Hyundai HYT140 User Manual
PETROL TILLER
HYT140
User Manual
2
CONTENTS
PAGE NO.S
1
SAFETY 3 - 8
2
PART LOCATIONS
9
3
QUICK START GUIDE
10 - 15
4
STARTING PROCEDURE
16 - 17
5
STOPPING PROCEDURE
18
6
USING THE MACHINE
19 - 21
7
MAINTENANCE
22 - 29
8
LONG TERM STORAGE
29
9
TROUBLE SHOOTING
30
10
SPECIFICATION
31
11
DECLARATION OF CONFORMITY
32
12
RECYCLING & PRODUCT DISPOSAL
33
13
CONTACT DETAILS
34
14
WARRANTY 34
15
MANUAL UPDATES
34
INDEX
3
1.1
General Safety Notes.
1.2
The operator of the machine is responsible for, and has a duty of care in making sure
that the machine is operated safely and in accordance with the instructions in this
user manual. Keep the manual safe and pass it on if the machine is loaned or sold to
another user.
1.3
Please note the following safety points.
1.4
The machine should never be left it in a condition which would allow an untrained or
unauthorised person/s to operate this machine.
1.5
All due care and diligence should be taken by the operator for the safety of and with
regard to those around whilst using the machine.
1.6
Some or all of the following - warning signs, symbols and/or PPE pictograms may
appear throughout this manual. You MUST adhere to their warnings. Failure to do
so may result in personal injury to yourself or those around you.
DANGER
Indicates a hazard, which, if not avoided, could result in serious injury or death.
WARNING
Indicates a hazard, which, if not avoided, could result in serious injury.
CAUTION
Indicates a hazard which, if not avoided, might result in minor or moderate injury.
NOTE
Indicates a situation that could easily result in equipment damage.
READ and keep the manual safe and pass it on if the machine is loaned or sold to another user.
You MUST fully understand all instructions to ensure you use and operate the machine safely.
Appropriate Personal Protective Equipment (PPE), MUST be worn at all times when operating or
repairing the machine.
1. SAFETY
4
1.10
Carbon Monoxide (where applicable).
1.11
Carbon monoxide is a colourless and odourless gas. Inhaling this gas can cause
death as well as serious long term health problems such as brain damage.
1.12
The symptoms of carbon monoxide poisoning can include but are not limited to the
following;
Headaches, dizziness, nausea, breathlessness, collapsing or loss of consciousness.
1.13
Carbon monoxide poisoning symptoms are similar to flue, food poisoning, viral
infections and simply tiredness. It is quite common for people to mistake this very
dangerous poisoning for something else.
1.14
To avoid carbon monoxide poisoning DO NOT use Petrol/Diesel powered equipment
inside any of the following; Home, garage, tent, camper van, mobile home, caravan
or boat. This is not exhaustive and if you are in any doubt contact your dealer.
1.15
If you think you have or someone around you has been affected by carbon monoxide
poisoning;
1.16
Get them fresh air immediately, by leaving the affected area or by opening doors and
windows. If safe and practical to do so make sure that the machine is turned off.
DO NOT enter a room you suspect of having carbon monoxide present – instead call
the emergency services.
1.17
Contact a Doctor immediately or go to Hospital – let them know that you suspect
carbon monoxide poisoning.
1.18
DO NOT use in an enclosed area or moving vehicle.
1.20
General Fuel Safety (where applicable).
CAUTION
ALL FUELS ARE FLAMABLE
1.21
Fire Hazard – keep fuel away from all sources of ignition for example heaters.
Lamps, sparks from grinding or welding.
1.22
DO NOT carry out hot work on tanks that have contained fuel.
1.23
ALWAYS keep the work area tidy.
1.24
ALWAYS clean up spills promptly using absorbent granules and a lidded bin.
1.25
ALWAYS dispose of waste fuels correctly.
5
1.30
Fueling/De-fueling (where applicable).
CAUTION
ALL FUELS ARE FLAMABLE
1.31
ALWAYS fuel and defuel in a well ventilated area outside of buildings.
1.32
ALWAYS wear correct, suitable and fit for purpose Personal Protective Equipment
(PPE), suggested items are but not limited to safety gloves, overalls.
1.33
When fueling/de-fueling ALWAYS avoid inhaling fumes.
1.34
When de-fueling ALWAYS use a proper fuel retriever.
1.35
ALWAYS carry fuel in the correct and clearly marked container.
1.40
Electrical Safety )where applicable).
