Hyundai H-TV1402, H-TV2102, H-TV2101PF Service Manual
SERVICE MANUAL
FILE NO. SM-CTV-O-073
COLOR TELEVISION
SERVICE MANUAL
Factory MODEL NO. 37CTV3150/54CTV3152 Hyundai: H-TV1402, H-TV2102, H-TV2101PF
CHASSIS NO. EX-1A/1A1/1A2
Please read this manual carefully before service
PRINTED IN CHINA.OCT .2003 ©
1
SERVICE MANUAL
TABLE OF CONTENTS
SPECIFICATIONS 1
SAFETY INSTRUCTIONS AND MAINTENANCE
X-RAY RADIATION PRECAUTION 2
SAFETY PRECAUTION
PRODUCT SAFETY NOTICE
SAFETY SYMBOL DESCRIPTION
MAINTENANCE
·································································································································
ADJUSTMENTS 4
SET-UP ADJUSTMENTS 4
CIRCUIT ADJUSTMENTS
CONTROL BUTTONS 13
CONTROL BUTTONS
REMOTE CONTROL 15
STRUCTURE AND CHASSIS FUNCTION DESCRIPTION 23
STRUCTURE BLOCK DIAGRAM
BLOCK DIAGRAM FOR SUPPLY VOLTAGE SYSTEM 24
CHASSIS DESCRIPTION
··················································································································
········································
···································································································
····················································································································
···········································································································
···································································································
······················································································································
··················································································································
·················································································································
·····································································································
····················································································································
······················································································································
···············
···································································································
·································································
···············································································································
2
2
3
3
4
7
13
23
25
SERVICE DATA 26
TECHNICAL DATA OF KEY ICS 26
WAVEFORMS OF KEY POINTS
SERVICE DATA OF KEY ICS
REPLACEMENT OF PARTS
····················································································································
····································································································
····································································································
·········································································································
··········································································································
44
45
49
APPENDIX
1. CIRCUIT DIAGRAMS
2. PRINTED CIRCUIT BOARD DIAGRAMS
3. FINAL WIRING DIAGRAMS
4. FINAL ASSEMBLY DIAGRAMS
2
SERVICE MANUAL
SPECIFICATIONS
Model Number 37CTV3150 54CTV3152
Color
RF system
Video system PAL4.43, NTSC3.58, NTSC4.43, PAL-M, PAL-N (50/60Hz)
Receiving
channel
Channels preset 236(0-235)
Antenna input
Picture tube Effective
screen dimensions
(Approx.)
Audio output
(THD
Power source 150-250V ~, 50Hz
Weight (Approx.) 11.5kg 23kg
Dimensions
H D) (Approx.)
(W
Rated power consumption
220V AC 50Hz
Designs and specifications are subject to change without notice.
system
Sound
system
VHF C1- C12 (49.75-85.25MHz, 168.25-216.25MHz)
UHF C13-C57 (471.25-863.25MHz)
CATV
7%)
PAL4.43, NTSC3.58, NTSC4.43,SECAM
D/K,I,M,B/G
Z1-Z7 (111.0-167.0MHz)
Z8-Z35 (223.0-447.0MHz)
(unbalanced)
75
210mm 406 305mm
280
2
1W
342 383mm 591 458 503mm
415
69W
3W+3W
1
SERVICE MANUAL
INSTRUCTIONS FOR SERVICE SAFETY AND MAINTENANCE
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE X-RA Y RADIATION PRECAUTION ,
SAFETY PRECAUTION AND PRODUCT SAFETY NOTICE INSTRUCTION BELOW.
X-RAY RADIATION PRECAUTION
1. The EHT must be checked every time the TV is serviced to ensure that the CRT does not emit
X-ray radiation as result of excessive EHT voltage. The maximum EHT voltage permissible in any
operating circumstances must not exceed the rated value. When checking the EHT, use the High
Voltage Check procedure in this manual using an accurate EHT voltmeter.
2. The only source of X-RAY radiation in this TV is the CRT. The TV minimizes X-RAY radiation, which
ensures safety during normal operation. To prevent X-ray radiation, the replacement CRT must be
identical to the original fitted as specified in the parts list.
