Hyundai H-DVD5041N Instruction Manual

H-DVD5041-N

DVD PLAYER

DVD ПЛЕЕР

Instruction manual

Руководство по эксплуатации

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents	2	PREV/NEXT	9
Before you start	3	Play	9
Utilization of the product	3	Pause	9
Important safeguards	3	Stop	9
Supported formats	4	Volume+/Volume-	10
Connection	5	Resume	10
Video/audio system connection	5	Return	10
Operation	6	Mute	10
Front panel	6	System setup	10
Rear panel	6	General setup	10
Remote controller	7	Audio setup	11
Changing the battery	7	Dolby setup	11
Button functions	8	Video setup	11
Power	8	Mpeg4 subtitle setup	11
Direct play	8	Preference setup	12
Open/Close	8	Other functions	12
Number buttons	8	MP3/JPEG/compressed video playback	13
Time	8	How to create a playlist	13
Display	8	General information	14
Zoom	8	Handling compact discs	14
A-B	8	Cleaning discs	14
Repeat	8	Accessories	14
Title	8	Troubleshooting	15
Step	8	Specification	16
Slow	8
N/P	8
Subtitle	8
Audio	9
LT/RT	9
Menu	9
Cursor buttons	9
Enter	9
Setup	9
PBC	9
Prog	9
Angle	9
REV	9
FWD	9

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

Warning

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Alerts the user to the presence of dangerous voltage within the product’s enclosure.

Alerts the user to the presence of important operating instructions.

To reduce the risk of electric shock or fire, do not open the cover. Refer servicing to qualified service personnel.

This mark indicates this unit belongs to class 1 laser product.

•To prevent the risk of fire or electric shock, don’t allow water to come into contact with the device and don’t use the device in high humidity conditions.

•The device is equipped with high voltage components and a laser system, hence you shall not open the device and repair it by yourself. The laser beam is dangerous to eyes when the housing is removed. Don’t look at it.

•When the device is moved from cold premises to the warm room or vice versa, condensate may form on the laser head and the device may not operate properly. In this case please turn the device on for 1-2 hours without disc before playback to heat it to a proper operation temperature.

•Don’t try to manually open or close the disc tray to load discs.

•Disconnect the receiver only when there is no disc therein.

•If you are not going to use the device for a long time disconnect it from the wall outlet.

•Before turning the device on, please make sure that you have connected it properly, adjust the volume of speakers and amplifiers of your radio system to the minimum. Adjust the volume as necessary only after normal playback has started to avoid damage of your audio system.

•Use supply sources of rated voltage, otherwise the unit may not function or may be damaged.

•Place the unit on a horizontal surface. Keep the unit ventilated. Don’t block the heat hole. Overheat may cause malfunction.

•Do not place any objects on the player’s cover, this may make it function improperly (incorrect playback).

•Please place the device in a dry and

well-aired area. Do not place it near heating units or expose it to direct sunlight, mechanical vibration, humidity or excessive dust.

•If using power plug and appliance coupler as a cutting-connecting device, it should be operated easily.

•Never use liquid detergents, abrasives or organic compounds (alcohol, gasoline, etc) to clean the unit body.

Before you start

• All repairs and technical service should be made by qualified specialist from service centers.

All images provided herein are schematic drawings of real objects and may differ from their real images.

Supported formats

Disc types	Symbol	Contents

DVD		Compressed digital audio - video

MPEG4 (DivX)		Compressed digital audio - video

Video-CD (VCD)		Compressed digital audio - video

Super-VCD (SVCD)		Compressed digital audio - video

CDDA		Digital audio

MP3		Compressed digital audio

WMA		Compressed digital audio

Kodak Picture CD		Compressed digital static image

JPEG		Compressed digital static image

Connection

Video/audio system connection

Before you start connection of external devices, ensure that power of the unit is switched off.

Following outputs are available in this unit.

Composite video

Use the cable with yellow plug of an AV cable to connect the composite video output of this unit to the video input of a TV/monitor.

SCART

Use a 21-pin SCART cable to connect the SCART output of this unit to the TV/monitor SCART input.

Stereo audio

Use a pair of AV cables (red for right/white for left) to connect the stereo audio outputs of this unit to the TV or a stereo input of power amplifier.

Coaxial digital audio

Use a special coaxial cable to connect the coaxial output of this unit to the coaxial input of an external device (e.g. amplifier with in-built DTS-decoder).

• The connection you should make depends on the TV/monitor input terminals. Don’t make all the connections at the same time; otherwise the produced picture will be affected.

