Hyundai H-LCD1918 Instruction Manual

H-LCD1918

	ТЕЛЕВИЗОР ЦВЕТНОГО
	ИЗОБРАЖЕНИЯ
	ЖИДКОКРИСТАЛЛИЧЕСКИЙ
LCD TV	(LCD)

Instruction manual

Руководство по эксплуатации

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents	2
Before you start	3
Utilization of the product	3
Important safeguards	3
Installation	5
Stand installation	5
Connection	6
Connection	6
Outdoor antenna connection	6
Other connections	6
Operation	7
Control elements	7
Front panel	7
Back panel	7
Remote controller	8
Changing the battery	8
General operations	9
Teletext operations	9
OSD operation	9
Picture setting (in TV mode)	9
PC setup (in VGA mode)	10
Sound setting	10
Channel setting	10
Timer setting	11
Function setting	11
General information	12
Troubleshooting	12
Causes of interference	12
Accessories	13
Specifications	13

2

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

•Please unplug the power cord from the AC outlet and contact a service center for repair

if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

•This unit should only be connected to a wall socket having grounding.

•Always disconnect the power cord and antenna during a storm.

•Do not fix the power cord with a metal nail.

•Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

•When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, refit, twist, pull or roast the power cord.

•Please contact the service center immediately if you found that the core is showed in the air or has been broken.

•Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.

•Never touch the antenna lie or power plug if it stars to thunder.

•Do not touch the power plug with wet hands.

•Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

•All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

•Please use the accessories provided

by the manufacturer. Using inadequate accessories may result in accidents.

•Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

•Over-press the panel may destroy the product.

•Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.

•Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity. Store the product with a temperature from –200C ~500C; otherwise you may destroy the product.

3

Before you start

•Do not place any vase, potted plant, cup, medicine and any container with water on this product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

•Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

•Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

•Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

•Do not place the unit into closed space

of TV for better ventilation; it can reduce the product lifetime. Keep a space at list 10 cm at above, left, and right of the TV.

•Please place all the signal cords behind of rear panel.

•Do not overexert or touch the panel when you convey the product. Do not transfer the LCD TV up or down display direction.

•Do not transport it with the power cord

or the connection cable connected. If you move this product with the power cord or the connection cable connected, the damaged power cord, connection cable or connection terminal may cause the fire, the electric shock or breakdown.

•2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.

•The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic drawings of real objects and may differ from their real images.

4

Installation

Stand installation

1. Cover an even stable surface with a soft cloth. Place the LCD TV unit facedown on the cloth. Prepare to put the stand in.

2. Fit the stand into the LCD TV unit stand socket until a click.

5

Operation

Connection

Antenna cable connector	TVRF antenna jack

75 Ohm co-axis cable

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

•Connect the audio sources to the proper stereo audio input jacks ‘L’ and ‘R’.

•Connect the video source to the video input jack by RCA cable.

•When using the TV as a computer screen, connect the PC to the VGA jack from the monitor by the relevant cable.

•This unit has PC audio in jack. Connect this jack to PC main unit with related audio cable in PC mode and adjust the volume to what you want.

•If the video source has a HDMI output jack, you can connect the signal to this unit by the HDMI cable.

•Connect an external device (e.g., VCR-/ DVD-recorder) to the proper Audio/Video output jacks of this unit with AV RCA cable.

•Component input Y/Pb/Pr is intended for receiving component video signal if connected to the component output of external signal source.

•Connect your headphones or earphones (not included) to the headphone socket of this unit. When earphones are connected, the sound output through the built-in speakers of this unit is mute.

6

Operation

Control elements

Front panel

	1	1. POWER button
	2	2.	TV/AV button
		3.	MENU button
	3	4.	VOLbutton
	4	5.	VOL+ button
		6.	CHbutton
	5	7.	CH+ button
		8.	IR sensor
	6
		9.	Power indicator
	7
	8
	9

Back panel

6

	7
1
2
3	8
4	9
	10
5	11
	12

1.Power switch

2.HDMI input

3.Video input

4.Stereo audio input (Left+Right) for component video

5.Component video (YPbPr) input

6.Headphone jack

7.PC audio input

8.VGA (PC) input

9.Stereo audio input (Left+Right)

10.RF antenna input

11.Stereo audio output (R+L)

12.Video output

7

Operation

Remote controller (RC)

14

1	15

2

3	16
4	17
5	18
6
7	19
8	20
9	21
10	22
11	23
12	24
13	25

11.Red button

12.TEXT button

13.HOLD button

14.INFO/INDEX button

15. button

16. button

17.RECALL button

18.EXIT button

19.CH+/CHbuttons

20.Not functional for this model

21.Not functional for this model

22.Yellow button

23.Blue button

24.E/W button

25.SUBPAGE button

Changing the battery

1.Remove the battery compartment cover on the back of the RC.

2.Insert the batteries into the battery compartment making sure that the correct polarity is observed.

3.Install the cover back.

1.POWER button

2.Number buttons

3.SOURCE/REVEAL button

4.SIZE/ZOOM button

5.MENU button

6.ENTER button/cursor buttons ( / / /)

7.VOL+/VOLbuttons

8.SLEEP button

9.CANCEL button

10.Green button

1

2

3

•Use two AAA batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

•Take the battery out of the RC if it is not used for a long time.

•Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

•Do not expose the RC to shock, liquids, and do not place it in an area with high humidity.

8

Operation

General operations

•Press POWER button on the unit or on the RC to switch on the power. Press POWER button again to switch the unit into standby mode.

•Press VOLbutton repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.

• Press button to cut off sound, press this button again or adjust volume to resume sound.

•Press SLEEP button repeatedly to set the sleep time. When sleep time is set, press this button to display the time remaining until the auto turn off.

•Press button in TV mode repeatedly to switch between Stereo, Mono, Dual I and Dual II sound modes (can be unavailable for some channels).

•Press SOURCE button on the RC or TV/

AV button on the unit, then press / cursor buttons to cycle through the available source list as follows: TV - AV - YPbPr - HDMI

-VGA.

•Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number from 0 to 235 directly.

•Press RECALL button on the RC to select from the present channel and the previously displayed channel.

•Press INFO button to display the preset TV channel play information.

Teletext operations (option)

Select a TV channel in order to pick up the picture signal of Teletext. Teletext button functions are as follows:

TEXT: Press TEXT button to enter into TEXT mode. Press this button again to enter mixed mode. Press the button again to return to the channel you are watching. Press / buttons or number buttons to select teletext pages.

HOLD: Press this button to stop the move to the next page. Press this button again to cancel operation.

INDEX: Press this button to go to the index page.

SIZE: Press this button to enlarge the top part of the page. Press this button again to enlarge the bottom part of the page. Press this button third time to normal size text page view.

REVEAL: Press this button to reveal the cancelled information. Press this button again to cancel the information.

SUBPAGE: Press this button to select subpage. Input the number of sub-page and use numeric buttons in the format 0001 for sub page 1. The teletext will search for the sub page. Press SUBPAGE button again to exit the subpage mode.

Red/Green/Yellow/Blue buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower parts of teletext screen.

OSD operation

Press MENU button to enter the OSD

menu. Use	/ buttons to select a setting
page. Press	/	buttons to go to the
needed item, then use		/ buttons to select

available setting or to adjust the selected item. Press ENTER button to confirm

After setting, press EXIT button to exit menu.

Picture setting (in TV mode)

PICTURE

PICTURE MODE

CONTRAST

BRIGHTNESS

SATURATION

TINT

SHARPNESS

COLOR TEMP.

ADVANCE

9