3. Some components used in this TV have safety related characteristics preventing the CRT from
emitting X-ray radiation. For continued safety, replacement component should be made after
referring the PRODUCT SAFETY NOTICE below.
4. Service and adjustment of the TV may result in changes in the nominal EHT voltage of the CRT
anode. So ensure that the maximum EHT voltage does not exceed the rated value after service
and adjustment.
SAFETY PRECAUTION
WARNING: REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. The TV has a nominal working EHT voltage of 25kV. Extreme caution should be exercised when
working on the TV with the back removed.
1.1 Do not attempt to service this TV if you are not conversant with the precautions and procedures for
working on high voltage equipment.
1.2 When handling or working on the CRT, always discharge the anode to the TV chassis before
removing the anode cap in case of electric shock.
1.3 The CRT, if broken, will violently expel glass fragments. Use shatterproof goggles and take extreme
care while handling.
1.4 Do not hold the CRT by the neck as this is a very dangerous practice.
2. It is essential that to maintain the safety of the customer all power cord forms be replaced exactly
as supplied from factory.
3. Voltage exists between the hot and cold ground when the TV is in operation. Install a suitable
isolating transformer of beyond rated overall power when servicing or connecting any test
equipment for the sake of safety.
4. When replacing ICs, use specific tools or a static-proof electric iron with small power (below 35W).
5. Do not use a magnetized screwdriver when tightening or loosing the deflection yoke assembly to
2
SERVICE MANUAL
avoid electronic gun magnetized and decrement in convergence of the CRT.
6. When remounting the TV chassis, ensure that all guard devices, such as nonmetal control buttons,
switch, insulating sleeve, shielding cover, isolating resistors and capacitors, are installed on the
original place.
7. Replace blown fuses within the TV with the fuse specified in the parts list.
8. When replacing wires or components to terminals or tags, wind the leads around the terminal
before soldering. When replacing safety components identified by the international hazard symbols
on the circuit diagram and parts list, it must be the company-approved type and must be mounted
as the original.
9. Keep wires away from high temperature components.
PRODUCT SAFETY NOTICE
CAUTION: FOR YOU PROTECTION, THE FOLLOWING PRODUCT SAFETY NOTICE SHOULD BE
READ CAREFULLY BEFORE OPERATING AND SERVICING THIS TV SET.
1. Many electrical and mechanical components in this chassis have special safety-related
characteristics. These characteristics are often passed unnoticed by a visual inspection and the
X-ray radiation protection afforded by them cannot necessarily be obtained by using replacements
rated at higher voltages or wattage, etc. Components which have these special safety
characteristics in this manual and its supplements are identified by the international hazard
symbols on the circuit diagram and parts list. Before replacing any of these components read the
parts list in this manual carefully. Substitute replacement components which do not have the same
safety characteristics as specified in the parts list may create X-ray radiation.
2. Do not slap or beat the cabinet or CRT, since this may result in fire or explosion.
3. Never allow the TV sharing a plug or socket with other large-power equipment. Doing so may result
in too large load, causing fire.
4. Do not allow anything to rest on or roll over the power cord. Protect the power cord from being
walked on, modified, cut or pinched, particularly at plugs.
5. Do not place any objects, especially heavy objects and lightings, on top of the TV set. Do not install
the TV near any heat sources such as radiators, heat registers, stove, or other apparatus that
produce heat.
6. Service personnel should observe the SAFETY INSTRUCTIONS in this manual during use and
servicing of this TV set. Otherwise, the resulted damage is not protected by the manufacturer.
SAFETY SYMBOL DESCRIPTION
The lightning symbol in the triangle tells you that the voltage inside this product may be
strong enough to cause an electric shock. Extreme caution should be exercised when
working on the TV with the back removed.
3
SERVICE MANUAL
This is an international hazard symbol, telling you that the components identified by the
symbol have special safety-related characteristics.
UL
C UL
VDE
FDA
This symbol tells you that the critical components identified by the FDA marking have
special safety-related characteristics.
This symbol tells you that the critical components identified by the UL marking have
special safety-related characteristics.
This symbol tells you that the critical components identified by the C-UL marking have
been evaluated to the UL and C-UL standards and have special safety-related
characteristics.