•The physical connection should accord to the audio output setup of this unit.

•The unit does not support DTS sound output. To obtain DTS format sound you need to connect the unit to an external amplifier with the help of a coaxial cable (not included).

Operation

Control elements

Front panel

1	2	3	4

1.Disc tray

2.PLAY/PAUSE button

3.OPEN button

4.POWER button

5.STOP button

Rear panel

1	2
	ON

			MODEL: H-DVD5041-N
			Power supply: ~110V-240V, 50/60 Hz, 20W
			OFF
3	4	5	6

1.Coaxial digital audio output

2.Power cord

3.Mixed L/R audio output

4.Component video output

5.SCART out

6.ON/OFF power switch

Operation

Remote controller (RC)

1	17
1
	18
2
	19
3	20
4	21
5	22
6	23
7	24
8	25
9
10	26
11	27
12	28
13	29
14	30
15	31
16	32

1.POWER button

2.Digit buttons

3.ZOOM button

4.DISPLAY button

5.TITLE button

6.STEP button

7.SUBTITLE button

8.AUDIO button

9.Cursor ( / //) buttons/ENTER button

10.PBC button

11.SETUP button

12.REV/FWD buttons

13.PLAY button

14.PAUSE button

15.RESUME button

16.RETURN button

17.OPEN/CLOSE button

18.DIRECT PLAY button

19.TIME button

20.A-B button

21.REPEAT button

22.N/P button

23.SLOW button

24.MENU button

25.	LT/RT button	29. VOLUME+ button
26.	PROG button	30. STOP button
27.	ANGLE button	31.	VOLUMEbutton
28.	PREV/NEXT button 32.		MUTE button

Changing the battery

1.Remove the battery compartment cover on the back of the RC.

2.Insert the batteries into the battery compartment making sure that the correct polarity is observed.

3.Install the cover back.





1	2	3

•Use two AAA/1.5V batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

•Take the battery out of the RC if it is not used for a long time.

•Do not mix new and used batteries or different types of batteries. Weak batteries can

leak and severely damage the RC.

Operation

Button functions

POWER

When playing, press POWER button on the panel or on the RC to turn off the unit, and

standby mode will be activated; Press the button again, to turn on the unit and it will start playing.

The power is not fully turned off in standby state. If the unit will not be used for a long time, turn off the power fully by pressing power switch on the back panel.

DIRECT PLAY

If a DVD disc contains a warning or notice message or an advertisement clip, press this button to skip them and go directly to the disc contents.

OPEN/CLOSE

Press OPEN/CLOSE button on the RC or OPEN button on the panel when power is on, the disc tray is pushed out. Put the disc on the tray with the title faced up. Press the button again to close the disc tray and the unit starts playing automatically.

Number buttons

Press number buttons to input digits and numbers (e.g. track/chapter number, playback time etc.).

TIME

Press TIME button to input chapter/title number or disc time. Playback will start in accordance with the input data.

DISPLAY

Press DISPLAY button to display various info on the current playback: title/chapter time elapsed/remaining, etc.

ZOOM

When playing DVD, SVCD, VCD disc, press ZOOM button to zoom in the picture as follows: 2x => 3x => 4x => normal. In zoom in mode, press cursor buttons to move the picture for

viewing.

A - B

•Press A-B button at the start point (A) and the ending point (B) to select the repeat fragment.

•Press A-B button the third time to cancel fragment repeat and return to normal play.

REPEAT

Press REPEAT button to repeat a title, chapter, track or the whole disc.

•When playing DVD disc, press REPEAT button continually to repeat chapter => title => all => repeat off.

•When playing SVCD, VCD, CD disc, press REPEAT button continually to repeat track => all => repeat off.

•When playing MP3 disc, press REPEAT button continually to play single => repeat track => repeat all => repeat off.

TITLE

When playing a DVD disc, press TITLE button to return to the main title menu of the disc.

STEP

When playing DVD, SVCD, VCD disc, press STEP repeatedly to play video frame by frame. Press PLAY button to resume normal playback.

SLOW

Press SLOW button repeatedly to change slow playback speed as follows: X2 => X4 => X8 => X16 => normal.

N/P

Press N/P button to select between PAL/ Auto/NTSC video mode. This function is only available when no disc is inside the unit.

SUBTITLE

When playing a disc with multi-language subtitle, press SUBTITLE button continually, the subtitle languages are changed in a circle, and you can select the needed one.

Operation

AUDIO

When playing DVD with more than one audio stream, press this button to select the needed language.