1.41
Electricity can kill – NEVER work on LIVE/ENERGISED equipment.
1.42
Prior to carrying out any maintenance work you MUST identify electrical isolation
methods and isolate all electrical supplies.
1.43
Prior to use and with all electrical supplies isolated, you MUST check all electrical
cables, plugs and connectors for the following;
1.44
Are intact and have no signs of damage, to include but not limited to bare wires,
chaffing, cuts and loose wiring.
1.45
If there are any signs of damage, the damage item MUST be taken out of service
until the damage has been repaired by an electrically competent person.
1.46
All trailing cables should be routed so as not to cause any kind of trip hazard.
1.47
NEVER work on or near electricity with wet hands, wet clothing and wet gloves.
6
1.50
Batteries (where present).
1.51
Batteries present a risk if they become damaged by the possible leaking of
electrolyte. This electrolyte is an acid and can cause serious burn injuries. Care
should be taken when working on or near them. NOTE the electrolyte may be in
a liquid or gel form.
1.52
Should you come in to contact with electrolyte you should;
1.53
Remove all clothing contaminated with electrolyte. If you cannot remove then
saturate them in water.
1.54
Get medical assistance as soon as possible. You must advise the medical staff of
the type of acid.
1.55
Lead/acid battery = dilute sulphuric acid.
1.56
Nickel/cadmium = potassium hydroxide alkali electrolyte.
1.57
Use fresh running water to wash off excess electrolyte, continue this until medical
assistance arrives. Make sure that you do not was the electrolyte to another part of
your body or face.
1.58
If electrolyte comes in to contact with Eyes the electrolyte needs to be immediately
washed away with large amounts of water. Make sure that you do not wash the
electrolyte to another part of your face or body.
1.59
Gasses from charging batteries are highly flammable and great care should be taken
to charge in well ventilated areas.
1.59.1 There is an explosion risk if the battery terminals are short circuited, when
connecting/disconnecting ALWAYS exercise great care so that the terminals or
battery leads are NOT allowed to touch and cause a spark. ALWAYS use suitable
insulated tools.
1.60
Vibrations (where applicable).
1.61
Prolonged use of hand held (operated) machines will cause the user to feel the
effects of/from vibrations. These vibrations can lead to white finger (Raynaud’s
phenomenon) or carpal tunnel syndrome. This condition reduces the ability of the
hand to feel and regulate temperature, causing numbness and heat sensations and
may cause never damage and circulatory tissue death.
1.62
Not all factors that lead to white finger disease are known, but cold weather, smoking
and other diseases that affect blood vessels and blood circulation as well as large
and long-lasting impact of shocks are considered factors in the formation of white
finger. Note the following to reduce the risk of white finger and carpal tunnel
syndrome;
1.63
Wear gloves and keep your hands warm.
1.64
Take regular breaks.
1.65
All of the above precautions may help reduce the risk of white finger disease but not
rule out the carpal tunnel syndrome. Long-term and regular users are therefore
recommended to observe the condition of your hands and fingers. Seek medical
attention immediately if any of the above symptoms should occur.
7
MACHINE SPECIFIC SAFETY
1.70
Noise (where applicable).
1.71
The operating noise of the machine can damage your hearing. Wear hearing
protection such as earplugs or ear defenders to protect your hearing. Long-term
and regular users are advised to have hearing checked regularly. Be especially
vigilant and cautious when hearing ear protection because your ability to hear alarm
warnings will be reduced.
1.72
Noise emissions for this equipment is unavoidable. Carry out noisy work at approved
times and for certain periods. Limit the working time to a minimum. For your personal
protection and protection of people working nearby it is also advisable for them to
wear hearing protection.
1.73
See Certificate of Conformity section for Outdoor Noise declaration of
conformity.
1.80
General Machine Safety.
1.81
Inspect the machine before each use and replace any damaged parts before
operation. Check for fuel leaks and make sure all fasteners are secure and in place.
1.82
Replace parts that are cracked, chipped or damaged in any way before using the
machine.
1.83
Stop the engine before working on machine for maintenance.
1.84
Never put feet or hands near the machine tiller blades when running. Before tilling,
remove all large object, which may cause injury or damage.
1.85
Keep children, people and pets at a safe distance when the tiller is in use.
1.86
DO NOT operate this rotary cultivator after drinking, taking medication or drugs
that can impair your judgment.
1.87
Use only recommended accessories and parts, approved by the manufacturer.
Non approved parts may cause damage to the machine or harm to the user,
and will also void your machine’s warranty.