This symbol tells you that the critical components identified by the VDE marking have
special safety-related characteristics.
MAINTENANCE
1. Install the TV set on a stable and level surface. Do not place the set near or over a radiator or heat
register, or where it is exposed to direct sunlight.
2. Do not install the TV set in a place exposed to rain, water, excessive dust, mechanical vibrations or
impacts.
3. Allow enough space (at least 10cm) between the TV and wall or enclosures for proper ventilation.
4. Slots and openings in the cabinet should never be blocked by clothes or other objects.
5. Please power off the TV set and disconnect it from the wall immediately if any abnormal condition
are met, such as bad smell, belching smoke, sparkling, abnormal sound, no picture/sound/raster.
Hold the plug firmly when disconnecting the power cord.
6. Unplug the TV set from the wall outlet before cleaning or polishing it. Use a dry soft cloth for
cleaning the exterior of the TV set or CRT screen. Do not use liquid cleaners or aerosol cleaners.
ADJUSTMENTS
SET-UP ADJUSTMENTS
The following adjustments should be made when a complete realignment is required or a new picture
tube is installed.
Perform the adjustments in the following order:
1. Color purity
2. Convergence
3. White balance
Notes:
The purity/convergence magnet assembly and rubber wedges need mechanical positioning.
4
SERVICE MANUAL
g
For some picture tubes, purity/ convergence adjustments are not required.
1. Color Purity Adjustment
Preparation:
Before starting this adjustment, adjust the vertical sync, horizontal sync, vertical amplitude and
focus.
1.1 Face the TV set north or south.
1.2 Connect the power plug into the wall outlet and turn on the main power switch of the TV set.
1.3 Operate the TV for at least 15 minutes.
1.4 Degauss the TV set using a specific degaussing coil.
1.5 Set the brightness and contrast to maximum.
1.6 Counter clockwise rotate the R /B low brightness potentiometers to the end and rotate the green
low brightness potentiometer to center.
1.7 Receive green raster pattern signals.
1.8 Loosen the clamp screw holding the deflection yoke assembly and slide it forward or backward to
display a vertical green zone on the screen. Rotate and spread the tabs of the purity magnet
around the neck of the CRT until the green zone is located vertically at the center of the screen.
1.9 Slowly move the deflection yoke assembly forward or backward until a uniform green screen is
obtained.
1.10 Tighten the clamp screw of the assembly temporarily. Check purity of the red raster and blue raster
until purities of the three rasters meet the requirement.
Deflection Coil
Dummy Wedge
Rubber Wedge
Glass Cloth Tapes
Purity/Convergence
Ma
net Module
Deflection Yoke
Adhesive
Fig.1
5
SERVICE MANUAL
g
y
(
)
Adj
)
4-pole Magnet
6-pole Magnet
ust the Angle (Vertical Lines
Fixed
Rotate Two Tabs At the
Same Time
Horizontal Lines
Purity Magnet
Conver
ence Magnet Assembl
Adjustment of Magnets
Fig.2
2. Convergence Adjustment
Preparation:
Before attempting any convergence adjustment, the TV should be operated for at least 15 minutes.
2.1 Center convergence adjustment
2.1.1 Receive dot pattern.
2.1.2 Adjust the brightness/contrast controls to obtain a sharp picture.
2.1.3 Adjust two tabs of the 4-pole magnet to change the angle between them and red and blue
vertical lines are superimposed each other on the center of the screen.
2.1.4 Turn both tabs at the same time keeping the angle constant to superimpose red and blue
horizontal on the center of the screen.
2.1.5 Adjust two tabs of the 6-pole magnet to superimpose red/blue line and green line.
2.1.6 Remember red and blue movement. Repeat steps2.1.3)
2..1.5) until optimal convergence is
obtained.
2.2 Circumference convergence adjustment
2.2.1 Loosen the clamp screw holding the deflection yoke assembly and allow it tilting.
2.2.2 Temporarily put the first wedge between the picture tube and deflection yoke assembly. Move
front of the deflection yoke up or down to obtain better convergence in circumference. Push the
mounted wedge in to fix the yoke temporarily.