LT/RT

Press this button to select the audio channel when a disc is played.

•When playing DVD disc, press MENU button once to return to the main menu of the disc.

•When playing SVCD, VCD2.0, after the disc is loaded, the unit will display the chapter menu (if PBC is on). Also, you can display this menu by pressing MENU button.

Cursor buttons

Press cursor buttons to navigate in various menus.

ENTER

Press ENTER button for confirmation of chosen options.

SETUP

Press SETUP button to enter or exit the system setup menu.

PBC

Press this button to turn on or off Playback Control (PBC) function.

PROG

•If the disc contains 2 or more tracks, chapters or titles, set up the playing order to your preference. Press PROG button to enter program menu.

•Press number buttons to input the number of the track, title or chapter. If programmed tracks are over ten, select NEXT item and press ENTER button to go on programming. Maximum 20 programmable items are possible. Use cursor buttons to move the cursor to START item. Press ENTER button to start program playback. Press PROG button to cancel programming.

For MP3 disc, this function is not available.

ANGLE

When playing the disc with multi-angle, press ANGLE button to select the view angle.

REV

Press this button for quick rewind search. Search speed will increase with each pressing: 2X => 4X => 8X => 16X => 32X => normal.

FWD

Press this button for quick forward search. Search speed will increase with each pressing: 2X => 4X => 8X => 16X => 32X => normal.

PREV/NEXT

•When playing DVD disc, press PREV button to go to the previous chapter.

•When playing SVCD, VCD, CD disc, press PREV button to go to the previous track.

•When playing DVD disc, press NEXT button to go to the next chapter.

•When playing SVCD, VCD, CD disc, press NEXT button to go to the next track.

PLAY

When the disc is paused or stopped, press PLAY button on the RC or PLAY/PAUSE button on the panel to start playback.

PAUSE

When playing the disc, press PAUSE button on the RC or PLAY/PAUSE button on the unit to pause playback.

STOP

When playing DVD, SVCD, VCD, CD disc, press STOP once, the unit will memorize the previous ending point; when afterwards you play the same disc, playback will start from the memorized point. Press STOP button two times, playback will stop without memorizing the stop point.

This function is only active when ON is

Operation

set for Last Memory item in General setup page.

VOLUME+/VOLUME-

Press VOLUME+ button to adjust volume up. Press VOLUMEbutton to adjust volume down.

RESUME

Press this button to go back to current playback after activating the disc title menu with TITLE button.

RETURN

When playing DVD, Super-VCD or VCD2.0 discs, press RETURN button to go to the disc menu. Press the button again to return to current playback. This function is not available when PBC is off.

MUTE

Press MUTE button, the sound will be turned off. Press MUTE button again, the sound will resume.

System setup

1.Press SETUP button to enter the setup menu. In Setup menu, press SETUP button again to quit the setup page.

2.Use / buttons to choose a setup page: General setup, Audio setup, Dolby setup, Video setup, Mpeg4 subtitle setup, Preference page.

3.Pressbutton to enter the setup page selected.

4.Use / buttons to select the option you want to adjust.

5.Pressbutton to enter the adjustment

list. Use / buttons to select the adjustment

and press ENTER button to confirm and button to return to options list.

6. To return to setup page list press button when in the option list.

The items in gray can’t be set up. The setup is memorized and kept after power is off.

General setup

General Audio Dolby Video MP4sub Prefer.

General Setup Page

TV format

Angle mark

OSD lang

Captions

Screen saver

Last memory

• TV format

Normal/PS: When the unit is connected to the normal TV set, the wide-screen image is shown on the full screen, but some part is cut off.

Normal/LB: When the unit is connected to the normal TV set, the wide-screen image is shown and black bars appear on the top and bottom of screen.

Wide: Use this item when the unit is connected to the normal TV set, if you want to squeeze the picture.

• Angle Mark

When playing DVD disc with multi-angle view, if selected ON, the angle mark is shown.

• OSD Lang

Select on-screen display language.

• Captions

This function doesn’t work when the disc is without caption. If the caption is OFF, press SUBTITLE button on the remote control to make caption on. The default setup is ON.

• Screen Saver

If the SCREEN SAVER is set ON and the unit is turned on without a disc playing for several minutes, a moving picture appears on the screen, and the unit will go to standby mode after several minutes. You can press POWER button to wake it up.

• Last Memory

When this function is on, the unit can memorize the time elapsed from the last time you played the disc. Then at the next playing, it will resume playing from the memorized time.

+ 23 hidden pages