1.88
Under no circumstances should you ever take the product apart or alter it in
any way even if the item is faulty. You may damage or cause further harm by
taking the product apart and you will void your warranty in doing so.
1.89
This tiller is designed exclusively for tilling in garden areas in a private,
domestic setting. Using it for any other purpose other than those intended
qualify as improper use. The operator is solely responsible for assuming all
risks.
1.90
You should prevent the equipment from coming into contact with buried
electrical cables, earthing devices, such as pipe-lines. Making contact with
these may cause electric shock and/or damage to your machine.
8
1.91
DO NOT overload the machine. For the first tilling of the season use the
highest setting. It will prevent the machine from being overloaded.
1.92
The machine will work better when operated within its specified performance
range.
1.93
If the blade is blunt, have it sharpened and rebalanced or replace it. Blunt
blades will not till the soil sufficiently so check the blades carefully before each
use.
1.94
Before maintaining or cleaning the equipment or replacing parts, cut off the
power supply of the rotary cultivator to ensure all moving parts have stopped.
1.95
The rotary tiller should be maintained by a professional maintenance person.
All maintenance or servicing by non-professionals may result in user injury or
equipment damage.
1.96
If the equipment is running abnormally, please STOP the engine and carefully
check all the parts to see if there is any damage.
Repair it before restarting or using the equipment.
1.97
DO NOT exceed the cultivable depth, DO NOT work too fast.
1.98
If the machine come into contact with big blocks, roots or vines the equipment
will spring upwards or leap forwards. Stop the machine and remove the HT
lead before removing any blockages.
1.99
Avoid pulling the tiller whilst the engine is running.
1.99.1
Keep and read the instructions often.
1.99.2
Use them to show others how to operate the tiller safely.
1.99.3
When the equipment is not being used, remove the spark plug HT lead to avoid
accidental starting.
1.99.4
You must only work in good natural daylight.
1.99.5
Correct Personal Protective Equipment (PPE) MUST be worn at all times when
operating or repairing this machine. This should include but is not limited to;
9
1 2
13 3 4
5
6
7
12 8
11 9
10
1 Throttle Lever
8 Exhaust
2 Clutch Lever
9 Transport Wheel
3 Recoil Starter Handle
10
Tiller Blades
4 Oil Filler/Dipstick
11
Depth Bar
5 Air Filter
12
Blade Cover
6 Primer Bulb
13
Handlebars
7 Spark Plug
2. PART LOCATIONS
10
3. QUICK START GUIDE
CAUTION
This guide is meant to serve as a quick reference for operating your HYT140 Tiller.
It is for convenience and the user should read and understand the manual in full first.
WARNING
This HYT140 Tiller produces Carbon Monoxide – a poisonous, colourless &
odourless gas the can cause death or serious injury, always use the machine
outdoors and in a well ventilated area.
Petrol is highly flammable, ALWAYS handle with extreme care and in a well
ventilated area.
2.0
This product comes partially assembled and is carefully packaged.
It should include the Main Unit, Handlebars, Depth bar, two identical spanners
(13mm x 10mm), Spark plug box spanner c/w T bar, User manual, Quick start guide,
Warranty registration form.
2.1
At this point, check that you have all the included items listed above.
If any items are missing or damaged then call 01646 687 880 or email
aftersales@hyundaipowerequipment.co.uk
2.2
The handlebars are not fitted to the main body of the machine but the throttle cables
are connected.
2.3
Open the box and get assistance to lift the machine clear.
Keep the box and packaging for future use.
2.4
Viewed from the rear the clutch handlebar is mounted on the left of the machine and
the throttle handlebar is mounted on the right. Undo and keep safe the six nuts, bolts
and washers on the machines support bracket.
2.5
Before offering up the handlebars to the support bracket, it is necessary for you to fit
both bars through the handlebar spacer bracket.
11
2.6
Once this has been done, you can offer each handlebar up to the support bracket,
we advise you get assistance to hold them in place whilst the fixing bolts and
washers are inserted.
2.7
Push the bolts from the outside of the handlebar then through a spring and flat
washer, then through the support bracket.
2.8
Fit the lock nut onto the bolt.
When all nuts/bolts have been fitted, tighten them all up using the spanners supplied,
to fully secure the handlebars.
2.9
When the handlebars have been fitted, you must secure the throttle/clutch cables to
their respective handlebars.
2.10
Use the clip that is fitted to each of the handlebars and ensure neither of the cables
are catching on any other part of the machine and that they are not tight.
Loading...