2.2.3 Put the second wedge into bottom.
2.2.4 Move front of the deflection yoke to the left or right to obtain better convergence in
circumference.
2.2.5 Fix the deflection yoke position and put the third wedge in either upper space. Fasten the
deflection yoke assembly on the picture tube.
6
SERVICE MANUAL
2.2.6 Detach the temporarily mounted wedge and put it in either upper space. Fasten the deflection
yoke assembly on the picture tube.
2.2.7 After fastening the three wedges, recheck overall convergence and ensure to get optimal
convergence. Tighten the lamp screw holding the deflection yoke assembly.
BLU Red Red/BLU GRN
BLU
Red
4-pole Magnet Movement 6-pole Magnet Movement
Center Convergence by Convergence Magnets
Incline the Yoke up (or down) Incline the Yoke Right(or left)
Circumference Convergence by DEF Yoke
3. White Balance Adjustment
Red/BLU
GRN
Fig. 3
Generally, white balance adjustment is made with professional equipment. It’s not practical to get
2
good white balance only through manual adjustment. For TVs with I
C bus control, change the bus
data to adjust white balance.
CIRCUIT ADJUSTMENTS
Preparation:
Circuit adjustments should be made only after completion of set-up adjustments.
Circuit adjustments can be performed using the adjustable components inside the TV set. For TVs with
I2C bus control, first change the bus data.
1. Degaussing
A degaussing coil is built inside he TV set. Each time the TV is powered on, the degaussing coil will
automatically degauss the TV. If the TV is magnetized by external strong magnetic field, causing
color spot on the screen, use a specific degausser to demagnetize the TV in the following ways.
Otherwise, color distortion will be shown on the screen.
7
SERVICE MANUAL
1.1 Power on the TV set and operate it for at least 15 minutes.
1.2 Receive red full-field pattern.
1.3 Power on the specific degausser and face it to the TV screen.
1.4 Turn on the degausser. Slowly move it around the screen and slowly take it away from the TV.
1.5 Repeat the above steps until the TV is degaussed completely.
2. Supply Voltage Adjustment
Caution: +B voltage has close relation to high voltage. To prevent X-ray radiation, set +B voltage to
the rated voltage.
2.1 Make sure that the supply voltage is within the range of the rated value.
2.2 Connect a digital voltmeter to the +B voltage output terminal of the TV set. Power on the TV and set
the brightness and sub-brightness to minimum.
2.3 Regulate voltage adjustment components on the power PCB to make the voltmeter read 115±1V.
3. High Voltage Inspection
Caution: No high voltage adjustment components inside the chassis. Please perform high voltage
inspection in the following ways.
3.1 Connect a precise static high voltmeter to the second anode (inside the high voltage cap) of the
picture tube.
3.2 Plug in the supply socket (220V, AC) and turn on the TV. Set the brightness and contrast to
minimum (0
A).
3.3 The high voltage reading should be less than the EHT limitation.
3.4 Change the brightness from minimum to maximum, and ensure high voltage not beyond the
limitation in any case.
Nominal EHT voltage: 26.5
Nominal EHT voltage: 21.5
0.8KV Limited EHT voltage: 29KV(For 54CTV3152 only)
1.5KV Limited EHT voltage: 25 KV(For 37CTV3150 only)
4. Focus Adjustment
Caution: Dangerously high voltages are present inside the TV. Extreme caution should be
exercised when working on the TV with the back removed.
4.1 After removing the back cover, look for the FBT on the main PCB. There should be a FCB on the
FBT.
4.2 Power on the TV and preheat it for 15 min.
4.3 Receive a normal TV signal. Rotate knob of the FCB until you get a sharp picture.
5. Safety Inspection
5.1 Inspection for insulation and voltage-resistant
Perform safety test for all naked metal of the TV. Supply high voltage of 3000V AC, 50Hz (limit
current of 10mA) between all naked metal and cold ground. Test every point for 3 min. and ensure
no arcing and sparking.
5.2 Requirements for insulation resistance
Measure resistance between naked metal of the TV and feed end of the power cord to be infinity
with a DC-500 high resistance meter and insulation resistance between the naked metal and
8
SERVICE MANUAL
degaussing coil to be over 20M .
