

1 2

No Name Connector Function

1 TV OUT(Ch 3/4)
2 CABLE INPUT
3 CVBS RCA cinch Composite video output.
4 S/PDIF RCA cinch Digital Audio output.
5 AUDIO L RCA cinch X2 Left audio output.
6 AUDIO R RCA cinch X2 Right audio output.
7 S-VIDEO 4p Din s-video video output
8 MODEM RJ-11 Connection to teline
9 AC INPUT EN60320 AC power output

6

7

8

RF re-modulation output.

Cable signal input to Digital tuner.

9

5. Remote Control Unit

1. Power

REMOTE CONTROL UNIT

1. POWER : To switch into ‘standby’ or
power on’ mode.

2. Homepage : Moving to selected
homepage

2. Home

3. TV

4. Music

5. PPV

6. Back

8. Volum

10. Mute

12. Laguage

14. subtitle

7. Exit

9. Channel

11. Program

13. Menu

15. Favorite

16. Function&Hotkey

3. TV : Show the TV channel

4. Music : Show the music channel

5. PPV

6. Back:To return previous channel.

7. Exit:To return to previous status or menu

8. Volum:To adjust the volume level.

9. Channel:To change channel.

10. Mute:To turn the sound on/off.

11. Program :selection program

12. Laguege:To change the Laguege

13. Menu:To enter the main menu.

14. Subtitle:To see Subtitle.

15. Favorite:To see Favorite channel list.

16. Function&Hotkey

6. Channel scanning

- Press number key"007911" in above main menu

Operation

- After entering "scan network" menu, set up below values according to network set up.
* Frequency: Using number key in RCU

* Symbol rate: Using number key in RCU
* Modulation: Using right/left key in RCU

- After finishing network set up, press OK key in order to signal locking.

- After checking Level and Quality, press exit key.

7. Specifications

System capabilities Fully DVB-C(QAM) system

Connector IEC 169-24, female
Input Frequency range 47~862Mhz
Signal level -15 ~ +15 dBmV

Tuner input & Input Impedance 75 ohm

Modulation Format 64, 128, 256 QAM
FEC Annex A & C
Front end CABLE
Symbol rate 4 ~ 5.2Msps
IF Band width 6 MHz
Processor 32bit processor
SDRAM 16Mbyte
FLASH 8Mbyte

Specifications

EEPROM 32Kbyte

Video Decoder MPEG 2 Main Proflie @ Main Level

Data Rate up to 15M bits/s
Resolution 720 X 480
Video format NTSC
Aspect Ratio 4:3, 16:9

MPEG Audio MPEG 1 layer 1 & 2

Type
Sampling rates 32, 44.1 and 48 KHz

Remote control Code NEC-IR

Operating condition up to 7 Meter

Power supply Power consumption 20W

Supply voltage 90 ~ 250V

Supply frequency 50Hz ~ 60Hz
Rear panel CVBS Video output (1 cinch)
Connectors RCA Connector Audio L/R output(4 cinch)

Mono, Dual mono, Stereo, Joint Stereo

Digital Audio output(1 cinch)
Digital tuner input IEC 169-24, female
RF out put IEC 169-24, female

Physical Size(W X H X D) 260 X 53.5 X 235 (mm)
Specification Weight(Net) 2.3Kg