6. DESIGN/SERVICE mode
6.1 To enter the USER SERVICE mode
Caution: The user service mode adjustment can be changed only when service personnel adjust
the whole set data during servicing. As the control data have dramatic effects on functions and
performance of the TV, service personnel should not tell user how to
enter the SERVICE mode to avoid improper data settings.
6.1.1 Set the volume to 0. Then press and hold the MUTE button on
the remote control, and press the MENU button on the TV to
S
VS 0-3F 25
xxxxxxxx
enter the SERVICE mode. (In this case, the S mode cannot be
stored in the EEPROM. To exit from the S mode, turn off the TV set. )
6.1.2 After entering the S mode, Red
S is displayed on the upper center of the screen and MENU1
is default. Use the POS+/- buttons to highlight an adjustment and the VOL+/- buttons to adjust
it. The adjusted data are immediately output and stored in the EEPROM
6.2 Bus data in the S mode
Item Bus Data Description Remarks
5PAR/6PAR 1F Parallelogram correction (for large-screen only)
5BOW/6BOW 1F Curve correction (for large-screen only)
5HSH/6HSH Set to the optimal
mode
5HSR/6HSR Set to the optimal
mode
5EWP/6EWP 1F East-West parabola correction (for large-screen only)
5EWW/6EWW 1F East-West correction (for large-screen only)
5UCR/6UCR 1F Upper corner parabola correction (for large-screen
5LCR/6LCR 1F Lower corner parabola correction (for large-screen
5EWT/6EWT 1F Trapezoidal correction (for large-screen only)
5VSL/6VSL 1F Vertical slope (for large-screen only) *
5VAM/6VAM 1F Vertical amplitude
5SCL/6SCL Set to the optimal
mode
5VSH/6VSH Set to the optimal
mode
5VOF/6VOF Set to the optimal
mode
Horizontal center in the TV mode for 50Hz/60Hz
For 50Hz,
is displayed.
Horizontal center in the RGB mode for 50Hz/60Hz
For 50Hz, 5HSR is displayed for 60Hz, 6HSR
is displayed.
only)
only)
For 50Hz,
is displayed.
S correction *
Vertical center *
OSD vertical center *
5HSH is displayed for 60Hz, 6HSH
5VAM is displayed for 60Hz, 6VAM
*
*
*
9
SERVICE MANUAL
VX 19 Vertical zoom (for large-screen only)
RED 20 Red gun cutoff voltage *
GRN 20 Green gun cutoff voltage *
WPR 1F Red gun drive voltage *
WPG 1F Green gun drive voltage *
WPB 1F Blue gun drive voltage *
YDFP 07 PAL brightness delay time
YDFN 07 NTSC brightness delay time
YDFS 0F SECAM brightness delay time
YDAV 0F AV brightness delay time
TOP 1C UOC AGC *
VOL 32 UOC audio output amplitude *
IFFS
HDOL 00 Cathode drive level
AGC 01 IF ACG speed
VG2B 30 VG2 brightness *
SBRI 1F Sub brightness
MBRI 2F Max. brightness
SCON 20 Sub contrast
MCON 39 Max. contrast
SCOL 32 Sub color
OP1 01 Option set byte 1 54CTV3152
OP2 FF Option set byte 2
OP3 09 Option set byte 3
OP4 FF Option set byte 4
OP5 76 Option set byte 5
OP6 3C Option set byte 6
INIT EEPROM initialization
VG2 Adjusting screen voltage with VG2
VSD Vertical output off
USER_LOGO User logo write-in (valid when OP-USER-LOGO is 1)
STS0/1/2 System status byte
03
02
PIF (02-38.9MHz, 03-38MHz)
only
Notes:
The data marked with
* have been adjusted in the MANUFACTURE mode. Take care when in
service and adjustment.
To write in logo, use the
/ buttons to highlight an adjustment and the / buttons to adjust.
The data sheet may differ dependent on different models.
The data sheet may differ dependent on different CRTs for the same model.
10
SERVICE MANUAL
6.3 Option set
With remote control system software TDA935X, all options can be set in the SERVICE mode and
stored in EEPROM. Data related to picture, sound and geometric adjustment are also stored in
EEPROM.
Bit Item Description Default
OP1
OP2
0 OP_HOTEL HOTEL mode 1
1 OP_236 100/236 programs preset 0
2 OP_NTSC NTSC option set 1
3 OP_AV2 Two set of AV terminals: 1-With AV2; 0-Without AV2 1A1-1
1A/1A2-0
4 OP_SVHS S-Video terminal 1A1-1
1A/1A2-0
5 OP_DVD DVD 1A1-1
1A/1A2-0
6 OP_RGB RGB: 1- RGB 0-No 1A1-0
1A/1A2-1
7 OP_OSO Switch off in vertical overscan 0
0 OP_AVL AVL 1
1 OP_AUTO_SOUND Auto sound system test 1
2 OP_NOT_1 0
National Option Set (OP_NOT_3/2/1)
1XX-Arabic
OP3
3 OP_NOT_2 0
4 OP_NOT_3
011-Farsi 010-Russian 001-Ukrainian 000-Paneuro
0
5 OP_USER_LOGO User logo prior to CHANGHONG logo 0
6 OP_ON_BACK Auto test background options when power-on:
0
0-black; 1-blue
7 OP_FSL Slicing level for vertical sync 0
0 OP_ENGLISH English 1
1 OP_FARSI Farsi 1
2 OP_ARABIC Arabic 1
3 OP_RUSSIAN Russian 1
4 OP_FRENCH French 1
5 OP_GERMAN German 1
6 OP_INDIA Indonesian 1
7 OP_MALAYSIA Malay 1
11
SERVICE MANUAL
(continued)
OP4
OP5
0 OP_FMWS Window selection of sound pll: small/large window 0
1 OP_DIRECT_SWIT
CH_ON
2 OP_HCO EHT tracking mode 0
3 OP_CHH_LOGO User logo display 1-Displayed without signal
4 OP_SOUND_DK Sound system-DK option set 1
5 OP_SOUND_BG Sound system-BG option set 0
6 OP_SOUND_I Sound system-I option set 1
7 OP_SOUND_M Sound system-M option set 1
0 OP_TUNER Tuner 1-Philips Tuner 0-Panasonic Tuner 0
1 OP_AUTO_LANG0 1
2 OP_AUTO_LANG1 0
Memory power-on (If turned off by the remote
control, then the TV is turned on by the remote
control; if turned off by the MAIN POWER SWITCH,
then turned on by the MAIN POWER SWITCH.)
reception 0-No
Auto language option set: English - Farsi - Arabic -
Russian - French - German - Indonesian - Malay
1
1
OP6
3 OP_AUTO_LANG2
4 OP_FORF 0
5 OP_FORS
6 OP_AVON If AV off, then AV on 1
7 OP_ONPOSITION With HOTEL mode preset, on position is fixed to
0 OP_AUTOTEST Auto test when power-on 0
1 OP_PSNS Sensitivity 0
2 OP_BSCREEN Black screen when changing channels: 1-yes 0-No 1
3 OP_SECAM 1: SECAM option 1
4 OP_DFL Disable flash protection 0
5 OP_SIF External input for sound IF circuit 1
6 OP_EXT_SIF0 1
7 OP_EXT_SIF1
Field frequency options (OP_FORS/FORF):
00-Auto60Hz, 01-KeepLast
11-Auto50Hz
POS1.
Sound system options for external circuit: 00-DK,
01-BG, 10-I, 11-M
10-Force60Hz,
0
0
0
0
(Valid when OP_SIF = 1)
12
CONTROL BUTTONS
1 CONTROL BUTTONS
SERVICE MANUAL
37CTV3150
Front panel
Rear panel
MAIN POWER SWITCH
INFRARED SENSOR
POWER INDICATOR
TV/AV MENU - VOL + - CH +
MENU SELECT
TV/AV SELECT
VOLUME DOWN/UP
POSITION DOWN/UP
13
ANTENNA IN
SERVICE MANUAL
54CTV3152
Front panel
Rear panel
MAIN POWER SWITCH
OPEN THE DOOR
TV/AV SELECT
MENU SELECT
VOLUME DOWN/UP
POSITION DOWN/UP
ANTENNA IN
INFRARED SENSOR
POWER INDICATOR
14
Loading...